TREX TRANSCEND STAIR RAILING · 2020. 11. 23. · E. Trex balusters (must also use appropriate...
Transcript of TREX TRANSCEND STAIR RAILING · 2020. 11. 23. · E. Trex balusters (must also use appropriate...
-
1
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
Standard
BALUSTER OPTIONS
Round Aluminum
Square Aluminum
A
E
F
J
C
B
G*
I**
H*
C
D
D
PARTS
A. CrownorUniversalrailB. UniversalrailC. RailingSupportBrackets(RSB)D. StairrailgasketsE. BalustersF. StairbalusterspacerG. Postsleevecap*H. Postsleeveskirt*I. Postsleeve–4"x4"(102mmx102mm)or
6"x6"(152mmx152mm)**J. Adjustablefootblock(quantityofoneisrequired
forallrailingspanlengths)***
* Item not included in the Transcend railing kits.
** Both 4" x 4" (102 mm x 102 mm) and 6" x 6"(152 mm x 152 mm) post sleeves are designed to fit over 4x4 pressure-treated post.
*** For commercial applications, spans over 6' will require two foot blocks. One will be included in kit, a second one will need to be purchased separately.
NOTE: Pictorial representations shown may only show one style of railing, while others may also be used. Review detailed instructions to determine what railing styles and combinations can be used.
DETERMINING BALUSTERS NEEDED
Baluster TypeFor 6'
Stair RailFor 8'
Stair Rail
Standard(StairApplication)
11 15
Round/SquareAluminum(StairApplication)
12 16
NOTES:» Basic installation for balusters is the same for all options. When using
round or square aluminum balusters, use correct baluster spacers.
» If installing 42" (1067 mm) railing, use longer post sleeves and measureaccordingly to ensure a proper cut. DO NOT CUT TO ACTUAL 42"LENGTH WITHOUT CONFIRMING WHAT STYLE OF RAILING YOU AREINSTALLING.
» Ensure pressure-treated posts are installed at proper heights so whenpost sleeves are installed , both the PT post and post sleeve are flushat top.
» If using post mounts, refer to detailed instructions provided with postmounts for attaching these prior to installation of any railing type.
Screws Supplied with RSBC1.WoodscrewforattachmentofRSB
towoodpost/compositesleeve
C2.Self-drillingscrewforattachmentofRSBtorail
IMPORTANT NOTES:
» TREX TRANSCEND RAILINGS ARE DESIGNED TO BE INSTALLED OVER THE DECKING FRAME OR ON INSIDE OF RIM JOIST. NOTCHING OFPRESSURE-TREATED POSTS OR POSTS INSTALLED ON OUTSIDE OF RIM JOIST IS NOT ALLOWED.
» POST TO POST SPAN WILL BE LESS THAN 6' OR 8'. PRIOR TO INSTALLING POSTS CALCULATE POST TO POST SPAN USING A MAXIMUM RAILLENGTH REQUIRED AND THE ANGLE (32°-37°) AT WHICH THE RAILS WILL BE INSTALLED. DO NOT INSTALL STAIR POSTS AT 6' OR 8' SPAN, ASSTAIR RAILINGS WILL THEN BE TOO SHORT.
Care and Cleaning
Maintaining the appearance of your Trex Transcend railing is important. The occasional wash is recommended as over time your railing may show signs of weathering as a result of exposure to the elements. The frequency of cleaning will depend on the environment and exposure to various types of ele-ments.
» Clean railing using a standard cleaning vinegar or mild soap and water.
» For more detailed cleaning recommendations please refer to the Trex Railing Care and Cleaning guide found on www.trex.com.
C1 C2
-
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
2
HaveQuestions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0420
TREX TRANSCEND STAIR RAILING CONFIGURATIONSNote: See specific installation instructions for attachment of Trex Post Mounts or Trex Joist Mount Posts prior to installing any railing.
CuttingpostsleevesisNOTrequired.A. Pressure-treatedpost/Trexpostsleeve,Trexpostmount/Trexpostsleeve,or
JoistMountPost/Trexpostsleeve(INSIDEMOUNTONLY)B. CrownrailC. UniversalbottomrailD. Trexbalusters(mustalsouseappropriatestairbalusterspacer)See page 3 for “How to Install Standard Stair Railing”.
PostsleevesWILL NEED TO BE CUT.A.Pressure-treatedpostwithTrexpostsleeve
NOTE: » Only for use with 4" x 4" (102 mm x 102 mm) post sleeve. » Trex post mounts cannot be used with Transcend
cocktail design.B. Deckboardtoprail(1x6or2x6).NOTE: Enhance or Escapes
cannot be used.C. UniversaltoprailD. UniversalbottomrailE. Trexbalusters(mustalsouseappropriatestairbalusterspacer)See page 7 for “How to Install Cocktail Stair Railing”.
CuttingpostsleevesisNOTrequired.Ensurebothtopandbottompost/postsleevesaretallenoughtoaccommodatetoprailand2"x4"(51mmx102mm).A. Pressure-treatedpost/Trexpostsleeve,Trexpostmount/Trexpostsleeve,orJoist
mountpost/Trexpostsleeve(INSIDEMOUNTONLY)B. 2"x4"(51mmx102mm)topraiC. UniversaltoprailD. UniversalbottomrailE. TrexbalustersSee page 8 for “How to Install Traditional Stair Railing”.
NOTES: » If using Round or Square Aluminum Balusters, follow desired railing style instructions found above, substituting correct
baluster spacer for type of baluster being used.
POST SLEEVES
WILL NEED TO BE CUT
A
B
D
C
E
A
B
D
C
E
Cocktail
Standard
A
B
D
C
E
Traditional
-
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0420
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
3
Installing Pressure-Treated Posts» PLEASE REFER TO
LOCAL BUILDING CODE REQUIREMENTS PRIOR TO ATTACHING PRESSURE TREATED POSTS.
» PRESSURE TREATEDPOSTS MUST BEINSTALLED ON INSIDEOF STAIR STRINGERAND AT NOSE OF STAIRTREAD.
» POST TO POST SPAN WILL BE LESS THAN 6' OR 8'.PRIOR TO INSTALLING POSTS CALCULATE POSTTO POST SPAN USING A MAXIMUM RAIL LENGTHREQUIRED AND THE ANGLE (32°-37°) AT WHICH THERAILS WILL BE INSTALLED. DO NOT INSTALL STAIRPOSTS AT 6' OR 8' SPAN, AS STAIR RAILINGS WILLTHEN BE TOO SHORT.
» Attachpostsusingcodeapprovedhardwareandalsouseaddedblocking.
» Boltscanbecountersunkflushwithframingtoallowforfasciaattachment.
» Inmostcases,apostandpostsleevelongerthan39"(991mm) willbeneededonthelowersectionofstairrailtoaccommodatestairangle.
NOTE: Blocking can be added for extra strength.
Installing Post Sleeve Skirts and Post Sleeves2. Slidepostsleeveskirtover
postanddowntorestondeckingsurface.Slidepostsleeveoverpostandpositioninsidepostsleeveskirt.
NOTE: Shims can be used toplumb post sleeves.
Measuring and Cutting Bottom Stair Rail
3. Ifusingstandardbalusters,placea1"(254mm)deckboardonthenoseofthestairtread.Ifusingaluminumbalusters,useascrappieceofwoodmeasuringatleast1-11/16"thick,andplaceonthenoseofthestairtread.
4. Snapbalusterspacerintobottomstairrailandlaybottomstairrailontopofthedeckboard
5. Usethelowerandupperstairposttosetthelengthofthebottomstairrail.Ensurethatbalusterspacerholesarespacedevenlybetweenposts.Alsoallowforaminimumof1-1/2"(292mm)ateachendofthestairrailforbracketplacementandbalusterclearance.Markrailatpostintersections.
HOW TO INSTALL STANDARD STAIR RAILINGTREX TRANSCEND
Stair Post1
1
2
2
3
1" (2.5 cm)
Standard BalustersStandard Balusters Aluminum BalustersAluminum Balusters
1 11/16" (4.3 cm)
4
1
1
2
5
-
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
4
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0420
HOW TO INSTALL STANDARD STAIR RAILING/CONTINUEDTREX TRANSCEND
Marking Location for Foot Block to Bottom Rail
6. Markapproximatelocationforfootblock,allowingameasurementof4"maximum.Invertthebottomrail,andatmarkedlocationdrillaholeusinga3/16"drillbitinthecenterofthechannel.Footblockistobeinstalledatlaststep.Forspansover6'incommercialapplications,markanddrilltwolocationsspacedevenlyapartfortwofootblocks.
Cutting Bottom Stair Rail and Baluster Spacer7. Keepingbalusterspacerin
rail,cutalongmarks.
NOTES: » If using rail gaskets,
subtract 1/16” fromeach end and cut.
» KEEP BALUSTER SPACERIN RAIL WHEN CUTTING. CUT VERY CAREFULLY TO NOTBREAK BALUSTER SPACER.
Attaching RSB’s for Bottom Stair Rail
8. Removebalusterspacerfrombottomrailandplacerailinbetweenposts,keepingrailondeckboard.
9. Markbothpostsoninsidechannelofthebottomstairrail.Removebottomstairrail.
10. ForUPPERpost–installRSB FLAT SIDE DOWN,ABOVE MARKED LINE,usingtwowoodscrewsprovided.TakesecondRSB,turnupsidedownandinterlockintofirstRSB.
11. ForLOWERpost–installRSB FLAT SIDE UP, ABOVEMARKED LINE,usingtwowoodscrewsprovided.TakesecondRSB,turnupsidedownandinterlockintofirstRSB.
Attaching Bottom (Universal) Stair Rail12. LiftbottomstairrailsoRSB’s
areinthechannelandattachwith3self-drillingscrewsprovided.UsethethreeouterholesinRSBtoattachscrews.
Tip: Deckboardcanbeplacedunderneathbottomstairrailtohelpholdrailfirmlyinplacewhileattaching.
6
2
4" (10 cm)
1
7
2
8
1
3
110
2
9
3
1
112
12 2
1
Upper Post Location - Bottom Rail
Lower Post Location - Bottom Rail
-
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0420
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
5
HOW TO INSTALL STANDARD STAIR RAILING/CONTINUEDTREX TRANSCEND
IMPORTANT NOTE IF INSTALLING ALUMINUM BALUSTERS: IfnecessarycutaluminumbalusteradaptorstripatappropriatelengthtoensurethiscanbefullyseatedintothebottomstairrailwithoutinterferingwiththeRSBs.
13. Snapbottombalusterspacerintobottomstairrail.
14. Placetwobalustersintobottomstairrailateachendclosesttothepost.andensurethesebalustersareparalleltoposts.
Tip: Useclampstohelpholdbalustersinplace.
Measuring and Cutting Top Stair Rail and Baluster Spacer
15. Snapbalusterspacerintotopstairrail.Positiontopstairrailontobalusters,ensuringbalustersarefullyseatedinrail(positiontosideofpost),andENSUREthatbalustersarespacedevenlyANDparallelwithpost.Alsoallowforaminimumof1-1/2"(292mm)ateachendofthestairrailforbracketplacementandbalusterclearance.
16. Markrailatpostintersection.
17. Removetoprail,keepingbalusterspacerinrail,andcutalongmarks.
NOTES: » If using rail gaskets, subtract
1/16” from each end and cut.» KEEP BALUSTER SPACER IN
RAIL WHEN CUTTING. CUTVERY CAREFULLY IN ORDERTO NOT BREAK BALUSTER SPACER.
18. Removebalusterspacerfromtopstairrailandplacerailinbetweenpostsontopofbalusters,ENSURINGthatbalus-tersremainparalleltopost.
19. Markbothpostsoninsidechannelofthetopstairrail.Removetopstairrail.
13
14
1
2
2
15
1
16
17
2
21
1
18
19
-
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
6
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0420
20. ForUPPERpost–installRSBFLAT SIDE DOWN BELOWMARKED LINE,usingtwowoodscrewsprovided.TakesecondRSB,turnupsidedownandinterlockintofirstRSB.
21.ForLOWERpost-installRSB FLAT SIDE UP BELOWMARKED LINE,usingtwowoodscrewsprovided.TakesecondRSB,turnupsidedownandinterlockintofirstRSB.
Installing Inverted Top Baluster Spacer and Placing Balusters
22. Placeinvertedtopbalusterspaceronbottomrailrail/balusterspacer,ensuringthatbalusterholeslineup.Installbalustersintobottomstairrail.
Attaching Top Stair Rail
23. PlacetopstairrailonRSB’s(ensuringbalustersarealsoinchannelofrail).Attachwith3self-drillingscrewsprovided.UsethethreeouterholesinRSBtoattachscrews.
24. Slidebalusterspacerupandsnapintotoprail.
Installing Optional Gaskets25. Stairrailgasketsare
designedtofitatslopesof32°to37°.Gasketsarelabeledinordertoensurecorrectlocation.
Attaching Post Caps and Installing Foot Block 26. Securepostcapswith
siliconeorPVCadhesive.Attachfootblockperfootblockinstructions.
NOTE: Clean-up any excess adhesive before it dries.
HOW TO INSTALL STANDARD STAIR RAILING/CONTINUEDTREX TRANSCEND
3
1
202
3
1
21 2
3
3
1
22
1
23
Upper Post Location -
Top Rail
(view from under rail)
(view from under rail)
Lower Post Location -
Top Rail
24
Universal RailStair GasketLocations
STR T2 B1
STR T1 B2
STR T1 B2
STR T2 B1
2
26
3
1
-
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0420
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
7
IMPORTANT NOTES:» Onlyforusewith
pressure-treated4x4post(3.5"nominalsquare)and4"x4"(102mmx102mm)postsleeve.TrexpostmountsorjoistmountpostscannotbeusedwithTrexTranscendstairrailing.CuttingpostandpostsleeveonlyappliestoCocktailstylerailing.
» DO NOT CUT POST/POST SLEEVES UNTIL TOPRAIL IS FULLY INSTALLED. THE DECK BOARD USEDIN TRANSCEND STAIR COCKTAIL RAILING WILLNEED TO TERMINATE AT THE TOP OF THE POST ASSHOWN ABOVE. THE DECK BOARD WILL HAVE TO BEINSTALLED INTO THE SIDE OF THE POST IN THESEAREAS USING 2 APPROPRIATE COMPOSITE DECKINGSCREWS – PRE-DRILLING IS RECOMMENDED.
Installing Pressure-treated Posts, Post Sleeves, and Skirts 1. See instructions on page 3. See notes on page 7 regarding
not cutting post/post sleeve.
Measuring and Cutting Bottom Stair Rail2. See instructions on page 3.
Marking Location for Foot Block on Bottom Rail3. See instructions on page 4.
Attaching RSB’s for Bottom Stair Rail4. See instructions on page 4.
Attaching Bottom (Universal) Stair Rail5. See instructions on page 4.
IMPORTANT NOTE: REMEMBER TO INVERT UNIVERSAL TOP RAIL BEFORE MARKING AND CUTTING
Measuring and cutting Top Stair Rail6. See instructions on page 5.
Measuring and Cutting Deck Board
7. Usingthecuttoprailastemplate,cutdeckboardatupperpostlocationatsameangleasthetoprail.Leaveagenerousamountofdeckboardmaterialatlowerpostlocationasthiswillallowforoverhangandcanbecutlater.
Attaching RSB’s for Top Stair Rail8. See instructions on page 6.
Installing Inverted Top Baluster Spacer and Placing balusters9. See instructions on page 6.
DONOTSLIDETOPBALUSTERSPACERINTOPLACEYET.
Attaching Top Stair Rail10.See instructions on page 6.
Cutting Lower Post/Post Sleeve
11. Cutpostandpostsleevestoproperanglesocutisflushwiththetoprail.Becarefultonotcuttoprail.
Attaching Deck Board to Top Stair Rail and Securing Balusters
12. PlacedeckboardontoprailandattachboardtopostsusingtwoTrexrecommendedcompositedeckingscrews(usetwoscrewspereachpost).
NOTE: At upper post location pre-drilling is recommended and install screws perpendicular to the post.
13. Secureboardtotop(universal)railfromundersideofrailintobottomofdeckboardwith1-5/8"(41mm)pan-headscrews(notprovided) approximatelyevery16".
NOTE: balusters can be shifted out of the way if necessary.
HOW TO INSTALL COCKTAIL STAIR RAILINGTREX TRANSCEND
11Post
Top stair rail
13
16" (41 cm)
16" (41 cm)
1
12
2
7
-
Have Questions? NOTE: Construction methods are always improving. Please ensure you1–800–BUY–TREX have the most up-to-date installation instructions by visiting: trex.com TSR-0920
8
TREX TRANSCEND® STAIR RAILINGInstallation Instructions
HOW TO INSTALL TRADITIONAL STAIR RAILINGTREX TRANSCEND
Installing Pressure-treated Posts, Post Sleeves, and Skirts 1. See instructions on page 3.
Measuring and Cutting Bottom Stair Rail2. See instructions on page 3.
Marking Location for Foot Block on Bottom Rail3. See instructions on page 4.
Attaching RSB’s for Bottom Stair Rail4. See instructions on page 4.
Attaching Bottom (Universal) Stair Rail5. See instructions on page 4.
IMPORTANT NOTE: REMEMBER TO INVERT UNIVERSAL TOP RAIL BEFORE MARKING AND CUTTING
Measuring and cutting Top Stair Rail6. See instructions on page 5.
Measuring and Cutting 2x4
7. Usingthecuttoprailastemplate,cut2x4atsameangleandlengthofthetoprail.
Attaching RSB’s for Top Stair Rail8. See instructions on page 6.
Installing Inverted Top Baluster Spacer and Placing Balusters9. See instructions on page 6.
DONOTSLIDETOPBALUSTERINTOPLACEYET.
Attaching Top Stair Rail10. See instructions on page 6.
Attaching 2x4 to Top Stair Rail and Securing Balusters
11. Pre-drillapilotholeandtoenail2-1/2"(6.4cm)compositedeckscrewateachendof2x4intopostonbacksideofstairrail(sidenotfacingdecking).
12. Secure2x4totop(universal)railfromundersideofrailintobottomof2x4with1-5/8”pan-headscrews(notprovided)approximatelyevery16".
NOTE: Balusters can be shifted out of the way if necessary.
13. Slidebalusterspacerupandsnapintotoprail.
Installing Optional Gaskets 14. See instructions on page 6.
NOTE: top gaskets may have to be trimmed to fi t properly.
Attaching Post Caps and Installing Foot Block15. See instructions on page 6.
14. Slidebalusterspacerupandsnapintotoprail.
Installing Optional Gaskets 15. See instructions on page 6.
NOTE: Top gaskets may have tobe trimmed to fi t properly.
Installing Foot Block
16. See instructions on page 6.
HOW TO INSTALL COCKTAIL STAIR RAILING CONTINUEDTREX TRANSCEND
14
7
1
1132
12
16" (41 cm)
16" (41 cm)
13