Topic1. Thermal Principles€¦ · Thermal Principles 1.1 Introduction to Refrigeration 1.2 Work...
Transcript of Topic1. Thermal Principles€¦ · Thermal Principles 1.1 Introduction to Refrigeration 1.2 Work...
Topic1. Thermal Principles1.1 Introduction to Refrigeration1.2 Work and Heat1.3 Temperature1.4 Pressure1.5 Thermodynamic Properties1.6 Liquid-vapor Properties1.7 Boiling Point1.8 Heat and Enthalpy1.9 Sensible and Latent Heat1.10 Entropy and Isentropic process1.11 General Gas Laws1.12 Thermodynamic Processes1.13 Conservation of mass1.14 Steady-flow energy equation
1
1.15 Heating and cooling1.16 Bernoulli’s equation1.17 Heat transfer1.18 Conduction1.19 Convection1.20 Radiation1.21 Thermal resistance1.22 Cylindrical cross section1.23 Heat exchangers1.24 Thermal Comfort
1.1 Introduction to Refrigeration
2
Refrigeration: the process of achieving and maintaining a temperature of product or space below that of the surroundings
Applications:Food processingFood storageTransportation refrigerationAir conditioningIndustrial processSpecial applications
: the science of moving heat from low temp. to high temp.Ex. Refrigerator, Freezer, Cooler, Ice maker, air conditioner etc.
: milk, ice cream, beverage
: meats, fish, fruits, vegetables, frozen food: bus, truck, train, ship, aircraft
: hospital, hotel, factory, residential AC
: chemical process, laboratories, printing, textile
: ice maker, ice sketch, construction
1.2 Work and Heat
3
Fig1.1 Reversible heat engine E driving a reversible refrigerator (heat pump) P
PW
Cold reservoir, T0
Hot reservoir, T1
E
Q1
Q2
Q1
Q2
The first laws of thermodynamicsWhen work and heat energy are exchanged there is no net gain or loss of energy.
A net flow of heat from the low temp. to the high temp. without any external work input, which is impossible. Wmin = Q2 (T1 –T0)/T0
Coefficient of performance (COP) of P = heat extracted/work input = Q2/W = T0/(T1 –T0)
Carnot Efficiency of E = W/Q1 = (T1 –T0)/T1
T in absolute scale K
Example 1.1: Heat is to be removed at a temperature of -5°C and rejected at a temperature of 35°C.What is the Carnot or Ideal COP?Problem: T0 = -5°C, T1 = 35°C, COPCarnot = ?
Solution: Carnot COP = T0/(T1 –T0) = 268/(308-268) = 6.7
4
1.3 TemperatureTemperature: its thermal state and its ability to exchange energyReference points on Celsius scale: 0C and 100CAbsolute temperature in Kelvin, T = T C + 273 K, T K = T CConversion units: C = (F - 32)/1.8Absolute temperature in Rankine, T = T F + 460 R
104°F86°F68°F50°F32°F14°F-4°F
-22°F-40°F
40°C30°C20°C10°C
0°C-10°C-20°C-30°C-40°C
Fig1.2 Temperature scale
1.4 Pressure
5
Pressure P: the normal force exertedby a fluid per unit areaAbsolute pressure, gauge pressure, standard pressure 101.325 kPaMeasurement device: pressuregauges, manometersPressure units conversionMetric unitsInch-Pound (I-P) units
Fig1.3 Pressure gauges, manometers
Fig1.4 Pressure units conversion
1.5 Thermodynamic Properties
6
Density : the mass occupying a unit volume
Specific volume : the volume occupying a unit mass of air at standard atmospheric pressure and 25C = 1.2 kg/m3
Properties: temperature T, pressure P, density ,specific volume , specific heat cv cp, enthalpy h, entropy s, liquid vapor propertyThermo. properties are not all independently variable.
A substance: two intensive thermodynamic properties define the state
A mixture: three intensive thermodynamic properties define the state, i.e. dry air and water vapor
Example 1.2: What is the mass of air contained in a room of dimensions 4 by 6 by 3 m if the specific volume of the air is 0.83 m3/kg?Problem: mair = ? for a WLH and air
Solution: mair = V/air = W*L*H/air = 4*6*3/0.83 = 72/0.83 = 86.7 kg
1.5 Thermodynamic Properties
7
Specific heat cv and cp: the quantity of energy required to raise the temperature of a unit mass by 1 Kcp is more applies to most of the heating and cooling processesApproximated cp for important substances are constant for small Tcp = 1.00 kJ/kg.K for dry aircp = 4.19 kJ/kg.K for liquid watercp = 1.88 kJ/kg.K for water vapor
Example 1.3: What is the rate of heat input to a water heater if 0.4 kg/s of water enters at 82C and leaves at 93C?Problem: Q = ? to a heater of ሶ𝑚 at Ti and Te
Solution: CV at the water volume1st Law SSSF: Q = W + ሶ𝑚cpTAssume: Boiler W = 0, cp = 4.19 kJ/kg.K for liquid waterQin = ሶ𝑚cpt = 0.4*4.19(93 – 82) = 0.4*46.1 = 18.44 kW
Q = qAs
Fig1.5 Ex1.3 Water heater
1.6 Liquid-vapor Properties
8
Liquid-vapor properties: Most cooling and heating system usesubstances that pass between liquid and vapor states in their cycle.T, P, h, s – Tables or Charts of properties, i.e. P-T, T-s, P-h charts
Figure1.6 Skeleton pressure-enthalpy P-h diagram for water
pressure-enthalpy p-h diagramseparated by saturation line(1) Subcool-liquid region(2) Liquid-vapor region (mixture)(3) Superheated-vapor regionConstant temperature lineWater boils at a higher temp. when the pressure is higher.
Constant T = 100C
T = 50C, P = 12.3 kPa
T = 150C, P = 476 kPa
9
Table of properties10 < T < 40 C; Ps = 0.0051T2 -0.0515T + 1.29 kPa
Saturated liquid for 10 < T < 150 C; hf = 4.19T kJ/kg
Saturated vapor 10 < T < 150 C; hg = 1.75T + 2501 kJ/kg
Superheated vapor at T (C); h = 1.88T-0.13Tsat+ 2501 kJ/kg
Dynamic viscosity of liquid for 10 < T < 150 C; 105 = -0.00018T3-0.044T2-3.4T+ 165 kg/m.s
1.7 Boiling Point
10
Water boils at a higher temp. when the pressure is higher.
Figure1.7 Change of state with pressure and temperature (P-T diagram)
T = 373C, P = 22 MPa
T = 0.01C, P = 0.61 kPa
10 < T < 40 C; Ps = 0.0051T2 -0.0515T + 1.29 kPa
1.8 Heat and Enthalpy
11
Heat - many forms of energy, generated from chemical sources. The heat of a body is its thermal or internal energy. A change in heat - a change of temperature or - a change between the solid, liquid and gaseous states.Enthalpy is the sum of its internal energy and flow work: H = u + Pv
Enthalpy : the amount of heat is the change in enthalpy at constant-pressure process and no work done W = 0Datum plane for water and steam: h = 0 kJ/kg, s = 0 kJ/kgK at 0C but datum plane for refrigerant: h = 200 kJ/kg , s = 1.0 kJ/kgK at 0C then at 100C, hf = 419.06 kJ/kg for liquid water = cpT = 4.19*100,
hg = 2676 kJ/kg for water vaporExample 1.3: Q = ሶ𝑚cpT = ሶ𝑚h, h = cpT for liquid water
1.8 Heat and Enthalpy
12
Example 1.4: A flow rate of 0.06 kg/s of water enters a boiler at 90C, at with temperature the enthalpy is 376.9 kJ/kg. The water leaves as steam at 100C. What is the rate of heat added by the boiler?Problem: a boiler, ሶ𝑚 at Ti (given hi), Te , Q = ?
Solution: CV at the boiler1st Law SSSF: Q = W+ ሶ𝑚hAssume: Boiler W = 0, at 100C, hg = 2676 kJ/kg for sat vaporQin = ሶ𝑚h = 0.06(2676 – 377) = 0.06*2299 = 137.6 kW
Q
m,Ti
Te
Fig1.8 Fire tube boiler
Using function: hf = 4.19T = 4.19*90 = 377 kJ/kghg = 1.75T + 2501 kJ/kg = 2676 kJ/kgQin = ሶ𝑚h = 0.06(2676 – 377) = 137.6 kW
1.9 Sensible and Latent Heat
13
Sensible heat - a change of temperatureQS = 419 kJ/kg for raise water from 273K to 373K (0C to 100C)Latent heat - a change of state (solid to liquid, liquid to gas)QL = 334 kJ/kg for melting ice water at 273K (0C)QL = 2257 kJ/kg for boiling liquid water at 373K (100C)
Fig1.9 Change of temperature (K) and state of water with enthalpy (T-H diagram)
1.9 Sensible and Latent Heat
14
Example 1.5: If 9 kg/s of liquid water at 50C, flow into a boiler, is heated, boiled, and superheated to a temperature of 150C and the entire process takes place at standard atmospheric pressure, what is the rate of heat transfer to the water? Problem: a boiler, m liquid at Ti and superheated vapor Te, at const. 101 kPa, Q = ?
Consist of 3 processes: (1) bringing Ti of subcool water at P to Tsat
(2) converting liquid to vapor at Tsat
(3) Superheating vapor from Tsat to Te
Solution: Boiler Q = ሶ𝑚h T = 50C, hi = 4.19*50 = 210 kJ/kgTe = 150C & Tsat = 100C at 101 kPahe = 1.88Te-0.13Tsat+ 2501 = 2770Q = ሶ𝑚h = 9(2770 – 210) = 23,045 kW
Qm,Ti
Te
Ti Tsat
Tsat Te
Tsat
hi he
Fig1.10 Water tube boiler
1.10 Entropy and Isentropic process
15
Entropy s: If a gas or vapor is compressed or expanded frictionlesslywith Q = 0 during the process, the entropy remains constant,h represents work required by compression or expansion
Isentropic compression: adiabatic and without friction, occurs at constant entropy s1 = s2. Wisen = ሶ𝑚 (h1 – h2) Wactual = ሶ𝑚 (h1 – h2’) > Wisen
Compression efficiency, c = Wisen /Wact
Example 1.6: Compute the power required to compress 1.5 kg/s of saturated water vapor from a pressure of 34 kPa to one of 150 kPa.Problem: W = ? to compress sat. water vapor m from P1 to P2
Solution: CV at compressor; Q = W + ሶ𝑚(h2 – h1), Assume compressor Q = 0h1 = hg@34 kPa = 2630 kJ/kg, s1 = 7.7 kJ/kg.K (p-h diagram)At P2 = 150 kPa, s2 = s1 h2 = 2930kJ/kgW = - ሶ𝑚(h2 – h1) = -1.5*(2930 - 2630) = -450 kW
P1 = 34 kPa
P2 = 150 kPa
h1 h2
16
P1 = 34 kPa
P2 = 150 kPa
h1 = hg@34 kPa
= 2630 kJ/kg
h2 = 2930kJ/kg
Isentropic compression: adiabatic and reversible, s1 = s2
Wisen = m(h1 – h2)
c = Wisen /Wact
2’
1
h2’
1.11 General Gas Laws
17
Perfect-gas law: PV = mRTP = absolute pressure, PaV = volume, m3; m = mass, kg; = density = m/V, kg/m3
R = gas constant = 287 J/kg.K for air and 462 J/kg.K for waterT = absolute temperature, KPerfect-gas equation is applicable to dry air and to highly superheatedwater vapor and not applicable to water and refrigerant vapors close totheir saturation conditions.
Example 1.7: What is the density of dry air at 101 kPa and 25C?Problem: dry air = ? at P and TSolution: Pv = RT, P/ = RT, = P/RTR = 287 J/kg.K for air, T = 25 + 273 = 298 K = P/RT = 101*1000/(287*298)= 1.18 kg/m3
Boyle’s Law: PV = constantCharles’s Law: V/T = constantDalton’s Law: Ptotal =Pi, P = RT
Example 1.8: If dewpoint at 15C for moist air at 101 kPa and 25C, what is the density of dry air?Problem: dry air = ? at Pt , T, Tdp = Tsat
Solution: a = Pa/RaT, Pa = Pt - Ps
Ps = 0.0051T2dp -0.0515Tdp + 1.29 = 1.67 kPa,
Pa = 101 – 1.67 = 99.34 kPaa = Pa/RaT = 1.20 kg/m3
w = Ps/RsT = 1.67/(462*298) = 0.0125 kg/m3
v = 1/w = 79.9 m3/kg > vsat@15C = 77.9
1.12 Thermodynamic Processes
18
Heating and cooling = thermodynamic processesEnergy is the central concept. Energy analysis is fundamental procedure in thermodynamics.System – object consideredControl volume – specified region in spaceSystem boundary (control surface) – encloses the control volumeSize and shape of the system are specified for simplify accounting for the change in energy storage within the system or energy transfers across a system boundary.Environment – not included in system
Problem: consider a pump or an entire buildingStep 1: Problem definitionStep 2: Schematic System (change in energy storage) ,
System boundary (energy transfers across)Step 3: Assumptions steady state, steady flow, no heat loss e.t.c.Step 4: Physical law mass conservation, energy balance (1st law thermo.)
1.13 Conservation of mass
19
Mass is neither crested nor destroyed in the process analyzed.Mass may be stored within a system or transferred between a system and its environment, but it must be accounted for in any analysis procedure.mt + m1 = mt+t + m2
Dividing by t: m1/t = (mt+t - mt)/t + m2/t
ሶ𝑚1 = m/t + ሶ𝑚2
If the rate of change of mass within the system is zero m/t = 0 ሶ𝑚1 = ሶ𝑚2 = ሶ𝑚 steady flow ሶ𝑚 = mass flow rate, kg/s
Newton’s second law: Force = ma = m(dV/dt)m = mass, kga = acceleration, m/s2
V = velocity, m/st = time, s
Fig1.11 Flow system for conservation of mass
1.14 Steady-flow energy equation
20
ሶ𝑚(h1 + V21/2 +gz1) + Q - ሶ𝑚(h2 + V2
2/2 +gz2) – W = dE/dtz = elevation, mg = gravitational acceleration = 9.81 m/s2
Q = rate of heat transfer in form of heat, WW = rate of heat transfer in form of work, WE = energy in system, J
dE/dt = 0 for steady flow process ሶ𝑚(h1 + v2
1/2 +gz1) + Q = ሶ𝑚(h2 + v22/2 +gz2) + W
Often V2/2 and gz is negligible compare to h, W or Qሶ𝑚h1 + Q = ሶ𝑚h2 + W
Q – W = ሶ𝑚(h2 - h1)
Fig1.12 Energy balance on a control volume
1.15 Heating and cooling
21
steady flow process: Q – W = ሶ𝑚(h2 - h1)If W = 0 by a pump, compressor or engine: Q = ሶ𝑚(h2 – h1)
Example 1.9: Water flowing at a steady rate of 1.2 kg/s is to be chilledfrom 10 to 4C to supply a cooling coil in an air-conditioning system.Determine the necessary rate of heat transfer.Problem:water low ሶ𝑚 chilled steadily from T1 to T2 , Q = ? Solution: CV water in shell Q = ሶ𝑚(h2 – h1) h2 = 4.19*4 = 16.8 kJ/kgh1 = 4.19*10 = 41.9 kJ/kg Q = ሶ𝑚(h2 – h1) Q = 1.2*(16.8 - 41.9) = -30.2 kWLiquid water Q = ሶ𝑚cp(T2 – T1) = -30.2 kW
Adiabatic processes - no heat is transferred; Q = 0-The walls of the system are thermally insulated.-The throughput rates of energy are large in relation to the energytransmitted to or from the environment in the form of heat.
T2ሶ𝑚, T1
Q
Fig1.13 Liquid chiller
1.16 Bernoulli’s equation
22
Bernoulli’s equation : derived from mechanical behavior of fluids,But it is also derivable as a special case of the energy equation through second-law considerations: Tds = du +Pdv –(1) (Gibb’s equation)
For adiabatic process Q = 0, and no mechanical work W = 0:
h + V2/2 +gz = const
Differentiation yields: dh + VdV + gdz = 0 –(2)
Enthalpy, h = u + Pv is differentiated to yield dh = du + Pdv + vdP –(3)
Combining eq (1) and (3) results in: Tds = dh – vdP
For an isentropic process (adiabatic+ no friction): ds = 0 = dh – vdPSubstituting dh = vdP = dP/ into eq.(2) dP/ + VdV + gdz = 0
For constant density, integrates to the Bernoulli equation:
P/ + V2/2 +gz = const
Bernoulli equation shall be used for liquid and gas flow in which the
density varies only slightly and may be treated as incompressible.
1.16 Bernoulli’s equation
23
Example 1.10: Water is pumped from a chiller in the basement, where z1 = 0 m to a cooling coil located on the twentieth floor of a building, where z1 = 80 m. What is the minimum pressure rise the pump must be capable of providing if the temperature of the water is 4C.Problem: water pumped from z1 to z2 at T, P (Pa) = ? Solution: ignore friction loss in pipe using Bernoulli equation; P1/ + V2
1/2 +gz1 = P2/ + V22/2 +gz2
Assume V1 = V2, @4C = 1000 kg/m3
P1 - P2 = g(z2 - z1) = 1000*9.81*(80 – 0) = 785000 Pa = 785 kPa
Fig1.14 water pipe
Modified Bernoulli’s equation
24
Example 1.11: Compute the pressure drop when 3.0 L/s of 4C water flows through a steel pipe with a nominal diameter of 50 mm (ID = 52.5 mm) that is 20 m long in horizontal and 80 m long in vertical with minor loss Leq = 0.2Ltotal.Problem: water flow ሶ𝑉 at T, pipe D and L pumped from z2 - z1, P (Pa) = ? Solution: pressure drop include major and minor loss in pipe L+Leq=1.2Ltot=120 mP1/ + V2
1/2 +gz1 = P2/ + V22/2 +gz2 + Ploss, Ploss = f(L/D)V2/2,
Assume smooth tube f = 0.184Re-0.2, Re = VD/, Water 4C, @4C = 1000 kg/m3,105 = -0.00018T3-0.044T2-3.4T+ 165 = 150 kg/ms →= 150 10-5 kg/msV = ሶ𝑉/((ID)2/4) = 1.386 m/s, Re = 1000*1.386(0.0525)/0.0015 = 48513, f = 0.184Re-0.2 = 0.02126, Ploss = 0.02126(120/0.0525)1000*1.3862/2 = 46.7 kPaP1 - P2 = g(z2 - z1) + Ploss = 1000*9.81*(80 – 0) + 46.7 kPa = 831 kPa
P1/ + V21/2 +gz1 = P2/ + V2
2/2 +gz2 + Ploss
Pressure loss in pipe; Ploss = f(L/D)V2/2, smooth tube for turbulent flow Re > 10,000; f = 0.184Re-0.2
Re = VD/Dynamic viscosity of liquid water for 10 < T < 150 C; 105 = -0.00018T3-0.044T2-3.4T+ 165 kg/m.s
1.17 Heat transfer
25
Heat transfer analysis s developed from thermodynamics laws of conservation of mass and energy, the second law of thermodynamics, and three rate equations describing conduction, convection and radiation.
1. Conduction: Direct from one body touching the other, or through a continuous mass2. Convection: By mean of a heat-conveying fluid moving between one and the other.3. Radiation: Mainly by infrared waves (but also in a visible band, e.g. solar radiation), which are independent of contact or an intermediate fluid.
26
1.18 ConductionFourier’s law of heat conduction (1822):Qcond = -kAT/L = -(k/L)ATA = cross-sectional area, m2, L = x = length, mT = temperature difference = T2 - T1, K or Ck = thermal conductivity, W/m.K – characteristic of the materialk/L conductance
Thermal conductivity and rate of conductive heat transfer is related to
the molecular structure of materials.
rate of heat transfer in differential form: Qcond = -kA(dT/dx)Table1.1 Thermal conductivity of some materials
xx
T1
T2
Td𝑇d𝑥
ሶ𝑄𝑐𝑜𝑛𝑑
A
1.19 Convection
27
Newton (1701): Qconv = hcA(Ts – Tf)Ts = surface temperature, CTf = fluid temperature, Chc = convection coefficient, W/m2.K- widely used in engineering- Essence of convective heat transfer analysis is the evaluation of hc
hc = function of (flow velocity, fluid properties, geometry of the surface)in flow over plan surface, in pipes and ducts, and across tubes
Extensive theory has been developed to support the experimentally
observed correlations and to extend them to predict behavior in untested flow configurations.
It is the correlations rather than the theories used in practical
engineering analysis.
Dimensionless analysis: basis of most of the pertinent correlations
Hot iron block Ts = 400 C
Tf = 15 C
Vair = 0
Ts
T=Tair
T(y)
T
ሶQ𝐜𝐨𝐧𝐝
Thermal boundary layer
d𝑇
d𝑦
ሶ𝑞 = −k d𝑇d𝑦Vair = 3 m/s
ሶQconv
ሶ𝑞 = hcT
1.19 Convection
28
Dimensionless parameters: understanding the physical phenomena involved and ability to construct reasonable models for basic flow Reynold number Re = VD/ or VL/Prandtl number Pr = cp/kNusselt number Nu = hcD/k or hcL/kGrafshop number Gr = RaPr = g2x3T/2
Flow Correlation: Nu = C(Ren)(Prm)
C, n and m = determined experimentally
Fig 1.15 Correlation for forced convection in smooth tubes, turbulent flow
Nu = 0.023Re0.8Pr0.4
→ Forced convection, inertia/viscous→ Fluid properties, momentum/thermal diffusion→ Convection/conduction→ Natural convection
29
Nusselt number of flow in circular tubes
30
Boiling and condensation heat transfer
1.20 Radiation
31
Radiant-energy transfer results when protons emitted from one surface travel to other surfaces, then either absorbed, reflected, or transmitted through the surfaces.
Emissive power: E = T4 Stefan–Boltzmann law = 5.669 10−8 W/m2 · K4 = Stefan–Boltzmann constantT = Absolute temperature, K = emissivity, = 1 for a black body
In many real materials, emissivity = absorptivity, = → as gray bodies
Radiation leaving a surface is distributed uniformly in all direction →
the geometry relationship between two surfaces affects the radiant-energy exchange between them. → shape factor FA
If F expresses effects of emissivity, absorptivity, reflectivity,
transmissivity, and rate of radiant heat transfer of the surfaces,
The radiant heat exchange: Qrad = AFFA(T41- T4
2)
1.21 Thermal resistance
32
Qcond = -(k/L)AT
Qconv = hcAT
Qrad = AFFA(T41- T4
2)
Qrad hrAT --linearized equation, where hr = FFA(T41- T4
2)/(T1- T2)
Ohm’s law: I = E/R, Current = Potential difference/Resistance
Analogy to Ohm’s law: Q = T/RT , RT = thermal resistance
Qcond = -T /(L/kA), RT,cond = L/(kA)
Qconv = T/(1/hcA), RT,conv = 1/(hcA)
Qrad T/(1/hrA), RT,rad = 1/(hrA)
→ Qcond linear with temperature
→ Qconv linear with temperature
→ Qrad non-linear with temperature
T1 T2
T1 T2
RT = Rs1+RA+1/(1/RB+1/RC)+RD+RS2
Q = (T2-T1)/RT
1D steady state heat transfer through buildings
qin = (qconv,o + qrad,o) = (qconv,i + qrad,i)
qin = ho(To - Tw,o) = hi(Tw,i - Ti)
ho, hi = inner, outer surfaceconductances, account both convection and radiation heat transfers
1.21 Thermal resistance
34
Q = (Ti – To)/Rtot = UA(Ti – To)U = overall heat coefficient, W/m2.KUA = 1/Rtot, U = 1/(RtotA)RA = L/k = Rw – conduction through wallRA = 1/(hc + hr) = Rs --surface
1.22 Cylindrical cross section
35
T2T1
r2
T2
h1
h2
T3T2
Rcomb
kins
Find Rcyl by Qcond = -kArdT/dr
r1r2(Qcond/(2rL))dr = T1
T2(-k)dT
Qcond = -(T2–T1)[2Lk/(ln(r2/r1))]
Rcyl = ln(r2/r1)/(2Lk)
Rcyl = ln(ro/ri)/(2Lk) x/(Amk)
x/(Amk) = (ro - ri)/(2Lk(ro + ri)/2)
= [2(ro - ri)/(ro + ri)]/(2Lk)
For thin tube x = ro - r1;
ln(ro/ri) 2(ro - ri)/(ro + ri) (< 0.1%)
Rcyl x/(Amk)
for thin copper tubes and steel pipes
1.23 Heat exchangers
36
A device in which energy is transferred from one fluid stream to another across a solid surface.Be used extensively in refrigeration and air conditioningQ = UA(LMTD), UA = 1/Rtot
Since the temperature of one or both fluids may vary as they flow through the heat exchanger, mean temperature difference - determinedLMTD = Tlm = (TA - TB)/[ln(TA/TB)]T1 = temperature difference between two fluids at position A, CT2 = temperature difference between two fluids at position B, C
T1 T2
1.23 Heat exchangers
37
Example 1.13: Determine the heat transfer rate of the shell and tube heat exchanger: h1 = 50W/m2.K, h2 = 80W/m2.K, T1,i = 60C, T1,o = 40C, T2,i = 20C, T2,o = 30C, ro = 11 mm, ri = 10 mm, length = 1 m, and for the metal k = 386 W/m.K, Problem: [CF HX,1 in shell, 2 in tube] Q = ? h1, h2, T1,i, T1,e, T2,i, T2,o, ro, ri, L, k Solution: Q = UATlm = Tlm/Rtot
Tlm = (TA - TB)/[ln(TA/TB)],Rtot = 1/(h1A1)+ln(ro/ri)/(2Lk)+1/(h2A2)
A1= 2roL = 2(0.011)(1) = 0.069 m2
A2= 2riL = 2(0.011)(1) = 0.063 m2
Rtot =1/(50*0.069)+ln(11/10)/(2*1*386)+1/(80*0.063)=0.289+0.00004+0.199=0.487W/K
TA = T1,o – T2,I = 40 – 20 = 20CTB = T1,i – T2,o = 60 – 30 = 30CTlm = (30-20)/[ln(30/20)]=24.7CQ = 24.7/0.487 = 50.7 W
1.23 Heat exchangers
38
Fig 1.16 Temperature change.
(a) Refrigerant cooling fluid. (b) Fluid cooling refrigerant. (c) Two fluids.
Tlm = (Tmax – Tmin)/[ln(Tmax/Tmin)]
Example 1.14: A fluid evaporates at 3C and cools water from 11.5C to 6.4 C. What is the logarithmic mean temperature difference and what is the heat transfer if it has a surface area of 420 m2 and the thermal transmittance is 110 W/m2K? Problem: Evaporator As and U at TR and cools water from Ti to To ,Q = ? Solution: Q = UATlm , Tlm = (TA - TB)/[ln(TA/TB)]Tmax = Ti – TR = 11.5 – 3 = 8.5C, Tmin = To – TR = 6.4 – 3 = 3.4CTlm = (8.5-3.4)/[ln(8.5/3.4)]=5.566CQ = 110*420*5.566 = 257000 W = 257 kW
39
1.24 Thermal Comfort
40-500 W/m2
30 – 70 %RH
Fresh air 8 – 15 L/s3 – 7 m/min
23 - 31 C
Temperature difference < 3C between head and foot levels
Skin temp., tskin 33.7C
tcore < 31C→ Lethal/deadlytcore 35C → Slight discomforttcore 36.8Ctcore 39C → Slight discomforttcore > 43C → Lethal/deadly
1.24 Thermal Comfort
A living human body as a heat engineConsumes food → metabolism → heat and work
Generates heat at a rate 100 – 2000 W100 W → sedentary person, sitting2000 W → strenuous exercise
Qgenerate = Qskin + Qrespiration + Qstore
Qgenerate M = c*met* As,naked
met = 58.2 W/m2
As,naked = 0.202mass0.425height0.725