04/21/23 Righter Group, Inc. 1

Tnemec StranlockRevêtements Renforcies

Présente

04/21/23 Righter Group, Inc. 2

STRANLOK 273

Système Murale àl’époxy renforci avec Fibre de Verre

Avantages :

•Sans odeur – 100% Solide

•Haute résistance au choc thermique

•Utilisé dans les Hospitaux, Pharmaceutique, Aliments

•Système plus rapide pour installation

04/21/23 Righter Group, Inc. 3

04/21/23 Righter Group, Inc. 4

04/21/23 Righter Group, Inc. 5

04/21/23 Righter Group, Inc. 6

04/21/23 Righter Group, Inc. 7

04/21/23 Righter Group, Inc. 8

04/21/23 Righter Group, Inc. 9

04/21/23 Righter Group, Inc. 10

04/21/23 Righter Group, Inc. 11

04/21/23 Righter Group, Inc. 12

04/21/23 Righter Group, Inc. 13

04/21/23 Righter Group, Inc. 14

04/21/23 Righter Group, Inc. 15

04/21/23 Righter Group, Inc. 16

04/21/23 Righter Group, Inc. 17

04/21/23 Righter Group, Inc. 18

04/21/23 Righter Group, Inc. 19

04/21/23 Righter Group, Inc. 20

04/21/23 Righter Group, Inc. 21

04/21/23 Righter Group, Inc. 22

04/21/23 Righter Group, Inc. 23

04/21/23 Righter Group, Inc. 24

04/21/23 Righter Group, Inc. 25

04/21/23 Righter Group, Inc. 26

04/21/23 Righter Group, Inc. 27

04/21/23 Righter Group, Inc. 28

04/21/23 Righter Group, Inc. 29

04/21/23 Righter Group, Inc. 30

04/21/23 Righter Group, Inc. 31

04/21/23 Righter Group, Inc. 32

04/21/23 Righter Group, Inc. 33

04/21/23 Righter Group, Inc. 34

04/21/23 Righter Group, Inc. 35

04/21/23 Righter Group, Inc. 36

04/21/23 Righter Group, Inc. 37

04/21/23 Righter Group, Inc. 38

04/21/23 Righter Group, Inc. 39

04/21/23 Righter Group, Inc. 40

04/21/23 Righter Group, Inc. 41

04/21/23 Righter Group, Inc. 42

04/21/23 Righter Group, Inc. 43

SECTION 09800 – SPECIAL COATINGS  

FIBERGLASS REINFORCED EPOXY GLAZE   Substrate: Cement Board/CMU (High Impact Drywall* Qualified) Prime Coat: Series 201 Epoxoprime applied by roller to 150 sq. ft. per gallon. Base Coat**: Series 218 Mortar Clad applied to achieve a filled, smooth surface approximately 1/16 inch.

Fiberglass joint tape to be embedded with 218 Series. IntermediateBedding Coat: Series 280 Tneme-Glaze applied at a rate of 125 sq. ft. per gallon (10.0 mils) into the wet film imbed Series

273 Fiberglass Mat. Overlap and double cut seams, smoothing the mat to saturation with additional 280 Tneme-Glaze of 4-6 mils.

 IntermediateFilling Coat: Series 280 Tneme-Glaze applied at a rate of 150 sq. ft. per gallon (10.0 mils). 

Following cure, sand the surfaces to remove any raised fiber and or excess material. Finish Coat:Option #1: Series 475 Tnemec Titan applied to achieve 2.0 - 3.0 mils dry film thickness. Option #2: Series 290 CRU Urethane applied at 2.0 – 3.0 mils DFT (use for high stain environments) Color as selected by owner. * The use of Gypsum substrates may compromise ultimate performance of the coating system in high impact and high moisture

environments. ** For use when cement board and CMU are specified.