Bitte decken Sie die schraffierte Fläche mit einem Bild ab.

Please cover the shaded area with a picture.

(24,4 x 11,0 cm)

Tire removal and installation instruction using a manual tire changer.

I B&S TIS

Version 1.5

Public

Contents

Tire mounting with manual tire changer 1

Tire dismounting with manual tire changer 2

2 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Position the sensor opposite to the

mounting head

Don’t position the sensor at other location

because it may be hit by the tire

1. Fix the rim in the tire changer

180°

Sensor

Sensor

Mounting head

Mounting head

3 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

If the tire slides the correct sensor position is

lost and the tire can hit the sensor

2. Mount the lower bead

Mount the lower bead making sure that the

tire does not slide

Example marking to

indicate the sensor

position before

mounting

Example marking to

indicate the sensor

position before

mounting

At the end of the

mounting the marking

and the sensor position

match => No sliding of

the tire occurred

At the end of the

mounting the marking

and the sensor position

don’t match => Sliding

of the tire occurred

Sensor

Sensor Sensor

Sensor

Mounting head

Mounting head

Mounting head Mounting head

4 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Don’t position the sensor at any other

location because it may be hit by the tire

3. Position the sensor for the upper bead mounting

Position the sensor opposite to the

mounting head

180°

Sensor

Sensor

Mounting head

Mounting head

5 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

If the tire slides the correct sensor position is

lost and the tire may hit the sensor

4. Mount the upper bead

Mount the upper bead making sure that the

tire does not slide

Example marking to

indicate the sensor

position before

mounting

At the end of the

mounting the marking

and the valve match =>

No sliding of the tire

occurred

At the end of the

mounting the marking

and the valve don’t

match => Sliding of the

tire occurred

Example marking to

indicate the sensor

position before

mounting

Sensor

Sensor

Sensor

Sensor

Mounting head Mounting head

Mounting head Mounting head

6 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Contents

Tire mounting with manual tire changer 1

Tire dismounting with manual tire changer 2

7 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Don’t position the bead breaker at the sensor

position as it may be damaged

1. Break the bead on the front side

Position the bead breaker on the opposite

side of the sensor

Sensor Sensor

8 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Position the bead breaker on the opposite

side of the sensor

Don’t position the bead breaker at the sensor

position as it may be damaged

2. Break the bead on the rear side

Sensor Sensor

9 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Don’t position the sensor at any other

location because it may be hit by the tire

3. Fix the wheel in the tire changer

Position the sensor under the mounting

head

Sensor

Sensor

Mounting head Mounting head

10 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

4. Insert the mounting lever

Insert the mounting lever without touching

the sensor

11 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

5. Dismount the upper bead

Dismount the upper bead

12 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

Don’t position the sensor at any other

location because it may be hit by the tire

6. Position the sensor for the lower bead dismounting

Position the sensor under the mounting

head

Mounting head Mounting head

Sensor

Sensor

13 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

If the sensor is not under the mounting head

it can be caught by the tire

7. Insert the mounting lever

Insert the mounting lever only if the sensor

is under the mounting head

View from the rear-bottom

of the mounting machine.

As the sensor is at the

right position (under the

mounting head) it is not

touched by the tire.

View from the rear-bottom

of the mounting machine.

As the sensor is not at

the right position (under

the mounting head) it is

caught by the tire.

Mounting head

Mounting head

Mounting head

Mounting head

Sensor

Sensor

Sensor Sensor

14 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D

Public

8. Dismount the lower bead

Dismount the lower bead

15 © Continental AG I May 2015 I Version 1.5 rev NAFTA

Part No. V06216TG1D