The sizing diagram will be available later on! For sizing ... Archive/Air handling units/GOLD...

86

GOLD

www.swegon.comWe reserve the right to alter specifications. 20110601

GOLD PX, plate heat exchanger, size 04

Min. and Max. AirflowsThe flows specified refer to those that can be preset in the hand-held micro terminal. The practical flow limits are deter-mined by the external pressure drop.

Correction factors KOK , dB

Sizing, Installation, Dimensions and Weights

* The integral attenuation of filters and plate heat exchanger has been taken into account. ** Total sound power level emitted to the surroundings is calcu-lated as the sum of the levels in the supply air and the extract air.

Range in the

diagram

Octave band, No. / mid-frequency, Hz

Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -1 -6 -6 -8 -7 -7 -12 -152 -1 -5 -8 -8 -7 -9 -13 -163 -1 -2 -6 -15 -14 -16 -22 -254 -2 -3 -5 -13 -13 -14 -20 -25

To inlet duct* 1 -8 -15 -16 -28 -35 -38 -40 -382 -9 -16 -21 -24 -33 -36 -39 -393 -6 -4 -14 -27 -35 -39 -44 -434 -9 -11 -16 -28 -38 -41 -44 -44

To air handling unit surroun-dings**

1 -12 -20 -29 -29 -40 -40 -46 -462 -12 -19 -31 -29 -40 -42 -47 -473 -12 -16 -29 -36 -47 -49 -56 -564 -13 -17 -28 -34 -46 -47 -54 -56

Size Min. airflow (on airflow regulation)

Max. airflow

m3/h m3/s m3/h m3/s04 288 0.08 1620 0.45

Recommended working range for commissioning.Permissible operating range when the fan is controlled to operate at a lower speed. The lower limit for the airflow when the unit is operat-ing in the airflow regulation mode; see the black broken line in the diagram. If pressure regulation is used, the airflow can be regulated to zero, however this presupposes a certain static pressure drop in the ducting (approx. 50 Pa).

The sizing diagram will be available later on!For sizing, see the ProUnit air handling unit selection

program.

87

GOLD

GO

LD




Size A B C D F G H L Ø Weight, kg

04 800 825 240 345 230 460 920 2000 315 291-337

Power connection1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A

Rated data per fanMotor shaft power: 0.8 kW (0.41 kW)* motor control system, 1 x 230 V, 50 Hz *The motor control system limits the power of the take-off to the value specified.

Clear Space for InspectionA clear space of 1,000 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood.

Right-hand version

Left-hand version

Delivery and Transport within the SiteThe GOLD PX 04 is produced in one single variant. All of its components are arranged at their given physical locations inside the air handling unit.

The electrical equipment cubicle and the drain pipe on the front of the air handling unit can be removed, if required, for trans-porting the unit within the building site.

Base frame/BaseThe GOLD PX 04 is supplied on a base frame with integrated openings for the forks of a fork-lift truck.

The stand is available as an accessory.

Installation/duct connection optionsA: Specify right-hand or left-hand version when ordering!

Outside air Supply air Extract air Exhaust air

Power connection

5252

32 32

80

180

80

50 50

16 52*

* The air handling unit is supplied without end connection panel if a duct accessory housed in an insulated casing will be connected.

88

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -1 -6 -6 -8 -7 -7 -12 -152 -1 -5 -8 -8 -7 -9 -13 -163 -1 -2 -6 -15 -14 -16 -22 -254 -2 -3 -5 -13 -13 -14 -20 -25

To inlet duct* 1 -8 -15 -16 -28 -35 -38 -40 -382 -9 -16 -21 -24 -33 -36 -39 -393 -6 -4 -14 -27 -35 -39 -44 -434 -9 -11 -16 -28 -38 -41 -44 -44


1 -12 -20 -29 -29 -40 -40 -46 -462 -12 -19 -31 -29 -40 -42 -47 -473 -12 -16 -29 -36 -47 -49 -56 -564 -13 -17 -28 -34 -46 -47 -54 -56


Max. airflow

m3/h m3/s m3/h m3/s05 288 0.08 2340 0.65



program.

89

GOLD

GO

LD





Delivery and Transport within the SiteThe GOLD PX 05 is produced in one single variant, in which all the components are arranged at their given physical locations inside the air handling unit.

The electrical equipment cubicle and the drain pipe on the front of the air handling unit can be removed, if required, for transporting the unit within the building site.

Base frame/BaseThe GOLD PX 05 is supplied on a base frame with integrated open-ings for the forks of a fork-lift truck.



Power connection

5252

32 32

80

180

80

50 50

16 52*


05 800 825 240 345 230 460 920 2000 315 291-337


Right-hand version

Left-hand version


Power connection1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A (capacity variant 1) alt. 16 A (capacity variant 2) or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A

Rated data per fanMotor shaft power: 0.8 kW alt. 1.15 kW, motor control system: 1 x 230 V, 50 Hz

90

GOLD



Min. and max. airflowsThe flows specified refer to those that can be preset in the hand-held micro terminal. The practical flow limits are deter-mined by the external pressure drop.

Correction factors, KOK , dB.

Sizing, installation, dimensions and weights

* The integral attenuation of filters and plate heat exchanger has been taken into account.** Total sound power level emitted to the surroundings is calculated as the sum of the levels in the supply air and the extract air.

Rangein

diagram

Octave band, no./mid-frequency, Hz

Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To the outletduct

1 -1 -6 -6 -8 -7 -7 -12 -152 -1 -5 -8 -8 -7 -9 -13 -163 -1 -2 -6 -15 -14 -16 -22 -254 -2 -3 -5 -13 -13 -14 -20 -25

To the inletduct*

1 -8 -15 -16 -28 -35 -38 -40 -382 -9 -16 -21 -24 -33 -36 -39 -393 -6 -4 -14 -27 -35 -39 -44 -434 -9 -11 -16 -28 -38 -41 -44 -44

To unit’s surroundings**

1 -12 -20 -29 -29 -40 -40 -46 -462 -12 -19 -31 -29 -40 -42 -47 -473 -12 -16 -29 -36 -47 -49 -56 -564 -13 -17 -28 -34 -46 -47 -54 -56

Size Min. airflow (for airflow regulation)

Max. airflow

m3/h m3/s m3/h m3/s07 288 0.08 2700 0.75

Recommended working range for sizing.

Permissible operating range when the fan is controlled to operate at a lower speed. The black broken line in the diagram indicates the lower limit for the airflow when the unit is operating in the airflow regulation mode. If pressure regulation is used, the airflow can be regulated to zero, however this presupposes a certain static pressure drop in the ducting (approx. 50 Pa).


program.

91

GOLD

GO

LD





07 915 995 277.5 440 271 543 1085 2230 400 360-419

Power connectionCapacity variant 1: 1-phase, 3-conductor, 230 V -10/+15%, 50 Hz, 10 A or 3-phase, 5-conductor, 400 V -10/+15%, 50 Hz, 10 A

Capacity variant 2: 1-phase, 3-conductor, 230 V -10/+15%, 50 Hz, 16 A or

3-phase, 5-conductor, 400 V -10/+15%, 50 Hz, 10 A

Rated data per fanCapacity variant 1: Motor shaft power: 0.8 kW, motor control system: 1 x 230 V, 50 Hz

Capacity variant 2: Motor shaft power: 1.15 kW, motor control system: 1 x 230 V, 50 Hz

Clear space for inspectionA clear space of 1,000 mm should be provided in front of the unit and at least 200 mm should be provided above the junction hood.

Delivery and transport within the siteThe GOLD PX 07 is produced in one single variant. All of its components are arranged at their given physical locations inside the air handling unit.


Base frame/BaseThe GOLD PX 07 is supplied on a base frame with integrated openings for the forks of a fork-lift truck.


Installation/duct connection optionsA: Specify right-hand or left-hand version when ordering.

Power connection

5252

32 32

80

180

80

50 50

16 52*


Right-hand version

Left-hand version

Outdoor air Supply air Extract air Exhaust air

92

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -1 -6 -6 -8 -7 -7 -12 -152 -1 -5 -8 -8 -7 -9 -13 -163 -1 -2 -6 -15 -14 -16 -22 -254 -2 -3 -5 -13 -13 -14 -20 -25

To inlet duct* 1 -8 -15 -16 -28 -35 -38 -40 -382 -9 -16 -21 -24 -33 -36 -39 -393 -6 -4 -14 -27 -35 -39 -44 -434 -9 -11 -16 -28 -38 -41 -44 -44


1 -12 -20 -29 -29 -40 -40 -46 -462 -12 -19 -31 -29 -40 -42 -47 -473 -12 -16 -29 -36 -47 -49 -56 -564 -13 -17 -28 -34 -46 -47 -54 -56


Max. airflow

m3/h m3/s m3/h m3/s08 720 0.20 3600 1.00



program.

93

GOLD

GO

LD





08 915 995 277,5 440 271 543 1085 2230 400 369-428


Delivery and Transport within the SiteThe GOLD PX 08 is produced in one single variant. All of its com-ponents are arranged at their given physical locations inside the air handling unit.


Base frame/BaseThe GOLD PX 08 is supplied on a base frame with integrated open-ings for the forks of a fork-lift truck.



Power connection

5252

32 32

80

180

80

50 50

16 52*


Right-hand version

Left-hand version


Power connectionCapacity variant 1: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 16 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A Capacity variant 2: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A Rated data per fanCapacity variant 1: Motor shaft power: 1.15 kW, motor control system: 1 x 230 V, 50 Hz Capacity variant 2: Motor shaft power: 1.6 kW, motor control system: 3 x 400 V, 50 Hz

94

GOLD







Rangein

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To the outletduct

1 -1 -6 -6 -8 -7 -7 -12 -152 -1 -5 -8 -8 -7 -9 -13 -163 -1 -2 -6 -15 -14 -16 -22 -25

To the inletduct*

1 -8 -15 -16 -28 -35 -38 -40 -382 -9 -16 -21 -24 -33 -36 -39 -393 -6 -4 -14 -27 -35 -39 -44 -43

To unit’s surroundings**

1 -12 -20 -29 -29 -40 -40 -46 -462 -12 -19 -31 -29 -40 -42 -47 -473 -12 -16 -29 -36 -47 -49 -56 -56

Size Min. flow (for airflow regulation)

Max. airflow

m3/h m3/s m3/h m3/s11 720 0.20 3960 1.10

Recommended working range for sizing.Permissible operating range when the fan is controlled to operate at a lower speed. The black broken line in the diagram indicates the lower limit for the airflow when the unit is operating in the airflow regulation mode. If pressure regulation is used, the airflow can be regulated to zero, however this presupposes a certain static pressure drop in the ducting (approx. 50 Pa).

The sizing diagram will be specified later on!For sizing, see the ProUnit air handling unit selection

program.

95

GOLD

GO

LD


D

E E 5252

16 52*

50 J

K

50 50J

K

8050



Power connection

Delivery and transport within the siteThe GOLD PX 11 is produced in one single variant. All of its components are arranged at their given physical loca-tions inside the air handling unit.

The GOLD PX 11 is always supplied as one unit. The air handling unit can be split into three sections to facilitate transporting it within the building site.

The three sections are joined together by bolts and the electrical and control cables between the sections have quick-fit connectors.

The air handling unit is delivered on wooden beams.


Duct connection optionsA: Specify right-hand or left-hand version when ordering.

Right-hand version

Left-hand version


Size A B C D E F G H J K L Ø Weight, kg

11 655 1199 324 1200 397 324 647 1295 935 551 2510 500 552-646

Power connectionCapacity variant 1: 1-phase, 3-conductor, 230 V -10/+15%, 50 Hz, 16 A or

3-phase, 5-conductor, 400 V -10/+15%, 50 Hz, 10 A Capacity variant 2: 3-phase, 5-conductor, 400 V -10/+15%, 50 Hz, 10 A Rated data per fanCapacity variant 1: Motor shaft power: 1.15 kW,

motor control system: 1 x 230 V, 50 Hz Capacity variant 2: Motor shaft power: 1.6 kW, motor control system: 3 x 400 V, 50 Hz

The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 141-167 kg, D = 270-312 kg.

Division into sections for transport

A AD + 19 mm

If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accessories) can be used for this purpose.* The air handling unit is supplied without end connection panel if a duct accessory housed in an insulated casing will be connected.

Clear space for inspectionA clear space of 900 mm should be provided in front of the unit and at least 200 mm should be provided above the junction hood.

96

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -1 -6 -6 -8 -7 -7 -12 -152 -1 -5 -8 -8 -7 -9 -13 -163 -1 -2 -6 -15 -14 -16 -22 -25

To inlet duct* 1 -8 -15 -16 -28 -35 -38 -40 -382 -9 -16 -21 -24 -33 -36 -39 -393 -6 -4 -14 -27 -35 -39 -44 -43


1 -12 -20 -29 -29 -40 -40 -46 -462 -12 -19 -31 -29 -40 -42 -47 -473 -12 -16 -29 -36 -47 -49 -56 -56


Max. airflow

m3/h m3/s m3/h m3/s12 720 0.20 5040 1.40



program.

97

GOLD

GO

LD


D

E E 5252

16 52*

50 J

K

50 50J

K

8050



Power connection

Delivery and Transport within the SiteThe GOLD PX 12 is produced in one single variant. All of its components are arranged at their given physical locations inside the air handling unit.

The GOLD PX 12 is always supplied as one unit. The air handling unit can be split into three sections to facilitate transporting it within the building site.

The three sections are joined together by bolts and the electri-cal and control cables have quick connectors.



Duct connection optionsA: Specify right-hand or left-hand version when ordering!

Right-hand version

Left-hand version


Size A B C D E F G H J K L Ø Weight, kg

12 655 1199 324 1200 397 324 647 1295 935 551 2510 500 574-668


A AD + 19 mm

If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accessories) can be used for this purpose.* The air handling unit is supplied without end connection panel if a duct accessory housed in an insulated casing will be connected.

Division into sections for transport Clear space for inspectionA clear space of 900 mm should be provided in front of the unit and at least 200 mm should be provided above the junction hood.

Power connection3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A


98

GOLD








Max. airflow

m3/h m3/s m3/h m3/s14 720 0.20 5940 1.65

Range in dia-gram chart


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -11 -16 -14 -27 -33 -37 -38 -34

2 -6 -9 -14 -28 -35 -39 -43 -39


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48



program.

99

GOLD

GO

LD




Delivery and Transport within the SiteThe GOLD PX 14 is always supplied as one unit. The air handling unit can be split into three sections to facilitate transporting it within the building site.





B: Specify whether the unit shall have an air intake from above for outdoor air and/or extract air when placing orders (not for outdoor units).


Clear Space for InspectionA clear space of 900 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood.



Power connection


A AD + 19 mm

80

D

E E

M M

52 5050

52

N

If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accessories) can be used for this purpose.

Size A B C D E F G H I J K L M N Weight, kg

14 765 1400 1136 1300 450 400 1000 1395 298 188 200 2830 208 109 667-773


Right-hand version

Left-hand version


100

GOLD







Max. airflow

m3/h m3/s m3/h m3/s20 1080 0.30 7560 2.10


Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -11 -16 -14 -27 -33 -37 -38 -34

2 -6 -9 -14 -28 -35 -39 -43 -39


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48



program.

101

GOLD

GO

LD




Delivery and Transport within the SiteThe GOLD PX 20 is always supplied as one unit. The air handling unit can be split into three sections to facilitate transporting it within the building site.







A AD + 19 mm

Power connection

80

D

E E

M M

52 5050

52

N




20 765 1400 1136 1300 450 400 1000 1395 298 188 200 2830 208 109 703-809


Right-hand version

Left-hand version


Power connection3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A (capacity variant 1) alt. 16 A (capacity variant 2)


102

GOLD







Max. airflow

m3/h m3/s m3/h m3/s25 1080 0.30 9000 2.50


Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -11 -16 -14 -27 -33 -37 -38 -34

2 -6 -9 -14 -28 -35 -39 -43 -39


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48



program.

103

GOLD

GO

LD




Delivery and Transport within the SiteThe GOLD PX 25 is supplied as two units. The one unit con-sists of the centre section with heat exchanger and the fan/filter section to the right of the centre section (viewed from the inspection side). The other unit consists of a fan/filter section to the left of the centre section (viewed from the inspection side). The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electri-cal and control cables have quick connectors.The air handling unit is delivered on wooden beams.The electrical equipment cubicle and the drain pipe on the front of the air handling unit can be removed, if required, for trans-porting the unit within the building site.



Clear Space for InspectionA clear space of 900 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood.




A AD + 19 mm

Power connection

80

D

E E

M M

52 5050

52

N




25 835 1600 1336 1550 575 500 1200 1595 298 203 200 3220 193 94 905-1058


Right-hand version

Left-hand version


104

GOLD







Max. airflow

m3/h m3/s m3/h m3/s30 1800 0.50 11520 3.20


Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -11 -16 -14 -27 -33 -37 -38 -34

2 -6 -9 -14 -28 -35 -39 -43 -39


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48



program.

105

GOLD

GO

LD




Delivery and Transport within the SiteThe GOLD PX 30 is supplied as two units. The one unit con-sists of the centre section with heat exchanger and the fan/filter section to the right of the centre section (viewed from the inspection side). The other unit consists of a fan/filter section to the left of the centre section (viewed from the inspection side). The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electri-cal and control cables have quick connectors.The air handling unit is delivered on wooden beams.The electrical equipment cubicle and the drain pipe on the front of the air handling unit can be removed, if required, for trans-porting the unit within the building site.




A AD + 19 mm

Power connection

80

D

E E

M M

52 5050

52

N




30 835 1600 1336 1550 575 500 1200 1595 298 203 200 3220 193 94 945-1098


Right-hand version

Left-hand version




106

GOLD


GOLD CX, coil heat exchangers, size 35



* The integral attenuation of filters and coil heat exchangers has been taken into account. ** Total sound power level emitted to the surroundings is calcu-lated as the sum of the levels in the supply air and the extract air.



Max. airflow

m3/h m3/s m3/h m3/s35 2700 0.75 14040 3.90

Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48

Fan motor, 6.5 kW.

75dB 80 85Lw,tot

75dB 80 85Lw,tot

2.5

2.0

1.5

12

12

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h

The lower limit for the airflow when the unit is operating in the airflow regulation mode.


The diagram shows the air handling unit including the end connection panels.

107

GOLD

GO

LD


250

M

5250

50250

M

5050 52

N

N




35 948 1990 1726 680 200 600 1400 1985 392 153 295 2575 600 240 1355

Delivery and Transport within the SiteThe GOLD CX 35 is supplied as two units. The one unit consists of the centre section with heat exchanger and the fan/filter section where the fan is mounted in the upper level. The other unit consists of a fan/filter section in which the fan is placed in the lower level.

The air handling unit can be split into three sections to facilitate transporting it within the building site.



The coil heat exchanger system is filled with liquid from the factory.


B: The arrangement of the functional sections can be vertically reversed. Specify this by selecting fan arrangement 1 or 2 when placing orders!

C: Specify upper fan outlet for upward air discharge when ordering. (not for units installed outdoors).

Right-hand version

Left-hand version

Upward UpwardForwardForward

Fan arrangement 1 Fan arrangement 2


Upward Upward

ForwardForward


Clear Space for InspectionA clear space of 900 mm should be provided in front of the unit.


Rated data per fanMotor shaft power: 6.5 kW (3.9 kW)* motor control system, 3 x 400 V, 50 Hz *The motor control system limits the power of the take-off to the value

specified.

Power connection

The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 404 kg, D = 547 kg.A AD+19 mm

If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accesso-ries) can be used for this purpose. Applicable to the right-hand version, fan arrangement 2 and the left-hand version, fan arrangement 1:The dimension print shows the connection configuration for fan arrangement 1. For fan arrangement 2 the connections are mirror-inverted.



108

GOLD







Max. airflow

m3/h m3/s m3/h m3/s40 2700 0.75 18000 5.00


Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48

Fan motor, 6.5 kW.

2.5

2.0

1.5

12

12

75dB 80 85 90Lw,tot

75dB 80 85 90Lw,tot

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h




109

GOLD

GO

LD












Clear Space for InspectionA clear space of 900 mm should be provided in front of the unit.


Rated data per fanMotor shaft power: 6.5 kW, motor control system, 3 x 400 V, 50 Hz

The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 404 kg, D = 547 kg.


40 948 1990 1726 680 200 600 1400 1985 392 153 295 2575 600 240 1355

250

M

5250

50250

M

5050 52

N

N

Power connection

If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accesso-ries) can be used for this purpose. Applicable to the right-hand version, fan arrangement 2 and the left-hand version, fan arrangement 1:The dimension print shows the connection configuration for fan arrangement 1. For fan arrangement 2 the connections are mirror-inverted.


A AD+19 mm

Right-hand version

Left-hand version




Upward Upward

ForwardForward



110

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48


Max. airflow

m3/h m3/s m3/h m3/s50 3600 1.00 18000 5.00

Fan motor: 2 x 4.0 kW

75dB 80 85

90

Lw,tot

75dB 80 85

90

Lw,tot

2.5

2.0

1.5

12

12

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h




111

GOLD

GO

LD


28

28*

76254

M76



Size A B D E F G H I J K L M Weight, kg

50 1050 2318 760 150 800 1600 2253 423 115 360 2860 650 2045




The unit is supplied on 100 mm high support feet made of steel.





Upward Upward

ForwardForward

Upward Upward

ForwardForward

Right-hand version

Left-hand version




The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 542 kg, D = 961 kg.

Clear Space for InspectionA clear space of 1,100 mm should be provided in front of the unit.


Rated data per fanMotor shaft power: 2 x 4.0 kW (2 x 2.4 kW)* motor control system, 3 x 400 V, 50 Hz *The motor control system limits the power of the take-off to the value

specified.

Power connection

Supplied on 100 mm high support feet. They can be removed or kept as they are when the unit is in place. Applicable to the right-hand version, fan arrangement 2 and the left-hand version, fan arrangement 1: If a water trap is fitted, in addition to the base beams, the air handling unit must be raised at least 50 mm to provide space for the water trap. It is advisable to let these support feet remain on the unit. Or you can remove them and fit adjustable feet (accessory).

A AD

* The air handling unit

is supplied without end

connection panel if a

duct accessory housed in

an insulated casing will

be connected.


112

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48


Max. airflow

m3/h m3/s m3/h m3/s60 3600 1.00 23400 6.50

75dB 80 85 90Lw,tot

75dB 80 85 90Lw,tot

2.5

2.0

1.5

12

12

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h



Fan motor: 2 x 4.0 kW, capacity variant 1 Fan motor: 2 x 6.5 kW, capacity variant 2

75dB 80 85 90

95

Lw,tot

2.5

2.0

1.5

75dB 80 85 90

95

Lw,tot

12

12

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h


113

GOLD

GO

LD





60 1050 2318 760 150 800 1600 2253 423 115 360 2860 650 2045









The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 542 kg, D = 961 kg.A AD

28

28*

76254

M76

Power connection







be connected.

Upward Upward

ForwardForward

Upward Upward

ForwardForward

Right-hand version

Left-hand version




Division into sections for transport Clear space for inspectionA clear space of 1,100 mm should be provided in front of the unit.


Rated data per fanMotor shaft power: 2 x 4.0 kW alt. 2 x 6.5 kW, motor control system: 3 x 400 V, 50 Hz

114

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48


Max. airflow

m3/h m3/s m3/h m3/s70 5400 1.50 27000 7.50


75dB 80 85

90

Lw,tot

75dB 80 85

90

Lw,tot

2.5

2.0

1.5

12

12

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h




115

GOLD

GO

LD


254

M7676

52

52*

27


70 1275 2637 760 164 1000 1800 2640 319 161 419 3310 800 3030









The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 866 kg, D = 1,298 kg.



Rated data per fanMotor shaft power: 2 x 6.5 kW (2 x 3.9 kW)* motor control system, 3 x 400 V, 50 Hz *The motor control system limits the power of the take-off to the value

specified.

Power connection









be connected.

Upward Upward

ForwardForward

Upward Upward

ForwardForward

Right-hand version

Left-hand version





A AD

116

GOLD







Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48


Max. airflow

m3/h m3/s m3/h m3/s80 5400 1,50 34200 9,50

2.5

2.01.5

75dB 80 85 90Lw,tot

75dB 80 85 90Lw,tot

12

12

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h




Fan motor: 2 x 6.5 kW, capacity variant 1 Fan motor: 2 x 10 kW, capacity variant 2

2.5

2.01.5

12

12

75dB 80 85 90Lw,tot

75dB 80 85 90Lw,tot

95

95

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h

Supply air fan

Extract air fan

117

GOLD

GO

LD





80 1275 2637 760 164 1000 1800 2640 319 161 419 3310 800 3030









The unit can be divided into three sections at the building site.Dimensions: See A and D in the table above.Weight: A = 866 kg, D = 1,298 kg.



Rated data per fanMotor shaft power: 2 x 6.5 kW alt. 2 x 10 kW, motor control system: 3 x 400 V, 50 Hz

254

M7676

52

52*

27







be connected.

Upward Upward

ForwardForward

Upward Upward

ForwardForward

Right-hand version

Left-hand version





A AD

118

GOLD


2.5

2.0

1.5

12

12

80dB 85 90Lw,tot

80dB 85 90Lw,tot



Min. and max. AirflowsThe flows specified refer to those that can be preset in the hand-held micro terminal. The practical flow limits are deter-mined by the external pressure drop.


Max. airflow

m3/h m3/s m3/h m3/s100 9000 2.50 39 600 11.0



Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h

Recommended working range for sizing.Permissible operating range when the fan is controlled to operate at a lower speed. The lower limit for the airflow when the unit is operat-ing in the airflow regulation mode; see the black broken line in the diagram. If pressure regulation is used, the airflow can be regulated to zero, however this presupposes a certain static pressure drop in the ducting (approx. 50 Pa).




Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48

119

GOLD

GO

LD




Delivery and transport within the siteThe GOLD CX 100 is supplied as six separate sections: Two fan sections, two filter sections and two coil heat ex-changer sections. The six sections must be fitted together at the building site. The pipework package including the control box can be ordered as accessories and are sup-plied in unassembled condition for floor or wall mounting (see TBXZ pipework package under Accessories).

The three sections are to be jointed together by bolts and the electrical and control cables are simple to connect.


B: The arrangement of the functional sections can vary. To be specified when ordering as fan arrangement 1, 2, 4 or 5. For fan arrangement 4 and 5, you should also specify: supply air in upper or lower level.

C: Specify upper fan outlet for upward air discharge when placing orders (not for outdoor units). N.B.! Duct connec-tion size: 2500 x 800 mm.



Upward Upward

ForwardForward

Right-hand version



Filter and fan sections See dimensions A and P in the table above. Weight: fan section = 875 kg, filter section = 529 kg.

Heat exchanger sectionsSee dimensions D and P in the table above. Weight: Heat exchanger section = 880 kg.

Clear space for inspectionA clear space of 1,000 mm should be provided in front of the unit.Power connection3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 50 ARated data per fanMotor shaft power: 3 x 6.5 kW (3 x 3.9 kW)*, motor control system: 3 x 400 V, 50 Hz *The motor control system limits the output power to the value speci-fied.

Transport at building site, dim. and weights

Fan arrangement 5, supply air – upper level

Fan arrangement 5, supply air - lower level


Upward UpwardForward

Forward

Left-hand version




Size A B D E F G H I J K L M N O P Weight, kg

100 1126 3340 1070 191 1200 2400 3440 520 210 470 3322 800 170 2500 1720 4568

56*

56

M

P

P

N O N

137

77 3186 77

1048 1000 10481048122

45

Power connectionIf extract air flows through the lower level: The air handling unit must be raised at least 50 mm (higher than the upper edge of the base beams) to provide space for the water trap. This can be done by mounting adjust-able feet (accessories).

120

GOLD


2.5

2.01.5

12

12

80dB 85 90 95Lw,tot

80dB 85 90 95Lw,tot

12

12

80dB 85 90 95Lw,tot

80dB 85 90 95Lw,tot

2.5

2.01.5





Max. airflow

m3/h m3/s m3/h m3/s120 9000 2.50 50 400 14.0


Fan motor: 3 x 6.5 kW, capacity variant 1

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h

Recommended working range for sizing.Permissible operating range when the fan is controlled to operate at a lower speed. The lower limit for the airflow when the unit is operat-ing in the airflow regulation mode; see the black broken line in the diagram. If pressure regulation is used, the airflow can be regulated to zero, however this presupposes a certain static pressure drop in the ducting (approx. 50 Pa).



Fan motor: 3 x 10 kW, capacity variant 2

Supply air fan

Extract air fan

SFPv

Airflow, m3/s

Ava

ilab

le t

ota

l pre

ssu

re r

ise,

Pa

Airflow, m3/h


Range in the

diagram


Sound path 1 2 3 4 5 6 7 8

63 125 250 500 1000 2000 4000 8000

To outlet duct 1 -4 -9 -7 -5 -8 -9 -11 -11

2 2 -4 -7 -7 -10 -12 -16 -17

To inlet duct* 1 -10 -10 -8 -21 -28 -30 -35 -32

2 -5 -3 -8 -22 -30 -32 -40 -37


1 -15 -23 -30 -26 -41 -42 -45 -42

2 -9 -18 -30 -28 -43 -45 -50 -48

121

GOLD

GO

LD




Filter and fan sections See dimensions A and P in the table above. Weight: fan section = 875 kg, filter section = 529 kg.

Heat exchanger sectionsSee dimensions D and P in the table above. Weight: Heat exchanger section = 880 kg.

Clear space for inspectionA clear space of 1,000 mm should be provided in front of the unit.Power connection3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 80 A (capacity variant 1) alt. 125 A (capacity variant 2)Rated data per fanMotor shaft power: 3 x 6.5 kW alt 3 x 10 kW, motor control system: 3 x 400 V, 50 Hz

Transport at building site, dim. and weights

Delivery and transport within the siteThe GOLD CX 120 is supplied as six separate sections: Two fan sections, two filter sections and two coil heat ex-changer sections. The six sections must be fitted together at the building site. The pipework package including the control box can be ordered as accessories and are sup-plied in unassembled condition for floor or wall mounting (see TBXZ pipework package under Accessories).

The three sections are to be jointed together by bolts and the electrical and control cables are simple to connect.


B: The arrangement of the functional sections can vary. To be specified when ordering as fan arrangement 1, 2, 4 or 5. For fan arrangement 4 and 5, you should also specify: supply air in upper or lower level.

C: Specify upper fan outlet for upward air discharge when placing orders (not for outdoor units). N.B.! Duct connec-tion size: 2500 x 800 mm.


Upward Upward

ForwardForward

Right-hand version



Power connection




Upward UpwardForward

Forward

Left-hand version




Size A B D E F G H I J K L M N O P Weight, kg

120 1126 3340 1070 191 1200 2400 3440 520 210 470 3322 800 170 2500 1720 4568

56*

56

M

P

P

N O N

137

77 3186 77

1048 1000 10481048122

45


If extract air flows through the lower level: The air handling unit must be raised at least 50 mm (higher than the upper edge of the base beams) to provide space for the water trap. This can be done by mounting adjust-able feet (accessories).

The sizing diagram will be available later on! For sizing ... Archive/Air handling units/GOLD...

Documents

Transcript of The sizing diagram will be available later on! For sizing ... Archive/Air handling units/GOLD...