Technical instruction practice

Technical Wri,ng | Alex, Alice, Jiny Kansas State University | 2015-‐Summer

HOW TO MAKE A

Part Needed

Gear : 3 white, 2 yellow, 8 red S,ck : 1 green, 3 red, 8 yellow,

1 blue Wheel : 2 thick, 4 thin Block : 4 gray, 1 red, 2 black 6 gray cog wheel, A orange connector, 6 skyblue rings, 2 yellow clips, 2 point cogs

CARICOPTER Car�� +�� Helicopter��


Wheel Part Front wheel

-‐ Part Needed -‐ Result

Instruction

1. Put one blue s)ck into the center hole of the yellow gear.

2. Put 3 sky-‐blue rings on each side of s,ck.

3. Put one thin wheel and one point cog on each side of s,ck.



Instruction

4. Put one red s)ck into the center hole of the yellow gear.

5. Put one cog wheel on each side of s,ck. Longer part of the wheel should face on the outside.

6. Put one cog wheel whose longer part faces on inside. Repeat this on other side of s,ck.

Wheel Part Back wheel

Longer part


Instruction

7. Put one thin wheel on each side of s,ck.

Wheel Part Back wheel

8. Put one thick wheel on each side of s,ck. Press hard to fix them.



Instruction

9. Put one yellow s)ck on the square hole in center of the red gear.

Propeller Part

Tip #9. Don’t push like -‐> direc,on. Just press s,ck from up to below. <Side View>

Gear S,ck


10. Repeat <instruc,on 9> eight ,mes.

11. Put the result of <instruc,on 10> on the white gear.

Propeller Part

12. Repeat <instruc,on 11>.

Instruction(Cont’d)

13. Repeat un,l there is no empty part on gear.



14. Put one red s)ck into a cog wheel as much as 1/3. The longer part of the wheel should face on the longer part of s,ck.

15. Put the result of <instruc,on 14> into the white gear’s hole of the result of <instruc,on 13>. It has to come in touch with shorter part of the cog wheel.

Propeller Part

16. Put a cog wheel into the other side of s,ck. The longer part of the wheel should face above. S,ck all of the part.



Instruction

17. Put one clip’s round side on the white gear. Repeat twice.

18. Put the result of <instruc,on 17> into the center hole of gray block. Block’s longer side and gear should be parallelized.

Body Part

19. Put one red s)ck to yellow gear’s hole in end of <Instruc,on 8> and close the broaden gap. There is a ,p on next page.


21. Put two gray blocks on the <instruc,on 20>’s blocks. Blocks should put half of each.


Body Part

Tip #19. It will be easy if you broaden the gap of the cog wheels. Don’t push like <-‐ direc,on. Just press s,ck from front to behind. <High View>

Gear S,ck

20. Put the result of <instruc,on 19>’s s,ck to results of <instruc,on 18>’s center hole. S,ck together to gray blocks.


22. Fix one red block between two gray blocks that fixed in above.

23. Make the back of chair with two black blocks.


Body Part

Behind view of <instruc,on 23>

24. Connect yellow gear’s hole in end of the Front wheel with result of <instruc,on 23>. Tip #24 Reference Tip #19.



Instruction

25. Put an orange connector on a green s)ck.

26. Put the result of <instruc,on 25> to the center hole of wheel’s gear.

Connect Part


28. Put the s,ck of propeller part on the center hole of back wheel’s gear.

27. Connect the propeller part with connector.


Connect Part

Tip #28. It will be easy if you broaden the gap of the cog wheels.


COMPLETE J

Result

Technical instruction practice

Education

Transcript of Technical instruction practice