SW1008WEB Managed Switch Manual -
Transcript of SW1008WEB Managed Switch Manual -
1
SW1008WEB Managed Switch
Manual
Catalog
一、WEB Page review
1、WEB access characteristics ................................................................................ 2
2、System Requirements for Web Browsing ........................................................ 2
3、Login of WEB Browsing Session......................................................................... 3
4、Basic Composition of WEB Pages ...................................................................... 4
5、Navigation Tree Structure .................................................................................... 4
6、Introduction of Page Button ............................................................................... 5
7、Error message ......................................................................................................... 5
二、WEB Page review .......................................................................................................... 2
1、Login Dialog ............................................................................................................ 6
2、Main page ................................................................................................................ 6
3、System ....................................................................................................................... 7
4、To Configure .............................................................................................................. 9
5、Safty ......................................................................................................................... 15
6、Testing ..................................................................................................................... 17
7、Tool .......................................................................................................................... 17
2
WEB page manual
This manual mainly describes the WEB pages of the switch. Users can manage the switch
through the WEB pages of the switch. This manual only gives a brief introduction to the
operation of each WEB page. This manual mainly includes the following contents:
1. WEB Page Overview
2. WEB Page Introduction
一、WEB Page review
1、WEB access characteristics
Switches provide Web access for users. Users can access the switch through Web
browser to manage and configure the switch. The main features of WEB visits are:
Easy access: Users can easily access switches from anywhere in the network.
Users can use familiar browsers such as Netscape Communicator and Microsoft
Internet Explorer to access the WEB pages of switches. The WEB pages are
presented graphically and tabularly to users.
Switches provide rich WEB pages through which users can configure and manage the
functions of switches.
WEB page functions are classified and integrated to facilitate users to find relevant
pages for configuration and management.
2、The system requirements for Web browsing are shown in Table 1.
Hardware and
Software
System Requirement
CPU Pentium 586 above
RAM 128MB above
Resolution 800x600 above
Color 256 colors above
Browser IE4.0 above or Netscape4.01 above
Operating
System
Microsoft® ,Windows95®,Windows98®,WindowsNT®,
Windows2000®,WindowsXP®,WindowsME®, Windows Vista®,
Windows7®, Windows8®,MAC, Linux, Unix operating system
3
Note:
Microsoft®,Windows95®,Windows98®,WindowsNT®,Windows2000®,WindowsXP
®,Windows ME®, Windows Vista ®, Windows7®, Windows8® are registered trademarks of
Microsoft Corporation, all other product names, trademarks, registered trademarks and service
marks, Copyright is held by their respective owners.
3、3、WEB browsing session login
Users need to confirm before starting a Web browsing session:
The switch has been IP-configured. By default, the VLAN1 interface IP address of the
switch is 192.168.1.199.
Subnet mask is 255.255.255.0
A host installed with a Web browser has been connected to the network, and the host
can PING through the switch.
After completing the above two tasks, users enter the address of the switch in the
browser's address bar and press Enter to enter the switch Web login page, as shown in Figure
1. When users log on to the Web, their account passwords are admin.
If the system has enabled the setting of new users and passwords, entering the
default empty account password will not take effect and users will not access the Web
successfully.
Figure 1 The login page of the WEB browsing session
4
4、WEB Basic Composition of Pages
As shown in Figure 2, WEB pages are mainly composed of three parts: Title pages, navigation
tree pages and home pages.
Figure 2 Basic Composition Page of Switch WEB Page
Title Page: The port status for real-time display is shown in the following figure
The green light indicates that the port is connected.
The gray light indicates that the port is not connected.
Main page Used to display pages selected by users from the navigation tree。
5、Navigation Tree Structure
Figure 3 shows the organizational structure of the navigation tree.
Navigation tree is located at the bottom left of each page. The node of WEB page is
displayed in the way of tree. Users can easily find the WEB page to be managed. According to
the different functions of web pages, they are divided into different groups, each group
includes one or more pages. In most navigation trees, the page name is the abbreviation of the
page title at the top of the corresponding page.。
5
Figure 3 The organizational structure page of the switch navigation tree
6、Introduction of Page Button
In general some of the buttons on the page, the role of these buttons are generally the same,
are presented in Table 2 for the button function.
Table2:
Button Effect
Application Put the updated values in memory.
Add/Modify Create new or delete options。
Choose all Select all items or lists
Delete Delete all the information
7、Error messenger
If an error occurs in the WEB server of the switch when processing user requests, the
corresponding error information will be displayed in a dialog box. For example, Figure 4
shows an error message dialog box。
Figure 4 Error Information Page
6
二、WEB page introduce
The WEB pages of switches are organized into groups, each group includes one or
more WEB pages. The following pages are introduced one by one
1、Login Dialog
Figure 5 The login page of the WEB browsing session
Figure 5 shows the login dialog box, which is displayed when the user first logs on to the
Web page. The user enters the user name and password in the corresponding field, and then
clicks the confirmation key to log in to the Web server of the switch. Passwords are
case-sensitive. Anonymous usernames can be set up to 16 characters, while passwords can
be set up to 8 characters.。
The default user and password for the first logon switch are admin by default
2、Main page
Figure 6 shows the WEB home page of the switch. This page will be displayed after the
user logs in to the page
Figure 6 Switch Home Page
7
3、System
(1)、System messenge
Figure 7 is the basic information page of the system.
Equipment Model Display Switch Model
The MAC address shows the physical MAC address of the switch.
IP address IP address display switch management.
Subnet Mask Display Subnet Mask of IP Address Managed by Switch
Gateway Display Switch Manages IP Address Gateway
The firmware version shows the firmware version of the switch.
Firmware date shows switch firmware version date.
Hardware Version Displays Handover Hardware Version。
Figure 7 Basic System Information
(2)IP Setting
Figure 8 IP Setup Page, which sets the switch management IP。
DHCP settings are disabled and opened. Setting disabled requires manual setting of
management IP address, subnet mask, default gateway. Setting up the open system will
automatically get the handover management IP address (no special case is not
recommended to open)。
IP Address Sets the Address of Switch Management
Subnet Mask Settings for Switch Management Subnet Masks
Default Gateway Settings for Switch Gateway Address
Figure 8 IP Setup Page
8
(3)User setting
Figure9 User Settings Page which sets user names and passwords forlogin Web Management。
The new username manages user settings for switches, up to 16 characters.
The new password sets the switch management user password, which can be set up to 8
characters.
Enter the password again to confirm the new password settings of the switch management
user
Click the Application button to set up successfully
Figure 9 user setting
(4)Port setting
Figure 10 Port Setup Page, through which the port number selected in the port can control the
switch port status (open or prohibit), speed (automatic, single or double-tap), traffic, and
display the status of each port through a list。
Figure 10 Port Setup Page
9
4、To configure
(1)VLAN
1)VLAN Configuration
Figure 11: The VLAN setup page, which creates the VLAN and divides the port into its
own VLAN.
If a new VLAN is created and entered into the VID in the VLAN number bar, the numerical
range is 1-4094, and the VLAN name is to define a name for the VID. The name can not
exceed 16 characters at most (the VLAN name can also be empty). After clicking the
Add/Modify button, it is added successfully.
To divide the ports of VLAN, first input the VLAN number and VLAN name, then click on
the circle corresponding to the port number after no TAG tag or TAG tag bar. Finally, click the
Add/Modify button to set up successfully.
A port may not be a member of a VLAN, but may be a TAG tagged member of a VLAN or
no TAG member. The character meaning before the port of the page is as follows:
TAG The port is the TAG tag member of the VLAN (TAG can be in multiple VLANs)
NO TAG The port is a TAG-free member of the VLAN (no TAG belongs to only one VLAN)
Figure11 VLAN Configuration
2)VLAN Port setting
Figure 12. The VLAN port setup page, which sets the PVID of the port. On the page, the
corresponding port number is selected through the port, the corresponding VLAN is input by
the PVID, and then the allowable types are selected: all, tag-only, untag-only. Click the
Application button to set up successfully. And you can view all port settings through the list
information.
10
Tag-only: Allows passage with TAG Tags
Untag-only: Allows no TAG tag to pass
All: TAG tags and no TAG tags are allowed to pass (default settings all)
Figure 12 VLAN port setting
3)Priority selection
Figure 13 Port Priority Page, which prioritizes the transmission speed of switch ports. The
higher the value, the higher the priority。
Figure 13 Port Priority Page
4)Queue weight
Figure 14 Queue Weight Page, which defines the weight value by selecting the
corresponding priority in the queue priority. (The minimum weight is 1 and the maximum
weight is 15)。
11
Figure14 queue weight
(5)Loop detection
Figure 15 Loop Detection Page. This page is about setting up the protection function of the
ring network. Realizing the Redundancy Function of the Loop Network by Selecting "Loop
Detection"
Figure15 loop detection
(6)Port Mirror
Figure 16 Port Mirror Page, which sets the port image. Setting by choosing different
parameters of mirror settings, mirror ports and mirrored ports。
Mirror Indicator: RX listens for incoming packets. TX listens for sent packets. BOTH listens for
all data packets received and sent。
12
Figure 16 port mirror
(7)Port isoltation
Figure 17 Port Isolation Page, which is the port isolation settings. By choosing the port
number and forwarding port, the control port is directly isolated from the port or communicates
with the port. If you need to select multiple ports at the same time, hold down Ctrl and click on
port number.
Port Isolation List: 1-8 indicates that the port is not isolated and can communicate with any
port. (If port 1 does not isolate the upstream port, other port isolation can be set with reference
to Fig. 17)。
Figure17 port isolation
(8)Bandwidth control
Figure 18 Bandwidth Control Page, which is used to configure the rate of port sending and
receiving. The bandwidth speed of the port is controlled by selecting the port, type, state and
rate.
Type: Receiving means receiving data packets, i.e. downlink bandwidth.
Sending means sending data packets, i.e. upstream bandwidth.
Rate (Kbit/s): Bandwidth is set in the range of 0-1000000 and is an integral multiple of 8.。
13
Figur18 bandwidth control
(9))Jumbo frame
Figure 19 Giant Frame Page, which sets the Giant Frame Packet settings. The lowest
value is 1522, and the highest value is 16383。
Figure19 Jumo frame page
(10)MAC limited
Figure 20 MAC Restriction Page, which restricts the learning of MAC addresses. In the pages
of MAC learning bar selection discarded or red MAC set limit setting, click the Apply button
settings to take effect. Select the port number corresponding to the MAC restriction settings
port, state selection forbids or opens, enter the restriction bar to enter the value (range 0-4160),
click the application button to set the validity, and view the access restriction information
through the port list information.。
14
Figure20 MAC limited page
(11)Green ethernet
Figure 21 Green Ethernet, which is used to disable or turn on functionality. Automatically
converting ports into low-power states without interrupting network connections to reduce
network energy consumption。
Figure 21 Green Ethernet
(12)EEE
Figure 22 EEE page, which is used to disable or turn on EEE functions. EEE means
efficient ethernet. Automatically converts the port into a low power state without interrupting
the network connection, thus reducing the network energy consumption。
15
Figure22 EEE
5、Safety
(1)MAC address
1)MAC query
Figure 23 MAC Query Page, which searches for MAC address and VLAN number to find
the appropriate switch port to use。
Figure23 MAC query
2)Static state MAC
Figure 24: Static MAC settings page, which is used to bind or filter ports and MAC
addresses
On the page, the MAC address bar enters the MAC address, and the VLAN number
enters the VLAN and the port number of the binding. If it is released, it will not be ticked in the
source MAC blocking bar, if it is in the filter source MAC blocking bar。
16
Figure24 static state MAC setting
(2)Storm control
Figure 25 Storm Control Page, which configures broadcast, multicast, unknown unicast
and unknown multicast control functions for ports. Select the required parameters in storm
type, port, state and rate. The control rate term is used to configure the control rate of the port,
ranging from 8 to 1000000 in kbits. At the same time, you can view the configuration of
broadcast storm control on all ports through this page。
Figure25 storm control
17
6、Testing
(1)Port Statistics
Figure26 Port Statistics Page, through which you can view statistics of port sending and
receiving packages. Click Zero to recalculate all port packet data。
Figure26 port statistics
(2)Cable diagnosis
Figure27 Cable Diagnosis Page, with which you can select the port for click detection to
test the cable condition。
Figure27 cable disgnosis
7、Tool
(1)Firmware update
Figure 28 Firmware Update Page, click on the page to enter the download mode to
18
automatically download the latest version of the software. Finally, restart the switch。
Figure28 firmware update
(2)User Configuration and Recovery
Figure29 User Configuration and Recovery Page, which is a backup switch configuration
or the last backup configuration file recovery configuration. Click the Backup button on the
page to automatically backup and download the configuration information exchanged. To
restore the configuration, first click the Select File button, find the configuration file saved on
the computer, and then click Restore. Successful reconfiguration after restarting the switch。
Figure29 User Configuration and Recovery
(3)Restore factory settings
Figure 30 Restores the factory settings page. After clicking on the factory settings page, the
system automatically restarts and the system automatically restores to the default factory
settings。
Figure 30 Restore factory settings
(4)Saved
Figure 31 Save the page, click the Save button to automatically save the new
configuration information。
19
Figure31 saved page
(5)Reboot
Figure 32 Restart the page, click the Restart button on the page to restart the switch。
Figure32 reboot