Supplement to ISO Focus+ · PDF filefrom 1 to 29 February 2012 Committee Drafts ... Supplement...
Transcript of Supplement to ISO Focus+ · PDF filefrom 1 to 29 February 2012 Committee Drafts ... Supplement...
ISO Update
Supplement to ISO Focus+
March 2012
People and places
ISO Members 2
International Standards in processfrom 1 to 29 February 2012
Committee Drafts (CD) registered 3
Draft International Standards (DIS) circulated 5
Final draft International Standards (FDIS) circulated 8
Standards published 11
Standards confirmed 14
Standards withdrawn 14
Meeting calendar 15
People and places
2 ISO Update, Supplement to ISO Focus+– March 2012
ISO Members
Since the February 2012 issue of ISO Update Supplement to ISO Focus+, the following changes affecting ISO members have occurred:
Membership changes
Correspondent members
The membership status of the Eritrean Standards Institution (ESI) has been upgraded from subscriber member to correspondent member with retroactive effect as from 1 January 2012. Their contact details read as follows:
ERITREA (ESI)
Eritrean Standards Institution ASMARA
Postal address:
171-1 House No. 9 P.O. Box 245 ASMARA
General Manager: Mr. Beyene Mesghenna
Tel. +291 1 12 20 05 Fax +291 1 12 02 45 E-mail [email protected]
The standards body for Niger has been re-admitted, as a correspondent member, with retroactive effect as of 1 January 2012. Their contact details read as follows:
NIGER (DNPQM)
Direction de la Normalisation, de la Promotion de la Qualité et de la Métrologie 3ème étage Immeuble ex-BDRN BP : 11700 NIAMEY
Directeur: M. Issa Boubacar
Tel. +227 20 73 69 50 Fax +227 20 73 27 59 E-mail [email protected]
New CEOs :
Member bodies
EGYPT (EOS)
Acting Chairman: Dr. Hassan Abd El-Magied
JORDAN (JSMO)
Director General: Dr. Haydar Al-Zeben
PANAMA (COPANIT)
Chief Executive Officer: (Vacant)
Address change
Member bodies
GHANA (GSA)
Ghana Standards Authority Near Tetteh Quarshie Interchange ACCRA
Postal address:
P.O.BOX MB 245 ACCRA
Tel. +233 30 25 00 65 Fax +233 30 25 00 092 E-mail [email protected] Web www.gsa.gov.gh
SINGAPORE (SPRING SG)
E-mail [email protected]
ISO Update, Supplement to ISO Focus -- March 2012 3
International Standards in process
An International Standard is the result of an agreement between the member bodies of ISO. A first important step towards an International Standard takes the form of a committee draft (CD) - this is circulated for study within an ISO technical committee. When consensus has been reached within the technical committee, the document is sent to the Central Secretariat for processing as a draft International Stand-ard (DIS). The DIS requires approval by at least 75 % of the member bodies casting a vote. A confirmation vote is subsequently carried out on a final draft International Standard (FDIS), the approval criteria remaining the same.
CD registered
Period from 01 February to 29 February 2012
These documents are currently under consideration in the technical committee.
They have been registred at the Central Secretariat.
TC 6 Paper, board and pulps
ISO/CD 14778 Paper and board — Determination of contact angle
TC 8 Ships and marine technology
ISO/CD 14886 Ships and marine technology - Large Yachts - Structural fire protection for FRP yachts
ISO/CD 16556 Large Yachts — Deck equipment — Anchoring equipments
TC 17 Steel
ISO/CD 13933 Steel and iron — Determination of calcium and magnesium — Inductively coupled plasma atomic emisson spectrometric method
ISO/CD 19272 Alloyed steel — Determination of fifteen ele-ments — Glow discharge optical emission spectrometry
ISO/CD 683-17 Heat-treated steels, alloy steels and free-cutting steels — Part 17: Ball and roller bearing steels
TC 20 Aircraft and space vehicles
ISO/CD 16290 Definition of the Technology Readiness Levels (TRL) and their criteria of assessment
TC 22 Road vehicles
ISO/DTR 12353-3
Road vehicles — Traffic accident analysis — Part 3: Guidelines for the interpretation of recorded crash pulse data to determine impact severity
ISO/CD 12617 Liquefied natural gas vehicles — Connector for reflueling vehicles
TC 28 Petroleum products and lubricants
ISO/CD 8311 Refrigerated light hydrocarbon fluids — Cali-bration of membrane tanks and independ-ent prismatic tanks in ships — Physical measurement
TC 29 Small tools
ISO/CD 1711-1 Assembly tools for screws and nuts — Techni-cal specifications — Part 1: Hand-operated wrenches and sockets
ISO/CD 1711-2 Assembly tools for screws and nuts — Techni-cal specifications — Part 2: Machine-operated sockets ("impact")
TC 34 Food products
ISO/CD 3657 Animal and vegetable fats and oils — Determi-nation of saponification value
ISO/DTS 21569-2
Foodstuffs — Methods of analysis for the detection of genetically modified organisms and derived products — Qualitative nucleic acid based methods — Part 2: Construct-specific real-time PCR method for detection of a genetic modification in linseed and linseed products
TC 35 Paints and varnishes
ISO/CD 16926 Paints and varnishes — Natural weathering of coatings — Determination of corrosion protec-tion performance
TC 43 Acoustics
ISO/CD 12913-1
Acoustics — Soundscape — Part 1: Definition and conceptual framework
TC 44 Welding and allied processes
ISO/CD 9453 Soft solder alloys — Chemical compositions and forms
TC 45 Rubber and rubber products
ISO/CD 1629 Rubber and latices — Nomenclature
ISO/DTR 16098
Reclaimed rubbers and reclaimed crumb rubbers — Evaluation of dispersion in rubber mixes
ISO/CD 5999 Flexible cellular polymeric materials — Polyu-rethane foam for load-bearing applications excluding carpet underlay — Specification
TC 46 Information and documentation
ISO/DTR 18128
Information and documentation — Risk identifi-cation and assessment for records systems
TC 94 Personal safety -- Protective clothing and equipment
ISO/CD 11613-4
Protective clothing for firefighters — Laboratory test methods and performance requirements — Part 4: Gloves
ISO/DTS 16975-2
Respiratory protective devices — Part 2: Guid-ance for selection, use and maintenance
TC 96 Cranes
ISO/CD 17096 Cranes — Safety — Load lifting attachments
TC 121 Anaesthetic and respiratory equipment
ISO/CD 8836 Suction catheters for use in the respiratory tract
ISO/CD 17256 Anaesthetic and respiratory equipment — Res-piratory therapy tubing and connectors
TC 126 Tobacco and tobacco products
ISO/CD 3550-3 Cigarettes — Determination of loss of tobacco from the ends — Part 3: Method using a vibro-bench
TC 131 Fluid power systems
ISO/CD 11943 Hydraulic fluid power — On-line automatic particle-counting systems for liquids — Meth-ods of calibration and validation
ISO/DTR 16386
Impact of changes in ISO fluid power particle counting — Contamination control and filter test standards
4 ISO Update, Supplement to ISO Focus -- March 2012
ISO/CD 18413 Hydraulic fluid power — Cleanliness of parts and components — Inspection document and principles related to contaminant collection, analysis and data reporting
TC 146 Air quality
ISO/CD 16000-27
Indoor air — Part 27: Determination of settled fibrous dust on surfaces by SEM (scanning electron microscopy) (direct method)
TC 147 Water quality
ISO/CD 16780 Water Quality — Determination of polychlorin-ated naphthalenes (PCN) — Method using gas chromatography (GC) and mass spectrometry (MS)
ISO/CD 13165-2
Water quality — Radium 226 — Part 2: Test method using emanometry
ISO/CD 5667-6 Water quality — Sampling — Part 6: Guidance on sampling of rivers and streams
ISO/CD 5667-14
Water quality — Sampling — Part 14: Guidance on quality assurance of environmental water sampling and handling
TC 149 Cycles
ISO/CD 4210-1 Cycles — Safety requirements for bicycles — Part 1: Terms and definitions
ISO/CD 4210-2 Cycles — Safety requirements for bicycles — Part 2: Requirements for city and trekking, young adult, mountain and racing bicycles
ISO/CD 4210-3 Cycles — Safety requirements for bicycles — Part 3: Common test methods
ISO/CD 4210-4 Cycles — Safety requirements for bicycles — Part 4: Braking test methods
ISO/CD 4210-5 Cycles — Safety requirements for bicycles — Part 5: Steering test methods
ISO/CD 4210-6 Cycles — Safety requirements for bicycles — Part 6: Frame and fork test methods
ISO/CD 4210-7 Cycles — Safety requirements for bicycles — Part 7: Wheels and rims test methods
ISO/CD 4210-8 Cycles — Safety requirements for bicycles — Part 8: Pedals and crank test methods
ISO/CD 4210-9 Cycles — Safety requirements for bicycles — Part 9: Saddles and seat-post test methods
ISO/CD 6742-3 Cycles — Lighting and retro-reflective devices — Part 3: Installation and use of devices
ISO/CD 6742-4 Cycles — Lighting and retro-reflective devices — Part 4: Lighting powered by cycle movement
ISO/CD 6742-5 Cycles — Lighting and retro-reflective devices — Part 5: Lighting not powered by cycle movement
TC 150 Implants for surgery
ISO/CD 16376 Implants for surgery — Evaluation method of endurance performance of metallic artificial hip stem using numerical simulation with finite element analysis
TC 156 Corrosion of metals and alloys
ISO/CD 17093 Corrosion of Metals and Alloys — Guidelines for corrosion test by electrochemical noise measurements
TC 161 Control and protective devices for gas and/or oil burners and appliances
ISO/CD 23551-5
Safety and control devices for gas burners and gas-burning appliances — Particular require-ments — Part 5: Manual gas valves
TC 165 Timber structures
ISO/CD 12122-1
Timber structures — Determination of Charac-teristic values — Part 1: Basic requirements
ISO/CD 12122-2
Timber structures — Determination of Char-acteristic values — Part 2: Requirements for Sawn timber
TC 173 Assistive products for persons with disability
ISO 7176-19:2008/CD Amd 1
Wheelchairs — Part 19: Wheeled mobility devices for use as seats in motor vehicles — Amendment 1: .
TC 178 Lifts, escalators and moving walks
ISO/DTS 22201-3
Lifts (elevators), escalators and moving walks — Programmable electronic systems in safety related applications — Part 3: Maintenance repair and retrofit activities (PESSRAL & PESSRAE)
TC 181 Safety of toys
ISO 8124-1:2009/CD Amd 4
Safety of toys — Part 1: Safety aspects related to mechanical and physical proper-ties — Amendment 4: Projectiles, rotors and propellers
TC 188 Small craft
ISO/CD 16315 Small craft — Electric propulsion systems
TC 193 Natural gas
ISO/DTR 16922
Natural gas — Odorization
ISO/CD 16960 Natural gas — Determination of sulfur com-pounds — Determination of total sulfur by oxidative microcoulometry method
TC 204 Intelligent transport systems
ISO/DTS 18234-8
Intelligent transport systems — Traffic and travel information via transport protocol experts group, generation 1 (TPEG1) binary data format — Part 8: Congestion and travel-time applica-tion (TPEG1-CTT)
TC 207 Environmental management
ISO/CD 14046 Life cycle assessment — Water footprint — Requirements and guidelines
TC 223 Societal security
ISO/CD 22397 Societal security — Public Private Partnership — Guidelines to set up partnership agreements
TC 229 Nanotechnologies
ISO/DTS 14101
Surface characterization of gold nanoparticles for nanomaterial specific toxicity screening: FT-IR method
ISO/DTS 16195
Nanotechnologies - Generic requirements for reference materials for development of meth-ods for characteristic testing, performance testing and safety testing of nanoparticle and nanofibre powders
ISO/DTS 17200
Nanotechnology — Nanoparticles in powder form — Characteristics and measurements
JTC 1 Information technology
ISO/IEC PDTR 20000-5
Information technology — Service manage-ment — Part 5: Exemplar implementation plan for ISO/IEC 20000-1
ISO/IEC PDTR 20000-10
Information technology — Service manage-ment — Part 10: Concepts and terminology
ISO/IEC PDTR 30103
Title missing
ISO/IEC PDTR 30126
Software engineering — Lifecycle profiles for Very Small Entities (VSEs)
ISO/IEC CD 90006
Information Technology — Guidelines for the application of ISO 9001:2000 to IT service management.
ISO 9660:1988/PDAM 1
Information processing — Volume and file structure of CD-ROM for information inter-change — Amendment 1
ISO Update, Supplement to ISO Focus -- March 2012 5
ISO/IEC 19775-2:2004/PDAM 1
Information technology — Computer graph-ics and image processing — Extensible 3D (X3D) — Part 2: Scene Access Interface (SAI) — Amendment 1
ISO/IEC CD 27033-5
Information technology — Security tech-niques — Network security — Part 5: Securing communications across networks using Virtual Private Network (VPNs)
ISO/IEC CD 11160-2
Information technology — Office equipment — Minimum information to be included in specification sheets — Printers — Part 2: Class 3 and Class 4 printers
ISO/IEC CD 11179-5
Information technology — Metadata registries (MDR) — Part 5: Naming and identification principles
ISO/IEC CD 19763-10
Information technology — Metamodel frame-work for interoperability (MFI) — Part 10: MFI Core model and basic mapping
ISO/IEC CD 19763-12
Information technology — Metamodel frame-work for interoperability (MFI) — Part 12: Metamodel for information model registration
ISO/IEC 19794-5:2011/PDAM 1
Information technology — Biometric data interchange formats — Part 5: Face image data — Amendment 1: Conformance testing methodology
ISO/IEC 19794-8:2011/PDAM 1
Information technology — Biometric data interchange formats — Part 8: Finger pattern skeletal data — Amendment 1: Conformance testing methodology
ISO/IEC PDTR 29198
Boimetrics - Characterization and measure-ment of difficulty for fingerprint databases for tehcnology evaluation
ISO/IEC CD 29794-6
Biometric Sample Quality Standard — Part 6: Iris Image
ISO/IEC CD 30106-3
Information Technology — Object orientated BioAPI — Part 3: Orientation
ISO/IEC CD 30108
Biometric identity assurance service (BIAS)
DIS circulated
Period from 01 February to 29 February 2012
These documents have obtained substantial support within the ap-propriate ISO technical committee.
They have been submitted to the ISO member bodies for voting by the date shown.
* Available in English only
Vote terminates
TC 2 Fasteners
ISO/DIS 14581 * Fasteners — Hexalobular socket countersunk flat head screws 2012-07-03
ISO/DIS 14582 * Hexalobular socket countersunk head screws, high head 2012-07-03
ISO/DIS 1891-2
* Fasteners — Terminology — Part 2: Vocabulary and definitions for coatings
2012-08-10
TC 6 Paper, board and pulps
ISO/DIS 8791-2
* Paper and board — Determina-tion of roughness/smoothness (air leak methods) — Part 2: Bendtsen method
2012-07-04
(Revision of ISO 8791-2:1990)
TC 8 Ships and marine technology
ISO/DIS 13073-2
* Ships and marine technology — Risk assessment on anti-fouling systems on ships — Part 2: Marine environmental risk as-sessment method for anti-fouling systems on ships using biocid-ally active substances
2012-07-25
TC 17 Steel
ISO/DIS 7452.2
* Hot-rolled steel plates — Toler-ances on dimensions and shape 2012-04-08
(Revision of ISO 7452:2002)
ISO/DIS 16160 * Hot-rolled steel sheet prod-ucts — Dimensional and shape tolerances
2012-07-08
(Revision of ISO 16160:2011)
ISO/DIS 404 Steel and steel products — General technical delivery requirements
2012-07-15
(Revision of ISO 404:1992)
ISO/DIS 10474 Metallic products — Inspection documents 2012-07-15
(Revision of ISO 10474:1991)
TC 20 Aircraft and space vehicles
ISO/DIS 11233 Space Systems — Orbit determi-nation and estimation — Process for describing techniques
2012-07-28
TC 21 Equipment for fire protec-tion and fire fighting
ISO/DIS 7240-14
* Fire detection and alarm systems — Part 14: Design, installation, commissioning and service of fire detection and fire alarm sys-tems in and around buildings
2012-07-04
(Revision of ISO/TR 7240-14:2003)
TC 22 Road vehicles
ISO/DIS 6623 * Internal combustion engines — Piston rings — Scraper rings made of cast iron
2012-07-16
(Revision of ISO 6623:2004)
ISO/DIS 6626-2
* Internal combustion engines — Piston rings — Part 2: Coil-spring-loaded oil control rings of narrow width made of cast iron
2012-07-22
(Revision of ISO 6626-2:2003)
ISO/DIS 8820-2
Road vehicles — Fuse-links — Part 2: User's guide 2012-07-28
(Revision of ISO 8820-2:2005)
ISO/DIS 11992-4
* Road vehicles — Interchange of digital information on electrical connections between towing and towed vehicles — Part 4: Diagnostic communication
2012-07-22
(Revision of ISO 11992-4:2005, ISO 11992-4:2005/Cor 1:2006)
ISO/DIS 18541-1.2
* Road vehicles — Standardized access to automotive repair and maintenance information (RMI) — Part 1: General information and use case definition
2012-04-13
6 ISO Update, Supplement to ISO Focus -- March 2012
ISO/DIS 22241-5.2
* Diesel engines — NOx reduction agent AUS 32 — Part 5: Refilling interface for passenger cars
2012-04-16
ISO/DIS 13044-2
Road vehicles — Fully automatic coupling systems 24 V (FACS) for heavy commercial vehicle combinations — Part 2: 50 mm fifth wheel couplings — Electrical and pneumatic interface
2012-07-29
TC 23 Tractors and machinery for agriculture and forestry
ISO/DIS 13693-1
Irrigation equipment — Safety devices for chemigation — Part 1: Small plastics valves for chemigation
2012-07-24
TC 24 Particle characterization including sieving
ISO/DIS 26824 * Particle characterization of par-ticulate systems — Vocabulary 2012-07-07
TC 29 Small toolsISO/DIS 1832 * Indexable inserts for cutting
tools — Designation 2012-07-03
(Revision of ISO 1832:2004)
ISO/DIS 5609-1
* Tool holders for internal turning with cylindrical shank for index-able inserts — Part 1: Designa-tion, styles, dimensions and calculation for corrections
2012-07-03
(Revision of ISO 5609:1998, ISO 6261:2011)
ISO/DIS 5609-2
* Tool holders for internal turning with cylindrical shank for index-able inserts — Part 2: Style F
2012-07-03
(Revision of ISO 5609:1998)
ISO/DIS 5609-3
* Tool holders for internal turning with cylindrical shank for index-able inserts — Part 3: Style K
2012-07-03
(Revision of ISO 5609:1998)
ISO/DIS 5609-4
* Tool holders for internal turning with cylindrical shank for index-able inserts — Part 4: Style L
2012-07-03
(Revision of ISO 5609:1998)
ISO/DIS 5609-5
* Tool holders for internal turning with cylindrical shank for index-able inserts — Part 5: Style U
2012-07-03
(Revision of ISO 5609:1998)
ISO/DIS 5609-6
* Tool holders for internal turning with cylindrical shank for index-able inserts — Part 6: Style Q
2012-07-03
(Revision of ISO 5609:1998)
TC 34 Food productsISO/DIS 4833-1
* Microbiology of food and animal feed — Horizontal method for the enumeration of microorgan-isms — Part 1: Colony count at 30 degrees C by the pour plate technique
2012-07-24
(Revision of ISO 4833:2003)
ISO/DIS 4833-2
* Microbiology of food and animal feed — Horizontal method for the enumeration of microorgan-isms — Part 2: Colony count at 30 degrees C by the surface plating technique
2012-07-24
ISO 21569:2005/DAmd 1
* Foodstuffs — Methods of analysis for the detection of genetically modified organisms and derived products — Qualita-tive nucleic acid based methods — Amendment 1
2012-07-10
TC 35 Paints and varnishes
ISO/DIS 16474-1
* Paints and varnishes — Meth-ods of exposure to laboratory light sources — Part 1: General guidance
2012-07-17
(Revision of ISO 11341:2004, ISO 11507:2007)
ISO/DIS 16474-2
* Paints and varnishes — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
2012-07-17
(Revision of ISO 11341:2004)
ISO/DIS 16474-3
* Paints and varnishes — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps
2012-07-17
(Revision of ISO 11507:2007)
ISO/DIS 16474-4
* Paints and varnishes — Methods of exposure to laboratory light sources — Part 4: Carbon-arc lamps
2012-07-17
TC 39 Machine tools
ISO/DIS 10791-1
* Test conditions for machining centres — Part 1: Geometric tests for machines with horizon-tal spindle (horizontal Z-axis)
2012-07-15
(Revision of ISO 10791-1:1998)
ISO/DIS 10791-6
* Test conditions for machining centres — Part 6: Accuracy of speeds and interpolations
2012-07-24
(Revision of ISO 10791-6:1998, ISO 10791-6:1998/Cor 1:2004)
ISO/DIS 10791-7
* Test conditions for machining centres — Part 7: Accuracy of a finished test piece
2012-07-15
(Revision of ISO 10791-7:1998)
TC 45 Rubber and rubber products
ISO/DIS 1432.2
* Rubber, vulcanized or thermo-plastic — Determination of low-temperature stiffening (Gehman test)
2012-04-29
(Revision of ISO 1432:1988, ISO 1432:1988/Cor 1:2003)
ISO/DIS 3303-1
Rubber- or plastics-coated fab-rics — Determination of bursting strength — Part 1: Steel-ball method
2012-05-09
(Revision of ISO 3303:1990)
ISO/DIS 3303-2
Rubber- or plastics-coated fab-rics — Determination of bursting strength — Part 2: Hydraulic method
2012-05-09
(Revision of ISO 3303:1990)
TC 58 Gas cylinders
ISO/DIS 12209 * Gas cylinders — Outlet connec-tions for gas cylinder valves for compressed breathable air
2012-07-24
(Revision of ISO 12209-1:2000, ISO 12209-2:2000, ISO 12209-3:2000)
TC 59 Buildings and civil engi-neering works
ISO/DIS 16354 Guidelines for Knowledge Librar-ies and Object Libraries 2012-07-29
TC 61 Plastics
ISO 899-1:2003/DAmd 1
* Plastics — Determination of creep behaviour — Part 1: Ten-sile creep — Amendment 1
2012-07-10
ISO Update, Supplement to ISO Focus -- March 2012 7
ISO 899-2:2003/DAmd 1
* Plastics — Determination of creep behaviour — Part 2: Flex-ural creep by three-point loading — Amendment 1
2012-07-10
ISO/DIS 11357-5
* Plastics — Differential scanning calorimetry (DSC) — Part 5: Determination of characteristic reaction-curve temperatures and times, enthalpy of reaction and degree of conversion
2012-07-17
(Revision of ISO 11357-5:1999)
ISO/DIS 4892-2.2
* Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps
2012-04-10
(Revision of ISO 4892-2:2006, ISO 4892-2:2006/Amd 1:2009)
TC 68 Financial services
ISO/DIS 1004-1
* Information processing — Mag-netic ink character recognition — Part 1: Print specifications for E13B
2012-07-02
(Revision of ISO 1004:1995)
ISO/DIS 1004-2
* Information processing — Mag-netic ink character recognition — Part 2: Print specifications for CMC7
2012-07-02
TC 69 Applications of statistical methods
ISO/DIS 3951-1
* Sampling procedures for inspec-tion by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
2012-07-15
(Revision of ISO 3951-1:2005)
ISO/DIS 3951-2
* Sampling procedures for inspec-tion by variables — Part 2: General specification for single sampling plans indexed by ac-ceptance quality limit (AQL) for lot-by-lot inspection of inde-pendent quality characteristics
2012-07-15
(Revision of ISO 3951-2:2006, ISO 3951-2:2006/Amd 1:2009)
TC 71 Concrete, reinforced concrete and pre-stressed concrete
ISO/DIS 1920-11
* Testing of concrete — Part 11: Determination of the chloride resistance of concrete, unidirec-tional diffusion
2012-07-30
ISO/DIS 1920-12
* Testing of concrete — Part 12: Determination of the carbonation resistance of concrete — Accel-erated carbonation method
2012-07-30
TC 79 Light metals and their alloys
ISO/DIS 7583 Anodizing of aluminium and its alloys — Terms and definitions 2012-07-28
(Revision of ISO 7583:1986)
TC 83 Sports and recreational equipment
ISO/DIS 20957-1
* Stationary training equipment — Part 1: General safety require-ments and test methods
2012-07-10
(Revision of ISO 20957-1:2005)
TC 108 Mechanical vibration, shock and condition monitoring
ISO/DIS 20958-1
* Condition monitoring and diag-nostics of machines — Electrical signature analysis — Part 1: Three-phase induction motors
2012-07-04
TC 121 Anaesthetic and respiratory equipment
ISO/DIS 5367 * Anaesthetic and respiratory equipment — Breathing sets and connectors
2012-07-24
(Revision of ISO 5367:2000)
ISO/DIS 10079-2
* Medical suction equipment — Part 2: Manually powered suc-tion equipment
2012-07-24
(Revision of ISO 10079-2:1999)
TC 127 Earth-moving machinery
ISO/DIS 7130 * Earth-moving machinery — Guide to procedure for operator training
2012-07-04
(Revision of ISO 7130:1981)
ISO/DIS 6747 * Earth-moving machinery — Tractor-dozers — Terminology and commercial specifications
2012-07-02
(Revision of ISO 6747:1998, ISO 6747:1998/Amd 1:2003)
TC 135 Non-destructive testing
ISO/DIS 5579 * Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules
2012-07-03
(Revision of ISO 5579:1998)
TC 138 Plastics pipes, fittings and valves for the transport of fluids
ISO/DIS 18225 * Plastics piping systems — Multi-layer piping systems for outdoor gas installations — Specifica-tions for systems
2012-07-15
(Revision of ISO 18225:2007)
TC 150 Implants for surgery
ISO/DIS 16087 * Implants for surgery - Roent-gen stereophotogrammetry for assessment of micromotion of orthopaedic implants
2012-07-04
TC 156 Corrosion of metals and alloys
ISO/DIS 15158 * Corrosion of metals and alloys — Method of measuring the pitting potential for stainless steels by potentiokinetic control in sodium chloride solution
2012-07-24
TC 171 Document management applications
ISO/DIS 14739-1.2
Document management — 3D use of Product Representation Compact (PRC) format — Part 1: PRC 10001
2012-04-30
TC 172 Optics and photonics
ISO/DIS 8039.2
* Microscopes — Values, toleranc-es and symbols for magnification 2012-04-04
(Revision of ISO 8039:1997)
TC 173 Assistive products for per-sons with disability
ISO/DIS 7176-25
* Wheelchairs — Part 25: Batter-ies and chargers for powered wheelchairs - Requirements and test methods
2012-07-04
8 ISO Update, Supplement to ISO Focus -- March 2012
TC 184 Automation systems and integration
IEC/DIS 62264-1
Enterprise-control system integration — Part 1: Models and terminology
2012-07-18
(Revision of IEC 62264-1:2003)
IEC/DIS 62264-2
Enterprise-control system inte-gration — Part 2: Object model attributes
2012-07-18
(Revision of IEC 62264-2:2004)
TC 193 Natural gasISO/DIS 13734 * Natural gas — Organic com-
ponents used as odorants — Re-quirements and test methods
2012-07-24
(Revision of ISO 13734:1998, ISO 13734:1998/Cor 1:1999)
TC 204 Intelligent transport systems
ISO/DIS 15623 * Intelligent Transport Systems — Forward vehicle collision warning systems — Performance require-ments and test procedures
2012-07-24
(Revision of ISO 15623:2002)
TC 213 Dimensional and geometri-cal product specifications and verification
ISO/DIS 2538-1
* Geometrical product specifica-tions (GPS) — Wedges — Part 1: Series of angles and slopes
2012-07-17
(Revision of ISO 2538:1998)
ISO/DIS 2538-2
* Geometrical product specifica-tions (GPS) — Wedges — Part 2: Dimensioning and tolerancing
2012-07-17
(Revision of ISO 2538:1998)
ISO 14253-1:1998/DAmd 1
* Geometrical Product Specifica-tions (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for proving con-formance or non-conformance with specifications — Amend-ment 1
2012-07-03
TC 227 SpringsISO/DIS 16249 Springs — Symbols
2012-07-29
JTC 1 Information technologyISO/IEC DIS 15504-6
Information technology — Pro-cess assessment — Part 6: An exemplar system life cycle process assessment model
2012-07-25
(Revision of ISO/IEC TR 15504-6:2008, ISO/IEC TR 15504-6:2008/DAM 1)
ISO/IEC DIS 20000-3
* Information technology — Ser-vice management — Part 3: Guidance on scope definition and applicability of ISO/IEC 20000-1
2012-05-04
(Revision of ISO/IEC TR 20000-3:2009)
ISO/IEC DIS 14776-261
Information technology — Small Computer System Interface (SCSI) — Part 261: SAS Protocol Layer (SPL)
2012-07-04
ISO/IEC DIS 18046-3
* Information technology — Radio frequency identification device performance test methods — Part 3: Test methods for tag performance
2012-05-04
(Revision of ISO/IEC 18046-3:2007)
ISO/IEC DIS 18047-6
* Information technology — Radio frequency identification device conformance test methods — Part 6: Test methods for air interface communications at 860 MHz to 960 MHz
2012-05-04
(Revision of ISO/IEC TR 18047-6:2011)
ISO/IEC DIS 24730-61
Information technology — Real-time locating systems (RTLS) — Part 61: Low rate pulse repetition frequency Ultra Wide Band (UWB) air interface
2012-07-21
ISO/IEC DIS 24730-62
Information technology — Real-time locating systems (RTLS) — Part 62: High rate pulse repetition frequency Ultra Wide Band (UWB) air interface
2012-07-21
ISO/IEC DIS 24769-5
Information technology — Real-time locating system (RTLS) device conformance test meth-ods — Part 5: : Test methods for Chirp spread spectrum (CSS) air interface communication at 2,4 GHz
2012-07-21
ISO/IEC DIS 24770
Information technology — Real-time locating system (RTLS) de-vice performance test methods — Test methods for air interface communication at 2,4 GHz
2012-07-21
(Revision of ISO/IEC TR 24770:2008)
FDIS circulated
Period from 01 February to 29 February 2012
These Final draft International Standards have been submitted to the ISO member bodies for formal approval by the date shown
* Available in English only
Vote terminates
TC 4 Rolling bearings
ISO 10285:2007/FDAmd 1
* Rolling bearings — Sleeve type linear ball bearings — Boundary dimensions and tolerances — Amendment 1
2012-04-29
TC 6 Paper, board and pulps
ISO/FDIS 1974 * Paper — Determination of tear-ing resistance — Elmendorf method
2012-04-10
(Revision of ISO 1974:1990)
TC 10 Technical product documentation
ISO/FDIS 6433 * Technical product documenta-tion — Part references 2012-04-10
(Revision of ISO 6433:1981)
TC 21 Equipment for fire protec-tion and fire fighting
ISO/FDIS 7240-10
* Fire detection and alarm systems — Part 10: Point-type flame detectors
2012-04-21
(Revision of ISO 7240-10:2007)
ISO Update, Supplement to ISO Focus -- March 2012 9
ISO/FDIS 7076-1
* Fire protection - Foam fire extinguishing systems — Part 1: Foam proportioning equipment
2012-04-28
ISO/FDIS 7076-2
* Fire protection - Foam fire extin-guishing systems — Part 2: Low expansion foam equipment
2012-04-28
TC 22 Road vehicles
ISO/FDIS 11446-2
* Road vehicles — Connectors for the electrical connection of tow-ing and towed vehicles — Part 2: 13-pole connectors for vehicles with 12 V nominal supply voltage intended to cross water fords
2012-04-08
(Revision of ISO 11446:2004)
TC 34 Food products
ISO/FDIS 15163
* Milk and milk products — Calf rennet and adult bovine rennet — Determination by chromatog-raphy of chymosin and bovine pepsin contents
2012-04-02
TC 41 Pulleys and belts (including veebelts)
ISO/FDIS 5296 * Synchronous belt drives — Belts with pitch codes MXL, XXL, XL, L, H, XH and XXH — Metric and inch dimensions
2012-04-11
(Revision of ISO 5296-1:1989, ISO 5296-2:1989)
TC 42 Photography
ISO/FDIS 18933
* Imaging materials — Magnetic tape — Care and handling prac-tices for extended usage
2012-04-29
(Revision of ISO 18933:2006)
TC 44 Welding and allied processes
ISO/FDIS 13585
* Brazing — Qualification test of brazers and brazing operators 2012-04-24
ISO/FDIS 22825
* Non-destructive testing of welds — Ultrasonic testing — Testing of welds in austenitic steels and nickel-based alloys
2012-04-03
(Revision of ISO 22825:2006)
ISO/FDIS 9606-1
* Qualification testing of weld-ers — Fusion welding — Part 1: Steels
2012-04-25
(Revision of ISO 9606-1:1994, ISO 9606-1:1994/Amd 1:1998)
TC 46 Information and documentation
ISO/FDIS 27730.2
* Information and documentation — International standard collec-tion identifier (ISCI)
2012-04-04
TC 61 Plastics
ISO/FDIS 9352 * Plastics — Determination of resistance to wear by abrasive wheels
2012-04-04
(Revision of ISO 9352:1995)
TC 92 Fire safety
ISO/FDIS 14934-3
* Fire tests — Calibration and use of heat flux meters — Part 3: Secondary calibration method
2012-04-28
(Revision of ISO 14934-3:2006)
TC 94 Personal safety -- Pro-tective clothing and equipment
ISO/FDIS 4007 * Personal protective equip-ment — Eye and face protection — Vocabulary
2012-04-10
(Revision of ISO 4007:1977)
TC 115 Pumps
ISO/FDIS 17769-1
* Liquid pumps and installation — General terms, definitions, quantities, letter symbols and units — Part 1: Liquid pumps
2012-04-10
(Revision of ISO 17769:2008)
ISO/FDIS 17769-2
* Liquid pumps and installation — General terms, definitions, quantities, letter symbols and units — Part 2: Pumping system
2012-04-10
TC 147 Water quality
ISO/FDIS 12846
* Water quality — Determination of mercury — Method using atomic absorption spectrometry (AAS) with and without enrichment
2012-04-03
(Revision of ISO 5666:1999, ISO 16590:2000)
TC 150 Implants for surgery
ISO/FDIS 11658
* Cardiovascular implants and ex-tracorporeal systems — Blood/tissue contact surface modifica-tions for extracorporeal perfusion systems
2012-04-24
TC 156 Corrosion of metals and alloys
ISO/FDIS 9227 * Corrosion tests in artificial at-mospheres — Salt spray tests 2012-04-10
(Revision of ISO 9227:2006)
TC 190 Soil quality
ISO/FDIS 10930
* Soil quality — Measurement of the stability of soil aggregates subjected to the action of water
2012-04-11
TC 193 Natural gas
ISO/FDIS 6974-1
* Natural gas — Determination of composition and associated un-certainty by gas chromatography — Part 1: General guidelines and calculation of composition
2012-04-17
(Revision of ISO 6974-1:2000)
ISO/FDIS 6974-2
* Natural gas — Determination of composition and associated uncertainty by gas chromatog-raphy — Part 2: Uncertainty calculations
2012-04-17
(Revision of ISO 6974-2:2001)
TC 207 Environmental management
ISO/FDIS 14045
* Environmental management — Eco-efficiency assessment of product systems — Principles, requirements and guidelines
2012-04-03
TC 210 Quality management and corresponding general as-pects for medical devices
ISO/FDIS 15223-1
* Medical devices — Symbols to be used with medical device labels, labelling and information to be supplied — Part 1: General requirements
2012-04-24
(Revision of ISO 15223-1:2007, ISO 15223-1:2007/Amd 1:2008)
TC 215 Health informatics
ISO/FDIS 11238
* Health informatics — Identifica-tion of medicinal products — Data elements and structures for the unique identification and exchange of regulated informa-tion on substances
2012-04-24
10 ISO Update, Supplement to ISO Focus -- March 2012
ISO/FDIS 11239
* Health informatics — Identifica-tion of medicinal products — Data elements and structures for the unique identification and ex-change of regulated information on pharmaceutical dose forms, units of presentation, routes of administration and packaging
2012-04-24
ISO/FDIS 11240
* Health informatics — Identifica-tion of medicinal products — Data elements and structures for the unique identification and ex-change of units of measurement
2012-04-24
ISO/FDIS 11615
* Health informatics — Identifica-tion of medicinal products — Data elements and structures for the unique identification and exchange of regulated medicinal product information
2012-04-24
ISO/FDIS 11616
* Health informatics — Identifica-tion of medicinal products — Data elements and structures for the unique identification and exchange of regulated pharma-ceutical product information
2012-04-24
TC 217 Cosmetics
ISO/FDIS 24443
* Determination of sunscreen UVA photoprotection in vitro 2012-04-24
TC 223 Societal security
ISO/FDIS 22300
* Societal security — Terminology2012-04-02
ISO/FDIS 22301
* Societal security — Business continuity management systems --- Requirements
2012-04-02
JTC 1 Information technology
ISO/IEC FDIS 10646
* Information technology — Uni-versal Coded Character Set (UCS)
2012-04-14
(Revision of ISO/IEC 10646:2011)
ISO/IEC 10373-6:2011/FDAmd 3
* Identification cards — Test meth-ods — Part 6: Proximity cards — Amendment 3: Exchange of additional parameters, block numbering, unmatched AFI and TR2
2012-03-31
ISO/IEC 14443-4:2008/FDAmd 2
* Identification cards — Contact-less integrated circuit cards — Proximity cards — Part 4: Trans-mission protocol — Amendment 2: Bit rates of fc/8, fc/4 and fc/2, protocol activation of PICC Type A and frame size from 512 bytes to 4 096 bytes
2012-04-17
ISO/IEC FDIS 30170
* Information technology — Pro-gramming languages — Ruby 2012-04-01
ISO/IEC 18023-1:2006/FDAmd 1
* Information technology — SE-DRIS — Part 1: Functional speci-fication — Amendment 1
2012-04-16
ISO/IEC 18023-3:2006/FDAmd 1
* Information technology — SE-DRIS — Part 3: Transmittal for-mat binary encoding — Amend-ment 1
2012-04-16
ISO/IEC 18024-4:2006/FDAmd 1
* Information technology — SE-DRIS language bindings — Part 4: C — Amendment 1
2012-04-16
ISO/IEC 14888-3:2006/FDAmd 2
* Information technology — Se-curity techniques — Digital signatures with appendix — Part 3: Discrete logarithm based mechanisms — Amendment 2: Optimizing hash inputs
2012-04-14
ISO/IEC FDIS 27033-2
* Information technology — Se-curity techniques — Network security — Part 2: Guidelines for the design and implementation of network security
2012-04-17
(Revision of ISO/IEC 18028-2:2006)
ISO/IEC FDIS 29192-3
* Information technology — Se-curity techniques — Lightweight cryptography — Part 3: Stream ciphers
2012-04-17
ISO/IEC 14496-12:2008/FDAmd 2
* Information technology — Cod-ing of audio-visual objects — Part 12: ISO base media file format — Amendment 2
2012-04-24
ISO/IEC 15444-12:2008/FDAmd 2
* Information technology — JPEG 2000 image coding system — Part 12: ISO base media file format — Amendment 2
2012-04-24
ISO/IEC 15938-9:2005/FDAmd 1
* Information technology — Mul-timedia content description inter-face — Part 9: Profiles and levels — Amendment 1: Extensions to profiles and levels
2012-04-24
ISO/IEC FDIS 20944-1
* Information technology — Meta-data Registries Interoperability and Bindings (MDR-IB) — Part 1: Framework, common vocabu-lary, and common provisions for conformance
2012-04-10
ISO/IEC FDIS 20944-2
* Information technology — Meta-data Registries Interoperability and Bindings (MDR-IB) — Part 2: Coding bindings
2012-04-10
ISO/IEC FDIS 20944-3
* Information technology — Meta-data Registries Interoperability and Bindings (MDR-IB) — Part 3: API bindings
2012-04-10
ISO/IEC FDIS 20944-4
* Information technology — Meta-data Registries Interoperability and Bindings (MDR-IB) — Part 4: Protocol bindings
2012-04-10
ISO/IEC FDIS 20944-5
* Information technology — Meta-data Registries Interoperability and Bindings (MDR-IB) — Part 5: Profiles
2012-04-10
ISO/IEC FDIS 9541-1
* Information technology — Font information interchange — Part 1: Architecture
2012-04-01
(Revision of ISO/IEC 9541-1:1991, ISO/IEC 9541-1:1991/Cor 1:1992, ISO/IEC 9541-1:1991/Cor 2:1994, ISO/IEC 9541-1:1991/Amd 1:2001, ISO/IEC 9541-1:1991/Amd 2:1998, ISO/IEC 9541-1:1991/Cor 3:1995, ISO/IEC 9541-1:1991/Amd 3:2000, ISO/IEC 9541-1:1991/Amd 4:2009)
ISO/IEC FDIS 9541-2
* Information technology — Font information interchange — Part 2: Interchange format
2012-04-01
(Revision of ISO/IEC 9541-2:1991, ISO/IEC 9541-2:1991/Cor 1:1993, ISO/IEC 9541-2:1991/Cor 2:1995, ISO/IEC 9541-2:1991/Amd 1:2000, ISO/IEC 9541-2:1991/Amd 2:2009)
ISO Update, Supplement to ISO Focus -- March 2012 11
ISO/IEC FDIS 9541-3
* Information technology — Font information interchange — Part 3: Glyph shape representation
2012-04-01
(Revision of ISO/IEC 9541-3:1994, ISO/IEC 9541-3:1994/Amd 1:2005, ISO/IEC 9541-3:1994/Amd 2:2009)
ISO/IEC FDIS 19788-5
* Information technology — Learn-ing, education and training — Metadata for learning resources — Part 5: Educational elements
2012-04-14
Standards published
New International Standards published between 01 February and 29 February 2012
* Available in English only
** French version of standard previously published in English only
Price group
TC 20 Aircraft and space vehicles
ISO 16363:2012
* Space data and information transfer systems — Audit and certification of trustworthy digital repositories
V
ISO 15388:2012
* Space systems — Contamination and cleanliness control K
TC 21 Equipment for fire protection and fire fighting
ISO 21927-9:2012
* Smoke and heat control systems — Part 9: Specification for control equipment
V
TC 22 Road vehicles
ISO 13207-1:2012
* Road vehicles — LED lamp charac-teristics for bulb compatible failure detection — Part 1: LED lamps used as direction indicators
C
ISO/TS 19072-3:2012
* Road vehicles — Connection interface for pyrotechnic devices, two-way and three-way connections — Part 3: Pyro-technic device and harness connector assembly - type 1
D
TC 23 Tractors and machinery for agri-culture and forestry
ISO/TS 11356:2011
Crop protection equipment — Trace-ability — Spray parameter recording J
ISO 15886-1:2012
* Agricultural irrigation equipment — Sprinklers — Part 1: Definition of terms and classification
H
ISO 11783-2:2012
Tractors and machinery for agriculture and forestry — Serial control and com-munications data network — Part 2: Physical layer
T
TC 29 Small tools
ISO 6987:2012 Indexable hard material inserts with rounded corners, with partly cylindrical fixing hole — Dimensions
L
ISO 3316:2012 Assembly tools for screws and nuts — Attachments for hand-operated square drive socket wrenches — Dimensions and tests
C
TC 31 Tyres, rims and valvesISO 9413:2012 * Tyre valves — Dimensions and
designation XA
TC 35 Paints and varnishesISO 8503-1:2012
Preparation of steel substrates before application of paints and related prod-ucts — Surface roughness character-istics of blast-cleaned steel substrates — Part 1: Specifications and defini-tions for ISO surface profile compara-tors for the assessment of abrasive blast-cleaned surfaces
D
ISO 8503-2:2012
Preparation of steel substrates before application of paints and related products — Surface roughness characteristics of blast-cleaned steel substrates — Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel — Comparator procedure
B
ISO 8503-3:2012
Preparation of steel substrates before application of paints and related prod-ucts — Surface roughness character-istics of blast-cleaned steel substrates — Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Focusing microscope procedure
F
ISO 8503-4:2012
Preparation of steel substrates before application of paints and related prod-ucts — Surface roughness character-istics of blast-cleaned steel substrates — Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile — Stylus instrument procedure
E
TC 39 Machine toolsISO 230-1:2012
Test code for machine tools — Part 1: Geometric accuracy of machines operating under no-load or quasi-static conditions
XC
TC 43 AcousticsISO 3743-1:2010
Acoustics — Determination of sound power levels and sound energy levels of noise sources using sound pres-sure — Engineering methods for small movable sources in reverberant fields — Part 1: Comparison method for a hard-walled test room
R
ISO/PAS 17208-1:2012
* Acoustics — Quantities and proce-dures for description and measurement of underwater sound from ships — Part 1: General requirements for measure-ments in deep water
L
TC 44 Welding and allied processesISO 14174:2012
Welding consumables — Fluxes for submerged arc welding and electroslag welding — Classification
H
ISO 15614-1:2004/Amd 2:2012
Specification and qualification of weld-ing procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys — Amendment 2
XZ
TC 61 PlasticsISO 527-1:2012
Plastics — Determination of tensile properties — Part 1: General principles L
12 ISO Update, Supplement to ISO Focus -- March 2012
ISO 527-2:2012
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
F
ISO 1133-1:2011
Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method
M
ISO 1622-1:2012
Plastics — Polystyrene (PS) mould-ing and extrusion materials — Part 1: Designation system and basis for specifications
B
ISO 17212:2012
* Structural adhesives — Guidelines for the surface preparation of metals and plastics prior to adhesive bonding
M
TC 67 Materials, equipment and off-shore structures for petroleum, petrochemical and natural gas industries
ISO 14224:2006
Petroleum, petrochemical and natural gas industries — Collection and ex-change of reliability and maintenance data for equipment
XC
ISO 10414-2:2011
Petroleum and natural gas industries — Field testing of drilling fluids — Part 2: Oil-based fluids
XC
ISO 13628-4:2010
Petroleum and natural gas industries — Design and operation of subsea production systems — Part 4: Subsea wellhead and tree equipment
XC
ISO 19901-3:2010
Petroleum and natural gas industries — Specific requirements for offshore structures — Part 3: Topsides structure
XA
TC 69 Applications of statistical methods
ISO 7870-3:2012
* Control charts — Part 3: Acceptance control charts K
TC 71 Concrete, reinforced concrete and pre-stressed concrete
ISO 13315-1:2012
* Environmental management for con-crete and concrete structures — Part 1: General principles
G
TC 76 Transfusion, infusion and injection, and blood process-ing equipment for medical and pharmaceutical use
ISO 1135-4:2012
* Transfusion equipment for medical use — Part 4: Transfusion sets for single use
H
TC 85 Nuclear energy, nuclear tech-nologies, and radiological protection
ISO 2919:2012 Radiological protection — Sealed radioactive sources — General require-ments and classification
K
TC 92 Fire safety
ISO 5658-2:2006/Amd 1:2011
Reaction to fire tests — Spread of flame — Part 2: Lateral spread on building and transport products in ver-tical configuration — Amendment 1
XZ
ISO 16732-1:2012
Fire safety engineering — Fire risk as-sessment — Part 1: General K
TC 96 Cranes
ISO 11660-4:2012
* Cranes — Access, guards and re-straints — Part 4: Jib cranes C
TC 106 Dentistry
ISO 9693-1:2012
Dentistry — Compatibility testing — Part 1: Metal-ceramic systems C
IEC 80601-2-60:2012
* Medical electrical equipment — Part 2-60: Particular requirements for basic safety and essential performance of dental equipment
V
TC 108 Mechanical vibration, shock and condition monitoring
ISO 13374-3:2012
* Condition monitoring and diagnostics of machines — Data processing, com-munication and presentation — Part 3: Communication
L
TC 110 Industrial trucks
ISO 22915-13:2012
Industrial trucks — Verification of sta-bility — Part 13: Rough-terrain trucks with mast
C
TC 121 Anaesthetic and respiratory equipment
ISO 81060-2:2009
Non-invasive sphygmomanometers — Part 2: Clinical validation of automated measurement type
Q
TC 123 Plain bearings
ISO/TR 4378-6:2012
Plain bearings — Terms, definitions, classification and symbols — Part 6: Abbreviated terms
C
TC 130 Graphic technology
ISO 16684-1:2012
* Graphic technology — Extensible metadata platform (XMP) specification — Part 1: Data model, serialization and core properties
S
TC 131 Fluid power systems
ISO 3601-1:2012
Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes
R
TC 145 Graphical symbols
ISO 3864-3:2012
Graphical symbols — Safety colours and safety signs — Part 3: Design principles for graphical symbols for use in safety signs
N
TC 146 Air quality
ISO 13138:2012
Air quality — Sampling conventions for airborne particle deposition in the human respiratory system
J
TC 147 Water quality
ISO/TS 28581:2012
Water quality — Determination of selected non-polar substances — Method using gas chromatography with mass spectrometric detection (GC-MS)
M
ISO 8692:2012 Water quality — Fresh water algal growth inhibition test with unicellular green algae
L
TC 150 Implants for surgery
ISO 7199:2009/Amd 1:2012
* Cardiovascular implants and artificial organs — Blood-gas exchangers (oxy-genators) — Amendment 1: Clarifica-tions for test methodologies, labelling, and sampling schedule
XZ
ISO 27185:2012
* Cardiac rhythm management devices — Symbols to be used with cardiac rhythm management device labels, and information to be supplied — General requirements
P
ISO Update, Supplement to ISO Focus -- March 2012 13
TC 157 Non-systemic contraceptives and STI barrier prophylactics
ISO 8009:2004/Amd 1:2012
* Mechanical contraceptives — Reus-able natural and silicone rubber contra-ceptive diaphragms — Requirements and tests — Amendment 1
XZ
TC 159 Ergonomics
ISO 9241-143:2012
Ergonomics of human-system interac-tion — Part 143: Forms X
TC 163 Thermal performance and en-ergy use in the built environment
ISO 10077-2:2012
* Thermal performance of windows, doors and shutters — Calculation of thermal transmittance — Part 2: Nu-merical method for frames
R
TC 184 Automation systems and integration
ISO 8373:2012 * Robots and robotic devices — Vocabulary R
TC 190 Soil quality
ISO 11063:2012
Soil quality — Method to directly ex-tract DNA from soil samples L
ISO 11269-1:2012
Soil quality — Determination of the ef-fects of pollutants on soil flora — Part 1: Method for the measurement of inhibition of root growth
H
TC 198 Sterilization of health care products
ISO 20857:2010
Sterilization of health care products — Dry heat — Requirements for the development, validation and routine control of a sterilization process for medical devices
U
TC 204 Intelligent transport systems
ISO 12855:2012
* Electronic fee collection — Information exchange between service provision and toll charging
W
ISO/TS 13140-2:2012
* Electronic fee collection — Evaluation of on-board and roadside equipment for conformity to ISO/TS 13141 — Part 2: Abstract test suite
H
ISO 14814:2006
Road transport and traffic telematics — Automatic vehicle and equipment identification — Reference architecture and terminology
F
ISO/TS 16401-1:2012
* Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-2 — Part 1: Test suite structure and test purposes
XC
ISO/TS 16401-2:2012
* Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-2 — Part 2: Abstract test suite
E
ISO/TS 16403-1:2012
* Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-4 — Part 1: Test suite structure and test purposes
T
ISO/TS 16403-2:2012
* Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-4 — Part 2: Abstract test suite
F
ISO/TS 16407-2:2012
* Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-1 — Part 2: Abstract test suite
F
ISO/TS 16410-2:2012
* Electronic fee collection — Evaluation of equipment for conformity to ISO/TS 17575-3 — Part 2: Abstract test suite
F
TC 211 Geographic information/Geomatics
ISO 19144-1:2009
Geographic information — Classifica-tion systems — Part 1: Classification system structure
P
ISO 19148:2012
* Geographic information — Linear referencing X
CASCO Committee on conformity assessment
ISO/IEC 17020:2012
Conformity assessment — Require-ments for the operation of various types of bodies performing inspection
J
JTC 1 Information technology
ISO/IEC 14908-2:2012
* Information technology — Control net-work protocol — Part 2: Twisted pair communication
H
ISO/IEC 14908-3:2012
* Information technology — Control network protocol — Part 3: Power line channel specification
G
ISO/IEC 14908-4:2012
* Information technology — Con-trol network protocol — Part 4: IP communication
U
ISO/IEC 20000-2:2012
* Information technology — Service management — Part 2: Guidance on the application of service management systems
X
ISO/IEC 23271:2012
* Information technology — Common Language Infrastructure (CLI) XC
ISO/IEC 14543-5-3:2012
* Information technology — Home electronic system (HES) architecture — Part 5-3: Intelligent grouping and resource sharing for HES Class 2 and Class 3 — Basic application
H
ISO/IEC 14543-5-5:2012
* Information technology — Home electronic system (HES) architecture — Part 5-5: Intelligent grouping and resource sharing for HES Class 2 and Class 3 — Device type
G
ISO/IEC 14543-5-6:2012
* Information technology — Home electronic system (HES) architecture — Intelligent grouping and resource sharing for HES Class 2 and Class 3 — Part 5-6: Service type
XC
ISO/IEC 14543-5-21:2012
* Information technology — Home electronic system (HES) architecture — Part 5-21: Intelligent grouping and resource sharing for HES Class 2 and Class 3 — Application profile — AV profile
T
ISO/IEC 14763-2:2012
* Information technology — Imple-mentation and operation of customer premises cabling — Part 2: Planning and installation
XB
ISO/IEC 28360:2012
* Information technology — Office equipment — Determination of chemi-cal emission rates from electronic equipment
S
14 ISO Update, Supplement to ISO Focus -- March 2012
Standards confirmed
The following International Standards are confimred for a five year period:
TC 8 Ships and marine technology
ISO 3902:1990 (reconfirmed)
ISO 7462:1985 (reconfirmed)
TC 23 Tractors and machinery for agriculture and forestry
ISO 4254-5:2008
ISO 5131:1996 (reconfirmed)
TC 33 Refractories
ISO 21068-1:2008
ISO 21068-2:2008
ISO 21068-3:2008
TC 34 Food products
ISO 14501:2007
TC 38 Textiles
ISO 105-A06:1995 (reconfirmed)
ISO 105-A08:2001 (reconfirmed)
ISO 105-B08:1995 (reconfirmed)
ISO 105-F01:2001 (reconfirmed)
ISO 105-F03:2001 (reconfirmed)
ISO 105-F04:2001 (reconfirmed)
ISO 105-F05:2001 (reconfirmed)
ISO 105-F07:2001 (reconfirmed)
ISO 105-Z04:1995 (reconfirmed)
ISO 105-Z07:1995 (reconfirmed)
ISO 105-Z08:1995 (reconfirmed)
ISO 105-Z09:1995 (reconfirmed)
TC 41 Pulleys and belts (including veebelts)
ISO 9563:1990 (reconfirmed)
TC 45 Rubber and rubber products
ISO 15671:2000 (reconfirmed)
TC 58 Gas cylinders
ISO 10692-1:2001 (reconfirmed)
TC 67 Materials, equipment and offshore structures for petroleum, petrochemi-cal and natural gas industries
ISO 15663-1:2000 (reconfirmed)
ISO 15663-2:2001 (reconfirmed)
ISO 15663-3:2001 (reconfirmed)
TC 70 Internal combustion engines
ISO 6798:1995 (reconfirmed)
TC 72 Textile machinery and accessories
ISO 5249:1988 (reconfirmed)
ISO 11659-1:1995 (reconfirmed)
TC 85 Nuclear energy, nuclear technologies, and radiological protection
ISO 7212:1986 (reconfirmed)
ISO 8529-1:2001 (reconfirmed)
ISO 9404-1:1991 (reconfirmed)
ISO 11933-4:2001 (reconfirmed)
ISO 11933-5:2001 (reconfirmed)
ISO 15080:2001 (reconfirmed)
TC 131 Fluid power systems
ISO 6020-1:2007
ISO 13726:2008
TC 133 Sizing systems and designations for clothes
ISO 4415:1981 (reconfirmed)
TC 166 Ceramic ware, glassware and glass ceramic ware in contact with food
ISO 6486-1:1999
ISO 6486-2:1999
ISO 7086-1:2000
ISO 7086-2:2000
ISO 8391-1:1986
ISO 8391-2:1986
TC 219 Floor coverings
ISO 8543:1998 (reconfirmed)
ISO 11858:1999 (reconfirmed)
ISO 11859:1999 (reconfirmed)
ISO 11860:1999 (reconfirmed)
ISO 17504:1999 (reconfirmed)
ISO 24337:2006
JTC 1 Information technology
ISO/IEC 2382-7:2000
(reconfirmed)
ISO 3866:1977 (reconfirmed)
ISO 4341:1978 (reconfirmed)
Standards withdrawn
Period from 01 February to 29 February 2012
TC 69 Applications of statistical methods
ISO 7966:1993 (replaced by ISO 7870-3:2012)
TC 92 Fire safety
ISO/TS 16732:2005
(replaced by ISO 16732-1:2012)
TC 159 Ergonomics
ISO 9241-17:1998 (replaced by ISO 9241-143:2012)
JTC 1 Information technology
ISO/IEC 6592:2000 (replaced by ISO/IEC 26514:2008)
IEC 559:1989 (replaced by ISO/IEC/IEEE 60559:2011)
ISO/IEC TR 14763-2:2000
(replaced by ISO/IEC 14763-2:2012)
ISO Update, Supplement to ISO Focus -- March 2012 15
Meeting calendar
(update at 01 February 2012)
Meetings called for the month of January are not in this edition.
* Information definite but meeting not yet formally convened
** Provisional
April 2012
16 Durban (South Africa)
TC 135/SC 9 Non-destructive test-ing/Acoustic emission testing
16-17 Graz (Austria) TC 24/SC 4 Particle charac-terization includ-ing sieving/Particle characterization
16-20 La Plaine St-Denis (France)
TC 198 Sterilization of health care products
16-20 Melbourne (Australia)
** TC 204 Intelligent transport systems
16-20 Chicago (USA) TC 248 Project committee: Sustainability criteria for bioenergy
17 Senlis (France) TC 117 Fans
17 Durban (South Africa)
TC 135/SC 3 Non-destructive test-ing/Ultrasonic testing
17 Durban (South Africa)
TC 135/SC 5 Non-destructive testing/Radiation methods
17-19 Montreal (Canada)
TC 232 Learning services for non-formal education and training
18 Milan (Italy) TC 44/SC 9 Welding and allied processes/Health and safety
18 Durban (South Africa)
TC 135/SC 2 Non-destructive test-ing/Surface methods
18 Durban (South Africa)
TC 135/SC 6 Non-destructive test-ing/Leak detection methods
18 Durban (South Africa)
TC 135/SC 8 Non-destructive test-ing/Infrared thermog-raphy for non-de-structive testing
18 Glasgow, Scotland (United Kingdom)
TC 161 Control and protec-tive devices for gas and/or oil burners and appliances
19 Durban (South Africa)
TC 135/SC 7 Non-destructive testing/Personnel qualification
19-20 Toulouse (France)
TC 34/SC 12 Food products/Sen-sory analysis
20 Deerfield (USA) TC 84 Devices for adminis-tration of medicinal products and intra-vascular catheters
20 Durban (South Africa)
TC 135 Non-destructive testing
23-26 Prague (Czech Republic)
TC 83/SC 5 Sports and recrea-tional equipment/Ice hockey equipment and facilities
23-26 Cape Town (South Africa)
** TC 102 Iron ore and direct reduced iron
23-27 Oslo (Norway) ** TC 59/SC 14 Buildings and civil engineering works/Design life
23-27 Winterthur (Switzerland)
TC 108/SC 2 Mechanical vibration, shock and condition monitoring/Measure-ment and evalua-tion of mechanical vibration and shock as applied to ma-chines, vehicles and structures
25 Yokohama (Japan)
TC 4/SC 4 Rolling bearings/Tolerances, tolerance definitions and sym-bols (including GPS)
26-27 Nairobi (Kenya) TC 34 Food products
26-27 Moscow (Rus-sian Federation)
TC 67/SC 2 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Pipeline transporta-tion systems
26-27 Vienna (Austria) TC 159 Ergonomics
27 Yokohama (Japan)
TC 4/SC 12 Rolling bearings/Ball bearings
27 Thessalonik (Greece)
TC 92/SC 3 Fire safety/Fire threat to people and environment
27 Thessalonik (Greece)
TC 92/SC 4 Fire safety/Fire safety engineering
May 2012
1-4 Jeju (Korea, Republic of)
* TC 28 Petroleum products and lubricants
2 Jeju (Korea, Republic of)
* TC 28/SC 5 Petroleum products and lubricants/Meas-urement of refriger-ated hydrocarbon and non-petroleum based liquefied gaseous fuels
3 Dublin (Ireland) ** TC 242 Energy Management
6-9 Vancouver (Canada)
TC 215 Health informatics
7 Ittigen (Switzerland)
TC 113/SC 1 Hydrometry/Velocity area methods
7-10 Berlin (Germany) TC 22/SC 13 Road vehicles/Ergo-nomics applicable to road vehicles
7-11 Berlin (Germany) ** TC 46 Information and documentation
7-11 Berlin (Germany) TC 46/SC 4 Information and documentation/Tech-nical interoperability
7-11 Berlin (Germany) * TC 46/SC 11 Information and doc-umentation/Archives/records management
7-11 Ittigen (Switzerland)
TC 113 Hydrometry
8 Ittigen (Switzerland)
TC 113/SC 5 Hydrometry/In-struments, equip-ment and data management
16 ISO Update, Supplement to ISO Focus -- March 2012
8-10 Sydney (Australia)
TC 145/SC 1 Graphical symbols/Public information symbols
9 Berlin (Germany) ** TC 44/SC 9 Welding and allied processes/Health and safety
9 Sydney (Australia)
TC 145/SC 2 Graphical symbols/Safety identification, signs, shapes, sym-bols and colours
9-10 Haifa (Israel) TC 184/SC 5 Automation systems and integration/Inter-operability, integra-tion, and architec-tures for enterprise systems and automa-tion applications
10 Berlin (Germany) TC 24/SC 8 Particle characteriza-tion including sieving/Test sieves, sieving and industrial screens
10 Chicago (USA) ** TC 68 Financial services
10 Chicago (USA) * TC 68 Financial services
10 Ittigen (Switzerland)
TC 113/SC 6 Hydrometry/Sediment transport
10 Ittigen (Switzerland)
TC 113/SC 8 Hydrometry/Ground water
10 Sydney (Australia)
TC 145 Graphical symbols
10 Stockholm (Sweden)
TC 238 Solid biofuels
11 Berlin (Germany) TC 24 Particle characteriza-tion including sieving
14-15 Stockholm (Sweden)
* JTC 1/SC 27 Information tech-nology/IT Security techniques
14-15 Rio de Janeiro (Brazil)
** TC 67/SC 4 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Drilling and produc-tion equipment
14-17 Nadi (Fiji) * COPOLCO Committee on con-sumer policy
14-18 Campos do Jordão (Brazil)
TC 20/SC 14 Aircraft and space ve-hicles/Space systems and operations
14-18 Hangzhou (China)
* TC 39/SC 2 Machine tools/Test conditions for metal cutting machine tools
15-16 Luzern (Switzerland)
TC 23/SC 3 Tractors and machin-ery for agriculture and forestry/Safety and comfort
15-16 Paris (France) TC 259 Project committee: Outsourcing
15-17 Buenos Aires (Argentina)
TC 67/SC 5 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Casing, tubing and drill pipe
16 Milan (Italy) * TC 136 Furniture
17 Orlando (USA) TC 10/SC 6 Technical product documentation/Me-chanical engineering documentation
18 Orlando (USA) TC 10 Technical product documentation
20-25 Jeju (Korea, Republic of)
* JTC 1/SC 7 Information technol-ogy/Software and systems engineering
21 Mississauga (Canada)
TC 171/SC 2 Document manage-ment applications/Application issues
21-23 Shanghai (China) TC 131/SC 6 Fluid power systems/Contamination control
21-24 Daejon (Korea, Republic of)
* TC 249 Traditional chinese medicine
21-25 Berlin (Germany) ** JTC 1/SC 38 Information tech-nology/Distributed application platforms and services (DAPS)
21-25 Mississauga (Canada)
TC 171 Document manage-ment applications
22 Delft (Netherlands)
** TC 195 Building construc-tion machinery and equipment
22 Delft (Netherlands)
TC 195/SC 1 Building construc-tion machinery and equipment/Machinery and equipment for concrete work
23 Tokyo (Japan) TC 173/SC 7 Assistive products for persons with disabil-ity/Accessible design
23-24 Düsseldorf (Germany)
TC 44/SC 10 Welding and allied processes/Unification of requirements in the field of metal welding
23-24 Pau (France) * TC 67/SC 7 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Offshore structures
23-25 Mississauga (Canada)
* TC 171/SC 1 Document manage-ment applications/Quality
24 Seoul (Korea, Republic of)
TC 122/SC 4 Packaging/Packaging and Environment
24 Tokyo (Japan) ** TC 173 Assistive products for persons with disability
24 Tokyo (Japan) * TC 268/SC 1 Sustainable develop-ment in communities/Smart urban infra-structure metrics
24-25 Paris (France) * TC 17/SC 3 Steel/Steels for struc-tural purposes
24-25 Toronto (Canada) TC 171/SC 3 Document manage-ment applications/General issues
25 Seoul (Korea, Republic of)
TC 44/SC 12 Welding and allied processes/Soldering materials
25 Delft (Netherlands)
* TC 195 Building construc-tion machinery and equipment
25 Seoul (Korea, Republic of)
** TC 228 Tourism and related services
May-June 2012
28-1 Helsinki (Finland) ** TC 35 Paints and varnishes
28-1 Helsinki (Finland) ** TC 35/SC 9 Paints and varnishes/General test meth-ods for paints and varnishes
ISO Update, Supplement to ISO Focus -- March 2012 17
28-1 Helsinki (Finland) ** TC 35/SC 12 Paints and varnishes/Preparation of steel substrates before ap-plication of paints and related products
28-1 Helsinki (Finland) ** TC 35/SC 14 Paints and varnishes/Protective paint systems for steel structures
28-1 Milan (Italy) TC 173/SC 1 Assistive products for persons with disability/Wheelchairs
28-1 Bogota (Colombia)
TC 223 Societal security
31-1 Paris (France) TC 44/SC 8 Welding and allied processes/Equip-ment for gas welding, cutting and allied processes
31-1 London (United Kingdom)
TC 67/SC 6 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Processing equip-ment and systems
June 2012
4-5 Berlin (Germany) TC 44/SC 3 Welding and allied processes/Welding consumables
4-7 Paris (France) * TC 85/SC 5 Nuclear energy, nuclear technolo-gies, and radiological protection/Nuclear fuel cycle
4-7 Paris (France) * TC 85/SC 6 Nuclear energy, nuclear technolo-gies, and radiological protection/Reactor technology
5-6 Paris (France) TC 265 Carbon capture and storage (CCS)
7 Berlin (Germany) TC 44/SC 7 Welding and allied processes/Represen-tation and terms
7 Paris (France) TC 85/SC 2 Nuclear energy, nuclear technologies, and radiological pro-tection/Radiological protection
7-8 Toulouse (France)
TC 211 Geographic in-formation/Geomatics
8 Paris (France) TC 85 Nuclear energy, nuclear technolo-gies, and radiological protection
9 Berlin (Germany) TC 96 Cranes
10-15 Stockholm (Sweden)
TC 184/SC 4 Automation systems and integration/Indus-trial data
11-13 Woods Hole (USA)
TC 43/SC 3 Acoustics/Underwa-ter acoustics
11-13 Dresden (Germany)
* TC 126 Tobacco and tobacco products
11-15 Kyoto (Japan) TC 121 Anaesthetic and res-piratory equipment
11-15 Kyoto (Japan) TC 121/SC 1 Anaesthetic and res-piratory equipment/Breathing attach-ments and anaes-thetic machines
11-15 Kyoto (Japan) TC 121/SC 2 Anaesthetic and res-piratory equipment/Airways and related equipment
11-15 Stresa (Italy) TC 229 Nanotechnologies
11-15 Prague (Czech Republic)
TC 251 Project committee: Asset management
11-16 La Plaine St-Denis (France)
TC 147 Water quality
12-13 (France) ** TC 17/SC 17 Steel/Steel wire rod and wire products
13 Brugge (Belgium) * TC 86/SC 6 Refrigeration and air-conditioning/Testing and rating of air-conditioners and heat pumps
13 La Plaine St-Denis (France)
TC 147/SC 3 Water quality/Radio-logical methods
13-14 Geneva (Switzerland)
* TMB Technical Manage-ment Board
14 Westminster, Colorado (USA)
** TC 67/SC 3 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Drilling and comple-tion fluids, and well cements
14-15 (Europe) ** TC 91 Surface active agents
16-22 Tokyo (Japan) ** TC 69 Applications of statis-tical methods
19-22 Vienna (Austria) * REMCO Committee on refer-ence materials
19-22 San José (Costa Rica)
* TC 71 Concrete, reinforced concrete and pre-stressed concrete
19-22 San José (Costa Rica)
* TC 71/SC 1 Concrete, reinforced concrete and pre-stressed concrete/Test methods for concrete
19-22 San José (Costa Rica)
* TC 71/SC 4 Concrete, reinforced concrete and pre-stressed concrete/Performance require-ments for structural concrete
19-22 San José (Costa Rica)
* TC 71/SC 5 Concrete, reinforced concrete and pre-stressed concrete/Simplified design standard for concrete structures
19-22 San José (Costa Rica)
* TC 71/SC 6 Concrete, reinforced concrete and pre-stressed concrete/Non-traditional rein-forcing materials for concrete structures
19-22 San José (Costa Rica)
* TC 71/SC 8 Concrete, reinforced concrete and pre-stressed concrete/En-vironmental manage-ment for concrete and concrete structures
18 ISO Update, Supplement to ISO Focus -- March 2012
20 Yangzhou (China)
TC 100 Chains and chain sprockets for power transmission and conveyors
20-21 Paris (France) TC 17/SC 11 Steel/Steel castings
20-21 Milan (Italy) ** TC 29/SC 10 Small tools/Assem-bly tools for screws and nuts, pliers and nippers
21-22 Paris (France) TC 22/SC 3 Road vehicles/Elec-trical and electronic equipment
22 Porto (Portugal) * TC 87 Cork
22 Kruger Park (South Africa)
TC 110/SC 4 Industrial trucks/Rough-terrain trucks
24-29 Madrid (Spain) * TC 37 Terminology and other language and content resources
24-30 Bangkok (Thailand)
TC 207 Environmental management
25-29 Brussels (Belgium)
* TC 34/SC 9 Food products/Microbiology
25-29 Madrid (Spain) * TC 37/SC 2 Terminology and other language and content resources/Terminographical and lexicographical work-ing methods
25-29 St Paul, Min-nesota (USA)
* TC 94/SC 6 Personal safety -- Protective clothing and equipment/Eye and face protection
25-29 Buffalo (USA) TC 108 Mechanical vibration, shock and condition monitoring
25-29 Buffalo (USA) TC 108/SC 3 Mechanical vibration, shock and condition monitoring/Use and calibration of vibration and shock measuring instruments
26-27 Düsseldorf (Germany)
* TC 17/SC 9 Steel/Tinplate and blackplate
26-27 Berlin (Germany) TC 153/SC 2 Valves/Valve actuator attachment
26-27 Beijing (China) TC 263 Coalbed methane (CBM)
26-29 Beijing (China) * TC 20/SC 9 Aircraft and space vehicles/Air cargo and ground equipment
28 Buffalo (USA) TC 108/SC 6 Mechanical vibration, shock and condition monitoring/Vibration and shock generating systems
29 Paris (France) * TC 44/SC 6 Welding and allied processes/Resistance welding and allied mechanical joining
29 Madison (USA) TC 149/SC 1 Cycles/Cycles and major sub-assemblies
29 Oranjewoud (Netherlands)
TC 188 Small craft
July 2012
16 Denver (USA) * TC 44/SC 10 Welding and allied processes/Unification of requirements in the field of metal welding
18 Denver (USA) ** TC 44/SC 11 Welding and allied processes/Qualifica-tion requirements for welding and allied processes personnel
19 Berlin (Germany) TC 261 Additive manufacturing
19-20 Denver (USA) ** TC 44 Welding and allied processes
20 Lancaster (USA) ** TC 43/SC 2 Acoustics/Building acoustics
21 Stockholm (Sweden)
** JTC 1/SC 29 Information technol-ogy/Coding of audio, picture, multimedia and hypermedia information
August 2012
22-24 Berlin (Germany) * TC 212 Clinical laboratory testing and in vitro di-agnostic test systems
27-31 Montreal (Canada)
** JTC 1/SC 35 Information technol-ogy/User interfaces
September 2012
3-7 La Rochelle (France)
** TC 163 Thermal performance and energy use in the built environment
3-7 La Rochelle (France)
** TC 205 Building environment design
7 Zurich (Switzerland)
** TC 142 Cleaning equipment for air and other gases
8-16 Busan (Korea, Republic of)
* JTC 1/SC 36 Information tech-nology/Information technology for learn-ing, education and training
10 Milan (Italy) * TC 21/SC 2 Equipment for fire protection and fire fighting/Manu-ally transportable fire extinguishers
10-11 Geneva (Switzerland)
* JTC 1/SC 22 Information technol-ogy/Programming languages, their envi-ronments and system software interfaces
10-12 Shandong (China)
* TC 206 Fine ceramics
10-14 Nancy (France) TC 108/SC 4 Mechanical vibration, shock and condition monitoring/Human exposure to me-chanical vibration and shock
10-14 La Plaine St-Denis (France)
* TC 153/SC 1 Valves/Design, manu-facture, marking and testing
10-14 Helsinki (Finland) * TC 190 Soil quality
14 Beijing (China) * TC 23/SC 6 Tractors and machin-ery for agriculture and forestry/Equipment for crop protection
17-21 Stockholm (Sweden)
** TC 165 Timber structures
18-20 Berlin (Germany) * TC 122 Packaging
19-20 Rio de Janeiro (Brazil)
* TC 67 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries
ISO Update, Supplement to ISO Focus -- March 2012 19
19-21 San Diego (USA) ** GA General Assembly
22 San Diego (USA) ** COUNCIL Council
23-26 Rio de Janeiro (Brazil)
** TC 164/SC 3 Mechanical testing of metals/Hardness testing
24-25 Ottawa (Canada) * TAG 8 Building
24-25 Rio de Janeiro (Brazil)
** TC 164/SC 4 Mechanical testing of metals/Toughness testing -- Fracture (F), Pendulum (P), Tear (T)
24-26 Sydney (Australia)
* TC 54 Essential oils
24-28 Stockholm (Sweden)
** JTC 1/SC 38 Information tech-nology/Distributed application platforms and services (DAPS)
24-28 Vienna (Austria) ** TC 215 Health informatics
25-26 Rio de Janeiro (Brazil)
** TC 164/SC 2 Mechanical testing of metals/Ductility testing
25-27 Rio de Janeiro (Brazil)
** TC 164/SC 5 Mechanical testing of metals/Fatigue testing
27 Rio de Janeiro (Brazil)
** TC 164/SC 1 Mechanical testing of metals/Uniaxial testing
28 Rio de Janeiro (Brazil)
** TC 164 Mechanical testing of metals
Milan (Italy) ** TC 21/SC 3 Equipment for fire protection and fire fighting/Fire detection and alarm systems
Milan (Italy) ** TC 21/SC 6 Equipment for fire protection and fire fighting/Foam and powder media and firefighting systems using foam and powder
Milan (Italy) ** TC 21/SC 8 Equipment for fire protection and fire fighting/Gaseous media and firefighting systems using gas
(Korea, Repub-lic of)
** TC 133 Sizing systems and designations for clothes
Cadiz (Spain) ** TC 213 Dimensional and geometrical product specifications and verification
Rotorua (New Zealand)
** TC 218 Timber
September-October 2012
30-6 Paris (France) TC 106 Dentistry
3rd Quarter 2012
Frankfurt (Germany)
** TC 184/SC 1 Automation systems and integration/Physi-cal device control
Berlin (Germany) ** TC 254 Safety of amusement rides and amusement devices
October 2012
1-2 Ottawa (Canada) * TC 34/SC 11 Food products/Animal and vegetable fats and oils
3 Ottawa (Canada) * TC 34/SC 2 Food products/Ole-aginous seeds and fruits and oilseed meals
4-5 Montana-Verma-la (Switzerland)
TC 226 Materials for the production of primary aluminium
5 Berlin (Germany) * TC 79/SC 2 Light metals and their alloys/Or-ganic and anodic oxidation coatings on aluminium
6 Chicago (USA) * TC 130 Graphic technology
8-12 (USA) ** TC 154 Processes, data elements and documents in com-merce, industry and administration
9-10 Montreal (Canada)
* TC 199 Safety of machinery
10-11 Berlin (Germany) * TC 167 Steel and aluminium structures
10-12 Munich (Germany)
* TC 172/SC 6 Optics and photonics/Geodetic and survey-ing instruments
11-12 Bogota (Colombia)
* CASCO Committee on con-formity assessment
11-12 Tokyo (Japan) * TC 119 Powder metallurgy
14-18 Tokyo (Japan) ** TC 10/SC 8 Technical prod-uct documenta-tion/Construction documentation
14-19 Tokyo (Japan) TC 59 Buildings and civil engineering works
14-19 Praia do Forte (Brazil)
TC 127 Earth-moving machinery
15 Sydney (Australia)
TC 2/SC 7 Fasteners/Reference standards
15-19 Montreal (Canada)
* TC 6 Paper, board and pulps
15-19 Riccione (Italy) * TC 45 Rubber and rubber products
15-19 Riccione (Italy) * TC 45/SC 1 Rubber and rubber products/Hoses (rub-ber and plastics)
15-19 Riccione (Italy) ** TC 45/SC 4 Rubber and rubber products/Products (other than hoses)
15-19 Amsterdam (Netherlands)
* TC 146 Air quality
16 Sydney (Australia)
TC 2/SC 11 Fasteners/Fasteners with metric external thread
17 Sydney (Australia)
TC 2/SC 14 Fasteners/Surface coatings
17 (Korea, Repub-lic of)
** TC 17/SC 7 Steel/Methods of testing (other than mechanical tests and chemical analysis)
17 Berlin (Germany) * TC 22/SC 9 Road vehicles/Vehicle dynamics and road-holding ability
17-19 Guilin (China) * TC 202 Microbeam analysis
18 Sydney (Australia)
TC 2/SC 12 Fasteners/Fasteners with metric internal thread
18 Riccione (Italy) * TC 45/SC 2 Rubber and rubber products/Testing and analysis
20 ISO Update, Supplement to ISO Focus -- March 2012
18 Berlin (Germany) ** TC 83 Sports and recrea-tional equipment
18-19 (Korea, Repub-lic of)
** TC 17 Steel
19 Sydney (Australia)
TC 2 Fasteners
19 Riccione (Italy) * TC 45/SC 3 Rubber and rubber products/Raw materi-als (including latex) for use in the rubber industry
21-26 Sapporo (Japan) * TC 92 Fire safety
21-26 Sapporo (Japan) * TC 92/SC 1 Fire safety/Fire initia-tion and growth
21-26 Sapporo (Japan) ** TC 92/SC 2 Fire safety/Fire containment
22-26 (Japan) ** TC 181 Safety of toys
22-27 Jeju (Korea, Republic of)
TC 94/SC 15 Personal safety -- Protective clothing and equipment/Respiratory protective devices
23 Sydney (Australia)
** TC 138/SC 1 Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for soil, waste and drainage (includ-ing land drainage)
24 Sydney (Australia)
** TC 138/SC 2 Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for water supplies
24 Sydney (Australia)
** TC 138/SC 4 Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for the supply of gaseous fuels
25 Sydney (Australia)
** TC 138/SC 3 Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for industrial applications
25 Sydney (Australia)
** TC 138/SC 5 Plastics pipes, fittings and valves for the transport of fluids/General properties of pipes, fittings and valves of plastic materials and their accessories -- Test methods and basic specifications
25 Sydney (Australia)
** TC 138/SC 6 Plastics pipes, fittings and valves for the transport of fluids/Reinforced plastics pipes and fittings for all applications
25 Sydney (Australia)
** TC 138/SC 7 Plastics pipes, fittings and valves for the transport of fluids/Valves and auxiliary equipment of plastics materials
25-26 Tampa, Florida (USA)
** TC 112 Vacuum technology
25-27 Florida (USA) ** TC 201 Surface chemical analysis
26 Sydney (Australia)
** TC 138 Plastics pipes, fittings and valves for the transport of fluids
Messina (Italy) ** TC 8 Ships and marine technology
(USA) ** TC 36 Cinematography
(France) ** TC 70/SC 7 Internal combustion engines/Tests for lubricating oil filters
Yokohama (Japan)
** TC 119/SC 3 Powder metallurgy/Sampling and testing methods for sintered metal materials (ex-cluding hardmetals)
October-November 2012
29-1 Saitama (Japan) TC 34/SC 17 Food products/Man-agement systems for food safety
31-7 Orlando (USA) * TC 23/SC 18 Tractors and machin-ery for agriculture and forestry/Irrigation and drainage equipment and systems
November 2012
5 Berlin (Germany) * TC 79/SC 2 Light metals and their alloys/Or-ganic and anodic oxidation coatings on aluminium
5-8 Warsaw (Poland) * TC 98 Bases for design of structures
5-10 Jeju (Korea, Republic of)
** JTC 1 Information technology
6-8 Tokyo (Japan) * TC 17/SC 1 Steel/Methods of de-termination of chemi-cal composition
6-8 Reykjavik (Iceland)
TC 234 Fisheries and aquaculture
12 (Japan) ** TC 244 Industrial furnaces and associated pro-cessing equipment
15-16 Xian (China) * TC 227 Springs
26-27 London (United Kingdom)
* TC 44/SC 8 Welding and allied processes/Equip-ment for gas welding, cutting and allied processes
26-30 Florianopolis (Brazil)
* TC 43 Acoustics
26-30 Florianopolis (Brazil)
* TC 43/SC 1 Acoustics/Noise
27-29 Washington, D.C (USA)
* TC 20 Aircraft and space vehicles
(Korea, Repub-lic of)
** TC 23/SC 7 Tractors and machin-ery for agriculture and forestry/Equipment for harvesting and conservation
Wiesbaden (Germany)
** TC 67/SC 3 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Drilling and comple-tion fluids, and well cements
ISO Update, Supplement to ISO Focus -- March 2012 21
(USA) ** TC 118/SC 6 Compressors and pneumatic tools, machines and equip-ment/Air compressors and compressed air systems
Kyoto (Japan) ** TC 159/SC 4 Ergonomics/Ergo-nomics of human-system interaction
(Mexico) ** TC 229 Nanotechnologies
4th Quarter 2012
(Saudi Arabia) ** TC 211 Geographic in-formation/Geomatics
Month unknown 2012
(Europe) ** JTC 1/SC 24 Information technol-ogy/Computer graph-ics, image processing and environmental data representation
(Europe) ** TC 146/SC 6 Air quality/Indoor air
January 2013
(Unknown) ** TC 34/SC 16 Food products/Hori-zontal methods for molecular biomarker analysis
February 2013
4-8 (Unknown) ** TC 58/SC 4 Gas cylinders/Opera-tional requirements for gas cylinders
February-March 2013
25-1 (South America) ** JTC 1/SC 35 Information technol-ogy/User interfaces
April 2013
10-11 Helsinki (Finland) ** TC 117 Fans
Paris (France) ** TC 29/SC 5 Small tools/Grinding wheels and abrasives
Shenzen (China) ** TC 130 Graphic technology
(USA) ** TC 178 Lifts, escalators and moving walks
May 2013
13-16 Chicago (USA) ** TC 195 Building construc-tion machinery and equipment
13-17 (Italy) ** TC 29 Small tools
13-17 (Italy) ** TC 29/SC 8 Small tools/Tools for pressing and moulding
13-17 Guangzhou (China)
* TC 68 Financial services
13-17 Guangzhou (China)
* TC 68/SC 2 Financial services/Financial Services, security
27-31 Shanghai (China) * TC 4 Rolling bearings
Ottawa (Canada) ** JTC 1/SC 38 Information tech-nology/Distributed application platforms and services (DAPS)
(China) ** TC 10 Technical product documentation
Paris (France) ** TC 46/SC 11 Information and doc-umentation/Archives/records management
(Unknown) ** TC 158 Analysis of gases
June 2013
Washington, D.C (USA)
** TC 67/SC 3 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Drilling and comple-tion fluids, and well cements
2nd Quarter 2013
(Canada) ** TC 34/SC 4 Food products/Cere-als and pulses
August 2013
26-30 (South America) ** JTC 1/SC 35 Information technol-ogy/User interfaces
September 2013
(Korea, Repub-lic of)
** TC 17/SC 16 Steel/Steels for the reinforcement and prestressing of concrete
(Unknown) ** TC 21 Equipment for fire protection and fire fighting
Victoria (Canada) ** TC 33 Refractories
(Korea, Repub-lic of)
** TC 123/SC 2 Plain bearings/Materi-als and lubricants, their properties, characteristics, test methods and testing conditions
(Korea, Repub-lic of)
** TC 123/SC 3 Plain bearings/Dimen-sions, tolerances and construction details
(Korea, Repub-lic of)
** TC 123/SC 5 Plain bearings/Quality analysis and assurance
(Korea, Repub-lic of)
** TC 123/SC 6 Plain bearings/Terms and common items
(Korea, Repub-lic of)
** TC 123/SC 7 Plain bearings/Spe-cial types of plain bearings
Tokyo (Japan) ** TC 142 Cleaning equipment for air and other gases
October 2013
7 Istanbul (Turkey) ** TC 38/SC 1 Textiles/Tests for coloured textiles and colorants
7-11 Istanbul (Turkey) ** TC 38 Textiles
8 Istanbul (Turkey) ** TC 38/SC 2 Textiles/Cleansing, finishing and water resistance tests
9 Istanbul (Turkey) ** TC 38/SC 23 Textiles/Fibres and yarns
10 Istanbul (Turkey) ** TC 38/SC 24 Textiles/Condition-ing atmospheres and physical tests for textile fabrics
11 Garching (Germany)
** TC 60 Gears
11 Garching (Germany)
** TC 60/SC 1 Gears/Nomenclature and wormgearing
11 Garching (Germany)
** TC 60/SC 2 Gears/Gear capacity calculation