ISO Update · ISO/CD 6658 Sensory analysis — Methodology — General ... ISO Update, Supplement...
Transcript of ISO Update · ISO/CD 6658 Sensory analysis — Methodology — General ... ISO Update, Supplement...
ISO Update Supplement to ISOfocus
May 2015
ISO Update, Supplement to ISO Focus -- May 2015 1
International Standards in process
An International Standard is the result of an agreement between the member bodies of ISO. A first important step towards an Interna-tional Standard takes the form of a committee draft (CD) - this is cir-culated for study within an ISO technical committee. When consensus has been reached within the technical committee, the document is sent to the Central Secretariat for processing as a draft International Standard (DIS). The DIS requires approval by at least 75 % of the member bodies casting a vote. A confirmation vote is subsequently carried out on a final draft International Standard (FDIS), the approval criteria remaining the same.
CD registered
Period from 01 April to 30 April 2015
These documents are currently under consideration in the technical committee.
They have been registred at the Central Secretariat.
TC 20 Aircraft and space vehicles
ISO/CD 18170 Aerospace — AC Induction Electric Motor Driven, Variable Delivery, Hydraulic Pumps — General Specifications
TC 21 Equipment for fire protection and fire fighting
ISO/CD 6182-4 Fire protection — Automatic sprinkler systems — Part 4: Requirements and test methods for quick-opening devices
ISO/CD 6182-8 Fire protection — Automatic sprinkler systems — Part 8: Requirements and test methods for pre-action dry alarm valves
TC 28 Petroleum products and related prod-ucts of synthetic or biological origin
ISO/CD 19970 Refrigerated hydrocarbon and non-petroleum based liquefied gaseous fuels — Metering of gas as fuel on LNG carriers in ports
TC 34 Food products
ISO/CD 6658 Sensory analysis — Methodology — General guidance
ISO/CD 8588 Sensory analysis — Methodology — "A" - "not A" test
ISO/CD 13301 Sensory analysis — Methodology — General guidance for measuring odour, flavour and taste detection thresholds by a three-alterna-tive forced-choice (3-AFC) procedure
ISO/CD 20613 Sensory Analysis --- Guidelines for application of sensory analysis in food quality control
ISO/CD 13484 Foodstuffs — General requirements for molecular biology analysis for detection and identification of destructive organisms in plants and derived products
ISO/DTS 22002-6
Prerequisite programmes on food safety — Part 6: Feed and animal food production
ISO/CD 19381-1
Sustainable and traceable cocoa — Part 1: Sustainability management system — Requirements
ISO/CD 19381-2
Sustainable and traceable cocoa — Part 2: Performance requirements
ISO/CD 19381-3
Sustainable and traceable cocoa — Part 3: Traceability — Requirements
TC 35 Paints and varnishes
ISO/CD 15110 Paints and varnishes — Artificial weathering including acidic deposition
TC 61 Plastics
ISO/CD 5659-2 Plastics — Smoke generation — Part 2: Deter-mination of optical density by a single-chamber test
ISO 2797:1986/CD Amd 1
Textile glass — Rovings — Basis for a specifi-cation — Amendment 1
ISO 3616:2001/CD Amd 1
Textile glass — Chopped-strand and continu-ous-filament mats — Determination of average thickness, thickness under load and recovery after compression — Amendment 1
ISO 5025:1997/CD Amd 1
Reinforcement products — Woven fabrics — Determination of width and length — Amend-ment 1
TC 82 Mining
ISO/CD 19224 Continuous surface miner (CSM) - Safety
TC 107 Metallic and other inorganic coatings
ISO/CD 9717 Metallic and other inorganic coatings — Phos-phate conversion coating of metals
TC 131 Fluid power systems
ISO/CD 6605 Hydraulic fluid power — Hoses and hose as-semblies — Test methods
TC 133 Clothing sizing systems - size designa-tion, size measurement methods and digital fittings
ISO/CD 5971 Size designation of clothes — Pantyhose
TC 138 Plastics pipes, fittings and valves for the transport of fluids
ISO/CD 11296-2
Plastics piping systems for renovation of un-derground non-pressure drainage and sewer-age networks — Part 2: Lining with continuous pipes
ISO/CD 11297-2
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure — Part 2: Lining with continu-ous pipes
TC 146 Air quality
ISO/CD 20435-1
Workplace Atmospheres — Part 1: Gas detec-tors — Performance requirements of detectors for toxic gases
ISO/CD 16000-36
Indoor air — Part 36: Test method for the re-duction rate of airborne bacteria by air purifiers using a test chamber
TC 158 Analysis of gases
ISO/CD 12963 Gas analysis — Comparison methods for the determination of the composition of gas mix-tures based on one- and two-point calibration
TC 159 Ergonomics
ISO/CD 9241-306
Ergonomics of human-system interaction — Part 306: Field assessment methods for electronic visual displays
2 ISO Update, Supplement to ISO Focus -- May 2015
TC 172 Optics and photonics
ISO/CD 20711 Optics and optical instruments — Environmen-tal requirements
TC 178 Lifts, escalators and moving walks
ISO/CD 22201-1
Lifts (elevators), escalators and moving walks - Programmable electronic systems in safety related applications — Part 1: Lifts (elevators) (PESSRAL)
ISO/CD 22201-2
Lifts (elevators), escalators and moving walks — Programmable electronic systems in safety related applications — Part 2: Escalators and moving walks (PESSRAE)
ISO/DTR 22201-3
Lifts (elevators), escalators and moving walks — Programmable electronic systems in safety related applications — Part 3: Life cycle guideline for programmable electronic systems related to PESSRAL and PESSRAE
TC 204 Intelligent transport systems
ISO/DTS 21219-1
Intelligent transport systems — Traffic and Travel Information via Transport Protocol Experts Group, generation 2 (TPEG2) — Part 1: Introduction, numbering and versions (TPEG2-INV)
ISO/DTS 21219-9
Intelligent transport systems — Traffic and travel information (TTI) via transport protocol experts group, generation 2 (TPEG2) — Part 9: Service and network information (TPEG2-SNI)
ISO/DTS 21219-10
Intelligent transport systems — Traffic and trav-el information (TTI) via transport protocol ex-perts group, generation 2 (TPEG2) — Part 10: Conditional access information (TPEG2-CAI)
ISO/DTS 21219-19
Intelligent transport systems — Traffic and travel information (TTI) via Transport protocol expert group, generation 2 (TPEG2) — Part 19: Weather information application (TPEG2-WEA)
TC 206 Fine ceramics
ISO/CD 17168-1
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment — Part 1: Removal of nitric oxide
ISO/CD 17168-2
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconduct-ing photocatalytic materials under indoor lighting environment — Part 2: Removal of acetaldehyde
ISO/CD 17168-3
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment — Part 3: Removal of toluene
ISO/CD 17168-4
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconduct-ing photocatalytic materials under indoor lighting environment — Part 4: Removal of formaldehyde
ISO/CD 17168-5
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconducting photocatalytic materials under indoor lighting environment — Part 5: Removal of methyl mercaptan
ISO/CD 19722 Fine ceramics (advanced ceramics, advanced technical ceramics)- Test method for determi-nation of photocatalytic activity on semicon-ducting photocatalytic materials by dissolved oxygen consumption
ISO/CD 19810 Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for self-cleaning performance of semiconducting photocatalytic materials under indoor lighting environment — Measurement of water contact angle
ISO/CD 22197-1
Fine ceramics (advanced ceramics, advanced technical ceramics) — Test method for air-purification performance of semiconducting photocatalytic materials — Part 1: Removal of nitric oxide
JTC 1 Information technology
ISO/IEC 18031:2011/PDAM 1
Information technology — Security techniques — Random bit generation — Amendment 1: Test vectors for deterministic random bit generation
ISO/IEC CD 19823-11
Information technology — Conformance test methods for security service crypto suites — Part 11: Crypto suite PRESENT-80
ISO/IEC 9541-1:2012/PDAM 1
Information technology — Font information interchange — Part 1: Architecture — Amend-ment 1
DIS circulated
Period from 01 April to 30 April 2015
These documents have obtained substantial support within the ap-propriate ISO technical committee.
They have been submitted to the ISO member bodies for voting by the date shown.
* Available in English only
Vote terminates
TC 4 Rolling bearings
ISO/DIS 15242-1
* Rolling bearings — Measuring methods for vibration — Part 1: Fundamentals
2015-07-07
(Revision of ISO 15242-1:2004)
ISO/DIS 15242-2
* Rolling bearings — Measuring methods for vibration — Part 2: Radial ball bearings with cylindri-cal bore and outside surface
2015-07-07
(Revision of ISO 15242-2:2004, ISO 15242-2:2004/Cor 1:2010)
TC 8 Ships and marine technology
ISO/DIS 18079-1
* Ships and marine technology — Servicing of inflatable life-saving appliances — Part 1: General
2015-07-07
ISO/DIS 18079-2
* Ships and marine technology — Servicing of inflatable life-saving appliances — Part 2: Inflatable life rafts
2015-07-07
ISO/DIS 18079-3
* Ships and marine technology — Servicing of inflatable life-saving appliances — Part 3: Inflatable lifejackets
2015-07-07
ISO Update, Supplement to ISO Focus -- May 2015 3
ISO/DIS 18079-4
* Ships and marine technology — Servicing of inflatable life-saving appliances — Part 4: Marine evacuation systems
2015-07-07
ISO/DIS 18079-5
* Ships and marine technology — Servicing of inflatable life-saving appliances — Part 5: Inflated rescue boats
2015-07-07
ISO/DIS 484-1 * Shipbuilding — Ship screw propellers — Manufacturing tol-erances — Part 1: Propellers of diameter greater than 2,50 m
2015-07-09
(Revision of ISO 484-1:1981)
ISO/DIS 22472 * Ships and marine technology — Guidelines for the operation and installation of voyage data recorders (VDR)
2015-07-26
(Revision of ISO 22472:2006)
TC 10 Technical product documentation
ISO/DIS 129-1 * Technical product documenta-tion (TPD) — Indication of di-mensions and tolerances — Part 1: General principles
2015-07-28
(Revision of ISO 129-1:2004)
TC 17 Steel
ISO/DIS 18203.2
* Steel — Determination of the thickness of surface-hardened layers
(Revision of ISO 3754:1976, ISO 4970:1979, ISO 2639:2002)
TC 22 Road vehicles
ISO/DIS 6624-1
* Internal combustion engines — Piston rings — Part 1: Keystone rings made of cast iron
2015-07-18
(Revision of ISO 6624-1:2001)
ISO/DIS 6624-3
* Internal combustion engines — Piston rings — Part 3: Keystone rings made of steel
2015-07-18
(Revision of ISO 6624-3:2001)
ISO/DIS 6626-3
* Internal combustion engines — Piston rings — Part 3: Coil-spring-loaded oil control rings made of steel
2015-07-18
(Revision of ISO 6626-3:2008)
ISO/DIS 17488 * Road vehicles — Transport infor-mation and control systems — Detection-Response Task (DRT) for assessing attentional effects of cognitive load in driving
2015-07-07
TC 23 Tractors and machinery for agriculture and forestry
ISO/DIS 4254-5
* Agricultural machinery — Safety — Part 5: Power-driven soil-working machines
2015-07-24
(Revision of ISO 4254-5:2008)
ISO/DIS 4254-8
* Agricultural machinery — Safety — Part 8: Solid fertilizer distributors
2015-07-24
(Revision of ISO 4254-8:2009)
ISO/DIS 4254-9
* Agricultural machinery — Safety — Part 9: Seed drills
2015-07-24
(Revision of ISO 4254-9:2008)
ISO 21628:2008/DAmd 1
* Gardening machinery — Pow-ered material-collecting systems — Safety — Amendment 1
2015-07-25
TC 28 Petroleum products and re-lated products of synthetic or biological origin
ISO/DIS 15380 * Lubricants, industrial oils and related products (class L) — Family H (Hydraulic systems) — Specifications for hydraulic fluids in categories HETG, HEPG, HEES and HEPR
2015-07-04
(Revision of ISO 15380:2011)
TC 34 Food products
ISO 27608:2010/DAmd 1
* Animal and vegetable fats and oils — Determination of Lovibond® colour — Automatic method — Amendment 1
2015-07-08
TC 35 Paints and varnishes
ISO/DIS 19399 * Paints and varnishes — Wedge-cut method for determination of film thickness (scribe and drill method)
2015-07-24
TC 44 Welding and allied processes
ISO/DIS 18276 * Welding consumables — Tubular cored electrodes for gas-shield-ed and non-gasshielded metal arc welding of highstrength steels — Classification
2015-07-10
(Revision of ISO 18276:2005)
ISO/DIS 17916.2
* Safety of thermal cutting machines
TC 45 Rubber and rubber products
ISO/DIS 6134 * Rubber hoses and hose as-semblies for saturated steam — Specification
2015-07-03
(Revision of ISO 6134:2005)
ISO/DIS 6803 * Rubber or plastics hoses and hose assemblies — Hydraulic-pressure impulse test without flexing
2015-07-17
(Revision of ISO 6803:2008)
ISO/DIS 1421 * Rubber- or plastics-coated fab-rics — Determination of tensile strength and elongation at break
2015-07-10
(Revision of ISO 1421:1998)
ISO/DIS 4674-1
* Rubber- or plastics-coated fabrics — Determination of tear resistance — Part 1: Constant rate of tear methods
2015-07-03
(Revision of ISO 4674-1:2003)
ISO/DIS 5470-1
* Rubber- or plastics-coated fabrics — Determination of abra-sion resistance — Part 1: Taber abrader
2015-07-03
(Revision of ISO 5470-1:1999)
TC 68 Financial services
ISO/DIS 12812-1
* Core Banking — Mobile Finan-cial Services — Part 1: General framework
2015-07-09
ISO/DIS 12812-2
* Core banking — Mobile Financial Services — Part 2: Security and data protection for mobile finan-cial services
2015-07-09
4 ISO Update, Supplement to ISO Focus -- May 2015
ISO/DIS 12812-3
* Core Banking — Mobile Financial Services — Part 3: Financial application lifecycle management
2015-07-09
ISO/DIS 12812-4
* Core Banking — Mobile Finan-cial Services — Part 4: Mobile payments-to-person
2015-07-09
ISO/DIS 12812-5
* Core Banking — Mobile Finan-cial Services — Part 5: Mobile Payments to Business
2015-07-09
TC 76 Transfusion, infusion and injection, and blood processing equipment for medical and pharmaceuti-cal use
ISO/DIS 11040-8
* Prefilled syringes — Part 8: Re-quirements and test methods for finished prefilled syringes
2015-07-25
TC 89 Wood-based panels
ISO/DIS 16895.2
* Wood-based panels — Dry-process fibreboard
2015-06-18
(Revision of ISO 16895-1:2008, ISO 16895-2:2010)
ISO/DIS 16893.2
* Wood-based panels — Particleboard
2015-06-22
(Revision of ISO 16893-1:2008, ISO 16893-2:2010)
TC 94 Personal safety -- Pro-tective clothing and equipment
ISO/DIS 374-1 * Protective gloves against dan-gerous chemicals and micro-organisms — Part 1: Terminology and performance requirements for chemical risks
2015-07-24
ISO/DIS 374-5 * Protective gloves against dan-gerous chemicals and micro-organisms — Part 5: Terminology and performance requirements for micro-organisms risks
2015-07-24
TC 106 Dentistry
ISO/DIS 1797 * Dentistry — Shanks for rotary, oscillating and reciprocating instruments
2015-07-24
(Revision of ISO 1797-2:1992, ISO 1797-1:2011, ISO 1797-3:2013)
ISO/DIS 7787-1
* Dentistry — Laboratory cut-ters — Part 1: Steel laboratory cutters
2015-07-17
(Revision of ISO 7787-1:1984)
TC 108 Mechanical vibration, shock and condition monitoring
ISO 8041:2005/DAmd 1
* Human response to vibration — Measuring instrumentation — Amendment 1
2015-07-03
ISO/DIS 13374-4
* Condition monitoring and diagnostics of machine systems — Data processing, communica-tion and presentation — Part 4: Presentation
2015-07-25
TC 121 Anaesthetic and respiratory equipment
ISO/DIS 80601-2-74
* Medical Electrical Equipment — Part 2-74: Particular require-ments for basic safety and essential performance of respira-tory humidifying equipment
2015-07-14
TC 127 Earth-moving machinery
ISO 12117-2:2008/DAmd 1
* Earth-moving machinery — Lab-oratory tests and performance requirements for protective structures of excavators — Part 2: Roll-over protective structures (ROPS) for excavators of over 6 t — Amendment 1
2015-07-24
ISO/DIS 14990-1
* Earth-moving machinery — Elec-trical safety of machines utilising electric drives and related com-ponents and systems — Part 1: General Requirements
2015-07-16
ISO/DIS 14990-2
* Earth-moving machinery — Electrical safety of machines ut ilising electric drives and related components and systems — Part 2: Particular requirements for externally-powered machines
2015-07-16
ISO/DIS 14990-3
* Earth-moving machinery — Electrical safety of machines ut ilising electric drives and related components and systems — Part 3: Particular requirements for self-powered machines
2015-07-16
TC 130 Graphic technology
ISO/DIS 12632 * Graphic technology — Ink, paper and labels — Requirements on hot alkali penetration and resistance
2015-07-14
ISO 12647-6:2012/DAmd 1
* Graphic technology — Process control for the production of half-tone colour separations, proofs and production prints — Part 6: Flexographic printing — Amend-ment 1
2015-07-07
TC 133 Clothing sizing systems - size designation, size measurement methods and digital fittings
ISO/DIS 18825-2
* Clothing — Digital fittings — Part 2: Vocabulary and terminology used for attributes of the virtual human body
2015-07-24
TC 150 Implants for surgery
ISO/DIS 18242 * Cardiovascular implants and extracorporeal systems — Cen-trifugal blood pumps
2015-07-28
ISO/DIS 25539-1
* Cardiovascular implants — Endovascular devices — Part 1: Endovascular prostheses
(Revision of ISO 25539-1:2003, ISO 25539-1:2003/Amd 1:2005)
TC 163 Thermal performance and energy use in the built environment
ISO Update, Supplement to ISO Focus -- May 2015 5
ISO/DIS 14683 * Thermal bridges in building construction — Linear thermal transmittance — Simplified methods and default values
(Revision of ISO 14683:2007)
TC 164 Mechanical testing of metals
ISO/DIS 4545-1
* Metallic materials — Knoop hardness test — Part 1: Test method
2015-07-24
(Revision of ISO 4545-1:2005)
ISO/DIS 4545-2
* Metallic materials — Knoop hardness test — Part 2: Verifica-tion and calibration of testing machines
2015-07-24
(Revision of ISO 4545-2:2005)
ISO/DIS 4545-3
* Metallic materials — Knoop hardness test — Part 3: Calibra-tion of reference blocks
2015-07-24
(Revision of ISO 4545-3:2005)
ISO/DIS 4545-4
* Metallic materials — Knoop hardness test — Part 4: Table of hardness values
2015-07-24
(Revision of ISO 4545-4:2005)
ISO/DIS 14577-4
* Metallic materials — Instrument-ed indentation test for hardness and materials parameters — Part 4: Test method for metallic and non-metallic coatings
2015-07-24
(Revision of ISO 14577-4:2007)
TC 172 Optics and photonics
ISO/DIS 9022-9
* Optics and photonics — Envi-ronmental test methods — Part 9: Solar radiation and weathering
2015-07-24
(Revision of ISO 9022-9:1994)
ISO/DIS 10110-9
* Optics and photonics — Prepa-ration of drawings for optical elements and systems — Part 9: Surface treatment and coating
2015-07-24
(Revision of ISO 10110-9:1996)
TC 173 Assistive products for per-sons with disability
ISO/DIS 19026 * Accessible design — Shape and colour of a flushing button and a call button, and their arrange-ment with a paper dispenser installed on the wall in public restroom
2015-07-11
ISO/DIS 19029 * Accessible design — Auditory guiding signals in public facilities
2015-07-14
TC 188 Small craft
ISO/DIS 16315.4
* Small craft — Electric propulsion system
2015-06-03
TC 213 Dimensional and geometri-cal product specifications and verification
ISO/DIS 25178-72
* Geometrical product specifica-tions (GPS) — Surface texture: Areal — Part 72: XML file format x3p
2015-07-24
TC 238 Solid biofuels
ISO/DIS 18846 * Solid biofuels — Determination of fines content in quantities of pellets
2015-07-17
TC 244 Industrial furnaces and associated processing equipment
ISO/DIS 13577-1
* Industrial furnaces and associ-ated processing equipment — Safety — Part 1: General requirements
2015-07-24
(Revision of ISO 13577-1:2012)
TC 257 Evaluation of energy savings
ISO/DIS 17741.2
* General technical rules for measurement, calculation and verification of energy savings of projects
2015-06-11
TC 260 Human resource management
ISO/DIS 30405 * Human resource management — Guidelines on recruitment
2015-07-21
TC 268 Sustainable development in communities
ISO/DIS 37101 * Sustainable development of communities — Management systems — Requirements with guidance for resilience and smartness
2015-07-10
JTC 1 Information technology
ISO/IEC DIS 30191
* Information technology — Digitally recorded media for information interchange and storage — 120 mm Triple Layer (100,0 Gbytes single side disk and 200,0 Gbytes double sided disk) and Quadruple Layer (128,0 Gbytes single sided disk) BD Recordable disk
2015-07-24
(Revision of ISO/IEC 30191:2013)
ISO/IEC DIS 27010
* Information technology — Se-curity techniques — Information security management for inter-sector and inter-organizational communications
2015-07-25
(Revision of ISO/IEC 27010:2012)
ISO/IEC DIS 27033-6
* Information technology — Secu-rity techniques — Network secu-rity — Part 6: Securing wireless IP network access
2015-07-11
ISO/IEC 13818-1/DAmd 5
* Information technology — Ge-neric coding of moving pic-tures and associated audio information — Part 1: Systems — Amendment 5: New Profiles and Levels for MPEG-4 Audio Descriptor
2015-07-24
ISO/IEC DIS 15416
* Automatic identification and data capture techniques — Bar code print quality test specification — Linear symbols
2015-07-14
(Revision of ISO/IEC 15416:2000)
ISO/IEC DIS 13249-3
* Information technology — Da-tabase languages — SQL multi-media and application packages — Part 3: Spatial
2015-07-25
6 ISO Update, Supplement to ISO Focus -- May 2015
(Revision of ISO/IEC 13249-3:2011)
ISO/IEC DIS 30107-1
* Information Technology — Biometrics presentation attack detection — Part 1: Framework
2015-07-12
FDIS circulated
Period from 01 April to 30 April 2015
These Final draft International Standards have been submitted to the ISO member bodies for formal approval by the date shown
* Available in English only
Vote terminates
TC 8 Ships and marine technology
ISO/FDIS 6218 * Inland navigation vessels — Manually- and power-operated coupling devices for pushing units and coupled vessels — Safety requirements and main dimensions
2015-06-03
(Revision of ISO 6218:2005)
TC 17 Steel
ISO/FDIS 19272
* Low alloyed steel — Determina-tion of C, Si, Mn, P, S, Cr, Ni, Ai, Ti and Cu - Glow discharge optical emission spectrometry (routine method)
ISO/FDIS 643 * Steel — Micrographic determina-tion of the apparent grain size
2015-06-03
(Revision of ISO 643:2012)
ISO/FDIS 4990 * Steel castings — General techni-cal delivery requirements
2015-06-03
(Revision of ISO 4990:2003)
ISO/FDIS 4991 * Steel castings for pressure purposes
2015-06-03
(Revision of ISO 4991:2005)
ISO/FDIS 4993 * Steel and iron castings — Radio-graphic inspection
2015-06-03
(Revision of ISO 4993:2009)
ISO/FDIS 9477 * High strength cast steels for general engineering and struc-tural purposes
2015-06-03
(Revision of ISO 9477:1992)
ISO/FDIS 11970
* Specification and approval of welding procedures for produc-tion welding of steel castings
2015-06-03
(Revision of ISO 11970:2001)
ISO/FDIS 11972
* Corrosion-resistant cast steels for general applications
2015-06-03
(Revision of ISO 11972:1998)
ISO/FDIS 11973
* Heat-resistant cast steels and alloys for general applications
2015-06-03
(Revision of ISO 11973:1999)
ISO/FDIS 13520
* Determination of ferrite content in austenitic stainless steel castings
2015-06-03
(Revision of ISO 13520:2002)
ISO/FDIS 13521
* Austenitic manganese steel castings
2015-06-03
(Revision of ISO 13521:1999)
ISO/FDIS 13583-1
* Centrifugally cast steel and alloy products — Part 1: General test-ing and tolerances
2015-06-03
(Revision of ISO 13583-1:2000)
ISO/FDIS 13583-2
* Centrifugally cast steel and alloy products — Part 2: Heat resistant materials
2015-06-03
(Revision of ISO 13583-2:2003)
ISO/FDIS 14737
* Cast non-alloy and low alloy steels for general applications
2015-06-03
(Revision of ISO 3755:1991, ISO 14737:2003)
ISO/FDIS 16468
* Investment castings (steel, nickel alloys and cobalt alloys) — Gen-eral technical requirements
2015-06-03
(Revision of ISO 16468:2005)
ISO/FDIS 19960
* Cast steels and alloys with spe-cial physical properties
2015-06-03
(Revision of ISO 19960:2005)
TC 34 Food products
ISO/FDIS 17604
* Microbiology of the food chain — Carcass sampling for micro-biological analysis
2015-06-10
(Revision of ISO 17604:2003, ISO 17604:2003/Amd 1:2009)
ISO/FDIS 18743
* Microbiology of the food chain — Detection of Trichinella Larvae in meat by artificial digestion method
2015-06-24
ISO/FDIS 16779
* Sensory analysis — Assessment (determination and verification) of the shelf life of foodstuffs
2015-06-10
TC 35 Paints and varnishes
ISO/FDIS 8623 * Tall-oil fatty acids for paints and varnishes — Test methods and characteristic values
(Revision of ISO 8623:1997)
TC 44 Welding and allied processes
ISO/FDIS 14172
* Welding consumables — Cov-ered electrodes for manual metal arc welding of nickel and nickel alloys — Classification
2015-06-10
ISO Update, Supplement to ISO Focus -- May 2015 7
(Revision of ISO 14172:2008)
TC 45 Rubber and rubber products
ISO/FDIS 4665 * Rubber, vulcanized or ther-moplastic — Resistance to weathering
2015-06-25
(Revision of ISO 4665:2006)
TC 58 Gas cylinders
ISO/FDIS 11118
* Gas cylinders — Non-refillable metallic gas cylinders — Specifi-cation and test methods
2015-06-18
(Revision of ISO 11118:1999)
TC 61 Plastics
ISO/FDIS 11357-7
* Plastics — Differential scanning calorimetry (DSC) — Part 7: Determination of crystallization kinetics
(Revision of ISO 11357-7:2002)
ISO/FDIS 16616
* Test methods for Natural Fiber-reinforced Plastic Composite (NFC) Deck Boards
TC 67 Materials, equipment and offshore structures for pe-troleum, petrochemical and natural gas industries
ISO/FDIS 15156-1
* Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 1: General principles for selection of cracking-resistant materials
2015-06-24
(Revision of ISO 15156-1:2009)
ISO/FDIS 15156-2
* Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 2: Cracking-resistant carbon and low-alloy steels, and the use of cast irons
2015-06-24
(Revision of ISO 15156-2:2009)
ISO/FDIS 15156-3
* Petroleum and natural gas industries — Materials for use in H2S-containing environments in oil and gas production — Part 3: Cracking-resistant CRAs (corrosion-resistant alloys) and other alloys
2015-06-24
(Revision of ISO 15156-3:2009)
ISO/FDIS 16904
* Petroleum and natural gas industries — Design and testing of LNG marine transfer arms for conventional onshore terminals
2015-06-24
ISO/FDIS 19901-1
* Petroleum and natural gas indus-tries — Specific requirements for offshore structures — Part 1: Metocean design and operating considerations
2015-06-17
(Revision of ISO 19901-1:2005)
TC 69 Applications of statistical methods
ISO/FDIS 13528
* Statistical methods for use in proficiency testing by interlabo-ratory comparison
2015-06-21
(Revision of ISO 13528:2005)
TC 76 Transfusion, infusion and injection, and blood processing equipment for medical and pharmaceuti-cal use
ISO/FDIS 1135-4
* Transfusion equipment for medi-cal use — Part 4: Transfusion sets for single use, gravity feed
2015-06-24
(Revision of ISO 1135-4:2012)
ISO/FDIS 1135-5
* Transfusion equipment for medi-cal use — Part 5: Transfusion sets for single use with pressure infusion apparatus
2015-06-24
(Revision of ISO 1135:1977, ISO 1135-4:2012)
TC 106 Dentistry
ISO/FDIS 6874 * Dentistry — Polymer-based pit and fissure sealants
2015-06-10
(Revision of ISO 6874:2005)
ISO/FDIS 13397-5
* Dentistry — Periodontal curettes, dental scalers and excavators — Part 5: Jacquette scalers
2015-06-24
ISO/FDIS 16408
* Dentistry — Oral care products — Oral rinses
2015-06-10
(Revision of ISO 16408:2004)
TC 131 Fluid power systems
ISO/FDIS 19973-1
* Pneumatic fluid power — As-sessment of component reliabil-ity by testing — Part 1: General procedures
2015-06-30
(Revision of ISO 19973-1:2007)
TC 135 Non-destructive testing
ISO/FDIS 9934-1
* Non-destructive testing — Mag-netic particle testing — Part 1: General principles
2015-06-10
(Revision of ISO 9934-1:2001)
ISO/FDIS 9934-2
* Non-destructive testing — Mag-netic particle testing — Part 2: Detection media
2015-06-10
(Revision of ISO 9934-2:2002)
ISO/FDIS 9934-3
* Non-destructive testing — Mag-netic particle testing — Part 3: Equipment
2015-06-10
(Revision of ISO 9934-3:2002)
TC 138 Plastics pipes, fittings and valves for the transport of fluids
ISO/FDIS 17885
* Plastics piping systems — Mechanical fittings for pressure piping systems — Specifications
(Revision of ISO 10838-1:2000, ISO 10838-2:2000, ISO 14236:2000, ISO 10838-3:2001)
TC 146 Air quality
ISO/FDIS 16258-1
* Workplace air — Analysis of respirable crystalline silica by x-ray diffraction — Part 1: Direct on-filter method
2015-06-25
ISO/FDIS 16258-2
* Workplace air — Respirable crystalline silica by X-ray diffrac-tion — Part 2: Method by indirect analysis
2015-06-25
8 ISO Update, Supplement to ISO Focus -- May 2015
TC 150 Implants for surgery
ISO/FDIS 5840-1
* Cardiovascular implants — Car-diac valve prostheses — Part 1: General requirements
2015-06-10
ISO/FDIS 5840-2
* Cardiovascular implants — Car-diac valve prostheses — Part 2: Surgically implanted heart valve substitutes
2015-06-24
(Revision of ISO 5840:2005)
TC 164 Mechanical testing of metals
ISO/FDIS 16859-1
* Metallic materials — Leeb hard-ness test — Part 1: Test method
2015-06-10
ISO/FDIS 16859-2
* Metallic materials — Leeb hard-ness test — Part 2: Verification and calibration of the testing instruments
2015-06-10
ISO/FDIS 16859-3
* Metallic materials — Leeb hard-ness test — Part 3: Calibration of reference test blocks
2015-06-10
ISO/FDIS 14556
* Metallic materials — Charpy V-notch pendulum impact test — Instrumented test method
2015-06-03
(Revision of ISO 14556:2000, ISO 14556:2000/Amd 1:2006)
TC 173 Assistive products for per-sons with disability
ISO/FDIS 16840-6
* Wheelchair seating — Part 6: Simulated use and determination of the changes in properties — Seat cushions
2015-06-10
TC 188 Small craft
ISO/FDIS 12217-1
* Small craft — Stability and buoyancy assessment and cat-egorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m
2015-06-10
(Revision of ISO 12217-1:2002/Amd 1:2009, ISO 12217-1:2013)
ISO/FDIS 12217-2
* Small craft — Stability and buoy-ancy assessment and categori-zation — Part 2: Sailing boats of hull length greater than or equal to 6 m
2015-06-10
(Revision of ISO 12217-2:2013)
ISO/FDIS 12217-3
* Small craft — Stability and buoy-ancy assessment and catego-rization — Part 3: Boats of hull length less than 6 m
2015-06-10
(Revision of ISO 12217-3:2002/Amd 1:2009, ISO 12217-3:2013)
TC 189 Ceramic tile
ISO/FDIS 10545-14
* Ceramic tiles — Part 14: Deter-mination of resistance to stains
(Revision of ISO 10545-14:1995, ISO 10545-14:1995/Cor 1:1997)
TC 195 Building construction ma-chinery and equipment
ISO/FDIS 21873-1
* Building construction machinery and equipment — Mobile crush-ers — Part 1: Terminology and commercial specifications
(Revision of ISO 21873-1:2008)
TC 204 Intelligent transport systems
ISO/FDIS 24014-1
* Public transport — Interoperable fare management system — Part 1: Architecture
2015-06-10
(Revision of ISO 24014-1:2007)
TC 213 Dimensional and geometri-cal product specifications and verification
ISO/FDIS 14253-5
* Geometrical product specifica-tions (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 5: Uncertainty in testing indicating measuring instruments
2015-06-10
ISO/FDIS 16610-30
* Geometrical product specifica-tions (GPS) — Filtration — Part 30: Robust profile filters: Basic concepts
2015-06-18
(Revision of ISO/TS 16610-30:2009)
TC 249 Traditional chinese medicine
ISO/FDIS 18664
* Traditional Chinese Medicine — Determination of heavy metals in herbal medicines used in Traditional Chinese Medicine
2015-06-30
TC 256 Pigments, dyestuffs and extenders
ISO/FDIS 18473-1
* Functional pigments and extend-ers for special applications — Part 1: Nanoscale calcium carbonate for sealant application
ISO/FDIS 18473-2
* Functional pigments and extend-ers for special applications — Part 2: Nanoscale titanium dioxide for sunscreen application
JTC 1 Information technology
ISO/IEC FDIS 11889-1
* Information technology — Trust-ed Platform Module Library — Part 1: Architecture
2015-06-14
(Revision of ISO/IEC 11889-1:2009)
ISO/IEC FDIS 11889-2
* Information technology — Trust-ed Platform Module Library — Part 2: Structures
2015-06-14
(Revision of ISO/IEC 11889-2:2009)
ISO/IEC FDIS 11889-3
* Information technology — Trust-ed Platform Module Library — Part 3: Commands
2015-06-14
(Revision of ISO/IEC 11889-3:2009)
ISO/IEC FDIS 11889-4
* Information technology — Trust-ed Platform Module Library — Part 4: Supporting Routines
2015-06-14
(Revision of ISO/IEC 11889-4:2009)
ISO/IEC FDIS 19845
Information technology — Uni-versal Business Language Ver-sion 2.1 (UBL v2.1)
2015-06-23
ISO/IEC/IEEE FDIS 29119-4
* Software and systems engineer-ing — Software testing — Part 4: Test techniques
ISO Update, Supplement to ISO Focus -- May 2015 9
ISO/IEC FDIS 33063
* Information technology — Pro-cess assessment — Process assessment model for software testing
2015-06-23
ISO/IEC FDIS 14776-326
Information technology — Small Computer System Interface (SCSI) — Part 326: Reduced Block Commands (RBC)
2015-06-25
(Revision of ISO/IEC 14776-326:2002, ISO/IEC 14776-326:2002/Cor 1:2009)
ISO/IEC FDIS 27034-2
* Information technology — Se-curity techniques — Application security — Part 2: Organization normative framework
2015-06-25
ISO/IEC FDIS 29190.2
Information technology — Se-curity techniques — Privacy capability assessment model
ISO/IEC FDIS 28360
Information technology — Office equipment — Determination of chemical emission rates from electronic equipment
2015-06-18
(Revision of ISO/IEC 28360:2012)
ISO/IEC FDIS 15938-13
* Information technology — Mul-timedia content description interface — Part 13: Compact descriptors for visual search
2015-06-16
ISO/IEC FDIS 19785-1
* Information technology — Com-mon Biometric Exchange For-mats Framework — Part 1: Data element specification
2015-06-25
(Revision of ISO/IEC 19785-1:2006, ISO/IEC 19785-1:2006/Amd 1:2010)
Standards published
New International Standards published between 01 April and 30 April 2015
* Available in English only
** French version of standard previously published in English only
Price
group
REMCO Committee on reference materials
ISO/TR 79:2015
* Reference materials - Examples of reference materials for qualitative properties
F
TC 6 Paper, board and pulps
ISO 699:2015 * Pulps — Determination of alkali resistance
A
ISO 3260:2015 * Pulps — Determination of chlorine consumption (Degree of delignification)
A
TC 8 Ships and marine technology
ISO 18215:2015
* Ships and marine technology — Vessel machinery operations in polar waters — Guidelines
B
ISO 17683:2014
Ships and marine technology — Ce-ramic weld backing for marine use
A
TC 10 Technical product documentation
ISO 14084-2:2015
* Process diagrams for power plants — Part 2: Graphical symbols
G
TC 22 Road vehicles
ISO 27145-6:2015
* Road vehicles — Implementation of World-Wide Harmonized On-Board Diagnostics (WWH-OBD) communica-tion requirements — Part 6: External test equipment
E
ISO 10924-3:2015
* Road vehicles — Circuit breakers — Part 3: Miniature circuit breakers with tabs (Blade type), Form CB11
B
ISO 3537:2015 * Road vehicles — Safety glazing materi-als — Mechanical tests
D
ISO 16505:2015
* Road vehicles — Ergonomic and per-formance aspects of Camera Monitor Systems — Requirements and test procedures
H
TC 23 Tractors and machinery for agri-culture and forestry
ISO 8084:2003/Amd 1:2015
Machinery for forestry — Operator protective structures — Laboratory tests and performance requirements — Amendment 1
XZ
ISO 11783-7:2015
Tractors and machinery for agriculture and forestry — Serial control and com-munications data network — Part 7: Implement messages application layer
H
TC 24 Particle characterization includ-ing sieving
ISO 17867:2015
* Particle size analysis — Small-angle X-ray scattering
D
TC 27 Solid mineral fuels
ISO 602:2015 * Coal — Determination of mineral matter
B
TC 28 Petroleum products and related products of synthetic or biologi-cal origin
ISO 17786:2015
* Dimethyl ether (DME) for fuels — Determination of high temperature (105°C) evaporation residues — Mass analysis method
B
TC 29 Small tools
ISO 3317:2015 * Assembly tools for screws and nuts — Square drive adaptor with hexagon or cylindrical flat drive, for power socket wrenches
A
10 ISO Update, Supplement to ISO Focus -- May 2015
ISO 7738:2015 * Assembly tools for screws and nuts — Combination wrenches — Lengths of wrenches and maximum thickness of heads
A
TC 30 Measurement of fluid flow in closed conduits
ISO 10790:2015
* Measurement of fluid flow in closed conduits — Guidance to the selection, installation and use of Coriolis flowme-ters (mass flow, density and volume flow measurements)
F
TC 34 Food products
ISO 8455:2011/Amd 1:2015
* Green coffee — Guidelines for storage and transport — Amendment 1
XZ
TC 37 Terminology and other language and content resources
ISO 17100:2015
Translation services — Requirements for translation services
D
TC 38 Textiles
ISO 18066:2015
* Textiles — Manmade filament yarns — Determination of shrinkage in boiling water
B
TC 42 Photography
ISO 17957:2015
* Photography — Digital cameras — Shading measurements
C
TC 44 Welding and allied processes
ISO 11745:2010/Amd 1:2015
* Brazing for aerospace applications — Qualification test for brazers and braz-ing operators — Brazing of metallic components — Amendment 1
XZ
ISO 16237:2015
* Mechanical joining — Destructive test-ing of joints — Specimen dimensions and test procedure for cross-tension testing of single joints
B
ISO 18278-1:2015
Resistance welding — Weldability — Part 1: General requirements for the evaluation of weldability for resistance spot, seam and projection welding of metallic materials
B
ISO 2503:2009/Amd 1:2015
Gas welding equipment — Pressure regulators and pressure regulators with flow-metering devices for gas cylinders used in welding, cutting and allied processes up to 300 bar (30 MPa) — Amendment 1
XZ
ISO 5172:2006/Amd 2:2015
Gas welding equipment — Blowpipes for gas welding, heating and cutting — Specifications and tests — Amend-ment 2
XZ
ISO 7291:2010/Amd 1:2015
Gas welding equipment — Pressure regulators for manifold systems used in welding, cutting and allied processes up to 30 MPa (300 bar) — Amendment 1
XZ
TC 45 Rubber and rubber products
ISO 18517:2015
* Rubber, vulcanized or thermoplastic — Hardness testing — Introduction and guide
A
TC 61 Plastics
ISO 13927:2015
Plastics — Simple heat release test using a conical radiant heater and a thermopile detector
D
ISO 16620-1:2015
Plastics — Biobased content — Part 1: General principles
B
ISO 16620-2:2015
* Plastics — Biobased content — Part 2: Determination of biobased carbon content
D
ISO 16620-3:2015
* Plastics — Biobased content — Part 3: Determination of biobased synthetic polymer content
B
ISO 15106-5:2015
* Plastics — Film and sheeting — Deter-mination of water vapour transmission rate — Part 5: Pressure sensor method
B
ISO 15106-6:2015
* Plastics — Film and sheeting — Deter-mination of water vapour transmission rate — Part 6: Atmospheric pressure ionization mass spectrometer method
B
ISO 15106-7:2015
* Plastics — Film and sheeting — De-termination of water vapour transmis-sion rate — Part 7: Calcium corrosion method
B
TC 67 Materials, equipment and off-shore structures for petroleum, petrochemical and natural gas industries
ISO/TR 17177:2015
* Petroleum and natural gas industries — Guidelines for the marine interfaces of hybrid LNG terminals
E
ISO 17945:2015
* Petroleum, petrochemical and natural gas industries — Metallic materials re-sistant to sulfide stress cracking in cor-rosive petroleum refining environments
F
TC 70 Internal combustion engines
ISO 7967-12:2014
Reciprocating internal combustion engines — Vocabulary of components and systems — Part 12: Exhaust emis-sion control systems
B
TC 71 Concrete, reinforced concrete and pre-stressed concrete
ISO 18319:2015
* Fibre-reinforced polymer (FRP) rein-forcement for concrete structures — Specifications of FRP sheets
A
TC 76 Transfusion, infusion and injection, and blood process-ing equipment for medical and pharmaceutical use
ISO 11040-4:2015
Prefilled syringes — Part 4: Glass barrels for injectables and sterilized subassembled syringes ready for filling
G
ISO 11040-7:2015
Prefilled syringes — Part 7: Packaging systems for sterilized subassembled syringes ready for filling
E
TC 84 Devices for administration of medicinal products and catheters
ISO 10555-6:2015
Intravascular catheters — Sterile and single-use catheters — Part 6: Subcu-taneous implanted ports
C
ISO Update, Supplement to ISO Focus -- May 2015 11
TC 91 Surface active agents
ISO 16560:2015
* Surface active agents — Determination of polyethylene glycol content in non-ionic ethoxylated surfactants — HPLC method
B
TC 94 Personal safety -- Protective clothing and equipment
ISO/TS 16976-2:2015
* Respiratory protective devices — Hu-man factors — Part 2: Anthropometrics
D
TC 106 Dentistry
ISO 24234:2015
Dentistry — Dental amalgam
D
TC 108 Mechanical vibration, shock and condition monitoring
ISO 7626-2:2015
* Mechanical vibration and shock — Ex-perimental determination of mechani-cal mobility — Part 2: Measurements using single-point translation excitation with an attached vibration exciter
D
ISO 10816-21:2015
Mechanical vibration — Evaluation of machine vibration by measurements on non-rotating parts — Part 21: Horizon-tal axis wind turbines with gearbox
C
ISO 16063-16:2014
* Methods for the calibration of vibration and shock transducers — Part 16: Calibration by Earth's gravitation
B
ISO 13379-2:2015
* Condition monitoring and diagnostics of machines — Data interpretation and diagnostics techniques — Part 2: Data-driven applications
B
ISO 18129:2015
* Condition monitoring and diagnostics of machines — Approaches for perfor-mance diagnosis
C
TC 111 Round steel link chains, chain slings, components and accessories
ISO 16872:2015
Round steel short link chains for lift-ing purposes — Fine tolerance hoist chains for hand operated chain hoists — Grade VH
C
ISO 16877:2015
Round steel short link chains for lift-ing purposes — Fine tolerance hoist chains for hand operated chain hoists — Grade TH
C
TC 115 Pumps
ISO/ASME 14414:2015
Pump system energy assessment
G
TC 118 Compressors and pneumatic tools, machines and equipment
ISO 10439-1:2015
Petroleum, petrochemical and natural gas industries — Axial and centrifugal compressors and expander-compres-sors — Part 1: General requirements
H
ISO 10439-2:2015
Petroleum, petrochemical and natural gas industries — Axial and centrifugal compressors and expander-compres-sors — Part 2: Non-integrally geared centrifugal and axial compressors
G
ISO 10439-3:2015
Petroleum, petrochemical and natural gas industries — Axial and centrifugal compressors and expander-com-pressors — Part 3: Integrally geared centrifugal compressors
G
ISO 10439-4:2015
Petroleum, petrochemical and natural gas industries — Axial and centrifugal compressors and expander-compres-sors — Part 4: Expander-compressors
G
TC 119 Powder metallurgy
ISO 14317:2015
* Sintered metal materials excluding hardmetals — Determination of com-pressive yield strength
A
TC 121 Anaesthetic and respiratory equipment
ISO 18835:2015
* Inhalational anaesthesia systems — Draw-over anaesthetic systems
D
TC 130 Graphic technology
ISO 17972-1:2015
* Graphic technology — Colour data exchange format — Part 1: Relation-ship to CxF3 (CxF/X)
C
TC 131 Fluid power systems
ISO 10762:2015
* Hydraulic fluid power — Mounting dimensions for cylinders, 10 MPa (100 bar) series
D
TC 135 Non-destructive testing
ISO 16946:2015
Non-destructive testing — Ultrasonic testing — Specification for step wedge calibration block
A
ISO 18249:2015
* Non-destructive testing — Acoustic emission testing — Specific methodol-ogy and general evaluation criteria for testing of fibre-reinforced polymers
D
TC 137 Footwear sizing designations and marking systems
ISO/TS 19407:2015
Footwear — Sizing — Conversion of sizing systems
B
TC 147 Water quality
ISO 9697:2015 Water quality — Gross beta activity in non-saline water — Test method using thick source
B
TC 156 Corrosion of metals and alloys
ISO 17224:2015
Corrosion of metals and alloys — Test method for high temperature corrosion testing of metallic materials by applica-tion of a deposit of salt, ash, or other substances
C
ISO 17245:2015
Corrosion of metals and alloys — Test method for high temperature corrosion testing of metallic materials by immers-ing in molten salt or other liquids under static conditions
C
ISO 17248:2015
Corrosion of metals and alloys — Test method for high temperature corrosion testing of metallic materials by embed-ding in salt, ash, or other solids
C
TC 164 Mechanical testing of metals
12 ISO Update, Supplement to ISO Focus -- May 2015
ISO 6892-3:2015
Metallic materials — Tensile test-ing — Part 3: Method of test at low temperature
D
TC 172 Optics and photonics
ISO 9022-11:2015
* Optics and photonics — Environmental test methods — Part 11: Mould growth
B
ISO 8600-2:2015
* Endoscopes - Medical endoscopes and endotherapy devices — Part 2: Particular requirements for rigid bronchoscopes
C
ISO 19012-3:2015
* Microscopes — Designation of micro-scope objectives — Part 3: Spectral transmittance
A
ISO 16971:2015
Ophthalmic instruments — Optical coherence tomograph for the posterior segment of the human eye
B
ISO 19045:2015
* Ophthalmic optics — Contact lens care products — Method for evaluating Acanthamoeba encystment by contact lens care products
C
TC 174 Jewellery
ISO 11495:2014
Jewellery — Determination of pal-ladium in palladium jewellery alloys — ICP-OES method using yttrium as internal standard element
B
TC 188 Small craft
ISO 18854:2015
Small craft — Reciprocating internal combustion engines exhaust emission measurement — Test-bed measure-ment of gaseous and particulate exhaust emissions
H
TC 201 Surface chemical analysis
ISO 18118:2015
* Surface chemical analysis — Auger electron spectroscopy and X-ray photoelectron spectroscopy — Guide to the use of experimentally deter-mined relative sensitivity factors for the quantitative analysis of homogeneous materials
D
TC 204 Intelligent transport systems
ISO 13185-2:2015
* Intelligent transport systems — Vehicle interface for provisioning and sup-port of ITS services — Part 2: Unified gateway protocol (UGP) requirements and specification for vehicle ITS station gateway (V-ITS-SG) interface
G
ISO/TR 17424:2015
* Intelligent transport systems — Coop-erative systems — State of the art of Local Dynamic Maps concepts
E
ISO/TS 19321:2015
* Intelligent transport systems — Coop-erative ITS — Dictionary of in-vehicle information (IVI) data structures
F
ISO 26684:2015
* Intelligent transport systems (ITS) — Cooperative intersection signal infor-mation and violation warning systems (CIWS) — Performance requirements and test procedures
B
TC 205 Building environment design
ISO 11855-1:2012
Building environment design — Design, dimensioning, installation and control of embedded radiant heating and cooling systems — Part 1: Definition, symbols, and comfort criteria
E
TC 212 Clinical laboratory testing and in vitro diagnostic test systems
ISO/TS 17518:2015
* Medical laboratories — Reagents for staining biological material — Guid-ance for users
C
TC 213 Dimensional and geometrical product specifications and verification
ISO 16610-1:2015
Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts
D
ISO 16610-20:2015
Geometrical product specifications (GPS) — Filtration — Part 20: Linear profile filters: Basic concepts
C
ISO 16610-29:2015
Geometrical product specifications (GPS) — Filtration — Part 29: Linear profile filters: Spline wavelets
C
TC 215 Health informatics
ISO/TS 16277-1:2015
* Health informatics — Categorial struc-tures of clinical findings in traditional medicine — Part 1: Traditional Chinese, Japanese and Korean medicine
C
ISO 22077-1:2015
* Health informatics — Medical wave-form format — Part 1: Encod-ing rules
F
TC 238 Solid biofuels
ISO 16967:2015
Solid biofuels — Determination of major elements — Al, Ca, Fe, Mg, P, K, Si, Na and Ti
C
TC 254 Safety of amusement rides and amusement devices
ISO 17842-2:2015
* Safety of amusement rides and amuse-ment devices — Part 2: Operation and use
D
TC 256 Pigments, dyestuffs and extenders
ISO 23900-1:2015
* Pigments and extenders — Methods of dispersion and assessment of dispers-ibility in plastics — Part 1: General introduction
A
ISO 23900-2:2015
* Pigments and extenders — Methods of dispersion and assessment of dispers-ibility in plastics — Part 2: Determina-tion of colouristic properties and ease of dispersion in plasticized polyvinyl chloride by two-roll milling
B
ISO 23900-3:2015
* Pigments and extenders — Methods of dispersion and assessment of dispers-ibility in plastics — Part 3: Determi-nation of colouristic properties and ease of dispersion of black and colour pigments in polyethylene by two-roll milling
A
ISO 23900-4:2015
* Pigments and extenders — Methods of dispersion and assessment of dispers-ibility in plastics — Part 4: Determina-tion of colouristic properties and ease of dispersion of white pigments in polyethylene by two-roll milling
A
ISO 23900-5:2015
* Pigments and extenders — Methods of dispersion and assessment of dispers-ibility in plastics — Part 5: Determina-tion by filter pressure value test
B
ISO Update, Supplement to ISO Focus -- May 2015 13
ISO 23900-6:2015
* Pigments and extenders — Methods of dispersion and assessment of dispers-ibility in plastics — Part 6: Determina-tion by film test
B
IULTCS International Union of Leather Technologists and Chemists Societies
ISO 15701:2015
Leather — Tests for colour fastness — Colour fastness to migration into polymeric material
A
JTC 1 Information technology
ISO/IEC 2382:2015
* Information technology — Vocabulary
free
ISO/IEC 19678:2015
* Information Technology — BIOS Pro-tection Guidelines
C
ISO/IEC 19831:2015
* Cloud Infrastructure Management Interface (CIMI) Model and RESTful HTTP-based Protocol — An Interface for Managing Cloud Infrastructure
H
ISO/IEC/IEEE 8802-22:2015
* Information technology — Telecom-munications and information exchange between systems — Local and metropolitan area networks — Specific requirements — Part 22: Cognitive Wireless RAN Medium Access Control (MCA) and Physical Layer (PHY) Speci-fications: Policies and Procedures for Operation in the TV Bands
H
ISO/IEC/IEEE 8802-1AE:2013/Amd 1:2015
* Information technology — Telecom-munications and information exchange between systems — Local and met-ropolitan area networks — Part 1AE: Media access control (MAC) security — Amendment 1: Galois Counter Mode— — Advanced Encryption Standard-256 (GCM-AES-256) Cipher Suite
F
ISO/IEC/IEEE 8802-1AE:2013/Amd 2:2015
* Information technology — Telecom-munications and information exchange between systems — Local and met-ropolitan area networks — Part 1AE: Media access control (MAC) security — Amendment 2: Extended Packet Numbering
G
ISO/IEC 17821:2015
* Information technology — Specifica-tion of low power wireless mesh net-work over channel-hopped TDMA links
G
ISO/IEC/IEEE 18880:2015
* Information technology — Ubiquitous green community control network protocol
G
ISO/IEC TR 12182:2015
* Systems and software engineering — Framework for categorization of IT systems and software, and guide for applying it
D
ISO/IEC 15414:2015
* Information technology — Open distributed processing — Reference model — Enterprise language
F
ISO/IEC 14543-5-7:2015
* Information technology — Home electronic system (HES) architecture — Part 5-7: Intelligent Grouping and 3 Resource Sharing — Remote Access System Architecture
B
ISO/IEC 18014-4:2015
* Information technology — Security techniques — Time-stamping services — Part 4: Traceability of time sources
C
ISO/IEC 23002-4:2014/Amd 2:2015
* Information technology — MPEG video technologies — Part 4: Video tool library — Amendment 2: FU and FN descriptions for HEVC
D
ISO/IEC 23007-3:2011/Amd 1:2015
* Information technology — Rich media user interfaces — Part 3: Conformance and reference software — Amendment 1: Conformance and reference soft-ware for widget extension and AUI
XZ
ISO/IEC 23008-1:2014/Amd 1:2015
* Information technology — High ef-ficiency coding and media delivery in heterogeneous environments — Part 1: MPEG media transport (MMT) — Amendment 1: Additional technologies for MPEG Media Transport (MMT)
E
ISO/IEC 23008-5:2015
* Information technology — High ef-ficiency coding and media delivery in heterogeneous environments — Part 5: Reference software for high efficiency video coding
A
ISO/IEC 23008-8:2015
* Information technology — High ef-ficiency coding and media delivery in heterogeneous environments — Part 8: Conformance Specification for HEVC
F
ISO/IEC 23008-10:2015
* Information technology — High ef-ficiency coding and media delivery in heterogeneous environments — Part 10: MPEG Media Transport Forward Error Correction (FEC) codes
E
ISO/IEC TR 23009-3:2015
* Information technology — Dynamic adaptive streaming over HTTP (DASH) — Part 3: Implementation Guidelines
F
ISO/IEC 30113-1:2015
* Information technology — User interface — Gesture-based interfaces across devices and methods — Part 1: Framework
C
ISO/IEC 29120-1:2015
* Information technology — Machine readable test data for biometric testing and reporting — Part 1: Test reports
F
ISO/IEC TS 38501:2015
* Information technology — Governance of IT — Implementation guide
C
Standards confirmed
The following International Standards are confimred for a five year period:
TC 4 Rolling bearings
ISO 113:2010
ISO 5753-2:2010
TC 5 Ferrous metal pipes and metallic fittings
ISO 228-2:1987 (reconfirmed)
ISO 2016:1981 (reconfirmed)
ISO 4144:2003 (reconfirmed)
14 ISO Update, Supplement to ISO Focus -- May 2015
ISO 4145:1986 (reconfirmed)
ISO 5251:1981 (reconfirmed)
ISO 7369:2004 (reconfirmed)
ISO 10806:2003 (reconfirmed)
TC 17 Steel
ISO 9442:1988 (reconfirmed)
ISO 11692:1994 (reconfirmed)
TC 22 Road vehicles
ISO 9817:1991 (reconfirmed)
ISO 9818:1991 (reconfirmed)
TC 23 Tractors and machinery for agriculture and forestry
ISO/OECD 789-10:2006
(reconfirmed)
ISO 14269-2:1997 (reconfirmed)
ISO 19472:2006 (reconfirmed)
TC 29 Small tools
ISO 3936:1993 (reconfirmed)
ISO 5413:1993 (reconfirmed)
ISO 10889-1:2004 (reconfirmed)
ISO 10889-8:1997 (reconfirmed)
TC 31 Tyres, rims and valves
ISO 10231:2003 (reconfirmed)
TC 34 Food products
ISO/TS 22002-3:2011
TC 36 Cinematography
ISO 26428-9:2009
ISO 26429-8:2009
ISO 26430-5:2009
ISO 26430-6:2009
ISO 26430-9:2009
ISO 26433:2009
TC 37 Terminology and other language and content resources
ISO 23185:2009
TC 43 Acoustics
ISO 354:2003
TC 44 Welding and allied processes
ISO 10042:2005 (reconfirmed)
TC 46 Information and documentation
ISO 16245:2009
TC 61 Plastics
ISO 489:1999 (reconfirmed)
ISO 2555:1989 (reconfirmed)
ISO 3915:1981 (reconfirmed)
ISO 11359-1:2014
ISO 13468-2:1999 (reconfirmed)
ISO 14782:1999 (reconfirmed)
ISO 177:1988 (reconfirmed)
ISO 22088-1:2006 (reconfirmed)
ISO 22088-2:2006 (reconfirmed)
ISO 22088-3:2006 (reconfirmed)
ISO 22088-4:2006 (reconfirmed)
ISO 22088-5:2006 (reconfirmed)
ISO 22088-6:2006 (reconfirmed)
ISO 1888:2006 (reconfirmed)
ISO 3375:2009
ISO 14126:1999 (reconfirmed)
TC 83 Sports and other recreational facilities and equipment
ISO 8364:2007
TC 92 Fire safety
ISO 5657:1997 (reconfirmed)
ISO 16734:2006 (reconfirmed)
ISO 16736:2006 (reconfirmed)
TC 96 Cranes
ISO 8566-5:1992 (reconfirmed)
TC 106 Dentistry
ISO 3823-2:2003 (reconfirmed)
ISO 21531:2009
TC 114 Horology
ISO 17514:2004 (reconfirmed)
ISO 6426-1:1982 (reconfirmed)
ISO 6426-2:2002 (reconfirmed)
ISO 14368-2:2003 (reconfirmed)
TC 119 Powder metallurgy
ISO 3907:2009
ISO 3908:2009
ISO 28079:2009
TC 122 Packaging
ISO 8351-1:1994 (reconfirmed)
ISO 8351-2:1994 (reconfirmed)
ISO 11897:1999 (reconfirmed)
ISO 20848-1:2006 (reconfirmed)
ISO 20848-2:2006 (reconfirmed)
ISO 20848-3:2006 (reconfirmed)
TC 126 Tobacco and tobacco products
ISO 20369:2009
ISO 20370:2009
ISO 15152:2003 (reconfirmed)
ISO 15153:2003 (reconfirmed)
ISO 15154:2003 (reconfirmed)
ISO 15517:2003 (reconfirmed)
TC 146 Air quality
ISO 9096:2003 (reconfirmed)
ISO 12141:2002 (reconfirmed)
ISO 15713:2006 (reconfirmed)
ISO 23210:2009
TC 171 Document management applications
ISO 19005-1:2005 (reconfirmed)
ISO 24537:2007
TC 172 Optics and photonics
ISO 14134:2006 (reconfirmed)
ISO 14490-1:2005 (reconfirmed)
ISO 14490-2:2005 (reconfirmed)
ISO 14490-4:2005 (reconfirmed)
TC 178 Lifts, escalators and moving walks
ISO/TS 22559-3:2011
ISO/TS 25740-1:2011
ISO Update, Supplement to ISO Focus -- May 2015 15
TC 180 Solar energy
ISO 9845-1:1992 (reconfirmed)
TC 184 Automation systems and integration
ISO/TS 8000-1:2011
ISO/TS 15926-7:2011
ISO/TS 15926-8:2011
ISO 16100-1:2009
TC 205 Building environment design
ISO 16484-2:2004 (reconfirmed)
JTC 1 Information technology
ISO/IEC 14496-4:2004
(reconfirmed)
Standards withdrawn
Period from 01 April to 30 April 2015
TC 2 Fasteners
ISO 8839:1986 (replaced by )
TC 8 Ships and marine technology
ISO/PAS 18215:2012
(replaced by ISO 18215:2015)
ISO 6205:1988 (replaced by )
ISO 6219:1983 (replaced by )
TC 29 Small tools
ISO 2726:1995 (replaced by )
TC 34 Food products
ISO 27085:2009 (replaced by )
TC 44 Welding and allied processes
ISO 8166:2003 (replaced by )
TC 45 Rubber and rubber products
ISO 5478:2006 (replaced by )
ISO 4655:1985 (replaced by )
ISO 9252:1989 (replaced by )
TC 86 Refrigeration and air-conditioning
ISO 917:1989 (replaced by )
ISO 9309:1989 (replaced by )
TC 121 Anaesthetic and respiratory equipment
ISO/TS 18835:2004
(replaced by ISO 18835:2015)
TC 131 Fluid power systems
ISO 5784-1:1988 (replaced by )
ISO 5784-2:1989 (replaced by )
ISO 5784-3:1989 (replaced by )
TC 153 Valves
ISO 5996:1984 (replaced by )
ISO 7259:1988 (replaced by )
TC 164 Mechanical testing of metals
ISO 15579:2000 (replaced by ISO 6892-3:2015)
TC 188 Small craft
ISO 12402-1:2005 (replaced by )
TC 213 Dimensional and geometrical product specifications and verification
ISO/TS 16610-1:2006
(replaced by ISO 16610-1:2015)
ISO/TS 16610-20:2006
(replaced by ISO 16610-20:2015)
ISO/TS 16610-29:2006
(replaced by ISO 16610-29:2015)
JTC 1 Information technology
ISO/IEC 2382-1:1993
(replaced by ISO/IEC 2382:2015)
ISO 2382-2:1976 (replaced by ISO/IEC 2382:2015)
ISO 2382-3:1987 (replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-7:2000
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-8:1998
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-9:1995
(replaced by ISO/IEC 2382:2015)
ISO 2382-10:1979 (replaced by ISO/IEC 2382:2015)
ISO 2382-12:1988 (replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-13:1996
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-14:1997
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-15:1999
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-16:1996
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-18:1999
(replaced by ISO/IEC 2382:2015)
ISO 2382-19:1989 (replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-20:1990
(replaced by ISO/IEC 2382:2015)
ISO 2382-21:1985 (replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-23:1994
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-24:1995
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-25:1992
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-26:1993
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-27:1994
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-28:1995
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-29:1999
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-31:1997
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-32:1999
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-34:1999
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-4:1999
(replaced by ISO/IEC 2382:2015)
ISO/IEC 2382-5:1999
(replaced by ISO/IEC 2382:2015)
ISO 2382-6:1987 (replaced by ISO/IEC 2382:2015)
16 ISO Update, Supplement to ISO Focus -- May 2015
ISO/IEC 2382-17:1999
(replaced by ISO/IEC 2382:2015)
Meeting calendar
(update at 01 April 2015)
Meetings called for the month of March are not in this edition.
* Information definite but meeting not yet formally convened
** Provisional
May 2015
4 Toronto (Canada) TC 68/SC 4 Financial services/Securities and related financial instruments
4-7 Buxton (United Kingdom)
TC 94/SC 15 Personal safety -- Protective clothing and equipment/Respiratory protective devices
5 Toronto (Canada) TC 68/SC 7 Financial services/Core banking
6 Toronto (Canada) TC 68/SC 2 Financial services/Financial Services, security
7 Toronto (Canada) TC 68 Financial services
10-15 Rio de Janeiro (Brazil)
JTC 1/SC 7 Information technol-ogy/Software and systems engineering
11-12 Kuching (Malaysia)
JTC 1/SC 27 Information tech-nology/IT Security techniques
11-12 Ottawa (Canada) TC 159/SC 4 Ergonomics/Ergo-nomics of human-system interaction
11-15 Ohio (USA) TC 184/SC 5 Automation systems and integration/Inter-operability, integra-tion, and architec-tures for enterprise systems and automa-tion applications
11-16 Bologna (Italy) TC 130 Graphic technology
12-15 Beijing (China) TC 156 Corrosion of metals and alloys
12-15 Shanghai (China) TC 172/SC 7 Optics and photon-ics/Ophthalmic optics and instruments
13 Tokyo (Japan) TC 10/SC 6 Technical product documentation/Me-chanical engineering documentation
13 Turin (Italy) TC 22/SC 35 Road vehicles/Light-ing and visibility
13 Paris (France) TC 87 Cork
14 Tokyo (Japan) TC 10/SC 1 Technical product documentation/Basic conventions
15 Tokyo (Japan) TC 10 Technical product documentation
17-22 Copenhagen (Denmark)
TC 173/SC 1 Assistive products for persons with disability/Wheelchairs
18-22 Glasgow, Scotland (United Kingdom)
JTC 1/SC 32 Information technolo-gy/Data management and interchange
18-22 Sao Paulo (Brazil)
JTC 1/SC 40 Information tech-nology/IT Service Management and IT Governance
18-22 Chengdu (China) TC 39/SC 2 Machine tools/Test conditions for metal cutting machine tools
18-22 Luzern (Switzerland)
TC 114 Horology
19 London (United Kingdom)
TC 4/SC 8 Rolling bearings/Load ratings and life
19 Naples (Italy) TC 29/SC 5 Small tools/Grinding wheels and abrasives
19 Turin (Italy) TC 89/SC 3 Wood-based panels/Plywood
19 Luzern (Switzerland)
TC 114/SC 3 Horology/Water-resistant watches
20 London (United Kingdom)
TC 4/SC 11 Rolling bearings/Linear motion rolling bearings
20 Nagano (Japan) TC 20/SC 13 Aircraft and space vehicles/Space data and information trans-fer systems
20 Turin (Italy) TC 89 Wood-based panels
20 Turin (Italy) TC 89/SC 1 Wood-based panels/Fibre boards
20 Turin (Italy) TC 89/SC 2 Wood-based panels/Particle boards
20 Luzern (Switzerland)
TC 114/SC 14
Horology/Table and wall clocks
20 Copenhagen (Denmark)
TC 173/SC 7 Assistive products for persons with disabil-ity/Accessible design
20-21 Virtual (Unknown)
TC 22/SC 31 Road vehicles/Data communication
21 London (United Kingdom)
TC 4/SC 4 Rolling bearings/Tolerances, tolerance definitions and sym-bols (including GPS)
21 London (United Kingdom)
TC 4/SC 5 Rolling bearings/Needle, cylindrical and spherical roller bearings
21 London (United Kingdom)
TC 4/SC 7 Rolling bearings/Spherical plain bearings
21 London (United Kingdom)
TC 4/SC 12 Rolling bearings/Ball bearings
21 Luzern (Switzerland)
TC 114/SC 12
Horology/Antimagnetism
21 Los Angeles (USA)
TC 119/SC 2 Powder metallurgy/Sampling and testing methods for powders (including powders for hardmetals)
21 Los Angeles (USA)
TC 119/SC 3 Powder metallurgy/Sampling and testing methods for sintered metal materials (ex-cluding hardmetals)
ISO Update, Supplement to ISO Focus -- May 2015 17
21 Los Angeles (USA)
TC 119/SC 4 Powder metallurgy/Sampling and test-ing methods for hardmetals
21-22 Copenhagen (Denmark)
TC 173 Assistive products for persons with disability
21-22 Pretoria (South Africa)
TC 228 Tourism and related services
21-22 Yangzhou (China)
TC 293 Feed machinery
22 London (United Kingdom)
TC 4 Rolling bearings
22 Los Angeles (USA)
TC 119 Powder metallurgy
24-29 Tokyo (Japan) TC 113 Hydrometry
25 Tokyo (Japan) TC 113/SC 1 Hydrometry/Velocity area methods
25-29 Madrid (Spain) TC 23/SC 18 Tractors and machin-ery for agriculture and forestry/Irrigation and drainage equipment and systems
25-29 Vancouver (Canada)
TC 282/SC 2 Water re-use/Water re-use in urban areas
26 Tokyo (Japan) TC 113/SC 6 Hydrometry/Sediment transport
26-27 Ghent (Belgium) JTC 1/SC 6 Information technol-ogy/Telecommunica-tions and information exchange between systems
26-29 Buenos Aires (Argentina)
TC 85/SC 5 Nuclear energy, nuclear technolo-gies, and radiological protection/Nuclear fuel cycle
27 Geneva (Switzerland)
TAG 14 Image Technology
27 London (United Kingdom)
TC 67/SC 5 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Casing, tubing and drill pipe
27 Tokyo (Japan) TC 113/SC 8 Hydrometry/Ground water
27 Vancouver (Canada)
TC 282/SC 3 Water re-use/Risk and performance evaluation of water re-use systems
27-28 Vancouver (Canada)
TC 282/SC 1 Water re-use/Treated wastewater re-use for Irrigation
27-29 Panama (Panama)
TC 8/SC 1 Ships and marine technology/Lifesaving and fire protection
28 Virtual (Unknown)
President's committee
President's committee
28 Tokyo (Japan) TC 113/SC 2 Hydrometry/Flow measurement structures
28 Tokyo (Japan) TC 113/SC 5 Hydrometry/In-struments, equip-ment and data management
June 2015
1-4 Beijing (China) TC 46/SC 11 Information and doc-umentation/Archives/records management
1-4 Beijing (China) TC 249 Traditional chinese medicine
1-5 Arlington (USA) TC 20/SC 14 Aircraft and space ve-hicles/Space systems and operations
1-5 Guayaquil (Ecuador)
TC 34/SC 18 Food products/Cocoa
1-5 Sapporo (Japan) TC 42 Photography
1-5 Seattle (USA) TC 43/SC 3 Acoustics/Underwa-ter acoustics
1-5 Beijing (China) TC 46/SC 4 Information and documentation/Tech-nical interoperability
1-6 Philadelphia (USA)
TC 147 Water quality
2-4 Shizuoka City (Japan)
TC 34/SC 8 Food products/Tea
2-9 Matsue (Japan) JTC 1/SC 28 Information technol-ogy/Office equipment
3-4 Nanjing (China) TC 155 Nickel and nickel alloys
3-5 Glasgow, Scotland (United Kingdom)
TC 267 Facilities management
4 Beijing (China) TC 46/SC 8 Information and documentation/Quality - Statistics and performance evaluation
4 Beijing (China) TC 46/SC 9 Information and documentation/Identification and description
4 Beijing (China) TC 46/SC 10 Information and documentation/Requirements for document storage and conditions for preservation
4 Tokyo (Japan) TC 145/SC 1 Graphical symbols/Public information symbols
4-5 Montreal (Canada)
JTC 1/SC 31 Information technol-ogy/Automatic iden-tification and data capture techniques
4-5 Merida (Mexico) TC 242 Energy Management
5 Paris (France) TC 22/SC 36 Road vehicles/Safety aspects and impact testing
5 Beijing (China) TC 46 Information and documentation
5 Tokyo (Japan) TC 145 Graphical symbols
5 Tokyo (Japan) TC 145/SC 3 Graphical symbols/Graphical symbols for use on equipment
5-6 San Antonio (USA)
TC 85/SC 6 Nuclear energy, nuclear technolo-gies, and radiological protection/Reactor technology
8-9 Chicago (USA) TC 34/SC 15 Food products/Coffee
8-10 Arlington (USA) TC 20/SC 16 Aircraft and space vehicles/Unmanned aircraft systems
8-12 Houston (USA) TC 35 Paints and varnishes
18 ISO Update, Supplement to ISO Focus -- May 2015
8-12 Berlin (Germany) TC 121 Anaesthetic and res-piratory equipment
8-12 Berlin (Germany) * TC 121/SC 1 Anaesthetic and res-piratory equipment/Breathing attach-ments and anaes-thetic machines
8-12 Grasmere (Unit-ed Kingdom)
TC 268 Sustainable develop-ment in communities
9 Hokaido (Japan) TC 31/SC 6 Tyres, rims and valves/Off-the-road tyres and rims
9-10 New York (USA) TC 29/SC 10 Small tools/Assem-bly tools for screws and nuts, pliers and nippers
9-12 Pretoria (South Africa)
REMCO Committee on refer-ence materials
9-12 London (United Kingdom)
TC 289 Brand evaluation
10 Sapporo (Japan) TC 31/SC 7 Tyres, rims and valves/Industrial tyres and rims
10-11 La Plaine St-Denis (France)
TC 17/SC 9 Steel/Tinplate and blackplate
11 Sapporo (Japan) TC 31/SC 5 Tyres, rims and valves/Agricultural tyres and rims
11 Houston (USA) TC 35/SC 9 Paints and varnishes/General test meth-ods for paints and varnishes
11 Houston (USA) TC 35/SC 14 Paints and varnishes/Protective paint systems for steel structures
11 York (United Kingdom)
TC 238 Solid biofuels
11 Grasmere (Unit-ed Kingdom)
TC 268/SC 1 Sustainable develop-ment in communities/Smart community infrastructures
11-12 Paris (France) TC 24/SC 4 Particle charac-terization includ-ing sieving/Particle characterization
11-12 Southamp-ton (United Kingdom)
TC 211 Geographic in-formation/Geomatics
12 Zedelgem (Belgium)
TC 23/SC 7 Tractors and machin-ery for agriculture and forestry/Equipment for harvesting and conservation
15 Geneva (Switzerland)
President's committee
President's committee
15-16 Düsseldorf (Germany)
TC 17/SC 11 Steel/Steel castings
15-16 Kyoto (Japan) TC 22/SC 32 Road vehicles/Elec-trical and electronic components and gen-eral system aspects
15-18 Vancouver (Canada)
TC 22/SC 39 Road vehicles/Ergonomics
15-18 Boras (Sweden) TC 85/SC 2 Nuclear energy, nuclear technologies, and radiological pro-tection/Radiological protection
15-19 London (United Kingdom)
PC 277 Sustainable procurement
15-19 Vancouver (Canada)
** TC 22/SC 13 Road vehicles/Ergo-nomics applicable to road vehicles
15-19 Munich (Germany)
TC 94/SC 14 Personal safety -- Protective clothing and equipment/Fire-fighters' personal equipment
16-17 Zurich (Switzerland)
TC 17/SC 17 Steel/Steel wire rod and wire products
17-19 Berlin (Germany) TC 172/SC 9 Optics and photon-ics/Electro-optical systems
18 Geneva (Switzerland)
CSC/FIN Council/Council Standing Committee on Finance (CSC/FIN)
18-19 Stuttgart (Germany)
TC 184/SC 2 Automation systems and integration/Robots and robotic devices
18-19 Geneva (Switzerland)
TMB Technical Manage-ment Board
19 Beijing (China) TC 220 Cryogenic vessels
21-26 Matsue (Japan) TC 37 Terminology and other language and content resources
22-23 Dallas (USA) * TC 20/SC 17 Aircraft and space vehicles/Airport infrastructure
22-25 Avignon (France) TC 54 Essential oils
22-26 Rouen (France) JTC 1/SC 36 Information tech-nology/Information technology for learn-ing, education and training
22-26 Gjøvik (Norway) * JTC 1/SC 37 Information technology/Biometrics
22-26 (Netherlands) ** TC 34/SC 9 Food products/Microbiology
22-26 Dalian (China) TC 69 Applications of statis-tical methods
22-26 Dalian (China) TC 69/SC 5 Applications of sta-tistical methods/Ac-ceptance sampling
22-26 Dalian (China) TC 69/SC 6 Applications of statis-tical methods/Meas-urement methods and results
22-26 Dalian (China) TC 69/SC 8 Applications of sta-tistical methods/Ap-plication of statistical and related methodol-ogy for new technol-ogy and product development
22-26 La Plaine St-Denis (France)
TC 94/SC 6 Personal safety -- Protective clothing and equipment/Eye and face protection
22-26 Göteborg (Sweden)
* TC 188 Small craft
24 Porto (Portugal) ** TC 17/SC 15 Steel/Railway rails, rails fasteners, wheels and wheelsets
24 Stockholm (Sweden)
TC 149/SC 1 Cycles/Cycles and major sub-assemblies
ISO Update, Supplement to ISO Focus -- May 2015 19
24-25 Düsseldorf (Germany)
TC 17/SC 4 Steel/Heat treatable and alloy steels
24-26 St. Peters-burg (Russian Federation)
TC 20/SC 1 Aircraft and space vehicles/Aerospace electrical requirements
25 Göteborg (Sweden)
* TC 188/SC 2 Small craft/Engines and propulsion systems
26 Gaithersburg (USA)
TC 12 Quantities and units
26 Düsseldorf (Germany)
TC 159/SC 1 Ergonomics/General ergonomics principles
27 Warsaw (Poland) JTC 1/SC 29 Information technol-ogy/Coding of audio, picture, multimedia and hypermedia information
June-July 2015
30-3 Milan (Italy) * TC 193 Natural gas
30-3 Milan (Italy) * TC 193/SC 1 Natural gas/Analysis of natural gas
30-3 Milan (Italy) * TC 193/SC 3 Natural gas/Upstream area
July 2015
1-7 Berlin (Germany) TC 91 Surface active agents
2-3 Shanghai (China) TC 8/SC 4 Ships and marine technology/Outfitting and deck machinery
6-7 Helsinki (Finland) TC 44/SC 10 Welding and allied processes/Unification of requirements in the field of metal welding
6-9 Hamburg (Germany)
TC 8/SC 2 Ships and marine technology/Ma-rine environment protection
7-8 Helsinki (Finland) TC 44/SC 7 Welding and allied processes/Represen-tation and terms
8 Helsinki (Finland) TC 44/SC 5 Welding and allied processes/Testing and inspection of welds
8 Helsinki (Finland) TC 44/SC 9 Welding and allied processes/Health and safety
8 Bath (United Kingdom)
TC 184/SC 1 Automation systems and integration/Physi-cal device control
8-9 Berlin (Germany) TC 51 Pallets for unit load method of materials handling
9-10 Helsinki (Finland) TC 44 Welding and allied processes
14-17 Shanghai (China) TC 8/SC 8 Ships and marine technology/Ship design
16 Berlin (Germany) TC 261 Additive manufacturing
31 Arlington (USA) TC 86/SC 6 Refrigeration and air-conditioning/Testing and rating of air-conditioners and heat pumps
Hangzhou (China)
** TC 8/SC 13 Ships and marine technology/Marine technology
August 2015
24-28 Toronto (Canada) * TC 258 Project, programme and portfolio management
25-26 Beijing (China) TC 36 Cinematography
25-26 London (United Kingdom)
TC 105 Steel wire ropes
26-28 Jeju (Korea, Republic of)
TC 206 Fine ceramics
28 Uppsala (Sweden)
TC 46/SC 10 Information and documentation/Requirements for document storage and conditions for preservation
August-September 2015
31-4 Hokaido (Japan) * JTC 1/SC 35 Information technol-ogy/User interfaces
September 2015
4-12 New Delhi (India) ** TC 207 Environmental management
7 Tedding-ton (United Kingdom)
* TC 164/SC 2 Mechanical testing of metals/Ductility testing
7-11 Sydney (Australia)
TC 96/SC 9 Cranes/Bridge and gantry cranes
7-11 Tokyo (Japan) TC 133 Clothing sizing sys-tems - size designa-tion, size measure-ment methods and digital fittings
7-11 Paris (France) * TC 153 Valves
7-11 Tedding-ton (United Kingdom)
TC 164 Mechanical testing of metals
7-14 Sydney (Australia)
TC 96 Cranes
8-10 Tedding-ton (United Kingdom)
* TC 164/SC 5 Mechanical testing of metals/Fatigue testing
9 Tedding-ton (United Kingdom)
* TC 164/SC 1 Mechanical testing of metals/Uniaxial testing
9 Tedding-ton (United Kingdom)
* TC 164/SC 4 Mechanical testing of metals/Toughness testing -- Fracture (F), Pendulum (P), Tear (T)
10 Tedding-ton (United Kingdom)
TC 164/SC 3 Mechanical testing of metals/Hardness testing
10-11 Oslo (Norway) * TC 265 Carbon dioxide capture, transporta-tion, and geological storage
13 Seoul (Korea, Republic of)
* President's committee
President's committee
13 Seattle (USA) ** TC 201/SC 6 Surface chemi-cal analysis/Sec-ondary ion mass spectrometry
13-17 Lahaina, Hawaii (USA)
** TC 127 Earth-moving machinery
14 Seoul (Korea, Republic of)
* COUNCIL Council
20 ISO Update, Supplement to ISO Focus -- May 2015
14-15 Washington, D.C (USA)
* JTC 1/SC 22 Information technol-ogy/Programming languages, their envi-ronments and system software interfaces
14-17 Washington, D.C (USA)
TC 157 Non-systemic con-traceptives and STI barrier prophylactics
14-18 Milan (Italy) TC 43 Acoustics
14-18 Berlin (Germany) ** TC 150 Implants for surgery
14-18 (Canada) ** TC 205 Building environment design
14-25 Berlin (Germany) * TC 213 Dimensional and geometrical product specifications and verification
15 Seoul (Korea, Republic of)
* DEVCO Committee on devel-oping country matters
15 Vienna (Austria) * TC 33 Refractories
15 Seoul (Korea, Republic of)
* TMB Technical Manage-ment Board
15-17 Pittsburgh (USA) TC 94/SC 15 Personal safety -- Protective clothing and equipment/Respiratory protective devices
16-18 Seoul (Korea, Republic of)
* GA General Assembly
17 Kanazawa (Japan)
TC 142 Cleaning equipment for air and other gases
17-18 Delft (Netherlands)
TC 67 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries
17-18 (Canada) ** TC 163 Thermal performance and energy use in the built environment
18-19 Hawaii (USA) TC 23/SC 14 Tractors and machin-ery for agriculture and forestry/Operator controls, operator symbols and other displays, operator manuals
20-26 Williamsburg (USA)
* TC 27 Solid mineral fuels
21-25 Poznan (Poland) ** TC 23/SC 6 Tractors and machin-ery for agriculture and forestry/Equipment for crop protection
21-25 Delft (Netherlands)
TC 146/SC 6 Air quality/Indoor air
21-25 Johor Bahru (Malaysia)
TC 165 Timber structures
22 Berlin (Germany) TC 111/SC 1 Round steel link chains, chain slings, components and ac-cessories/Chains and chain slings
23-24 (China) ** TC 290 Online reputation
24-25 Gouda (Netherlands)
* TC 34/SC 11 Food products/Animal and vegetable fats and oils
25 Delft (Netherlands)
TC 146/SC 1 Air quality/Stationary source emissions
28-29 Basel (Switzerland)
** TC 44/SC 8 Welding and allied processes/Equip-ment for gas welding, cutting and allied processes
29 Paris (France) TC 86/SC 1 Refrigeration and air-conditioning/Safety and environmental requirements for re-frigerating systems
29-30 Tokyo (Japan) * TC 44/SC 3 Welding and allied processes/Welding consumables
(Europe) ** TC 22/SC 19 Road vehicles/Wheels
14-18 Milan (Italy) TC 43/SC 1 Acoustics/Noise
14-18 Milan (Italy) TC 43/SC 2 Acoustics/Building acoustics
Berlin (Germany) ** TC 146/SC 2 Air quality/Workplace atmospheres
September-October 2015
27-3 Bangkok (Thailand)
* TC 106 Dentistry
28-2 Kuala Lumpur (Malaysia)
** PC 278 Anti-bribery manage-ment systems
28-2 Edmonton (Canada)
TC 229 Nanotechnologies
October 2015
1 Rome (Italy) * TC 39/SC 4 Machine tools/Wood-working machines
2 Paris (France) TC 86/SC 8 Refrigeration and air-conditioning/Refriger-ants and refrigeration lubricants
5 Bloomington (USA)
** TC 23/SC 13 Tractors and machin-ery for agriculture and forestry/Powered lawn and garden equipment
5 Madrid (Spain) TC 59 Buildings and civil engineering works
5-9 Dublin (Ireland) * JTC 1/SC 38 Information technol-ogy/Cloud Comput-ing and Distributed Platforms
5-9 Madrid (Spain) * TC 59/SC 3 Buildings and civil engineering works/Functional/user requirements and performance in build-ing construction
5-9 Madrid (Spain) * TC 59/SC 15 Buildings and civil engineering works/Performance descrip-tion of houses
5-9 Madrid (Spain) * TC 59/SC 16 Buildings and civil engineering works/Accessibility and usability of the built environment
5-9 Vienna (Austria) * TC 190 Soil quality
5-9 Vienna (Austria) * TC 190/SC 2 Soil quality/Sampling
5-9 Vienna (Austria) * TC 190/SC 3 Soil quality/Chemi-cal methods and soil characteristics
5-9 Vienna (Austria) * TC 190/SC 4 Soil quality/Biological methods
5-9 Vienna (Austria) * TC 190/SC 7 Soil quality/Soil and site assessment
ISO Update, Supplement to ISO Focus -- May 2015 21
6 Lyon (France) * IULTCS International Union of Leather Technolo-gists and Chemists Societies
8 Virtual (Unknown)
* President's committee
President's committee
8-9 Sao Paulo (Brazil)
* TC 58/SC 2 Gas cylinders/Cylin-der fittings
9 Copenhagen (Denmark)
TC 254 Safety of amusement rides and amusement devices
12 Beijing (China) * TC 20/SC 4 Aircraft and space vehicles/Aerospace fastener systems
12-16 Paris (France) * TC 34/SC 17 Food products/Man-agement systems for food safety
12-16 Turin (Italy) ** TC 70 Internal combustion engines
12-16 Beijing (China) * TC 181 Safety of toys
13 Beijing (China) * TC 20/SC 8 Aircraft and space vehicles/Aerospace terminology
13 Lyon (France) * TC 38/SC 1 Textiles/Tests for coloured textiles and colorants
13 Lyon (France) * TC 38/SC 2 Textiles/Cleansing, finishing and water resistance tests
13-14 Osaka (Japan) * TC 24/SC 4 Particle charac-terization includ-ing sieving/Particle characterization
14 Lyon (France) * TC 38/SC 23 Textiles/Fibres and yarns
14 Lyon (France) * TC 38/SC 24 Textiles/Condition-ing atmospheres and physical tests for textile fabrics
14-15 Beijing (China) * TC 20 Aircraft and space vehicles
14-16 Renton (USA) * TC 44/SC 14 Welding and allied processes/Weld-ing and brazing in aerospace
15 Lyon (France) * TC 38 Textiles
15-17 Seattle (USA) * TC 201 Surface chemical analysis
16 San Diego (USA) * TC 22/SC 34 Road vehicles/Propul-sion, powertrain and powertrain fluids
18-23 Vichy (France) TC 45 Rubber and rubber products
18-23 Vichy (France) TC 45/SC 4 Rubber and rubber products/Products (other than hoses)
18-23 Baltimore (USA) * TC 184/SC 4 Automation systems and integration/Indus-trial data
19-21 Jeju (Korea, Republic of)
* TC 281 Fine Bubble Technology
19-22 Vichy (France) TC 45/SC 1 Rubber and rubber products/Rubber and plastics hoses and hose assemblies
19-23 (Germany) ** TC 39/SC 2 Machine tools/Test conditions for metal cutting machine tools
19-23 Gaithersburg (USA)
* TC 92 Fire safety
19-23 Gaithersburg (USA)
* TC 92/SC 1 Fire safety/Fire initia-tion and growth
19-23 Brussels (Belgium)
TC 154 Processes, data elements and documents in com-merce, industry and administration
20 Metz (France) TC 173/SC 2 Assistive products for persons with disabil-ity/Classification and terminology
20-23 Oslo (Norway) ** TC 58/SC 3 Gas cylinders/Cylin-der design
20-23 Beijing (China) * TC 269 Railway applications
21-23 Katowize (Poland)
TC 263 Coalbed methane (CBM)
22 Santiago (Chile) TC 195 Building construc-tion machinery and equipment
22-23 London (United Kingdom)
* TC 79/SC 2 Light metals and their alloys/Or-ganic and anodic oxidation coatings on aluminium
22-23 Berlin (Germany) TC 209 Cleanrooms and as-sociated controlled environments
26-29 Pretoria (South Africa)
** TC 264 Fireworks
26-30 St. Peters-burg (Russian Federation)
TC 8 Ships and marine technology
26-30 Porto Alegre (Brazil)
TC 23/SC 17 Tractors and machin-ery for agriculture and forestry/Manu-ally portable forest machinery
26-31 (China) ** JTC 1 Information technology
27-29 Berlin (Germany) * TC 256 Pigments, dyestuffs and extenders
28-30 Tsukuba (Japan) ** TC 202 Microbeam analysis
29 Seoul (Korea, Republic of)
* TC 71 Concrete, reinforced concrete and pre-stressed concrete
29 Silver Spring (USA)
TC 234 Fisheries and aquaculture
29-30 Tampa, Florida (USA)
* TC 17/SC 12 Steel/Continuous mill flat rolled products
(Unknown) ** TC 2 Fasteners
Madrid (Spain) ** TC 10/SC 8 Technical prod-uct documenta-tion/Construction documentation
(Netherlands) ** TC 34/SC 2 Food products/Ole-aginous seeds and fruits and oilseed meals
Washington, D.C (USA)
** TC 79 Light metals and their alloys
Rio de Janeiro (Brazil)
** TC 130 Graphic technology
Sao Paulo (Brazil)
** TC 135/SC 9 Non-destructive test-ing/Acoustic emission testing
22 ISO Update, Supplement to ISO Focus -- May 2015
(Germany) ** TC 244 Industrial furnaces and associated pro-cessing equipment
(China) ** TC 282/SC 3 Water re-use/Risk and performance evaluation of water re-use systems
November 2015
2 Atlanta (USA) * TC 41/SC 3 Pulleys and belts (including veebelts)/Conveyor belts
2-6 Bern (Switzerland)
TC 215 Health informatics
2-6 Beijing (China) * TC 282 Water re-use
3 Atlanta (USA) * TC 41/SC 1 Pulleys and belts (including veebelts)/Friction
3 Berlin (Germany) * TC 83 Sports and other recreational facilities and equipment
3-5 Montreal (Canada)
TC 20/SC 9 Aircraft and space vehicles/Air cargo and ground equipment
3-6 Accra (Ghana) ** TC 285 Clean cookstoves and clean cooking solutions
4 Atlanta (USA) TC 41/SC 4 Pulleys and belts (including veebelts)/Synchronous belt drives
4 (Australia) ** TC 110/SC 1 Industrial trucks/Gen-eral terminology
5 Atlanta (USA) * TC 41 Pulleys and belts (including veebelts)
6 (Australia) ** TC 110 Industrial trucks
6 (Australia) ** TC 110/SC 5 Industrial trucks/Sustainability
9-12 (Spain) ** TC 189 Ceramic tile
9-13 London (United Kingdom)
* PC 287 Chain of custody of wood and wood-based products
9-13 Kobe (Japan) * TC 21 Equipment for fire protection and fire fighting
9-13 Tokyo (Japan) TC 94/SC 15 Personal safety -- Protective clothing and equipment/Respiratory protective devices
9-13 Sydney (Australia)
* TC 275 Sludge recovery, recycling, treatment and disposal
9-14 Galveston (USA) * TC 260 Human resource management
10-13 (Switzerland) ** TC 112 Vacuum technology
11 Vicenza (Italy) * TC 44/SC 13 Welding and allied processes/Braz-ing materials and processes
11 Notting-ham (United Kingdom)
* TC 60 Gears
11-13 (Malaysia) ** TC 123 Plain bearings
11-13 Geel (Belgium) TC 212 Clinical laboratory testing and in vitro di-agnostic test systems
12-13 Kuala Lumpur (Malaysia)
** TC 227 Springs
16 (USA) ** PC 252 Natural gas fuelling stations for vehicles
16-20 Kyoto (Japan) TC 160 Glass in building
16-20 (USA) ** TC 210 Quality management and corresponding general aspects for medical devices
16-21 Washington, D.C (USA)
* TC 98/SC 3 Bases for design of structures/Loads, forces and other actions
20-28 Hong Kong (Hong Kong, China)
* TC 176 Quality management and quality assurance
23-27 Ardooie (Belgium)
TC 188/SC 1 Small craft/Personal safety equipment
Istanbul (Turkey) ** TC 120 Leather
November-December 2015
16-21 Virginia (USA) TC 98 Bases for design of structures
December 2015
3-4 Torrance (USA) * TC 197 Hydrogen technologies
10 Berlin (Germany) * TC 44/SC 6 Welding and allied processes/Resistance welding and allied mechanical joining
14-18 Berlin (Germany) TC 198 Sterilization of health care products
Istanbul (Turkey) ** TC 180 Solar energy
(United Arab Emirates)
** TC 217 Cosmetics
4th Quarter 2015
(Sweden) ** TC 17/SC 1 Steel/Methods of de-termination of chemi-cal composition
Dayton, Ohio (USA)
** TC 159/SC 3 Ergonomics/An-thropometry and biomechanics
Tel Aviv (Israel) ** TC 282 Water re-use
(Indonesia) ** TC 292 Security
2nd Semester 2015
(France) ** TC 172/SC 1 Optics and photon-ics/Fundamental standards
Month unknown 2015
Berlin (Germany) ** TC 138 Plastics pipes, fittings and valves for the transport of fluids
January 2016
25-29 London (United Kingdom)
** TC 107 Metallic and other inorganic coatings
25-29 London (United Kingdom)
** TC 107/SC 3 Metallic and other inorganic coatings/Electrodeposited coatings and related finishes
25-29 London (United Kingdom)
** TC 107/SC 8 Metallic and other inorganic coatings/Chemical conversion coatings
February 2016
26 Nairobi (Kenya) * TMB Technical Manage-ment Board
ISO Update, Supplement to ISO Focus -- May 2015 23
(South Africa) ** TC 58/SC 4 Gas cylinders/Opera-tional requirements for gas cylinders
(USA) ** TC 213 Dimensional and geometrical product specifications and verification
(United Kingdom)
** TC 257 Evaluation of energy savings
March 2016
3-4 (Unknown) ** TC 182/SC 1 Geotechnics/Geo-technical investiga-tion and testing
14-18 Sydney (Australia)
** TC 108/SC 2 Mechanical vibration, shock and condition monitoring/Measure-ment and evalua-tion of mechanical vibration and shock as applied to ma-chines, vehicles and structures
14-18 Sydney (Australia)
** TC 108/SC 5 Mechanical vibration, shock and condition monitoring/Condition monitoring and diag-nostics of machine systems
17-18 Geneva (Switzerland)
* COUNCIL Council
1st Quarter 2016
Singapore (Singapore)
** TC 67/SC 7 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Offshore structures
April 2016
11-15 Sydney (Australia)
** TC 178 Lifts, escalators and moving walks
25-29 Berlin (Germany) ** TC 161 Control and protec-tive devices for gas and/or oil burners and appliances
Toronto (Canada) ** JTC 1/SC 38 Information technol-ogy/Cloud Comput-ing and Distributed Platforms
May 2016
9-13 (USA) ** TC 276 Biotechnology
22-27 Sapporo (Japan) * TC 184/SC 4 Automation systems and integration/Indus-trial data
25 Brussels (Belgium)
** TC 115 Pumps
(Brazil) ** TC 67/SC 4 Materials, equipment and offshore struc-tures for petroleum, petrochemical and natural gas industries/Drilling and produc-tion equipment
(India) ** TC 85 Nuclear energy, nuclear technolo-gies, and radiological protection
(Korea, Repub-lic of)
** TC 122 Packaging
Stockholm (Sweden)
** TC 130 Graphic technology
(USA) ** TC 282/SC 3 Water re-use/Risk and performance evaluation of water re-use systems
June 2016
15-16 Geneva (Switzerland)
* TMB Technical Manage-ment Board
18-20 Munich (Germany)
TC 135 Non-destructive testing
(Germany) ** JTC 1/SC 36 Information tech-nology/Information technology for learn-ing, education and training
(Europe) ** TC 22/SC 38 Road vehicles/Motor-cycles and mopeds
St. Peters-burg (Russian Federation)
** TC 172/SC 4 Optics and photonics/Telescopic systems
2nd Quarter 2016
(Germany) ** TC 34/SC 4 Food products/Cere-als and pulses
1st Semester 2016
(France) ** TC 23 Tractors and machin-ery for agriculture and forestry
New Delhi (India) ** TC 34/SC 7 Food products/Spic-es, culinary herbs and condiments
(China) ** TC 34/SC 16 Food products/Hori-zontal methods for molecular biomarker analysis
Chennai (India) ** TC 120 Leather
September 2016
19 Beijing (China) * COUNCIL Council
20 Beijing (China) * TMB Technical Manage-ment Board
21-23 Beijing (China) * GA General Assembly
Vienna (Austria) ** JTC 1/SC 22 Information technol-ogy/Programming languages, their envi-ronments and system software interfaces
Paris (France) ** TC 17 Steel
Sao Paulo (Brazil)
** TC 209 Cleanrooms and as-sociated controlled environments
Shanghai (China) ** TC 213 Dimensional and geometrical product specifications and verification
Beijing (China) ** TC 256 Pigments, dyestuffs and extenders
3rd Quarter 2016
(USA) ** TC 289 Brand evaluation
October 2016
17-21 Berlin (Germany) ** JTC 1/SC 38 Information technol-ogy/Cloud Comput-ing and Distributed Platforms
17-21 (China) ** TC 5/SC 2 Ferrous metal pipes and metallic fittings/Cast iron pipes, fit-tings and their joints
20-21 London (United Kingdom)
* TC 58 Gas cylinders
24 ISO Update, Supplement to ISO Focus -- May 2015
(Brazil) ** TC 59 Buildings and civil engineering works
(Korea, Repub-lic of)
** TC 201 Surface chemical analysis
(Israel) ** TC 282/SC 3 Water re-use/Risk and performance evaluation of water re-use systems
November 2016
(Norway) ** JTC 1 Information technology
4th Quarter 2016
Delft (Netherlands)
** TC 28 Petroleum products and related products of synthetic or bio-logical origin
Delft (Netherlands)
** TC 28/SC 5 Petroleum products and related products of synthetic or bio-logical origin/Meas-urement of refriger-ated hydrocarbon and non-petroleum based liquefied gaseous fuels
Delft (Netherlands)
** TC 28/SC 7 Petroleum products and related products of synthetic or bio-logical origin/Liquid Biofuels
Month unknown 2016
(Korea, Repub-lic of)
** JTC 1/SC 23 Information technolo-gy/Digitally Recorded Media for Informa-tion Interchange and Storage
(Russian Federation)
** REMCO Committee on refer-ence materials
(Denmark) ** TC 37 Terminology and other language and content resources
(South Africa) ** TC 44 Welding and allied processes
(Malaysia) ** TC 45 Rubber and rubber products
Wellington (New Zealand)
** TC 46 Information and documentation
Wellington (New Zealand)
** TC 46/SC 11 Information and doc-umentation/Archives/records management
(Japan) ** TC 94/SC 13 Personal safety -- Protective clothing and equipment/Pro-tective clothing
(Sweden) ** TC 102 Iron ore and direct reduced iron
(Japan) ** TC 138/SC 2 Plastics pipes, fittings and valves for the transport of fluids/Plastics pipes and fittings for water supplies
(Japan) ** TC 183 Copper, lead, zinc and nickel ores and concentrates
April 2017
10 Guilin (China) ** TC 29/SC 8 Small tools/Tools for pressing and moulding
May 2017
(Sweden) ** TC 29 Small tools
June 2017
(Australia) ** JTC 1/SC 36 Information tech-nology/Information technology for learn-ing, education and training
September 2017
London (United Kingdom)
** JTC 1/SC 22 Information technol-ogy/Programming languages, their envi-ronments and system software interfaces
New Delhi (India) ** TC 178 Lifts, escalators and moving walks
3rd Quarter 2017
Vienna (Austria) ** TC 289 Brand evaluation
Month unknown 2017
(United Kingdom)
** TC 94/SC 13 Personal safety -- Protective clothing and equipment/Pro-tective clothing
Seoul (Korea, Republic of)
** TC 161 Control and protec-tive devices for gas and/or oil burners and appliances
June 2018
(Korea, Repub-lic of)
** JTC 1/SC 36 Information tech-nology/Information technology for learn-ing, education and training
Month unknown 2018
(USA) ** TC 94/SC 13 Personal safety -- Protective clothing and equipment/Pro-tective clothing
Milan (Italy) ** TC 161 Control and protec-tive devices for gas and/or oil burners and appliances