1 of 4 00000050209

L.L.Bean

Studio Platform Bed

Thank you for purchasing our Studio Platform Bed. Assembly of this product requires a Phillips head and a flat head screwdriver. We have found it helpful to have a second person present in at least one step of the assembly.

2 of 4 00000050209

STEP 1 Read through these instructions thoroughly before beginning assembly. We have found this to be of great value when first assembling this product. STEP 2 Remove all parts and hardware from packing material. Wooden pieces should be placed on a non abrasive surface (like the carton or carpet) to prevent damage to the finish. STEP 3 Identify all parts using parts list at right

PARTS

A. SIDE RAIL (2) B. HEADBOARD END/FOOTBOARD END (2) C. LONG SUPPORT BAR (FULL, QUEEN and KING)* D. SMALL WOODEN LEG (FULL, QUEEN and KING)* E. WEBBED SLAT SYSTEM

*King size will have 2

STEP 4 Identify and count hardware using diagram at right and the list below. Hardware: 8 – 3 ½” Bolts 8 – Barrel Nuts 2 – Screws 4 – 1 ¼” Wooden Dowels 1 – Center Leg Hardware (3 ½” bolt & barrel nut)* *NOTE: Twin size will not use the center leg hardware, Full & Queen size will be as pictured, and King size will include 2 sets. Assembly of this product requires a Phillips head and a flat head screwdriver. We have found it helpful to have a second person present in at least one step of the assembly.

STEP 5 Locate the two side rails, the center support bar, the center support leg, and the headboard and footboard ends. STEP 6 Place the rails finish side down on a carpeted surface or padded floor.

STEP 7 After separating out the center leg hardware, locate the remaining 8 bolts and 8 barrel nuts. Insert the barrel nuts into the holes on the inside of the side rails with the slot in the barrel nut facing up. Turn the slot on the end of each barrel nut so that it is going the length of the rail.

3 of 4 00000050209

STEP 8 Find the headboard end of the bed. The ends are identical so the headboard and footboard ends are interchangeable. STEP 9 Line up the end of one rail (finished side out) with the pre-drilled holes in the headboard end of the bed. The front of the headboard end should be facing the rails at this point. From the back of the headboard end, thread a bolt through each hole in the headboard end into the corresponding hole in the side rail so that it screws into the barrel nut placed in the rail in step #13. Using a Phillips head screwdriver tighten the bolt until it is completely threaded into the barrel nut (the use of a flat head screwdriver to hold the barrel nut in the correct position is recommended). IMPORTANT: DO NOT tighten the bolts completely at this point. Repeat this process for the other rail. STEP 10 Locate the footboard end of the bed and repeat step #9 to attach.

Twin size skip to step #13

STEP 11 Attaching center support bar(s):

FULL & QUEEN SIZE – Locate the long support bar with the screws attached to each end. Line up the support bar so that the screws at each end fit into the notch on the metal brackets found on the inside of the frame ends. It is important that the end of the support bar with the red dot is at the head of the bed. Push down to lock into place.

KING SIZE – Follow Full & Queen size directions for both support bars.

STEP 12 (ALL SIZES) Go back and tighten the bolts left loose in step #9 and step #10.

STEP 13 Locate the four 1¼” fluted dowels. Put one dowel into each of the pre-drilled holes located on the inside edges of the rails. Tap into place.

4 of 4 00000050209

STEP 14 Installing slats and center leg:

TWIN SIZE: Unroll the webbed slat system into the frame with the webbing down. IMPORTANT: DO NOT cut or remove the webbing. The last slat on each end will fit into place on the outside of the dowels put into position in step #13.

FULL, QUEEN, and KING SIZE: Unroll the webbed slat system into the frame with the webbing down. IMPORTANT: DO NOT cut or remove the webbing. Make sure the slat with the red dot is at the head of the bed (to correspond with the dot on the center support bar). Place the slat with the red dot on the outside of the dowels at the head of the bed that were put in place in step #13. Stretch out the slat system halfway until each hole in the center slat lines up with the slot in each center support bar. Locate the center support leg and place a barrel nut in the hole drilled on the side of the leg, making sure the groove on the barrel nut faces out.

Stand the leg under the slot in the center support bar. Thread a bolt through the center slat, through the center support bar and into the center leg. Tighten completely.

STEP 14 Once all center legs are installed, finish stretching out the slat system and place the last slat on the outside of the dowel at the foot of the bed. STEP 15 Using the screws provided, screw the middle slat onto the side rails through the pre-drilled holes. STEP 16 Tap the wood buttons into place on the outside of the headboard and footboard to cover the bolt holes.

CARE Use a clean soft cloth to dust.

www.llbean.com

Product Support 1-800-341-4341