Standard Products - Wagner

ELBOWS

MISCELLANEOUS PRODUCTS

BRACKETS

BIKE RACKS

SLIP-ON FITTINGS

SPHERES / HEMISPHERES / POST & END CAPS

FLANGES

CONNECTORS

Standard Products

shopwagner.com 37

Rr

Rr

Rr

C-C

Deformity Issues with Stock BendsThe process of bending Pipe and Tube results in unavoidable deformation.In round sections, this causes some ovality in the bent sections of material that may result in a mismatch between the Elbow and stock, straight material. The deformation may be as much as +5% in the vertical dimension and -5% in the horizontal dimension.This may be avoided by ordering Elbows with Tangents since the tangent sections will be unaffected by the bending process.

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

STEEL ALUMINUM 3003 Seamed Elbows 6061 Tubing Elbows 6063 Pipe ElbowsSTAINLESS STEEL Type 304BRASS C33000BRONZE C23000• Stainless Steel Type 316 and Bronze Alloy C38500 are available

upon request.

Made in MILWAUKEEFlush Weld Fittings

Clean, aesthetic Flush Fittings are utilized in the assembly of Railings joined by Wagner’s unique Wedge-Lock™ Weld Connectors shown on page 32. After welding and grinding smooth, the railing section is complete and ready for installation. Or wire weld with no grinding – as shown. Wedge-Locks are available for Pipe and Tube sizes – see page 32.

90° ElbowThese Elbows have no visible seam unless noted.

Pipe Size OD

Wall Thick. r R STEEL ALUMINUM STAINLESS

1.50" .120" 1.50" 2.25" 7914* 7930* 7946*2.50" .120" 3.75" 5.00" 9610 9613

2 1/2" 2.880" .203" 3.56" 5.00" 9600 96033.00" .120" 3.50" 5.00" 9623

3" 3.50" .216" 4.25" 6.00" 96304" 4.50" .237" 5.75" 8.00" 9640 9643

* Denotes an Elbow with a seam.

90° Elbow with Two 4" Tangents These Elbows have no visible seam unless noted.

Pipe Size OD

Wall Thick. r R STEEL ALUMINUM STAINLESS

2 1/2" 2.880" .203" 3.56" 5.00" 9601 96043.00" .120" 3.50" 5.00" 9621 9624 9626

3" 3.50" .216" 4.25" 6.00" 9631 96344" 4.50" .237" 5.75" 8.00" 9641

180° Elbow with Two 4" Tangents These Elbows have no visible seam unless noted.

Pipe Size OD

Wall Thick. r R C-C STEEL ALUMINUM

2.50" .120" 3.75" 5.00" 10.00" 96152 1/2" 2.88" .203" 3.56" 5.00" 10.00" 9605

3.00" .120" 3.50" 5.00" 12.00" 96223" 3.50" .216" 4.25" 6.00" 12.00" 9632

Miscellaneous Radius Pipe and OD Tube ElbowsThese Handrail Bends are mandrel bent and have no visible seam unless noted.Elbows are supplied with a mill finish. They are also available galvanized, zinc plated, anodized or polished to a satin or bright finish.

90° Elbows and Connectors

Coped Drive-On Welding Connectors

35° Elbows and Connectors

(2) 90° Elbows and Connectors

Typical Pipe Stair Railings

Wedge-Lock Connector

Weld No Grinding Ready to Paint

r = Inside Radius R = Center Line Radius C-C = Center to Center Diameter

Miscellaneous Radius Pipe and OD Tube Elbows

38 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914

cb

a

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

cba

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

cb

a

a a

a a

a

d

cb

d

NUMBERS IN BOLD TYPE are typically in stock. Other items may not be available for immediate shipment or are made-to-order – requiring a minimum quantity and a longer lead time. Visit shopwagner.com for availability.

The following options are available on special order – contact [email protected]:• Polished, galvanized or

anodized finishes.• Returns for 1.25" and 2.00" OD Tubing.• Variations in the center-line projections.

Wall Returns for 1.50" Tubing are designed to meet the 1991 ADA guidelines requiring a 1 1/2" clearance between the wall and Handrail. Newer ICC, NFPA, ANSI and the 2010 ADASAD now note this as a minimum clearance. Confirm your local requirements before specifying any Wagner product. Refer to page 226 for code and accessibility information.

Square Flange ReturnsRefer to page 64 for Square Flush Base Flanges which may be used to assemble Wall Returns for square or round Handrail sections.

Returns with Square Flush Base Flanges and Elbows

Aluminum Wall Returns are made from a combination of the following Alloys: 3003, 6061 and 6063. Stainless Steel Wall Returns are Type 304.

Wall Return with One 3/8" Hole and 2" Tangent*Pipe Size OD

Wall Thick. a b c d ALUMINUM

SATINSTAINLESS STEEL

1.50" .120" 4.91" 1.50" 2.25" 3.50" 1151-1 1152-11 1/4" 1.66" .140" 6.00" 1.67" 2.50" 3.50" 1109-1 1115-1 1105-11 1/4" 1.66" .140" 6.38" 2.17" 3.00" 3.50" 1112-1 1118-11 1/4" 1.66" .140" 6.38" 2.42" 3.25" 3.50" 1161-1 1162-1 1163-11 1/2" 1.90" .145" 6.00" 1.55" 2.50" 3.50" 1139-1 1145-11 1/2" 1.90" .145" 6.50" 2.05" 3.00" 3.50" 1142-1 1148-11 1/2" 1.90" .145" 6.50" 2.30" 3.25" 3.50" 1165-1 1166-1

Flush Weld Wall Return with One 3/8" HolePipe Size OD

Wall Thick. a b c d STEEL

1.50" .120" 3.81" 1.50" 2.25" 3.50" 1150-11 1/4" 1.66" .140" 3.88" 1.67" 2.50" 3.50" 1100-11 1/4" 1.66" .140" 4.44" 2.17" 3.00" 3.50" 1103-11 1/4" 1.66" .140" 4.44" 2.42" 3.25" 3.50" 1160-11 1/2" 1.90" .145" 3.75" 1.55" 2.50" 3.50" 1130-11 1/2" 1.90" .145" 4.44" 2.05" 3.00" 3.50" 1133-11 1/2" 1.90" .145" 4.44" 2.30" 3.25" 3.50" 1164-1

Wall Return with Two 5/16" Holes and 2" TangentPipe Size OD


SATINSTAINLESS

1.50" .120" 4.35" 1.50" 2.25" 3.88" 1151-2 1152-21 1/4" 1.66" .140" 4.44" 1.67" 2.50" 3.88" 1109-2 1115-21 1/4" 1.66" .140" 4.81" 2.17" 3.00" 3.88" 1112-2 1118-21 1/4" 1.66" .140" 4.81" 2.42" 3.25" 3.88" 1161-2 1162-21 1/2" 1.90" .145" 4.56" 1.55" 2.50" 4.44" 1139-2 1145-21 1/2" 1.90" .145" 4.94" 2.05" 3.00" 4.44" 1142-2 1148-21 1/2" 1.90" .145" 4.94" 2.30" 3.25" 4.44" 1165-2 1166-2

Flush Weld Wall Return with Two 5/16" HolesPipe Size OD


1.50" .120" 2.25" 1.50" 2.25" 3.88" 1150-21 1/4" 1.66" .140" 2.44" 1.67" 2.50" 3.88" 1100-21 1/4" 1.66" .140" 2.88" 2.17" 3.00" 3.88" 1103-21 1/4" 1.66" .140" 2.88" 2.42" 3.25" 3.88" 1160-21 1/2" 1.90" .145" 2.25" 1.55" 2.50" 4.44" 1130-21 1/2" 1.90" .145" 2.94" 2.05" 3.00" 4.44" 1133-21 1/2" 1.90" .145" 2.94" 2.30" 3.25" 4.44" 1164-2

Wall Return with Three 5/16" Holes and 2" TangentPipe Size OD


SATINSTAINLESS

1.50" .120" 5.85" 1.50" 2.25" 3.88" 1151-3 1152-31 1/4" 1.66" .140" 5.94" 1.67" 2.50" 3.88" 1109-3 1115-31 1/4" 1.66" .140" 6.38" 2.17" 3.00" 3.88" 1112-3 1118-31 1/4" 1.66" .140" 6.38" 2.42" 3.25" 3.88" 1161-31 1/2" 1.90" .145" 6.69" 1.55" 2.50" 4.50" 1139-3 1145-31 1/2" 1.90" .145" 6.75" 2.05" 3.00" 4.50" 1142-3 1148-31 1/2" 1.90" .145" 6.75" 2.30" 3.25" 4.50" 1165-3 1166-3

Flush Weld Wall Return with Three 5/16" HolesPipe Size OD


1.50" .120" 3.75" 1.50" 2.25" 3.88" 1150-31 1/4" 1.66" .140" 3.94" 1.67" 2.50" 3.88" 1100-31 1/4" 1.66" .140" 4.38" 2.17" 3.00" 3.88" 1103-31 1/4" 1.66" .140" 4.38" 2.42" 3.25" 3.88" 1160-31 1/2" 1.90" .145" 4.00" 1.55" 2.50" 4.44" 1130-31 1/2" 1.90" .145" 4.69" 2.05" 3.00" 4.44" 1133-31 1/2" 1.90" .145" 4.38" 2.30" 3.25" 4.44" 1164-3

Flush Weld Wall ReturnsMade in

MILWAUKEE

* Refer to page 77 for Wall Returns with 18" Tangents

Wall Returns

shopwagner.com 39

Rr

C-C

Rr

Rr

Rr

Rr

Rr

35° Elbow Cut to order. Ship within 48 hours.These Elbows have a seam unless noted.

Pipe Size Sch. OD

Wall Thick. STEEL ALUMINUM STAINLESS

3/4" 40 1.05" .113" 151†

1" 40 1.315" .133" 2001 1/4" 40 1.66" .140" 248 272 2971 1/2" 40 1.90" .145" 320 344 3692" 40 2.375" .154" 392†

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

1" Inside Radius Flush Weld ElbowsThese 1" inside radius Elbows have a seam – unless noted. 90° and 180° Elbows with tangents are mandrel bent and have no seam. The 1" inside radius on these Elbows is tighter than anyone else's in the market.Elbows are supplied with a mill finish. They are available galvanized, zinc plated, anodized or polished to a satin or bright finish. All Elbows may also be purchased with tangents. Contact Wagner with your requirements.See page 32 for optional Wedge-Lock™ Connectors. See page 38 for typical Wall Returns.See page 41 for issues relating to deformation in bent Elbows.

NominalPipe Size OD

Inside Radius (r)

Center Line Radius

(R)

Theoretical Center to Center

Diam. (C-C)3/4" 1.05" 1.00" 1.525" 3.05"1" 1.315" 1.00" 1.658" 3.316"

1 1/4" 1.66" 1.00" 1.83" 3.66"1 1/2" 1.90" 1.00" 1.95" 3.90"2" 2.375" 1.00" 2.188"

Optional Wedge-Lock Connectors for Alignment

and Decreased Grinding Time. Refer to page 32.

254 Steel 45° 1" IR

269-6 Steel 180° 1" IR with Two Tangents

180° Elbow with Two 2" Tangents Without Seam

Pipe Size Sch. OD


3/4" 40 1.05" .113" 159† 169†

1" 40 1.315" .133" 218-4ß† 242-4† 219S-4†

1 1/4" 40 1.66" .140" 266-4† 290-4ß†

1 1/2 " 40 1.90" .145" 338-4ß† 362-4ß†

† Denotes an Elbow without a seam.

90° Elbow with Two 2" TangentsWithout Seam

Pipe Size Sch. OD


3/4" 40 1.05" .113" 157-8† 166†

1" 40 1.315" .133" 218-2† 242-2† 219S-2†

1 1/4" 40 1.66" .140" 266-2† 290-2† 315-2†

1 1/2" 40 1.90" .145" 338-2† 362-2† 387-2†

90° ElbowThese Elbows have a seam unless noted.

Pipe Size Sch. OD


3/4" 40 1.05" .113" 157† 167†

1" 40 1.315" .133" 218 242 219-S1" 40 1.315" .133" 218-S† 242-S†

1 1/4" 40 1.66" .140" 266 290 3151 1/4" 40 1.66" .140" 290-S†1 1/2" 40 1.90" .145" 338 362 3871 1/2" 40 1.90" .145" 362-S†2" 40 2.375" .154" 410 434 459-1


Pipe Size Sch. OD


3/4" 40 1.05 .113" 155†

1" 40 1.315" .133" 2121 1/4" 40 1.66" .140" 260 284 3091 1/2" 40 1.90" .145" 332 3562" 40 2.375" .154" 404


Pipe Size Sch. OD


3/4" 40 1.05" .113" 153†

1" 40 1.315" .133" 2061 1/4" 40 1.66" .140" 254 278 3031 1/2" 40 1.90" .145" 326 350 3752" 40 2.375" .154" 398

266 Steel 90° 1" IR

STEELALUMINUM 3003 Seamed Elbows 6063 Pipe ElbowsSTAINLESS STEEL Type 304

• Stainless Steel Type 316 and Brass Alloy C23000 are available upon request to [email protected].

ß Available with two untrimmed tangents. Add a B at the end of the number when ordering

Made in MILWAUKEE

1" Inside Radius Flush Weld Elbows

40 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914

Rr

Rr

Rr

Rr

Rr

Rr


STEELALUMINUM 3003 Seamed Elbows

6061 Tubing Elbows 6063 Pipe Elbows

STAINLESS STEEL Type 304 Type 316

• Brass Alloys C23000 and C27200; and Bronze C38500 are available upon request to [email protected].

Made in MILWAUKEE

1 5/8" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams – except as noted. 1.00" OD Tubing Elbows have an inside radius of 1.560".Elbows are supplied with a mill finish. They are available galvanized, zinc plated, anodized or polished to a satin or bright finish. All Elbows may also be purchased with tangents. Contact us with your requirements – [email protected] page 32 for optional Wedge-Lock™ Connectors. See page 38 for typical Wall Returns.See page 41 for issues relating to deformation in bent Elbows.

Seamed Elbows Mandrel Bent Elbows

35° Elbow Cut to order. Ship within 48 hours.These Elbows have no visible seam unless noted.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS3/4" 1.05" .113" 151-1 160-1 171-11" 1.315" .133" 4501 4515 4529

1.50" .120" 69001 1/4" 1.66" .140" 4431*1 1/4" 1.66" .140" 4431-S 4441 46511 1/2" 1.90" .145" 4461*1 1/2" 1.90" .145" 4461-S 4471 4681

35° Elbow with Two 2" TangentsThese Elbows have no visible seam.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.25" .065" 7883T

1" 1.315" .133" 45021.50" .120" 6901 6933

1 1/4" 1.66" .140" 4720 47251 1/2" 1.90" .145" 4730


Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.00" .083" 7802

3/4" 1.05" .113" 152-1 162-1 172-11" 1.315" .133" 4503 4517 4531

1.50" .120" 69021 1/4" 1.66" .140" 4432*1 1/4" 1.66" .145" 4432-S 4442 46521 1/2" 1.90" .140" 4462*1 1/2" 1.90" .145" 4462-S 4472 4682

45° Elbow with Two 2" TangentsThese Elbows have no visible seam.


3/4" 1.05" .113" 152-21" 1.315" .133" 4532

1.50" .120" 69351 1/4" 1.66" .140" 4721 47261 1/2" 1.90" .145" 4731



3/4" 1.05" .113" 153-1 163-1 173-11" 1.315" .133" 4505 4519 4533

1.50" .120" 69041 1/4" 1.66" .140" 4433*1 1/4" 1.66" .140" 4433-S 4443 46531 1/2" 1.90" .145" 4463*1 1/2" 1.90" .145" 4463-S 4473 4683

55° Elbow with Two 2" Tangents These Elbows have no visible seam.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 4506

1.50" .120" 69371 1/4" 1.66" .140" 47221 1/2" 1.90" .145" 4732 4737

Nominal Pipe Size OD

Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1.00" 1.56" 2.12" 4.24"

3/4" 1.05" 1.625" 2.15" 4.30"1.25" 1.625" 2.25" 4.50"

1" 1.315" 1.625" 2.282" 4.565"1.50" 1.625" 2.375" 4.75"

1 1/4" 1.66" 1.625" 2.455" 4.90"1 1/2" 1.90" 1.625" 2.575" 5.15"

* Denotes an Elbow with a seam.* Denotes an Elbow with a seam.

1 5/8" Inside Radius Flush Weld Elbows

shopwagner.com 41


Rr

Rr

Rr

Rr

Rr

Rr

C-C

see page 32

LOOK

FOR WAGNER’S

Wedge-Locks

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX


90° Elbow These Elbows have no visible seam unless noted.

Pipe Size OD

Wall Thick. STEEL

GALVANIZEDSTEEL ALUMINUM STAINLESS

1.00" .083" 7806 78381.00" .120" 7822

3/4" 1.05" .113" 154-1 164-1 174-11.25" .065" 7856 7888T1.25" .120" 7872

1" 1.315" .133" 4507 4521 45351.50" .120" 6906 6922 6938

1 1/4" 1.66" .140" 4434* G4434*1 1/4" 1.66" .140" 4434-S 4444 46541 1/2" 1.90" .145" 4464* G4464*1 1/2" 1.90" .145" 4464-S 4474 4684

90° Elbow with One 2" Tangent Cut to order. Ship within 48 hours.These Elbows have no visible seam.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.00" .083" 7807 7839

3/4" 1.05" .113" 155-7 165-1 175-11.25" .065" 7857 7889T1.25" .120" 7873

1" 1.315" .133" 4508 4522 45361.50" .120" 6907 6923 6939

1 1/4" 1.66" .140" 4635 4645 46551 1/2" 1.90" .145" 4665 4675 4685

90° Elbow with two 2" TangentsThese Elbows have no visible seam.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.00" .083" 7808 7840

3/4" 1.05" .113" 155-81.25" .065" 7858 7890T

1" 1.315" .133" 4509 45371.50" .120" 6908 6924 6940

1 1/4" 1.66" .140" 4723 4728 46561 1/2" 1.90" .145" 4733 4738 4686

125° Elbow Cut to order. Ship within 48 hours.These Elbows have no visible seam.


3/4" 1.05" .113" 156-7 166-1 176-11" 1.315" .133" 4510 4524 4538

1.50" .120" 69091 1/4" 1.66" .140" 4636 4646 46571 1/2" 1.90" .145" 4666 4676 4687

135° Elbow Cut to order. Ship within 48 hours. These Elbows have no visible seam.


3/4" 1.05" .113" 157-7 167-1 177-11" 1.315" .133" 4511 4525 4539

1.50" .120" 69101 1/4" 1.66" .140" 4637 4647 46581 1/2" 1.90" .145" 4667 4677 4688

Rr

145° Elbow Cut to order. Ship within 48 hours. These Elbows have no visible seam.


3/4" 1.05" .113" 158-1 168-1 178-11" 1.315" .133" 4512 4526 4540

1.50" .120" 69111 1/4" 1.66" .140" 4724 4729 46591 1/2" 1.90" .145" 4734 4739 4689

RrC-C

180° Elbow These Elbows have no visible seam.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.00" .083" 7812 78441.00" .120" 7828

3/4" 1.05" .113" 159-1 169-1 179-11" 1.315" .133" 4513 4527 4541

1.50" .120" 6912 6928 69441 1/4" 1.66" .140" 4638 4648 46601 1/2" 1.90" .145" 4668 4678 4690

180° Elbow with Two 2" Tangents These Elbows have no visible seam.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.00" .083" 7813ß 78451.00" .120" 7829

3/4" 1.05" .113" 159-2ß 169-2 179-21.25" .065" 7863ß

1.25" .120" 78791" 1.315" .133" 4514B 4528ß 4542ß

1.50" .120" 6913ß 6929ß 6945ß

1 1/4" 1.66" .140" 4639ß 4649ß 4661ß†

1 1/2" 1.90" .145" 4669ß 4679ß 4691ß

ß Available with two untrimmed tangents. Add a B at the end of the number when ordering.

† Available from stock in Type 316 alloy – order 4661B.316 – untrimmed

1 5/8" Inside Radius Flush Weld Elbows

42 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914


Rr R

r

Rr

Rr R

r

Rr



Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1" 1.315" 2.00" 2.675" 5.35"

1.50" 2.00" 2.75" 5.50"1.625" 2.00" 2.812" 5.624"

1 1/4" 1.66" 2.00" 2.83" 5.66"1.75" 2.00" 2.875" 5.75"

1 1/2" 1.90" 2.00" 2.95" 5.90"2.00" 2.00" 3.00" 6.00"

2" 2.375" 2.00" 3.188" 6.375"

2" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams – except as noted. Elbows are supplied with a mill finish. They are available galvanized, zinc plated, anodized or polished to a satin or bright finish. All Elbows may also be purchased with tangents. Contact us with your requirements – [email protected] page 32 for optional Wedge-Lock™ Connectors. See page 38 for typical Wall Returns.

35° Elbow with Two 2" TangentsPipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS

1.50" .065" 79331.50" .120" 7917 7933.120

1 1/4" 1.66" .140" 251-21 1/2" 1.90" .145" 323-2

2.00" .120" 7951 7967 7983

35° Elbow Cut to order. Ship within 48 hours.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 204* 2201" 1.315" .133" 204-S 252-S

1.50" .065" 79001.50" .120" 7900.120

1 1/4" 1.66" .140" 250*1 1/4" 1.66" .140" 250-S 274 2991 1/2" 1.90" .145" 322*1 1/2" 1.90" .145" 322-S 346 371

2.00" .120" 79502" 2.375" .134" 394* 408* 425*†


Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 208*1" 1.315" .133" 208-S 222 259-S

1.50" .120" 7902.1201 1/4" 1.66" .140" 256*1 1/4" 1.66" .140" 256-S 280 3051 1/2" 1.90" .145" 328*1 1/2" 1.90" .145" 328-S 352 377

2.00" .120" 79522" 2.375" .134" 396* 412-2* 427*†

45° Elbow with Two 2" TangentsPipe Size OD Wall Thick. STEEL ALUMINUM

1.50" .120" 7903.120 79191 1/4" 1.66" .140" 257-21 1/2" 1.90" .145" 329-2 353-2

2.00" .120" 7969

55° Elbow with Two 2" TangentsPipe Size OD Wall Thick. STEEL STAINLESS

1.50" .065" 79371 1/4" 1.66" .140" 263-21 1/2" 1.90" .145" 335-2

2.00" .120" 7955 7987


Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 210* 2261" 1.315" .133" 210-S 265-S

1.50" .065" 79041 1/4" 1.66" .140" 262*1 1/4" 1.66" .140" 262-S 286 3111 1/2" 1.90" .145" 334*1 1/2" 1.90" .145" 334-S 358 383

2.00" .120" 79542" 2.375" .134" 400* 414* 431*†

* Denotes an Elbow with a seam. † Denotes Sch. 10.

STEEL ALUMINUM 3003 Seamed Elbows 6061 Tubing Elbows 6063 Pipe Elbows STAINLESS STEEL Type 304• Stainless Steel Type 316; Brass Alloys C23000 and C27200;

and Bronze C38500 are available upon request to [email protected].

Made in MILWAUKEE


shopwagner.com 43

UpperPost

Elbow

Lower Post Elbow

12" min.

1 treadwidth

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

Wagner can also provide this bent from one section of Pipe or Tube. See templates on Page 196 and 197.

2010 ADA Standards for Accessible Design (ADASAD)The ADASAD has specific requirements regarding a Handrail. The detail below is a typical wall mount application. The Railing must extend 12" beyond the top tread nosing and a tread depth at the bottom of the stairs. For more information on these and other code requirements, refer to page 226.

Wagner can provide this type of Railing bent from one piece of pipe or tube with Wall Returns.

Optional Wedge- Lock™ Connectors for

Alignment and Decreased Grinding Time.

Refer to page 32.

Rr

90° ElbowPipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS

1" 1.315" .133" 214* 2281" 1.315" .133" 214-S 271-S

1.50" .065" 7906 79381.50" .120" 7906.120 7922 7938.120.4

1.625" .065" 7938T1.625" .120" 7906T

1 1/4" 1.66" .140" 268*1 1/4" 1.66" .140" 268-S 292 3171 1/2" 1.90" .145" 340*1 1/2" 1.90" .145" 340-S 364 389

2.00" .120" 7956 7972 79882" 2.375" .134" 402* 418* 433*†

Rr


1" 1.315" .133" 214-2 228-2 271-S21.50" .065" 7908 79401.50" .120" 7908.120 7924 7940.120

1.625" .065" 7940T1 1/4" 1.66" .140" 269-7 293-7 317-31 1/2" 1.90" .145" 341-7 365-7 389-3

2.00" .120" 7958 7974 7990

Rr


Pipe Size OD Wall Thick. STEEL ALUMINUM1.50" .065" 79091.50" .120" 7909.120

1 1/4" 1.66" .140" 269-4 293-41 1/2" 1.90" .145" 341-4 365-4

2.00" .120" 7959

Rr


Pipe Size OD Wall Thick. STEEL ALUMINUM1 1/4" 1.66" .140" 269-5 293-51 1/2" 1.90" .145" 341-5 365-5

RrC-C


Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1.50" .065" 79121.50" .120" 7912.120 7928 7944.120

1.625" .065" 7944T1 1/4" 1.66" .140" 269-2 293-21 1/2" 1.90" .145" 341-2 365-2

2.00" .120" 7962 7978 7994

Rr

C-C

180° Elbow with Two 2" TangentsPipe Size OD Wall STEEL ALUMINUM STAINLESS

1" 1.315" .133" 217ß 233ß 271-S31.50" .065" 7945ß

1.50" .120" 7929ß 7945.120ß

1 1/4" 1.66" .140" 269-6ß 293-6ß 317-21 1/2" 1.90" .145" 341-6ß 365-6ß 389-4ß

2.00" .120" 7963ß 7979ß 7995ß

Rr

90° Elbow with One 2" Tangent Cut to order. Ship within 48 hours.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 214-1 228-1

1.50" .065" 7907 79391.50" .120" 7907.120 7923 7939.120

1.625" .065" 7939T1 1/4" 1.66" .140" 269-3 293-3 317-11 1/2" 1.90" .145" 341-3 365-3 389-1

2.00" .120" 7957 7973 7989

Note: Upper Post Elbow Angle + Lower Post Elbow Angle = 180°


.4 Available from stock with a satin finish – order 7938.120.4.


44 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914

Rr

Rr

Rr

Rr

Rr

Rr

Rr

Rr

Rr

Rr

Rr

Rr

RrC-C

Rr

C-C


3" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams – except as noted.


1.50" .120" 6951 69721 1/4" 1.66" .140" 253-21 1/2" 1.90" .145" 349-22" 2.375" .154" 413


1.50" .120" 6953 69731 1/4" 1.66" .140" 259-21 1/2" 1.90" .145" 331-2 355-2


1" 1.315" .133" 507-2 517-2 527-21.50" .120" 6958 6969 6977

1 1/4" 1.66" .140" 271-7 295-7 464-21 1/2" 1.90" .145" 343-7 367-7 391-22" 2.375" .154" 424 446


Pipe Size OD Wall Thick. STEEL ALUMINUM1" 1.315" .133" 507-3

1.50" .120" 69591 1/4" 1.66" .140" 271-4 295-41 1/2" 1.90" .145" 343-4 367-42" 2.375" .154" 426 448



1.50" .120" 69601 1/4" 1.66" .140" 271-5 295-51 1/2" 1.90" .145" 343-5 367-52" 2.375" .154" 430 449



1.50" .120" 69611 1/4" 1.66" .140" 271-8 295-81 1/2" 1.90" .145" 343-82" 2.375" .154" 432 450



1.50" .120" 69521 1/4" 1.66" .140" 258*1 1/4" 1.66" .140" 258-S 282 4621 1/2" 1.90" .145" 330*1 1/2" 1.90" .145" 330-S 354 3792" 2.375" .154" 415 439 455†



1.50" .120" 69541 1/4" 1.66" .140" 264*1 1/4" 1.66" .140" 264-S 288 4631 1/2" 1.90" .145" 336*1 1/2" 1.90" .145" 336-S 360 3852" 2.375" .154" 419 442 457†


1" 1.315" .133" 507 517 5271.50" .120" 6956 6967 6975

1 1/4" 1.66" .140" 270* 294 4641 1/4" 1.66" .140" 270-S1 1/2" 1.90" .145" 342* 366 3911 1/2" 1.90" .145" 342-S2" 2.375" .154" 421 444 459-3†

90° Elbow with One 2" Tangent Cut to order.

Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 507-1 527-1

1.50" .120" 6957 6968 69761 1/4" 1.66" .140" 271-3 295-3 464-11 1/2" 1.90" .145" 343-3 367-3 391-12" 2.375" .154" 423 445 460†


1" 1.315" .133" 507-61.50" .120" 6962 6978

1 1/4" 1.66" .140" 271-2 295-2 464-61 1/2" 1.90" .145" 343-2 367-2 391-62" 2.375" .154" 435 451 469†


1" 1.315" .133" 509ß

1.50" .120" 6963ß 6971ß 6979ß

1 1/4" 1.66" .140" 271-6ß 295-6ß 464-7ß

1 1/2" 1.90" .145" 343-6ß 367-6ß 391-7ß

2" 2.375" .154" 436ß 452 470†

Nominal Pipe Size OD Inside Radius (r)

Center Line Radius (R)


Diam. (C-C)1" 1.315" 3.00" 3.675" 7.35"

1.50" 3.00" 3.75" 7.50"1 1/4" 1.66" 3.00" 3.83" 7.66"1 1/2" 1.90" 3.00" 3.95" 7.90"2" 1.75" 3.00" 4.188" 8.375"



1.50" .120" 69501 1/4" 1.66" .140" 252* 276 4611 1/2" 1.90" .145" 324*1 1/2" 1.90" .145" 324-S 348 3732" 2.375" .154" 412-3 437 453-3†

55° Elbow with Two 2" TangentsPipe Size OD Wall Thick. STEEL ALUMINUM

1.50" .120" 69551 1/4" 1.66" .140" 265-2 288-21 1/2" 1.90" .145" 337-22" 2.375" .154" 420


† Denotes Sch. 10. ß Available with two untrimmed tangents.


shopwagner.com 45

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

4" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams – except as noted. 1.50" Tube Elbows have a 4.25" inside radius.

Mandrel Bent Elbow Seamed Elbow


Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1" 1.315" 4.092" 4.75" 9.50"

1.50" 4.25" 5.00" 10.00"1 1/4" 1.66" 4.00" 4.83" 9.66"1 1/2" 1.90" 4.00" 4.95" 9.90"2" 2.375" 4.00" 5.188" 10.375"

Rr

45° Elbow with Two 2" TangentsPipe Size OD Wall Thick. STEEL

1 1/2" 1.90" .145" 5662-22" 2.375" .154" 5723

Rr


1.50" .120" 6955-51 1/4" 1.66" .140" 5633-31 1/2" 1.90" .145" 5663-3

Rr


Pipe Size OD Wall Thick. STEEL1 1/4" 1.66" .140" 56361 1/2" 1.90" .145" 5666

Rr


Pipe Size OD Wall Thick. STEEL1 1/4" 1.66" .140" 56371 1/2" 1.90" .145" 5667

Rr


Pipe Size OD Wall Thick. STEEL1 1/4" 1.66" .140" 5637-41 1/2" 1.90" .145" 5667-4

RrC-C


1" 1.315" .133" 5608 5618 56291.50" .120" 6962-5 6970-5 6978-5

1 1/4" 1.66" .140" 5638 5648 56571 1/2" 1.90" .145" 5668 5678 56882" 2.375" .154" 5732 5746 5760†

Rr


1 1/4" 1.66" .140" 5631-2

Rr


Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS1" 1.315" .133" 5605 5615 5625

1.50" .120" 6957-5 6968-5 6976-51 1/4" 1.66" .140" 5635 5645 56551 1/2" 1.90" .145" 5665 5675 56852" 2.375" .154" 5727 5741 5755†

Rr

90° Elbow Pipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS

1" 1.315" .133" 5604 5614 56241.50" .120" 6956-5 6967-5 6975-5

1 1/4" 1.66" .140" 5634* 5644 56541 1/2" 1.90" .145" 5664 5674 56842" 2.375" .154" 5726 5740 5754†

Rr


1" 1.315" .133" 5606 56171.50" .120" 6958-5 6969-5 6977-5

1 1/4" 1.66" .140" 5640 56501 1/2" 1.90" .145" 5670 5680 56902" 2.375" .154" 5728 5742 5756†

Rr

C-C

180° Elbow with Two 3" Tangents UntrimmedPipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS

1" 1.315" .133" 5609B 5619B 5630B1.50" .120" 6963-5B 6971-5B 6979-5B

1 1/4" 1.66" .140" 5639B 5649B 5658B1 1/2" 1.90" .145" 5669B 5679B 5689B2" 2.375" .154" 5733B 5747B 5761B†

Rr


Pipe Size OD Wall Thick. STEEL ALUMINUM1" 1.315" .133" 5601 5611

1.50" .120" 6950-51 1/4" 1.66" .140" 5631*1 1/2" 1.90" .145" 5661 56712" 2.375" .154" 5720 5734

Rr


Pipe Size OD Wall Thick. STEEL ALUMINUM1" 1.315" .133" 5602 5612

1.50" .120" 6952-51 1/4" 1.66" .140" 5632*1 1/2" 1.90" .145" 5662 56722" 2.375" .154" 5722 5736

Rr



1.50" .120" 6954-51 1/4" 1.66" .140" 5633*1 1/2" 1.90" .145" 5663 5673 56832" 2.375" .154" 5724 5738 5752†

STEEL ALUMINUM 3003, 6061; 6063 STAINLESS STEEL Type 304• Stainless Steel Type 316; Brass Alloys C23000 and C27200;


Made in MILWAUKEE

4" Inside Radius FLUSH WELD Elbows

46 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914


5" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams.Elbows are supplied with a mill finish. They are available galvanized, zinc plated, anodized or polished to a satin or bright finish. 1" Pipe and 1.50" Tube Elbows have a 5.25" inside radius.


Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1" 1.315" 5.25" 5.908" 11.815"

1.50" 5.25" 6.00" 12.00"1 1/4" 1.66" 5.00" 5.83" 11.66"1 1/2" 1.90" 5.00" 5.95" 11.90"2" 2.375" 5.00" 6.188" 12.375"

Rr


Pipe Size OD

Wall Thick. STEEL

1" 1.315" .133" 70101.50" .120" 6959-6

1 1/4" 1.66" .140" 70701 1/2" 1.90" .145" 71302" 2.375" .154" 7190

RrC-C

180° ElbowPipe Size OD


1" 1.315" .133" 70131.50" .120" 6962-6 6970-6 6978-6

1 1/4" 1.66" .140" 70731 1/2" 1.90" .145" 71332" 2.375" .154" 7193

Rr


Pipe Size OD


1" 1.315" .133" 7008 7028 70481.50" .120" 6957-6 6968-6 6976-6

1 1/4" 1.66" .140" 7068 7089 71081 1/2" 1.90" .145" 7128 7148 71682" 2.375" .154" 7188 7208 7228†

Rr

90° ELBOWPipe Size OD


1" 1.315" .133" 7007 7027 70471.50" .120" 6956-6 6967-6 6975-6

1 1/4" 1.66" .140" 7067 7088 71071 1/2" 1.90" .145" 7127 7147 71672" 2.375" .154" 7187 7207 7227†

Rr

90° Elbow with Two 2" TangentsPipe Size OD


1" 1.315" .133" 7009 70291.50" .120" 6958-6 6977-6

1 1/4" 1.66" .140" 7069 71091 1/2" 1.90" .145" 7129 7149 71692" 2.375" .154" 7189 7209

Rr

C-C

180° Elbow with Two 3" Tangents UntrimmedPipe Size OD


1" 1.315" .133" 7014B 7034B 7054B1.50" .120" 6963-6B 6971-6B 6979-6B

1 1/4" 1.66" .140" 7074B 7094B 7114B1 1/2" 1.90" .145" 7134B 7154B 7174B2" 2.375" .154" 7194B 7214B 7234B†

Mandrel Bent Elbow

Rr


Pipe Size OD


1" 1.315" .133" 7001 7021 70411.50" .120" 6950-6

1 1/4" 1.66" .140" 7061 7081 71011 1/2" 1.90" .145" 7121 7141 71612" 2.375" .154" 7181 7201 7221†

Rr


Pipe Size OD


1" 1.315" .133" 7003 7023 70431.50" .120" 6952-6

1 1/4" 1.66" .140" 7063 7083 71031 1/2" 1.90" .145" 7123 7143 71632" 2.375" .154" 7183 7202 7223†

Rr


Pipe Size OD


1" 1.315" .133" 7005 7025 70451.50" .120" 6954-6

1 1/4" 1.66" .140" 7065 7086 71051 1/2" 1.90" .145" 7125 7145 71652" 2.375" .154" 7185 7205 7225†

See page 47 for issues relating to deformation in Bent Elbows. * 4" Tangents. † Denotes Sch. 10.

STEEL ALUMINUM 6061 Tubing Elbows 6063 Pipe Elbows STAINLESS STEEL Type 304• Stainless Steel Type 316; Brass Alloys C23000 and C27200;


Made in MILWAUKEE


shopwagner.com 47


Rr

Rr

Rr

Rr

Elbows are supplied with a mill finish. They are also available galvanized, zinc plated, anodized or polished to a satin or bright finish.

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

6" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams. 1" Pipe Elbows have a 6.25" inside radius.


Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1" 1.315" 6.25" 6.908" 13.815"

1 1/4" 1.66" 6.00" 6.83" 13.66"1 1/2" 1.90" 6.00" 6.95" 13.90"2" 2.375" 6.00" 7.188" 14.375"

3 1/2" 4.00" 6.00" 8.00" 16.00"

Rr

Rr125° Elbow

Cut to order. Ship within 48 hrs.

Pipe Size OD Wall Thick. STEEL1" 1.315" .133" 7410

1 1/4" 1.66" .140" 74701 1/2" 1.90" .145" 75302" 2.375" .154" 7590

135° Elbow Cut to order. Ship within 48 hrs.


1 1/4" 1.66" .140" 74711 1/2" 1.90" .145" 75312" 2.375" .154" 7591

Rr

RrC-C145° Elbow

Cut to order. Ship within 48 hrs.


1 1/4" 1.66" .140" 74721 1/2" 1.90" .145" 75322" 2.375" .154" 7592

180° ElbowPipe Size OD Wall Thick. STEEL

1" 1.315" .133" 74131 1/4" 1.66" .140" 74731 1/2" 1.90" .145" 75332" 2.375" .154" 7593

Rr

C-C

180° Elbow with Two 3" Tangents UntrimmedPipe Size OD Wall Thick. STEEL ALUMINUM STAINLESS

1" 1.315" .133" 7414B 7434B 7454B1 1/4" 1.66" .140" 7474B 7494B 7514B1 1/2" 1.90" .145" 7534B 7554B 7574B2" 2.375" .154" 7594B 7614B

3 1/2" 4.00" .226" 91161B*



1 1/4" 1.66" .140" 7461 7481 75011 1/2" 1.90" .145" 7521 7541 75612" 2.375" .154" 7581 7601



1 1/4" 1.66" .140" 7463 7483 75031 1/2" 1.90" .145" 7523 7543 75632" 2.375" .154" 7583 7603



1 1/4" 1.66" .140" 7465 7485 75051 1/2" 1.90" .145" 7525 7545 75652" 2.375" .154" 7585 7605


1" 1.315" .133" 7407 7427 74471 1/4" 1.66" .140" 7467 7487 75071 1/2" 1.90" .145" 7527 7547 75672" 2.375" .154" 7587 7607

Rr



1 1/4" 1.66" .140" 7468 7488 75081 1/2" 1.90" .145" 7528 7548 75682" 2.375" .154" 7588 7608

Rr


1" 1.315" .133" 74091 1/4" 1.66" .140" 7469 7489 75091 1/2" 1.90" .145" 7529 75692" 2.375" .154" 7589 7609 7629†

3 1/2" 4.00" .226" 90160*

STEEL ALUMINUM 6063 STAINLESS STEEL Type 304Upon request to [email protected]: • Stainless Steel Type 316; Brass Alloys C23000 and C27200;

and Bronze C38500

Made in MILWAUKEE

Are You Working With Pipe or Tube?


48 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914

Rr

RrC-C

Rr

C-C



7" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams. 1" Pipe Elbows have a 7.30" inside radius.

Mandrel Bent Elbow

Bent Elbows


Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1" 1.315" 7.30" 7.957" 15.914"

1 1/4" 1.66" 7.00" 7.83" 15.66"1 1/2" 1.90" 7.00" 7.95" 15.90"



1" 1.315" .133" 85061 1/4" 1.66" .140" 8556 8570 85841 1/2" 1.90" .145" 8606 8620 8634


Wall Thick. STEEL

1" 1.315" .133" 85121 1/4" 1.66" .140" 85621 1/2" 1.90" .145" 8612



1" 1.315" .133" 8513B 8527B 8541B1 1/4" 1.66" .140" 8563B 8577B 8591B1 1/2" 1.90" .145" 8613B 8627B 8641B

Made in MILWAUKEE


and Bronze C38500

see page 32

LO

OK FO

R WAGNER’S

Wedge-Locks


shopwagner.com 49

Rr

Rr

RrC-C

Rr

C-C

Rr

Rr

Rr

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

Mandrel Bent Elbow

Stamped Elbows

8" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams. 1" Pipe Elbows have an 8.65" inside radius.See page 48 for issues relating to deformation in bent Elbows.


Pipe Size OD

Wall Thick. STEEL ALUMINUM

1" 1.315" .133" 76501 1/4" 1.66" .140" 7700 77141 1/2" 1.90" .145" 7750 77642" 2.375" .154" 8100 8114

2 1/2" 2.875" .203" 8142 8156


Inside Radius (r)

Center Line Radius

(R)


Diam. (C-C)1" 1.315" 8.65" 9.282" 18.565"

1 1/4" 1.66" 8.00" 8.83" 17.66"1 1/2" 1.90" 8.00" 8.95" 17.90"2" 2.375" 8.00" 9.188" 18.375"

2 1/2" 2.875" 8.00" 9.438" 18.875"


Pipe Size OD


1" 1.315" .133" 76521 1/4" 1.66" .140" 7702 77161 1/2" 1.90" .145" 7752 77662" 2.375" .154" 8102 8116

2 1/2" 2.875" .203" 8144 8158


Wall Thick. STEEL

1" 1.315" .133" 76621 1/4" 1.66" .140" 77121 1/2" 1.90" .145" 77622" 2.375" .154" 8112

180° Elbow with Two 3" Tangents Untrimmed

Pipe Size OD


1" 1.315" .133" 7663B1 1/4" 1.66" .140" 7713B 7727B 7741B1 1/2" 1.90" .145" 7763B 7777B 7791B2" 2.375" .154" 8113B 8127B

2 1/2" 2.875" .203" 8155B 8169B

145° Elbow Cut to order. Ship within 48 hrs.

Pipe Size OD

Wall Thick. STEEL

1" 1.315" .133" 76611 1/4" 1.66" .140" 77111 1/2" 1.90" .145" 77612" 2.375" .154" 8111

2 1/2" 2.875" .203" 8153


Wall Thick. STEEL

1" 1.315" .133" 76581 1/4" 1.66" .140" 77081 1/2" 1.90" .145" 77582" 2.375" .154" 8108

2 1/2" 2.875" .203" 8150



1" 1.315" .133" 76561 1/4" 1.66" .140" 7706 7720 77341 1/2" 1.90" .145" 7756 7770 77842" 2.375" .154" 8106 8120

2 1/2" 2.875" .203" 8148 8162

Made in MILWAUKEE


and Bronze C38500



50 ISO 9001:2008 F 414 214 0450 • P 414 214 0444 • T 888 243 6914

Rr

C-C

Rr

Rr

Rr

C-C


Made in MILWAUKEE

180° Elbow with Two 3" Tangents Untrimmed

Pipe Size OD


1 1/4" 1.66" .140" 8263B 8277B 8291B1 1/2" 1.90" .145" 8313B 8327B 8341B2" 2.375" .154" 8363B 8377B 8391B†

10" Inside Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams.

12" Center Line Radius Flush Weld ElbowsThese Elbows are precision mandrel bent parts – without seams.




Diam. (C-C)1" 1.315" 10.30" 10.958" 21.915"

1 1/4" 1.66" 10.00" 10.83" 21.66"1 1/2" 1.90" 10.00" 10.95" 21.90"2" 2.375" 10.00" 11.188" 22.375"




Diam. (C-C)1 1/4" 1.66" 11.170" 12.00" 24.00"1 1/2" 1.90" 11.05" 12.00" 24.00"2" 2.375" 10.812" 12.00" 24.00"

2 1/2" 2.875" 10.562" 12.00" 24.00"

RrC-C


Wall Thick. STEEL

1 1/4" 1.66" .140" 92621 1/2" 1.90" .145" 93122" 2.375" .154" 9362

RrC-C


Wall Thick. STEEL

1 1/4" 1.66" .140" 82621 1/2" 1.90" .145" 83122" 2.375" .154" 8362


Pipe Size OD


1 1/4" 1.66" .140" 8252 8266 82801 1/2" 1.90" .145" 8302 8316 83302" 2.375" .154" 8352 8380†

Rr



1 1/2" 1.90" .145" 93222" 2.375" .154" 9358 9372

Rr



1 1/4" 1.66" .140" 8258 8272 82861 1/2" 1.90" .145" 8308 8322

Rr


WallThick. STEEL ALUMINUM STAINLESS

1 1/4" 1.66" .140" 8256 8270 82841 1/2" 1.90" .145" 8306 8320 83342" 2.375" .154" 8356 8370 8384†



1 1/4" 1.66" .140" 9256 9270 92841 1/2" 1.90" .145" 9306 93202" 2.375" .154" 9356 9370 9384†



1 1/4" 1.66" .140" 9263B 9277B 9291B1 1/2" 1.90" .145" 9313B 9327B 9341B2" 2.375" .154" 9363B 9377B 9391B†

2 1/2" 2.875" .203" 9463B 9477B 9491B

10" and 12" Inside Radius Flush Weld ElbowsAll Elbows may be also be purchased with tangents. Contact Wagner with your requirements - [email protected] page 48 for issues relating to deformation in bent Elbows.

STEEL ALUMINUM 6063 STAINLESS STEEL Type 304


Optional Wedge- Lock™ Connectors for

Alignment and Decreased Grinding Time.

Refer to page 32.

† Denotes Sch. 10.

10" and 12" Inside Radius Flush Weld Elbows

shopwagner.com 51

Rr

Rr

Rr

Rr

C-C

Deformity Issues with Stock BendsThe process of bending Pipe and Tube results in unavoidable deformation.In Square and Rectangular Tube sections, the Tube will tend towards a trapezoidal deformation. The deformation may be as much as -5% on the inside of the bend and +5% on the outside of the bend.This may be avoided by ordering Elbows with Tangents since the tangent sections will be unaffected by the bending process.

Rr

STAN

DARD

PRO

DUCT

SRA

ILIN

G SY

STEM

STR

ADIT

IONA

L RA

ILIN

GCU

STOM

SER

VICE

SAP

PEND

IX

Made in MILWAUKEE

Square Tube Flush Weld ElbowsStock Square Tubing Elbows have a .083" wall Tubing except as noted. Contact Wagner regarding availability of other radii and thicknesses – .065" to .125" wall – [email protected].

r = Inside RadiusR = Center Line RadiusC-C = Center to Center Diameter


Square Tube r R STEEL

1.25" 3 1/8" 3 3/4" 63321.50" 3 3/4" 4 1/2" 63622.00" 7" 8" 6382†


Square Tube r R STEEL

1.50" 3 3/4" 4 1/2" 63602.00" 7" 8" 6380†

Square Tube Flush Weld Corner No Miter – No Sharp CornersThis cost-cutting corner simplifies fit-up and shortens fabrication. Simply square cut your Tubing.Radius equals the tube size. Not recommended for Square Corner Extruded Tube.

Square Tube

Wall Thick. STEEL

ALLOY 304STAINLESS

1.00" .080" 9210 92121.25" .080" 9215 92171.50" .080" 9220 92222.00" .080" 9225 92274.00" .104" 3900136B

90° Elbow with Two 2" TangentsSquare

Tube r R STEEL ALUMINUM1.00" 2 1/2" 3" 6308 64081.25" 3 1/8" 3 3/4" 63381.50" 3 3/4" 4 1/2" 63682.00" 7" 8" 6388†

180° Elbow with Two 2" Tangents Square

Tube r R C-C STEEL ALUMINUM1.00" 2 1/2" 3" 6" 6313ß 64131.25" 3 1/8" 3 3/4" 7 1/2" 6343ß

1.50" 3 3/4" 4 1/2" 9" 6373ß

2.00" 7" 8" 16" 6393†ß

90° ElbowSquare

Tube r R STEEL1.00" 2 1/2" 3" 63061.25" 3 1/8" 3 3/4" 63361.50" 3 3/4" 4 1/2" 63662.00" 7" 8" 6386†

STEEL A53, A500ALUMINUM 6063 Upon request:STAINLESS STEEL Type 304


† Denotes .120" wall.

Square Tube Flush Weld Elbows


Standard Products - Wagner

Documents

Transcript of Standard Products - Wagner