Standalone TCSM3i ETIP1-A Implementation for IPPWE (S12-14 TCSM HW)-Ver-1_0

DN09142374 Standalone TCSM3i ETIP1-A implementation for IP/PWE (S12 S14 TCSM HW)Copyright 2013 Nokia Solutions and Networks. All rights reserved.CONFIDENTIALAPPROVED 1.0

1 (127)

Standalone TCSM3iETIP1-A implementationfor IP/PWE (S12 - S14TCSM HW)Release Delivery: HW UpgradeProduct Family: Radio ControllersProduct: BSC3i 1000/2000, UpgradedFlexi BSCRelease: S16 onwards

Nokia Solutions and Networks is continually striving to reduce the adverse environmental effects of itsproducts and services. We would like to encourage you as our customers and users to join us inworking towards a cleaner, safer environment. Please recycle product packaging and follow therecommendations for power use and proper disposal of our products and their components.

If you should have questions regarding our Environmental Policy or any of the environmental serviceswe offer, please contact us at Nokia Solutions and Networks for additional information.


2 (127)

Table of Contents1 Purpose .................................................................................................................................................. 52 Scope of applications .............................................................................................................................. 63 Using the document ................................................................................................................................ 7

3.1 General info ....................................................................................................................................................... 74 Introduction ............................................................................................................................................. 8

4.1 Standalone TCSM3i equipment after upgrade ................................................................................................... 104.1.1 Ater interface ETIP with full HW redundancy ............................................................................... 104.1.2 A interface ETIP with full HW redundancy ................................................................................... 104.1.3 A interface ETIP Mixed configurations ......................................................................................... 11

5 Pre-requirements .................................................................................................................................. 135.1 Pre-requirements & Actions needed prior upgrade ............................................................................................ 135.2 Restrictions ..................................................................................................................................................... 135.3 Needed documentation .................................................................................................................................... 135.4 Needed equipment .......................................................................................................................................... 14

6 Fallback copying of the current package ................................................................................................ 157 BSC configuration printout (pre-check) .................................................................................................. 168 Licence installation and feature activation .............................................................................................. 179 Configuration example of Ater interface used in this instruction .............................................................. 1810 Master units in TCSM site ..................................................................................................................... 1911 TCSA rack cartridge position info .......................................................................................................... 2012 Ater interface ETIP1-A implementation for IP/PWE in Standalone TCSM ............................................... 21

12.1 Ater plug-in unit installation to BSC ................................................................................................................... 2112.1.1 When ETIP1-A PIU is used in BSC site to be connected to TCSM ETIP ....................................... 2112.1.2 When ET16 or ETS2 PIU is used in BSC site to be connected to TCSM ETIP viaEthernet over E1/T1 converter .................................................................................................................... 24

12.2 TC2C 0 and 1 .................................................................................................................................................. 2512.2.1 Move traffic from TC2C 0 and 1 cartridges .................................................................................. 2512.2.2 Delete A-interface configuration .................................................................................................. 2512.2.3 Delete TCSM/ET16/TR3/CLS from TC2C 0 and 1 cartridges ....................................................... 2612.2.4 Make cabling changes ................................................................................................................ 2612.2.5 Replace ET16 PIUs with ETIP1-A plug-in unit ............................................................................. 2812.2.6 Create first 4 TCSM units and plug-in units under TC2C-0 ........................................................... 2812.2.7 Create rest of the TCSM units to TC2C-0 and 1 .......................................................................... 3212.2.8 Create IP/PW locally to the Ater master and redundant ETIP1-A units.......................................... 3312.2.9 Add Tunnel and PW configuration of ETIP master unit for ETIP master TCSM unit inTC2C-0 track 3 ........................................................................................................................................... 3512.2.10 Create new PSN tunnel (or use the one created to Ater master) .................................................. 3612.2.11 Move traffic back to TC2C 0 and 1 cartridge ................................................................................ 39

12.3 TC2C 2 (optional) ............................................................................................................................................ 4112.3.1 Move traffic from TC2C 2 cartridge ............................................................................................. 4112.3.2 Delete A-interface configuration .................................................................................................. 4112.3.3 Delete TCSM/ET16/TR3 from TC2C 2 cartridge .......................................................................... 4212.3.4 Make cabling changes ................................................................................................................ 4212.3.5 Remove ET16 PIUs .................................................................................................................... 4312.3.6 Create the TCSM units to TC2C-2 .............................................................................................. 4312.3.7 Create IP/PW ............................................................................................................................. 4412.3.8 Move traffic back to TC2C 2 cartridge ......................................................................................... 46

12.4 TC2C 3 (optional) ............................................................................................................................................ 4812.4.1 Move traffic from TC2C 3 cartridge ............................................................................................. 4812.4.2 Delete A-interface configuration .................................................................................................. 4812.4.3 Delete TCSM/ET16/TR3 from TC2C 3 cartridge .......................................................................... 4912.4.4 Make cabling changes ................................................................................................................ 4912.4.5 Remove ET16 PIUs .................................................................................................................... 50


3 (127)

12.4.6 Create the TCSM units to TC2C-3 .............................................................................................. 5012.4.7 Create IP/PW ............................................................................................................................. 5112.4.8 Move traffic back to TC2C 3 cartridge ......................................................................................... 53



13 A-interface ETIP1-A implementation for IP/PWE in Standalone TCSM ................................................... 6813.1 Option1: Mixed configuration with transmission redundancy ETC-0 ETIP1-A, ETC-1 and ETC-2 ET16 ............... 68

13.1.1 Move traffic from ETC-0 TCSM(s) ............................................................................................... 6813.1.2 Delete ET16 PIU(s) from ETC-0 cartridge ................................................................................... 6913.1.3 Remove cables .......................................................................................................................... 6913.1.4 Remove sync cables in case connected to ETC-0 tracks ............................................................. 7113.1.5 Move and re-connect cables ....................................................................................................... 7113.1.6 Install ADMOD07 to ETC-0 track 7 .............................................................................................. 7213.1.7 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 7213.1.8 Synchronization usage with ETIP ................................................................................................ 7213.1.9 Create A-interface ETIP1-A plug-in unit to needed TR3 units ....................................................... 7213.1.10 Create IP/PW first to the TC2C-0 track 4 ETIP master locally ....................................................... 7313.1.11 Create new PSN tunnel (or use the one created to A-interface master) ........................................ 7513.1.12 Move traffic back to ETC-0 TCSM(s) ........................................................................................... 78

13.2 Option2: Mixed configuration with ETIP HW redundancy so that ETC-0 track 7 contains ETIP1-A, ETC-1 track 6 contains ETIP1-A, other tracks in ETC-1 and ETC-2 contains ET16 ................................................................ 79

13.2.1 Move traffic from ETC TCSM(s) .................................................................................................. 7913.2.2 Delete ET16 PIU(s) from ETC cartridges ..................................................................................... 7913.2.3 Remove cables .......................................................................................................................... 7913.2.4 Remove sync cables in case connected to ETC-0 and 1 tracks .................................................... 8113.2.5 Add modules and new cables ..................................................................................................... 8213.2.6 Move and re-connect cables ....................................................................................................... 8213.2.7 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 8313.2.8 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................... 8313.2.9 Create IP/PW locally to the A-interface master and redundant ETIP1-A units ............................... 8313.2.10 Add Tunnel and PW configuration of first A-interface ETIP master unit (ETC-0 in track 7) ............. 8613.2.11 Create new PSN tunnel (or use the one created to A-interface master) ........................................ 8713.2.12 Move traffic back to ETC-0 TCSM(s) ........................................................................................... 89

13.3 Option3: ETIP with HW redundancy ................................................................................................................. 9013.3.1 Move traffic from ETC TCSM(s) .................................................................................................. 9013.3.2 Delete ET16 PIU(s) from ETC cartridges ..................................................................................... 9013.3.3 Remove cables .......................................................................................................................... 9013.3.4 Remove sync cables in case connected to ETC-0 and 1 tracks .................................................... 9213.3.5 Add modules and new cables ..................................................................................................... 9213.3.6 Move and re-connect cables ....................................................................................................... 9313.3.7 Replace ET16 PIU(s) with ETIP1-A plug-in unit ........................................................................... 9313.3.8 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................... 94


4 (127)

13.3.9 Create IP/PW locally to the A-interface master and redundant ETIP1-A units ............................... 9413.3.10 Add Tunnel and PW configuration of first A-interface ETIP master unit ( ETC-0 in track 7) ............ 9713.3.11 Create new PSN tunnel (or use the one created to A-interface master) ........................................ 9813.3.12 Move traffic back to ETC-0 TCSM(s) ......................................................................................... 10013.3.13 Move traffic from ETC-1 TCSM(s) ............................................................................................. 10113.3.14 Delete ET16 PIU(s) from ETC cartridges ................................................................................... 10113.3.15 Remove cables ........................................................................................................................ 10113.3.16 Add modules and new cables ................................................................................................... 10313.3.17 Move and re-connect cables ..................................................................................................... 10313.3.18 Replace ET16 PIU(s) with ETIP1-A plug-in unit ......................................................................... 10413.3.19 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................. 10413.3.20 Create IP/PW locally to the A-interface master and redundant ETIP1-A units ............................. 10513.3.21 Add Tunnel and PW configuration of first A-interface ETIP master unit (ETC-1 in track 7) ........... 10713.3.22 Create new PSN tunnel (or use the one created to A-interface master) ...................................... 10813.3.23 Move traffic back to ETC-1 TCSM(s) ......................................................................................... 11113.3.24 Move traffic from ETC-2 TCSM(s) ............................................................................................. 11113.3.25 Delete ET16 PIU(s) from ETC cartridges ................................................................................... 11113.3.26 Remove cables ........................................................................................................................ 11113.3.27 Add modules and new cables ................................................................................................... 11313.3.28 Move and re-connect cables ..................................................................................................... 11313.3.29 Replace ET16 PIU(s) with ETIP1-A plug-in unit ......................................................................... 11413.3.30 Create TCSM(s) and ETIP1-A plug-in unit ................................................................................. 11413.3.31 Create IP/PW locally to the A-interface master and redundant ETIP1-A units ............................. 11513.3.32 Add Tunnel and PW configuration of first A-interface ETIP master unit (ETC-2 in track 7) ........... 11713.3.33 Create new PSN tunnel (or use the one created to A-interface master) ...................................... 11813.3.34 Move traffic back to ETC-2 TCSM(s) ......................................................................................... 121

14 Actions after upgrade & Post conditions .............................................................................................. 12214.1 BSS Integration ............................................................................................................................................. 12214.2 BSC configuration printout (post-check) .......................................................................................................... 12214.3 Return to the old HW configuration ................................................................................................................. 122

15 Appendix 2: Internal PCM usage for Ater interface ............................................................................... 12316 Appendix 2: Internal PCM usage for A-interface .................................................................................. 12417 Appendix 3: Updating embedded software of ETIP1-A ......................................................................... 125

Contact:

Contact your local Nokia Solutions and Networks support

Summary of changes:

1.0-0 1st approved version


5 (127)

1 PURPOSE

This document describes the implementation of changing ET16 plug-in unit in standalonen TCSM3i to ETIP1-Aline/equipment protection.The ETIP1-A line/equipment protection implementation is available for third generation DX200 standaloneTCSM3i.


6 (127)

2 SCOPE OF APPLICATIONS

Standalone TCSM3i ETIP1-A implementation for IP/PWE (S12 - S14 TCSM HW) isavailable for third generation DX200 TCSM3i in S16 release level onwards.

The procedure cannot be executed without traffic interruption. Traffic must be movedfrom concerning ET16/TR3 plug-in unit before the actual upgrade.

Procedure must be performed locally at BSC/TCSM3i site.


7 (127)

3 USING THE DOCUMENT

3.1 General info

Standalone TCSM3i ETIP1-A implementation for IP/PWE (S12 - S14 TCSM HW) is done manually without theHIT macro.


8 (127)

4 INTRODUCTION

Standalone TCSM3i ETIP1-A implementation for IP/PWE (S12 - S14 TCSM HW) procedure consists of thefollowing tasks:

- Fallback copying of the current software

- BSC configuration printout (pre-check)

- Licence installation and feature activation

- Ater interface ETIP1-A implementation for IP/PWE in Standalone TCSM

- A-interface ETIP1-A implementation for IP/PWE in Standalone TCSM

- Actions after upgrade and post conditions

o BSS Integration

o BSC configuration printout (post-check)

Fallback copying, BSC configuration printout tasks can be executed during daytime.Actual upgrade is recommended to be executed during night-time. This procedure can be done to standaloneTCSM3i.For standalone TCSM3i part, the procedure is divided for A- and Ater-interfaces. For Ater-interface only HWredundancy option is possible. A-interface contains more options: transmission redundancy, HW redundancy andmixed configuration.In case when old configuration needs to be removed, the traffic must be moved, interface(s) removed becausethe plug-in unit needs to be deleted from equipment database. After successful upgrade and interfaces has beencreated back, the traffic can be moved back.The estimated time for HW upgrade depends on the configuration.The upgrade cannot be executed with traffic and traffic needs to be re-hosted. During upgrade effected unit(s) willbe blocked and state changed to TE-EX or SE-NH.

With this procedure following possibility is to be added:

- In Standalone TCSM3i Ater- interface part, replace ET16 with ETIP plug-in unit withhardware redundancy

- In Standalone TCSM3i A- interface part, replace ET16 with ETIP plug-in unit withline or hardware redundancy and also mixed configuration option is possible.

Background:ETIP1-A plug-in unit is a unit, which implements IETF pseudo wire emulation edge to edge (PWE3) functionalityin DX 200. Basically this means E1/T1 over Ethernet. The ETIP1-A plug-in unit has one redundant Gigabitethernet interface in front panel.The Gigabit ethernet interfaces are provided by hot-pluggable SFP modules, which are not part of the ETIP1-APIUs structure.


9 (127)

As a GSW interface the unit uses either thirty-two 8 Mbit/s TDM interfaces or two Hotlink interfaces. There areactually four physical Hotlink interfaces, due to 2N redundancy support.ETIP1 can be installed into dedicated TC2C-A, GT4C-A and GT6C-A cartridges. ETIP1 supports alsosynchronous ethernet and timing over packet (IEEE1588v2) for synchronization purposes.

ETIP in TCSM3i: Can be connected to max 24 BSC3is Can have one ETIP1-A pair in ATER interface and max three ETIP1-As in A

interface. Ater ETIP must be HW redundant, but A interface can be line redundant. Ater ETIP capacity is 96 PCMs and A ETIP capacity is 128 PCMs. Internal PCM numbering starting from 0. Not same order as physical TR3E/A

cards in cabinet!


10 (127)

4.1 Standalone TCSM3i equipment after upgrade

4.1.1 Ater interface ETIP with full HW redundancy

Configuration after HW upgrade in case of HW redundancy:

TC2C 0 & 1 cartridges. ETIP1-A used as Ater interfaces. Optional PIUs turquoise/dark.

4.1.2 A interface ETIP with full HW redundancy

Congifuration after HW upgrade in case of HW redundancy:

2 4 5 6 73 8 9 101 11 12 13 14 15 16 17 18 19

A. TC2C 0

J6

OPR

J7

SHIM

4T

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

SHIM

4T

TR3T

Wor

king

Ate

rETI

P

OPR

ETIP

1

2 4 5 6 73 8 9 101 11 12 13 14 15 16 17 18 19

B. TC2C 1

J6

OPR

J7

SHIM

4T

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

J6

OPR

J7

SHIM

4TOPR

ETIP

1

1. ETIP1-A used as Ater interfaces

Prot

ectin

gAt

erET

IP

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T

TR3T


11 (127)

ETC 0 & 1 & 2 cartridges. Only ETIP1-As used as A-interfaces. OptionalPIUs turquoise/dark.

4.1.3 A interface ETIP Mixed configurations

Mixed configuration with transmission redundancy and Mixed configuration ETIP HW redundancy:

Equipped onlywith HWredundancy

02 03 04 05 0601 07 08 09

D. ETC 1

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

02 03 04 05 0601 07 08 09

C. ETC 0

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

O PR

ETIP

1

OPR

ETIP

1

O PR

ETIP

1

OPR

ETIP

1

OP R

ETIP

1

2. ETIP1-A used as A-interfaces


Wor

king

A-in

tf.ET

IP

Prot

ectin

gA

-intf.

ETIP

Wor

king

A-in

tf.ET

IP

Prot

ectin

gA

-intf.

ETIP

Prot

ectin

gA

-intf.

ETIP


12 (127)

ETC 0 & 1 & 2 cartridges. Configuration examples of mixed ET16 & ETIP1-A used as A-interfaces. Optional PIUsturquoise/dark.

3. Mixed configuration example 16*ET16 & 1*ETIP1-A used as A-interfaces, ETIP Transmission protection used


02 03 04 05 0601 07 08 09

G. ETC 1

SHIM

4T

02 03 04 05 0601 07 08 09

F. ETC 0SH

IM4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4TO PR

ETIP

1W

orki

ngA

-intf.

ETIP

Prot

ectin

gA

-intf.

ETIP

SHIM

4T

SHIM

4T 0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

02 03 04 05 0601 07 08 09

G. ETC 1SH

IM4T

02 03 04 05 0601 07 08 09

F. ETC 0

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

SHIM

4T

O PR

ETIP

1W

orki

ngA

-intf.

ETIP

SHIM

4T

SHIM

4T 0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

0123456789101112131415

ET16

4. Mixed configuration example 15*ET16 & 1*ETIP1-A pair used as A-interfaces, ETIP HW protection used

OPR

ETIP

1

SHIM

4TSH

IM4T


13 (127)

5 PRE-REQUIREMENTS

5.1 Pre-requirements & Actions needed prior upgrade

The procedure can be implemented only forS16 software onwards. It is recommended to install all availablechange deliveries prior to the upgrade.SW licence 1380 (Integrated IP Card) is needed to be installed before actual upgrade can be started.

In case of Standalone TCSM3i part, the related ET16/ETS2 plug-in unit in BSC side, needs to be upgradedbefore TCSM3i upgrade can be started.

IMPORTANT!Re-direct traffic from upgraded TCSA cabinet. Each ETIP unit must be handled case by case and PCMareas which are affected during upgrade may vary. In case upgrade causes disturbances to some otherunit, the traffic needs to be re-directed, interfaces removed and unit needs to be deleted (PCM areasreleased to new ETIP unit usage) from hardware database before new configuration is created.

BSS Split tool offers automated process to support BSC renewal. This is extremely useful, when older BSC(s) aremodernised to BSC3i(s). This process includes the automation of labor-intensive re-hosting of BTS to new BSC(s)including data and parameter updates to name a few. The downtime of operational BTS(s) is this way minimisedduring re-homing. If re-homing speed is the key driver, more than 100 sites can be moved to the new BSC duringone night by using .XML files for data transfer between the BSC(s) assisted by CM tools (CM Plan Manager, CMEditor and CM Analyser). Further information about BSS Split tools is available from Nokia OSS / NetActrepresentatives.

5.2 Restrictions

In Standalone TCSM3i Ater interface part:TC2C-0 and TC2C-1 cartridges are required to be upgrade. After that the other TC2C-cartridge upgrades areoptional.

During upgrade, the unit will be blocked, meaning that the interfaces which controlling unit is upgradedwill be affected. After the upgrade has been finished successfully for one ETIP unit (in case of HWredundancy ETIP unit pair) the traffic can be re-directed back.

5.3 Needed documentation

To perform the upgrade successfully, the following documentation is required: Standalone TCSM3i ETIP1-A implementation for IP/PWE (S12 - S14 TCSM

HW) (this document) Plug-in unit software upgrade procedure Cabling Instructions for TCSM3i (NED)


14 (127)

Equipment list for TCSM3i (NED) PWT User Guide (NED) Pre-Processor Program Information Fallback copying instructions of DX200 BSC (NED) Technical Support Note: Minimum HW Requirements for BSC S1xx Release HIT Users manual Cabling Instructions for i-series Network Elements

5.4 Needed equipment

To perform the upgrade successfully, the following HW are required:In case of Standalone TCSM3i Ater interface: General Set for ETIP1-A usedas Ater Interface in Standalone TCSM3i installation (S15) and Cabinet upgradeset, ETIP1-A redundancy pair specific for Standalone TCSM3i installation(S15).

In case of Standalone TCSM3i A interface: Cabinet upgrade set, ETIP1-Aredundancy pair specific for Standalone TCSM3i installation (S15). Note! Forfull HW rendundancy upgrade, three above hardware kit are needed.

Needed amount of ETIP plug-in units.

The status of the current BSC software package is checked. Note that the current software package must be withstatus BU before the actual upgrade can be started. The software status is to be checked with command:

ZWQO:RUN;

Check from the output that all the computer units which are currently in use are running on correct softwarepackage with the status BU. If the software package status is FB or NW, find out the cause for the setting.

The status can be changed to BU with command:

ZWSC:STAT=NW:STAT=BU;

The active and blocked alarms (DX200 and BTS alarms) can be printed out with following commands:

ZAHO;

ZABO;

ZEOL;

ZEOE;


15 (127)

6 FALLBACK COPYING OF THE CURRENT PACKAGE

A fallback copying of the running software package must be made before the upgrade.A fallback copying from the old SW can be made by running macro step Fallback copying of the currentpackage.Manually, the fallback copying can be made following the document: Fallback copying in BSC. The documentcan be found from NED.


16 (127)

7 BSC CONFIGURATION PRINTOUT (PRE-CHECK)

The information about the BSC configurations and conditions are collected.Precondition checking is recommended to do during the daytime before the actual upgrade will be started. Thechecking can be made by using the macro (UPGMAIN.HIT) or manually following the instructions from BSCconfiguration printout-document delivered in Release Binder.For macro execution, choose the BSC configuration printout (pre) step in BSC/TCSM ETIP1-A implementation forIP/PWE procedure. Follow then the macro execution according the BSC configuration printout document.


17 (127)

8 LICENCE INSTALLATION AND FEATURE ACTIVATION

SW licence 1380 (Integrated IP Card) is needed to be installed before actual upgrade can be started.Macro checks the licence status and if licence is not installed properly the licence needs to be installed manuallyaccording to following instructions.

Licence state can be printed with following command:ZW7I:FEA,FULL:FSTATE=ON,FEA=1380;

FlexiBSC KOLI 542257 2010-04-15 14:13:13

FEATURE INFORMATION:

---------------------------------------------- FEATURE CODE:..............1380

FEATURE NAME:..............ETIPFEATURE STATE:.............ONFEATURE CAPACITY:..........25

COMMAND EXECUTEDIf licence state is OFF, change the state to ON with following command:ZW7M:FEA=1380:ON:;

If licence is not installed, install the new licence file with the command:ZW7L::ON;More information of licences in the BSC can be found in NED.


18 (127)

9 CONFIGURATION EXAMPLE OF ATER INTERFACE USED IN THISINSTRUCTION

Here is the example configuration used in these instructions for Standalone TCSM3i Ater interface.In Thisexample the BSC and TCSM has ETIP1-A card created and connection via Cisco router. In this document inexample the TCSM ETIP1-A in Ater interface is connected via cisco router to BSC ETIP1-A card

HSRP:VLAN150 10.16.65.161VLAN151 10.16.65.169VLAN152 10.16.65.177VLAN153 10.16.65.185

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.169GW

10.16.65.172/29VLAN151

PW0ETIP,2

10.16.65.161GW

10.16.65.164/29VLAN150

PWMANA0ETIP,2

KOLIFlexiBSC

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.181/29VLAN152

PWMANA0ETIP,1

TCSM3i

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.181/29VLAN152

PWMANA0ETIP,1

TCSM3i

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.180/29VLAN152

PWMANA0ETIP,1

TCSM3i

10.16.65.185GW

10.16.65.188/29VLAN153

PW0ETIP,1

10.16.65.177GW

10.16.65.180/29VLAN152

PWMANA0ETIP,1

TCSM3i

ETIP connectionKOLI TCSM3i

ETIP connectionKOLI TCSM3i

Cisco SITE1_0

Cisco SITE1_1

Gi1/0/17

Gi1/0/17

Gi1/0/18

Gi1/0/18

EET4

EET5

Transmission protected Hardware protected

KOLIKOLI TCSM3iTCSM3i


19 (127)

10 MASTER UNITS IN TCSM SITE

Masters Info TR3A/E & TR3T PIU Tracknumbers

Cartridge

Cabinet Headmaster Cabinet headmaster supervises the clock unit of thecabinet and collects wired alarms from other cartridgesof the cabinet.

2 TC2C-0

Ater ET16 Master(Cartridge master)

This PIU controls Ater interface ET16 unitsNote!When a TC2C cartridge is shared between two BSCs,the TR3A/E or TR3T PIU in track 9 is also acting as acartridge master.Also O&M master for A-interface

1 ( and 9) All TC2C's

A ET16 Master O&M master for A-interface 5, 9, 13 All TC2C's

Ater ETIP1-A master O&M master for Ater-InterfaceNote!ETIP1-A can supply Ater interface PCM's max to onestandalone TCSM3i rack for Ater interface in oneTCSM3i rack.Working and redundant ETIP1-A's are located inTC2C-0 and TC2C-1 in track 17.

3,7,11,15 All TC2C's

A ETIP1-A master O&M master for A-Interface 4,8,12,16 All TC2C's


20 (127)

11 TCSA RACK CARTRIDGE POSITION INFO

In the table is info of cartridge location when unit or piu is created with MML.Position Cartridge Name1x1-0 CLOC-B CLOC1x1-3 GT4C-A ETC 01x1-6 GT4C-A ETC 11x1-9 GT4C-A ETC 21x2-0 TC2C-A TC2C 01x2-6 TC2C-A TC2C 11x4-0 TC2C-A TC2C 21x4-6 TC2C-A TC2C 31x5-0 TC2C-A TC2C 41x5-6 TC2C-A TC2C 5

x=location letter

Note in commands and in examples in these documents the x is used. User can choose the letter to be used inlive environments.


21 (127)

12 ATER INTERFACE ETIP1-A IMPLEMENTATION FOR IP/PWE INSTANDALONE TCSM

This chapter includes the instructions how to install ETIP1-A plug-in unit used as Ater Interface in StandaloneTCSM3i installation.

ETIP1-A SW update instructions can be found in the end in Appendix 3:Updating embedded software of ETIP1-A

ETIP1-A internal PCM mapping in A- and Ater interface can be found in Appendix 1: Internal PCM usage forAter interface and Appendix 2: Internal PCM usage for A- interface

Note!Only HW redundancy is possible in Ater interface in Standalone TCSM3i with ETIP1-A equipment.

At least TCSM3i cabinets TC2C-0 and TC2C-1 cartridges MUST be upgraded. TC2C-2 TC2C-5 upgrades areoptional.

There is several options in physical Ater connection between the BSC and TCSM in case ETIP1-A in use inTCSM site:

- TCSM ETIP1-A card connected via router to BSC ETIP1-A card

- example TCSM ETIP1-A card connected to Atrica-A2200 where its going outb toBSC site as E1or T1

In this document examples the Ater configuration is done by connecting the TCSM ETIP1-A card viaCisco router to BSC ETIP1-A card

12.1 Ater plug-in unit installation to BSC

12.1.1 When ETIP1-A PIU is used in BSC site to be connected to TCSM ETIP

12.1.1.1 Configure the PW_MANA0 and PW0 for the BSC ETIP1-A cardZQRA:,::,,;

Example:ZQRA:ETIP,2::PW0:;ZQRA:ETIP,2::PW_MANA0;ZQRA:ETIP,2::VLAN150,150,PW_MANA0,:;


22 (127)

ZQRA:ETIP,2::VLAN151,151,PW0,::;

12.1.1.2 Configure the IP address for VLANsZQRN:,::,:,,


23 (127)

PW 0-65534Numerical identifier for PW (Obligatory, must be unique at leastinside one ETIP1-A (Obligatory)

tunnel index 0-65534Numerical identifier of the tunnel in where this PW is included(Obligatory)

local UDP port 1-65535 Number of local UDP port (Obligatory)peer UDP port Number of peer UDP port (Obligatory)

PCM number

0-8191(ETIP)0-127(TCSM) PCM line number (Obligatory)

tsl mapping 1-31 List of timeslots(Optional, default is timeslots 1-31)

JB lenght 1-192

Jitter Buffer length in frames, settable by one frame (125us) steps(Optional, default value is 40 (+/-5ms), range from 1 (+/-125us ) to192 (+/-24ms))

number of frames 1-40Number of collected TDM frames per Ethernet packet (Optional,default is 8)

ToS field 0-63 IP packet ToS field (same as DSCP) (Optional, default is 0)

VLAN priority 0-7

VLAN priority (Optional, if does not set value from IP management isused instead, if there is no VLAN set in IP management thisparameter will be ignored)

PW name Name for PW (Optional, default value is , max length 20)

Example:ZQYC:ETIP,2:322:322:202,202:322:::::::TCSM322:;ZQYC:ETIP,2:320:322:200,200:320::::::TCSM320:;ZQYC:ETIP,2:321:322:201,201:321::::::TCSM321:;

12.1.1.6 Enable PSN tunnel (ZQYJ) or enable single PW traffic inside the tunnel (ZQYE)

Use the QYJ MML command to enable all the PWs in a tunnel.ZQYJ:ETIP,: :;

Name Value Info

unit type

Type of configured unit Type of configured unit(Obligatory, ETIP for ETIPs in BSC3i and TCSMfor ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)tunnel index 0-65534 Numerical identifier for PSN tunnel (Obligatory)action ENA/DIS Action to perform (Obligatory)Example:

ZQYJ:ETIP,2:322:ENA;

Enable single PW traffic inside PSN tunnel

ZQYE:,::;

Name Value Infounit type Type of configured unit Type of configured unit


24 (127)

(Obligatory, ETIP for ETIPs in BSC3i and TCSMfor ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:ETIP,2:320:ENA:;ZQYE:ETIP,2:321:ENA:;

12.1.1.7 Verify information

ZQYI:,:


25 (127)

12.2 TC2C 0 and 1

12.2.1 Move traffic from TC2C 0 and 1 cartridges

Move traffic from TC2C 0 and 1 cartridges.

12.2.2 Delete A-interface configuration

Related A-interface configuration needs to be deleted manually from related ET(s). More instruction can be foundfrom NED document Creating and managing BSC configuration.

Inactivate the A-interface links affected to TC2C-0 and 1 TCSMs.

12.2.2.1 Change the affected links stateZNLC::INA;

12.2.2.2 Deny link activationZNLD:;

12.2.2.3 Change the TCSM unit to SE-NH stateZUSC :TCSM,:BL;ZUSC :TCSM,:TE;ZUSC :TCSM,:SE;ZUSC :TCSM,:SE;

12.2.2.4 Change the speech channels to NU stateZCEC:,:BL;ZCEC:,:NU;

12.2.2.5 Delete speech channelsZRCR:,,;

12.2.2.6 Remove through connected channelZWGR::;

12.2.2.7 Delete transcoder PCMZWGD::,;

12.2.2.8 Disconnect TCSM TR3E/TR3A/TR3T unitsZWUD:TCSM,:,;


26 (127)

12.2.3 Delete TCSM/ET16/TR3/CLS from TC2C 0 and 1 cartridges

Delete Ater TCSM(s) and ET16 /TR3/CLS unit equipments from TC2C-0and 1 with following commands:

ZWTQ:TCSM,::,;ZWTV:TCSM,,;

Note that the location coordinates are needed if two or more plug-inunits are configured to TCSM.

12.2.4 Make cabling changes

In this step, ET16 plug-in unit cables are disconnected.Remove cablings from TC2C-0 and 1 cartridge according to following table:


27 (127)

Equipping CABLE FROM CABLE TONo FU Position FU Position Type Use Note

TCSA_120 TC2C 0 2.0B 19.1C TC2C 0 2.0B 17.2O or2.6B 18.2M

CHE007 PCM Ater interface, internal

TCSA_121 TC2C 0 2.0B 19.1A TC2C 0 2.0B 17.2M CHE007 PCM Ater interface, internalTCSA_122 TC2C 1 2.6B 19.1C TC2C 1 2.6B 17.2O or

2.6B 18.2MCHE007 PCM Ater interface, internal

TCSA_123 TC2C 1 2.6B 19.1A TC2C 1 2.6B 17.2M CHE007 PCM Ater interface, internal

TCSA_246 TC2C 0 2.0B 17.1A CPETS-F/CPETS-H/CPETC-F

04B 32 CPSM017 ET Ater interface,external

TCSA_247 TC2C 0 2.0B 17.1J CPETS-F/CPETS-H/CPETC-F


TCSA_248 TC2C 0 2.0B 17.1R or2.0B 18.1A

CPETS-F/CPETS-H/CPETC-F


TCSA_249 TC2C 0 2.0B 17.1Z or2.0B 18.1J







TCSA_252 TC2C 1 2.6B 17.1R or2.6N 18.1A



TCSA_253 TC2C 1 2.6B 17.1Z or2.6B 18.1J



Remove locking pegs from tracks 17 & 18 tracks and add to needed positions

Add Rear Connector Module RCOM-A + one ADMOD07 + one ADMOD15 Module:


28 (127)

Position ID Name FU Use Note

2.0B 17.1A C111289 RCOM-A TC2C 0 Rear Connector Module for ETIP1-A

putconnectortop of track16 & 17

2.0B 17.4E C108694 ADMOD07 TC2C 02.6B 17.4E C108702 ADMOD15 TC2C 1

Add cabling to TC2C 0 and 1 cartridge according to following table:Equipping CABLE FROM CABLE TO

No FU Position FU Position Type Use Note

TCSA_658 TC2C 0 2.0B 17.1C TC2C 0 2.0B 19.1C CHE008 PCM Ater interface

TCSA_659 TC2C 0 2.0B 17.1A TC2C 0 2.0B 19.1A CHE008 PCM Ater interfaceTCSA_660 TC2C 0 2.0B 17.1G TC2C 1 2.6B 19.1C CHE011 PCM Ater interface

TCSA_661 TC2C 0 2.0B 17.1E TC2C 1 2.6B 19.1A CHE011 PCM Ater interface

TCSA_560 TC2C 0 2.0B 17.4A TC2C 1 2.6B 17.4A CHFX007 2NTCSA_561 TC2C 0 2.0B 17.4G TC2C 1 2.6B 17.4G CHES007 2NTCSA_570 TC2C 0 2.0B 16.1A TC2C 1 2.6B 17.1A CHQ011 PCMTCSA_571 TC2C 0 2.0B 16.1J TC2C 1 2.6B 17.1J CHQ011 PCMTCSA_572 TC2C 0 2.0B 16.1R TC2C 1 2.6B 17.1R CHQ011 PCM

12.2.5 Replace ET16 PIUs with ETIP1-A plug-in unit

Remove ET16 plug-in units from TC2C 0 and 1 cartridge track 17 and/or 18.Install ETIP1-A plug-in unit to TC2C 0 track 17 and install redundant ETIP1-A plug-in unit to TC2C1 track 17.

Rule for TCSM creation is that 4 TR3 units must be at same BSC, so create first 4 units under one BSC

12.2.6 Create first 4 TCSM units and plug-in units under TC2C-0

12.2.6.1 Create theTC2C-0 track 1 TCSM unit and plug-in units

Two options a) when ET16 is used for A-interface and b) when ETIP1-A used forA-interface ( in case A-interface upgraded earlier for ETIP1-A)

a. TCSM unit when ET16 in use (A-interface ET master)

ZWTU:TCSM, :1x2-0; /TCSM unit in TC2C-0ZWTP:TCSM,:1x2-6:,0,1::GENERAL,8,,TSL,1::;

ZWTU:TCSM,>:1x1-3:; /ET unit for TCSM under GTICZWTP:TCSM,,1x1-3:ET16,0,1,:::;

ZWGC:,:POOL=:BCSU,:;ZWUC:TCSM,:,0;


29 (127)

b. TCSM unit when ETIP1-A used forA-interface ( in case A-interface upgraded earlier for ETIP1-A)

ZWTU:TCSM, :1x2-0;ZWTP:TCSM,:1x2-6:,0,1::GENERAL,8,,TSL,1::;

Create TCSM pool and connect the unit


12.2.6.2 Create the TC2C-1 track 2 TCSM units and plug-in units (Clock master)

Create TCSM units

ZWTU:TCSM,:1x2-0; /TCSM units in TC2C-0ZWTP:TCSM,:1x2-0:,0,2,::GENERAL,8,,TSL,1::;

ZWTU:TCSM,:1x1-0:; /Clock unit locationZWTP:TCSM,,1x1-0:CL3TG,0,0:;ZWTP:TCSM,,1x1-0:CL3TG,1,3:;



12.2.6.3 Create the TC2C-1 track 3 TCSM units and plug-in units (Ater-interface ETIP master)

ETIP master and redundant TCSM units

ZWTU:TCSM,:1x2-0; // master ETIP TCSM units in TC2C-0ZWTU:TCSM,:1x2-6:; // Redundant ETIP TCSM unit

Create Plug in units under TCSM unit

ZWTP:TCSM,:1x2-0:,0,3,::GENERAL,8,,TSL,1::;ZWTP:TCSM,,1x2-0:ETIP1_A,0,17,:::;ZWTP:TCSM,,1x2-6:ETIP1_A,1,17,:::;


ZWGS::< number of through connected channels>:;ZWGC:,:POOL=:BCSU,:;ZWUC:TCSM,:,0;ZWGA::;

12.2.6.4 Create the TC2C-1 track 4 TCSM units and plug-in units

Two options a) when ET16 is used for A-interface and b) when ETIP1-A used forA-interface ( in case A-interface upgraded earlier for ETIP1-A)

a. TCSM unit when ET16 in use (A-interface ET master)

ZWTU:TCSM,:1x2-0;ZWTP:TCSM,:1x2-0:,0,4,::GENERAL,8,


30 (127)

,TSL,1::;

b. TCSM unit when Transmission protected ETIP1-A in use (A-interface ETmaster) ( in case A-interface upgraded earlier for ETIP1-A)

ZWTU:TCSM, :1x2-0; // TCSM unit in TC2C-0ZWTP:TCSM,:1x2-0:,0,4,::GENERAL,8,,TSL,1::;

ZWTU:TCSM,>:1x1-3:; /ET unit for TCSM under GTICZWTU:TCSM,>:1x1-6:; /in case HW redundancy in use for A-if ETIP

ZWTP:TCSM,:1x2-0:,0,4,::GENERAL,8,,TSL,1::;ZWTP:TCSM,,1x1-3:ETIP1_A,0,7,:::; // in case HW and transmissionredundancy in useZWTP:TCSM,,1x1-6:ETIP1_A,0,6,:::; // in case HW redundancy in use

c. TCSM unit when HW protected ETIP1-A in use (A-interface ET master) (incase A-interface upgraded earlier for ETIP1-A)

ZWTU:TCSM, :1x2-0; // TCSM unit in TC2C-0ZWTP:TCSM,:1x2-0:,0,4,::GENERAL,8,,TSL,1::;

ZWTU:TCSM,>:1x1-3:; /ET unit for TCSM under GTICZWTP:TCSM,,1x1-3:ETIP1_A,0,7,:::; /master unit in case HWredundancy in use

ZWTU:TCSM,>:1x1-6:; /in case HW redundancy in use for A-if ETIPZWTP:TCSM,,1x1-6:ETIP1_A,0,6,:::; // protected unit in case HWredundancy in use

Create TCSM PCM


a) Example of TC2C-0 first 4 TCSM unit creation under TC2C-0 ( when A-interfaceET16 in use and Ater interface ETIP1-A in use):

ZWTU:TCSM,320:1x2-0:; //A-IF TR3 masterZWTU:TCSM,320:1x1-3:; // A-if ET16 masterZWTP:TCSM,320:1x2-0:TR3E,0,1,::GENERAL,8,320,TSL,1::;ZWTP:TCSM,320,1x1-3:ET16,0,1,:::;ZWGC:320,1:POOL=32:BCSU,0:;ZWUC:TCSM,320:TR3E,0;

ZWTU:TCSM,321:1x2-0:;"); //Clock masterZWTU:TCSM,321:1x1-0:;ZWTP:TCSM,321:1x2-0:TR3E,0,2,::GENERAL,8,321,TSL,1::;ZWTP:TCSM,321,1x1-0:CL3TG,0,0:;ZWTP:TCSM,321,1x1-0:CL3TG,1,3:;ZWGC:321,1:POOL=32:BCSU,0:;ZWUC:TCSM,321:TR3E,0;


31 (127)

ZWTU:TCSM,322:1x2-0:;"); //Ater ETIP masterZWTU:TCSM,322:1x2-6:; // Redundant ETIP unitZWTP:TCSM,322:1x2-0:TR3E,0,3,::GENERAL,8,322,TSL,1::;ZWTP:TCSM,322:1x2-0:ETIP1_A,0,17,:::; //master ETIPZWTP:TCSM,322,1x2-6:ETIP1_A,1,17,:::; //redundant ETIPZWGS:322:1:;ZWGC:322,1:POOL=32:BCSU,0:;ZWUC:TCSM,322:TR3E,0;ZWGA:322-31:1-31:;

ZWTU:TCSM,323:1x2-0:; //Fourth TCSM unitZWTP:TCSM,323:1x2-0:TR3E,0,4,::GENERAL,8,323,TSL,1::;ZWGC:324,1:POOL=32:BCSU,0:;ZWUC:TCSM,324:TR3E,0;

b) Example of TC2C-0 A-and Ater interface masters and clock master creation when A-interface ETIP use transmission protection in case the A-interface has been upgradedearlier:

ZWTU:TCSM,320:1x2-0:; //first TCSM unitZWTP:TCSM,320:1x2-0:TR3E,0,1,::GENERAL,8,320,TSL,1::;ZWGC:320,1:POOL=32:BCSU,0:;ZWUC:TCSM,320:TR3E,0;

ZWTU:TCSM,321:1x2-0:;"); //Clock masterZWTU:TCSM,321:1x1-0:;ZWTP:TCSM,321:1x2-0:TR3E,0,2,::GENERAL,8,321,TSL,1::;ZWTP:TCSM,321,1x1-0:CL3TG,0,0:;ZWTP:TCSM,321,1x1-0:CL3TG,1,3:;ZWGC:321,1:POOL=32:BCSU,0:;ZWUC:TCSM,321:TR3E,0;

ZWTU:TCSM,322:1x2-0:;"); //Ater ETIP masterZWTU:TCSM,322:1x2-6:; // Redundant ETIP unitZWTP:TCSM,322:1x2-0:TR3E,0,3,::GENERAL,8,322,TSL,1::;ZWTP:TCSM,322:1x2-0:ETIP1_A,0,17,:::; //master ETIPZWTP:TCSM,322,1x2-6:ETIP1_A,1,17,:::; //redundant ETIPZWGS:322:1:;ZWGC:322,1:POOL=32:BCSU,0:;ZWUC:TCSM,322:TR3E,0;ZWGA:322-31:1-31:;

ZWTU:TCSM,323:1x2-0:; //A-interface TCSM masterZWTU:TCSM,323:1x1-3:; //A-interface ETIP masterZWTP:TCSM,323:1x2-0:TR3E,0,4,::GENERAL,8,323,TSL,1::;ZWTP:TCSM,323,1x1-3:ETIP1_A,0,7,:::;ZWGC:323,1:POOL=32:BCSU,0:;ZWUC:TCSM,323:TR3E,0;


32 (127)

12.2.7 Create rest of the TCSM units to TC2C-0 and 1

Note!! Remember to check and create the A-and Ater-interface master units see table in chapter 10 Master unitsin TCSM site

12.2.7.1 Create the TCSM(s) units for TR3 and ET16 or ETIP1-A

ZWTU:TCSM:;

12.2.7.2 Create the TR3E/TR3A/TR3T plug-in units

ZWTP:TCSM,::,,::GENERAL,8,,,;

12.2.7.3 Create the ET16 for A-interface (TR3 A-interface O&M masters located in tracks 1, 5, 9,13)

ZWTP:TCSM,:ET16,,:;

12.2.7.4 Create the ETIP1-A for Ater interfaces (TR3 Ater-interface O&M masters located in tracks3,7,11,15)

ZWTP:TCSM,:ETIP1_A,,:;

12.2.7.5 Create the ETIP1-A for A-interfaces (TR3 A-interface O&M masters located in tracks4,8,12,16) (in case A-interface upgraded earlier for ETIP1-A)

ZWTP:TCSM,:ETIP1_A,,:;Remember to create both master and protected units in case HW redundancy in use

12.2.7.6 Connect TCSM unit

ZWUC:TCSM,:,;

12.2.7.7 Set the number of through connections

ZWGS::;

12.2.7.8 Create the TC-PCM

ZWGC::POOL=:BCSU,;

12.2.7.9 Create the through connections

ZWGA:: ;


33 (127)

12.2.8 Create IP/PW locally to the Ater master and redundant ETIP1-A units

This step is to be done locally. The first PWE tunnel and PW need to be configuredlocally to ETIP plug-in unit. The rest of the PWE tunnels and PW can be configured fromBSC site. Configuring the IP and PW for ETIP unit can be done following the document:PWT User Guide (documents chapter 4 and 5). See NED document PWT User Guidefor more information.

12.2.8.1 Configure locally master ETIP1-A unit for Ater interface PWa. from back panel with CPCU020 cable connection in ETIP1-A card in TC2C-0 track

17

Service Terminal connection to ETIP1-A is available through the back panel. Connect CPCU020 cable(C104887) to the back panel connector 4P with traffic parameters 9600/ Even / 7.Username: rootPassword: root1234

b. from front panel cable connection in ETIP1-A card in TC2C-0 track 17

Take a SSH session with a direct Ethernet cable attached into front-panel SFP module. The card defaultaddress is 192.168.1.111/24 and the client must use IP address from 192.168.1.0/24 subnet.

Username; rootPassword: root1234

Modify IP address, VLAN and route use linux vi-editor

12.2.8.2 Configure PW_MANA0, PW0 and IP addresses to script file using vi -editorvi /opt/etip_tcsm_ip_conf.sh

ifconfig pw_mana0. netmask xxx.xxx.xxx.xxxifconfig pw0. netmask xxx.xxx.xxx.xxxifconfig pw_mana0 up

Exit with ESC and :ZZ or ESC save with :w and exit with :q!

Example:ifconfig pw_mana0.152 10.16.65.180 netmask 255.255.255.248ifconfig pw0.153 10.16.65.188 netmask 255.255.255.248ifconfig pw_mana0 up

12.2.8.3 Configure PW_MANA0, PW0 VLANs to script file using vi -editorvi /opt/etip_tcsm_vlan_conf.sh

vconfig add pw_mana0 vconfig add pw0


Example:vi /opt/etip_tcsm_vlan_conf.sh

vconfig add pw_mana0 152


34 (127)

vconfig add pw0 153

12.2.8.4 Configure the static network routes to script file using vi editorvi /opt/etip_tcsm_routes_conf.sh

route add -net netmask xxx.xxx.xxx.xxxgw route add -net netmask xxx.xxx.xxx.xxx gw

Exit with ESC and :ZZ or ESC save with :w and exit with :q!Example:

vi /opt/etip_tcsm_routes_conf.sh

route add -net 10.16.65.160 netmask 255.255.255.248 gw 10.16.65.177route add -net 10.16.65.168 netmask 255.255.255.248 gw 10.16.65.185

12.2.8.5 Restart the ETIP master unitlnx-hwapi-tool -f 0

12.2.8.6 Configure locally the redundant ETIP1-A unit for Ater interface PW by using local cableconnection in ETIP1-A card in TC2C-1 track 17

a. from back panel with CPCU020 cable connection in ETIP1-A card in TC2C-1 track17

Service Terminal connection to ETIP1-A is available through the back panel. Connect CPCU020 cable(C104887) to the back panel connector 4P with traffic parameters 9600/ Even / 7.Username: rootPassword: root1234

b. from front panel cable connection in ETIP1-A card in TC2C-1 track 17

Take a SSH session with a direct Ethernet cable attached into front-panel SFP module. The card defaultaddress is 192.168.1.111/24 and the client must use IP address from 192.168.1.0/24 subnet.

Username; rootPassword: root1234

Modify IP address, VLAN and route use linux vi-editor

12.2.8.7 Configure PW_MANA0, PW0 and IP addresses to script file using vi -editorvi /opt/etip_tcsm_ip_conf.sh

ifconfig pw_mana0. netmask xxx.xxx.xxx.xxxifconfig pw0. netmask xxx.xxx.xxx.xxxifconfig pw_mana0 up


Example:ifconfig pw_mana0.152 10.16.65.181 netmask 255.255.255.248


35 (127)

ifconfig pw0.153 10.16.65.188 netmask255.255.255.248ifconfig pw_mana0 up

12.2.8.8 Configure PW_MANA0, PW0 VLANs to script file using vi -editorvi /opt/etip_tcsm_vlan_conf.sh

vconfig add pw_mana0 vconfig add pw0


Example:

vi /opt/etip_tcsm_vlan_conf.shvconfig add pw_mana0 152vconfig add pw0 153

12.2.8.9 Configure the static network routes to script file using vi editorvi /opt/etip_tcsm_routes_conf.sh

route add -net netmask xxx.xxx.xxx.xxxgw route add -net netmask xxx.xxx.xxx.xxx gw

Exit with ESC and :ZZ or ESC save with :w and exit with :q!Example:

vi /opt/etip_tcsm_routes_conf.shroute add -net 10.16.65.160 netmask 255.255.255.248 gw 10.16.65.177route add -net 10.16.65.168 netmask 255.255.255.248 gw 10.16.65.185

12.2.8.10 Restart the ETIP master unitlnx-hwapi-tool -f 0

12.2.9 Add Tunnel and PW configuration of ETIP master unit for ETIP master TCSM unit inTC2C-0 track 3

Add tunnel:

lnx-pwe-tool a -n=

Create the PW under the tunnel:

lnx-pwe-tool c -p=

Name Value Info


36 (127)

pwindex 0-65534 PW indextunnelindex 0-65534 Tunnel idludp 1-65535 Local UDP portpudp 1-65535 Peer UDP port

pcm 0-8191PCM line number( in TCSM site starting from 0)

PCM numbering table in Appendix 2: Internal PCM usage for Aterinterface

Change the tunnel state:lnx-pwe-tool j ena

Example:lnx-pwe-tool a 322 10.16.65.172 -n=ATERTOETIP2lnx-pwe-tool c 322 322 202 202 2 p=TCSM322lnx-pwe-tool j 322 ena

12.2.9.1 Go to MML to check the D-channel stateZDTF;

12.2.9.2 Take the Ater master TCSM unit to TE-EX (in TC2C-0 track 3)When the d-channel for TCSM is up take the unit up:ZUSC:TCSM,:SE;ZUSC:TCSM,:TE;

12.2.9.3 Connect locally to Ater ETIP1-A master unit (in TC2C-0 track 17) and upload theconfiguration from ETIP1-A card to TR3 card:

lnx-config-tool -u TR3

12.2.9.4 Take the Ater master TCSM unit to WO-EXZUSC:TCSM,:WO;

When the Ater master TCSM unit D-channel is in WO-EX continueconfiguring the rest of the TCSM units via MML

12.2.10 Create new PSN tunnel (or use the one created to Ater master)

Use the QYA MML command or the lnx-pwe-tool a command locally from ETIP to create a new PSN tunnel.ZQYA:,,:::;

Name Value Info

unit type



37 (127)

unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)

tunnel index 0-65534Numerical identifier for PSN tunnel (Obligatory,must be unique at least inside one ETIP1-A

dst IP address Destination IP address of tunnel (Obligatory)

tunnel nameName for PSN tunnel (Optional, default value is ,max length 20)

Example:ZQYA:TCSM,324,ATER:322:"10.16.65.188":ATERTOTCSM324:;

12.2.10.1 Create new PW inside PSN tunnelUse the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunnel.ZQYC:,,:: :,:::::::;Name Value Info

unit typeType of configured unit Type of configured unit (Obligatory,ETIP for ETIPs in BSC3i and TCSM for ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)

interface type A or Ater A-interface or Ater (only when unit type TCSM)

PW 0-65534Numerical identifier for PW (Obligatory, must be unique atleast inside one ETIP1-A (Obligatory)


local UDP port 1-65535 Number of local UDP port (Obligatory)

peer UDP port Number of peer UDP port (Obligatory)

PCM number

0-8191(ETIP)

PCM line number (Obligatory)0-127 (TCSM)

tsl mapping 31-Jan List of timeslots(Optional, default is timeslots 1-31)

JB lenght 1-192

Jitter Buffer length in frames, settable by one frame (125us)steps (Optional, default value is 40 (+/-5ms), range from 1 (+/-125us ) to 192 (+/-24ms))

number of frames Jan-40Number of collected TDM frames per Ethernet packet(Optional, default is 8)


VLAN priority 0-7

VLAN priority (Optional, if does not set value from IPmanagement is used instead, if there is no VLAN set in IPmanagement this parameter will be ignored)



38 (127)

Example:ZQYC:TCSM,322,ATER:320:322:200,200:0::::::TCSM320:;ZQYC:TCSM,322,ATER:321:322:201,201:1::::::TCSM321:;ZQYC:TCSM,322,ATER:323:322:203,203:2::::::TCSM323:;//TCSM322 commands has been given locally in ETIP card//


Use the QYJ MML command to enable all the PWs in a tunnel.

ZQYJ: ,, ::;

Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)tunnel index 0-65534 Numerical identifier for PSN tunnel (Obligatory)action ENA/DIS Action to perform (Obligatory)Example:

ZQYJ:TCSM,322,ATER:322:ENA;


ZQYE:,,::;Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:TCSM,322,ATER:320:ENA;ZQYE:TCSM,322,ATER:321:ENA;ZQYE:TCSM,322,ATER:323:ENA;//TCSM322 commands has been given locally in ETIP card//

12.2.10.3 Verify information

ZQYI:,:


39 (127)

(Obligatory, ETIP for ETIPs in BSC3i andTCSM for ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)tunnel index 0-65534 Numerical identifier for PSN tunne (Obligatory)PW index 0-65534 Numerical identifier for PW (Optional)

PCM number0-8191(ETIP)0-127 (TCSM)

Number of inquired PCM (Optional, range inETIP 0 - 8191 and in TCSM 0 - 127)


12.2.10.5 Take the TCSM unit to WO-EXWhen the d-channel for TCSM is up take the unit up:ZUSC:TCSM,:SE;ZUSC:TCSM,:TE;ZUSC:TCSM,:WO;

12.2.11 Move traffic back to TC2C 0 and 1 cartridge

Create needed A-interface configuration to standalone TCSM related to ETIP. See more instructions from NEDdocument BSS IntegrationAfter that, move traffic back to new ETIP unit.

12.2.11.1 Change the PCM number of the A-interface link with ZNCM MML command if neededModify the link PCM number:

ZNCM::;

Allow link activation:

ZNLA:;

Cange the links state:

ZNLC::ACT;

12.2.11.2 Create circuits back and take the circuits up

Create circuit group:ZRCC:TYPE=CCS,NCGR=,CGR=:DIR=,NET=,SPC=,LSI=;

Create circuits under circuit group:

ZRCA:CGR=1:ETPCM=,CRCT=:CCSPCM=:;

Change the state of the speech circuits (CEC).

ZCEC:ETPCM=,CRCT=:;ZCEC:ETPCM=,CRCT=:WO;


40 (127)

12.2.11.3 Restart the TCSM units with code loading

ZUSU:TCSM,:C=TOT;


41 (127)

12.3 TC2C 2 (optional)

12.3.1 Move traffic from TC2C 2 cartridge

Move traffic from TC2C 2 cartridge to be upgraded.



Inactivate the A-interface links affected to TC2C-2 TCSMs










42 (127)

12.3.3 Delete TCSM/ET16/TR3 from TC2C 2 cartridge

Delete Ater ET16/TR3 equipment related to TCSM units.Delete Ater TCSM(s) and ET16/TR3 unit equipments from TC2C-2 with following commands:ZWTQ:TCSM,::,;ZWTV:TCSM,,;

Note that the location coordinates are needed if two or more plug-in units are configured to TCSM.


In this step, ET16 plug-in unit cables are disconnected.Remove cablings from TC2C 2 cartridge according to following table:









TCSA_256 TC2C 2 4.0B 17.1R or4.0B 18.1A



TCSA_257 TC2C 2 4.0B 17.1Z or4.0B 18.1J



Add or move locking pegs to needed positions when cabling.Add cablings to TC2C 2 cartridge according to following table:


43 (127)


TCSA_662 TC2C 0 2.0B 17.1L TC2C 2 4.0B 19.1C CHE020 PCM Aterinterface

TCSA_663 TC2C 0 2.0B 17.1J TC2C 2 4.0B 19.1A CHE020 PCM Aterinterface

12.3.5 Remove ET16 PIUs

Remove ET16 plug-in units from TC2C 2 cartridge track 17 and/or 18.

12.3.6 Create the TCSM units to TC2C-2


12.3.6.1 Create the TCSM(s) units for TR3 and ET16 units

ZWTU:TCSM:;




ZWTP:TCSM,:ET16,,:;

Create the ETIP1-A for Ater interfaces (TR3 Ater-interface O&M masters located in tracks 3,7,11,15):ZWTP:TCSM,:ETIP1_A,,:;




ZWUC:TCSM,:,;


ZWGS::;



44 (127)

ZWGC::POOL=:BCSU,;


ZWGA:: ;

12.3.7 Create IP/PW

This step is to be done manually. Configuring the IP and PW for ETIP unit can be donefollowing the document: PWT User Guide (documents chapter 4 and 5). See NEDdocument PWT User Guide for more information.

Use existing Ater ETIP Master TCSM when creating tunnels and PWs to other TCSMs.

12.3.7.1 Create new PSN tunnel ( or use the one created to Ater master)Use the QYA MML command or the lnx-pwe-tool a command locally from ETIP to create a new PSN tunnel.ZQYA:,,:::;

Name Value Info

unit type







12.3.7.2 Create new PW inside PSN tunnelUse the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunneZQYC:,,:: :,:::::::;Name Value Info

unit typeType of configured unit Type of configured unit (Obligatory, ETIP forETIPs in BSC3i and TCSM for ETIPs in TCSM3i)





45 (127)




PCM number



JB lenght 1-192




VLAN priority 0-7

VLAN priority (Optional, if does not set value from IP management isused instead, if there is no VLAN set in IP management thisparameter will be ignored)


Example:ZQYC:TCSM,322,ATER:320:322:200,200:0::::::TCSM320:;


Use the QYJ MML command to enable all the PWs in a tunnel.

ZQYJ:ETIP,,: :;

Name Value Info

unit type


unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)tunnel index 0-65534 Numerical identifier for PSN tunnel (Obligatory)action ENA/DIS Action to perform (Obligatory)Example:

ZQYJ:TCSM,322,ATER:322:ENA;


ZQYE:,,::;Name Value Infounit type Type of configured unit Type of configured unit


46 (127)

(Obligatory, ETIP for ETIPs in BSC3i and TCSMfor ETIPs in TCSM3i)

unit index Index of ETIP or TCSM unit (Obligatory)interface type A or Ater A-interface or Ater (only when unit type TCSM)PW index 0-65534 Numerical identifier for PW (Obligatoryaction ENA/DIS Action to perform (Obligatory, range ENA or DIS)

Example:ZQYE:TCSM,322,ATER:320:ENA;ZQYE:TCSM,322,ATER:321:ENA;ZQYE:TCSM,322,ATER:323:ENA;//TCSM322 commands has been given locally in ETIP card//


12.3.7.5 Take the Ater master TCSM unit to WO-EXWhen the d-channel for TCSM is up take the unit up:ZUSC:TCSM,:SE;ZUSC:TCSM,:TE;ZUSC:TCSM,:WO;

12.3.8 Move traffic back to TC2C 2 cartridge

Create needed A-interface configuration to standalone TCSM related to ETIP. See more instructions from NEDdocument BSS IntegrationAfter that, move traffic back to new ETIP unit.

12.3.8.1 Change the PCM number of the A-interface link with ZNCM MML command if neededModify the link PCM number:

ZNCM::;

Allow link activation:

ZNLA:;

Cange the links state:

ZNLC::ACT;

12.3.8.2 Create circuits back and take the circuits upCreate circuit group:

ZRCC:TYPE=CCS,NCGR=,CGR=:DIR=,NET=,SPC=,LSI=;

Create circuits under circuit group:

ZRCA:CGR=1:ETPCM=,CRCT=:CCSPCM=:;


47 (127)

Change the state of the speech circuits (CEC).

ZCEC:ETPCM=,CRCT=:;ZCEC:ETPCM=,CRCT=:WO;

12.3.8.3 Restart the TCSM units with code loading

ZUSU:TCSM,:C=TOT;


48 (127)

12.4 TC2C 3 (optional)

12.4.1 Move traffic from TC2C 3 cartridge

Move traffic from TC2C 3 cartridge to be upgraded.



Inactivate the A-interface links affected to TC2C-3 TCSMs










49 (127)

12.4.3 Delete TCSM/ET16/TR3 from TC2C 3 cartridge

Delete ET16/TR3 equipment related to TCSM units.

Delete TCSM(s) and ET16/TR3 unit equipments with following commands:

ZWTQ:TCSM,::,;ZWTV:TCSM,,;

Note that the location coordinates are needed if two or more plug-in units are configuredto TCSM.


In this step, ET16 plug-in unit cables are disconnected.Remove cablings from TC2C 3 cartridge according to following table:









TCSA_260 TC2C 3 4.6B 17.1R or4.6B 18.1A



TCSA_261 TC2C 3 4.6B 17.1Z or4.6B 18.1J



Add or move locking pegs to needed positions when cabling.Add cablings to TC2C 3 cartridge according to following table:


50 (127)


TCSA_664 TC2C 0 2.0B 17.1P TC2C 3 4.6B 19.1C CHE016 PCM Aterinterface

TCSA_665 TC2C 0 2.0B 17.1N TC2C 3 4.6B 19.1A CHE016 PCM Aterinterface

12.4.5 Remove ET16 PIUs

Remove ET16 plug-in units from TC2C 3 cartridge track 17 and/or 18.

12.4.6 Create the TCSM units to TC2C-3


12.4.6.1 Create the TCSM(s) units for TR3 and ET16 units

ZWTU:TCSM:;




ZWTP:TCSM,:ET16,,:;

12.4.6.4 Create the ETIP1-A for Ater interfaces (TR3 Ater-interface O&M masters located in tracks3,7,11,15)

ZWTP:TCSM,:ETIP1_A,,:;




ZWUC:TCSM,:,;


51 (127)


ZWGS::;


ZWGC::POOL=:BCSU,;


ZWGA:: ;

12.4.7 Create IP/PW

This step is to be done manually. Configuring the IP and PW for ETIP unit can be done following the document:PWT User Guide (documents chapter 4 and 5). See NED document PWT User Guide for more information.Use existing Ater ETIP Master TCSM when creating tunnels and PWs to other TCSMs.

12.4.7.1 Create new PSN tunnel ( or use the one created to Ater master)Use the QYA MML command or the lnx-pwe-tool a command locally from ETIP to create a new PSN tunnel.ZQYA:,,:::;

Name Value Info

unit type







12.4.7.2 Create new PW inside PSN tunnelUse the QYC MML command or the lnx-pwe-tool c command locally from ETIP to create a new PW inside thePSN tunnel.

ZQYC:,,:: :,:::::::;

Name Value Info

unit typeType of configured unit Type of configured unit (Obligatory, ETIP forETIPs in BSC3i and TCSM for ETIPs in TCSM3i)


52 (127)







PCM number



JB lenght 1-192




VLAN priority 0-7

VLAN priority (Optional, if does not set value from IP management isused instead, if the

Standalone TCSM3i ETIP1-A Implementation for IPPWE (S12-14 TCSM HW)-Ver-1_0

Documents

Transcript of Standalone TCSM3i ETIP1-A Implementation for IPPWE (S12-14 TCSM HW)-Ver-1_0