P/N 9961084 Rev 01 09/14 Page 1 of 10

BEFORE YOU BEGINRead these instructions thoroughly and make sure all parts and tools are accounted for. Please retain these installation instructions for future reference and parts ordering information.

P/N 2880603

SLINGSHOT INFOTAINMENT KIT

APPLICATIONSLINGSHOT

8

25

149

1019

7

1

2322

15

21

18

1716 6

13

11

19

4

19

12

5

20

2

3

24

20

26

P/N 9961084 Rev 01 09/14 Page 2 of 10

APPROXIMATE ASSEMBLY TIME3 hrsIMPORTANTThis SLINGSHOT INFOTAINMENT KIT is exclusively designed for use with this vehicle. Please read the installation instructions thoroughly before beginning. Installation is easier if the vehicle is clean and free of debris. For your safety, and to ensure a satisfactory installation, perform all installation steps correctly in the sequence shown.

TOOLS NEEDED6 mm Allen Wrench 3/8” Ratchet 3” Extension 8 mm Socket Pliers2.5 mm Allen Wrench T27 Torx Driver T40 Torx Driver 10 mm Socket Wire Cutters

KIT CONTENTSRef Qty Part Description Part Number

1 1 Harness Assembly, AM/FM Antenna 24114892 1 Harness-Radio, SS 24125033 1 Radio Assembly, 50Wx2, SS, Programed 24127964 1 Enclosure Assembly, Speaker, LH 24127985 1 Enclosure Assembly, Speaker, RH 24127996 1 Display-Radio, SS 32806007 1 Mount-Antenna, 90 DEG ADJ 40122748 1 Antenna-Mast, AM/FM, Short 40148499 1 Camera-Backup 401501810 1 Mount Plate-Bracket, Antenna, Rear 525955411 1 Mount-Radio, Receiver, Lower, E-Coat 525958312 1 Mount-Radio, Receiver, Upper, E-Coat 525958413 1 Mount-Radio Display 545128514 1 Mount-Backup Camera 545151115 4 Panduit Strap 708013816 1 Trim-Radio Display Bezel, TITM 718068517 1 Emblem, Radio, LH 718092918 1 Emblem, Radio, RH 718093019 9 Screw-HXFL-M6X1.0X16 8.8 ZY3 751854820 4 Screw-M6X1X40, TR/TX-Black 751900121 4 Screw-M4X0.7X30 10.9 ZPB 752019022 1 Nut-M5X0.8, Nyloc-SS 754705923 1 Flat Washer 5.3X30X1.5 755654424 1 Plug-Radio 541492725 1 Washer-1/4 Spring Lock-Y 755280126 3 Expansion Clip, 6mm 7081304

1 Instructions 9961084

P/N 9961084 Rev 01 09/14 Page 3 of 10

ANTENNA INSTALLATION INSTRUCTIONS1. Pull up the part (A) as shown in figure.

2. Remove the plastic top deck per the service manual or optionally cut out a rectangular section of plastic (B) to allow access for mounting the antenna as shown in the figure. Drill a 1/4” (6mm) min. diameter hole in each corner, then use a small saw or rotary tool to connect the corners (be sure to stay away from the edges to avoid damaging the painted surfaces).

A

B

3. Assemble the antenna partsa. Install antenna mount stud (7) into the mount

plate (10) aligning the locating pin on the mount in the plate.

b. Install antenna cable (1) round end onto the stud with the cable end facing toward the tab side of the plate. Place the cable (1) end with the teeth toward the plate.

c. Install washer (23) and nut (22) on the stud of the antenna mount.

d. Tighten to 25 in-lbs. (2.8 Nm) and position cap over nut making sure to lock the tabs in the cap on the washer.

e. Install antenna mast (8) onto base with lock washer (25) and hand tighten snug.

7

23 221

8

10

19

25

P/N 9961084 Rev 01 09/14 Page 4 of 10

f. Install antenna mount to rear center of frame tube with two screws (20). Torque screws to 8 ft. lbs. (10.8 Nm).NOTE: Antenna mast faces straight back and up slightly.

g. Remove the highlighted cup holder (C) & brake lever boot (D) to assist the routing path. Refer to figures.

h. Remove the storage compartment (E) from the vehicle interior body.

i. Using a rigid piece of wire and working from opening to opening, route antenna wire (F) down passenger side of frame and up to the opening where the storage compartment used to be.NOTE: Raising vehicle off of the ground and supporting securely to allow access to wiring underneath vehicle will aid in routing the cable.

C

D

j. Place four panduit straps (15) along the antenna cable (1) to hold it securely away from moving parts, such as the E-brake handle.

115

E

F

P/N 9961084 Rev 01 09/14 Page 5 of 10

RADIO HARNESS INSTALLATION INSTRUCTIONS1. Pull the latch and open the front hood (A) by tilting it

to the maximum position.

3. Connect the 3-cavity power connector from the radio harness (2) to the mating 3-cavity power connector on the main harness through the opening in the center console where the storage compartment used to be. 2

A

2. Remove the ECM (B) and plastic mount (C).

BC

P/N 9961084 Rev 01 09/14 Page 6 of 10

3. Route harness according to the figure at right and push the x-mas tree clips into the corresponding holes in frame, which are circled in the figure.a. Connect the diagnostic mate on the radio harness

to the diagnostic plug under the steering column and relocate by ECM mount (E).

b. Route the new diagnostic connector under steering column and secure where original connector (D) was located.

4. Route RH speaker wire to outside of the frame and under the outside frame joint. Remove the rubber plug from the glove box and insert the USB connector (F) through the hole until the grommet is fully seated.

F

5. Route LH speaker wire to outside of frame and under the outside frame joint.

D

E

FRONT

FRONT

P/N 9961084 Rev 01 09/14 Page 7 of 10

1. Remove the existing body fastener (A) on each side of the vehicle which will be re-used to mount the speaker enclosures.

2. Mount the LH (4) and RH (5) speaker enclosure onto vehicle by inserting three screws (20) on the chassis frame. Tighten the bolts to 6 ft. lbs. (8.2 Nm).

3. Connect the routed harness to the radio speaker. See Figure.

RADIO SPEAKER INSTALLATION INSTRUCTIONS

A

REAR CAMERA INSTALLATION INSTRUCTIONS1. Remove the plastic part (A) shown in figure and

discard it.

A

20

5

4

P/N 9961084 Rev 01 09/14 Page 8 of 10

2. Unscrew the fasteners (B) from the locations shown in figure. This will allow you to separate the top/bottom plastic bodywork to make the electrical connection.

B

14

3. Snap fit the camera (9) into the new part (14), make sure to align the orientation sticker with the arrow.

4. Connect the camera to the mating connector (C), which is already present on the vehicle harness; connector is taped to the bundle near the license plate wire bundle.

5. Snap the plastic camera mount into place.6. Reinstall the three fasteners (B) removed in Step 2.

Tighten to 6 ft. lbs. (8.2 Nm)

C

9

P/N 9961084 Rev 01 09/14 Page 9 of 10

RADIO INSTALLATION INSTRUCTIONS1. Install the rubber connector plug (24) into the 32 pin

connector on the short side of the radio. 2. Install three expansion clips (26) into the plastic

inner dash support as shown.3. Install the lower mounting bracket (11) to the vehicle

by inserting three bolts (19) into the expansion clips. Tighten to 6 ft. lbs. (8.2 Nm).

4. Install radio (3) to the upper mounting bracket (12) with the 36 pin connector on the long side of the radio facing up using 2 bolts (19) through the top 2 holes in the bracket and into the threaded inserts in the radio. The flange on the bracket should be facing away from the radio, and the bracket should rest against the flat side of the radio (see figure). Tighten to 6 ft. lbs. (8.2 Nm).

5. Install the upper bracket and radio assembly to the lower bracket (11) by placing the upper bracket behind the mounting flange on the lower bracket. Insert 2 bolts (19) through the lower bracket, the lower 2 holes in the upper bracket, and into the threaded inserts in the radio. Tighten to 6 ft. lbs. (8.2 Nm).

6. Connect the 36 pin large gray connector from the radio harness to the top of the radio. Make sure it locks into place by gently pulling on it.

7. Route antenna wire over the top of the front frame tube and back to the radio and connect to the female pigtail coming out of the radio. Push until fully seated.

12

19

11

3

26

19

26

P/N 9961084 Rev 01 09/14 Page 10 of 10

RADIO DISPLAY INSTALLATION INSTRUCTIONS

1. Install radio display (6) into the mount (13) with the electrical connectors to the top side.2. Install radio trim (16) to the outside of the radio display with Slingshot to the bottom side.3. Install LH radio (17) emblem over the display buttons on LH side.4. Install RH radio (18) emblem over the display buttons on RH side.5. Install four screws (21) through the emblem, trim, display and into the mount and tighten the screws to

36 in-lbs. (4 Nm).6. Connect radio harness (2) wire labeled B to the B port on the back of display.7. Connect the main harness labeled display to the D port on the back of the display8. Snap radio display into center console of bike with electrical connectors on the top side.

1716

18

13

621

2