SINUMERIK 840D/810D/FM-NC - HILLARY MACHINERY | … · · 2010-10-10SINUMERIK 840D/810D/FM-NC...
Transcript of SINUMERIK 840D/810D/FM-NC - HILLARY MACHINERY | … · · 2010-10-10SINUMERIK 840D/810D/FM-NC...
User Documentation
SINUMERIK
840D/810D/FM-NC
SINUMERIK
Overview of SINUMERIK 840D/810D/FM-NC Documentation (12.98)
Brochure Catalog OrderingInfo NC 60.1 *)Technical Info.NC 60.2
Description of Functions Drive Functions *)
Description of Functions– Basic Machine *) – Extended Functions– Special Functions
SINUMERIK
611D840D/810D
SINUMERIK
840D/810D/FM-NC
840D/810D/FM-NC/611
Accessories
CatalogAccessories NC-Z
SINUMERIKSIROTECSIMODRIVE
840D/810DFM-NC
Lists *)Installation &Start-up Guide *)– FM-NC– 810D– 840D/611D– MMC
SINUMERIK
840D
Description ofFunctionsDigitizing
611D
SINUMERIK
SINUMERIK
840D/810D/FM-NC
Configuring KitMMC100/101– Configuring
Syntax – Development Kit
SINUMERIK
840D/810D/FM-NC
Screen KitMMC100/101SW Update andConfiguration
SINUMERIK
840D/810D/FM-NC
SINUMERIK
840D/810D
Operator Com-ponents(HW) *)
840D/810D/FM-NC
Description ofFunctionsSINUMERIKSafety Inte-grated
SINUMERIKSIMODRIVE
SINUMERIK
840D/810D/FM-NC611,Motors
SIMODRIVE
DOC ON CD *)The SINUMERIK System
General Documentation
Electronic Documentation
Manufacturer / Service Documentation
Manufacturer / Service Documentation
SINUMERIK
840D/810D/FM-NC
SINUMERIK
840D/810D
User Documentation
DiagnosticsGuide *)
Operator’s Guide– Unit
Operator Panel– HPU
AutoTurn– Short Guide– Programming (1)– Setup (2)
SINUMERIK
840D/810D/FM-NC
Program. Guide– Short Guide– Fundamentals *)– Advanced *)– Cycles– Measuring Cycles
Description ofFunctions– ManualTurn– ShopMill
Description ofFunctionsSynchronized ActionsWood, Glass,Ceramics
840D/810D
SINUMERIK
Operator’s Guide– ManualTurn– Short Guide ManualTurn– ShopMill– Short Guide ShopMill
840D/810D
Manufacturer / Service Documentation
SINUMERIK
840D/810D
Descr. of Functions– Computer Link– Tool Data
Information System
*) These documents are a minimum requirement for the control
Operator’sGuide– Short Guide– Operator’s
Guide *)
SINUMERIK
840D/810D/FM-NC
Configuring (HW) *)– FM-NC– 810D– 840D
SINUMERIK
SINUMERIK
840D/810D
SINUMERIK
840D/810D/FM-NC
Description ofFunctionsOperator InterfaceOP 030
Description ofFunctionsTool Manage-ment
SINUMERIKSIMODRIVE
SINUMERIKSIMODRIVE
SINUMERIKSIMODRIVE
SINUMERIKSIMODRIVE
SINUMERIKSIMODRIVE
840D611D
840D611D
Description ofFunctionsLinear Motor
SINUMERIKSIMODRIVESIROTEC
EMC Guide-lines
Manufacturer / Service Documentation
SINUMERIK
Description of FunctionsFanuc Programs for SINUMERIK
840D/810D
Description ofFunctionsHydraulicsModule
SINUMERIK 840D/810D/FM-NC
Short GuideOperation
12.98 Edition
Valid for
Control Software versionSINUMERIK 840D 5SINUMERIK 840DE (Export version) 5SINUMERIK 810D 3SINUMERIK 810DE (Export version) 3SINUMERIK FM-NC 3
SINUMERIK® documentation
Printing history
Brief details of this edition and previous editions are listed below.
The status of each edition is shown by the code in the "Remarks" column.
Status code in the "Remarks" column:
A .... New documentationB .... Unrevised reprint with new Order No.C .... Revised edition with new status.
If factual changes have been made on the page since the last edition,this is indicated by a new edition coding in the header on that page.
Edition Order No. Remarks
11.94 6FC5298-0AA10-0BP0 A04.95 6FC5298-2AA10-0BP0 C03.96 6FC5298-3AA10-0BP0 C08.97 6FC5298-4AA10-0BP0 C12.98 6FC5298-5AA10-0BP0 C
This manual is included in the documentation on CD-ROM (DOCONCD)Edition Order No. Remarks02.99 6FC5298-5CA00-0BG0 C
Further information is available on the Internet under:http://www.ad.siemens.de/sinumerik
This publication was produced with WinWord V 7.0 andDesigner V 4.0.
The reproduction, transmission or use of this document or itscontents is not permitted without express written authority.Offenders will be liable for damages. All rights, including rightscreated by patent grant or registration of a utility model or design,are reserved.
Other functions not described in this documentation might beexecutable in the control. This does not, however, represent anobligation to supply such functions with a new control or whenservicing.
Subject to change without prior notice.
© Siemens AG 1994 - 1998 All Rights Reserved.
12.98 General information
Siemens AG 1998. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
0-5
Introduction
MMC100.2
MMC103
Validity Unless stated otherwise, this operator’s guide applies tothe SINUMERIK 840D/810D and SINUMERIK FM-NCcontrols
How to use thisbooklet
This booklet is an operator’s guide describing all the mainprogramming steps.
The aim is to provide the operator with some quick help anda memory aid especially for commands that are usedinfrequently or to offer a quick reference on variousparameters.
This guide therefore has little text!
First familiarize yourself with the symbols below so that youunderstand them better whenever they occur on thefollowing pages.
The symbols
Gives you a tip or background information
Screen displays
Operation via softkeys
Input through the operator keyboard
Input through the machine control panel
General information 12.98
0-6 Siemens AG 1998 All rights reservedSINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
12.98 Contents
Siemens AG 1998. All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
0-7
List of Sections
Operator Control 1
Set-up 2
Manually Controlled Operation 3
Part Programming 4
Program Management 5
Automatic Mode 6
Alarms and Messages 7
Contents 12.98
0-8 Siemens AG 1998 All rights reservedSINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
Siemens AG 1998 All rights reserved. 1-9SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1. Operator Control
1.1 Key assignments slimline operator panel OP 031 1-10
1.2 Key assignments slimline operator panel OP 032 1-11
1.3 Key assignments operator panel 1-12
1.4 Key assignments external machine control panel 1-13
1.5 Graphical user interface 1-16
1.6 Operating areas 1-18
1.7 Operating principle 1-19
1. Operator Control 03.96
1-10 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.1 Key assignments slimline operator panel OP 031
MMC100.2
MMC103
A B C D E
F G H I J
7 (8 9 /
K L M N O1 2 3 - [
P Q R S T= 0 . + ]U
Z ? ! –
- < >
$
"
V W X Y,\
End
1..n
1 2 4 5 6 83
4 5 6 * )
7
1 Machine area key
2 Recall
3 Softkey bar (horizontal)
4 ETC key (menu extension)
5 Area changeover key
6 Softkey bar (vertical)
7 Alphanumeric key
8 Correction/cursor block with control keypad andInput key
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-11SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.2 Key assignments slimline operator panel OP 032
MMC100.2
MMC103
2 4 5 63
Q W E R T Y U I O P
Z X C V B N M ,
A S D F G H J K L
Ctrl Alt
Del
1..n
End
6 8 9
3 4 5
0 1 2
= / +
-
*
/
Del
7 98
10
1
1 Machine area key
2 Recall
3 Softkey bar (horizontal)
4 ETC key (menu extension)
5 Area changeover key
6 Softkey bar (vertical)
7 Alphablock
8 Correction/cursor block with control keypad and
Input key
9 Numeric block
10 Slot for PCMCIA adapter
1. Operator Control 03.96
1-12 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.3 Key assignments operator panel
MMC100.2
MMC103
Meaning of the key symbols:The keys marked with * correspond to the US layout.
1..n
GROUPCHANNEL *
Switch over channel
ALARMRESET *
Acknowledge alarm
Y
HELP *
Information
?NEXTWINDOW *
Select window
Move cursor
PAGEUP *
Page up
BACKSPACE
*
Delete character
Blank
SELECT *
Selection key/toggle key
INSERT
*
Edit/Undo
SHIFT
*
Shift
End of line
PAGEDOWN *
Page down
INPUT
*
Input (accept)
For keys with double assignments :
SHIFT *
Shift with key "Shift"
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-13SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.4 Key assignments external machine control panel
MMC100.2
MMC103
Machine control panel for turning machines
Machine control panel for milling machines
1 4 2 3 5 6 7 8
1 4 2 3 5 6 7 8
The keys marked with * correspond to the US layout.
1 Emergency stop pushbutton
2 Mode and machine functions
JOG
*
Jog
MDI
*
MDA
AUTO
*
Automatic
TEACH IN
*
Teach In
1. Operator Control 03.96
1-14 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.4 Key assignments external machine control panel
MMC100.2
MMC103
REPOS
*
Repos
REFPOINT
*
Ref
3 Incremental travel
4 Program control
RESET
*
Reset
SINGLEBLOCK
*
Single block
STOP
*
NC Stop
START
*
NC Start
5 Axis keys for turning machines
...
Axis keys (with direction)
RAPID
*
Rapid traverse override
WCSMCS
*
MCS/WCS
Axis keys for milling machines
X ...
9 Axis keys
...
Direction keys
RAPID
*
Rapid traverse override
WCSMCS
*
MCS/WCS
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-15SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.4 Key assignments external machine control panel
MMC100.2
MMC103
6 Spindle control
Spindle override
SPINDLESTOP
*
Spindle stop
SPINDLESTART
*
Spindle start
7 Feed control
Feed/rapid traverse override
FEEDSTOP
*
Feed stop
FEEDSTART
*
Feed start
8 Keyswitch
1. Operator Control 03.96
1-16 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.5 Graphical user interface
MMC100.2
MMC103
M0
M0
M0
H0.000000H0.000000
H0.000000
M0
M0
+ X 900.000 mm 0.000
- Y -156.000 mm 0.000
+ Z 230.000 mm 0.000
Auto
MDA
JOG
REPOS
REF
.
.
i
Machine Jog Channel resetProgram aborted 3
1
2
4
5
6
MCS Position Repos offset
11
13
11
Machine
16
Parameter Program
14
Services Diagnosis
G0 G91
Preselected tool: 11ç
Tool
ç
11
Feedrate mm/min
Actual 3000.00 0.0%Set 3000.00
1115
Auxiliary functions
78
9
12>
1017
1 Operating area
2 Channel status
3 Program status
4 Channel and mode group
5 Alarm and message line
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-17SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.5 Graphical user interface
MMC100.2
MMC103
6 Mode
7 Program name
8 Channel operational messages
9 Channel status display
10 Information relating to the menu bar
11 Work windows and NC displays
12 Dialog line with notes for operator
13 Focus
14 Horizontal softkey bar
15 Vertical softkey bar
16 Recall
17 etc.
1. Operator Control 03.96
1-18 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.6 Operating areas
MMC100.2
MMC103
The standard functions in the control are organized into thefollowing operating areas:
Operating areas
MACHINE
PROGRAM
SERVICES
DIAGNOSIS
START-UP
PARAMETERS
Executionof part programsmanual control
Developmentand adaptationof part programs
Reading in/outprograms and data
Alarm displays,service displays
Adaptation of NCdata to machine,system settings
Editingdata for programs/tool management
When you press the "Areachangeover" key, theoperating areas in the mainmenu appear in the horizontalsoftkey bar. You can use thiskey to switch from any menuto the main menu.
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-19SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
The MMC 100.2 and MMC 103 provide a range of key andsoftkey assignments which have the same function in alloperating areas and menus.
Area changeover:
Switch back from anymenu to the main menu ofyour control.
Softkeys:
Horizontal softkeys:These keys subdivide eachoperating area into furthermenu levels. Each horizontalmenu item has a verticalmenu bar/softkeyassignment.
Vertical softkeys:Assigned with functions forthe currently selectedhorizontal softkeys.
1. Operator Control 03.96
1-20 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
Navigation in the menu window:
? Change menu windows:Change the focus to theselected menu window.
Scroll in the menu window:Scroll one screen page downor up.
!
Position cursor in the menuwindow:Position the cursor at thedesired point in the menuwindow.
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-21SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
Navigation in the directory tree:
!
Select directory/file:Position the cursor on thedesired directory/file.
Open/close directory:Open or close the selecteddirectory.
Open file:Open the desired file, e.g. ifyou want to edit the file in theASCII editor (in this case theeditor is openedautomatically).
Select file (MMC103):Select the desired file.
Select several files(MMC103):Hold down the "Shift" and"Cursor Down" keys.
Select start of block.
! or
Neighboring files are selectedwhen you hold down the"Cursor Up" or "Cursor Down"keys.
Deselect selected files.
Cancel all selections.
1. Operator Control 03.96
1-22 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
Edit inputs/values:
If you want to editinputs/values, thecorresponding key is alwaysdisplayed automatically onthe right of the input field. Thefollowing input fields areavailable:
1. Option fields (radiobuttons or check boxes):Activate or deactivate theoption field.
2. Input fields:Switch to input mode.
Enter the value or word (e.g.file name, type, etc.) on thenumeric keypad.
You automatically switch toinput mode if you first positionthe cursor on the input field.
Always confirm your inputwith the "Input" key. Thevalue is accepted.
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-23SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
You can use the "Toggle" keyto select one of severaldefault values.
3. Selection list (MMC 103):Display the preselection ofpossible values.
Open selection list
!
Position the cursor on thedesired values.
Always confirm your inputwith the "Input" key. Thevalue is accepted.
Switch to the next value in theselection list withoutdisplaying the entire list.
1. Operator Control 03.96
1-24 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
Confirm/cancel input:
OKConfirm input:Save the inputs and exit thecurrent menu (youautomatically return to thecalling menu).
CancelCancel input:Reject the inputs and quit thecurrent menu (youautomatically return to thecalling menu).
Reject the inputs and quit thecurrent menu (youautomatically move up onelevel).
Clear the current input butremain in the current menu.
03.96 1. Operator Control
Siemens AG 1998 All rights reserved. 1-25SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
1.7 Operating principle
MMC100.2
MMC103
Operation with the mouse:
If you have installed a mouse,operation is facilitated asfollows:
1 "click" 1 click means:• Activate the menu window.• Position the cursor on the
desired input field.• Select directory.• Activate softkey.• Activate/deactivate radio
button/check box.• Activate input field.• Open selection list.
2 "clicks" 2 clicks mean:• Accept value/input.• Open directory.
1. Operator Control 03.96
1-26 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
Siemens AG 1998 All rights reserved. 2-27SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2. Set-up
2.1 Approach reference point 2-28
2.2 Enter tool offsets 2-29
2.3 Calculate tool offsets 2-30
2.4 Enter/alter zero offset (MMC100.2) 2-31
2.5 Enter/alter zero offset (MMC103) 2-32
2.6 Scratching method/determine zero offset (MMC100.2) 2-34
2.7 Scratching method/determine zero offset (MMC103) 2-35
2.8 Program the setting data 2-36
2. Set-up 03.96
2-28 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.1 Approach reference point
MMC100.2
MMC103
Caution:Position the axes if they are not already located at a safeposition.Always follow the axis movements directly on the machine.Ignore the actual value display as long as the axes are notreferenced (the software limit switches are not effective).
MachineSelect "Machine"operating area.
Jog or
MDAChoose "Jog" or "MDA".
Select "Ref" machinefunction.
...
Turning machine:Traverse axes.
X ...
9Milling machine:Select axes and
...
traverse axes.
Stop axis before referencepoint is reached.
03.96 2. Set-up
Siemens AG 1998 All rights reserved. 2-29SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.2 Enter tool offsets
MMC100.2
MMC103
ParameterSelect "Parameter"operating area.
Tooloffset
Select "Tool offset" menu.
Choose the desiredfunction:
T no.+
T no.-
Select tool (T no.).
D no.+
D no.-
Select tool edge (D no.).
Delete– Delete tool/tool edge
Go to– Find tool
Overview...List existing tools.
New...Create new tool/tool edge.
Enter the new values.
2. Set-up 03.96
2-30 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.3 Calculate tool offsets
MMC100.2
MMC103
ParameterSelect "Parameter"operating area.
Tooloffset
Select "Tool offset" menu.
Position cursor on desiredtool parameter.
Determinecompensa.
Select axis and enterreference value.
CalculateThe current position and thereference value of theselected tool parameter arecalculated automatically.
03.96 2. Set-up
Siemens AG 1998 All rights reserved. 2-31SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.4 Enter/alter zero offset (MMC100.2)
MMC100.2
ParameterSelect "Parameter"operating area.
Zerooffsets
Select "Zero offsets" menu.
OverviewSelect zero offsets:• settable• active settable• active programmable• sum of active ones• external ones• basic offsets
Position the cursor on thedesired field and enter/alterthe value, or
use the "Toggle" key tochoose a new value.
SaveSave the values.
2. Set-up 03.96
2-32 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.5 Enter/alter zero offset (MMC103)
MMC103
ParameterSelect "Parameter"operating area.
Zerooffset
Select "Overview of settablezero offsets" menu.
Axes +
Axes -
Select zero offset:Changes to the defined zerooffsets of the next or previousaxis.
Offsets
Rotation,scal., mirr.
Change display mode of thecurrently displayed zerooffset. The display showseither the absolute offsets orthe proportional values ofrotation, scaling or mirroring.
Enter/change zero offset:
Basic ZOsDisplay all the defined basiczero offsets.
Sett. ZOsDisplay all the definedsettable zero offsets.
03.96 2. Set-up
Siemens AG 1998 All rights reserved. 2-33SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.5 Enter/alter zero offset (MMC103)
MMC103
Position the cursor on thedesired field and enter/alterthe value.
Please note:Changes in the zero offset are updated at entry.
2. Set-up 03.96
2-34 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.6 Scratching method/determine zero offset (MMC100.2)
MMC100.2
ParameterSelect "Parameter"operating area.
Select "Jog" mode.
Zerooffsets
Select "Zero offsets" menu.
DetermineZO
"Determine ZO (scratching)"window, enter• the tool (T no.),• the tool edge (D no.),• the corresponding length
parameters (1, 2, 3) andthe direction(+, −, none),
• the allowance and directionof the radius(+, −, none),
• the allowance and directionof a user-definable offset(+, −, none).
You can select values usingthe "Toggle" key.
Traverse axes (scratching).
OKWith "OK" all the values areentered into the selected zerooffset.
03.96 2. Set-up
Siemens AG 1998 All rights reserved. 2-35SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.7 Scratching method/determine zero offset (MMC103)
MMC103
MachineSelect "Machine" operatingarea.
ScratchingActive level, active zero offsetand active tool are selected.
! Select axis which shall betraversed, with the cursor.
or X
Traverse axis to theworkpiece, enter desired setposition and confirm with"Input". The offset iscalculated.
OKWith "OK" all the values areentered into the selected zerooffset.
Please note:The calculation of the offset always refers to the currentworkpiece coordinate system (WCS).
In order to take account of thetool geometry, position thecursor in the column"Geometry + wear" on theaxis which shall be traversedand select with "Toggle" key,how the tool offset shall becalculated.
2. Set-up 03.96
2-36 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.8 Program the setting data
MMC100.2
MMC103
ParameterSelect "Parameter"operating area.
Settingdata
Select the "Setting data"menu.
Define operating statesusing setting data:
Work arealimit.
• Change working arealimitation.
Jogdata
• Change jog data.
Spindledata
• Change spindle data.
FeedrateDRY
• Change dry run feedrate forDRY test mode.
Startingangle
• Change starting angle forthread cutting.
Misc.• Display miscellaneous
setting data.
Protectionzones
• Choose level for protectionzone.
03.96 2. Set-up
Siemens AG 1998 All rights reserved. 2-37SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
2.8 Program the setting data
MMC100.2
MMC103
!
Position the cursor on thedesired field and change thevalue, or
select a new value using the"Toggle" key.
2. Set-up 03.96
2-38 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
Siemens AG 1998 All rights reserved. 3-39SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition
3. Manually Controlled Operation
3.1 Jog/Jog-Inc mode 3-40
3.2 MDA mode 3-42
3.3 Teach In mode 3-43
3. Manually Controlled Operation 03.96
3-40 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition
3.1 Jog/Jog-Inc mode
MMC100.2
MMC103
MachineSelect "Machine"operating area.
JogSelect "Jog" mode.
"Reference point approach" is deactivated.
...
Turning machine:Traverse axes.
X ...
9
Milling machine:Select axis and
traverse.
The traversing velocity is stored in the "setting data".
If necessary, use the overrideto set the velocity.
If necessary, move axes withrapid traverse.
03.96 3. Manually Controlled Operation
Siemens AG 1998 All rights reserved. 3-41SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition
3.1 Jog/Jog-Inc mode
MMC100.2
MMC103
Select/enter incrementvalue for traversingposition ("Inc"):
...
Traverse axes in definedincrements, or
Incenter the desired increment.
Traverse axis with theentered increment.
3. Manually Controlled Operation 03.96
3-42 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition
3.2 MDA mode
MMC100.2
MMC103
MachineSelect "Machine"operating area.
MDASelect "MDA" mode.
In "Teach In" mode, it is only possible to insert blocks atpoints in the program which have not yet been executed.
Enter NC block (one orseveral consecutive programblocks).
Confirm input.
Execute NC block.
MDA-Prog.sichern
Save program in MDA buffer.
If no program name is entered, the program is automaticallystored in the MDA buffer with the name OSTORE.MPF(MMC100.2) or MDAX.MPF (MMC103).
03.96 3. Manually Controlled Operation
Siemens AG 1998 All rights reserved. 3-43SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition
3.3 Teach In mode
MMC100.2
MMC103
MachineSelect "Machine"operating area.
MDASelect "MDA" mode.
Select "Teach In" submode.
In "Teach In" mode, it is only possible to insert blocks atpoints in the program which have not yet been executed.
1. Manual positioning:
...
Turning machine:Traverse axes.
X ...
9
Milling machine:Select axis and
...
traverse.
The axis name and the traversed path are displayed in the"Teach In program" window.
3. Manually Controlled Operation 03.96
3-44 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810DFM-NC Short Guide Operation (BAK) - 12.98 Edition
3.3 Teach In mode
MMC100.2
MMC103
2. Manual input of coordinates:
• Enter coordinates oftraversing positions and
• enter additional functions(preparatory conditions,miscellaneous functions,etc.) in the "MDA program"window.
MMC100.2
Deleteblock
Delete the current block.
Insertblock
Insert an empty line beforethe current block.
Saveblock
Save new axis positions andadditional functions.
Executed the enteredprogram blocks and displaythem in the current blockwindow.
MMC103Enter and delete blocks onkeyboard.Positions are automaticallysaved at entry.
Siemens AG 1998 All rights reserved. 4-45SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4. Part Programming
4.1 Select/enable workpiece/part program 4-46
4.2 Open/edit part program 4-47
4.3 Create new workpiece/part program 4-49
4.4 Execute workpiece/part program 4-50
4.5 Copy/paste, rename, delete, enable 4-51
4.6 Load/unload program (MMC 103) 4-53
4. Part Programming 03.96
4-46 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.1 Select/enable workpiece/part program
MMC100.2
MMC103
ProgramSelect "Program"operating area.
Select workpiece/part program:
Work-pieces
Select the level:• Workpieces
Partprograms
• Part programs
Sub-routines
• Subroutines
Standardcycles
• Standard cycles(MMC100.2)
Usercycles
• User cycles
Clip-board
• Clipboard
Position the cursor on thedesired file in the directorytree.
03.96 4. Part Programming
Siemens AG 1998 All rights reserved. 4-47SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.2 Open/edit part program
MMC100.2
MMC103
ProgramSelect "Program"operating area.
Open part program:
Position the cursor on thedesired file in the directorytree.
Open program in ASCIIeditor:
Press the "Input" key.
Activate interactiveprogramming (MMC103):
Interactiveprogr.
Press softkey "Interactiveprogr.".
4. Part Programming 03.96
4-48 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.2 Open/edit part program
MMC100.2
MMC103
Edit part program:
OverwriteToggle between insert andoverwrite mode.
Markblock
Mark the beginning of block.
Copyblock
Save the block in theClipboard.
Deleteblock
Delete block.
Insertblock
Paste the block from theClipboard.
Search/go to ...
Position on block no.,beginning of file, end of file orsearch string.
Search
Enter search string.
Substitute
Enter substitute.
Continuesearch
Next occurrence of searchstring.
Go to ...
Enter block no.
Savefile
Save part program.
Closeeditor
Close text editor.
03.96 4. Part Programming
Siemens AG 1998 All rights reserved. 4-49SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.3 Create new workpiece/part program
MMC100.2
MMC103
ProgramSelect "Program"operating area.
Work-pieces
Partprograms
Sub-routines
Select "Workpieces", "Partprograms" or "Subroutines".
Open directory.
New ...Enter name of workpiece,main program or subroutineand
select "File type".
MMC103:Select key• text editor• activate interactive
programming.
4. Part Programming 03.96
4-50 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.4 Execute workpiece/part program
MMC100.2
MMC103
ProgramSelect "Program" operatingarea.
Work-pieces
Select workpiece:
Mark the desired workpiecewith the cursor in theworkpiece overview.
Selection
Select the workpiece.
Partprograms
Select part program:
Mark the desired workpiecewith the cursor in the partprogram overview.
SelectionSelect the part program.
Start the workpiece/partprogram.
Clip-board
You can also run partprograms directly from theClipboard.
03.96 4. Part Programming
Siemens AG 1998 All rights reserved. 4-51SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.5 Copy/paste, rename, delete, enable
MMC100.2
MMC103
ProgramSelect "Program"operating area.
Select the level and positionthe cursor on the desired filein the directory tree.
Manageprograms
MMC103:Select "Manage programs".
Copy/paste program:
CopySelect the source file.
PasteSave the source file in thetarget directory.
If necessary, use the "Toggle"key to select the file type.
Rename the program:
RenamePress the "Rename" softkeyand enter new name.
Use the "Toggle" key toselect the file type.
4. Part Programming 03.96
4-52 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.5 Copy/paste, rename, delete, enable
MMC100.2
MMC103
Delete program:
DeleteDelete the program from thedirectory.
Change enable:
Changeenable
Set (x) or cancel ( ) enable.
03.96 4. Part Programming
Siemens AG 1998 All rights reserved. 4-53SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
4.6 Load/unload program (MMC 103)
MMC103
ProgramSelect "Program" operatingarea.
Position the cursor on thedesired file in the directorytree.
LoadLoad the program into theCNC memory.
UnloadSave the program to harddisk.
Please note:When you activate "Load", the program is automaticallydeleted from the hard disk. When you activate "Unload", theprogram is automatically cleared from the CNC memory.
4. Part Programming 03.96
4-54 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
Siemens AG 1998 All rights reserved. 5-55SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5. Manage data
5.1 Transfer data (MMC 100.2) 5-56
5.2 Transfer data (MMC 103) 5-59
5.3 Create new file/directory (MMC 103) 5-61
5.4 Load/unload program (MMC 103) 5-62
5.5 Copy/paste, delete (MMC 103) 5-63
5.6 Directory/file/archive properties (MMC 103) 5-64
5. Manage data 03.96
5-56 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.1 Transfer data (MMC 100.2)
MMC100.2
ServicesSelect "Services"operating area.
Read out data:
Data outSelect "Data out" menu.
Select interface:
V.24-user
• V.24 user
V.24-printer
• V.24 printer
V.24-PG/PC
• V.24-PG/PC
Position the cursor on thedesired file in the directorytree.
StartStart "Data out".
StopInterrupt "Data out".
03.96 5. Manage data
Siemens AG 1998 All rights reserved. 5-57SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.1 Transfer data (MMC 100.2)
MMC100.2
Read in data:
Data inSelect " Data in" menu.
Select interface:
V.24user
• V.24 user
V.24-PG/PC
• V.24-PG/PC
Position the cursor on thedesired file in the directorytree.
5. Manage data 03.96
5-58 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.1 Transfer data (MMC 100.2)
MMC100.2
StartOrganize data according tothe existing path:
Path/workpiece from archivefile
Store all files in the directory,irrespective of archived path:
Path/workpiece from archivefile
Store all files in the Clipboard,irrespective of archived path:
Read into the Clipboard
OKStart "Data in".
StopInterrupt "Data in".
03.96 5. Manage data
Siemens AG 1998 All rights reserved. 5-59SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.2 Transfer data (MMC 103)
MMC103
ServicesSelect "Services"operating area.
Read out data:
Data outSelect "Programs/data"menu.
Select data in the directorytree.
Select target area:
V.24• V.24 interface
PG• Programming device
Diskette...• Diskette drive
Archive...• "Archive" on hard disk
NC Card• NC Card
Start transfer:
StartInitiate data transfer ondisk/archive (softkey labelchanges to "Stop").
5. Manage data 03.96
5-60 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.2 Transfer data (MMC 103)
MMC103
Read in data:
Data inSelect "Programs/data"menu.
Select data in the directorytree.
Select source area:
V.24• V.24 interface
PG• Programming device
Diskette...• Diskette drive
Archive...• "Archive" on hard disk
NC Card• NC Card
Start transfer:
StartInitiate data transfer ondisk/archive (softkey labelchanges to "Stop").
The data transfer is initiated automatically. You caninterrupt data transfer at any time by pressing the softkeyagain.
03.96 5. Manage data
Siemens AG 1998 All rights reserved. 5-61SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.3 Create new file/directory (MMC 103)
MMC103
ServicesSelect "Services" operatingarea.
Managedata
Select "Manage data" menu.
New...Enter program name andselect type of program.
By selecting the "End"softkey, you can switchbetween the areas "Name"and "Type of file".
OKNew file/directory will becreated.
5. Manage data 03.96
5-62 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.4 Load/unload program (MMC 103)
MMC103
ServicesSelect "Services"operating area.
Managedata
Select "Manage data" menu.
Position the cursor on thedesired file in the directorytree.
LoadLoad the file from the harddisk into the CNC memory.
UnloadUnload the file from the CNCmemory to the hard disk.
03.96 5. Manage data
Siemens AG 1998 All rights reserved. 5-63SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.5 Copy/paste, delete (MMC 103)
MMC103
ServicesSelect "Services"operating area.
Managedata
Select "Manage data" menu.
Position the cursor on thesource file in the directorytree.
Copy/paste program:
CopySelect target directory.
Programsdata
Close target window.
PasteCopy source file to targetdirectory.
ClipboardCopy to or from Clipboard.
DisketteCopy to or from diskette.
Delete program:
DeleteDelete selected file.
5. Manage data 03.96
5-64 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
5.6 Directory/file/archive properties (MMC 103)
MMC103
ServicesSelect "Services"operating area.
Managedata
Select "Manage data" menu.
Position the cursor on thedesired file in the directorytree.
PropertiesSelect "Properties" menu.
• Rename file• Convert file type• Change access rights for
file/directory• Display contents of all files
The access level can only be changed with the appropriateaccess rights.
Siemens AG 1998 All rights reserved. 6-65SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6. Automatic Mode
6.1 Select workpiece/program 6-66
6.2 Start/stop/cancel program 6-67
6.3 Repos − Reposition after interruption 6-68
6.4 Overstore 6-70
6.5 Display program level 6-71
6.6 Program correction 6-72
6.7 Execution from V.24 (MMC 100.2) 6-73
6.8 Load/unload program from hard disk (MMC 103) 6-74
6.9 Execution from hard disk (MMC 103) 6-75
6. Automatic Mode 03.96
6-66 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.1 Select workpiece/program
MMC100.2
MMC103
MachineSelect "Machine"operating area.
AUTOSelect "Automatic" mode.
Programoverview
Select "Program overview"menu.
Work-pieces
Partprograms
Select desired workpiece/partprogram with the cursor in theworkpiece/part programoverview.
Selection
Select workpiece/partprogram.
Changeenable
Set (x) or cancel ( ) enable.
03.96 6. Automatic Mode
Siemens AG 1998 All rights reserved. 6-67SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.2 Start/stop/cancel program
MMC100.2
MMC103
MachineSelect "Machine"operating area.
AUTOSelect "Automatic" mode.
Please check that:No alarms are active.The program is selected.The feed enable is active.The spindle enable is active.
Start part program.
Stop part program.
Cancel part program.
A part program which has been interrupted by "NC Stop"can be resumed with "NC Start".
A part program which has been interrupted by "Reset" runsfrom the start when you press "NC Start".
6. Automatic Mode 03.96
6-68 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.3 Repos − Reposition after interruption
MMC100.2
MMC103
After a program interrupt ("NC Stop") you can move the toolaway from the contour in the manual mode. The controlsaves the coordinates of the interruption point. Thetraversed path differences of the axes are displayed.
MachineSelect "Machine"operating area.
JogSelect "Jog" mode.
Reposition after programinterruption.
Turning machine:
...
Traverse axes up to the pointof interruption.
Milling machine:
X ...
9 Select axis and
...
traverse axes up to theinterruption point.
Caution:Travel beyond the interruption point is inhibited. The feedoverride switches are active.
03.96 6. Automatic Mode
Siemens AG 1998 All rights reserved. 6-69SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.3 Repos − Reposition after interruption
MMC100.2
MMC103
MachineSelect "Machine"operating area.
AUTOSelect "Automatic" mode.
Continue machining.
6. Automatic Mode 03.96
6-70 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.4 Overstore
MMC100.2
MMC103
MachineSelect "Machine"operating area.
AUTOSelect "Automatic" mode.
Overstore with singleblock:The program automaticallystops at the next blockboundary.
Overstore without singleblock:Stop part program.
OverstoreEnter the values andfunctions to be executed.
Run the entered block.
03.96 6. Automatic Mode
Siemens AG 1998 All rights reserved. 6-71SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.5 Display program level
MMC100.2
MMC103
MachineSelect "Machine"operating area.
AUTOSelect "Automatic" mode.
Programlevel
Display block numbers formain programs andsubroutines with therespective pass counts (P).
Currentblock
Display the blocks of thecurrent program.
Pressing the "Program level" softkey automatically changesthe level to and from "current block".
6. Automatic Mode 03.96
6-72 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.6 Program correction
MMC100.2
MMC103
MachineSelect "Machine"operating area.
AUTOSelect "Automatic" mode.
The control has detected a system error in the partprogram. Execution of the part program is automaticallyinterrupted.
Correctprogram
Correct the program blockwith the error.
Continue machining.
03.96 6. Automatic Mode
Siemens AG 1998 All rights reserved. 6-73SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.7 Execution from V.24 (MMC 100.2)
MMC100.2
MachineSelect "Machine"operating area.
Programoverview
Select "Program overview"menu.
Executionfrom extern.
Select "Execution fromexternal source" menu.
Position the cursor on thedesired file in the directorytree.
Start execution from V.24.
Executed blocks appear inthe current block window.
Alternatively, it is possible to start execution in the"Services" operating area.You can change the transfer parameters in the "Services"operating area. The transfer is recorded in the error log.
6. Automatic Mode 03.96
6-74 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.8 Load/unload program from hard disk (MMC 103)
MMC103
MachineSelect "Machine"operating area.
Programoverview
Select "Program overview "menu.
Position the cursor on thedesired file in the directorytree.
LoadLoad the program into theCNC memory.
UnloadSave the program on the harddisk.
Please note:When you activate "Load", the program is automaticallydeleted from the hard disk. When you activate "Unload", theprogram is automatically cleared from the CNC memory.
03.96 6. Automatic Mode
Siemens AG 1998 All rights reserved. 6-75SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
6.9 Execution from hard disk (MMC 103)
MMC103
MachineSelect "Machine"operating area.
Programoverview
Select "Program overview"menu.
Position the cursor on thedesired file in the directorytree.
Press the "NC Start" key.
Executionfr. hard disk
Start/cancel read-in andexecution.
The program remains stored with "Execution from harddisk".
6. Automatic Mode 03.96
6-76 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
Siemens AG 1998 All rights reserved. 7-77SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
7. Alarms and Messages
7.1 Alarms/messages 7-78
7. Alarms and Messages 03.96
7-78 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
7.1 Alarms/messages
MMC100.2
MMC103
DiagnosisSelect "Diagnosis"operating area.
Display alarms:
AlarmsDisplay alarms with "alarmnumber", "date","explanation" and "cancelcriterion".
Delete alarm:
Switch the control off and onagain.
Press "Reset".
Press "Acknowledge alarm".
Alarm is canceled with "NCStart".
Alarm is canceled with"Recall".
03.96 7. Alarms and Messages
Siemens AG 1998 All rights reserved. 7-79SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
7.1 Alarms/messages
MMC100.2
MMC103
Display messages:
MessagesDisplay PLC error messagesand PLC operationalmessages.
Caution:PLC error messages must always be acknowledged.
Display alarm log:
Alarmlog
Display complete log ofalarms and messages whichhave occurred.
Displaynew
Update alarm log.
MMC 103:
AcknowledgeMMC alarm
Select and delete MMCalarm.
7. Alarms and Messages 03.96
7-80 Siemens AG 1998 All rights reserved.SINUMERIK 840D/810D/FM-NC Short Guide Operation (BAK) - 12.98 Edition
SIEMENS AGA&D MC IS
Suggestions
Corrections
P.O. Box 3180
D-91050 ErlangenFederal Republic of Germany
for Publication/Manual
SINUMERIK 840D/810D/FM-NC
(Fax ++49 9131/98-1145) User Documentation
From
Name
Short GuideOperation
Order No.: 6FC5298-5AA10-0BP0Edition: 12.98
Company/Department
Address_____________________________________
_____________________________________Telephone: /_____________________________________Telefax: /
Should you come across any printingerrors when reading this publication,please notify us on this sheet.Suggestions for improvement are alsowelcome.
Suggestions and/or corrections