Self-Install Aruba Wireless Access Point Ver. 17 › docs › Self-Install...Self-Install Aruba...
Transcript of Self-Install Aruba Wireless Access Point Ver. 17 › docs › Self-Install...Self-Install Aruba...
1
Self-Install Aruba Wireless Access Point
Ver. 17
Table of Contents Contact Support Numbers ...................................................................................................................................................... 1
Section A: Items Needed ..................................................................................................................................................... 1
Section B: Package Contents ............................................................................................................................................... 2
Section C: Optional Desktop Mount ................................................................................................................................... 3
Section D: Mounting Hardware Install ................................................................................................................................ 4
Section E: Connecting Hardware......................................................................................................................................... 5
Section F: Powering up and Connecting Wireless Devices ................................................................................................. 7
Section G: Self-Install Testing and Acceptance Form .......................................................................................................... 8
Section H: Troubleshooting Guide ...................................................................................................................................... 9
Addendum 1: Testing 911 ................................................................................................................................................. 10
Contact Support Numbers 1. Installation Support 440-202-4502, Option 1
Business Days, Monday – Friday (8am - 8pm ET)
Section A: Items Needed
Phillips Screwdriver Pencil Torx T8H Screwdriver “Only needed for Desktop Mount Option”
2
Section B: Package Contents
Aruba Access Point Aruba Mount Plate Power Adapter 4G USB Modem
Short Black Cable Yellow Cable Surface Mount Box
2 Drywall anchors w/screws
2 machine screws
Cisco ATA Phone Adapter Black Cable
Power Adapter
Items for “Phone Option Install Only”
Hardware Included
1 Phillips head screw
2 T8H Torx Security
Screws (optional use)
Items for “Desktop Mount Option Only”
3
Section C: Optional Desktop Mount
1. If NOT using “Optional Desktop Mount” Skip to section D: Mounting Hardware Install 2. The Optional Desk Mount Kit is a stand-alone mount for the Aruba access point,
which allows the cables route out the bottom rear of the AP when the desk mount is attached to the AP.
3. Set the mount base on a flat surface, aligning the circular cutout at the top, with the corresponding indentation at the bottom of the AP housing. Attach the two pieces by pressing the AP back cover onto the base.
4. Turn the mount upside down and insert the 7mm Phillips head screw into the hole at the center of the base, then tighten until the AP back cover is securely fastened to the base.
5. Connect the Short Black cable to the back of Aruba AP. 6. Match the slots on the back of the access point with the
corresponding posts on the AP back cover. 7. Press the AP into the cover then pull down gently until the
posts lock into place.
8. (Optional) Insert the two 12mm T8H Torx security screws into the holes on the back of the base, as indicated, then tighten until the AP is firmly anchored into the AP back cover.
9. Go to Section E: Connecting Hardware
Short Black
cable
4
Section D: Mounting Hardware Install
1. Installing the Surface mount Box to Wall (If not Mounting to Wall skip to step 3) a. Lay box on mounting surface, leave 6 inches of space on all four sides
and mark 2 holes for anchors with pencil.
b. Install the Drywall anchors where the pencil marks were made in step 1a c. Then attach Surface mount box to wall with two Anchor screws
2. Mount Aruba Back Plate to Surface mount Box using two machine screws making sure, the up arrow is facing up and out on back plate
3. Connect the Short Black cable to the back of Aruba AP.
4. Attach Aruba AP to back plate by lining up The holes and posts, push in then down to Lock into place
Black cable
5
Section E: Connecting Hardware
1. Attach USB Cellular Modem to USB Port on the right side of
Aruba AP. USB port is marked with this Icon
NOTE: Please make sure these devices are located in a secure place to prevent removal. Should the USB modem be removed, Acuative will be alerted and the devices will be disabled and reported to the service provider.
2. Locate your Cable or DSL Modem from your Internet Provider.
(see examples at right for multi and single port modems)
a. If cable or DSL modem is Multi-port type go to step 3.
b. If cable or DSL modem is single port type go to step 6.
3. Connect Yellow cable to the Aruba AP Black Port labeled E0
4. Connect the other end to the cable or DSL
modem “LAN” port
5. Go to step 8
6. Connect Yellow cable to the Aruba AP Black Port labeled E0
7. Connect the other end to existing Network Switch
a. To help identify the network switch look
where cash registers and all other network
devices are connected as they would be
connected to the network switch
b. (see example at right of Aruba AP connected
to a Network switch)
Multi-port Modem
Single port Modem
Aruba AP Bottom View
Multi-port Modem
Aruba AP Bottom View
Network Switch
ONLY CONNECT THE DISCRIBED HARDWARE TO THE ARUBA (No Printers, No Surveillance systems)
ONLY CONNECT THE DISCRIBED HARDWARE TO THE ARUBA (No Printers, No Surveillance systems)
6
8. Locate the network cable in rear of Cash Register
a. Network cable looks same as supplied yellow cable with same type of connectors
but may differ in color
b. See example at right of cable end connectors to help identify
c. Leave network cable connected to rear of cash register, disconnect other end and
connect it to the Aruba AP Blue port labeled E1
d. If a second Register exists connect to Blue port labeled E2
IF NO Analog Telephone Adapter is being installed YOU ARE COMPLETE ON CONNECTING
HARDWARE GOTO Section F:
9. Cisco SPA122 Analog Telephone Adapter (“Phone Option Install”)
a. Connect supplied BLACK cable to Blue INTERNET port on ATA
device
b. Connect other end of cable Aruba AP RED port labeled E3
c. Connect phones to ATA White phone ports 1 & 2
d. Connect Power Adapter to ATA device in port labeled POWER
then plug into electrical outlet.
10. Forwarding your current Main phone number to IVR number.
a. IVR Line number should be on ATA. If not located call
Implementation for IVR number to forward to.
b. Call your current phone provider for Instructions if line
forwarding is not locally available. (see example below)
Some lines can be forwarded by dialing on a phone attached to the line you
want to forward: DO NOT CONNECT THE ATA UNTIL STEP #3
1. Dial *73
2. 872 ###-###-####, then Hang up (replace ### with IVR number)
3. NOW CONNECT THE ATA
4. Test the IVR by calling your main number and verify phone connects
through the ATA
“If this does not work at your site, Please call Installation Support 440-202-4502, Option 1 - Business Days, Monday – Friday (8am - 8pm ET)”
Black Cable
Aruba Blue port E1 Aruba Blue port E2 (If Second Register)
ONLY CONNECT THE DISCRIBED HARDWARE TO THE ARUBA (No Printers, No Surveillance systems)
7
Section F: Powering up and Connecting Wireless Devices
1. Connect the power adapter to the Aruba AP power port on the right side then plug the Power adapter into an
electrical outlet.
2. Wait for the Aruba AP to come Online. The System
Status light will flash GREEN while the Aruba boots up
and will turn solid Amber when system is Ready.
3. Two separate networks should be visible to connect
your Wireless devices.
Wireless Kiosk
Wi-Fi SSID
Subway_Corp
Subway_Guest
ONLY CONNECT THE DISCRIBED HARDWARE TO THE ARUBA (No Printers, No Surveillance systems)
8
Section G: Self-Install Testing and Acceptance Form
After all hardware has been installed and Powered up use the check off/acceptance Form for validating and troubleshooting.
Wi Fi Testing:
Connect a device to the Subway_Corp SSID and verify Internet access
Connect a device to the Subway_Guest SSID and verify Internet access
Phone Testing: (Only required with Analog Telephone Adapter (ATA) install)
Call Store Main number from outside line to verify Inbound call received through ATA device
Make Outbound call from ATA connected phone to verify ATA device
Test your 911 service. Please refer to the addendum 1: Testing your 911 Service Fail-Over test. The purpose of the fail over test is to verify that in the event the main circuit fails the network will fail over to the 4G cellular circuit.
Remove the Yellow cable from the Aruba AP Black Port Labeled E0
Observe the System status LED. After a few minutes, it should go to a flashing Green then back to a Solid Amber. (on 4g failover)
Repeat Wi Fi testing from above, Subway_Corp o NOTE: Subway_Guest should display “Unable to Connect to captive portal” o Repeat phone testing from above (only required with ATA install)
After tests are complete reconnect Yellow cable to Aruba AP in the Black port labeled E0 and observe the System status LED. After a few minutes, it should start flashing Green then go to a solid Amber. At that point you are back on Main Network Circuit. If all tests are complete, fill out checklist. If any Issues, follow troubleshooting guide on page 2 then if needed call Acuative Support for assistance in testing at (440) 202-4502
Final Testing Check Off List YES NO NA
1. All Hardware Installed and connected
2. Solid Amber on System status LED
3. Test Internet (Wi Fi)
a. Test Subway_Corp SSID for Internet
b. Test Subway_Guest SSID for Internet
c. Test Forwarded Phone Line (ATA Install Only)
4. Was main phone line forwarded to IVR number
a. Inbound call received from ATA attached Phone
b. Outbound call made from ATA connected phone
5. Fail Over Test
6. Complete test of 911 (see addendum)
9
Call Acuative immediately if any equipment is missing otherwise you may be charged a fee for replacements
Section H: Troubleshooting Guide
Post Installation Support 440-202-4502, Option #2
Anytime, 24 x 7 x 365
Table 2
Aruba AP System Status LED Solid Amber?
Yes No
Test Wi Fi Complete?
Yes No
Check Yellow Cable from Modem to Black Port
on Aruba Labeled E0. Reconnect or Power
Cycle Modem if needed. Wait 2-8 minutes.
System Status LED Solid Amber?
Yes No
Call Acuative Support
(440) 202-4502
ATA device installed?
No Yes
Test Inbound call from
Outside line and
Outbound Call through
ATA connected phone
Did calls complete?
Yes No
Verify Black cable connection from ATA Internet port to Aruba Red Port labeled E3. Verify LEDs with Table 2.
Did Test Complete? Yes No
Testing Complete
10
Addendum 1: Testing 911
TESTING YOUR 911 SERVICE
Placing 933 Test Calls
933 is a courtesy text to speech service offered by IntelePeer as part of your 9-1-1 package. When an end user dials 933, it will play back the phone number and address that is provisioned. This service is used as part of the 9-1-1 testing performed during the onboarding process prior to the live 9-1-1 calls, and is used primarily to test connectivity to the emergency IPs for 9-1-1 service. Secondarily, it tests to ensure the provisioned address broadcasts appropriately.
When your port order is first entered into the system, your Emergency Services Address will be associated to your number(s). Upon Completion of the porting request, when your numbers are active, the Emergency service location should take approximately 60 minutes to complete as it uploads the information into the national database. Please do not attempt to test the service within the first 60 minutes of being live. Calls to 911 are labeled as an Un-provisioned call from a DID without an address associated and will result in a $75.00 charge per call.
As with any text-to-speech service, there may be parts of the address that are not appropriately recognized and therefore, skipped in the playback. The purpose of using the 933 service is to verify that:
Calls are reaching the correct carrier and location
Some resemblance of the address provided in the dashboard is being represented
o For example, if the 9-1-1 address entered is "123 N Main St, Ste 400, Denver Colorado 80205", the 933 service would likely read back "123 Main, Denver Colorado 80205". This would be considered a successful call. If it read back something entirely different, such as "2963 Stormy Ave, El Paso TX", this would indicate a problem either with the 933 service or with the address in the portal. Please contact Intelepeer Support ([email protected]) immediately with this information so we can ensure that the address is configured properly.
The 933 service may be used any time (please limit calls to one call per minute); however, it is a courtesy service and is not meant to be used as a fully functional address verification service. To verify a full address, it is best to reach out to Intelepeer at [email protected] for address confirmation.