Security Sensors - TAKEX · 2013. 5. 23. · Stand-alone use or compatible with all CCTV, Access...

4
Security Sensors UK PRODUCT LIST

Transcript of Security Sensors - TAKEX · 2013. 5. 23. · Stand-alone use or compatible with all CCTV, Access...

Page 1: Security Sensors - TAKEX · 2013. 5. 23. · Stand-alone use or compatible with all CCTV, Access Control, Intruder Systems. Horn Speaker Activated by Built-In 12m x 12m PIR, External,

Security Sensors

UK PRODUCT LIST

Page 2: Security Sensors - TAKEX · 2013. 5. 23. · Stand-alone use or compatible with all CCTV, Access Control, Intruder Systems. Horn Speaker Activated by Built-In 12m x 12m PIR, External,

TAKEX ARE PLEASED TO OFFER ASSISTANCE WITH PRODUCT SELECTION AND SYSTEM DESIGN

ACTIVE INFRARED BEAMS For Use Stand-Alone OR In Beam Towers (But For Use In Beam Towers See Note* Below)

Note* TA Series Beam Towers will accept all TAKEX Twin and Quad beam sets (listed following), but for preference use KH Series Beams (listed below TA Towers), designedspecifically for use in TA Towers and supplied with PTKH ‘Quick-fix’ Mounting Bracket.

\\\ TWIN BEAMS 12/24VDCPB-30TKPB-60TKPB-100TKfor ‘stacked’ or multiple in-line beam systems, use 4-Channel units to avoid ‘crosstalk’PB-20TEPB-40TEPB-60TE

Up to 30m External / 60m Internal Twin Beam (Single Channel: Ch-3) use BP-60A Pole Clamp (if required)Up to 60m External / 120m Internal Twin Beam (Single Channel: Ch-3) use BP-60A Pole Clamp (if required)Up to 100m External / 200m Internal Twin Beam (Single Channel: Ch-3) use BP-60A Pole Clamp (if required)

Up to 20m External / 40m Internal Intelligent Twin Beam (4-Channel) use BP-60A Pole Clamp (if required)Up to 40m External / 80m Internal Intelligent Twin Beam (4-Channel) use BP-60A Pole Clamp (if required)Up to 60m External / 120m Internal Intelligent Twin Beam (4-Channel) use BP-60A Pole Clamp (if required)

\\\ QUAD BEAMS 12/24VDCPB-50FPB-100FPB-200Ffor ‘stacked’ or multiple in-line beam systems, use 4-channel units to avoid ‘crosstalk’PB-IN-50HFPB-IN-100HFPB-IN-200HF

Up to 50m External / 100m Internal Quad Beam (Single Channel: Ch-3) includes Pole ClampsUp to 100m External / 200m Internal Quad Beam (Single Channel: Ch-3) includes Pole ClampsUp to 200m External / 400m Internal Quad Beam (Single Channel: Ch-3) includes Pole Clamps

Up to 50m External / 100m Internal Intelligent Quad Beam (4-Channel) includes Pole ClampsUp to 100m External / 200m Internal Intelligent Quad Beam (4-Channel) includes Pole ClampsUp to 200m External / 400m Internal Intelligent Quad Beam (4-Channel) includes Pole Clamps

\\\ ANTI-CRAWL BEAM 12/24VDC (Lower Beam Detects Crawling / Low Level Intrusion For High Security Applications)PB-IN-100AT Up to 100m External / 200m Internal Intelligent Anti-Crawl Beam (4-Channel) includes Pole Clamps

\\\ BATTERY-POWERED/LOW CURRENT BEAM (For Wireless Systems, Batteries and Wireless Tx Not Supplied) PB-IN-75SWA beam suitable for battery powered use for wireless applications, difficult-to-cable-to areas, or where there is no mains power.Use with a local sounder or any-make wireless transmitter or GSM dialler etc. (not supplied) for remote signalling to createtemporary or permanent secure systems. Contact TAKEX for application and system design advice / battery options, duration etc.

Up to 75m External / 150m Internal 6/12/24VDC Battery-Powered Beam (4-Channel) includes Pole Clamps

\\\ ACCESSORIES FOR ACTIVE IR BEAMSBP-60APBHBP-60TEBP-200FSS-COVER-TWINSS-COVER-QUADTWINCAGEQUADCAGE

Pole Clamps for TK/TE Beams - NOTE: Supplied Free-of-Charge If Ordered At The Same Time As The Beam SetHeaters (Thermistor Type, Per Pair) 12-24VDC 350mA (max) for Twin and Quad Beams - For Severe Weather SitesOptional Cover for TK/TE Twin Beams To Hide Rear of Mounting Pole (Per Pair)Optional Cover for all F and HF Quad, 100AT, and 75SW Beams To Hide Rear of Mounting Pole (Per Pair)Replacement Front Cover for all TK and TE Twin BeamsReplacement Front Cover for all F and HF Quad, 100AT, and 75SW BeamsAnti-Vandal Steel Cage for all TK and TE Twin Beams (Black or White - State Preference)Anti-Vandal Steel Cage for all F and HF Quad, 100AT, and 75SW Beams (Black or White - State Preference)

TA SERIES BEAM TOWERS (BEAM SETS NOT INCLUDED - USE KH SERIES BEAMS, LISTED BELOW)

TA series Beam Towers will accept all TAKEX Twin and Quad Beam sets (listed above), but for preference use KH series Quad Beams (listed below), designed specificallyfor use in TA series Towers and supplied with PTKH ‘Quick-fix’ Mounting Bracket.

\\\ TAS SERIES SINGLE-SIDED FLOOR-MOUNT BEAM TOWERS (180° VIEW)TAS100TAS150TAS200TAS300

1m Single-Sided (180°) Floor-Mount Beam Tower1.5m Single-Sided (180°) Floor-Mount Beam Tower2m Single-Sided (180°) Floor-Mount Beam Tower3m Single-Sided (180°) Floor-Mount Beam Tower

\\\ TAW SERIES SINGLE-SIDED WALL-MOUNT BEAM TOWERS (180° VIEW)TAW100TAW150TAW200TAW300

1m Single-Sided (180°) Wall-Mount Beam Tower1.5m Single-Sided (180°) Wall-Mount Beam Tower2m Single-Sided (180°) Wall-Mount Beam Tower3m Single-Sided (180°) Wall-Mount Beam Tower

\\\ TAD SERIES DOUBLE-SIDED FLOOR-MOUNT BEAM TOWERS (360° VIEW)TAD100TAD150TAD200TAD300

1m Double-Sided (360°) Floor-Mount Beam Tower1.5m Double-Sided (360°) Floor-Mount Beam Tower2m Double-Sided (360°) Floor-Mount Beam Tower3m Double-Sided (360°) Floor-Mount Beam Tower

\\\ ACCESSORIES FOR TA SERIES BEAM TOWERSTAPSCRFBTA-PSU2AHeaters with Thermostats are recommended for Beam-Tower sites where frost is anticipated PTH*PTS***One Heater required per Beam Unit Tx or Rx i.e. 2 Heaters per Beam Set **One Thermostat required per Tower

Anti-Climb Switch for All TA Series Towers (Pressure-Sensitive)Mounting Base Root-Bolt-Set for TAS and TAD Towers (Optional: For Setting Into Wet Concrete)Optional: 12VDC 2A ‘In-Tower’ Power Supply - Requires 12V Standby Battery, Up To 7A (Not Supplied)

Heater 12VDC 250mA For All TA Series Beam Towers (Requires PTS Thermostat)Thermostat For All TA Series Beam Towers (For Use With PTH Heaters)

\\\ KH SERIES QUAD BEAMS For Use In TA Series Beam Towers (Includes PTKH ‘Quick-fix’ Mounting Bracket)PB50HF-KHPB100HF-KHPB200HF-KHPB100AT-KH

Up to 50m External / 100m Internal Quad Beam (4-Channel) - For Use In Beam Towers Only Up to 100m External / 200m Internal Quad Beam (4-Channel) - For Use In Beam Towers OnlyUp to 200m External / 400m Internal Quad Beam (4-Channel) - For Use In Beam Towers OnlyUp to 100m External / 200m Internal Anti-Crawl Beam (4-Channel) to detect crawling or low-level intrusion

3m

2m

1.5m

1m

Page 3: Security Sensors - TAKEX · 2013. 5. 23. · Stand-alone use or compatible with all CCTV, Access Control, Intruder Systems. Horn Speaker Activated by Built-In 12m x 12m PIR, External,

SPECIAL PURPOSE BEAMS / POINT-TO-POINT MICROWAVE

\\\ POINT-TO-POINT MICROWAVE For Harsh Environments / Practically Immune to Extreme Weather ConditionsMW-50 50m External Point-to-Point (Tx/Rx) Microwave *H (High) or L (Low) Frequency Options Available. 12/24VDC

\\\ COMBINATION IR AND MICROWAVE SENSORCOM-IN-50HF*To avoid crosstalk on sites with multiple in-line units, H and L channel options are available. Please seek advice from TAKEX.

50m External Point-to-Point (Tx/Rx) Microwave and Intelligent Quad Beam *H/L Options. 12/24VDC

\\\ MINIATURE BEAMS 12/24VDCPB-10NSPB-10TNS

Miniature Single IR Beam (1 x Tx, 1 x Rx), Remote Heads (10m cable), 10m Range (Tx to Rx) Inc. Control UnitMiniature Double IR Beam (2 x Tx, 2 x Rx, AND/OR Mode), (10m cable), 10m range (Tx to Rx) Inc. Control Unit

\\\ TWIN BEAM WITH BUILT-IN SOUNDER AND STROBE 12VDCPBS-15TInstant audible + visual warning for Security, Health & Safety, danger areas, or general warnings.

Up to 15m External / 30m Internal Beam c/w 90dB Sounder + High Intensity LED Strobe (Rx end), Alarm O/P

EXTERNAL / SPECIALIST PIR

\\\ MULTI-PATTERN PIR SENSOR 12/24VDC (For Security, Lighting Control, CCTV Presets...)MS-100E

A multi-purpose, multi-use external PIR: includes various detection pattern lenses, Day/Night Sensor, Timed Output Relay (2 sec - 5min)

Multi-Pattern External PIR (Supplied With Lenses For 10m Wide Angle, 10m Vertical/Horizontal Curtain,20m x 2m Long Range) Day/Night Sensor, Timed Output 2 Seconds to approx. 5 Minutes

\\\ REQUEST-TO-EXIT SENSOR 12/24VAC/DC PS-520EUse as an alternative to ‘Request-to-Exit’ buttons for hands-free convenience when exiting

Request-to-Exit Door Sensor (can be wired Fail-Locked or Fail-Open) 12/24VAC/DC

\\\ EXTERNAL PET-TOLERANT PIRs 12/24VDC (For Security, Lighting Control, CCTV Presets...)MS-12TEMS-12FEOMS-12FE

Single Head, Wide Angle 90° x 12m, Day/Night Sensor, Timed O/P 2-300 secsDual Head, 2 x Wide Angle 90° x 12m, (AND/OR Mode) Day/Night Sensor, Timed O/P 2-300 secsFixed Head, Wide Angle 180° x 12m

\\\ BATTERY OPERATED EXTERNAL PET-TOLERANT PIRs (For Security, Lighting Control, CCTV Presets...)TX-114SRTX-114SR will accommodate most small other-makes wireless transmitters (not supplied)TX-114TRTX-114FRTX-114TR/FR has extended rear case to accommodate most makes wireless transmitters (not supplied)

Battery Operated (PP3 9V) Pet-Tolerant PIR, External, Single Head, Wide Angle 90° x 12m

Battery Operated (PP3 9V) Pet-Tolerant PIR, External, Single Head, Wide Angle 90° x 12mBattery Operated (PP3 9V) Pet-Tolerant PIR, External, Dual Head, 2 x Wide Angle 90° x 12m (AND/OR Mode)

\\\ MEDIUM RANGE PIR SENSORS 12/24VDC (For Security, Lighting Control, CCTV Presets...)PA-15WEPA-30NE

External PIR, Omni-Directional Wall/Ceiling Mount Bracket, Wide Angle 15m x 15mExternal PIR, Omni-Directional Wall/Ceiling Mount Bracket, Long Range 30m x 3m

\\\ LONG RANGE PIR SENSORS 12/24VDC (For Security, CCTV Presets...)PIR-30WEPIR-50NEWO-2DBL-8400BP-03

External PIR, Long Range Wide Angle 30m x 30m at 3.5m Mounting Height, Tilt/Tamper SwitchExternal PIR, Long Range Narrow Angle 50m x 3m at 3.5m Mounting Height, Tilt/Tamper SwitchWall Mount Bracket (CCTV Type) for PIR-30WE/50NE, Requires BL-8400 Rear AdaptorRear Adaptor (Required For Use With WO-2D Wall Mount Bracket)Pole Mount Clamp For PIR-30WE/50NE (To Attach To Lighting Columns, Poles etc.)

SPEECH WARNING DEVICES Built-In Microphone, Record Any Message Up To 8 Seconds Long)

\\\ HORN SPEAKER TYPE 12VDCPV-12AV-100Record any message (up to 8 seconds), Real Voice Output: Maximum impact for Security, Health & Safety, Advisory Warnings...Stand-alone use or compatible with all CCTV, Access Control, Intruder Systems.

Horn Speaker Activated by Built-In 12m x 12m PIR, External, 100dB (Adjustable), Alarm Output ContactsAs PV-12 But Without PIR: Requires External Alarm Trigger Input From Another Device (N/O Contact)

\\\ PIR SENSOR SPEAKER 12/24VDCPVW-12TE

Record any 2 messages (each up to 8 seconds), Real Voice Output for Security, Health & Safety, Advisory Warnings...Arm/Disarm or Message Selection by Built-in Photocell (Day/Night) or External Inputs.

Pet-Tolerant PIR, External, Single Head, Wide Angle 90° x 12m, Day/Night Sensor, 2 x Message Speech Unit(For Day, Night, Or Selectable) 80dB (Adjustable)

REFLECTOR BEAMS

\\\ INTERNAL REFLECTOR BEAMS 12VDC, 12/24VDCPR-1BPR-5BPR-10B

Non-Reflector Beam, Internal Use Only: No Reflector Required, Beam Reflects Off ‘Target’. Range Up To 1m. 12VDCReflector Beam With Reflector, Internal Use Only. Range Up To 5m. 12/24VDCReflector Beam With Reflector, Internal Use Only. Rotating Head, Range Up To 10m. 12VDC

\\\ EXTERNAL REFLECTOR BEAM 12/24VDCPR-11BBL-11Reflector Beams require cable to the Transceiver end only, and are a convenient way to monitor entrances, gateways and drives wherecabling to both ends is a problem. For general monitoring, lighting control etc.

Reflector Beam With Reflector. Rotating Head, Range Up To 15m Internal / 11m External. 12/24VDC‘L’ Bracket for PR-11B Reflector (Optional)

TAKEX ARE PLEASED TO OFFER ASSISTANCE WITH PRODUCT SELECTION AND SYSTEM DESIGN

Page 4: Security Sensors - TAKEX · 2013. 5. 23. · Stand-alone use or compatible with all CCTV, Access Control, Intruder Systems. Horn Speaker Activated by Built-In 12m x 12m PIR, External,

ACTIVE IR BEAMSThe ultimate in trouble-free perimeter detection up to 200m outdoor / 400m indoor.

EXTERNAL PIRHigh performance mirror optics external PIR. 30m Wide angle or 50m x 3m long range narrow angle

MINI BEAMSMiniature beams for discreet detection across doorways, windows, prestige/covert applications.

REFLECTOR BEAMSA convenient way to monitor entrances/driveways etc. where cabling to both ends is impractical.

SPEAKER SENSORSRecord any voice or sound message for warning/security, health and safety, advisory or greeting applications.

PET-TOLERANT PIRUp to 12m external range at 90º or 180º detection area - hardwired or wireless versions available.

Reliable Perimeter Intrusion Detection (PIDs) is an art, and we consider ourselves masters

From Active Infra-Red Beams and Beam Tower systems capable of monitoring the smallest of areas to the largest of commercial and industrial sites, via hardwired or wireless external pet-tolerant PIRs and Speech Warning devices for security, health and safety or advisory

messages, TAKEX equipment is used by professional security installers worldwide.

TAKEX are pleased to offer assistance with product selection and system design.

tel: 01256 475555 | email: [email protected] | web: www.takex.comTAKEX Europe, Ltd. | Aviary Court, Wade Road

Basingstoke, Hampshire, RG24 8PE, UK

TA Series Beam Towers• TAS (single-sided), TAD (double-sided) and TAW (wall mount) versions available

• available in 1m, 1.5m, 2m or 3m heights

• anodised aluminium column for high resistance to oxidation

• tamper protected to prevent unauthorised interference

• vandal resistant polycarbonate covers conceals number and position of beams from would-be intruders

KH Series Quad Beams• PB-50HF-KH (50m), PB-100HF-KH (100m) and PB-200HF-KH (200m) models available

• 4 x synchronised high power double modulated beams

• selectable 4-channel beam frequencies allows stacking without crosstalk

• double coated electronics for demanding environments

• environmental monitoring circuit