Release Notes for Cisco Remote PHY Device, Cisco 1x2 / … · CHAPTER 1 Introduction...

Release Notes for Cisco Remote PHY Device, Cisco 1x2 / Compact ShelfRPD Software 7.xFirst Published: 2019-08-30

Last Modified: 2020-03-11

Americas HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706USAhttp://www.cisco.comTel: 408 526-4000

800 553-NETS (6387)Fax: 408 527-0883

C H A P T E R 1Introduction

Explore the Content Hub, the all new portal that offers an enhanced product documentation experience.

• Use faceted search to locate content that is most relevant to you.

• Create customized PDFs for ready reference.

• Benefit from context-based recommendations.

Get started with the Content Hub at content.cisco.com to craft a personalized documentation experience.

Do provide feedback about your experience with the Content Hub.

Note

This Release Notes contain information about downloading and installing Cisco 1x2 / Compact Shelf RPDSoftware 7.x. It also provides new and changed information, hardware support, limitations and restrictions,and caveats for Cisco 1x2 / Compact Shelf RPD Software 7.x.

We recommend that you view the field notices for this release to see if your software or hardware platformsare affected. If you have an account at Cisco.com, you can find the field notices athttp://www.cisco.com/en/US/customer/support/tsd_products_field_notice_summary.html.

If you do not have an account at Cisco.com, you can find the field notices athttp://www.cisco.com/en/US/support/tsd_products_field_notice_summary.html.

Cisco 1x2 / Compact Shelf RPD Software 7.x is generally available for field deployment. To ensure a smoother,faster, and successful field deployment, we recommend that you validate and qualify the software in a limitedfield trial.

Note

The versions of Cisco cBR-8 router and RPDmust be compatible. If the versions are not compatible, the RPDremains in the init(gcp) state. The following list provides information on the compatible Cisco cBR-8 andRPD versions:

• Cisco IOS XE Everest 16.6.x works with RPD 2.x

• Cisco IOS XE Fuji 16.7.x works with RPD 3.x



Release Notes for Cisco Remote PHY Device, Cisco 1x2 / Compact Shelf RPD Software 7.x1

https://content.cisco.com/

http://www.cisco.com/en/US/support/tsd_products_field_notice_summary.html

http://www.cisco.com/en/US/support/tsd_products_field_notice_summary.html

• Cisco IOS XE Gibraltar 16.10.1c works with RPD 6.1, 6.2 and 6.3

• Cisco IOS XE Gibraltar 16.10.1d works with RPD 6.4, 6.5 and 6.7

• Cisco IOS XE Gibraltar 16.10.1f works with RPD 6.6 and 6.7

• Cisco IOS XE Gibraltar 16.10.1g works with RPD 7.1, 7.2, 7.3, 7.4.x, and 7.5

• Cisco IOS XE Gibraltar 16.12.1 works with RPD 7.1, 7.2, 7.3, 7.4.x, and 7.5

• Cisco IOS XE Gibraltar 16.12.1w works with RPD 7.1, 7.2, 7.3, 7.4.x, and 7.5

• Cisco IOS XE Gibraltar 16.12.1x works with RPD 7.6 and 7.7

• Cisco IOS XE Gibraltar 16.12.1y works with RPD 7.8 and 7.8.1

This chapter includes the following sections:

• System Requirements, on page 2• New and Changed Information, on page 7• MIBs, on page 25• Obtaining Documentation and Submitting a Service Request, on page 26

System RequirementsThese sections describe the system requirements for Cisco 1x2 / Compact Shelf RPD Software 7.x:

Memory Requirements for Cisco 1x2 / Compact Shelf RPD Software 7.x

Memory is not configurable for the Cisco Remote PHY device.Note

Table 1: Memory Recommendation for the CIsco Remote PHY Device, Cisco 1x2 / Compact Shelf RPD Software 7.8.1

Runs FromFixed MemorySoftware ImageCisco RPHYProcessor

Feature Set

Bootflash:1G BytesRPD-V7-8-1.itb.SSANXP LS1043ACISCO RPHY 7.8.1

Table 2: Memory Recommendation for the CIsco Remote PHY Device, Cisco 1x2 / Compact Shelf RPD Software 7.8


Feature Set

Bootflash:1G BytesRPD-V7-8.itb.SSANXP LS1043ACISCO RPHY 7.8


IntroductionSystem Requirements



Feature Set




Feature Set




Feature Set


Table 6: Memory Recommendation for the CIsco Remote PHY Device, Cisco 1x2 / Compact Shelf RPD Software 7.4.1


Feature Set

Bootflash:1G BytesRPD-V7-4-1.itb.SSANXP LS1043ACISCO RPHY 7.4.1



Feature Set


Table 8: Memory Recommendations for the Cisco Remote PHY Device, Cisco 1x2 / Compact Shelf RPD Software 7.3


Feature Set




Feature Set



IntroductionMemory Requirements for Cisco 1x2 / Compact Shelf RPD Software 7.x



Feature Set


Hardware SupportedFor detailed information about the hardware supported in Cisco 1x2 / Compact Shelf RPD Software 7.x, see:

http://www.cisco.com/c/en/us/td/docs/cable/cbr/installation/guide/b_cbr_how_and_what_to_order.html.

Determining the Software Version of Cisco 1x2 / Compact Shelf RPD Software7.x

Cisco 1x2 / Compact Shelf RPD Software 7.8.1To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:R-PHY#show versionCisco RPD Software, version v7.8.1, build by rpd-release, on 2020-03-06 03:24:29Branch information:

RPD branch: (HEAD detached at RPD_V7_8_1_20200306)OpenRPD branch: (HEAD detached at RPD_V7_8_1_20200306)SeresRPD branch: (HEAD detached at RPD_V7_8_1_20200306)

The system image file name of the factory installed image is/bootflash/RPD-V7.8.1_hardware_certificate.itb.rel.sign.SSA. The system image file name of the SecureSoftware Download (SSD) from the Cisco software download page is /bootflash/RPD-V7-8-1.itb.SSA.act.

Note

Cisco 1x2 / Compact Shelf RPD Software 7.8To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:R-PHY#show versionCisco RPD Software, version v7.8, build by rpd-release, on 2020-02-27 11:26:19Branch information:

RPD branch: (HEAD detached at RPD_V7_8_20200227)OpenRPD branch: (HEAD detached at RPD_V7_8_20200227)SeresRPD branch: (HEAD detached at RPD_V7_8_20200227)

The system image file name of the factory installed image is/bootflash/RPD-V7.8_hardware_certificate.itb.rel.sign.SSA. The system image file name of the Secure SoftwareDownload (SSD) from the Cisco software download page is /bootflash/RPD-V7-8.itb.SSA.act.

Note


IntroductionHardware Supported

http://www.cisco.com/c/en/us/td/docs/cable/cbr/installation/guide/b_cbr_how_and_what_to_order.html

Cisco 1x2 / Compact Shelf RPD Software 7.7To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:R-PHY#show versionCisco RPD Software, version v7.7_20200122234118, build by rpd-release, on 2020-01-22 23:41:18Branch information:



Note

Cisco 1x2 / Compact Shelf RPD Software 7.6To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:R-PHY# show versionCisco RPD Software, version v7.6, build by rpd-release, on 2020-01-06 08:28:02Branch information:



Note

Cisco 1x2 / Compact Shelf RPD Software 7.5To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:R-PHY# show versionCisco RPD Software, version v7.5, build by docker, on 2019-12-10 01:34:25 Branch information:RPD branch: (HEAD detached at RPD_V7_5_20191210)

OpenRPD branch: (HEAD detached at RPD_V7_5_20191210)SeresRPD branch: (HEAD detached at RPD_V7_5_20191210)SeresRPD branch: (detached from RPD_V7_1_20190627)


Note


IntroductionCisco 1x2 / Compact Shelf RPD Software 7.7

Cisco 1x2 / Compact Shelf RPD Software 7.4.1To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:

R-PHY# show versionCisco RPD Software, version v7.4.1, build by rpd-release, on 2019-11-08 07:10:20Branch information:

RPD branch: (detached from RPD_V7_4_1_20191108)OpenRPD branch: (detached from RPD_V7_4_1_20191108)

The system image file name of the factory installed image is/bootflash/RPD-V7.4.1_hardware_certificate.itb.rel.sign.SSA. The system image file name of the SecureSoftware Download (SSD) from the Cisco software download page is /bootflash/RPD-V7-4-1.itb.SSA.act.

Note

Cisco 1x2 / Compact Shelf RPD Software 7.4To determine the version of the Cisco 1x2 RPD software running on your Cisco Remote PHY Device, log inand enter the show version EXEC command:

R-PHY# show versionCisco RPD Software, version v7.4, build by rpd-release, on 2019-10-30 09:35:30Branch information:

RPD branch: (detached from RPD_V7_4_20191030)OpenRPD branch: (detached from RPD_V7_4_20191030)SeresRPD branch: (detached from RPD_V7_4_20191030)


Note




Note


IntroductionCisco 1x2 / Compact Shelf RPD Software 7.4.1




Note




Note

New and Changed InformationThe following sections list the hardware and software features supported on the Cisco Remote PHY Devicefor Cisco 1x2 / Compact Shelf RPD Software 7.x.

New Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8.1There are no new software features for Cisco 1x2 / Compact Shelf RPD Software 7.8.1 release.

New Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8The new software features for Cisco 1x2 / Compact Shelf RPD Software 7.8 release are the following:


IntroductionCisco 1x2 / Compact Shelf RPD Software 7.2

Support for TLV 100.14 InOctets, InDelivers, InMcastOctets, OutMcastPkts, and OutMcastOctets

Supports InOctets TLV100.14.4, InDelivers TLV100.14.16, InMcastOctets TLV100.14.26, OutMcastPktsTLV100.14.27, and OutMcastOctets TLV100.14.28.

• InOctets—Reports the total number of octets received in the input IP datagrams, including those receivedin the error.

• InDelivers—Reports the total number of datagrams successfully delivered to the IPuser-protocols(including ICMP).

• InMcastOctets—Reports the total number of octets received in the IP multicast datagrams.

• OutMcastPkts—Reports the number of IP multicast datagrams transmitted.

• OutMcastOctets—Reports the total number of octets transmitted in IP multicast datagrams.

Support for Event 66070514-Enclosure Door Opened Condition Cleared

Cisco RPD 7.8 supports the 66070514-Enclosure door opened condition cleared event.

Event IDError CodeSet

MessageNotes andDetail

EventMessage

RPD PrioritySub-ProcessProcess

66070514B705.14P1 = value ofHostResourcesSystemDate attributeat time ofsensor reading

Enclosuredoor openedconditioncleared; Time:<P1>;<TAGS>;

NoticeSecurityEnvironmental


Supports TLV 41.5 UscCalibration

RPD uses this complex TLV to report the current calibration constant for the RF ports associated with theselected SAC. It includes an entry for each RF port with the UscRfPort as a unique key.

The calibration constant for each port must be read with specific port index specified in the GCP read requestmessage.

The returned value is a signed 16-bit number and is in 1/100th of a dB.

The returned calibration constant should be subtracted from the raw received stream spectral power for anyFFT bin.

Supports TLV 100.14.16 OutRequests and TLV 100.14.23 OutTransmits

OutRequests—This attribute reports the total number of IP datagrams that local IP user-protocols (includingICMP) supplied to the IP in requests for transmission.


IntroductionNew Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.7

OutTransmits—This attribute reports the total number of IP datagrams that this entity supplied to the lowerlayers for transmission.

Enables Strict Enforcement of Password Policy

Service Impacting—Update the default RPD SSH password.Important

Update the default RPD access credentials immediately after you log in to the RPD. From RPD 7.7, it ismandatory to update the SSH login password.

If you continue to use the default password, all downstream channels become inactive. A warning messageappears of the Cisco cBR core and an event is generated for default password usage. The event is generatedfor RPD 6.7 and later. The RPD sends this event to the primary core to which it is connected.

The following message appears when you log in to the RPD y using the default credentials:2020-01-13 04:48:26,584-rpd_logging.py-119-ERROR-0x80090807:Service Disabled - PLEASE CHANGERPD SSH PASSWORD IMMEDIATELY - default login credentials detected in use2020-01-13 04:48:26,586-cli_main.py-216-WARNING-Default password detected in use

************************************************************************* SERVICE IMPACTING *************************************** PLEASE READ ****************************************************************************Default login credentials detected in use.In order to enhance the security of your network,default login credentials must be changed on this RPD.

@@@@ RPD SERVICE HAS BEEN DISABLED !!! @@@@

************************************************************************ CHANGE SSH PASSWORD ************************************* IMMEDIATELY *****************************************************************************

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!SECURITY WARNING: ssh password login is accessible!Please use pubkey login and set password login off!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Welcome to Cisco R-PHY

R-PHY>

Check the current SSH account details using the following command. If you use the default credentials, youcan see a similar output:

R-PHY#show ssh accountAccount Num: 3Current SSH Accounts:admin *** Warning ! Default Password in Use ***



testnew

When the downstream port is inactive due to the use of default credentials, the OFDM channel and the QAMchannel also become inactive. To check whether the downstream port is inactive, use the following command:R-PHY#show downstream port configurationAdmin: UPMuted: MUTEDBasePower: 21 dBmV

R-PHY#show downstream channel configurationChan State Frequency Type Annex Modulation Srate Interleave Power Muted

Chan State Type StartFreq Width PlcFreq CPrefix RollOff Interleave SpacingPower Muted

158 UP OFDM 645000000 192000000 651000000 1024 128 16 50kHz21.0 MUTED

*NOTE: Start frequency and channel width do not cover guardband override scenario.

You can activate the downstream port using one of the following methods:

• Disable the SSH password and set up the RPD to use server-generated SSH keys.

• Change the password for the admin user.

• Create a new user and delete the admin user.

R-PHY#config terminalR-PHY(config)#ssh chpasswd adminPlease enter password for 'admin':Please re-enter your password:chpasswd: password for 'admin' changed

Successfully Changed from Default Password, SoftReset in 10 secondsR-PHY(config)#ssh password off

Successfully Disabled Password, SoftReset in 10 secondsR-PHY(config)#ssh add rpdadminChanging password for rpdadminNew password:Retype password:passwd: password for rpdadmin changed by rootR-PHY(config)#ssh delete adminWarning: Are you sure to delete this account? [No/Yes]yesdelete account 'admin' successfullyR-PHY(config)#

Successfully Deleted user admin, SoftReset in 10 seconds

Supports TLV 100.31 ResetHistory

The TLV 100.31 ResetHistory provides a record of the occurrences of a reset of an RPD. The RPD can resetfor many reasons, including a loss of Principal Core, loss of IP connection, power failure, hardware or softwarefailure, or reset command from CCAP Core or CLI. This object provides the details of the conditions thatcause the RPD to reset and to assist operators with understanding why a service interruption occurs. Thisobject also provides details of how much time it took for the RPD to boot its software stack and to becomeoperational with the principal core.



• If rebootdisable parameter is set, the RPD does not save any record.

• If the power cycle is triggered during a reboot, the application is not notified about it. Hence, afterrecovery, the recovery time and the related information are saved in the latest record. No new recordsare generated for the power cycle reboot.

• About 100.31.7 RecoveryTime:

• softReset—The recoveryTime of the softReset is the RCP process up-time when the system becomesoperational.

• hardReset/nvReset/factoryReset—The recoveryTime is the system up-timewhen the system becomesoperational.

• It stores up to 100 records.

Note

Use the following command to show or the clear RPD reset-history: show|clear reset-history.R-PHY#show reset-historyIndex Type ResetTimeStamp RecoveryTimeStamp RecoveryTime EventRef1 hardReset 2020-01-13 01:42:42 2020-01-13 01:51:22 481 660702122 softReset 2020-01-13 01:30:18 1970-01-01 00:00:00 0 660702123 hardReset 2020-01-13 01:19:19 2020-01-13 01:29:26 568 660702124 hardReset 2020-01-13 00:57:43 2020-01-13 01:16:23 1099 660704115 softReset 2020-01-10 20:02:52 2020-01-11 01:11:40 18527 660702126 softReset 2020-01-10 20:00:30 2020-01-10 20:02:29 118 660702127 softReset 2020-01-10 19:57:51 2020-01-10 19:59:56 124 660702128 softReset 2020-01-10 19:51:30 2020-01-10 19:52:53 82 660702129 hardReset 2020-01-10 19:25:23 2020-01-10 19:40:51 898 6607021210 hardReset 2020-01-10 19:19:39 1970-01-01 00:00:00 0 6607021211 hardReset 2020-01-10 19:13:51 1970-01-01 00:00:00 0 66070212…R-PHY#clear reset-history


Support for New Events

This release supports the following events.



EventMessage


66070331B703.31P1 = CCAPCore ID

BackupPrincipal Corefound; CoreID: <P1>;<TAGS>;

NoticeConfigInit





EventMessage


66070332B703.32P1 = CCAPCore ID

BackupAuxiliaryCore found;Core ID:<P1>;<TAGS>;

NoticeConfigInit

66070333B703.33P1 = CCAPCore ID

Core notacting in anyrole for RPD- Neitheractive norbackupCCAPCore; CoreID: <P1>;<TAGS>;

WarningConfigInit

66070336B703.36P1 = CCAPCore ID

Upgrade IRA;Core ID:<P1>;<TAGS>;

NoticeConfigInit

66070337B703.37P1 = CCAPCore ID

Redirect IRA;Core IP:<P1>; CoreID: <P2>;<TAGS>;

NoticeConfigInit

66070338B703.38P1 = CCAPCore IPaddress

P2 = CCAPCore ID

PendingIRAs; CoreID: <P1>;<TAGS>;

NoticeConfigInit

Support for TLV 100.9.21 IfEnetStats OutDiscards

RPD 7.6 supports TLV 100.9.21 IfEnetStats OutDiscards. This attribute provides the number of outboundpackets which are chosen to be discarded even though errors were not detected with these packets. The packetsare discarded to prevent the system from delivering them to a higher-layer protocol.

Align Current Events to CableLabs RPHY I13 Specification

The following events messages are updated so that they conform to the CM-SP-R-OSSI-I13-190828Specification: 66070203, 66070220, 66070223, 66070224, 66070320, 66070321, 66070327, 66070335,66070403, 66070404, 66070215, 66070500, 66070501.



Enhanced Reporting Event 66070504—Enclosure Door Opened

In the earlier RPD releases, the polling interval for the event, 66070504-Enclosure door opened, was twominutes. Opening and closing the enclosure door in two minutes may not generate the event. In this release,this event is detected and reported in 10 seconds. If the enclosure door remains open for more than 10 sec,the event is reported every two minutes.


Support for TLV 100.14.1, 100.14.31, 100.14.32

RPD 7.5 supports TLV 100.14.1 Ip version, TLV 100.14.31 DiscontinuityTime, and TLV 100.14.32RefreshRate.

New Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.4.1There are no new software features for Cisco 1x2 / Compact Shelf RPD Software 7.4.1 release.

New Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.4The new software features for Cisco 1x2 / Compact Shelf RPD Software 7.4 release are:

• Leakage/Pilot tone generation CW frequency granularity within +/- 0.5 Hz

RPD V7.4 support leakage/pilot tone generation CW frequency granularity within +/- 0.5 Hz. In orderto support this granularity, pilot tone configuration need to follow below rules:

1. Supported tone numbers: 2/3/4.

2. Supported tone index: 0/1/2/3.

3. Tone frequency should be large than 50Mhz.

4. Valid tones need to be configured “no mute”.

5. Frequency spacing should be less than 25MHz in a pair of tone.

6. Go through the following possible scenarios:

• If config 4 tones as two pairs of tones, tone 0 and tone 1 must be a pair, tone 2 and tone 3 mustbe a pair. For example:

R-PHY#show downstream calibration info[ 0, on] 137998869.0 Hz -33.0 dB {OFDM scaler=57159, Sine scaler=174}[ 1, on] 138001131.0 Hz -33.0 dB {OFDM scaler=57159, Sine scaler=174}[ 2, on] 611998717.0 Hz -33.0 dB {OFDM scaler=57159, Sine scaler=162}[ 3, on] 612001283.0 Hz -33.0 dB {OFDM scaler=57159, Sine scaler=162}

• If config 2 tones as a pair of tone, support 2 tones at any tone index in (0, 1, 2, 3). For example:

R-PHY#show downstream calibration info[ 0, on] 611998717.0 Hz -33.0 dB {OFDM scaler=56624, Sine scaler=229}[ 1, on] 612001283.0 Hz -33.0 dB {OFDM scaler=56624, Sine scaler=162}



• If config 3 tones in CT3 mode, support 3 tones at any tone index in (0, 1, 2, 3). For example:

R-PHY#show downstream calibration info[ 1, on] 611998717.0 Hz -30.0 dB {OFDM scaler=56897, Sine scaler=229}[ 2, on] 612001283.0 Hz -33.0 dB {OFDM scaler=56897, Sine scaler=162}[ 3, on] 612000000.0 Hz -31.0 dB {OFDM scaler=56897, Sine scaler=204}


• TLV Error Handling Support

Cisco 1x2 / Compact Shelf RPD Software 7.3 release supports handling GCP/RCP errors. A number oferror scenarios can arise in RCP protocol exchanges. There are two RCP TLVs defined to communicatethe information helpful to identify the type of the error and the details of the underlying error condition.These TLVs are ResponseCode (TLV 19) and ErrorMessage (TLV 20). The Response Code provides anumerical identification of the error, while the ErrorMessage provides a human readable description ofthe error.

Table 11: Defined ResponseCode Values

ExampleDescriptionMnemonicCode Value

Operation completedsuccessfully.

The RPD reports that noerrors occurred duringoperation.

NoError0

No example is provided.An error has occurred.This is a catch-all codefor all errors that do notfit the description ofother specific errorconditions. Whenreturning this Error Codethe RPD providesErrorMessage TLV withadditional informationabout the error.

GeneralError1

The read request by theCCAP Core hasspecified a subtree of theRCP schema that resultsin a response that is over64 KB, i.e., too big to fitin a single RCPmessage.

The RPD could not placethe results of therequested operation in asingle RCP message.

ResponseTooBig2




The CCAP Coreattempts to read a TLVthat the RPD does notrecognize. For examplethe CCAP Core issued aread request for TLV213, which is notdefined.

The CCAP Corerequested a readoperation on an attributeor a set of attributesunrecognized by theRPD.

AttributeNotFound3

The RPD’s capabilitiesindicate support for twoDS RF ports. The CCAPCore issues a writerequest to set theBasePower for a DS RFport with index value of2, which is outside of thevalid range: 0..1.

The CCAP Coreattempted to write to anattribute but it specifiedeither no index or anindex value outside ofthe range supported bythe RPD. This error codecan be also returnedwhen the CCAP Coreissued a Read requestwith at least one of theindex values outside ofthe range supported bythe RPD. This error codeis also applicable whenthe CCAP Core uses abad value of a channel,RF port or Ethernet portselector.

BadIndex4

A CCAP Core attemptsto write to an upstreamchannelCenterFrequencyattribute (TLV 65.4),which is defined asRead-only.

The CCAP Coreattempted to write to aread-only attribute.

WriteToReadOnly5

No example is provided.The value is inconsistentwith values of othermanaged objects.

InconsistentValue6

A CCAP Core attemptsto write to an AttributeBasePower (TLV 61.3)with TLV indicating alength of 1. Thespecification defines thisattribute with TLVlength of 2.

The CCAP Coreattempts to write a valuewith a TLV length thatis inconsistent with thelength required for theattribute.

WrongLength7




A CCAP Core attemptsto write to an attributeRfMute (TLV 61.4) avalue of 2, which isinvalid.

The value cannot beassigned to the attribute.

WrongValue8

A CCAP Core attemptsto create oradministratively enableOFDM channels thatrequire resources sharedwith already-created oralready-enabledSC-QAM channels.

Assigning the value tothe variable requiresallocation of resourcesthat are currentlyunavailable.

ResourceUnavailable9

An Auxiliary CCAPCore attempted to writeto an attribute onlywriteable by the activePrincipal Core, e.g.,BasePower (TLV 61.3)attribute of the DS RFPort.

A CC attempts to writeto an attribute it does notown.

AuthorizationFailure10

The CCAP Core hasattempted anAllocateWrite operationbut has not included anattribute which is used tomark the table entry asallocated.

The RPD expected anattribute which was notprovided.

AttributeMissing11

The CCAP Coreattempted to allocate anentry in a table withAllocateWrite access butthere are no more entriesavailable.

This error code isreturned when theAllocateWrite operationfails because the tablesubject to the operationhas no more entriesavailable. No changesare made to any objectsincluded in the sequence.

AllocationFailure12

The CCAP Coreattempted to allocate anentry in a table withAllocateWrite but didnot include the CoreId.

This error code isreturned when theAllocateWrite operationfails because theattribute set does notinclude a valid owner.

AllocationNoOwner13




A UCD message sent tothe RPD is incorrectlyformatted.

TheRPD encountered anerror when processing aUCDMessage sent fromthe CCAP Core.

ErrorProcessingUCD14

An OCD message sentto the RPD is incorrectlyformatted.

TheRPD encountered anerror when processing anOCDMessage sent fromthe CCAP Core.

ErrorProcessingOCD15

A DPD message sent tothe RPD is missingmandatory DOCSISTLVs.

TheRPD encountered anerror when processing aDPDMessage sent fromthe CCAP Core.

ErrorProcessingDPD16

A CCAP Core attemptsto provision a staticpseudowire with aSession ID that isalready in use by theRPD for the selectedEthernet port.

A Session ID for a staticpseudowire is already inuse.

SessionIdInUse17

Example: The CCAPCore attempted to read adynamically instantiatedconfiguration object thathad not been writtenfirst.

The RPD rejected anattempt to read a singleInterface or Array ROTwith an index set for aninstance that does notexist, or the RPDrejected an attempt towrite to a staticallyconfigured Interface orArray ROT instance thatdoes not exist.

DoesNotExist18

• RPD Event Support

Cisco 1x2 / Compact Shelf RPD Software 7.3 release provides event support for 66070339, 66070226,66070236, 66070225. Information of these events is listed in the following table:



EventMessage


66070339B703.38P1 = CCAPCore ID

PendingIRAs; CoreID: <P1>;<TAGS>;

NoticeConfigInit





EventMessage


66070226B702.26P1 = CCAPCore ID

P2 = CCAPCore IPaddress

Principalreconnectabandoned;CCAP CoreID: <P1>;CCAP CoreIP: <P2>;<TAGS>;

ReconnectConnectivity

66070236B702.36P1 = IPaddress ofFailed Core

P2 = IPaddress ofBackup Core

P3 = IPaddress ofCore sendinghandoverrequest

Core initiatedhandover;Failed CoreIP: <P1>;Backup CoreIP: <P2>;RequestingCore IP:<P3>;<TAGS>;

HandoverConnectivity



P3 = IPaddress ofCore sendinghandoverrequest

Auxiliaryreconnectabandoned;Failed CoreIP: <P1>;Backup CoreIP: <P2>;RequestingCore IP:<P3>;<TAGS>;

ReconnectConnectivity

• SCP Support to Copy RPD Logfiles

Remotely retrieving log files from the RPD via scp is supported in Cisco 1x2 / Compact Shelf RPDSoftware 7.3 release. Leading to a simpler workflow for the customer and Cisco support teams. Forsecurity reasons, the scp support would be limited to specific directories that contain the log files andonly certain types of files under these directories. Only files from /tmp/, /rpd/, /rpd/archive/, /rpd/log/,and /rpd/log/<logname>.log/ are allowed. Filename MUST include one of: 'log', '.gz', or '.pcap'. Thisfeature will only allow copy-out of files and will not allow copying-in of files to the RPD.

• Support for Optical Monitoring TLV-100.18

This feature supports a new TLV on RPHY to read the SFP-Plus object on RPD. This object providesdetailed information about the SFP+ pluggable transceivers on the RPD Ethernet Interfaces. All thevalues in TLV 100.18 are supported with the exception of 100.18.34 - DigitalDiagA2Info.



This object is intended to convey information available from Digital Diagnostic Memory Map of thetransceiver as defined in [SFP 8472].

-The CCAP Core MUST create an instance of the SfpPlusStatus object for every Ethernet interface onthe RPD.

-The CCAP Core reads the SfpPlusStatus object with GCP TLV Type 100.18.

• Support for local archive: Added "local" option to existing CLI

Using the command logging [1588| corefile| provision]-archive local can save a log archive to/rpd/archive on the RPD. This archive can then be transferred out or viewed locally.

Example:R-PHY#logging provision-archive localCollect tech-support info...Please wait, archiving...Created archive: /rpd/archive/RPD_PROV_badbad13ac3e_LOG_2019-08-28_11_59_01_898484.tar.gzCreated archive: /rpd/archive/RPD_running_log.tar.gzCreated archive: /rpd/archive/RPD_config_log.tar.gz[Done]

• Security MIB Support

Cisco 1x2 / Compact Shelf RPD Software 7.3 release supports RpdCert (TLV 100.26), TrustAnchorCert(100.27) and Ieee8021xPaeSupplicantStatus (100.30) for security MIB.

• RpdCert -TLV100.26: This object describes the set of known Certificate Authority certificatesacquired by the RPD, including Signing certificate and Device certificate.

• TrustAnchorCert -TLV100.27: This object describes the set of knownCertificate Authority certificatesuse to validate certificates.

• Ieee8021xPaeSupplicantStatus -TLV100.30: This object reports status information for the IEEE802.1x PAE RPD supplicant.


• RPD P2 Events implementation – Phase 2

RPD V7.2 release provides event support for 66070335, 66070224, 66070234, 66070229, 66070230.Information of these events is listed in the following table:



EventMessage


66070335B703.35P1 = CCAPCore ID

Move tooperationaltimeout; CoreID: <P1>;<TAGS>;

ErrorConfigInit





EventMessage


66070224B702.24P1 = CCAPCore IPaddress

TCP failure;CCAP CoreIP: <P1>;CCAP CoreID: <P2>;<TAGS>;

GCPConnectivity

P2 = CCAPCore ID (ifknown)


Backuprequestrejected;Failed CoreIP: <P1>;Backup CoreIP: <P2>;<TAGS>;




Auxiliaryhandoverstarted;Failed CoreIP: <P1>;Backup CoreIP: <P2>;<TAGS>;




Principalhandoverstarted;Failed CoreIP: <P1>;Backup CoreIP: <P2>;<TAGS>;



• TLV 78.3 support

RPD V7.2 release provides support of TLV 78.3 HcsErrors, which allows the CCAP Core to read thenumber of bursts with detected HCS error in the DOCSIS header for the selected channel. You can checkthe HcsError in RPD CLI show upstream iuc counter, see the example below.R-PHY#show upstream iuc counter 0 0Channel Counters for physical channel 0/0, status valid(1)+-------+----------+-------+----------+-------+-------+----------+----------+----------+-----+|IUC | Grants |Collide| No |Phy |No | Good | Corrected|Uncorrectd|SNR || | | | Energy |Errors |Preambl| FEC | FEC |FEC| |+-------+----------+-------+----------+-------+-------+----------+----------+----------+-----+|1-Req |1274227 |0 |1274211 |0 |0 |0 |0 |0|00.00|



|2-ReqD |0 |0 |0 |0 |0 |0 |0 |0|00.00||3-Init |394 |0 |394 |0 |0 |0 |0 |0|00.00||4-Maint|5 |0 |0 |0 |0 |5 |0 |0|42.00||5-Short|0 |0 |0 |0 |0 |0 |0 |0|00.00||6-Long |0 |0 |0 |0 |0 |0 |0 |0|00.00||9-AShrt|7 |0 |0 |0 |0 |7 |0 |0|42.00||10-ALng|63 |0 |0 |0 |0 |83 |0 |0|43.00||11-AUGS|0 |0 |0 |0 |0 |0 |0 |0|00.00|+-------+----------+-------+----------+-------+-------+----------+----------+----------+-----+

Physical Channel 0/0 Counters:

DOCSIS 2.0 REQ Count: 0 DOCSIS 3.0 REQ Count: 2539REQ Overflow Count : 0 Delete Packet Count : 0 HCS ERR Count: 115High Byte Count : 0 Low Byte Count : 1348846Last Update Time 51.750970 s ago

• RPD TACACS - disable local access if the server is available

When the TACACS server can be reached from RPD, user can only access RPD by TACACS account.Local access will be disabled, which means the user cannot access RPD by local account. But if theTACACS server cannot be reached, for example, a wrong server address, network issue, etc. the usercan access RPD by local account.


• RPD P2 Events implementation – Phase 1

The RPD V7.1 release provides event support for 66070223 and 66070231. Information on these eventsis listed in the following table:

Event IDError Code SetMessage Notesand Detail

Event MessageSub-ProcessProcess

66070223B702.23P1 = CCAPCore IP address

P2 = CCAPCore ID

GCP keepalivefailure; CCAPCore IP: <P1>;CCAPCore ID:<P2>;<TAGS>;

GCPConnectivity

66070231B702.31P1 = Ethernetport number

CIN linktimeout; Port:<P1>;<TAGS>;

EthernetInterface

Connectivity

• TLV 60.13 and 60.14 support



The RPD V7.1 release provides support of new TLV 60.13 GcpBackupConnectionConfig and 60.14CandidateBackupCoreTable as described below:

• 60.13 GcpBackupConnectionConfig: Currently, RPD only support the default value “connection”.The default value always allow a backup mode core to maintain GCP control connection. This TLVcan be used to support the MIB items docsRphyRpdDevCoresConnectedTable anddocsRphyRpdDevCoresConnectedGcpBackupConnectionConfig

.• 60.14 CandidateBackupCoreTable: It provides a list of potential backup cores. Index (60.14.1)and BackupCoreIpAddress(60.14.2) of the core based on the Cisco internal TLV 200RedundantCoreIpAddress. It can be used to support the MIB tabledocsRphyRpdDevCandidateBackupCoresTable.

Modified Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8.1There are no modified software features for Cisco 1x2 / Compact Shelf RPD Software 7.8.1 release.

Modified Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8There are no modified software features for Cisco 1x2 / Compact Shelf RPD Software 7.8 release.




Modified Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.4.1There are no modified software features for Cisco 1x2 / Compact Shelf RPD Software 7.4.1 release.




IntroductionModified Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8.1



Integrated Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8.1There are no integrated software features for Cisco 1x2 / Compact Shelf RPD Software 7.8.1 release.

Integrated Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.8There are no integrated software features for Cisco 1x2 / Compact Shelf RPD Software 7.8 release.




Integrated Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.4.1There are no integrated software features for Cisco 1x2 / Compact Shelf RPD Software 7.4.1 release.





IntroductionModified Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.2

Integrated Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.1There are no new integrated software features for Cisco 1x2 / Compact Shelf RPD Software 7.1 release.

New Hardware Features in Cisco 1x2 / Compact Shelf RPD Software 7.8.1There are no new hardware features for Cisco 1x2 / Compact Shelf RPD Software 7.8.1 release.

New Hardware Features in Cisco 1x2 / Compact Shelf RPD Software 7.8There are no new hardware features for Cisco 1x2 / Compact Shelf RPD Software 7.8 release.




New Hardware Features in Cisco 1x2 / Compact Shelf RPD Software 7.4.1There are no new hardware features for Cisco 1x2 / Compact Shelf RPD Software 7.4.1 release.






IntroductionIntegrated Software Features in Cisco 1x2 / Compact Shelf RPD Software 7.1

MIBsTo locate and download MIBs for selected platforms, Cisco IOS XE releases, and feature sets, use Cisco MIBLocator found at the following URL:

https://mibs.cloudapps.cisco.com/ITDIT/MIBS/servlet/index

MIBs in Cisco 1x2 / Compact Shelf RPD Software 7.8.1There are no new MIBs in Cisco 1x2 / Compact Shelf RPD Software 7.8.1.

MIBs in Cisco 1x2 / Compact Shelf RPD Software 7.8There are no new MIBs in Cisco 1x2 / Compact Shelf RPD Software 7.8.




MIBs in Cisco 1x2 / Compact Shelf RPD Software 7.4.1There are no new MIBs in Cisco 1x2 / Compact Shelf RPD Software 7.4.1.





IntroductionMIBs

https://mibs.cloudapps.cisco.com/ITDIT/MIBS/servlet/index


Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, using the Cisco Bug Search Tool (BST), submitting a servicerequest, and gathering additional information, see What’s New in Cisco Product Documentation.

To receive new and revised Cisco technical content directly to your desktop, you can subscribe to the What’sNew in Cisco Product Documentation RSS feed. The RSS feeds are a free service.


IntroductionMIBs in Cisco 1x2 / Compact Shelf RPD Software 7.1

http://www.cisco.com/c/en/us/td/docs/general/whatsnew/whatsnew.html

http://www.cisco.com/assets/cdc_content_elements/rss/whats_new/whatsnew_rss_feed.xml

http://www.cisco.com/assets/cdc_content_elements/rss/whats_new/whatsnew_rss_feed.xml

C H A P T E R 2Caveat List

This chapter describes open severity 1 and 2 caveats and select severity 3 caveats:

• The Open Caveats sections list open caveats that apply to the current release and may apply to previousreleases. A caveat that is open for a prior release and is still unresolved applies to all future releases untilit is resolved.

The bug IDs are sorted alphanumerically.

The Caveats section includes the bug ID and a short description of the bug. For details on the symptoms,conditions, and workaround for a specific caveat you must use the Bug Search Tool.

Note

• Cisco Bug Search, on page 28• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8.1, on page 28• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8, on page 28• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.7, on page 28• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.6, on page 28• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.5, on page 29• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.4.1, on page 29• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.4, on page 29• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.3, on page 30• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.2, on page 30• Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.1, on page 30• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8.1, on page 31• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8, on page 31• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.7, on page 31• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.6, on page 32• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.5, on page 32• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.4.1, on page 32• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.4, on page 32• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.3, on page 33• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.2, on page 33• Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.1, on page 34


Cisco Bug SearchCisco Bug Search Tool (BST), the online successor to Bug Toolkit, is designed to improve effectiveness innetwork risk management and device troubleshooting. You can search for bugs based on product, release,and keyword, and aggregates key data such as bug details, product, and version. For more details on the tool,see the help page located at http://www.cisco.com/web/applicat/cbsshelp/help.html.

Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8.1DescriptionCaveat ID Number

RPD: WB FFT repeatPeriod control TLV does appear to work correctlyCSCvt10120

66070101 Mutual Authentication error not triggered when ipsec auth failedCSCvt14140

Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8DescriptionCaveat ID Number

Cisco RPD: WB FFT repeatPeriod control TLV does appear to work correctly.CSCvt10120

66070101 Mutual Authentication error not triggered when ipsec auth failed.CSCvt14140


Some MIBs of docsRphyRpdIpIfStats are not highly accurate as expectedCSCvs59600

RPD Warm Reset will not set password back to on, if there is no ssh nms-pubkeyconfigured

CSCvs64442

reset-history display wrong reset type when cold reboot during soft rebootCSCvs69902

ERR and exception about sensor and mac-address keep printing in openrpd.logCSCvr85971


Spectrum corruption is seen whenever the NDF channel width ischanged.

CSCvs54503


Caveat ListCisco Bug Search

http://www.cisco.com/web/applicat/cbsshelp/help.html

https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvt10120




https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvs59600



https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvr85971


DescriptionCaveat ID Number

Door open event did not report when TOD server time is aheadthan last evet report time.

CSCvs56062

No error response when read tvl 100.17 with invalid key.CSCvs56432


RPHY: Bit status display wrong fordocsRphyRpdIfEnetSfpPlusStatusStatus.

CSCvs34086

RPHY: power voltage reading from the show environmentcommand does not match the power supply.

CSCvs36996

Config remove and add may lead to NDF Spectrum Corruptionand gets recovered on its own.

CSCvs34577

Power level accuracy issue of Dedicated Tone used as LegacyPilot tone.

CSCvs44785

Open Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.4.1DescriptionCaveat ID Number

RF Tuner not locking in annex C video broadcast intermittently with long run timeCSCvr66631

6x12 shelf group id all 0 in some casesCSCvr84589

Implement Ifstats MIBCSCvr73987


6x12 shelf group id all 0 in some casesCSCvr84589

RPHY: Definition of TLV length for Precision(100.7.4) is not correctCSCvr73987

RF Tuner not locking in annex C video broadcast intermittently with long run timeCSCvr66631


Caveat ListOpen Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.5














Compact shelf RPD does not come online when event reproting flag with 0x2CSCvr33909

RPHY: DHCP/TOD events show wrong "Port" informationCSCvr42390

RPHY: docsRphyRpdIpAddressCreated reports wrong time for link-local addressesCSCvr42419

RPHY: GetUsPortPgaGain ValueError: Value out of range: -59900CSCvr44169

RPD TLV 50.37 response (RPDCapabilities DsSchedulerPhbIdList - 50.37) incorrectCSCvr35658

TLV 100.18 SfpPlusStatus not implemented error handlingCSCvr36351

Some RPD will stuck in init(gcp) after perform SUPHACSCvr48377


RPHY: 552 OOB, STBs will not sign-on due to timing failureCSCvr03413

RPHY IGMP Group specific query not responding with membership report for videoqam's

CSCvr06015


Occasionally all d31 wcm p-online and bcm chip lockup after many config changesCSCvp17960

viavi clc HA showing captured spectrum shifted to right by about 15MhzCSCvq11034

RPD: P2 66070231 CIN Link Timeout using port number as ALLCSCvq67341

TACACS support: Disable/enable local access based on TACACS reachabliliyCSCvq67634


Caveat ListOpen Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.3










https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvp17960

https://bst.cloudapps.cisco.com/bugsearch/bug/CSCvq11034



Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software7.8.1


Device Cert Not Installed Correctly at RPD boot time causing 802.1x failureCSCvt31255

Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software7.8


Config Remove and add may lead to NDF Spectrum Corruption and gets recoveredon its own.

CSCvs34577

RF Tuner not locking in annex C video broadcast intermittently with long run time.CSCvr66631

Spectrum corruption is seen whenever the NDF channel width is changed.CSCvs54503

RPD Warm Reset does not set password back to on, if there is no ssh nms-pubkeyconfigured.

CSCvs64442

Cisco cBR-8: dynamic modulation for R-PHY will bring CM in partial state or createun-recoverable errors.

CSCvs92746

show downstream channel configurationCLI failed for reason: Value out of range:4294767296.

CSCvs57478

DHCPv4 Events 660703xx not following the spec.CSCvs89649

Cisco RPHY-PTP announce interval of 0 not work.CSCvt00938



door open event did not report when TOD server time is ahead than last evet reporttime

CSCvs56062

No error response when read TLV 100.17 with invalid keyCSCvs56432


Caveat ListResolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.8.1














"TLV 58.3.6 AttributeMissing" error response returned by 7.4.1RPD when configuring UTSC capture.

CSCvs15978

RPHY: power voltage reading from show environment commanddoes not match power supply.

CSCvs36996

Power level accuracy issue of Dedicated Tone used as LegacyPilot tone.

CSCvs44785



RPD does not recover from PTP Holdover after temporary IPnetwork degradation.

CSCvr46807

6x12 shelf group ID all 0 in some cases.CSCvr84589

Video not working after receiving partial configuration in TLV62 [DsScQamChannelConfig].

CSCvr99924

Resolved Caveats for Cisco 1x2 / Compact Shelf RPD Software7.4.1


RPD: production RPD failed to boot up when temperature is lower than -20 CelsiusCSCvr99260



Compact shelf RPD does not come online when event reproting flag with 0x2CSCvr33909


Caveat ListResolved Caveats for Cisco 1x2 / Compact Shelf RPD Software 7.6










RPD TLV 50.37 response (RPDCapabilities DsSchedulerPhbIdList - 50.37) incorrectCSCvr35658

TLV 100.18 SfpPlusStatus not implemented error handlingCSCvr36351

RPHY: DHCP/TOD events show wrong "Port" informationCSCvr42390

RPHY: docsRphyRpdIpAddressCreated reports wrong time for link-local addressesCSCvr42419

RPHY: GetUsPortPgaGain ValueError: Value out of range: -59900CSCvr44169

Some RPD will stuck in init(gcp) after perform SUPHACSCvr48377

RPD: P2 66070231 CIN Link Timeout using port number as ALLCSCvq67341

BCM detects CW tone as 55d1 or 55d2 US signalCSCvq27512



55d2 core DS stuck with unknown triggerCSCvp93760

RPHY: 552 OOB, STBs will not sign-on due to timing failureCSCvr03413

static pseudowire multicast is not workingCSCvr03936

RPHY IGMP Group specific query not responding with membership report for videoqam's

CSCvr06015

Wrong scale for current sensorsCSCvr24863

RPHY: Events missing in pending queue after dhcp rebind failureCSCvr34759

static PSW multicast video session does not update correct source ip in "show fpgavideo filter"

CSCvr12898

RPD6.4 code takes longer to detect keepalive timeout, then RPD6.3CSCvp34556



viavi clc HA showing captured spectrum shifted to right by about 15MhzCSCvq11034





















RPHY: rpd stuck at init(l2tp) after DHCP renew fail and got a new IP addressCSCvq14646

TACACS support: Disable/enable local access based on TACACS reachabliliyCSCvq67634

Default PTP announce interval config on RPD should be 0 not 1CSCvq93216



Invalid REGPROC caller error due to pilottone codeCSCvp53392

Enter "ctrl+s" in RPD CLI, 'i-search' will show upCSCvp86506

Duplicate option 32 sent in INFO REQUESTCSCvq03023

docsRphyPtpRpdPtpPortStatusPacketsReceived & sent return 0CSCvq10038










Release Notes for Cisco Remote PHY Device, Cisco 1x2 / … · CHAPTER 1 Introduction...

Documents

Transcript of Release Notes for Cisco Remote PHY Device, Cisco 1x2 / … · CHAPTER 1 Introduction...