REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325...
-
date post
21-Dec-2015 -
Category
Documents
-
view
216 -
download
0
Transcript of REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325...
![Page 1: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/1.jpg)
REASSEMBLY and
INSTALLATION Chapter 12 Classroom
Manual Page 325
CBC AUTOMOTIVE
RK
![Page 2: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/2.jpg)
CHAPTER OBJECTIVES
Reassemble engine in a PROPER & ORGANIZED manner.
Install engine in vehicle. PRE-LUBE & make all adjustments
PRIOR to starting engine. Inspect & Complete the job.
CBC AUTOMOTIVE
RK
![Page 3: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/3.jpg)
CHAPTER INTRODUCTION
To be sure engine is CLEAN! Low quality cores
.030” undersize crankshafts .060” oversize bores
CBC AUTOMOTIVE
RK
![Page 4: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/4.jpg)
WARRANTY
Some engine warranties are as little as 90 days or 4000
A longer warranty usually means a higher price.
CBC AUTOMOTIVE
RK
![Page 5: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/5.jpg)
HOSES
All hoses that are not in excellent shape must be replaced.
FUEL COOLANT WATER PUMP
RADIATOR VACUUM EMISSION
CBC AUTOMOTIVE
RK
![Page 6: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/6.jpg)
REASSEMBLY 1
Before reassembly inspect and count all new parts.
Thoroughly clean block with hot soapy water.
Install Cam Bearings Install Soft Plugs Finger start all bolts before
torqueing them down.
CBC AUTOMOTIVE
RK
![Page 7: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/7.jpg)
REASSEMBLY 2
Coat the Cam with engine assembly lube
Install the Cam make sure the cam can be turned
by hand. Remove old crank sprocket and
Install new one.
CBC AUTOMOTIVE
RK
![Page 8: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/8.jpg)
REASSEMBLY 3 Install Main Bearing halves with oil holes
in block. Clean crank with carb cleaner and blow
dry. Coat Lower main bearing halves with
assembly lube. Make sure oil hole in bearing and block
align. Plastigauge each main bearing.
CBC AUTOMOTIVE
RK
![Page 9: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/9.jpg)
4 INSTALL CAM DRIVE
Install timing chain and cam gear, align marks.
Check manual for how to align marks. Turn engine two complete revolutions Check marks again. Degree in performance camshafts. Loctite bolts and torque to specks.
CBC AUTOMOTIVE
RK
![Page 10: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/10.jpg)
5 INSTALL TIMING COVER
If engine uses fuel pump eccentric, install it.
If engine uses a slinger install before cover.
Install timing cover seal, and lube lip with grease.
CBC AUTOMOTIVE
RK
![Page 11: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/11.jpg)
6 INSTALL THE DAMPER
Check for slipped outer ring. Check keyway. Check for groove worn in damper
from seal. If grooved, Replace damper, or
install speedy sleeve. Use special tool to pull damper onto
crankshaft.
CBC AUTOMOTIVE
RK
![Page 12: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/12.jpg)
7 INSTALL THE PISTONS Turn #1 crank pin to TDC. Install rings on piston separate ring gaps. Install rod bearings, install hoses on
bolts. Oil cylinder and piston with clean engine
oil. Adjust ring compressor. Install piston and rod assembly.
CBC AUTOMOTIVE
RK
![Page 13: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/13.jpg)
8 CHECK CLEARANCES
Check rod bearing clearance with Plastigauge.
Check rod side clearance with feeler gauge.
Check deck height with depth mic.
CBC AUTOMOTIVE
RK
![Page 14: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/14.jpg)
10 INSTALL THE OIL PUMP
Prime the pump. Make sure screen is clean, or
better replace it. Make sure screen is properly
positioned.
CBC AUTOMOTIVE
RK
![Page 15: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/15.jpg)
11 INSTALL OIL PAN
Apply RTV to corners where cork & rubber gaskets meet.
Straighten bolt flange if necessary Oil pan and screen must match.
CBC AUTOMOTIVE
RK
![Page 16: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/16.jpg)
12 INSTALL CYLINDER HEADS
Be sure gasket is installed in the right direction.
Make sure dowels are in the block, NOT the head.
If no dowels make alignment studs. Page 374 figure 13.19 (b)
CBC AUTOMOTIVE
RK
![Page 17: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/17.jpg)
12 INSTALL OHC HEADS
Place # 1 Piston at TDC. Turn Cam until its timing mark is
properly located. Page 375 figure 13.20 (a) Ensure valves will not hit pistons.
CBC AUTOMOTIVE
RK
![Page 18: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/18.jpg)
13 INSTALL HEAD BOLTS
Clean head bolt threads with a wire wheel.
Torque bolts in proper sequence. Apply sealer to bolts taped into
water jackets.
CBC AUTOMOTIVE
RK
![Page 19: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/19.jpg)
14 INSTALL VALVE TRAIN PARTS
Use assembly lube to coat lifter bottoms and sides.
Make sure they are free in their bores. Do NOT prefill lifters. Install pushrods & Rocker Arms Lube
all wear points. Make sure shafts are installed with
the correct side up.
CBC AUTOMOTIVE
RK
![Page 20: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/20.jpg)
15 INSTALL VALVE TRAIN PARTS
Use assembly lube to coat lifter bottoms and sides.
Make sure they are free in their bores. Do NOT prefill lifters. Install pushrods & Rocker Arms Lube
all wear points. Make sure shafts are installed with
the correct side up.
CBC
AUTOMOTIVE
RK
![Page 21: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/21.jpg)
16 INSTALL THE OIL PUMP
Prime the pump. Make sure screen is clean. Make sure screen is properly
positioned.
CBC
AUTOMOTIVE
RK
![Page 22: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/22.jpg)
17 INSTALL TIMING COVER
If engine uses fuel pump eccentric, install it.
If engine uses a slinger install before cover.
Install timing cover seal, and lube lip with grease.
CBC
AUTOMOTIVE
RK
![Page 23: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/23.jpg)
18 INSTALL THE DAMPER
Check for groove worn in damper from seal.
If grooved, Replace damper, or install speedy sleeve.
Use special tool to pull damper onto crankshaft.
CBC
AUTOMOTIVE
RK
![Page 24: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/24.jpg)
19 INSTALL OIL PAN
Apply RTV to corners where cork & rubber gaskets meet.
Straighten bolt flange if necessary Oil pan and screen must match.
CBC
AUTOMOTIVE
RK
![Page 25: REASSEMBLY and INSTALLATION u Chapter 12 u Classroom Manual u Page 325 CBCAUTOMOTIVERKCBCAUTOMOTIVERK.](https://reader031.fdocuments.net/reader031/viewer/2022032704/56649d595503460f94a38cd5/html5/thumbnails/25.jpg)
20 VALVE ADJUSTMENT
Adjust mechanical valves HOT. Adjust hydraulic valves on a V
engine with intake off.
CBC
AUTOMOTIVE
RK