Quick Installation Guide

Super 8 Roll Film Digitizer

COMPONENTS Front (Figure 1): 1) Supply Reel (Arm) 2) Take-up Reel (Arm) 3) Feed Sprocket 4) Forward Button • Press briefly (1 sec)—feeding frame one by one, • Press and hold (more then 3 seconds)--- Continuously

feeds the frames 5) Stop Button 6) Rewind Button • Press briefly (1 sec)— feeding frame one by one, • Press and hold (more then 3 seconds) ---

Continuously feeds the frames 7) Film Rollers 8) Film Cleaner 9) Power Button

Back (Figure 2): 10) DC power 11) USB 2.0 port

5) Stop Button

6) Rewind Button

9) Power Button

7) Film Rollers

4) Forward Button

Figure 1

Figure 2 11) USB 2.0 port

10) DC power

3

2) Take-up Reel (Arm)

3) Up Feed Sprocket

8) Film Cleaner

1) Supply Reel (Arm)

3) Down Feed Sprocket

Super 8 scanner Quick guide Before Installing Scanner

Check your Super 8 Film Reel, Film and Hard Disk Space Film Reel : Super 8 Scanner support 1”~8” standard Super 8 film reel Film: 1. Please make sure your film is smooth, if not

please use cutter to repair and maintain to smooth (Fig 1, 2)

2. If your film is splicing, please check as below list before you insert film

• splicing parts and film hold are smooth • The cement is fully dry

or will damage super 8 scanner

3. Please use special solvent with Super 8 Scanner or will damage your film.

Reel Type Super 8 Film at 18 frames

/second

Super 8 Film at 24frames

/second

Hard Disk Space

50 feet (15 meters) 3.5 min 2.5 min 1 GB (0.45 GB

for movie) 200 feet (60 meters) 13 min 10 min 4 GB (1.8 GB for

movie) 300 feet (90 meters) 20 min 15 min 6 GB (2.7 GB for

movie) 400 feet (120 meters) 26 min 20 min 8 GB (3.6 GB For

movie) 600 feet (180meters) 40 min 30 min 12 GB (5.4 GB

movie)

Hard Disk Space:

○ х х ○ х х

Fig. 1 Fig. 2

Super 8 scanner Quick guide Calibration Light Source (First time use)

Open the Case

Turn on Power

Connect to USB to PC

Wait for LED light to turn Orange

Activate the CyberView S8

Software

1

2

3

4

5

6

7

Create a New Movie Plan and click “Next” button

click “Calibration” button

After Finish Calibration click “OK” button

Super 8 scanner Quick guide Install Super 8 Scanner

Open the Case

Open the Reel Arm

Install movie film reel to Supply Reel Arm and Take-up Reel Arm

Turn on Power

Install film to Super 8 Scanner (Please see “How to install film”)

Connect to USB to PC

Wait for LED light to turn Orange

Activate the CyberView S8

Software

Start to Digitize Your Super 8 Movie

1

2

3 4

5

6

7

8

9

Make Sure the Reel is securely installed

Super 8 scanner Quick guide How to install film to Super 8 Scanner

Turn on Power

Install movie film reel to Supply Reel Arm and Take-up Reel Arm

Press and hold Forward Button

Feeding film into Up Feed Sprocket

Film auto feeds out from Down Feed Sprocket

Feeding film into the Film Rollers

Feeding film into the Take-up Reel

Click Stop Button

Start to Digitize Your Super 8 Movie

1

2

3

4 5

6

7

8

Feed Direction

Film Hold Lock your film onto the Take-up

Reel

Push Locked

Press the Forward Button until film is rolling tight then press Stop

Button 9

Scroll film until a sufficient length to Take-up Reel then press Stop

Button

Super 8 scanner Quick guide How to clean your film with Super 8 Scanner

Turn on Power

Install movie film reel to Supply Reel Arm and Take-up Reel Arm

Press and hold the Forward Button Feed Film through the wool felt

Click Clean Button to start cleaning your

film

1

2

3

Open the cover of the Film Cleaner

Add cleaning solvent to Wool Felt

4

5

6

Feeding film into the Take-up Reel

Click Stop Button

Activate the CyberView S8

Software

7

8

9

10

Installing the CyberView S8 Software 1. Install the CyberView S8 2. Connect the USB to the PC 3. Push the Power Button to turn the unit on 4. Install film to S8 Digitizer 5. Open the CyberView S8 Create a new movie 1. Choose “Create Your Movie Plan name” 2. Type the plan name 3. Choose the default export folder 4. Click the “Start Your Plan” to start digitizing Continue an existing movie plan 1. Choose “continue movie plan” 2. Browse to the existing folder and choose ”plan.ini “ 3. Click the “Start Your Plan” to continue digitizing

CyberView S8 Software Quick guide

Capture interface 1. Check the preview window 2. Click “up” and “down” to check your first

capture frame 3. Click “Capture” to start digitizing S8 movie 4. After you finish digitizing the S8 movie, the

software will auto stop capture (this is not the last step in the process)

5. Click next to watch your movie

Preview Widow

Frame Control button

Capture Button

Digitized frame counting Relapsed time

CyberView S8 Software Quick guide

Auto Brightness Brightness adjustment bar

Calibration

Auto Contrast

Combine interface 1. Check the preview window 2. Choose your super 8 movie frame rate(18 or 24

frame rate/ sec) 3. Click apply button to preview digitized frames 4. Choose output size “1080p” or “720p” 5. Click “Combine” to transfer frame to movie 6. After finishing the movie transfer, you can click “see

your movie” to watch digitized super 8 movie

Preview Widow

Output Size

Combine

Frame Rate

CyberView S8 Software Quick guide

Watch Video

Advanced Setting More detail operation function, setting and troubleshooting please check user manual (in Cyberview S8 CD) or go to reflecta website www.reflecta.de

CyberView S8 Software Quick guide