QB_M6
-
Upload
yet-fernandez -
Category
Documents
-
view
25 -
download
2
Transcript of QB_M6
MODULE 6: Worked-out Problems Problem 1:
For laminar free convection from a heated vertical surface, the local convection coefficient may be expressed as hx=Cx -1/4, where hx is the coefficient at a distance x from the leading edge of the surface and the quantity C, which depends on the fluid properties, is independent of x.
Obtain an expression for the ratio , where is the average coefficient between the leading edge (x=0) and the x location. Sketch the
variation of hx and with x.
xx hh /
xh
xh
Schematic:
Boundary layer,hx=C x
-1/4 w here C is a constant
Ts
x
Analysis: It follows that average coefficient from 0 to x is given by
x1/4
x
x
0
1/4x
0
xx
h3
4Cx
3
4x3/4
x
C
3
4h
dxxx
Cdxh
x
1h
Hence 3
4
h
h
x
x
The variation with distance of the local and average convection coefficient is shown in the sketch.
xx hh
xx hh3
4
4/1Cxhx
Comments: note that x =4/3, independent of x. hence the average
coefficients for an entire plate of length L is =4/3L, where hL is the local coefficient at x=L. note also that the average exceeds the local. Why?
hhx /
Lh
Problem 2:
Experiments to determine the local convection heat transfer coefficient for uniform flow normal to heated circular disk have yielded a radial Nusselt number distribution of the form
n
oD r
ra1
k
h(r)DNu
Where n and a are positive. The Nusselt number at the stagnation point is correlated in terms of the Reynolds number (ReD=VD/) and Prandtl
0.361/2Do Pr0.814Re
k
0)Dh(rNu
Obtain an expression for the average Nusselt number, , corresponding to heat transfer from an isothermal disk. Typically boundary layer development from a stagnation point yields a decaying convection coefficient with increasing distance from the stagnation point. Provide a plausible for why the opposite trend is observed for the disk.
kDhNuD /
Known: Radial distribution of local convection coefficient for flow normal to a circular disk.
Find: Expression for average Nusselt number. Schematic:
Assumptions: Constant properties.
Analysis: The average convection coefficient is
o
o
s
r
0
no
2n2
3o
no0
r
02o
A
ss
2)r(n
ar
2
r
r
kNuoh
]2π2πr)a(r/r[1NuD
k
πr
1h
hdAA
1h
Where Nuo is the Nusselt number at the stagnation point (r=0).hence,
0.361/2D
o
r
o
2n2
o
Pr2)]0.841Re2a/(n[1NuD
2)]2a/(n[1NuNuD
ro
r
2)(n
a
2
r/ro2Nu
k
DhNuD
o
Comments: The increase in h(r) with r may be explained in terms of the sharp turn, which the boundary layer flow must take around the edge of the disk. The boundary layer accelerates and its thickness decreases as it makes the turn, causing the local convection coefficient to increase.
Problem 3: In a flow over a surface, velocity and temperature profiles are of the forms
u(y)=Ay+By2-Cy3 and T(y)=D+Ey+Fy2-Gy3
Where the coefficients A through G are constants. Obtain expressions for friction coefficients Cf and the convection coefficient h in terms of u∞, T∞ and appropriate profile coefficients and fluid properties. Known: form of the velocity and temperature profiles for flow over a surface. Find: expressions for the friction and convection coefficients. Schematic:
u∞,T∞
T(y)=D+Ey+Fy2-Gy3
Ts=T(0)=D
U(y)=Ay-By2-Cy
3
y y
Analysis: The shear stress at the wall is
.]32[ 02
0
ACyByAy
uy
y
s
Hence, the friction coefficient has the form,
2f
22s
f
u
2AνC
ρu
2Aμ
/2ρu
τC
The convection coefficient is
TD
Ekh
TD
]3Gy2Fy[Ek
TT
y)T/(kh
f
0y2
f
s
0yf
Comments: It is a simple matter to obtain the important surface parameters from knowledge of the corresponding boundary layers profile. However is rarely simple matter to determine the form of the profile.
Problem 4: In a particular application involving airflow over a heated surface, the boundary layer temperature distribution may be approximated as
v
yuPrexp1
TT
TT
s
s
Where y is the distance normal to the surface and the Prandtl number, Pr=cp/k=0.7, is a dimensionless fluid property. If T∞ =400K, Ts=300K, and u∞/v=5000m-1, what is the surface heat flux? Known: Boundary layer temperature distribution Find: Surface heat flux. Schematic:
)Prexp(1)(
yu
TT
TyT
s
s
Properties: Air ( ): k = 0.0263 W/m.k kTS 300
Analysis: Applying the Fourier’s law at y=0, the heat flux is
0y
s
0y
"s ν
yuPrexp
ν
uPr)Tk(T
y
Tkq
ν
u)PrTk(Tq s
"s
1/m0.7x5000.K(100K)0.02063w/mq"s
Comments: (1) Negligible flux implies convection heat transited surface (2) Note use of k at to evaluate from Fourier’s law. sT "
sq
Problem 5:
Consider a lightly loaded journal bearing using oil having the constant properties =10-2 kg/s-m and k=0.15W/m. K. if the journal and the bearing are each mentioned at a temperature of 400C, what is the maximum temperature in the oil when the journal is rotating at 10m/s?
Known: Oil properties, journal and bearing temperature, and journal speed for lightly loaded journal bearing. Find: Maximum oil temperature. Schematic:
Assumptions: (1) steady-state conditions, (2) Incompressible fluid with constant properties, (3) Clearances is much less than journal radius and flow is Couette. Analysis: The temperature distribution corresponds to the result obtained in the text example on Couette flow.
22
o L
y
L
yU
2k
μTT(y)
The position of maximum temperature is obtained from
22
L
2y
L
1U
2k
μ0
dy
dT
y=L/2. Or, The temperature is a maximum at this point since hence 0.T/dyd 22
22
2 U8k
μTo
4
1
2
1U
2k
μToT(l/2)axTm,
C40.83T
0.15W/m.K8
/s)kg/s.m(10m10C40T
max
22
max
Comments: Note that Tmax increases with increasing µ and U, decreases with increasing k, and is independent of L.
Problem 6: Consider two large (infinite) parallel plates, 5mm apart. One plate is stationary, while the other plate is moving at a speed of 200m/s. both plates are maintained at 27C. Consider two cases, one for which the plates are separated by water and the other for which the plates are separated by air.
For each of the two fluids, which is the force per unit surface area required to maintain the above condition? What is the corresponding requirement? What is the viscous dissipation associated with each of the two fluids? What is the maximum temperature in each of the two fluids?
Known: conditions associated with the Couette flow of air or water. Find: (a) Force and power requirements per unit surface area, (2) viscous dissipation,(3) maximum fluid temperature. Schematic:
Assumptions: (1) Fully developed Couette flow, (2) Incompressible fluid with constant properties. Properties: Air (300K); µ=184.6*10-7 N.s/m2, k=26.3*10-3W/m.K; water (300K): µ=855*10—6N.s/m2,k=0.613W/m.K Analysis: (a) the force per unit area is associated with the shear stress. Hence, with the linear velocity profile for Couette flow τ=µ (du/dy) = µ (U/L).
34.2N/m0.005m
200m/sN.s/m10855 τ : Water
0.738N/m0.005m
200m/sN.s/m10184.6 τ : Air
226-water
227-air
With the required power given by P/A= .U
6840W/m200m/s)(34.2N/m(P/A) :Water
147.6W/m200m/s)(0.738N/m(P/A) :Air22
water
22air
(b) The viscous dissipation is .henceμ(U/L)μ(du/dy)μ 22
W/m101.370.005m
200m/sN.s/m10855 (μμφ : Water
W/m102.950.005m
200m/sN.s/m10184.6 (μμφ : Air
362
26-water
342
27-air
The location of the maximum temperature corresponds to ymax=L/2. Hence Tmax=To+µU2/8k and
C34.0K80.613W/m.
(200m/s)2N.s/m10855C27(T : Water
C30.5K0.0263W/m.8
(200m/s)2_N.s/m10184.6C27)(T : Air
26-
watermax)
2-7
airmax
Comments: (1) the viscous dissipation associated with the entire fluid layer, ),(LA must equal the power, P.
(2) Although aterw )( >> air )( , kwater>>kair. Hence, Tmax,water Tmax,air .
Problem 7: A flat plate that is 0.2m by 0.2 m on a side is orientated parallel to an atmospheric air stream having a velocity of 40m/s. the air is at a temperature of T=20C, while the plate is maintained at Ts=120C. The sir flows over the top and bottom surfaces of the plate, and measurement of the drag force reveals a value of 0.075N. What is the rate of heat transfer from both sides of the plate to the air?
Known: Variation of hx with x for flow over a flat plate. Find: Ratio of average Nusselt number for the entire plate to the local Nusselt number at x=L. Schematic:
Analysis: The expressions for the local and average Nusselt number are
2.NuL
NuL
andk
2CL
k
(L)2CLNuL
Hence
2CLLL
2Cdxx
L
Cdxh
L
1h
wherek
LhNu
k
CL
k
)L(CL
k
LhNu
-
1/21/2-
1/21/2L
0
1/2L
0
xL
LL
1/21/2L
L
Comments: note the manner in which is defined in terms of . Also note that
-NuL Lh
L
0
xL dxNuL
1Nu
Problem 8:
For flow over a flat plate of length L, the local heat transfer coefficient hx is known to vary as x-1/2, where x is the distance from the leading edge of the plate. What is the ratio of the average Nusslet number for the entire plate to the local Nusslet number at x=L (NuL)?
Known: Drag force and air flow conditions associated with a flat plate. Find: Rate of heat transfer from the plate. Schematic:
Assumptions: (1) Chilton-Colburn analogy is applicable. Properties: Air(70C,1atm): =1.018kg/m3, cp=1009J/kg.K, pr=0.70, =20.22*10-6m2/s. Analysis: the rate of heat transfer from the plate is
)T(T(L)h2q s2
Where may be obtained from the Chilton-Colburn analogy, h
240Wq
C20)(120.K)(0.3m)2(30W/mq
is rateheat The
.K30W/mh
2/3.70)9J/kg.K)(0)40m/s(100(1.018kg/m105.76h
Prcρu2
Ch
hence,
105.76/2(40m/s)1.018kg/m
(0.2m)(0.075N/2)
2
1
/2ρu
τ
2
1
2
C
Prcρu
htPrS
2
Cj
22
2-
34-
2/3p
f-
4
23
2
2
sf
2/3
p
2/3fH
Comments: Although the flow is laminar over the entire surface ( , the pressure gradient is zero and the Chilton-Colburn analogy is applicable to average, as well as local, surface conditions. Note that the only contribution to the drag force is made by the surface shear stress.
)100.4/1022.20/2.0/40/Re 526 smmsmLuL
Problem 9:
Consider atmospheric air at 25C in parallel flow at 5m/s over both surfaces of 1-m-long flat plate maintained at 75C. Determine the boundary layer thickness, the surface shear stress, and the heat flux at the trailing edge. Determine the drag force on the plate and the total heat transfer from the plate, each per unit width of the plate.
Known: Temperature, pressure, and velocity of atmospheric air in parallel flow over a Plate of prescribed length and temperature. Find: (a) Boundary layer thickness, surface shear stress and heat flux at trailing edges, (b) drag force and total heat transfer flux per unit width of plate.
Schematic:
Fluid
∞=5m/sT∞=25C
P∞=1 atm L=1m
x)
Ts=75°C
Assumptions: (1) Critical Reynolds number is 5*105, (2) flow over top and bottom surfaces Properties: (Tf=323K, 1atm) Air: =1.085kg/m3,=18.2*10-6m2/s,k=0.028W/m.K,pr=0.707 Analysis: (a) calculate the Reynolds number to know the nature of flow
526L 102.75/sm1018.2
m1m/s5
ν
LuRe
Hence the flow is laminar, and at x=L
22Ls,
1/2523
1/2L
2Ls,
1/251/2L
0.0172N/m.s0.0172kg/mτ
)1050.664/(2.7(5m/s)m
kg
2
1.085/2)0.664Re(ρρτ
9.5mm)101m/(2.7555LReδ
Using the correct correlation,
22s
2L
1/31/21/31/2L
LL
C)217W/m25C.K(754.34W/m)ThL(Ts(L)q"
.K4.34W/m8W/m.K)/1m155.1(0.02h
hence,
155.1(0.707)105)0.332(2.75Pr0.332Rek
hLNu
(b) The drag force per unit area plate width is where the factor of two is
included to account for both sides of the plate. Hence with LsLD
2'
868W/mC25).K(75/m2(1m)8.68W)T(T2Lhq
.K8.68W/m2hLh with also
0.0686N/m3N/m2(1m)0.034D
0.0343N/mτ
is drag The
)101.328(2.75/2)(5m/s)(1.085kg/m/2)1.328Re(ρρτ
2s
-
L"
2-
L
2'
2Ls
1/25231/2L
2Ls
Problem 10: Engine oil at 100C and a velocity of 0.1m/s flows over both surfaces of a 1-m-long flat plate maintained at 20C. Determine
a. The velocity and thermal boundary thickness at the trailing edge. b. The local heat flux and surface shear stress at the trailing edge. c. The total drag force and heat transfer per unit area width of the plate.
Known: Temperature and velocity of engine oil Temperature and length of flat plate. Find: (a) velocity and thermal boundary thickness at the trailing edge, (b) Heat flux and surface shear stress at the trailing edge, (c) total drag force and heat transfer per unit plate width.
Schematic:
Assumptions: engine oil (Tf=33K): =864kg/m3,=86.1*106m2/s, k=0.140W/m /K, Pr=1081. Analysis: (a) calculate the Reynolds number to know the nature of flow
1161/sm10*86.1
1m0.1m/s
ν
LuReL
26-
Hence the flow is laminar at x=L, and
0.0143m)0.147(1081δPrδ
0.147m)5(1m)(11615LReδ1/31/3
t
1/21/2L
(b) The local convection coefficient and heat flux at x=L are
22s
21/31/31/2LL
1300W/mC100).K(2016.25W/m)ThL(Tq"
.K16.25W/m)(1081)0.332(11611m
0.140W/m.KPr0.3325LRe
L
kh
Also the local shear stress is
22Ls
1/223
1/2L
2Ls
0.0842N/m.s0.0842kg/mτ
)0.664(1161(0.1m/s)2
864kg/m/2)0.664Re(ρρτ
(c) With the drag force per unit width given by where the factor of 2 is
included to account for both sides of the plate, is follows that LsLD
2'
5200W/mC100).K(20/m2(1m)32.5W)T(Th2Lq
that follows alsoit .K,32.5W/m2hh with
0.673N/m)1.328(1161(0.1m/s)/m2(1m)864kg/2)1.328Re(ρρτ
2sL
_
2LL
_
1/2231/2L
2Ls
Comments: Note effect of Pr on (/t).
Problem 11:
Consider water at 27C in parallel flow over an isothermal, 1-m-long, flat plate with a velocity of 2m/s. Plot the variation of the local heat transfer coefficient with distance along the plate. What is the value of the average coefficient?
Known: velocity and temperature of air in parallel flow over a flat plate of prescribed length.
Find: (a) variation of local convection coefficient with distance along the plate, (b) Average convection coefficient.
Schematic:
Assumptions: (1) Critical Reynolds number is 5*105. Properties: Water (300K): =997kg/m3,=855*10-6N.s/m2, =/=0.858*10-6m2/s, k=0.613W/m. K, Pr=5.83 Analysis: (a) With
526L 102.33/sm100.858
1m2m/s
ν
LuRe
Boundary layer conditions are mixed and
4055 4240 4491 4871 5514 .K)(W/mh
1.0 0.8 0.6 0.4 0.0215 x(m)
xPrν
u0.0296kPr0.0296Re
x
khx 0.215m,xfor
1206 1768 hx(W/m2.K)
0.215 0.1 x(m)
xPrν
u0.332kPr0.332Re
x
khx 0.215m,x for
0.215m)10/2.33101m(5)/ReL(Rex
x
0.21/3
4/5
1/34/5x
1/21/3
1/2
1/31/2x
65Lcx,c
2
The Spatial variation of the local convection coefficient is shown above (b) The average coefficient is
.K4106W/mh
871(5.83))1033[0.0379(2.1m
0.613W/m.K871)Pr(0.037Re
L
kh
2L
_
1/34/561/34/5LL
_
Problem 12: A circular cylinder of 25-mm diameter is initially at 150C and is quenched by immersion in a 80C oil bath, which moves at a velocity of 2m.s in cross flow over the cylinder. What is the initial rate of heat loss unit length of the cylinder?
Known: Diameter and initial temperature of a circular cylinder submerged in an oil bath f prescribed temperature and velocity. Find: initial rate of heat loss unit per length.
Schematic:
Assumptions: (1) Steady-state conditions, (2) uniform surface temperature. Properties: Engine oil (T=353K): =38.1*10-6m2/s, k=0.138W/m. K, Pr=501; (Ts=423K): Prs=98. Analysis: The initial heat loss per unit length is
8.8W/mC80)0.025m(150π.K1600W/mq'
.K1600W.mh
98
501(501)0.26(1312)
0.025m
0.138W/m.K)1/4/Pr(PrPrCRe
D
kh
hence . 7.4 table from 0.6m and 0.26C Find
1312/sm1038.1
m)2m/s(0.025
ν
VDRe
when relation. Zhukauskas the from computed be may where
)TπD(Thq
2
2_
1/40.370.6
snm
D
_
26D
s
_
_
h
Comments: Evaluating properties at the film temperature, Tf=388K(=14.0*10-6m2/s, k=0.135W/m. K, Pr=196), find ReD=3517.
Problem 13: An uninsulated steam pipe is used to transport high-temperature steam from one building to one another. The pipe is 0.5-m diameter, has a surface temperature of 150C, and is exposed to ambient air at -10C.the air moves in cross flow over the pipe with a velocity of 5m.s.What is the heat loss per unit length of pipe?
Known: Diameter and surface temperature of uninsulated steam pipe. Velocity and temperature of air in cross flow. Find: Heat loss per unit length.
Schematic:
V=5m/sT∞=263K
Air D=0.5mm
Ts=150 C
Assumptions: (1) steady-state conditions, (2) uniform surface temperature Properties: Air (T=263K, 1atm):=12.6*10-6m2/s, k=0.0233W/m. K, Pr=0.72;(Ts=423K, 1atm); Prs=0.649. Analysis: the heat loss per unit length is
)TπD(Thq s
_
.K1600W.mh
98
501(501)0.26(1312)
0.025m
0.138W/m.K)1/4/Pr(PrPrCRe
D
kh
hence . 7.4 table from 0.6m and 0.26C Find
1312/sm1038.1
m)2m/s(0.025
ν
VDRe
when relation. Zhukauskas the from computed be may where
2_
1/40.370.6
snm
D
_
26D
_
h
Hence the heat rate is
4100W/mC10)(-0.5m(150π.K16.3W/mq' 2 Comments: Note that q’Dm, in which case the heat loss increases significantly with increasing D.
Problem 14:
Atmospheric air at 25C and velocity of 0.5m/s flows over a 50-W incandescent bulb whose surface temperature is at 140C. The bulb may be approximated as a sphere of 50-mm diameter. What is the rate of heat loss by convection to the air?
Known: Conditions associated with airflow over a spherical light bulb of prescribed diameter and surface temperature.
Find: Heat loss by convection.
Schematic:
Assumptions: (1) steady-state conditions, (2) uniform surface temperature.
roperties: Air (Tf=25C, 1atm): =15.71*10 m /s, k=0.0261W/m. /K.Pr=.
Analysis:
-6 2P
0.71,=183.6*10-7N.s/m2; Air (Ts=140C, 1atm): =235.5*10-7N.s/m2
)TπD(Thq s _
10.3WC25)(140π(0.05m).Km
W11.4q
is rateheat the and
.K11.4W/mh
235.5
183.6](0.71)0.06(1591)[0.4(1591)2
0.05m
K0.0261W/m.h
hence
1591/sm1015.71
0.05m0.5m/s
ν
VDRe
Where
])(μμ/)Pr0.06Re(0.4Re[2D
kh
when relation. Whitaker the from computed be may where
22
2_
1/40.42/31/2
_
26D
1/4s
0.42/3D
1/2D
_
_
h
Comments: (1) The low value of suggests that heat transfer by free convection may be significant and hence that the total loss by convection exceeds 10.3W
_
h
(2) The surface of the bulb also dissipates heat to the surroundings by radiation. Further, in an actual light bulb, there is also heat loss by conduction through the socket. (3) The Correlation has been used its range of application (/s )<1.
Problem 15:
Water at 27 C flows with a mean velocity of 1m/s through a 1-km-long cast iron pipe at 0.25 m inside diameter.
(a) Determine the pressure drop over the pipe length and the
corresponding pump power requirement, if the pipe surface is clean.
(b) If the pipe surface roughness is increased by 25% because of contamination, what is the new pressure drop and pump power requirement.
Known: Temperature and velocity of water in a cast iron pipe of prescribed dimensions. Find: pressure drops and power requirement for (a) a clean surface and (b) a surface with a 25% larger roughness.
Schematic:
Assumptions: (1) Steady, fully developed flow. Properties: Water (300K):=1000 kg/m3, =855*10-6 N.s/m2. Analysis: (a) from eq.8.22, the pressure drop is
L2D
ρufΔp
2m
e=2.6*10-4 m for clean cast iron; hence e/D=1.04*10-3. With
5326
mD 102.92
/1000kg/mN.s/m10855
0.25m1m/s
ν
DuRe
0.42barN/m104.2P
.mkg/s104.21000m2(0.25m)
(1m/s)(1000kg/m0.021P
, hence 0.021.fthat 8.3 fig from find
24
2423
)
The pump power requirement is
2.06kW1m/s/4)m0.25(πN/m104.2P
/4)uΔp(πDVΔp.P
2224
m2
.
(b) Increasing by 25% it follows that =3.25*10-4m and e/D=0.0013. With ReD unchanged, from fig 8.3, it follows that f 0.0225. Hence
2.21kW)P/f(fP bar 0.45)Δ/f(fΔP 1122122 1p Comments: (1) Note that L/D=4000>>(xfd,h/D) 10 for turbulent flow and the assumption of fully developed conditions is justified. (2) Surface fouling results in increased surface and increases operating costs through increasing pump power requirements.
Problem 16:
Consider flow in a circular tube. Within the test section length (between 1 and 2) a constant heat flux q”s is maintained.
(a) For the two cases identified, sketch, qualitatively, the surface
temperature Ts(x) and the fluid mean temperature Tm(x) as a function of distance along the test section x. in case A flow is hydro dynamically and thermally fully developed. In case B flow is not developed.
(b) Assuming that the surface flux q”s and the inlet mean temperature Tm,1 are identical for both cases, will the exit mean temperature Tm,2 for case A be greater than, equal to , or less than Tm,2 for case B? Briefly explain why?
Known: internal flow with constant surface heat flux, . "
sq
Find: (a) Qualitative temperature distributions (x), under developing and fully developed flow, (b) exit mean temperature for both situations. Schematic:
Flow
1 2
q”s=constant
Assumptions: (a) Steady-state conditions, (b) constant properties, (c) incompressible flow. Analysis: Based upon the analysis, the constant surface heat flux conditions,
constantdx
dTm
Hence, regardless of whether the hydrodynamic or thermal boundary layer is fully developed, is follows that Tm(x) is linear T m,2 will be the same for all flow conditions. The surface heat flux can be written as
(x)]Th[Tq ms"s
Under fully developed flow and thermal conditions, h=hfd is a constant. When flow is developing h> hfd . Hence, the temperature distributions appear as below.
Problem 17:
A thick-walled, stainless steel (AISI 316) pipe of inside and outside diameter Di=20mm and Do=40m is heated electrically to provide a
uniform heat generation rate of . The outer surface of the pipe is insulated while water flows through the pipe at a rate of
36.
/10 mWq
skgm /1.0.
(a) If the water inlet temperature is Tm,1=20C and the desired outlet temperature is Tm,o=40C, what is the required pipe length
(b) What are the location and value of the maximum pipe temperature?
Known: Inner and outer diameter of a steel pipe insulated on the outside and experiencing uniform heat generation. Flow rate and inlet temperature of water flowing through the pipe. Find: (a) pipe length required to achieve desired outlet temperature, (b) location and value of maximum pipe temperature. Schematic:
Assumptions: (1) steady-state conditions, (2) constant properties, (3) negligible kinetic energy, potential energy and flow work changes, (4) one-dimensional radial conduction in pipe wall, (5) outer surface is adiabatic.
Properties: Stainless steel 316 (T 400K): k=15W/m.k; water ( ); cp=4178J/kg. K, k=0.617W/m. K,=803*10-6N.s/m2, Pr=5.45
303KT.
m
Analysis: (a) performing an energy balance for a control volume about the inner tube, it follows that
8.87mL
](0.02)4m(ππ/4)[(0.W/m10
C)20178(J/kg.K(0.1kg/s)4
)LD(ππ/4)(q
)T(TmcL
)LD(ππ/4)(qq)T(Tcm
22362i
20
.
.
im,om,p
2i
20
.
im,om,p
.
(b) The maximum wall temperature exists at the pipe exit (x=L) and the insulated surface (r=ro). The radial temperature distribution in the wall is of the form
Tnr 2k
qr -r
4k
qC Cnr
2k
qrr
4k
q-T)T(r :rr
2k
qrC
r
Cr
2k
q0
dr
dT ;rr
; conditions boundary the gconsiderin
CnrCr4k
qT(r)
si
.2o2
i
.
22i
.2o2
i
.
si1
.2o
1o
1o
.
rro
212
.
o
The temperature distribution and the maximum wall temperature (r=ro) are
)Th(T4D
)D(Dq
LπD
)LDq(π(π/4)q
from followsit exit,at wall the of temperture surafaceinner the Ts, where
Tr
rn
2k
qr )r-(r
4k
q-)T(rT
Tr
rn
2k
qr )r-(r
4k
qT(r)
om,si
2i
2o
.
i
.2i
2o"
s
si
o
.2o2
i2o
.
omaxw,
si
.2o2
i2
.
Where h is the local convection coefficient at the exit. With
7928N.s/m103π(0.02m)80
0.1kg/s4
μπD
m4Re
26i
.
D
The flow is turbulent and, with (L/Di)=(8.87m/0.02m)=444>>(xfd/D)10,it is also fully developed. Hence, from the Dittus-Boelter correlation,
.K1840W/m5.45)0.023(79280.02m
0.617W/m.K)pr(0.023Re
D
kh 20.44/50.44/5
Di
Hence the inner surface temperature of the wall at the exit is
C52.4C48.20.01
0.02n
215W/m.K
(0.02)W/m10](0.01)[(0.02)
415W/m.K
W/m10T
and
C48.2C40.K(0.02m)180W/m4
](0.02m)[(0.04m)W/m10T
4D
)D(Dq
23622
36
maxw,
2
2236
om,i
2i
2o
.
s
T
Comments: The physical situation corresponds to a uniform surface heat flux, and Tm increases linearly with x. in the fully developed region, Ts also increases linearly with x.
T
xfd
Ts(x)
Tm(x)
x
Problem 18: The surface of a 50-mm diameter, thin walled tube is maintained thin walled tube is maintained at 100C. In one case air is cross flow very the tube with a temperature of 25C and a velocity of 30m/s. In another case air is in fully developed flow through the tube with a temperature of 25C and a mean velocity of 30m/s. compare the heat flux from the tube to the air for the two cases.
Known: surface temperature and diameter of a tube. Velocity and temperature of air in cross flow. Velocity and temperature of air in fully developed internal flow. Find: convection heat flux associated with the external and internal flows. Schematic:
Air
Um=30m/sTm=25°C
V=30m/sT =25 C
Ts=100 C
D=0.05m
Air
Assumptions: (1) steady-state conditions, (2) uniform cylinder surface temperature, (3) fully developed internal flow Properties: Air (298K): =15.71*10-6m2/s, k=0.0261W/m.K, Pr=0.71 Analysis: for the external and internal flow
426
1055.9/1071.15
05./30Re
sm
msmDuVD mD
From the Zhukauskas relation for the external flow, with C=0.26 and m=0.6
223)1()71.0()1055.9(26.0)PrPr(Pr/Re 4/137.06.044/1_
smDD CuN
Hence, the convection coefficient and heat rate are
232"
2__
/1073.8)25100(./4.116)(
./4.11622305.0
./0261.0
mWCkmWTThq
KmWm
KmWNuD
D
kh
s
Using the Dittus-Boelter correlation, for the internal flow, which is Turbulent,
232
__
4.05/4244.05/4_
/1058.7)25100(./101)(
.2/10119305.0
./0261.0
193)71.0()1055.9(023.0PrRe023.0
mWCKmWTTh
KmWKmW
NuD
kh
NU
ms
D
DD
"q
isflux heat the and
Comments: Convection effects associated with the two flow conditions are comparable.
Problem 19: Cooling water flows through he 25.4 mm diameter thin walled tubes of a stream condenser at 1m/s, and a surface temperature of 350K is maintained by the condensing steam. If the water inlet temperature is 290 K and the tubes are 5 m long, what is the water outlet temperature? Water properties may be evaluated at an assumed average temperature of 300K Known: Diameter, length and surface temperature of condenser tubes. Water velocity and inlet temperature. Find: Water outlet temperature. Schematic:
L=5m
D=0.0254m
Tm,i=290KUm=1m/s
Ts=350K
Assumptions: (1) Negligible tube wall conduction resistance, (2) Negligible kinetic energy, potential energy and flow work changes. Properties: Water (300K):=997kg/m3, cp=4179J/kg.K, =855*10-6kg/s.m,k=0.613W/m.K, Pr=5.83 Analysis:
29,618kg/s.m10855
54m(1m/s)0.02997kg/m
μ
DρuRe
]h)cm(ππDL)exp[T(TTT
6
3m
D
_
p
.
im,ssom,
The flow is turbulent. Since L/D=197, it is reasonable to assume fully developed flow throughout the tube. Hence
323KK)(4179J/kg.(0.505kg/s
.K)5m(4248W/mπ(0.0254m)(60K)exp350KT
0.505kg/s4m)m/s)(0.025(1/m(ππ/4)997k/4)(ππρum
With
.K4248W/m4m)/m.K/0.025176(0.613WNuD(k/D)h
2
om,
232m
.
2_
Comments: The accuracy of the calculations may be improved slightly by
reevaluating properties at . 306.5KT_
m
Problem 20: The air passage for cooling a gas turbine vane can be approximated as a tube of 3-mm diameter and 75-mm length. If the operating temperature of the vane is 650C, calculate the outlet temperature of the air if it enters the tube at 427C and 0.18kg/h. Known: gas turbine vane approximation as a tube of prescribed diameter and length maintained at an known surface temperature. Air inlet temperature and flow rate. Find: outlet temperature of the air coolant. Schematic:
hkgm /18.0.
Assumptions: (1) Steady-state conditions, (2) negligible Kinetic and potential energy changes.
Properties: Air (assume : cp=1094J/kg. K, k=0.0563 W/m.
K, =363.7*10-7 N.s/m2, Pr=0.706; Pr=0.706;(Ts=650C=923K, 1atm): =404.2*10-7N.s/m2.
)1,780_
atmKTm
Analysis: For constant wall temperatures heating,
.
_
,
, exp
pims
oms
mc
hPL
TT
TT
Where P=D. for flow in circular passage,
N.s/m103.7π(0.03m)36
/3600s/h)0.18kg/h(14
πDμ
m4Re
7
.
D
The flow is laminar, and since L/D=75mm/3mm=25, the Sieder-Tate correlation including combined entry length fields.
.K87.5W/m10404.2
10363.7
25
0.7065841.86
0.003m
K0.0563W/m.h
μ
μ
L/D
PrRe1.86
k
DhNu
2
0.14
7
71/3_
0.14
s
1/3
D
__
D
Hence, the air outlet temperature is
1094J/kg.K)kg/s(0.18/3600
.K87.5W/m0.075mπ(0.003m)exp
C427)(650
T650 2om,
Tm,o=578C
Comments: (1) based upon the calculations for Tm,o=578C, =775K which is in good agreement with our assumption to evaluate the thermo physical properties.
_
mT
Problem 21 A household oven door of 0.5-m height and 0.7-m width reaches an average surface temperature of 32C during operation. Estimate the heat loss to the room with ambient air at 22C. If the door has an emissivity of 1.0 and the surroundings are also at 22C, comment on the heat loss by free convection relative to that by radiation.
Known: Oven door with average surface temperature of 32C in a room with ambient temperature at 22C. Find: Heat loss to the room. Also, find effect on heat loss if emissivity of door is unity and the surroundings are at 22C.
Schematic:
0.7m
L=
0.5m
Assumptions: (1) Ambient air in quiescent, (2) surface radiation effects are negligible. Properties: Air (Tf=300K, 1atm): =15.89*10-6 m2/s, k=0.0263W/m. K, =22.5*10-6 m2/s, Pr=0.707, =1/Tf=3.33*10-3K-1
Analysis: the heat rate from the oven door surface by convection to the ambient air is
)T(TAhq ss
_
Where can be estimated from the free convection correlation for a vertical plate,
_
h
2
8/279/16
1/6L
__`
(0.492/Pr)1
0.387Ra0.825
k
LhLNu
The Rayleigh number,
4
2626
322s
L 101.142/sm1022.5/sm1015.89
m322)K0.52(1/300k))39.8m/s
να
)LT(TgRa
Substituting numerical values into equation, find
.K3.34W/m63.5
0.5m
K0.0263W/m.LNu
Lh
63.5(0.492/Pr)1
)1020.387(1.140.825
k
LhLNu
2_`_
2
8/279/16
1/88_
_`
kL
The heat rate using equation is
11.7W22)K(320.7)m.k(0.53.34W/mq 22
Heat loss by radiation, assuming =1 is
21.4W]k22)(27332)[(273.KW/m5.67100.7)m1(0.5q
)Tσ(TεAq4244282
rad
4sur
4ssrad
Note that heat loss by radiation is nearly double that by free convection. Comments: (1) Note the characteristics length in the Rayleigh number is the height of the vertical plate (door).
Problem 22
An Aluminum alloy (2024) plate, heated to a uniform temperature of 227C, is allowed to cool while vertically suspended in a room where the ambient air and surroundings are at 27C. The late is 0.3 m square with a thickness of 15 mm and an emissivity of 0.25.
a. Develop an expression for the time rate of change of the plate temperature assuming the temperature to be uniform at any time.
b. Determine the initial rate of cooling of the plate temperature is 227C.
c. Justify the uniform plate temperature assumption. Known: Aluminum plate alloy (2024) at uniform temperature of 227C suspended in a room where the ambient air and the surroundings are at 27C
Find: (1) expression for the time rate of change of the plate, (2) Initial
rate of cooling (K/s) when the plate temperature is 227C. (3) justify the
uniform plate temperature assumption.
Schematic:
Properties: Aluminium alloy 2024 (T=500K):=2270 kg/m3,
k=186W/m.K, c=983 J/kg.K; Air (Tf=400K, 1atm):=26.41*10-
6m2/s,k=0.0338 W/m.K,=38.3*10-6 m2/s, Pr=0.690.
Analysis :( a) from an energy balance on the plate considering free
convection and radiation exchange . ..
stout EE
)Tεσ(T)T(Th[c
2
dt
dTor
dt
dTρA)Tσ(Tε2A)T(T2Ah 4
sur4ssL
.
cs4sur
4ssss
_
L
Where Ts is the plate temperature assumed to be uniform at any time.
(b) To evaluate (dt/dx), estimate . Find first the Rayleigh number _
Lh
82626
322s
L 101.308/sm10.33/sm1026.41
0.3m27)K27(1/400k)(29.8m/s
να
)LT(TgRa
8
Substituting numerical values, find
5.55)
4/99/16
82
4/99/16
1/4L
_`
90)(0.492/0.61
1080.670(1.300.68
(0.492/Pr)1
0.670Ra0.68LNu
0.099K/s
)K300.K)(500W/m100.25(5.6727)K.K(2276.25W/m983J/kg.K0.015m2770Kg/m
2
dt
dT
.K6.25W/mK/0.3m0.0338W/m.55.5k/LNuh
44282
3
2_`
L
_
(c) The uniform temperature assumption is justified if the Biot number
criterion is satisfied. With )/A.(A)(V/AL sssc
_
1.0/ k
and . Using the linearized radiation coefficient
relation find,
___
, hBihhh totradconvtot
.K3.86W/m3002)K300)(5002)(500.K8W/m100.25(5.67)T)(TTεσ(Th 23422
sur2
ssursrad
_
Hence Bi=(6.25+3.86) W/m2.k (0.015m)/186W/m. K=8.15*10-4. Since
Bi<<0.1, the assumption is appropriate.
Problem 23 The ABC Evening News Report in news segment on hypothermia research studies at the University of Minnesota claimed that heat loss from the body is 30 times faster in 1 0C water than in air at the same temperature. Is that a realistic statement?
Known: Person, approximated as a cylinder, experiencing heat loss in water or air at 10C.
Find: Whether heat loss from body in water is 30 times that in air. Assumptions: (1) Person can be approximated as a vertical cylinder of diameter D=0.3 m and length L=1.8m, at 25C, (2) Loss is only from the lateral surface.
Properties: Air (_
T =(25+10) C/2=290K, 1atm); K=0.0293 W/m. K, ==19.91*10-6m2/s, =28.4*10-6 m2/s; Water (290K); k=0.598 W/m.K; =vf=1.081*10-6m2/s, =k vf /cp =1.431*10-7m2/s, f=174*10-6K-1.
Analysis: in both water (wa) an air(a), the heat loss from the lateral surface of the cylinder approximating the body is
)TDL(Thq s
_
Where Ts and T are the same for both situations. Hence,
_
a
wa
_
a
wa
h
h
q
q
Vertical cylinder in air:
9
2626
323
L 105.228/sm28.410/sm10*19.91
10)k(1.8m)5(1/290K)(29.8m/s
να
gββΔTRa
.K2.82W/mh 173.4)100.1(5.228CRak
LhNu
1/3,n and 0.1C with
2L
_1/39n
L
__
LL
Vertical cylinder in water.
112726
3162
L 109.643/sm101.431/sm101.081
10)K(1.8m)(25K101749.8m/sRa
.K328W/mh 978.9)100.1(9.643CRak
hLNu
1/3,n and 0.1C with
2L
_1/311n
L
__
L
Hence, from this analysis we find
30 of claim the with poorly compares which 117.K2.8W/m
.K328W/m
q
q2
2
a
wa
Problem 24 In a study of heat losses from buildings, free convection heat transfer from room air at 305 K to the inner surface of a 2.5-m-high wall at 295 K is simulated by performing laboratory experiments using water in a smaller test cell. In the experiments the water and the inner surface of the test cell are maintained at 300 and 290K, respectively. To achieve similarity between conditions in the room and the test cell, what is the required test cell height? If the average Nusselt number for the wall may be correlated exclusively in terms of the Rayleigh number, what is the ratio f the average convection coefficient for the room wall to the average coefficient for the test cell wall? Known: Air temperature and wall temperature and height for a room. Water temperature and wall temperature for a simulation experiment. Find: Required test cell height for similarity. Ratio and height convection coefficient for the two cases. Schematic:
L a=
2.5m L
w
Assumptions: (1) Air and water are quiescent; (2) Flow conditions correspond to free convection boundary layer development on an isothermal vertical plate, (3) constant properties. Properties: Air (Tf =300K, 1 atm); K=0.0293 W/m.K, ==15.9*10-6m2/s, =22.5*10-6 m2/s; =1/Tf=3.33*10-3K-1, k=0.0263W/m.K; water (Tf=295K):ρ=998kg/m3, =959*10-6N.s/m2, cp=4181 J/kg.K, =227.5*10-
6K-1, k=0.606 W/m.K; Hence =/ ρ =9.61/s, =k / ρ cp =1.45*10-7m2/s.
Analysis: Similarity requires that RaL,a=RaL,w where
mmL
oHL
L
hence
w
a
airw
a
w
45.0)179.0(5.2
10*228.0
10*33.3
10*5.22*9.15
10*45.1*61.9
)(
)(
,
)L-T(TgRa
3
3
12
143/1
2
3s
L
3
w
a
a
w
w
_
_
a
_
wL,
_
aL,wL,aL,
10*7.810.606
0.0263
2.5
0.45
k
k
L
L
h
h
.henceNuNu that followsit ,RaRa if
Comments: Similitude allows us to obtain valuable information for one system by performing experiments for a smaller system and a different fluid.
Problem 25
square plate of pure aluminum, 0.5 m on a side and 16 mm hick, is
nown: Initial temperature and dimensions of an aluminum plate.
ind: (a) initial cooling rate, (2) validity of assuming negligible temperature
chematic:
Ainitially at 300C and is suspended in a large chamber. The walls of the chamber are maintained at 27C, as is the enclosed air. If the surface emissivity of the plate temperature during the cooling process? Is it reasonable to assume a uniform plate temperature during the cooling process? KConditions of the plate surroundings. Fgradients in the plate during the cooling process. S
L
ssumptions: (1) plate temperature is uniform; (2) chamber air is quiescent,
roperties: Aluminum (573k); k=232W/m.k, cp=1022J/kg.K, ρ=2702 kg/m3:
nalysis: (a) performing an energy balance on the plate,
A(3) Plate surface is diffuse-gray, (4) Chamber surface is much larger than that of plate, (5) Negligible heat transfer from edges. PAir (Tf=436K, 1 atm):υ=30.72*10-6m2/s,α=44.7*10-6m2/s,k=0.0363W/m.K, Pr=0.687, β=0.00229K-1. A
psurss
pstsurss
wcTTTThAdtdT
dtdTVcETTTThAq
/)]4()([2/
]/[)]4()([2
4_
.4
_
8
2626
323s
L 105.58/sm017.44/sm10*30.72
)K(0.5m)721(300-0.00229K9.8m/s)L-T(TgRa
KmWh
Ra
L
kh L
./8.5
])687.0/492.0(1[
)1058.5(670.068.0
5.0
0363.0
]Pr)/492.0(1[
670.068.0
2_
9/416/9
4/18
9/416/9
4/1_
ence the initial cooling rate is H
sKdt
dT
kkgJmmkg
KKKmWCKmW
dt
dT
/136.0
./1022)016.0(/2702
])300()573[(./1067.525.0)27300(./8.523
444282
) To check the Validity of neglecting temperature gradients across the
nd the assumption is excellent.
omments: (1) Longitudinal (x) temperature gradients are likely to me more
(bplate thickness, calculate
22" ./0.11273//)14131583()/( /)2/( kmWKmWTTqhwherekwhBi itoteffeff
A
4-103.832W/m.K(0.008m)/2(11W/m2.K)Bi hence
Csevere than those associated with the plate thickness due to the variation of h with x. (2) Initially q”conv q”rad.
Problem 26
eer in cans 150 mm long and 60 mm in diameter is initially at 27C and is
nown: Dimensions and temperature of beer can in refrigerator
ind: orientation which maximum cooling rate.
Schematic:
Bto be cooled by placement in a refrigerator compartment at 4C. In the interest of maximizing the cooling rate, should the cans be laid horizontally or vertically in the compartment? As a first approximation, neglect heat transfer from the ends. Kcompartment. F
Air,T∞=4°CP=1 atmD=0.06m
Horizontal, (h) Vertical, (V)Ts=27 C
L=150m
m
Assumptions: (1) End effects are negligible, (2) Compartment air is
roperties: Air (Tf=288.5K, 1 atm): υ=14.87*10-6 m2/s, k=0.0254W/m.K,
nalysis: The ratio of cooling rates may be expressed as
quiescent, (3) constant properties. Pα=21.0*10-6m2/s, Pr=0.71, β=1/Tf=3.47*10-3K-1. A
h
v
s
s
h
v
qh
v
h
h
TT
TT
DL
DL
h
hq_
_
_
_
)(
)(
For the vertical surface, find
639L
39326-26-
-1-323s
L
1044.8)15.0(105.2Ra
L105.2L/s)m10/s)(21m10(14.87
C)(23K103.479.8m/s)L-T(TgRa
Using the correct correlation
KmWm
KmW
L
kNuhh
NuL
LvL ./03.515.0
./0254.07.29 hence,
7.29])71.0/492.0(1[
)1044.8(387.0825.0
2___
2
27/816/9
6/16
Using the correct correlation,
97.018.5
03.5,
./18.506.0
./0254.024.12
24.12])71.0/559.0(1[
)104.5(387.060.0
2___
2
27/861/9
6/15_
h
v
DhD
D
q
qhence
KmWm
KmW
D
kNuhh
Nu
Comments: in view of the uncertainties associated with equations and the neglect of end effects, the above result is inconclusive. The cooling rates are are approximately the same.