PRODUCTION ESTIMATION BASED ON CUTTING THEORIES … · Author: Dr.ir. S.A. Miedema PRODUCTION...
38
Author: Dr.ir. S.A. Miedema PRODUCTION ESTIMATION BASED ON CUTTING THEORIES FOR CUTTING WATER SATURATED SAND Dr.ir. S.A. Miedema 1 ABSTRACT In dredging, the excavation of soil is one of the most important processes. It is known that on the largest cutter suction dredges thousands of kW’s are installed on the cutter drive. To predict the forces on excavating elements, two-dimensional cutting theories are used. Van Os 1977 [9], Verruijt 1985 [11], Miedema 1987 [6] and 1989 [7] and Van Leussen & Van Os 1987 [10] described the two-dimensional cutting theory for water saturated sand and its applications extensively. The aim of developing such theories is to predict the loads on excavating elements like cutterheads, dragheads, etc. It is however also possible to predict the production, when the soil mechanics parameters, the geometry of the excavating element and the available power, are known. The soil mechanics parameters are described by Van Leussen & Nieuwenhuis in 1984 [5]. The cutting process of a cutterhead is very complicated. Not only do the blades have a three-dimensional shape; also, the velocities on the blades are three-dimensional, with respect to their direction, due to a combination of the swing velocity and the circumferential velocity. Other excavating elements such as dredging wheels, blades in dragheads and trenchers, may not look that complicated, but will also require the three- dimensional cutting theory to fully describe the cutting process. In 1994, Miedema [8] described the three-dimensional cutting theory. To derive forces, torque, power, specific energy and production from the above-mentioned theories, requires complicated calculations, while the soil mechanics parameters of the sand have to be known. Mostly, only the SPT value of the sand is known. This paper describes the two- and three- dimensional cutting theory in water saturated sand. A calculation model is derived on how to determine the most essential parameters, to be able to calculate the specific energy and the production if the SPT value of the sand is known. Verification for both the two- and the three dimensional cutting theories and the SPT model is given based on laboratory tests with straight blades. The laboratory tests give a good correlation between calculated and measured cutting forces for both the two- and the three dimensional cutting theory and show that the approach for production estimation based on SPT values gives an upper limit for the specific energy and a lower limit for the production. For a more accurate prediction of the production however, more detailed soil mechanics parameters should be known. 1 Mekelweg 2, 2628 CD Delft, The Netherlands; Email: [email protected] Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995. Copyright: Dr.ir. S.A. Miedema
Transcript of PRODUCTION ESTIMATION BASED ON CUTTING THEORIES … · Author: Dr.ir. S.A. Miedema PRODUCTION...
Author: Dr.ir. S.A. Miedema
PRODUCTION ESTIMATION BASED ON CUTTING THEORIES FOR CUTTING WATER SATURATED SAND
Dr.ir. S.A. Miedema1
ABSTRACT
In dredging, the excavation of soil is one of the most important processes. It is known that on the largest cutter suction dredges thousands of kW’s are installed on the cutter drive.
To predict the forces on excavating elements, two-dimensional cutting theories are used. Van Os 1977 [9], Verruijt 1985 [11], Miedema 1987 [6] and 1989 [7] and Van Leussen & Van Os 1987 [10] described the two-dimensional cutting theory for water saturated sand and its applications extensively. The aim of developing such theories is to predict the loads on excavating elements like cutterheads, dragheads, etc. It is however also possible to predict the production, when the soil mechanics parameters, the geometry of the excavating element and the available power, are known. The soil mechanics parameters are described by Van Leussen & Nieuwenhuis in 1984 [5].
The cutting process of a cutterhead is very complicated. Not only do the blades have a three-dimensional shape; also, the velocities on the blades are three-dimensional, with respect to their direction, due to a combination of the swing velocity and the circumferential velocity. Other excavating elements such as dredging wheels, blades in dragheads and trenchers, may not look that complicated, but will also require the three-dimensional cutting theory to fully describe the cutting process. In 1994, Miedema [8] described the three-dimensional cutting theory. To derive forces, torque, power, specific energy and production from the above-mentioned theories, requires complicated calculations, while the soil mechanics parameters of the sand have to be known. Mostly, only the SPT value of the sand is known.
This paper describes the two- and three- dimensional cutting theory in water saturated sand. A calculation model is derived on how to determine the most essential parameters, to be able to calculate the specific energy and the production if the SPT value of the sand is known. Verification for both the two- and the three dimensional cutting theories and the SPT model is given based on laboratory tests with straight blades.
The laboratory tests give a good correlation between calculated and measured cutting forces for both the two- and the three dimensional cutting theory and show that the approach for production estimation based on SPT values gives an upper limit for the specific energy and a lower limit for the production. For a more accurate prediction of the production however, more detailed soil mechanics parameters should be known.
1 Mekelweg 2, 2628 CD Delft, The Netherlands; Email: [email protected]
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
INTRODUCTION
In 1975 Hatamura and Chijiiwa [11] distinguished 3 failure mechanisms in soil cutting. The "shear type", the "flow type" and the "tear type". A fourth failure mechanism can be distinguished, the "curling type", as is known in metal cutting. Although it seems that the curling of the chip cut is part of the flow of the material, whether the "curling type" or the "flow type" occurs depends on several conditions. The "flow type", "tear type" and "curling type" occur in clay, while the "tear type" and, under high hydrostatic pressure, the "flow type" occur when cutting rock. The "shear type" occurs in materials with an angle of internal friction, but without cohesion like sand. Figure 1 illustrates the 4 failure mechanisms as they might occur when cutting soil.
Figure 1. The failure mechanisms.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Although the "shear type" is not a continuous cutting process, the shear planes occur so frequently, that a continuous process is considered. The Mohr-Coulomb failure criteria is used to derive the cutting forces. This derivation is made under the assumption that the stresses on the shear plane and the blade are constant and equal to the average stresses acting on the surfaces.
To estimate the production in water saturated sand, first a summary of the two-dimensional cutting theory is given. Secondly, this theory is extended for angled (deviated) blades. Finally relations found in literature are used to correlate SPT values with soil mechanical parameters in order to calculate the specific energy required to cut the sand and from this an estimation of the production is made.
THE TWO-DIMENSIONAL CUTTING THEORY FOR WATER SATURATED SAND
THE EQUILIBRIUM OF FORCES The forces acting on a straight blade when cutting soil, can be distinguished as (fig. 3): 1. A force normal to the blade N2. 2. A shear force S2 as a result of the soil/steel friction N2 tan[δ]. 3. A shear force A as a result of pure adhesion between the soil and the blade. This force
can be calculated by multiplying the adhesive shear strength of the soil with the contact area between the soil and the blade.
4. A force W2 as a result of water under pressure on the blade. These forces are shown in figure 3. If the forces N2 and S2 are combined to a resulting force K2 and the adhesive force and the water under pressures are known, then the resulting force K2 is the unknown force on the blade. Figure 2 illustrates the forces on the layer of soil cut. The forces shown are valid in general. In sand several forces can be neglected. The forces acting on this layer are: 1. The forces occurring on the blade as mentioned above. 2. A normal force acting on the shear surface N1. 3. A shear force S1 as a result of internal fiction N1 tan[φ]. 4. A force W1 as a result of water under pressure in the shear zone. 5. A shear force C as a result of pure cohesion. This force can be calculated by
multiplying the cohesive shear strength with the area of the shear plane. 6. A gravity force G as a result of the weight of the layer cut. 7. An inertial force I, resulting from acceleration of the soil.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 2. The forces on the layer cut.
Figure 3. The forces on the blade.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
The normal force N1 and the shear force S1 can be combined to a resulting grain force K1. By taking the horizontal and vertical equilibrium of forces, an expression for the force K2 on the blade can be derived. The horizontal equilibrium of forces:
( ) ( ) ( ) ( ) ( )( ) ( ) 0sinKsinW
cosAcosIcosCsinWsinK
22
11
=δ+α⋅−α⋅+
α⋅−β⋅+β⋅+β⋅−φ+β⋅ (1)
The vertical equilibrium of forces:
( ) ( ) ( ) ( )( ) ( ) ( ) 0cosKcosWsinA
GsinIsinCcosWcosK
22
11
=δ+α⋅−α⋅+α⋅+
+β⋅+β⋅+β⋅+φ+β⋅− (2)
The force K2 on the blade is now:
( ) ( )( )
( ) ( ) ( ) ( )( )δ+φ+β+α
φ+β+α⋅−φ⋅+φ⋅+φ+β⋅+
φ+δ+β+αφ⋅+φ+β+α⋅
=
sincosAcosCcosIsinG
sinsinWsinWK 12
2 (3)
From this last equation, the forces on the blade can be derived. On the blade, a force component in the direction of cutting velocity Fh and a force perpendicular to this direction Fv can be distinguished.
( ) ( ) ( )α⋅+δ+α⋅+α⋅−= cosAsinKsinWF 22h (4)
( ) ( ) ( )α⋅−δ+α⋅+α⋅−= sinAcosKcosWF 22v (5) From literature, it is known that, during the process of cutting sand, the pore volume of the sand increases. This is caused by the phenomenon dilatancy (see figure 4). With a certain cutting velocity, vc there has to be a flow of water to the shear zone, the area where the pore volume increases. This causes a decrease in the pore pressure of the pore water and because the soil stress remains constant, the grain stress will increase. Van Os [9] 1977 stated: "If it is the aim of the engineer to know the average cutting farces needed to push the blade through the soil, he can take an average deformation rate ∂e/∂t to insert into the Biot equation. But it should be noted that this is purely practical reasoning and has nothing to do with Theoretical Soil Mechanics". Van Os and Van Leussen published their cutting theory in 1987 [10]. Van Leussen and Nieuwenhuis [5] discussed the relevant soil mechanical parameters in 1984. Miedema [6] 1987 uses the average deformation rate as stated by Van Os [9] 1977 but instead of inserting this in the Biot equation; the average deformation rate is modelled as a boundary condition in the shear zone.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 4. Dilatation during the cutting of water saturated sand. Although the cutting process is not solely dependent upon the phenomenon dilatancy, the above mentioned research showed that for cutting velocities in a range from 0.5 to 5 m/sec the cutting process is dominated by the phenomenon dilatancy, so the contributions of gravitational, cohesive, adhesive and inertial forces can be neglected, thus:
( ) ( )( )φ+δ+β+α
φ+β+α⋅+φ⋅=
sinsinWsinWK 21
2 (6)
This gives for the horizontal and vertical force on the blade:
( ) ( )δ+α⋅+α⋅−= sinKsinWF 22h (7)
( ) ( )δ+α⋅+α⋅−= cosKcosWF 22v (8)
THE WATER PORE PRESSURES The forces W1 and W2 resulting from the pore pressures are the unknowns in the equations 6, 7 and 8. Miedema [6] 1987 calculated the average pore pressures P1 and P2 with a Finite Element Method (FEM) program (fig. 5). With the equations 9 and 10 the forces W1 and W2 can be determined by substituting the results of the FEM calculations.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 5. Pore pressure distribution & location of transducers.
( ) ( )β⋅⋅+⋅⋅⋅⋅⋅⋅ρ⋅
=sinkaka
bhevgpWmax2i1
2icw1
1 (9)
( ) ( )α⋅⋅+⋅⋅⋅⋅⋅⋅⋅ρ⋅
=sinkaka
bhhevgpWmax2i1
bicw22 (10)
On average P1 can be estimated by 0.15, P2 by 0.32, a1 by 0.5 and a2 by 0.5. When the pore pressures reach the water vapor pressure, cavitation will occur. The pore pressures cannot decrease further with an increasing cutting velocity and remain constant. In this case the forces W1 and W2 can be calculated analytical, giving:
( )( )β
⋅⋅+⋅⋅ρ=
sinbh10zgW iw
1 (11)
( )( )α
⋅⋅+⋅⋅ρ=
sinbh10zgW bw
2 (12)
THE SIMPLIFIED EQUATIONS FOR THE CUTTING FORCES
Miedema [6] 1987 simplified the equations by using proportionality coefficients c1, c2, d1 and d2 . This leads to the first two simplified equations for the two-dimensional cutting process in water saturated sand without cavitation:
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
m
2icw1
h kebhvgcF ⋅⋅⋅⋅⋅ρ⋅
= (13)
m
2icw2
v kebhvgcF ⋅⋅⋅⋅⋅ρ⋅
= (14)
With: max
imax
n1nne
−−
= and maxim k5.0k5.0k ⋅+⋅≈
For the cavitating cutting process the following equation are valid for the horizontal and vertical cutting force:
( ) bh10zgdF iw1h ⋅⋅+⋅⋅ρ⋅= (15)
( ) bh10zgdF iw2v ⋅⋅+⋅⋅ρ⋅= (16) The coefficients c1 , c2 , d1 and d2 are dependent upon the angle of internal friction of the sand φ, the soil interface friction angle δ, the blade angle α and the blade height/layer thickness ratio hb /hi. Detailed tables of c1 , c2 , d1 and d2 are published by Miedema [6] in 1987. Figure 6 shows the results of laboratory tests carried out by Bindt and Zwartbol [2] in 1994. The correlation between measurements and theory is satisfactory.
THE NORMAL AND FRICTION FORCES ON THE SHEAR SURFACE AND ON
THE BLADE Although the normal and friction forces as shown in figure 2 are the basis for the calculation of the horizontal and vertical cutting forces, the approach used, requires the following equations to derive these forces by substituting 13 and 14 for the non-cavitating cutting process or 15 and 16 for the cavitating cutting process. The index 1 points to the shear surface, while the index 2 points to the blade (fig. 8):
( ) ( )β⋅−β⋅= cosFsinFF vh1n (17)
( ) ( )β⋅+β⋅= sinFcosFF vh1f (18)
( ) ( )α⋅+α⋅= cosFsinFF vh2n (19)
( ) ( )α⋅−α⋅= sinFcosFF vh2f (20)
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 6. Snow-plough effect research, theory versus measurements. Blade width 0.3m, blade height 0.2m, layer thickness as above. Inclination angle 45
degrees, deviation angle 0 degrees.
THE THREE-DIMENSIONAL CUTTING THEORY The previous paragraphs summarized the two-dimensional cutting theory. On a cutterhead, the blades can be divided into small elements, at which a two dimensional cutting process is considered. However, this is correct only when the cutting edge of this
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
element is perpendicular to the direction of the velocity of the element. For most elements this will not be the case. This means the elements can be considered to be deviated (angled) with respect to the direction of the cutting velocity. A component of the cutting velocity perpendicular to the cutting edge and a component parallel (deviated) to the cutting edge can be distinguished. This second component results in a deviation force on the blade element, due to the friction between the soil and the blade. This force is also the cause of the transverse movement of the soil, the so called snow-plough effect. To predict the deviation force and the direction of motion of the soil on the blade, the equilibrium equations of force will have to be solved in three directions. Since there are four unknowns, three forces and the direction of the velocity of the soil on the blade, one additional equation is required. This equation follows from an equilibrium equation of velocity between the velocity of grains in the shear zone and the velocity of grains on the blade. Since the four equations are partly non-linear and implicit, they have to be solved iteratively, Miedema [8] 1994. Figure 7 shows this phenomenon. As with snow-ploughs, the sand will flow to one side while the blade is pushed to the opposite side. This will result in a third cutting force, the deviation force Fd. To determine this force, the flow direction of the sand has to be known. Figure 8 shows a possible flow direction.
Figure 7. The cutting process with deviated blades.
VELOCITY CONDITIONS For the velocity component perpendicular to the blade vc, if the blade has a deviation angle ι and a drag velocity vd according to figure 8, it yields:
( )ι⋅= cosvv dc (21) The velocity of grains in the shear surface perpendicular to the cutting edge is now:
( )( )β+αα
⋅=sin
sinvv c1r (22)
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
The relative velocity of grains with respect to the blade, perpendicular to the cutting edge is:
( )( )β+αβ
⋅=sin
sinvv c2r (23)
The grains will not only have a velocity perpendicular to the cutting edge, but also parallel to the cutting edge, the deviation velocity components vd1 on the shear surface and vd2 on the blade. The velocity components of a grain in x, y and z direction can be determined by considering the absolute velocity of grains in the shear surface, this leads to:
( ) ( ) ( )ι⋅+ι⋅β⋅= sinvcoscosvv 1dri1x (24)
( ) ( ) ( )ι⋅−ι⋅β⋅−= cosvsincosvv 1dri1y (25)
( )β⋅= sinvv 1r1z (26)
Figure 8. Velocity & force conditions.
The velocity components of a grain can also be determined by a summation of the drag velocity of the blade and the relative velocity between the grains and the blade, this gives:
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
( ) ( ) ( )ι⋅−ι⋅α⋅−= sinvcoscosvvv 2d2rd2x (27)
( ) ( ) ( )ι⋅+ι⋅α⋅−= cosvsincosvv 2d2r2y (28)
( )α⋅= sinvv 1r2z (29) Since both approaches will have to give the same resulting velocity components, the following condition for the transverse velocity components can be derived:
( )ι⋅=+===>= sinvvvvv d2d1d2x1x (30)
( )ι⋅=+===>= sinvvvvv d2d1d2y1y (31)
2z1z vv = (32)
THE DEVIATION FORCE
Since friction always has a direction matching the direction of the relative velocity between two bodies, the fact that a deviation velocity exists on the shear surface and on the blade, implies that also deviation forces must exist. To match the direction of the relative velocities, the following equation can be derived for the deviation force on the shear surface and on the blade (fig. 8):
1r
1d1f1d v
vFF ⋅= (33)
2r
2d2f2d v
vFF ⋅= (34)
Since perpendicular to the cutting edge, an equilibrium of forces exists, the two deviation forces must be equal in magnitude and have opposite directions.
2d1d FF = (35) By substituting 33 and 34 in 35 and then substituting 18 and 20 for the friction forces and 22 and 23 for the relative velocities, the following equation can be derived, giving a second relation between the two deviation velocities:
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
( ) ( )( ) ( )
( )( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛βα
⋅⎟⎟⎠
⎞⎜⎜⎝
⎛β⋅+β⋅α⋅−α⋅
=⎟⎟⎠
⎞⎜⎜⎝
⎛⋅⎟⎟⎠
⎞⎜⎜⎝
⎛=
sinsin
sinFcosFsinFcosF
vv
FF
vv
vh
vh
2r
1r
1f
2f
2d
1d (36)
To determine Fh and Fv the angle of internal friction φ and the soil/interface friction angle mobilized perpendicular to the cutting edge, have to be determined by using the ratio of the transverse velocity and the relative velocity, according to:
( ) ( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛⋅φ=φ
1r
1de v
vatncostantan (37)
( ) ( ) ⎟⎟⎠
⎞⎜⎜⎝
⎛⎟⎟⎠
⎞⎜⎜⎝
⎛⋅δ=δ
2r
2de v
vatncostantan (38)
THE RESULTING CUTTING FORCES
The resulting cutting forces in x, y and z direction can be determined once the deviation velocity components are known. However, it can be seen that the second velocity condition (36) requires the horizontal and vertical cutting forces perpendicular to the cutting edge, while these forces can only be determined if the mobilized friction angles (37 and 38) are known. This creates an implicit set of equations that will have to be solved by means of an iteration process. For the cutting forces on the blade the following equation can be derived:
( ) ( )ι⋅+ι⋅= sinFcosFF 2dh2x (39)
( ) ( )ι⋅−ι⋅= cosFsinFF 2dh2y (40)
v2z FF = (41) The results of cutting tests with a 45 degree blade with a deviation angle of 45 degrees are shown in figure 9. The correlation between the measurements and the theory is good. It should be noted that the specific energy is considerably smaller than in the tests with a deviation angle of 0 (fig. 6).
SPECIFIC ENERGY
To determine the production of excavating elements as a function of the SPT value of the soil, the specific energy method is used. The specific energy is the amount of energy (work) required for the excavation of 1 cubic meter of in-situ soil. The dimension of specific energy is kNm/m3 or kPa. The specific energy depends on the type of soil (soil mechanical parameters), on the geometry of the excavating element (dredging wheel,
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
crown cutter, etc.) and on the operational parameters (haulage velocity or trail velocity, revolutions, face geometry, etc).
Figure 9. Snow-plough effect research, theory versus measurements. Blade width 0.3m, blade height 0.2m, layer thickness as above. Inclination angle 45
degrees, deviation angle 45 degrees.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Beside the above, the effective specific energy will be influenced by other phenomena such as spill, wear and the bull-dozer effect. The maximum production can also be limited by the hydraulic system but this will not be considered in this paper. The production can be derived from the specific energy by dividing the available power by the specific energy.
s
a
EPQ = (42)
An accurate calculation of the specific energy and thus the production can be carried out only when all off the parameters influencing the cutting process are known. If an estimate has to be made of the specific energy and the production, based on the SPT value only, a number of assumptions will have to be made and a number of approximations will have to be applied. These assumptions and approximations will maximize the specific energy and thus minimize the production. In other words, the specific energy as calculated in this paper is an upper limit, whilst the calculated production is a lower limit. Wear, spill and limitations such as the bull-dozer effect are not taken into consideration. Once the specific energy and the production per 100 kW are known, the production, giving an available power, can be calculated. This production can be either realistic, meaning that the bull-dozer effect will not occur, or not realistic meaning that this effect will occur. In the last case, the maximum production will have to be calculated from the limitations caused by the bull-dozer effect. From the maximum production derived, the maximum swing velocity, giving a certain bank height and step size, can be determined. The type of cutting process is determined by the soil mechanical properties of the soil to be dredged, the geometry of the excavating element and the operational parameters. SPECIFIC ENERGY AND PRODUCTION IN SAND
As discussed previously, the cutting process in sand can be distinguished in a non-cavitating and a cavitating process, in which the cavitating process can be considered to be an upper limit to the cutting forces. Assuming that during an SPT test in water-saturated sand, the cavitating process will occur, because of the shock wise behavior during the SPT test, the SPT test will give information about the cavitating cutting process. Whether, in practice, the cavitating cutting process will occur, depends on the soil mechanical parameters, the geometry of the cutting process and the operational parameters. The cavitating process gives an upper limit to the forces, power and thus the specific energy and a lower limit to the production and will therefore be used as a starting point for the calculations. For the specific energy of the cavitating cutting process, the following equation can be derived according to Miedema [6, page 148]:
( ) 1ws d10zgE ⋅+⋅⋅ρ= (43)
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 10. Friction angle versus SPT value ([4] page 148). The production, for an available power Pa , can be determined by:
( ) 1w
a
s
a
d10zgP
EPQ
⋅+⋅⋅ρ== (44)
The coefficient d1 is the only unknown in the above equation. A relation between d1 and the SPT value of the sand and between the SPT value and the water depth has to be found. The dependence of d1 on the parameters α, hi en hb can be estimated accurately. For normal sands there will be a relation between the angle of internal friction and the soil interface friction. Assume blade angles of 30, 45 and 60 degrees, a ratio of 3 for hb /hi and a soil/interface friction angle of 2/3 times the internal friction angle. For the coefficient d1 the following equations are found by regression:
φ⋅⋅+−= 0444.01 e666.0185.0d (α = 30 degrees) (45)
φ⋅⋅++= 0597.0
1 e333.0304.0d (α = 45 degrees) (46)
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
φ⋅⋅++= 0818.01 e154.0894.0d (α = 60 degrees) (47)
With: φ = the angle of internal friction in degrees. Lambe & Whitman [4, page 78] (fig. 11) give the relation between the SPT value, the relative density and the hydrostatic pressure in two graphs. With some curve-fitting these graphs can be summarized with the following equation:
( )( ) 52.24 RD1010z221.082.1SPT ⋅⋅+⋅+= − (48)
Figure 11. SPT values versus relative density ([4] page 78).
Lambe & Whitman [4, page 148] (fig. 10) give the relation between the SPT value and the angle of internal friction, also in a graph. This graph is valid up to 12 m in dry soil. With respect to the internal friction, the relation given in the graph has an accuracy of 3 degrees. A load of 12 m dry soil with a density of 1.67 ton/m3 equals a hydrostatic pressure of 20 m.w.c. An absolute hydrostatic pressure of 20 m.w.c. equals 10 m of water depth if cavitation is considered. Measured SPT values at any depth will have to be
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
reduced to the value that would occur at 10 m water depth. This can be accomplished with the following equation (see fig. 12):
( ) z10 SPTz0354.0646.0
1SPT ⋅⋅+
= (49)
Figure 12. SPT values reduced to 10m water depth. With the aim of curve-fitting, the relation between the SPT value reduced to 10 m
water depth and the angle of internal friction can be summarized to:
10SPT01753.0e9.255.54 ⋅−⋅−=φ (+ 3 degrees value) (50) For water depths of 0, 5, 10, 15, 20, 25 and 30 m and an available power of 100 kW the production is shown graphically for SPT values in the range of 0 to 100 SPT. Figure 13 shows the specific energy and figure 14 the production for a 45 degree blade angle.
THE TRANSITION NON-CAVITATING/CAVITATING
Although the SPT value only applies to the cavitating cutting process, it is necessary to have a good understanding of the transition between the non-cavitating and the cavitating cutting process. Based on the theory in [6], an equation has been derived for this transition. If this equation is valid, the cavitating cutting process will occur.
( ) 1k
ehvc10zd
mic1
1 <⋅⋅⋅+⋅ (51)
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
The ratio d1/c1 appears to have an almost constant value for a given blade angle, independent of the soil mechanical properties. For a blade angle of 30 degrees this ratio equals 11.9. For a blade angle of 45 degrees this ratio equals 7.72 and for a blade angle of 60 degrees this ratio equals 6.14. The ratio e/km has a value in the range of 1000 to 10000 for medium to hard packed sands. At a given layer thickness and water depth, the transition cutting velocity can be determined using the above equation. At a given cutting velocity and water depth, the transition layer thickness can be determined.
Figure 13. Specific energy versus SPT value (45 deg. blade).
Figure 14. Production per 100kW versus SPT value (45 deg. blade).
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
CONCLUSIONS
To check the validity of the above derived theory, research has been carried out in the laboratory of the chair of Dredging Technology of the Delft University of Technology. The tests are carried out in a hard packed water saturated sand, with a blade of 0.3 m by 0.2 m. The blade had cutting angles of 30, 45 and 60 degrees and deviation angles of 0, 15, 30 and 45 degrees. The layer thicknesses were 2.5, 5 and 10 cm and the drag velocities 0.25, 0.5 and 1 m/s. Figure 6 shows the results with a deviation angle of 0 degrees, while figure 9 shows the results with a deviation angle of 45 degrees. The lines in this figure show the theoretical forces. As can be seen, the measured forces match the theoretical forces well. Based on two graphs from Lambe & Whitman [4] and an equation for the specific energy from Miedema [6], relations are derived for the SPT value as a function of the hydrostatic pressure and of the angle of internal friction as a function of the SPT value. With these equations also the influence of water depth on the production can be determined. The specific energies as measured from the tests are shown in figures 6 and 9. It can be seen that the deviated blade results in a lower specific energy. These figures also show the upper limit for the cavitating cutting process. For small velocities and/or layer thicknesses, the specific energy ranges from 0 to the cavitating value. The tests are carried out in a sand with an angle of internal friction of 40 degrees. According to figure 10 this should give an SPT value of 33. An SPT value of 33 at a waterdepth of about 0 m, gives according to figure 13, a specific energy of about 450-500 kPa. This matches the specific energy as shown in figure 6. All derivations are based on a cavitating cutting process. For small SPT values it is however not sure whether cavitation will occur. A non-cavitating cutting process will give smaller forces and power and thus a higher production. At small SPT values however the production will be limited by the bull-dozer effect or by the possible range of the operational parameters such as the cutting velocity. The calculation method used remains a lower limit approach with respect to the production and can thus be considered conservative. For an exact prediction of the production all of the required soil mechanical properties will have to be known. As stated, limitations following from the hydraulic system are not taken into consideration.
ACKNOWLEDGEMENTS The author wishes to thank mr. Zwartbol and mr. Bindt for the work they carried out on this research. He also thanks the Delft University for giving him the opportunity to carry out this research.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
BIBLIOGRAPHY
[ 1] Becker, S. & Miedema, S.A. & Jong, P.S. de & Wittekoek, S., "On the Closing Process of Clamshell Dredges in Water Saturated Sand". Proc. WODCON XIII, Bombay, India, 1992. And Terra et Aqua No. 49, September 1992, IADC, The Hague.
[ 2] Bindt, A., "Quantitative & Qualitative Research on the Snow Plough Effect in Water Saturated Sand. Report 94.3.GV.4336, Delft University of Technology, 1994.
[ 3] Hatamura, Y, & Chijiiwa, K., "Analyses of the mechanism of soil cutting". 1st report, Bulletin of the JSME, vol. 18, no. 120, June 1975. 2st report, Bulletin of the JSME, vol. 19, no. 131, May 1976. 3st report, Bulletin of the JSME, vol. 19, no. 139, November 1976. 4st report, Bulletin of the JSME, vol. 20, no. 139, January 1977. 5st report, Bulletin of the JSME, vol. 20, no. 141, March 1977.
[ 4] Lambe, T.W. & Whitman, R.V., "Soil Mechanics". John Wiley & Sons, New York, 1969-1979.
[ 5] Leussen, W. van & Nieuwenhuis J.D., "Soil Mechanics Aspects of Dredging". Geotechnique 34 No.3, pp. 359-381, 1984.
[ 6] Miedema, S.A., "The Calculation of the Cutting Forces when Cutting Water Saturated Sand, Basical Theory and Applications for 3-Dimensional Blade Movements with Periodically Varying Velocities for in Dredging Usual Excavating Elements" (in Dutch). PhD thesis, Delft, 1987, the Netherlands.
[ 7] Miedema, S.A., "On the Cutting Forces in Saturated Sand of a Seagoing Cutter Suction Dredger". Proc. WODCON XII, Orlando, Florida, USA, April 1989. And Terra et Aqua No. 41, December 1989, Elseviers Scientific Publishers.
[ 8] Miedema, S.A., "On the Snow-Plough Effect when Cutting Water Saturated Sand with Inclined Straight Blades". ASCE Proc. Dredging 94, Orlando, Florida, USA, November 1994.
[ 9] Os, A.G. van, "Behaviour of Soil when Excavated Underwater". International Course Modern Dredging. June 1977, The Hague, The Netherlands.
[10] Os, A.G. van & Leussen, W. van, "Basic Research on Cutting Forces in Saturated Sand". Journal of Geotechnical Engineering, Vol. 113, No.12, December 1987.
[11] Verruijt, A., "Offshore Soil Mechanics". Delft University of Technology, 1985-1994.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
LIST OF SYMBOLS USED a1, a2 Proportionality coefficients weighed permeability - A Adhesive force on the blade kN b Width of blade m c1, c2 Coefficients (no-cavitation) - C Cohesive force on shear plane kN d1, d2 Coefficients (cavitation) - e Volume strain % Es Specific energy kPa Fh Horizontal cutting force kN Ff1 Friction force on the shear surface kN Ff2 Friction force on the blade kN Fn1 Normal force on the shear surface kN Fn2 Normal force on the blade kN Fv Vertical cutting force kN Fd1 Deviation force on the shear surface kN Fd, d2 Deviation force on the blade kN Fx1, 2 Cutting force in x-direction kN Fy1, 2 Cutting force in y-direction kN Fz1, 2 Cutting force in z-direction kN g Gravitational constant (9.81) m/s² G Gravitational force kN hi Initial thickness of layer cut m hb Height of blade m ki Initial permeability m/s kmax Maximum permeability m/s km Average permeability m/s K1 Grain force on the shear plane kN K2 Grain force on the blade kN I Inertial force on the shear plane kN ni Initial porosity % nmax Maximum porosity % N1 Normal grain force on shear plane kN N2 Normal grain force on blade kN P1 Average pore pressure on the shear surface kPa P2 Average pore pressure on the blade kPa Pa Available power for cutting kW Q Production of in-situ soil m³/sec
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
RD Relative density % S1 Shear force due to internal friction on the shear surface kN S2 Shear force due to soil/steel friction on the blade kN vc Cutting velocity component perpendicular to the blade m/s vd Cutting velocity, drag velocity m/s vr1 Velocity of grains in the shear surface m/s vr2 Relative velocity of grains on the blade m/s vd1 Deviation velocity of grains in the shear surface m/s vd2 Deviation velocity of grains on the blade m/s vx1,2 Velocity of grains in the x-direction m/s vy1,2 Velocity of grains in the y-direction m/s vz1,2 Velocity of grains in the z-direction m/s W1 Force resulting from pore under pressure on the shear plane kN W2 Force resulting from pore under pressure on the blade kN z Water depth m α Cutting angle blade rad β Shear angle rad φ Angle of internal friction rad φ e Angle of internal friction perpendicular to the cutting edge rad δ Soil/interface friction angle rad δ e Soil/interface friction angle perpendicular to the cutting edge rad ι Deviation angle blade rad ρw Density water ton/m³
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 15. The measured SPT value reduced to the SPT value at 10m waterdepth
for water saturated sand.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 16. Specific energy and production for a 30 degree blade in clay.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 17. Specific energy and production for a 45 degree blade in clay.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 18. Specific energy and production for a 60 degree blade in clay.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 19. Specific energy and production for a 30 degree blade and a cavitating cutting process in sand as a function of the reduced SPT value.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 20. Specific energy and production for a 45 degree blade and a cavitating cutting process in sand as a function of the reduced SPT value.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Author: Dr.ir. S.A. Miedema
Figure 21. Specific energy and production for a 60 degree blade and a cavitating cutting process in sand as a function of the reduced SPT value.
Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
Copyright: Dr.ir. S.A. Miedema
Bibliography Dr.ir. S.A. Miedema 1980-2010
1. Koert, P. & Miedema, S.A., "Report on the field excursion to the USA April 1981" (PDF in Dutch 27.2 MB). Delft University of Technology, 1981, 48 pages.
2. Miedema, S.A., "The flow of dredged slurry in and out hoppers and the settlement process in hoppers" (PDF in Dutch 37 MB). ScO/81/105, Delft University of Technology, 1981, 147 pages.
3. Miedema, S.A., "The soil reaction forces on a crown cutterhead on a swell compensated ladder" (PDF in Dutch 19 MB). LaO/81/97, Delft University of Technology, 1981, 36 pages.
4. Miedema, S.A., "Computer program for the determination of the reaction forces on a cutterhead, resulting from the motions of the cutterhead" (PDF in Dutch 11 MB). Delft Hydraulics, 1981, 82 pages.
5. Miedema, S.A. "The mathematical modeling of the soil reaction forces on a cutterhead and the development of the computer program DREDMO" (PDF in Dutch 25 MB). CO/82/125, Delft University of Technology, 1982, with appendices 600 pages.
6. Miedema, S.A.,"The Interaction between Cutterhead and Soil at Sea" (In Dutch). Proc. Dredging Day November 19th, Delft University of Technology 1982.
7. Miedema, S.A., "A comparison of an underwater centrifugal pump and an ejector pump" (PDF in Dutch 3.2 MB). Delft University of Technology, 1982, 18 pages.
8. Miedema, S.A., "Computer simulation of Dredging Vessels" (In Dutch). De Ingenieur, Dec. 1983. (Kivi/Misset).
9. Koning, J. de, Miedema, S.A., & Zwartbol, A., "Soil/Cutterhead Interaction under Wave Conditions (Adobe Acrobat PDF-File 1 MB)". Proc. WODCON X, Singapore 1983.
10. Miedema, S.A. "Basic design of a swell compensated cutter suction dredge with axial and radial compensation on the cutterhead" (PDF in Dutch 20 MB). CO/82/134, Delft University of Technology, 1983, 64 pages.
11. Miedema, S.A., "Design of a seagoing cutter suction dredge with a swell compensated ladder" (PDF in Dutch 27 MB). IO/83/107, Delft University of Technology, 1983, 51 pages.
12. Miedema, S.A., "Mathematical Modeling of a Seagoing Cutter Suction Dredge" (In Dutch). Published: The Hague, 18-9-1984, KIVI Lectures, Section Under Water Technology.
13. Miedema, S.A., "The Cutting of Densely Compacted Sand under Water (Adobe Acrobat PDF-File 575 kB)". Terra et Aqua No. 28, October 1984 pp. 4-10.
14. Miedema, S.A., "Longitudinal and Transverse Swell Compensation of a Cutter Suction Dredge" (In Dutch). Proc. Dredging Day November 9th 1984, Delft University of Technology 1984.
15. Miedema, S.A., "Compensation of Velocity Variations". Patent application no. 8403418, Hydromeer B.V. Oosterhout, 1984.
16. Miedema, S.A., "Mathematical Modeling of the Cutting of Densely Compacted Sand Under Water". Dredging & Port Construction, July 1985, pp. 22-26.
17. Miedema, S.A., "Derivation of the Differential Equation for Sand Pore Pressures". Dredging & Port Construction, September 1985, pp. 35.
18. Miedema, S.A., "The Application of a Cutting Theory on a Dredging Wheel (Adobe Acrobat 4.0 PDF-File 745 kB)". Proc. WODCON XI, Brighton 1986.
19. Miedema, S.A., "Underwater Soil Cutting: a Study in Continuity". Dredging & Port Construction, June 1986, pp. 47-53.
20. Miedema, S.A., "The cutting of water saturated sand, laboratory research" (In Dutch). Delft University of Technology, 1986, 17 pages.
21. Miedema, S.A., "The forces on a trenching wheel, a feasibility study" (In Dutch). Delft, 1986, 57 pages + software.
22. Miedema, S.A., "The translation and restructuring of the computer program DREDMO from ALGOL to FORTRAN" (In Dutch). Delft Hydraulics, 1986, 150 pages + software.
23. Miedema, S.A., "Calculation of the Cutting Forces when Cutting Water Saturated Sand (Adobe Acrobat 4.0 PDF-File 16 MB)". Basic Theory and Applications for 3-D Blade Movements and Periodically Varying Velocities for, in Dredging Commonly used Excavating Means. Ph.D. Thesis, Delft University of Technology, September 15th 1987.
24. Bakker, A. & Miedema, S.A., "The Specific Energy of the Dredging Process of a Grab Dredge". Delft University of Technology, 1988, 30 pages.
25. Miedema, S.A., "On the Cutting Forces in Saturated Sand of a Seagoing Cutter Suction Dredge (Adobe Acrobat 4.0 PDF-File 1.5 MB)". Proc. WODCON XII, Orlando, Florida, USA, April 1989. This paper was given the IADC Award for the best technical paper on the subject of dredging in 1989.
26. Miedema, S.A., "The development of equipment for the determination of the wear on pick-points" (In Dutch). Delft University of Technology, 1990, 30 pages (90.3.GV.2749, BAGT 462).
27. Miedema, S.A., "Excavating Bulk Materials" (In Dutch). Syllabus PATO course, 1989 & 1991, PATO The Hague, The Netherlands.
28. Miedema, S.A., "On the Cutting Forces in Saturated Sand of a Seagoing Cutter Suction Dredge (Adobe Acrobat 4.0 PDF-File 1.5 MB)". Terra et Aqua No. 41, December 1989, Elseviers Scientific Publishers.
29. Miedema, S.A., "New Developments of Cutting Theories with respect to Dredging, the Cutting of Clay (Adobe Acrobat 4.0 PDF-File 640 kB)". Proc. WODCON XIII, Bombay, India, 1992.
30. Davids, S.W. & Koning, J. de & Miedema, S.A. & Rosenbrand, W.F., "Encapsulation: A New Method for the Disposal of Contaminated Sediment, a Feasibility Study (Adobe Acrobat 4.0 PDF-File 3MB)". Proc. WODCON XIII, Bombay, India, 1992.
31. Miedema, S.A. & Journee, J.M.J. & Schuurmans, S., "On the Motions of a Seagoing Cutter Dredge, a Study in Continuity (Adobe Acrobat 4.0 PDF-File 396 kB)". Proc. WODCON XIII, Bombay, India, 1992.
32. Becker, S. & Miedema, S.A. & Jong, P.S. de & Wittekoek, S., "On the Closing Process of Clamshell Dredges in Water Saturated Sand (Adobe Acrobat 4.0 PDF-File 1 MB)". Proc. WODCON XIII, Bombay, India, 1992. This paper was given the IADC Award for the best technical paper on the subject of dredging in 1992.
33. Becker, S. & Miedema, S.A. & Jong, P.S. de & Wittekoek, S., "The Closing Process of Clamshell Dredges in Water Saturated Sand (Adobe Acrobat 4.0 PDF-File 1 MB)". Terra et Aqua No. 49, September 1992, IADC, The Hague.
34. Miedema, S.A., "Modeling and Simulation of Dredging Processes and Systems". Symposium "Zicht op Baggerprocessen", Delft University of Technology, Delft, The Netherlands, 29 October 1992.
35. Miedema, S.A., "Dredmo User Interface, Operators Manual". Report: 92.3.GV.2995. Delft University of Technology, 1992, 77 pages.
36. Miedema, S.A., "Inleiding Mechatronica, college WBM202" Delft University of Technology, 1992.
37. Miedema, S.A. & Becker, S., "The Use of Modeling and Simulation in the Dredging Industry, in Particular the Closing Process of Clamshell Dredges", CEDA Dredging Days 1993, Amsterdam, Holland, 1993.
38. Miedema, S.A., "On the Snow-Plough Effect when Cutting Water Saturated Sand with Inclined Straight Blades (Adobe Acrobat 4.0 PDF-File 503 kB)". ASCE Proc. Dredging 94, Orlando, Florida, USA, November 1994. Additional Measurement Graphs. (Adobe Acrobat 4.0 PDF-File 209 kB).
39. Riet, E. van, Matousek, V. & Miedema, S.A., "A Reconstruction of and Sensitivity Analysis on the Wilson Model for Hydraulic Particle Transport (Adobe Acrobat 4.0 PDF-File 50 kB)". Proc. 8th Int. Conf. on Transport and Sedimentation of Solid Particles, 24-26 January 1995, Prague, Czech Republic.
40. Vlasblom, W.J. & Miedema, S.A., "A Theory for Determining Sedimentation and Overflow Losses in Hoppers (Adobe Acrobat 4.0 PDF-File 304 kB)". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995.
41. Miedema, S.A., "Production Estimation Based on Cutting Theories for Cutting Water Saturated Sand (Adobe Acrobat 4.0 PDF-File 423 kB)". Proc. WODCON IV, November 1995, Amsterdam, The Netherlands 1995. Additional Specific Energy and Production Graphs. (Adobe Acrobat 4.0 PDF-File 145 kB).
42. Riet, E.J. van, Matousek, V. & Miedema, S.A., "A Theoretical Description and Numerical Sensitivity Analysis on Wilson's Model for Hydraulic Transport in Pipelines (Adobe Acrobat 4.0 PDF-File 50 kB)". Journal of Hydrology & Hydromechanics, Slovak Ac. of Science, Bratislava, June 1996.
43. Miedema, S.A. & Vlasblom, W.J., "Theory for Hopper Sedimentation (Adobe Acrobat 4.0 PDF-File 304 kB)". 29th Annual Texas A&M Dredging Seminar. New Orleans, June 1996.
44. Miedema, S.A., "Modeling and Simulation of the Dynamic Behavior of a Pump/Pipeline System (Adobe Acrobat 4.0 PDF-File 318 kB)". 17th Annual Meeting & Technical Conference of the Western Dredging Association. New Orleans, June 1996.
45. Miedema, S.A., "Education of Mechanical Engineering, an Integral Vision". Faculty O.C.P., Delft University of Technology, 1997 (in Dutch).
46. Miedema, S.A., "Educational Policy and Implementation 1998-2003 (versions 1998, 1999 and 2000) (Adobe Acrobat 4.0 PDF_File 195 kB)". Faculty O.C.P., Delft University of Technology, 1998, 1999 and 2000 (in Dutch).
47. Keulen, H. van & Miedema, S.A. & Werff, K. van der, "Redesigning the curriculum of the first three years of the mechanical engineering curriculum". Proceedings of the International Seminar on Design in Engineering Education, SEFI-Document no.21, page 122, ISBN 2-87352-024-8, Editors: V. John & K. Lassithiotakis, Odense, 22-24 October 1998.
48. Miedema, S.A. & Klein Woud, H.K.W. & van Bemmel, N.J. & Nijveld, D., "Self Assesment Educational Programme Mechanical Engineering (Adobe Acrobat 4.0 PDF-File 400 kB)". Faculty O.C.P., Delft University of Technology, 1999.
49. Van Dijk, J.A. & Miedema, S.A. & Bout, G., "Curriculum Development Mechanical Engineering". MHO 5/CTU/DUT/Civil Engineering. Cantho University Vietnam, CICAT Delft, April 1999.
50. Miedema, S.A., "Considerations in building and using dredge simulators (Adobe Acrobat 4.0 PDF-File 296 kB)". Texas A&M 31st Annual Dredging Seminar. Louisville Kentucky, May 16-18, 1999.
51. Miedema, S.A., "Considerations on limits of dredging processes (Adobe Acrobat 4.0 PDF-File 523 kB)". 19th Annual Meeting & Technical Conference of the Western Dredging Association. Louisville Kentucky, May 16-18, 1999.
52. Miedema, S.A. & Ruijtenbeek, M.G. v.d., "Quality management in reality", "Kwaliteitszorg in de praktijk". AKO conference on quality management in education. Delft University of Technology, November 3rd 1999.
53. Miedema, S.A., "Curriculum Development Mechanical Engineering (Adobe Acrobat 4.0 PDF-File 4 MB)". MHO 5-6/CTU/DUT. Cantho University Vietnam, CICAT Delft, Mission October 1999.
54. Vlasblom, W.J., Miedema, S.A., Ni, F., "Course Development on Topic 5: Dredging Technology, Dredging Equipment and Dredging Processes". Delft University of Technology and CICAT, Delft July 2000.
55. Miedema, S.A., Vlasblom, W.J., Bian, X., "Course Development on Topic 5: Dredging Technology, Power Drives, Instrumentation and Automation". Delft University of Technology and CICAT, Delft July 2000.
56. Randall, R. & Jong, P. de & Miedema, S.A., "Experience with cutter suction dredge simulator training (Adobe Acrobat 4.0 PDF-File 1.1 MB)". Texas A&M 32nd Annual Dredging Seminar. Warwick, Rhode Island, June 25-28, 2000.
57. Miedema, S.A., "The modelling of the swing winches of a cutter dredge in relation with simulators (Adobe Acrobat 4.0 PDF-File 814 kB)". Texas A&M 32nd Annual Dredging Seminar. Warwick, Rhode Island, June 25-28, 2000.
58. Hofstra, C. & Hemmen, A. van & Miedema, S.A. & Hulsteyn, J. van, "Describing the position of backhoe dredges (Adobe Acrobat 4.0 PDF-File 257 kB)". Texas A&M 32nd Annual Dredging Seminar. Warwick, Rhode Island, June 25-28, 2000.
59. Miedema, S.A., "Automation of a Cutter Dredge, Applied to the Dynamic Behaviour of a Pump/Pipeline System (Adobe Acrobat 4.0 PDF-File 254 kB)". Proc. WODCON VI, April 2001, Kuala Lumpur, Malaysia 2001.
60. Heggeler, O.W.J. ten, Vercruysse, P.M., Miedema, S.A., "On the Motions of Suction Pipe Constructions a Dynamic Analysis (Adobe Acrobat 4.0 PDF-File 110 kB)". Proc. WODCON VI, April 2001, Kuala Lumpur, Malaysia 2001.
61. Miedema, S.A. & Zhao Yi, "An Analytical Method of Pore Pressure Calculations when Cutting Water Saturated Sand (Adobe Acrobat PDF-File 2.2 MB)". Texas A&M 33nd Annual Dredging Seminar, June 2001, Houston, USA 2001.
62. Miedema, S.A., "A Numerical Method of Calculating the Dynamic Behaviour of Hydraulic Transport (Adobe Acrobat PDF-File 246 kB)". 21st Annual Meeting & Technical Conference of the Western Dredging Association, June 2001, Houston, USA 2001.
63. Zhao Yi, & Miedema, S.A., "Finite Element Calculations To Determine The Pore Pressures When Cutting Water Saturated Sand At Large Cutting Angles (Adobe Acrobat PDF-File 4.8 MB)". CEDA Dredging Day 2001, November 2001, Amsterdam, The Netherlands.
64. Miedema, S.A., "Mission Report Cantho University". MHO5/6, Phase Two, Mission to Vietnam by Dr.ir. S.A. Miedema DUT/OCP Project Supervisor, 27 September-8 October 2001, Delft University/CICAT.
65. (Zhao Yi), & (Miedema, S.A.), "
" (Finite Element Calculations To Determine The Pore Pressures When Cutting Water
Saturated Sand At Large Cutting Angles (Adobe Acrobat PDF-File 4.8 MB))". To be published in 2002.
66. Miedema, S.A., & Riet, E.J. van, & Matousek, V., "Theoretical Description And Numerical Sensitivity Analysis On Wilson Model For Hydraulic Transport Of Solids In Pipelines (Adobe Acrobat PDF-File 147 kB)". WEDA Journal of Dredging Engineering, March 2002.
67. Miedema, S.A., & Ma, Y., "The Cutting of Water Saturated Sand at Large Cutting Angles (Adobe Acrobat PDF-File 3.6 MB)". Proc. Dredging02, May 5-8, Orlando, Florida, USA.
68. Miedema, S.A., & Lu, Z., "The Dynamic Behavior of a Diesel Engine (Adobe Acrobat PDF-File 363 kB)". Proc. WEDA XXII Technical Conference & 34th Texas A&M Dredging Seminar, June 12-15, Denver, Colorado, USA.
69. Miedema, S.A., & He, Y., "The Existance of Kinematic Wedges at Large Cutting Angles (Adobe Acrobat PDF-File 4 MB)". Proc. WEDA XXII Technical Conference & 34th Texas A&M Dredging Seminar, June 12-15, Denver, Colorado, USA.
70. Ma, Y., Vlasblom, W.J., Miedema, S.A., Matousek, V., "Measurement of Density and Velocity in Hydraulic Transport using Tomography". Dredging Days 2002, Dredging without boundaries, Casablanca, Morocco, V64-V73, 22-24 October 2002.
71. Ma, Y., Miedema, S.A., Vlasblom, W.J., "Theoretical Simulation of the Measurements Process of Electrical Impedance Tomography". Asian Simulation Conference/5th International Conference on System Simulation and Scientific Computing, Shanghai, 3-6 November 2002, p. 261-265, ISBN 7-5062-5571-5/TP.75.
72. Thanh, N.Q., & Miedema, S.A., "Automotive Electricity and Electronics". Delft University of Technology and CICAT, Delft December 2002.
73. Miedema, S.A., Willemse, H.R., "Report on MHO5/6 Mission to Vietnam". Delft University of Technology and CICAT, Delft Januari 2003.
74. Ma, Y., Miedema, S.A., Matousek, V., Vlasblom, W.J., "Tomography as a Measurement Method for Density and Velocity Distributions". 23rd WEDA Technical Conference & 35th TAMU Dredging Seminar, Chicago, USA, june 2003.
75. Miedema, S.A., Lu, Z., Matousek, V., "Numerical Simulation of a Development of a Density Wave in a Long Slurry Pipeline". 23rd WEDA Technical Conference & 35th TAMU Dredging Seminar, Chicago, USA, june 2003.
76. Miedema, S.A., Lu, Z., Matousek, V., "Numerical simulation of the development of density waves in a long pipeline and the dynamic system behavior". Terra et Aqua, No. 93, p. 11-23.
77. Miedema, S.A., Frijters, D., "The Mechanism of Kinematic Wedges at Large Cutting Angles - Velocity and Friction Measurements". 23rd WEDA Technical Conference & 35th TAMU Dredging Seminar, Chicago, USA, june 2003.
78. Tri, Nguyen Van, Miedema, S.A., Heijer, J. den, "Machine Manufacturing Technology". Lecture notes, Delft University of Technology, Cicat and Cantho University Vietnam, August 2003.
79. Miedema, S.A., "MHO5/6 Phase Two Mission Report". Report on a mission to Cantho University Vietnam October 2003. Delft University of Technology and CICAT, November 2003.
80. Zwanenburg, M., Holstein, J.D., Miedema, S.A., Vlasblom, W.J., "The Exploitation of Cockle Shells". CEDA Dredging Days 2003, Amsterdam, The Netherlands, November 2003.
81. Zhi, L., Miedema, S.A., Vlasblom, W.J., Verheul, C.H., "Modeling and Simulation of the Dynamic Behaviour of TSHD's Suction Pipe System by using Adams". CHIDA Dredging Days, Shanghai, China, november 2003.
http://www.dredgingengineering.com/dredging/media/LectureNotes/miedema/2003_dredging_days/cockle.pdf
82. Miedema, S.A., "The Existence of Kinematic Wedges at Large Cutting Angles". CHIDA Dredging Days, Shanghai, China, november 2003.
83. Miedema, S.A., Lu, Z., Matousek, V., "Numerical Simulation of the Development of Density Waves in a Long Pipeline and the Dynamic System Behaviour". Terra et Aqua 93, December 2003.
84. Miedema, S.A. & Frijters, D.D.J., "The wedge mechanism for cutting of water saturated sand at large cutting angles". WODCON XVII, September 2004, Hamburg Germany.
85. Verheul, O. & Vercruijsse, P.M. & Miedema, S.A., "The development of a concept for accurate and efficient dredging at great water depths". WODCON XVII, September 2004, Hamburg Germany.
86. Miedema, S.A., "THE CUTTING MECHANISMS OF WATER SATURATED SAND AT SMALL AND LARGE CUTTING ANGLES". International Conference on Coastal Infrastructure Development - Challenges in the 21st Century. HongKong, november 2004.
87. Ir. M. Zwanenburg , Dr. Ir. S.A. Miedema , Ir J.D. Holstein , Prof.ir. W.J.Vlasblom, "REDUCING THE DAMAGE TO THE SEA FLOOR WHEN DREDGING COCKLE SHELLS". WEDAXXIV & TAMU36, Orlando, Florida, USA, July 2004.
88. Verheul, O. & Vercruijsse, P.M. & Miedema, S.A., "A new concept for accurate and efficient dredging in deep water". Ports & Dredging, IHC, 2005, E163.
89. Miedema, S.A., "Scrapped?". Dredging & Port Construction, September 2005. 90. Miedema, S.A. & Vlasblom, W.J., " Bureaustudie Overvloeiverliezen". In opdracht
van Havenbedrijf Rotterdam, September 2005, Confidential. 91. He, J., Miedema, S.A. & Vlasblom, W.J., "FEM Analyses Of Cutting Of Anisotropic
Densely Compacted and Saturated Sand", WEDAXXV & TAMU37, New Orleans, USA, June 2005.
92. Miedema, S.A., "The Cutting of Water Saturated Sand, the FINAL Solution". WEDAXXV & TAMU37, New Orleans, USA, June 2005.
93. Miedema, S.A. & Massie, W., "Selfassesment MSc Offshore Engineering", Delft University of Technology, October 2005.
94. Miedema, S.A., "THE CUTTING OF WATER SATURATED SAND, THE SOLUTION". CEDA African Section: Dredging Days 2006 - Protection of the coastline, dredging sustainable development, Nov. 1-3, Tangiers, Morocco.
95. Miedema, S.A., "La solution de prélèvement par désagrégation du sable saturé en eau". CEDA African Section: Dredging Days 2006 - Protection of the coastline, dredging sustainable development, Nov. 1-3, Tangiers, Morocco.
96. Miedema, S.A. & Vlasblom, W.J., "THE CLOSING PROCESS OF CLAMSHELL DREDGES IN WATER-SATURATED SAND". CEDA African Section: Dredging Days 2006 - Protection of the coastline, dredging sustainable development, Nov. 1-3, Tangiers, Morocco.
97. Miedema, S.A. & Vlasblom, W.J., "Le processus de fermeture des dragues à benne preneuse en sable saturé". CEDA African Section: Dredging Days 2006 - Protection of the coastline, dredging sustainable development, Nov. 1-3, Tangiers, Morocco.
98. Miedema, S.A. "THE CUTTING OF WATER SATURATED SAND, THE SOLUTION". The 2nd China Dredging Association International Conference & Exhibition, themed 'Dredging and Sustainable Development' and in Guangzhou, China, May 17-18 2006.
99. Ma, Y, Ni, F. & Miedema, S.A., "Calculation of the Blade Cutting Force for small Cutting Angles based on MATLAB". The 2nd China Dredging Association
http://www.dredgingengineering.com/dredging/media/LectureNotes/miedema/2004_wodcon/paperfrijters.pdf
International Conference & Exhibition, themed 'Dredging and Sustainable Development' and in Guangzhou, China, May 17-18 2006.
100. ,"" (download). The 2nd China Dredging
Association International Conference & Exhibition, themed 'Dredging and Sustainable Development' and in Guangzhou, China, May 17-18 2006.
101. Miedema, S.A. , Kerkvliet, J., Strijbis, D., Jonkman, B., Hatert, M. v/d, "THE DIGGING AND HOLDING CAPACITY OF ANCHORS". WEDA XXVI AND TAMU 38, San Diego, California, June 25-28, 2006.
102. Schols, V., Klaver, Th., Pettitt, M., Ubuan, Chr., Miedema, S.A., Hemmes, K. & Vlasblom, W.J., "A FEASIBILITY STUDY ON THE APPLICATION OF FUEL CELLS IN OIL AND GAS SURFACE PRODUCTION FACILITIES". Proceedings of FUELCELL2006, The 4th International Conference on FUEL CELL SCIENCE, ENGINEERING and TECHNOLOGY, June 19-21, 2006, Irvine, CA.
103. Miedema, S.A., "Polytechnisch Zakboek 51ste druk, Hoofdstuk G: Werktuigbouwkunde", pG1-G88, Reed Business Information, ISBN-10: 90.6228.613.5, ISBN-13: 978.90.6228.613.3. Redactie: Fortuin, J.B., van Herwijnen, F., Leijendeckers, P.H.H., de Roeck, G. & Schwippert, G.A.
104. MA Ya-sheng, NI Fu-sheng, S.A. Miedema, "Mechanical Model of Water Saturated Sand Cutting at Blade Large Cutting Angles", Journal of Hohai University Changzhou, ISSN 1009-1130, CN 32-1591, 2006. 绞刀片大角度切削水饱和沙的力学模型, 马亚生[1] 倪福生[1] S.A.Miedema[2], 《河海大学常州分校学报》-2006年20卷3期 -59-61页
105. Miedema, S.A., Lager, G.H.G., Kerkvliet, J., “An Overview of Drag Embedded Anchor Holding Capacity for Dredging and Offshore Applications”. WODCON, Orlando, USA, 2007.
106. Miedema, S.A., Rhee, C. van, “A SENSITIVITY ANALYSIS ON THE EFFECTS OF DIMENSIONS AND GEOMETRY OF TRAILING SUCTION HOPPER DREDGES”. WODCON ORLANDO, USA, 2007.
107. Miedema, S.A., Bookreview: Useless arithmetic, why environmental scientists can't predict the future, by Orrin H. Pilkey & Linda Pilkey-Jarvis. Terra et Aqua 108, September 2007, IADC, The Hague, Netherlands.
108. Miedema, S.A., Bookreview: The rock manual: The use of rock in hydraulic engineering, by CIRIA, CUR, CETMEF. Terra et Aqua 110, March 2008, IADC, The Hague, Netherlands.
109. Miedema, S.A., "An Analytical Method To Determine Scour". WEDA XXVIII & Texas A&M 39. St. Louis, USA, June 8-11, 2008.
110. Miedema, S.A., "A Sensitivity Analysis Of The Production Of Clamshells". WEDA XXVIII & Texas A&M 39. St. Louis, USA, June 8-11, 2008.
111. Miedema, S.A., "An Analytical Approach To The Sedimentation Process In Trailing Suction Hopper Dredgers". Terra et Aqua 112, September 2008, IADC, The Hague, Netherlands.
112. Hofstra, C.F., & Rhee, C. van, & Miedema, S.A. & Talmon, A.M., "On The Particle Trajectories In Dredge Pump Impellers". 14th International Conference Transport & Sedimentation Of Solid Particles. June 23-27 2008, St. Petersburg, Russia.
113. Miedema, S.A., "A Sensitivity Analysis Of The Production Of Clamshells". WEDA Journal of Dredging Engineering, December 2008.
114. Miedema, S.A., "New Developments Of Cutting Theories With Respect To Dredging, The Cutting Of Clay And Rock". WEDA XXIX & Texas A&M 40. Phoenix Arizona, USA, June 14-17 2009.
115. Miedema, S.A., "A Sensitivity Analysis Of The Scaling Of TSHD's". WEDA XXIX & Texas A&M 40. Phoenix Arizona, USA, June 14-17 2009.
116. Liu, Z., Ni, F., Miedema, S.A., “Optimized design method for TSHD’s swell compensator, basing on modelling and simulation”. International Conference on Industrial Mechatronics and Automation, pp. 48-52. Chengdu, China, May 15-16, 2009.
117. Miedema, S.A., "The effect of the bed rise velocity on the sedimentation process in hopper dredges". Journal of Dredging Engineering, Vol. 10, No. 1 , 10-31, 2009.
118. Miedema, S.A., “New developments of cutting theories with respect to offshore applications, the cutting of sand, clay and rock”. ISOPE 2010, Beijing China, June 2010.
119. Miedema, S.A., “The influence of the strain rate on cutting processes”. ISOPE 2010, Beijing China, June 2010.
120. Ramsdell, R.C., Miedema, S.A., “Hydraulic transport of sand/shell mixtures”. WODCON XIX, Beijing China, September 2010.
121. Abdeli, M., Miedema, S.A., Schott, D., Alvarez Grima, M., “The application of discrete element modeling in dredging”. WODCON XIX, Beijing China, September 2010.
122. Hofstra, C.F., Miedema, S.A., Rhee, C. van, “Particle trajectories near impeller blades in centrifugal pumps. WODCON XIX, Beijing China, September 2010.
123. Miedema, S.A., “Constructing the Shields curve, a new theoretical approach and its applications”. WODCON XIX, Beijing China, September 2010.
124. Miedema, S.A., “The effect of the bed rise velocity on the sedimentation process in hopper dredges”. WODCON XIX, Beijing China, September 2010.
![[PEGASUS]² Aims, Rules and Procedures 25 September 2015 Dr.ir. Isabelle Verbaeys.](https://static.fdocuments.net/doc/165x107/56649ebc5503460f94bc5bc2/pegasus-aims-rules-and-procedures-25-september-2015-drir-isabelle-verbaeys.jpg)
