Process Dynamic Simulation using Aspen HYSYS V 8.6...
Transcript of Process Dynamic Simulation using Aspen HYSYS V 8.6...
![Page 1: Process Dynamic Simulation using Aspen HYSYS V 8.6 “Advanced”boostuae.co/wp-content/uploads/2017/09/Process-Dynamic... · 2017-09-20 · PROCESS DYNAMIC SIMULATION USING ASPEN](https://reader030.fdocuments.net/reader030/viewer/2022012313/5e250342c26e09190657277c/html5/thumbnails/1.jpg)
PROCESS DYNAMIC SIMULATION USING ASPEN HYSYS V 8.6 “ADVANCED”
SECTOR / INFORMATION TECHNOLOGY TECHNICAL & CERTIFIED TRAINING COURSE
Develop the knowledge and understanding of using computer based simulation.
www.Boostuae.com Tel: +971-24496000 Fax: +971-24496777 Email: [email protected]
PROCESS DYNAMIC SIMULATION USING ASPEN HYSYS V 8.6 “ADVANCED”
SECTOR / INFORMATION TECHNOLOGY TECHNICAL & CERTIFIED TRAINING COURSE
![Page 2: Process Dynamic Simulation using Aspen HYSYS V 8.6 “Advanced”boostuae.co/wp-content/uploads/2017/09/Process-Dynamic... · 2017-09-20 · PROCESS DYNAMIC SIMULATION USING ASPEN](https://reader030.fdocuments.net/reader030/viewer/2022012313/5e250342c26e09190657277c/html5/thumbnails/2.jpg)
PROC
ESS D
YNAM
IC SI
MUL
ATIO
N US
ING A
SPEN
HYS
YS V
8.6 “A
DVAN
CED”
www.Boostuae.com Tel: +971-24496000 Fax: +971-24496777 [email protected]
THE COURSE AIMS TO:
✓ Develop the knowledge and understanding of using computer based simulation.
✓ Introduce Aspen HYSYS as Dynamic simulation software and its outcomes.
✓ Develop the competences in using HYSYS Dynamics.
✓ Develop the competences in developing, planning and implementation of trials and changing plant operating conditions and control system using HYSYS dynamic simulation.
✓ Support engineers to use HYSYS Dynamics to monitor control systems and system disturbances.
✓ Develop the competences in sizing equipment and evaluating performance.
![Page 3: Process Dynamic Simulation using Aspen HYSYS V 8.6 “Advanced”boostuae.co/wp-content/uploads/2017/09/Process-Dynamic... · 2017-09-20 · PROCESS DYNAMIC SIMULATION USING ASPEN](https://reader030.fdocuments.net/reader030/viewer/2022012313/5e250342c26e09190657277c/html5/thumbnails/3.jpg)
COURSE CONTENT
DAY ONE ✓ Introduction to Aspen HYSYS ✓ Refreshment of HYSYS Basics ✓ Build Steady state model which will be
used in Dynamic simulation
DAY TWO ✓ Transitional to Dynamic model ✓ Dynamic Theory ✓ Equipment Sizing ✓ Controllers theory
DAY THREE ✓ Controllers’ configuration, pressure
flow theory. ✓ Strip charts and event scheduler
This agenda is being provided to you as a guideline and is subject to change based on attendees and instructor recommendations during the course.
PROC
ESS D
YNAM
IC SI
MUL
ATIO
N US
ING A
SPEN
HYS
YS V
8.6 “A
DVAN
CED”
www.Boostuae.com Tel: +971-24496000 Fax: +971-24496777 [email protected]
DAY FOUR ✓ Column Dynamics and relief valves ✓ Centrifugal Compressor surge
DAY FIVE ✓ Shutdowns and Startups ✓ Open discussion
![Page 4: Process Dynamic Simulation using Aspen HYSYS V 8.6 “Advanced”boostuae.co/wp-content/uploads/2017/09/Process-Dynamic... · 2017-09-20 · PROCESS DYNAMIC SIMULATION USING ASPEN](https://reader030.fdocuments.net/reader030/viewer/2022012313/5e250342c26e09190657277c/html5/thumbnails/4.jpg)
THANK YOU
BOOSTUAE.COM
PROCESS DYNAMIC SIMULATION USING ASPEN HYSYS V 8.6 “ADVANCED”
SECTOR / INFORMATION TECHNOLOGY TECHNICAL & CERTIFIED TRAINING COURSE