PRICE BID/BOQengineeringprojects.com/Tender/UploadFiles/4699_VOLUME... · 2019-03-22 · 660.01...
Transcript of PRICE BID/BOQengineeringprojects.com/Tender/UploadFiles/4699_VOLUME... · 2019-03-22 · 660.01...
AN ISO 9001 & 14001 COMPANY
TENDER DOCUMENT
TENDER No: WRO/CON/029-B/0218
Electrical Work for Teaching Hospital
for the new Govt. Medical college at
Baripada, Odisha
VOLUME – III
PRICE BID/BOQ
Total Amount( Rs.)
1 2 3 4 5= (3 x 4 ) 3 + 5
In figures In words In figures In words
2 Electrical Work 135137290.26
Total 135137290.26
Note:
1. Rates to be quoted in this tender all inclusive with all taxes and duties etc. Excluding GST.
2.The bidder has to quote above/below percentage (%) Excluding GST However, the percentage (%) of GST applicable is to be shown separately
for reference
BIDDERS FINANCIAL OFFER:
(In Figures)__________________________________________________________________________________________________
(In Words)___________________________________________________________________________________________________
Tender for “Electrical Work for Teaching Hospital for the new Govt. Medical College at Baripada, Odisha”
WRO/CON/B-04/030-C
PRICE SCHEDULE
SI. No. DESCRIPTION ESTIMATED COST (Rs.)TO BE QUOTED BY TENDERER
% ( - ) Below / At Par/Above Amount In INR
Signature of EPIL Signature of Bidder
Sl.
No.
Item Description Quantity Units Estimated Rate
(excluding GST)
TOTAL AMOUNT (excluding
GST)1 2 3 4 5 6
HVAC WORK
501 HVAC WORK
Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 11 KV grade of following
size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc
as required.
501.01 Laying of MV XLPE Cable upto 35 sq. mm in ground 2362.00 Mtr 217.00 512554
501.02 Above 35 sq. mm and upto 95 sq. mm in ground 1.00 Mtr 223.00 223
501.03 Laying of Above 95 sq. mm and upto 185 sq. mm XLPE power cable of 1.1 kV grade direct in ground 40.00 Mtr 229.00 9160
501.04 Laying of Above 185 sq. mm and upto 400 sq. mm XLPE power cable of 1.1 kV grade direct in ground 240.00 Mtr 247.00 59280
502 1.1 kV L.T CONTROL CABLE LAYING
1.1 kV L.T Cable Laying of one number armoured XLPE insulated and PVC sheathed control cable 1.1 kV
of following size in the existing cable Trays/ Surface including providing suitable size clamp to secure the
cable in tray/ surface as required.
502.01 4 core, 7 core, 2.5 Sq.mm. Cu. Conductor cable 800.00 Metre 32.00 25600
503 Supplying and making end termination with brass compression gland and aluminium lugs for following size
of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
503.01 3.5 core, 240 Sq.mm.-Alumiium Cable 12.00 Sets 458.00 5496
503.02 3.5 core, 150 Sq.mm.-Alumiium Cable 4.00 Sets 596.00 2384
503.03 3 core, 35 Sq.mm.-Alumiium Cable 1.00 Sets 167.00 167
503.04 3 core, 25 Sq.mm.-Alumiium Cable 8.00 Sets 143.00 1144
503.05 3 core, 16 Sq.mm.-Alumiium Cable 1.00 Sets 142.00 142
503.06 3 core, 10 Sq.mm.-Copper Cable 20.00 Sets 122.00 2440
503.07 3 core, 6 Sq.mm.-Copper Cable 94.00 Sets 101.00 9494
503.08 3 core, 4 Sq.mm. -Copper Cable 206.00 Sets 101.00 20806
504 EARTHING
504.01 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required. 800.00 Metre 249.00 199200
504.02 Providing and fixing 6 SWG dia G.I. wire on surface or in recess 250.00 Metre 23.00 5750
ELECTRICAL Work
Signature of EPIL Signature of Bidder
654 E. I. WORKSupplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on
surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections,
powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)
654.01 6.00 Each 840.00 5040
654.02 8 way, Double door 13.00 Each 1451.00 18863
654.03 12 way, Double door 30.00 Each 1697.00 50910
655 Supplying and fixing following way, horizontal type threSupplying and fixing following way, horizontal type
three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with
tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including
earthing etc. as required. (But without MCB/RCCB/ Isolator)
655.01 4 way (4 + 12), Double door 1.00 Each 1962.00 1962
655.02 6 way (4 + 18), Double door 18.00 Each 2271.00 40878
655.03 8 way (4 + 24), Double door 66.00 Each 3099.00 204534
655.04 12 way (4 + 36), Double door 4.00 Each 2444.00 9776
656 Supplying and fixing 5 amps to 32 amps rating, 240 volts, 'C' series, miniature circuit breaker suitable for
inductive load of following poles in the existing MCB DB complete with connections, testing and
commissioning etc. as required.
656.01 Single pole 3284.00 Each 409.00 1343156
656.02 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. 961.00 Each 14.00 13454
657 Supplying and fixing following rating, double pole, 240 volts, isolator in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
657.01 40 amps 54.00 Each 247.00 13338
657.02 63 amps 322.00 Each 298.00 95956
658 Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
658.01 40 amps 18.00 Each 534.00 9612
658.02 63 amps 99.00 Each 556.00 55044
659 Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit
breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections,
testing and commissioning etc. as required.
659.01 40 amps 54.00 Each 1713.00 92502
659.02 63 amps 322.00 Each 1977.00 636594
660 HT AND LT CABLES
Laying of one number XLPE power cable of 33 kV grade of following size direct in ground including
excavation, sand cushioning, protective covering and refilling the trench etc. as required.
Signature of EPIL Signature of Bidder
660.01 Above 120sqmm and upto 400 Sq.mm. 230.00 M 518.00 119140
661 1.1 kV L.T Cable Laying of one number armoured XLPE insulated and PVC sheathed control cable 1.1 kV
of following size in the existing cable Trays/ Surface including providing suitable size clamp to secure the
cable in tray/ surface as required.
661.01 4 core, 7 core, 12 core & 19 core, 2.5 Sq.mm. Cu. Conductor cable 3395.00 M 217.00 736715
661.02 Above 35 sq. mm and upto 95 sq. mm in ground 2273.00 Mtr 223.00 506879
661.03 Laying of Above 95 sq. mm and upto 185 sq. mm XLPE power cable of 1.1 kV grade direct in ground 2878.00 Mtr 229.00 659062
661.04 Laying of Above 185 sq. mm and upto 400 sq. mm XLPE power cable of 1.1 kV grade direct in ground 8335.00 Mtr 247.00 2058745
662 Laying and fixing of following sizes of one number PVC insulated and PVC sheathed/XLPE Power cable
of 1.1kv grade on cable tray as required.
662.01 Upto 35 sq. mm (clamped with 1mm thick saddle) 8000.00 Mtr 32.00 256000
662.02 Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm
MS flat clamp)
622.00 Mtr 80.00 49760
662.03 Laying of MV XLPE Cable 95 sq. mm to 185 sq. mm on cable tray 8000.00 Mtr 95.00 760000
662.04 Laying of MV XLPE Cable 185 sq. mm to 400 sq. mm on cable tray 622.00 Mtr 132.00 82104
663 Supplying and making end termination with brass compression gland and aluminium lugs for following size
of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.
663.01 3.5core, 300 Sq.mm. 16.00 Sets 500.00 8000
663.02 3.5core, 240 Sq.mm. 20.00 Sets 458.00 9160
663.03 3.5 core, 185 Sq.mm. 10.00 Sets 387.00 3870
663.04 3.5 core, 150 Sq.mm. 8.00 Sets 596.00 4768
663.05 3.5 core, 120 Sq.mm. 16.00 Sets 185.00 2960
663.06 3.5 core, 95 Sq.mm. 6.00 Sets 236.00 1416
663.07 3.5 core, 70 Sq.mm. 52.00 Sets 203.00 10556
663.08 3.5 core, 50 Sq.mm. 10.00 Sets 167.00 1670
663.09 4 core, 35 Sq.mm. 14.00 Sets 167.00 2338
663.1 4 core, 25 Sq.mm. 26.00 Sets 145.00 3770
663.11 3 core, 25 Sq.mm. 4.00 Sets 143.00 572
663.12 4 core, 16 Sq.mm. 200.00 Sets 142.00 28400
663.13 3 core, 16 Sq.mm. 20.00 Sets 140.00 2800
663.14 4 core, 10 Sq.mm. 1100.00 Sets 128.00 140800
663.15 3 core, 10 Sq.mm. 60.00 Sets 122.00 7320
664 Supplying and making end termination with double brass compression gland and Copper lugs for following
size of PVC sheathed copper conducter armoured control cable of 1.1 kV grand as required.
664.01 4 core, 6 Sq.mm. 52.00 Sets 102.00 5304
Signature of EPIL Signature of Bidder
664.02 3 core, 6 Sq.mm. 46.00 Sets 101.00 4646
665 EARTHING
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry
enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt
as required.
47.00 Set 3291.00 154677
666 Earthing with GI earth plate 600mm x 600mm x 6.0mm thick including accessories and providing masonary
enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal and
salt) complete as required.
52.00 Set 2931.00 152412
667 Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing
masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc.
with charcoal/ coke and salt as required.
65.00 Set 4947.00 321555
668 Supplying and laying 6 SWG G.I. wire at 0.50 metre below ground level for conductor earth electrode,
including connection/ termination with GI thimble etc. as required.
8.00 KG 22.00 176
669 Supplying and laying 6 SWG G.I. wire tie with cable as required. 6000.00 RM 23.00 138000
670 Supplying and laying Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections
etc. as required.
2700.00 RM 249.00 672300
671 Supplying and laying Providing and fixing 50 mm X 6 mm G.I. strip on surface or in recess for connections
etc. as required.
1200.00 RM 311.00 373200
672 Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode,
including connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done
by overlapping and with 2 Set of G.I. nut bolt & spring washer spaced at 50mm)
40.00 RM 77.00 3080
673 LIGHTNING ARRESTOR
Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single
prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required
35.00 Each 250.00 8750
674 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor
complete as required.(For horizontal run)
950.00 Meter 51.00 48450
675 Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or on surface of wall for lightning conductor
complete as required. (For vertical run)
925.00 Meter 79.00 73075
676 Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 Nos. of G.I.
bolts, nuts, chuck nuts and spring washers etc. complete as required.
35.00 Each 55.00 1925
677 Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. 725.00 Meter 97.00 70325
Signature of EPIL Signature of Bidder
678 INTERNAL WIRING:
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated
copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core
cable etc. as required.
Group C
2335.00 Point 730.00 1704550
679 Wiring for light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface /
recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5
sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.
Primary point cntrld by SP MCB
34.00 Point 756.00 25704
680 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without
independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in
surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper
conductor single core cable etc. as required.
Group C
3487.00 Point 1306.00 4554022
681 Wiring for group controlled (looped) light point with 1.5 sq. mm FRLS PVC insulated copper conductor
single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC
insulated copper conductor single core cable etc. as required.
Secondary point cntrld by SP MCB
182.00 Point 1299.00 236418
682 Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in
surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single
core cable for loop earthing as required.
220.00 meter 140.00 30800
683 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated
copper conductor, single core cable in surface/ recessed steel conduit as required.
683.01 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire 21500.00 meter 107.00 2300500
683.02 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire 11049.50 meter 125.00 1381187.5
683.03 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 8527.50 meter 158.00 1347345
683.04 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 1045.00 meter 212.00 221540
684 Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including
painting in case of surface conduit, or cutting the wall and making good the same in case of recessed
conduit as required.
684.01 20 mm 11000.00 meter 86.00 946000
684.02 25 mm 56512.00 meter 94.00 5312128
684.03 32 mm 3537.00 meter 121.00 427977
685 Supplying and fixing of following sizes of medium class PVC conduit along with accessories in
surface/recess including cutting the wall and making good the same in case of recessed conduit as
required.
685.01 20 mm 4631.00 meter 42.00 194502
685.02 25 mm 39215.00 meter 47.00 1843105
685.03 32 mm 408.00 meter 61.00 24888
686 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,
including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc.
as required.
964.00 Each 320.00 308480
Signature of EPIL Signature of Bidder
686.01 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,
including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular switch,
connections etc. as required. (For light plugs to be used in non residential buildings).
877.00 Each 548.00 480596
686.02 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,
including providng and fixing 3 Nos. 3 pin 5/6 A modular socket outlet and 3 Nos. 5/ 6 A modular switch,
connections etc. as required. (For light plugs to be used in non residential buildings).
58.00 Each 870.00 50460
686.03 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,
including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch,
connections etc. as required.
904.00 Each 519.00 469176
686.04 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,
including providing and fixing 2 No.6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular
switch, connections etc. as required.
58.00 Each 844.00 48952
686.05 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess,
including providing and fixing 3 No.6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular
switch, connections etc. as required.
58.00 Each 1236.00 71688
686.06 Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess
including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, “C” curve including
connections, painting etc. as required.
110.00 Each 383.00 42130
686.07 Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including
connections etc. as required.
79.00 Each 35.00 2765
687 LIGHTING FIXTURES
Supplying and fixing brass batten/ angle holder including connections etc. as required.
2.00 Each 167.00 334
688 Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length
(upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including
providing and fixing phenolic laminated sheet cover on the fan box etc. as required.
984.00 Each 207.00 203688
689 Installation of exhaust fan in the existing opening, including making good the damage, connection, testing,
commissioning etc. as required.
79.00 Each 256.00 20224
690 Installation, testing and commissioning of Recessed Down Light/Surface Down Light /wall Mounted LED
fittings of all sizes upto 25W LED, complete with all accessories including connections etc. as required.
6050.00 Each 105.00 635250
Signature of EPIL Signature of Bidder
691 Installation, testing and commissioning of Recessed Down Light/Surface Down Light fittings of all sizes
above 25W and Upto 40W LED, complete with all accessories including connections etc. as required.
6550.00 Each 196.00 1283800
692 Installation, testing and commissioning of pre-wired, LED Tube Light fitting of all types, complete with all
accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC
insulated, copper conductor, single core cable and earthing etc. as required.
319.00 Each 98.00 31262
693 MATV,DATA & VOICE SYSTEM SYSTEM
Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated,
shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed
steel/ PVC conduit as required.
1650.00 meter 21.00 34650
694 Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including
connections etc. as required.
694.01 Telephone socket outlet 558.00 Each 77.00 42966
694.02 TV antenna socket outlet 33.00 Each 83.00 2739
694.03 Data socket outlet 947.00 Each 525.00 497175
695 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular
switches in recess etc. as required.
695.01 1 or 2 Module (75 mmX75 mm) 1535.60 Each 192.00 294835.2
696 Supplying and drawing of UTP 4 pair CAT 6 LAN Cable as per EIA in the existing surface/ recessed
Steel/PVC Conduit as required.
696.01 1 run of cable 49578.00 meter 89.00 4412442
696.02 2 run of cable 7500.00 meter 113.00 847500
696.03 3 run of cable 4500.00 meter 136.00 612000
697 33kV METERING SYSTEM AND HT PANEL
697.01 Supply, Installation, Testing and Commissioning of support for overhead line 152mmx152mm and 13 meter
long C pole of I.S. standard including base plate, welding, drilling of required hole etc. complete as
required. R.S.J pole standard weight 37.10 kg/per metre. Cost also include the foundation RCC material
of 1:6:8 ratio inclusing digging and backfilling complete as required.
4.00 Set 24581.00 98324
698 Supply, Installation, Testing and Commissioning of stranded ACSR "DOG" Conductor Size : 6/4.72+7/1.57
mm Steel Reinforced (ACSR) confirming to IS:398-1976 ofapproved make, stringing, making off complete
with binding at existing insulator, jointing, jumpering, tearing off, connecting etc. as required and clearing of
obstacles (ifany) etc.
0.02 Km. 48070.00 961.4
699 Supplying, Installation Testing and commissioning of 33kV Polymer Disc insulator (70KN) 6.00 No. 649.00 3894
699.01 Supplying, Installation Testing and commissioning of 33kV Polymer Pint insulator (70KN) 6.00 No. 749.00 4494
Signature of EPIL Signature of Bidder
699.02 Supply, Installation, Testing and Commissioning of 33kV,10kA , 1-ph, Outdoor, Gapless/Lightning/Surge
Arrester complete with insulating base,Terminal connectors etc complete for installation,Testing &
commissioning.
3.00 No. 30488.00 91464
700 Supply, Installation, Testing and Commissioning of 33kV 400A 3-Ph Gang Switch (Rocking type Air Break
Isolator) along with support insulators operating mechanism base channel down pipe terminal connector
and other acesseries complete as per IS :9921 (Pt. I to IV)or its latest ammendment and TS Vol II.
1.00 Set 69473.00 69473
701 Supply, Installation, Testing and Commissioning of 33kV Drop out fuse rated current 100A/200A/400A,
complete with fuse carrier assembly,fuse base & Tube and mounted arrangment as per IS :9385 (Pt. I to
III) or as ammended from time to time and Tech sepc. VoI-II .
1.00 Set 30832.00 30832
702 Supply, Installation, Testing and Commissioning of MS Channel 100x50x6mm. 200.00 kg 151.00 30200
703 Supply, Installation, Testing and Commissioning of MS angle 50x50x6 -4kg per meter 100.00 kg 125.00 12500
704 Supply, Installation, Testing and Commissioning of Outdoor Type Metering Cubical for 33kV Mains
Supply
1.00 Set 15676.00 15676
705 Supply, Installation, Testing and Commissioning of 33kV/110V CVT (CT& PT for metering)combind set
100A-50-25/1A for HT metering
1.00 Set 75857.00 75857
706 33kV HT PANELS
Supply, Installation, Testing and Commissioning of indoor type floor mounted metal clad, 33 kV, 1250A
VCB Panel with totally enclosed,expendable & electrically interlocked, horizontal drawout, horizontal
isolation type breaker as per IS 13118, as per specifications, having capacities as mentioned below, single
break, trip free mechanism, manually charged and closing breaker suitable for use on 33kV, 3Phase, 50Hz
A.C. supply with short circuit fault level of 750 MVA, complete with self contained electrically interlocked
rack in and rack out mechanism, air insulated & encapsulated copper bus bars of 800Amp capacity,
breaker featured with mechanical ON/ OFF indicator with hand trip device, spring release coil, shunt trip
coil and auxiliary switch of 4NO + 4NC and equipped with following switchgears and accessories i/c
connections suitable for 2No.3Cx 400*sq.mm and Outgoing shall be suitable for 3Cx 300*sq.mmas
mention in SLD. XLPE 33kV cable (cable entry from bottom, end termination with heat shr, 35 kA for 1
sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 N
Signature of EPIL Signature of Bidder
706.01 INCOMER - consisting of followings-
1250 Amp. TP VCB with earth switch.
1 No. 33kV/110Volts PT Class 0.5 accuracy and 200VA burden with 1 No. VA F (0-36 kV), digital type,
and protection HRC fuse for HT metering upto 15kV on incomer.
1 No. 33kV/240Volts PT Class 0.5 accuracy and 200VA burden for incomming supply.
1 No. Microprocessor based numerical relay with O/L, E/F and highset S/C protection compatible.
Breaker control switch
240 V AC spring charging motor.
Set of ON/OFF/TRIP indicating lamps.
Clear lamp for Trip Circuit healthy supply.
Aux. relays for Anti Pumping & indication.
Trip Circuit spervision relay.
Master Trip Circuit Relay.
Digital electronic Trivector meter with RS 485 port.
Dual core dual ratio 3 CTs 50/ 100/5A of 15VA burden and accuracy Class -0.5 for metering and class
5P10 for protection.
BUSBAR
1500 Amp aluminium Bus Bar.
OUTGOING -
4 set of Outgoing each consisting of following -
1250 Amp. VCB with earth switch.
Microprocessor based numerical relay with O/L, E/F and highset S/C prote 6A MCB.
Bus Bars
250 Amps TPN, 35 kA fo
706.02 240 V AC spring charging motor
Set of ON/OFF/TRIP indicating lamps.
Clear lamp for Trip Circuit healthy supply.
Aux. relays for Anti Pumping,Fault & indication.
Trip Circuit spervision relay.
Master Trip Circuit Relay
Individual alarm annunciator with 8 windows and buzzer, ACK, rest, test push button for individual
transformer faults and electrical faults in respective window.
Dual core dual ratio 3 CTs 20/ 40/5A of 15VA burden and accuracy Class -0.5 for metering and class 5P10
for protection.
1.00 No. 3008969.00 3008969
707 Supply, Installation, Testing and Commissioning of earth truck for 33kV VCB panel 1.00 No. 91510.00 91510
708 TRANSFORMERS
33/ 0.433 KV INDOOR TYPE TRANSFORMER
(Oil Filled TYPE WITH ON LOAD TAP CHANGE OVER)
Supply, Installation, Testing and Commissioning of 1000 KVA 3 phase, 33 / 0.433 KV Out door type oil
filled type transformer copper wound with DNY II connection and neutral brought out for earthing. The
transformer shall be provided with (+) 5% and (-) 15% in step of 1.25% ON load tap changer on HT side
confirming to IS : 1180 - 2014 and ECBC-2017. HT side cable termination box shall be suitable for 33 KV,
3 C x240mm2 XLPE cable and LT side cable terminal box shall be suitable for terminating of 2500 A
cables. The transformer shall be supplied with all accessories complete as per specifications on all
respect.
3.00 No. 1522889.00 4568667
Signature of EPIL Signature of Bidder
709 BATTERY CHARGER & BATTERIES
Supply, Installation, Testing and Commissioning of 24 V Battery Charger Capacity following capacity
batteries Battery Charger shall be solid state, full wave fully controlled bridge, input suitable for single
phase 230V AC suppply, conforming to degree of protection IP-42, Sheet steel enclosure 14 SWG thick,
with automatic voltage regulation, current limiting circuitary, auto cut facility, smooth filter circuit switches,
Ammeter & voltmeter on DC side, RYB indicating lamps (LED type) on AC side complete in all respect with
float and boost/ buck charging, switchgear, earthing, powder coated painting etc as required.Suitable for
230 V, including DC DB single phase +/- 10% AC, 50 Hz supply as per specifications
709.01 180 AH 1.00 No. 65196.00 65196
709.02 65 AH 1.00 No. 39639.00 39639
710 SAFETY EQUIPMENTS
Supplying of Rubber hand gloves suitable for 33 kV.
1.00 Pair 1148.00 1148
711 Supplying and fixing of Shock treatment chart both in Regional, Hindi & English.and framed with 5mm thick
glass as required.
5.00 Each 3651.00 18255
712 Supply & fixing HT danger notice plate of 250 mm x 200mm, made of mild steel sheet of at least 2mm thick
& vitreous enamelled white on both sides and with inscription in signal red colour on front side as required.
(33 kV)
5.00 Each 334.00 1670
713 Supply & fixing MV danger notice plate of 200 mm x 150mm, made of mild steel sheet of at least 2mm
thick & vitreous enamelled white on both sides and with inscription in signal red colour on front side as
required.
5.00 Each 240.00 1200
714 Supply of First aid box containing material as prescribed by St. John Ambulance brigade or Indian Red
Cross complete as required
1.00 Each 2921.00 2921
715 Providing of Insulatiing mat 1 meter wide & 25mm thick to withstand 36kV dielectric strength as per IS
5424- 1969
10.00 RM 2306.00 23060
716 Providing of insulating mat 1 meter wide & 6mm thick to withstand 3.3kV dielectric strength as per IS 5424-
1969
100.00 RM 1071.00 107100
717 Providing Single Line Diagram on 5mm thick Aluminium sheet in A0 Size duly laminated. 1.00 Each 2608.00 2608
718 Providing Single Line Diagram on 5mm thick Aluminium sheet in A1 Size duly laminated. 1.00 Each 2416.00 2416
Signature of EPIL Signature of Bidder
719 LT PANELS
AUTO LOAD SHARING / SYNCHRONISING PANEL FOR HOSPITAL
Supply, Installation, Testing and Commissioning of Auto Load Sharing / Synhronising Cum LT change
Over Panel cubicle type, made out of 14 swg CRCA sheet steel, totally enclosed, IP 42, protection free
standing, floor mounting, dust and vermin proof,indoor, compartmentalised, powder coated painting
suitable for operation on 3 Phase and neutral, 415v, 50 Hz AC supply system with busbars extensible on
both sides, interconnections with 2.5mm2 size of FRLS copper wire, control circuit with breaker control
switch & auto/ manual selector switch, spring charging indication, ammeter, ammeter selector switches
voltmeter, voltmeter selector switches, indicating lamps CT's, multifunction meters internally wired,
interlocking and having following incomer & Bus coupler Air circuit breakers and outgoing Air circuit
breaker/ Moulded case circuit breaker complete with releases for protection all as shown on drawing
including supply & installation complete as requi 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described as aboveSDB-3.1,3.3,3.4_ described as aboveON', 'OFF', 'TRIP' & spring charged
lamps with2 Amp control MCB.
Outgoing
719.01 Each Incomer shall have one set of the following items:
Intelligent multi function digital meter with Capability of Disturbance Direction Detection, Sag & Swell
Monitoring with Waveform Capturing, Class of accuracy: 0.2S as per IEC62053-22, Sampling Rate of 256
Samples/Cycle, Harmonics analysis upto 63rd order for Voltage & Current, RS485 PORT & Dual Ethernet
PORT.
1 Set of Indication Lamps, LED type, R,Y,B with 2 Amp control MCB and breaker 'ON', 'OFF', 'TRIP' &
spring charged lamps.
Breaker failure protection.
BUS BARS
3000 Amps TPN, 80 kA for 1 sec. Aluminiun bus bars with heat coloured shrinkable insulation sleeve. - 1
Set
BUS COUPLER
1 Set of ACB, 1600 Amps, 80kA, 4 Pole, (EDO) without release with Electrical interlocking arrangement
with incomer breakers as per single line diagram, Motor wound spring charged closing mechanism,
horizontal Drawout type including Auxilary contactor & control MCB's. if any.
OUTGOING
4 No. ACB, 1600 Amps, 100kA, 4 Pole with microprocessor release Motor wound spring charged , 35 kA
for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kw
Signature of EPIL Signature of Bidder
719.02 6 Set each outgoing Indication Lamps, LED type, for RYB with 2 Amp control MCB& breaker 'ON', 'OFF',
'TRIP' lamps with 2 Amp control MCB.
6 Set LED Indication lamps, Push buttons, window annunciation fascia etc of required quantity as per
technical specifications.
Provision shall be made for connection for control cables.
FOR MANUAL SYNCHRONIZING OPERATION (For Each DG set)
1 No - Double voltmeter analog type 0 - 500V
1 No - Double frequency meter analog type 45-55Hz
1 No - SynchroNocope analog type
1 No - Synchroning switch
1 No - Auto / Manual switch rotary
1 No - DG selectors switch (1 to 5) position
1 No - Check Synchronizing Relay
1 No. - Bright Lamp
1 No. - Dark Lamp
Control & Relay Panels for 3No. x 750 kVA DG Set
5set : Each DG Set comprising of the following :
Digital KWH Meter -
Digital KW Meter
Digital Power Factor Meter
Digital VAF Meter
Temperature Scanner
719.03 1 No: Generator Protection Relay, microprocessor Based with MODBUS/Backnet RS485 Port as per
following protection
Voltage Restrained over current & earth Fault Protection (51V/51N)
Current unbalance - 46
Loss of Excitation - 40
Reverse Power - 32
Under Power - 37
Under / Over Voltage - 27/59
Under / Over Frequency - 81
Thermal overload Protection - 49
Breaker failure Protection
High Speed Master Trip Relay - VAJH 13
Trip Circuit Supervision Relay
Numeric generator differential Bias % with dual adjustable slop with PS class CT’s on both side of
alternator.
Emergency Stop Push Button
Annunciator, 16 window with in Accept, Reset, Test & Mute
Hooter
Motorised Potentiometer for speed control
Motorised Potentiometer for voltage control
Battery Charger 24V / 25Amps
DG Selector Switch for ON/Off
DG Selector Switch for Auto/Manual/Test
Signature of EPIL Signature of Bidder
719.04 1 set Aux. Contactor, 110VAC
1 Set Aux. Contactor, 24VDC
1 No: 16A, full wave Rectifier, 24V DC
1 No: Panel Lamps with Toggle Switch
1 No: Door Switch
1 No: Space Heater - 100 Watt
Necessary Indicating Lamps
1 Set : Three Phase Indicating Lamps
Necessary Push Button
MCB - SP - as required
MCB - DP - As required
Five push buttons – start, stop, reset, test and accept.
Engine cranking relay.
Mains supply voltage sensing relay.
Vender shall provide suitable PLC for interlocking and Load management.
Vender shall provide 1000 VA UPS with 30Mint backup with dry type maintenance free battery.
Vender shall provide 24 DC battery charger suitable for panel.
The control wiring shall be operate at 24V DC.
Motorised Potentiometer for speed / voltage control shall be procured from DG manufacturer only
Energry meter shall be provided in all outgoing
DG Auto load sharing / Synchronising Panel -1 _ as described as above and as per specification complete
in all respects.
1.00 Set 4163317.00 4163317
720 MAIN LT CUM LT CHANGEOVER PANEL FOR HOSPITAL
Supply, Installation, Testing and Commissioning of Main LT Cum LT change Over Panel cubicle type,
made out of 14 swg CRCA sheet steel, totally enclosed, IP 42, protection free standing, floor mounting,
dust and vermin proof,indoor, compartmentalised, powder coated painting suitable for operation on 3
Phase and neutral, 415v, 50 Hz AC supply system with busbars extensible on both sides, interconnections
with 2.5mm2 size of FRLS copper wire, control circuit with breaker control switch & auto/ manual selector
switch, spring charging indication, ammeter, ammeter selector switches voltmeter, voltmeter selector
switches, indicating lamps CT's, multifunction meters internally wired, interlocking and having following
incomer & Bus coupler Air circuit breakers and outgoing Air circuit breaker/ Moulded case circuit breaker
complete with releases for protection all as shown on drawing including supply & installation complete as
required items and as per specifications (Panel, 35 kA for 1 sec. Copper bus bars with heat coloured
shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as aboveeDB-2.2,2.3,2.4_ described as above
- 4 No.
MDB -5 described as above
dia. LM 79 and LM80 reports need to be submitted from
Signature of EPIL Signature of Bidder
720.01
Each Incomer shall have one set of the following items:
Intelligent multi function digital meter with Capability of Disturbance Direction Detection, Sag & Swell
Monitoring with Waveform Capturing, Class of accuracy: 0.2S as per IEC62053-22, Sampling Rate of 256
Samples/Cycle, Harmonics analysis upto 63rd order for Voltage & Current, RS485 PORT & Dual Ethernet
PORT
5 Set of Indication Lamps, LED type, R,Y,B with 2 Amp control MCB and breaker 'ON', 'OFF', 'TRIP' &
spring charged lamps.
Breaker failure protection.
BUS BARS
3000 Amps TPN, 80 kA for 1 sec. Aluminiun bus bars with heat coloured shrinkable insulation sleeve. - 1
Set
BUS COUPLER
2 Set of ACB, 1600 Amps, 100kA, 4 Pole, (EDO) without release with Electrical interlocking arrangement
with incomer breakers as per single line diagram, Motor wound spring charged closing mechanism,
horizontal Drawout type including Auxilary contactor & control MCB's. if any.
6 Set Indication Lamps, LED type, for RYB with 2 Amp control MCB & breaker 'ON', 'OFF', 'TRIP' & sp 6A
MCB.
Bus Bars
250 Amps TPN, 35 kA fo720.02 OUTGOING
12 No.800 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
6 No.630 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
3 No.400 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
3 No.250 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
5 No.160 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• S, 35 kA for 1 sec. Copper bus ba
Signature of EPIL Signature of Bidder
720.03 1 No.125 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
3 No.100 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
33 Set each outgoing Indication Lamps, LED type, for RYB with 2 Amp control MCB& breaker 'ON', 'OFF',
'TRIP' lamps with 2 Amp control MCB.
Vender shall provide suitable PLC for interlocking and Load management for all incommers and
Buscouplers.
All outgoing shall have Energy meters with features like Class of accuracy: 1 as per IEC 62053-22/21,
Avg Volt, Avg Amp,Total active power & energy delivered as measured by the meter .
Potential free contact shall be provided to remote starting facilities of each starter through BAS.
The control wiring shall be operate at 24V DC.
Wiring with space heater, t 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U
1.00 Set 4882446.00 4882446
721 375 kVAR CAPACITOR PANEL FOR HOSPITAL
Supply, Installation, Testing and Commissioning of Automatic Power Factor Corrector Panel, 375 kVAR
(2X100KVAR +2 x 50 kVAR +2 x 25 kVAR+2 x 12.5 kVAR) + active capacitors, 3ph, 415V, totally
enclosed, free standing, floor mounting, dust and vermin proof, cubicle type to be fabricated out of 14
guage CRCA Sheet steel, with provision for capacitor mounted inside the panel with Busbars,
interconnections, adequate number of louvers and powder coated with approved shade including supply &
installation of following components and as per technical specifications(Panels shall be of TTA conforming
to IEC 61439/1), IEC61921
INCOMER
1 No. ACB, 800 Amps, 80kA, 4 Pole with microprocessor release Manullay spring charged closing
mechanism (MDO), horizontal drawout type.
1 Set of 1250A 80kA TPN Aluminium conductor busbar.
1 Set of Digital Voltmeter of suitable range for 3 phase, 4 wirre operation with LED display and built-in
selector switch along with 2 Amp MCB for controlling.
1 Set o, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as aboveeDB-2.2,2.3,2.4_ described as above
- 4 No.
MDB -5 described as above
dia. LM 79 and LM80 reports need to be submitted from a NABL/UL accr
Signature of EPIL Signature of Bidder
721.01 2 No. 100 kVAR Super heavy duty type units with 14% detune filter.
2 No. 50 kVAR Super Heavy Dutyheavy duty type units with 14% detuned filter
2 No. 25 kVAR Super Heavy Dutyheavy duty type units with 14% detuned filter
2 No. 12.5 kVAR Super Heavy Dutyheavy duty type units with 14% detuned filter
2 No. Capacitor duty contactor 250A for 100 kVAR with over load relays.
2 No. Capacitor duty contactor 110A for 50 kVAR with over load relays.
2 No. Capacitor duty contactor 63A for 25 kVAR with over load relays.
2 No. Capacitor duty contactor 40A for 12.5 kVAR with over load relays.
2 No. 200 A TP+N 50kA MCCB with Microprocess release with adjustable inbuilt Over Load, Short Circuit
and Earth Eault protection with extended rotory handle
2 No. 125 A TP+N 50kA MCCB with Microprocess release with adjustable inbuilt Over Load, Short Circuit
and Earth Eault protection with extended rotory handle
2 No. 63 A TP+N 50kA MCCB with Microprocess release with adjustable inbuilt Over Load, Short Circuit
and Earth Eault prote 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set721.02 10 Set A/M Selector Switch.
4 Set of Axial flow fans with thermostate
2 Set of Space heater.
1 Set of Rotary operating mechanism and terminal extension / spreaders for all the MCCB's.
Complete in all respect including all interconnections from the bus bars to MCCB and MCCB to contactor
and contactor to terminal blocks of Capacitor. Automatic Switching "ON" and "OFF" capacitor panel
described as above
2.00 Set 892733.00 1785466
722 MCC - 1 (DG Auxilary)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
2 No. 250 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with overcurrent,inbuilt Earth Fault and short circuit with ROH having following protection;
• Overload (adjustable microprocessor based)
• Short-circuit (fixed magnetic )
2 No. 250 amps 4P AC-3 Contactor following :
• Overload (adjustable microprocessor based)
• Short-circuit (fixed magnetic )
Metering & Indication
2 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
2 No. Digital Electronic Energy M 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above
Signature of EPIL Signature of Bidder
722.01 Outgoing
10 No. suitable rating MPCB for 2.5 KW DOL starter and outgoing feeder to DG Fan enclosure Fan motor
(including 1No. standby). Each compartment shall contain auto / manual selector swtich and indicating /
push button lamps with MCB for ON / OFF / TRIP of motor.
3 No. suitable rating MPCB for 1 KW DOL starter and outgoing feeder to DG Fan enclosure Fan motor
(including 1No. standby). Each compartment shall contain auto / manual selector swtich and indicating /
push button lamps with MCB for ON / OFF / TRIP of motor.
2 No. 63 amps 4 Pole Minuture Case Circuit Breaker Ics= Icu 10 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
4 No. 40 amps DP Minuture Case Circuit Breaker Ics= Icu 10 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
MCC - 1_ described as above
1.00 Set 326147.00 326147
723 DG Set & ACCESSORIES
Supply, installation, testing and commissioning of Diesel Generator Set comprising of 750 kVA prime
continuous (actual) rating raditor coolled diesel Engine in acoustic enclosure with rated capacity of suitable
BHP at 1500 RPM, direct electronic fuel injection type vertical 4 stroke, 12/16 cylinder, electronic governor,
power command control module (PCC-3.3, Cummins or equiv) along with base frame coupled to alternator
capable of delivering true 750 kVA output at 47 Deg temprature (600 KW at 0.8 power factor) brushless
type 415V, 50 Hz, self exciting alternator with residential silencer, Lube Oil System, Electronic Governor,
Batteries, Battery charger, Instrumentation, 990day oil fuel tanks, Silencer with bellows, alarms, Engine
Control Panel, AVM pads, AVR Panel, QDCT for syncronizing,Terminal arrangements including bus duct
box with all other associated equipment / work as per specifications.
Note: Day oil storage tank fabricated from 4 mm thick MS plate. Tank shall include 450 mm ID ma 6A
MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described as aboveSDB-3.1,3.3,3.4_ described as aboveO
3.00 Set 4595279.00 13785837
724 EXHAUST PIPE
Supply and fixing of following sizes of MS pipe as per IS 1239 for exhaust piping complete with
bends,supports,flanges welding etc.for exhaust of DG Set including painting, supplying & wrapping 150
mm thick minral wool thick insulation of density 150 Kg per cubic meter on all sides of Exhaust pipe with
chicken mesh wrapping and clading with 22 SWG aluminium sheet suitable for this installation complete as
required including guide support, expansion joint, SS bellows wherever required and as per specification.
724.01 200 mm dia (NB) (6 mm thick) 130.00 M 3952.00 513760
724.02 300 mm dia. (32 mm thick insulation) 90.00 M 5535.00 498150
Signature of EPIL Signature of Bidder
725 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including
cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
HSD STORAGE AND SUPPLY SYSTEM
Inlet and outlet connections
Vent pipe.
Dip pipe assembly with calibration chart
550 mm dia manhole with cover.
Lifting lugs
MS ladder
Providing Anti corrosive treatment.
Provision for level sensor (BMS)
Earthing of HSD Tank
15000.00 kg 334.00 5010000
726 HSD storage tank as described above. 1.00 Set 46941.00 46941
727 Supply, installation, testing & commissioning of electrical driven rotary gear pumps suitable for pumping of
HSD consisting of following :
Horizontally mounted single stage capable of delivering 110 LPM at 30 Mtr. Head while running at required
1440 RPM, complete with proper connection to suction and delivery line, bypass arrangement against over
pressure.
Flame proof motor for fire protection pumping unit suitable for 400 + 10% V, 3 phase, 50 Hz AC supply and
of suitable HP for the above pumps.
Flame proof ON/ OFF push button station suitable for above motor including connection and inter
connection with starters’s installed in MCC.
Common base plate of required strength manufactured out of MS channels.
Suitable anti vibration damping arrangement with cushy foot or similar mounting arrangement.
Coupling and coupling guard for direct coupling of pump and motor.
Pressure gauge with valve on the delivery side.
Strainer at inlet.
The pump set as described above with outdoor protection duty
2.00 Set 26078.00 52156
728 Providing & fixing M.S. class ‘C’ (heavy duty) pipe & fittings like tees, elbows, junctions, unions, bends,
plugs etc. RCC pipe sleeves of larger diameter to the provided wherever the pipes are crossing the wall /
slab and sleeves as per Consultant’s requirement, including clamps hangers, nuts, bolts etc for pipe
supports from wall / ceiling and wrapping of under Ground pipe with wrapping coating material including
cutting and making hole in wall / slab and making good the same. Including a coat of Synthetic enamel
paint over two coats of primer complete as required.
728.01 25 mm dia 100.00 RM 158.00 15800
728.02 50 mm dia 40.00 RM 306.00 12240
729 Excavation of required depth and back filling with compaction in soil for HSD fuel oil piping including
ramming the earth and making good.
729.01 Pipe up to 50 mm dia 20.00 RM 532.00 10640
730 Providing & fixing Cast steel ball valves of the following sizes suitable for pressure of 10 kg/sqcm complete
with all necessary fittings
730.01 25 mm dia 30.00 No. 1363.00 40890
730.02 50 mm dia 1.00 No. 3633.00 3633
731 Providing & fixing cast steel non return valves of the following sizes G.M. suitable for pressure of 10
kg/sqcm complete with all necessary fittings
Signature of EPIL Signature of Bidder
731.01 50 mm dia 1.00 No. 2893.00 2893
732 Providing & fixing level controller for day oil storage tanks including wiring, cabling, probes with all other
accessories for automatic operation of fuel pumps complete as required.
3.00 Set 8175.00 24525
733 Providing & fixing ultrasonic level transmitter with local display unit in plant room for underground oil
storage tanks including wiring, cabling, probes with all other accessories for automatic operation complete
as required. Level indications shall be compatible with BAS.
1.00 Set 67803.00 67803
734 Providing & fixing oil flow meter with 50 mm dia flanged end for HSD service 1.00 Set 59042.00 59042
735 Providing and fixing Y/bucket strainer for oil supply line
50 mm dia
2.00 No. 3635.00 7270
736 Providing & fixing unloading point consisting of 1 No. ‘Y’ strainer, with 1 No. Ball valves on inlet, outlet & by
pass 1 No. drain valve, 1 No. 3 meter long flexible hose with necessary suitable connection for all oil
tanker outlet complete as required.
736.01 80 mm dia 1.00 No. 5652.00 5652
736.02 Providing & fixing GM collection assembly fitted with lockable brass cap suitable for local oil tanker 1.00 No. 4718.00 4718
737 Supply, installation, testing and commissioning of 900 litres capacity day oil storage tank fabricated from 4
mm thick MS plates. Tank shall include 450 mm ID manhole cover, level indicator and flanged connection
for inlet, outlet, overflow drain and probe provision for level controller. Tank shall be mounted on 2 m high
structure support with access ladder (painted with 2 coats of red oxide primer).
1.00 Set 22427.00 22427
738 Supply, installation, testing and commissioning of 900 litres capacity Buffer/ Over flow oil storage tank
fabricated from 4 mm thick MS plates. Buffer/ Over flowTank shall include 450 mm ID manhole cover,
level indicator and flanged connection for inlet, outlet, overflow drain and probe provision for level
controller. Tank shall be mounted on 2 m high structure support with access ladder (painted with 2 coats
of red oxide primer) and sump tank shall be provided blow the ground level treated with anticorrosive
treatment..
2.00 Set 16586.00 33172
Signature of EPIL Signature of Bidder
739 MDB -1&2
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 35 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No.800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with overcurrent and short circuit with ROH having following protection;
• Overload (adjustable microprocessor based)
• Short-circuit (fixed magnetic )
Metering & Indication
3 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
1000/5 amps 10VA
3 set of Phase indicating light shall be protected by 6A MCB.
Bus Ba 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleev
739.01 Outgoing
3 No.160 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
7 No.125 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
MDB -1described as above
2.00 Set 326147.00 652294
Signature of EPIL Signature of Bidder
740 MDB - 3
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 35 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No.800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with overcurrent and short circuit with ROH having following protection;
• Overload (adjustable microprocessor based)
• Short-circuit (fixed magnetic )
Metering & Indication
2 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
2 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
800/5 amps 10VA
2 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described a
740.01 2 No.160 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
1 No.125 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
1 No.100 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with Thermal based release unit with
ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
MDB -3 described as above
1.00 Set 153628.00 153628
Signature of EPIL Signature of Bidder
741 EXTERNAL LIGHTING FEEDER PILLAR (IP 55)
Design, manufacture, supplying fixing in position of outdoor type feeder pillar, metal clade, suitable for 415
volt, 3-phase, 50 Hz with suitable foundation and arrangement for incoming/ outgoing cable termination,
earthing, locking arrangement, insulated aluminium bus bars system, interconnection etc.
INCOMER
1 No. 100 amps 4P Ics= Icu 25 kA, Moulded Case Circuit Breaker with Thermal release unit with ROH
having following protection;
• Overload (Fixed thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Bars
1 Set of 150A TPN Aluminium Bus Bar with colour coded PVC Sleeves
OUTGOING
1 No. 40 A, TPN MCB, 10 KA
1 No. 63 A, TPN MCB, 10 KA
18 No. 6-32A, SP MCB, 10 KA
3 Nos. 63 A, DP MCB, 10 KA , along with 3No. 40 A 4Pole contactor and 3No. timer switch
EXTERNAL LIGHTING FEEDER PILLAR (IP 55)_ described as above
2.00 Set 71001.00 142002
742 MDB -4 (KITCHEN FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 250 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
250/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Bars
300 Amps TPN, 35 kA for 1, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation
sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as aboveeDB-2.2,2.3,2.4_ described as above
- 4 No.
MDB -5 described as abov
1.00 Set 158169.00 158169
Signature of EPIL Signature of Bidder
743 MDB -5 (LAUNDRY FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 200 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
200/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Bars
250 Amps TPN, 35 kA for 1 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described as aboveSDB-3.1,3.3,3.4_ described as aboveON', 'OFF', 'TR
1.00 Set 135469.00 135469
Signature of EPIL Signature of Bidder
744 MDB - 6 (LIFT for Hospital)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 35 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
2 No. 800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with overcurrent,inbuilt Earth Fault and short circuit with ROH having following protection;
• Overload (adjustable microprocessor based)
• Short-circuit (fixed magnetic )
Metering & Indication
2 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
2 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
800/5 amps 10VA
2 set of Phase indicating ligh, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation
sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as aboveeDB-2.2,2.3,2.4_ described as above
- 4 No.
MDB -5 described as above
dia. LM 79 and LM80 reports need to be submitted from a NABL/
744.01 4 No.200 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with microprocessor based release
unit with ROH having following inbuilt protection;
• Overload (adjustable microprocessor based )
• Earth Fault (adjustable microprocessor based )
• Short-circuit (fixed magnetic )
4 No.125 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with microprocessor based release
unit with ROH having following inbuilt protection;
• Overload (adjustable microprocessor based )
• Earth Fault (adjustable microprocessor based )
• Short-circuit (fixed magnetic )
MDB -6 described as above
1.00 Set 417854.00 417854
Signature of EPIL Signature of Bidder
745 MDB - U1 (UPS INPUT PANEL FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 35 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
2 No. 800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with overcurrent,inbuilt Earth Fault and short circuit with ROH having following protection;
• Overload (adjustable microprocessor based)
• Short-circuit (fixed magnetic )
Metering & Indication
2 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
2 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
800/5 amps 10VA
2 set of Phase indi, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1
Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB
745.01 1 No. 800 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with out release unit with ROH having
following protection;
1 Set Indication Lamps, LED type, for RYB with 2 Amp control MCB & breaker 'ON', 'OFF', 'TRIP' & spring
charged lamps with2 Amp control MCB.
Outgoing
4 No.400 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with microprocessor based release
unit with ROH having following inbuilt protection;
• Overload (adjustable microprocessor based )
• Earth Fault (adjustable microprocessor based )
• Short-circuit (fixed magnetic )
4 No.125 amps TP+N Moulded Case Circuit Breaker Ics= Icu 35 kA,with microprocessor based release
unit with ROH having following inbuilt protection;
• Overload (adjustable microprocessor based )
• Earth Fault (adjustable microprocessor based )
• Short-circuit (fixed magnetic )
MDB -U1 described as above
1.00 Set 445094.00 445094
Signature of EPIL Signature of Bidder
746 SDB - 1.1&2 (Ventilation for Hospital)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 25 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps 4P, Ics= Icu 35kA, Moulded Case Circuit Breaker with microprocessor based release unit
with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3
Nos.200/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Bars
200 Amps TPN, 35 k, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. -
1 Set
Outgo
746.01 16 No. 20 amps TP+N Moulded Case Circuit Breaker Ics= Icu 25kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
SDB - 1.1 to 1.2 (Ventilation)_ described as above
2.00 Set 226268.00 452536
747 MDB -T1 ,T3(LIFT M/C RM FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 200 amps 4 Pole , Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH & 200A 4 Pole ATS having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
200/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4p
Signature of EPIL Signature of Bidder
747.01 Outgoing
12 No.63 amps TP+N Moulded Case Circuit Breaker Ics= Icu 25 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (fixed magnetic )
• Short-circuit (fixed magnetic )
2 No.63 amps 4 Pole Miniature Circuit Breaker Ics= Icu 10 kA,with microprocessor based release unit
with ROH having following protection;
• Overload (fixed magnetic )
• Short-circuit (fixed magnetic )
MDB -T1,T3 described as above
2.00 Set 278024.00 556048
748 MDB -T2 (LIFT M/C RM FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 50 kA symmetrical at 415 volts.
Incoming
1 No. 125 amps 4 Pole , Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH & 100A 4 pole ATS having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
125/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Ba, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A
748.01 Outgoing
6 No. 63 amps TP+N Moulded Case Circuit Breaker Ics= Icu 50 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
2 No.63 amps 4 Pole Miniature Circuit Breaker Ics= Icu 10 kA,with microprocessor based release unit
with ROH having following protection;
• Overload (fixed magnetic )
• Short-circuit (fixed magnetic )
MDB -T2 described as above
1.00 Set 160892.00 160892
Signature of EPIL Signature of Bidder
749 MDB -T4 (LIFT M/C RM FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 50 kA symmetrical at 415 volts.
Incoming
1 No. 200 amps 4 Pole , Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH & 125A 4 Pole ATS with having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
200/5 amps 10VA .
749.01 Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Bars
250 Amps TPN, 25 kA for 1 sec. Aluminiun bus bars with heat coloured shrinkable insulation sleeve. - 1
Set
Outgoing
8 No. 63 amps TP+N Moulded Case Circuit Breaker Ics= Icu 25 kA,with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
2 No.63 amps 4 Pole Miniature Circuit Breaker Ics= Icu 10kA,with microprocessor based release unit
with ROH having following protection;
• Overload (fixed magnetic )
• Short-circuit (fixed magnetic )
MDB -T4 described as above
1.00 Set 192672.00 192672
750 SDB-G1 (GROUND FLOORFOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 125 amps TP+N , Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
Signature of EPIL Signature of Bidder
750.01 1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
125/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
Bus Bars
150 Amps TPN, 25 kA for 1 sec. Aluminiun bus bars with heat coloured shrinkable insulation sleeve. - 1
Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 63A 4pole MCB & 2 No. 25A 4 Pole MCB with 1No.Kwh Meter -1 Set
SDB-G1 described as above
1.00 Set 112769.00 112769
751 SDB-G2 (GROUND FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N , Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
Phase indicating light shall be protected by 6A MCB. - 1 Set
751.01 Bus Bars
200 Amps TPN, 35 kA for 1 sec. Aluminiun bus bars with heat coloured shrinkable insulation sleeve. - 1
Set
Outgoing
4 No. 40A 4 Pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4 Pole MCB & 8 No. 25A 4 Pole MCB with 1No.Kwh Meter -1 Set
SDB-G2 described as above
1.00 Set 149089.00 149089
Signature of EPIL Signature of Bidder
752 SDB-G3 (GROUND FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars:- 200 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation
sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as abo
1.00 Set 139100.00 139100
753 SDB-G4 (GROUND FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
200 Amps TPN, 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4
1.00 Set 139100.00 139100
Signature of EPIL Signature of Bidder
754 SDB-1.1 (FIRST FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 125 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
125/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
150 Amps TPN,, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as above
1.00 Set 126389.00 126389
755 SDB-1.2(FIRST FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
200/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
200 Amps TPN, 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SD
1.00 Set 138193.00 138193
Signature of EPIL Signature of Bidder
756 SDB-1.3,1.4(FIRST FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 125 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
125/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
150 Amps T, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as aboveeDB-2.
2.00 Set 126389.00 252778
757 SDB-2.1(SECOND FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
200 Amps TPN, 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described as aboveSDB-3.1,3.3,3.4_ descr
1.00 Set 156353.00 156353
Signature of EPIL Signature of Bidder
758 SDB-2.2,2.3,2.4(SECOND FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
200 A, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as aboveeDB-2.2,2.3,2.4_ described as above
3.00 Set 146364.00 439092
759 SDB-3.1,3.3,3.4(THIRD FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
150 A 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described as aboveSDB-3.1,3.3,3.4_ described as above
3.00 Set 158169.00 474507
Signature of EPIL Signature of Bidder
760 SDB-3.2(THIRD FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
200 Amps TPN,, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as abov
1.00 Set 149089.00 149089
761 SDB-4.1(FOURTH FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 100 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
100/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
150 Amps TPN 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ descri
1.00 Set 120033.00 120033
Signature of EPIL Signature of Bidder
762 SDB-4.2 (FOURTH FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 200 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
200/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
250 Amps TP, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as abovee
1.00 Set 179052.00 179052
763 SDB-4.3(FOURTH FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 160 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
160/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
200 Amps TPN 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above with 1No.Kwh Meter -1 Set
SDB-4.3_ described as above
1.00 Set 199936.00 199936
Signature of EPIL Signature of Bidder
764 SDB-4.4(FOURTH FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 125 amps TP+N, Ics= Icu 25 kA, Moulded Case Circuit Breaker with microprocessor based release
unit with ROH having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
125/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
150 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
4 No. 40A 4pole MCB with 1No.Kwh Meter -1 Set
4 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
2 No. 40A 4pole MCB & 2 No. 25A 4 pole MCB with 1No.Kwh Meter -1 Set
SDB-4.4_ described as above
1.00 Set 122757.00 122757
765 SDB-RM-UG1,U1,U2,U3&U4(GROUND FLOOR FOR HOSPITAL)
Design, manufacture, supplying fixing in position of the following front operated cubicle type, front access,
dead back, 2mm thick steel enclosed free standing, dust and vermin proof, switchboard with IP42
protection with hinged and lockable doors complete with interconnections, tinned copper crimping lugs,
bonding to earth and painting, suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system, and suitable
for a fault level of 35 kA symmetrical at 415 volts.
Incoming
1 No. 200 amps 4P, Ics= Icu 35 kA, Moulded Case Circuit Breaker with microprocessor based release unit
with ROH & 200A 4 Pole ATS having with following protection;
• Overload (adjustable thermal)
• Short-circuit (fixed magnetic )
Metering & Indication
1 set of R,Y,B phase indicating lamps each with 3 nos. 6A SP MCBs.
1 No. Digital Electronic Energy Meter with necessary protection and port for BMS communication, 3 Nos.
200/5 amps 10VA
1 set of Phase indicating light shall be protected by 6A MCB.
Bus Bars
250 Amps TPN, 35 kA for 1 sec. Copper bus bars with heat coloured shrinkable insulation sleeve. - 1 Set
Outgoing
6 No. 40A DP MCB with 1No.Kwh Meter -1 Set
8 No. 63A 4pole MCB with 1No.Kwh Meter -1 Set
UG1,U1,U2,U3&U4_ described as above
5.00 Set 204476.00 1022380
Signature of EPIL Signature of Bidder
766 Rising Mains (Sandwitch insulated Construction)
Design, manufacture, supply, assembling, installation in correct assigned position, making proper
connections, testing and commissioning of following rating 4 pole sand witch type rising mains of
aluminium bus bar with tap-off connection points at every 1000 mm intervals, expansion joints, fire barriers
including necessary support and louvers for ventilation, fabricated out of GI / Extrunded aluminium sheet
including 2 Nos. of 50 x 6 mm GI/Aluminium earthing conductor through out the length of the rising mains
(Phase sequence should be matched with the incoming breaker provided at LT Panel). Thrust pad shall be
provided for each rising main for necessary support to rising main and to prevent the bus bar expansion in
downward direction. Also end cover to close the end of rising main and to provide extra supports to bus
bars at end shall be provided. Dimension to be furnished with the offer.
766.01 630 A, Isc = 50 kA for 1 second 12.00 RM 13854.00 166248
766.02 400 A, Isc = 25 kA for 1 second 12.00 RM 10717.00 128604
767 Supply, installation, testing and commissioning of following rating Reducer for rising mains of sandwitch
construction of Aluminium bus bars with expansion joints, fire barriers including fabricated out of GI /
Extrunded aluminium sheet including 2 Nos. of 50 x 6 mm GI/Aluminium earthing conductor through out
the length of the rising mains
767.01 630 to 400 amps 4 Pole Rising Mains 2.00 No. 36076.00 72152
768 Supply, installation, testing and commissioning of following rating end flange with enclosure for sand witch
rising mains of sandwitch construction of Aluminium bus bars for end termination with expansion joints, fire
barriers including fabricated out of GI / Extrunded aluminium sheet including 2 Nos. of 50 x 6 mm
GI/Aluminium earthing conductor through out the length of the rising mains (Phase sequence should be
matched with the incoming breaker provided at LT Panel).
768.01 630 Amps Rising Mains 2.00 No. 17189.00 34378
769 Design, manufacture, supply, assembling, installation in correct assigned position, making proper
connections, testing and commissioning of following rating Adopter Boxes fabricated out of 16 gauge
CRCA sheet steel in cubical formation, dust and vermin proof, coupled with rising mains. Boxes shall be
treated with all anticorrosive process before powder coating as per specifications. 2 No. earthing terminals
shall be provided. Boxes shall be suitable for connecting of rising mains at top and aluminium cables at
bottom.The cost shall be included of MCCB/ACB.
769.01 630 Amps Amps MCCB for Rising Mains Adopter 2.00 No. 59597.00 119194
770 Supply, installation, testing and commissioning of tap off boxes made up of 14 / 16 gauge CRCA sheet
steel mounted on the rising mains including providing of following MCCB’s with operating handle as
required with all accessories and adequate space shall be provided for cable terminations.
770.01 200 Amps 4 Pole MCCB of 25 KA. 4.00 No. 28264.00 113056
770.02 100 Amps 4 Pole MCCB of 25 KA. 4.00 No. 10715.00 42860
771 Supply, installation, testing and commissioning of following rating of rising man end cap.
771.01 400 Amps Rising Mains 2.00 No. 6637.00 13274
772 LT CABLES
CONTROL CABLE END TERMINATION(SUBSTATION)
Supply of following sizes of XLPE insulated PVC sheathed aluminium conductor armoured power cable of
33 kV grade (33kV earthed system) conforming to IS 7098 (Part-II) amended upto date.
772.01 3 Core, 300 Sq.mm. 230.00 Mtr 1630.00 374900
Signature of EPIL Signature of Bidder
773 Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB
distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A, tinned copper bus
bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer) as
required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
773.01 12 way (4 + 36), Double door 9.00 No. 17321.00 155889
774 33 kV CABLE END TERMINATION
Supplying and making cable end jointing with heat shink push on type , including lugs and other jointing
materials, for following size of 3 core, XLPE aluminium conductor cable of 33 KV grade as required :
774.01 3 Core 300 Sq.mm (indoor) 8.00 Set 16889.00 135112
774.02 3 Core 300 Sq.mm (Outdoor) 4.00 Set 17776.00 71104
775 SUPPLY OF L T 1.1 kV CONTROL CABLES
Supplying of following sizes of 1.1 kV grade PVC insulated copper conductor armoured stranded Control
Cable conforming to IS :1554 complete as required and as per specifications.
775.01 4 core, 2.5 Sq.mm. Cu. Conductor cable 400.00 M 89.00 35600
775.02 7 core, 2.5 Sq.mm. Cu. Conductor cable 200.00 M 140.00 28000
775.03 12 core, 2.5 Sq.mm. Cu. Conductor cable 200.00 M 216.00 43200
775.04 19core, 2.5 Sq.mm. Cu. Conductor cable 200.00 M 329.00 65800
776 Supplying and making end termination with double brass compression gland and Copper lugs for following
size of PVC sheathed copper conducter armoured control cable of 1.1 kV grand as required.
776.01 4 C x 2.5 Sq.mm. 16.00 Set 250.00 4000
776.02 7 C x 2.5 Sq.mm. 40.00 Set 250.00 10000
776.03 12 C x 2.5 Sq.mm. 26.00 Set 358.00 9308
776.04 19 C x 2.5 Sq.mm. 12.00 Set 358.00 4296
777 Supply of XLPE insulated and PVC sheathed Aluminium conductor armoured cable of 1.1 KV grade
confirming to IS : 7098:1988 with upto date amendments of following sizes
777.01 3.5core, 300 Sq.mm. 4700.00 Mtr 696.00 3271200
777.02 3.5core, 240 Sq.mm. 3450.00 Mtr 567.00 1956150
777.03 3.5 core, 185 Sq.mm. 1150.00 Mtr 451.00 518650
777.04 3.5 core, 150 Sq.mm. 850.00 Mtr 362.00 307700
777.05 3.5 core, 120 Sq.mm. 1804.00 Mtr 305.00 550220
777.06 3.5 core, 95 Sq.mm. 1735.00 Mtr 245.00 425075
777.07 3.5 core, 70 Sq.mm. 1245.00 Mtr 202.00 251490
777.08 3.5 core, 50 Sq.mm. 568.00 Mtr 149.00 84632
777.09 3.5 core, 35 Sq.mm. 660.00 Mtr 114.00 75240
777.1 4 core, 25 Sq.mm. 827.00 Mtr 98.00 81046
777.11 3 core, 25 Sq.mm. 260.00 Mtr 81.00 21060
777.12 4 core, 16 Sq.mm. 4700.00 Mtr 77.00 361900
777.13 3 core, 16 Sq.mm. 98.00 Mtr 64.00 6272
777.14 4 core, 10 Sq.mm. 6500.00 Mtr 68.00 442000
777.15 3 core, 10 Sq.mm. 3400.00 Mtr 60.00 204000
Signature of EPIL Signature of Bidder
778 Supply of XLPE insulated and PVC sheathed copper conductor armoured cable of 1.1 KV grade confirming
to IS : 7098:1988 with upto date amendments of following sizes
778.01 4 core, 6 Sq.mm. 700.02 Mtr 158.00 110603.16
778.02 3 core, 6 Sq.mm. 800.00 Mtr 122.00 97600
779 Supply of XLPE insulated and PVC sheathed copper conductor unarmoured cable of 1.1 KV grade
confirming to IS : 7098:1988 with upto date amendments of following sizes
779.01 1 core,120 Sq.mm 420.00 Mtr 712.00 299040
779.02 1 core, 50 Sq.mm 640.00 Mtr 295.00 188800
779.03 1 core, 10 Sq.mm.(LV System earthing) 600.00 Mtr 92.00 55200
779.04 1 core, 6 Sq.mm.(LV System earthing) 799.00 Mtr 53.00 42347
780 Supplying and making end termination with brass double compression gland and copper lugs for following
size of PVC insulated and PVC sheathed / XLPE copper conductor Unarmoured cable of 1.1 KV grade as
required.
780.01 1 core, 120 Sq.mm. 48.00 Sets 533.00 25584
780.02 1 core, 50 Sq.mm. 16.00 Sets 355.00 5680
780.03 1 core, 10 Sq.mm. 16.00 Sets 124.00 1984
780.04 1 core, 6 Sq.mm. 16.00 Sets 123.00 1968
781 Providing,fixing and laying of following dia hume Pipe NP2 class(light duty) in ground with RCC
collars,jointing with cement mortor 1:2 (1cement+2fine sand) including trenching 75cm deep and re-filling
as required.
781.01 150 mm dia 10.00 RM 722.00 7220
781.02 300 mm dia 30.00 RM 875.00 26250
782 Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket,
bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in
ground (75 cm below ground level) including excavation and refilling the trench but excluding sand
cushioning and protective covering etc., complete as required.
782.01 90 mm dia (OD-90 mm & ID-76 mm nominal) 200.00 RM 256.00 51200
Signature of EPIL Signature of Bidder
783 HOT DEEP GI CABLE TRAYS, RACEWAY & JUNCTION BOXES:
Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (galvanisation
thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined
with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as
required.
783.01 100 mm width X 50 mm depth X 1.6 mm thickness 1150.00 Mtr 559.00 642850
783.02 150 mm width X 50 mm depth X 1.6 mm thickness 800.00 Mtr 621.00 496800
783.03 300 mm width X 50 mm depth X 1.6 mm thickness 600.00 Mtr 731.00 438600
783.04 450 mm width X 50 mm depth X 2.0 mm thickness 1750.00 Mtr 788.00 1379000
783.05 600 mm width X 62.5 mm depth X 2.0 mm thickness 900.00 Mtr 885.00 796500
783.06 750 mm width X 62.5 mm depth X 2.0 mm thickness 920.00 Mtr 979.00 900680
783.07 900 mm width X 62.5 mm depth X 2.0 mm thickness 920.00 Mtr 1727.00 1588840
784 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “bends”
(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections,
joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as
required.
784.01 100 mm width x 50mm depth x 1.6 mm thickness. 20.00 each 778.00 15560
784.02 150 mm width x 50mm depth x 1.6 mm thickness. 20.00 each 823.00 16460
784.03 300 mm width x 50mm depth x 1.6 mm thickness. 18.00 each 876.00 15768
784.04 450 mm width x 50mm depth x 2 mm thickness. 10.00 each 942.00 9420
784.05 600 mm width x 75mm depth x 2 mm thickness. 10.00 each 1078.00 10780
784.06 750 mm width x 75mm depth x 2 mm thickness. 8.00 each 1167.00 9336
784.07 900 mm width x 75mm depth x 2 mm thickness. 4.00 each 1312.00 5248
785 Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Tee”
(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections,
joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as
required.
785.01 100 mm width x 50mm depth x 1.6 mm thickness. 3.00 each 960.00 2880
785.02 150 mm width x 50mm depth x 1.6 mm thickness. 3.00 each 992.00 2976
785.03 300 mm width x 50mm depth x 1.6 mm thickness. 2.00 each 1052.00 2104
785.04 450 mm width x 50mm depth x 2 mm thickness. 2.00 each 1172.00 2344
785.05 600 mm width x 75mm depth x 2 mm thickness. 1.00 each 1328.00 1328
785.06 750 mm width x 75mm depth x 2 mm thickness. 1.00 each 1387.00 1387
785.07 900 mm width x 75mm depth x 2 mm thickness. 1.00 each 1494.00 1494
786 Supplying and installing following size of Hot Dipped Galvanised Iron Raceways with cover (galvanisation
thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined
with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as
required.
786.01 100 mm width X 40 mm depth X 1.6 mm thickness GI Raceways 800.00 Mtr 560.00 448000
786.02 150 mm width X 40 mm depth X 1.6 mm thickness Raceways 300.00 Mtr 693.00 207900
786.03 300 mm width X 40 mm depth X 1.6 mm thickness Raceways 200.00 Mtr 1094.00 218800
787 Providing and fixing of 150 x 150 x 50 mm deep (Nominal size) wall junction box including providing 2 mm
thick Hot deep - galvanized GI steel cover required as per specification.
50.00 No. 599.00 29950
787.01 Providing and fixing of 250 x 250 x 50 mm deep (Nominal size) wall junction box including providing 2 mm
thick Hot deep - galvanized GI steel cover required as per specification.
40.00 No. 880.00 35200
Signature of EPIL Signature of Bidder
787.02 Providing and fixing of 350 x 350 x 50 mm deep (Nominal size) wall junction box including providing 2 mm
thick Hot deep - galvanized GI steel cover required as per specification.
80.00 No 1004.00 80320
788 Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required. 600.00 RM 1681.00 1008600
789 LIGHTING FIXTURES
Supply of Recessed Mounted 2'X2' Panel LED comprising of 40W LED with non integral / integral driver,
6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be
minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of LED
light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106
from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete the job.
492.00 Each 2577.00 1267884
790 Supply of Surface Mounted 2'X2' Panel LED comprising of 40W LED with non integral / integral driver,
6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be
minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of LED
light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106
from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete the job.
1833.00 Each 2020.00 3702660
791 Supply of Surface Mounted Led tube light fixture with inbuilt rod comprising of 20W LED tube with non
integral / integral driver, 6500K color temp having 40000 burning hrs life with minimum @ L 70, system
lumen output should be minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour
rendering index of LED light should be more than 70. Submission LM 80-08 Form LED Source
Manufacturer & LM79-08 / IS16106 from NABL approved lab. Manufacturer mandatory i/c connection
wire, testing etc. to complete the job.
319.00 Each 905.00 288695
792 Supply of Recessed Mounted Led Down Lighter comprising of 15W LED with non integral / integral
driver, 6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should
be minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of
LED light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 /
IS16106 from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete
the job.
1450.00 Each 592.00 858400
793 Supply of Surface Mounted Led Down Lighter comprising of 18W LED with non integral / integral driver,
6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be
minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of LED
light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106
from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete the job.
558.00 Each 1045.00 583110
794 Supply of Recessed Mounted Led Down Lighter comprising of 18W LED with non integral / integral
driver, 6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should
be minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of
LED light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 /
IS16106 from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete
the job.
385.00 Each 732.00 281820
795 Supply of Surface Mounted Led Down Lighter comprising of 12W LED with non integral / integral driver,
6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be
minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of LED
light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106
from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete the job.
679.00 Each 697.00 473263
Signature of EPIL Signature of Bidder
796 Supply of Surface Mounted LED Down Lighter comprising of 10W LED with non integral / integral driver,
6500K color temp having 40000 burning hrs life with minimum @ L 70, system lumen output should be
minimum with efficacy > 100 lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering index of LED
light should be more than 70. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 / IS16106
from NABL approved lab. Manufacturer mandatory i/c connection wire, testing etc. to complete the job.
227.00 Each 697.00 158219
797 Supply of Wall mounted 9W LED Bulk head light fixture, LED of 1 to 3 W each assembled on single
MCPCB, having color temp 6500K & having 40000 burning hrs life with minimum @ L 70, system lumen
output should be minimum with efficacy>80lm/W. LED driver PF 0.95 & THD < 20%. The colour rendering
index of LED light should be more than 70. Housing made of CRCA powder coated frame with glare free
diffused polycarbonate cover. Submission LM 80-08 Form LED Source Manufacturer & LM79-08 /
IS16106 from NABL approved lab. Manufacturer mandatory. i/c connection wire, testing etc. to complete
the job.
98.00 Each 732.00 71736
798 supply testing and commissioning of ceiling fan 5 star rating enery efficient , including wiring the down rods
of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core
cable, including earthing and providing and fixing phenolic laminated sheet cover on the fan box etc. as
required.
984.00 No 1742.00 1714128
799 supply testing and commissioning of exhaust fan upto 450 mm sweep in the existing opening, including
making the hole to suit the size of the above fan, making good the damage, connection, testing,
commissioning etc. as required.
79.00 No 1010.00 79790
800 AREA LIGHTS
Supply, Installation, Testing and Commissioning of 70W LED based Street light, housing made up of
Pressure Die Cast Housing LM 6 Alloy/ Anti Dust Exposed Lens,sturdiness and embossed brand
name/logo name of manufacturer. The fixture should have a minimum system efficacy of 110 lumen/Watt
and a minimum system lumen output of 18000 lumens. The fixture shall have a CRI of minimum 70. The
fixture shall be designed for a system life of 50,000 hours @70% lumen maintenance. Ingress Protection
of IP66 (lamp and gear Compartment) and Mechanical Impact Resistance Rating of IK >=08.The fixture
driver should have an operating voltage range of 140-270 V, surge protection of >=3KV, PF >0.9 ,
THD<10% and SDCM<5. The fixture should be top openable & easy access to the Gear Compartment.
The driver should be BIS approved, fully potted and encapsulated with 440V Stress Voltage protection for
8 Hrs. High Cut off : 325V(+/- 15V) and Auto Restart function should also be available within the
fixture.The fixture should comply with the parameters as per IS10322. The LED driver should comply to
IEC61000-3-2 ed.3.2, 2009 for Harmonics, IEC61347 -2 -13, 2006 in Conjunction with IEC61347-1 ed.2.0,
2007 for Electrical Safety, IEC62384 ed.1.1, 2011 for performance and IEC61547 ed.2.0, 2009, CISPR-15
for EMI. Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM
79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters.
Similar to Philips BRP340 LED 184 CW HO SLC S1 PS 1xLED/Cromption-LSTN-170-CDL-A/ENDO
84.00 Nos 5929.00 498036
801 Supply, Installation, Testing and Commissioning of LED Post Top as Gate Light with a system lumen
output of 2300 lumens and a minimum system efficacy of >85 lm/W. The luminaire shall have a rated
system lifetime of 25,000 burning hours at L70. The luminaire should have a color temperature of 3000K
and CRI > 70. The luminaire shall meet IP65 with THD < 20% and PF > 0.9. The luminaire shall have
closed diffused optics with polycarbonate diffuser board. The total power consumption should not exceed
27W (including driver). Similar to BGP161 LED2300/WW PSU 220-240V 7043 IN/Cromption-LPTH20-
CDL/ENDO
4.00 Nos 4069.00 16276
Signature of EPIL Signature of Bidder
802 Supply Installation Testing Commissioning of GI 7.0 mtr octagonal Pole with 1200mm single arm Arm with
inbuilt weather proof box including CC foundation (1:2:4 cement concrete (1 cement : 2 coarse sand : 4
graded stone aggregate 40mm nominal size) including excavation & refilling etc minimum size 350mm
x350mmx500mm with 300mm x 300mm x10 mm Base plate including 4 Nos. heavy duty foundation nut
bolts with suitable length as required and complete in all respect as per direction of Engineer in Charge
84.00 Nos 9716.00 816144
803 Supply and Installation of 4.5 meter high Decorative MS pole (3.6 meter above and 0.9 meter below
ground with ladder bars including chatsworth kit, junction box complete as per requirement with all
accessories.
6.00 Nos 7368.00 44208
804 UPS SYSTEM
Supply, installation, Testing and commissioning of the following rating UPS as per Technical Specifications
and complete in all respects.
160 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input harmonic
Current THD <=3% typical at 100% load, ,<=6% maximum at 50% load with Isolation Transformer and 30
min Battery backup for each UPS along with battery cabinet complete in all respect including supporting
steel structure for UPS and Battery as required.UPS shall have facility for parallel operation.
Quoted price shall be inclusive of required rating single core copper conductor cable including
terminations,connections of UPS to panels, batteries etc complete in all respect and as per direction of
Engineer in Charge.
3.00 Set 219058.00 657174
805 40 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input harmonic
Current THD <=3% typical at 100% load, ,<=6% maximum at 50% load with Isolation Transformer and 30
min Battery backup for each UPS along with battery cabinet complete in all respect including supporting
steel structure for UPS and Battery as required.UPS shall have facility for parallel operation.
Quoted price shall be inclusive of required rating single core copper conductor cable including
terminations,connections of UPS to panels, batteries etc complete in all respect and as per direction of
Engineer in Charge.
2.00 Set 678037.00 1356074
806 40 KVA UPS 3 phase (415 V + 15%) Volts input & 3 phase output (415 V + 1%), 50 Hz, Input harmonic
Current THD <=3% typical at 100% load, ,<=6% maximum at 50% load with Isolation Transformer and 30
min Battery backup for each UPS along with battery cabinet complete in all respect including supporting
steel structure for UPS and Battery as required.UPS shall have facility for Stand alone operation.
Quoted price shall be inclusive of required rating single core copper conductor cable including
terminations,connections of UPS to panels, batteries etc complete in all respect and as per direction of
Engineer in Charge.
1.00 Set 678037.00 678037
Data & Voice System
837 MATV,DATA & VOICE SYSTEM SYSTEM
Supplying and drawing co-axial TV cable RG-11 grade, solid copper conductor PE insulated, shielded with
fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC
conduit as required.
385.00 meter 118.00 45430
Signature of EPIL Signature of Bidder
838 Supply, erection, testing and commissioning of splitter / tap off mounted in suitable sizes MS boxes for
MATV system and shall be suitable for interactive system.
838.01 Four way (S-4) 10.00 Each 3007.00 30070
838.02 Four way Tap Off (T4) 29.00 Each 2506.00 72674
838.03 Supply, installation, testing and commissioning of Bi-directional line extender amplifier housed in suitable
size of MS box of CRCA sheet.
6.00 Each 7922.00 47532
839 Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor,
unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
839.01 20 Pair 50.00 meter 116.00 5800
839.02 50 Pair 100.00 meter 329.00 32900
839.03 100 Pair 50.00 meter 509.00 25450
840 Supply,Installation,testing and Commissioningof following telephone teg block
840.01 10-30 Pair 20.00 No. 2979.00 59580
840.02 50 Pair 1.00 No. 3882.00 3882
840.03 100 Pair 1.00 No. 5787.00 5787
840.04 800 Pair 2.00 No. 8897.00 17794
841 Supply & instalation of 6 core Indoor/outdoor OM3 Unarmoured Multimode Optical Fiber 200.00 Mtr 826.00 165200
842 Supply, installation, testing and commissioning of 24 port L2 Managed switch having port density 24 Nos of
10M/100M/1G RJ45 Port POE ports , 2 Nos of GbE RJ45/SFP Combo Port , 1X console port , Available
POE power 370 W , 52 Gbps switching bandwidth , 8K MAC address support , Support L2 feature STP,
RSTP ,MSTP . Support 802.1Q VLAN , port based VLAN , 4K VLAN entries , MAC based VLAN , IP
subnet based VLAN . Support IEEE 802.3ad LACP . L3 features - static routing , DHCP feature , Device
Management system - topology view , floor view , map view , dashboard , traffic monitoring , cable
diagnostics.CE,FCC certified. (Approved make - Cisco / Impulse / Juniper)
50.00 Set 69357.00 3467850
843 Supply, Installation, Testing & Commissioning of 24 port L2 Managed switch having port density 24 Nos of
10M/100M/1G RJ45 Port POE ports , 4 Nos of 1G/10G SFP+ Port , 1X console port , Available POE
power 370 W , 128 Gbps switching bandwidth , 32K MAC address support , Support L2 feature STP,
RSTP ,MSTP . Support 802.1Q VLAN , port based VLAN , 4K VLAN entries , MAC based VLAN , IP
subnet based VLAN . Support IEEE 802.3ad LACP . L3 features - static routing , DHCP server , Device
Management system - topology view , floor view , map view , dashboard , traffic monitoring , cable
diagnostics.CE,FCC certified (Approved make - Cisco / Impulse / Juniper)
4.00 Set 103008.00 412032
844 Supply, installation, testing and commissioning of CISCO/aruba /ruesh Make router (ABGN) with , CAT-
6E Port for indoor solution, suitable to creat Wi-Fi on entire floor as required.
20.00 Set 12435.00 248700
845 Supply, installation, testing and commissioning of CAT-6 Patch cabel as per EIA upto 1.2mtr length as
required.
1150.00 Set 667.00 767050
Signature of EPIL Signature of Bidder
846 Wall /Floor Mount Rack Enclosure Cabinet suitable for Data Patch Panel /Data switch , Constructed with a
hinged wall mounting bracket and a sturdy steel frame, suitable to accommodate up to 200 lbs. of
equipment in 15U of rack space. Four adjustable vertical mounting rails with square holes accommodate
all standard 19-inch rack equipment. easy access to rackmounted equipment, the enclosure cabinet is
hinged to swing away from the wall mounting bracket, perforated lockable side panels and front door,
assuring generous airflow to keep equipment operating safely. The front door shall be reversible and the
side panels are removable for easy access to equipment. The top and bottom panels of the enclosure
include convenient cable routing ports.
846.01 42U as per EAI. 2.00 Set 92865.00 185730
846.02 19U as per EAI. 1.00 Set 30678.00 30678
846.03 9U as per EAI. 18.00 Set 15132.00 272376
847 Supply, installation, testing and commissioning of following Port ,CAT-6 Loaded Patch Panel as per EAI.
847.01 24 Port ,CAT-6 Loaded Patch Panel 75.00 Set 8485.00 636375
872 SOLAR-GRID CONNECTED SYSTEM
Supplying installation,testing and commissioning of each kW power with Solar Photovoltaic system
including PV Modules aluminium super structure supported on GI support, string PCUs, Copper
maintainace free copper earthing, connection of earthing pit to SPV system including insulated copper strip
/ cables , associated power and control cabling from SPV panel to power panel and Main distribution panel
in each cluster as per specification complete in all respect as per site requirement including cabling upto
solar panel . (Inclusive of earthing for DC as well as AC equipment or system)
20.00 kwp 53529.00 1070580
Nurse call System873 CONDUITING WIRING AND CABLING FOR NURSE CALL SYSTEM
Supply ,installation, testing and commissioning of the following .
Supply, Installation, Testing & Commissioning of the system IP based controller for a decentralised
communications node for exchanging data between the connected system devices and the rest of the
communications system, consisting of :
- Metal case,
- 1 x RJ45 socket, 100Mb IP Port (IEEE802.3 100BaseTX), galvanically isolated for connection of field
devices in loop. At least 100 devices in a loop can be connected.
- RJ45 sockets, each for a 100Mb IP system port (IEEE802.3 100BaseTX) for connecting all IP capable
system modules including nurse call station. At least 6 IP devices can be connected to this switch in star
topology.
- Control LEDs for indicating the current operating state;
- All IP system modules are supplied with power using Power over LAN technology;
- Data and audio interface to a system TV device;
- Output for connecting an external amplifier.
- VDE 6A MCB.
Bus Bars
1.00 Nos. 124078.00 124078
Signature of EPIL Signature of Bidder
874 Nurse Station Terminal with antimicrobial coating having following features :
- Nurse Terminal shall comprises of required size TFT, Touch screen colour graphic display for displaying
all details
- Handset with speaker and mic.
- Speech communication facility with other nurses in network at any time.
-changeover between hands-free and discrete speaking , required size connection cable with an RJ45
connection
- a smash proof glass panel (to protect the sensitive display from unnecessary contact during cleaning and
-touch screen function keys for operating the system, call forwarding, Querying receiver for speaking
- all indication and call query according to priority. This priority is customizable.
-Indication of events, which have been forwarded from foreign systems into the system,
-Collective announcements, group interconnections,
- Facility to forward the call to desired node
- VDE 0834/ UL 1069 certified
874.01 For 6 Patient Bed Rooms with 2 Washrooms and 1 corridoor 8.00 No. 119439.00 955512
874.02 For 10 Patient Bed Rooms with 6 Washrooms and 1 corridoor 4.00 No. 119439.00 477756
874.03 For 10 Patient Bed Rooms with 4 Washrooms and 1 corridoor 4.00 No. 119439.00 477756
875 Nurse Call Module
Nurse Call Module -Bed Side Unit with Handset module (with VOIP & SIP Functionality)
It shall have following features:-
- Nurse call with possibility for communications,
- Additional calls via service call key (optional) with possibility for communications,
- Integrated IP telephone end device (H.323 or SIP protocol stack)
- Controlling electronically driven shutters or other environmental applications,
- Automatic volume switching when using the PAT in the cradle,
- Plastic case and membrane keypad in fungicidal material,
- Splash resistant case, consisting of:
- Call button with nurse symbol with integrated fi nder and reassurance light on the top end of the unit,
- Loudspeaker, microphone, headphones socket,
- A fully-graphical display with a resolution of 128 x 64 pixels.
88.00 Nos. 8815.00 775720
876 Bath/Toilet Pull cord
Supply ,Installation ,Testing and commissioning of Pull cord type call button consisting of:
- Required length pull cord with ON & OFF facility and a luminous grip
- Moisture Protection
- Aniomicrobial coating
- VDE 0834/ UL 1069 certification
56.00 Nos. 9649.00 540344
877 Supply ,Installation ,Testing and commissioning of corridoor indication consisting of:
DUAL direction LED indicator
877.01 Cooridoor Indicator 16.00 Nos. 8997.00 143952
878 Event Management Software
Providing, Installation, Testing and Commissioning of Software pack on the Management Center for
automati-cally handling of all events in the entire communications system, e.g. calls, presences, call
acknowledgements, presences etc.
This indication and analysis of the data is through a browser which has password-protected access to the
XML data on the server. Various filters make it easily to find and display the required information.
1.00 No. 363533.00 363533
Signature of EPIL Signature of Bidder
879 IPBX
Supply, Installation, Testing and Commissioning of IP PBX (Analog + IP) hyberid as per tender
specification -24 Analog Trunk Line, 02 Port PRI Line with 60 Channel Licenses 4000 Analog Extensions ,
50 IP Users , Integrated IP Gateway for IP Extension and ITSP's,Integrated UC on Motherboard, 120
Channel DSP Resource built in (TDM to IP and Vise versa 5 Party Adhoc Conference, DECT Compatible ,
Q-Sig Compatible , SIP Compatible, Remote Maintenance , Provisioned With 6 Port 300 Mailboxes,100
Auto Attendant 25 UC Smart Client etc. It should be complete as per technical specifications & as per
direction of Engineer-in-charge.
1.00 Nos. 210714.00 210714
880 Providing On Board UC Smart Client for up to 350 Users with license Sipported with following features
Presense including status based announcements Favourites including Call status, Visual Voice Mail,
control Voicemail to e mail service, Ad hoc conferencing (up to 5 party), Call Journal, Directory
Access,Instant Messaging , Reminder etc. It should be complete as per technical specifications & as per
direction of Engineer-in-charge.
3.00 Nos. 58415.00 175245
881 Providing and Installation of PC based Operator Console Supported with following features Display of
Waiting Calls with type, name and telephone number, Call Status display Speedy Switching of calls,
Individual Configuration of the busy fields with directory number or name Color display of the busy status:
Call, toggle, hold , park Number Redial (last 10 destinations) Conference with up to 5 call participants
Choice of electronic telephone books: System, telephone book, outlook contacts, internal telephone bool,
ldap access etc. It should be complete as per technical specifications & as per direction of Engineer-in-
charge.
1.00 Nos. 260783.00 260783
882 Providing IP User license for SIP Phone. 20.00 Nos. 29938.00 598760
883 Supply, Installation , Testing and Commissioning of Analog Caller ID Speaker Phone. 50.00 Nos. 1336.00 66800
884 Supply, Installation , Testing and Commissioning of IP Phones. 350.00 Nos. 991.00 346850
Total in Figures135137290.26
Signature of EPIL Signature of Bidder