2(A) Schedule of Work : Tender Document Page 1 of 20 Scope...

2(A) Schedule of Work : Tender Document of 20 Scope of Work: - Internal Electrification Works of New Premises Canara Bank, Challakere, Thyagarajanagar, Chitradurga Road - Chitradurga, Shimoga C.O.

Sl. No.

Description Of Work Unit Qty Rate (In Rs.)

Amount (In Rs.)

Consultants: M/s. Vaishnavi Electricals

A INTERNAL ELECTRIFICATION WORKS OF GENERAL LIGHTING SYSTEM & TELEPHONIC SYSTEMS of Branch & ATM :-

1

Providing additional point wiring by using 2 runs of

1.5 Sq.mm and 1 run of 1 sq.mm ISI FRLS -FLAME Guard

Finolex (Code:10104 & 10103) Copper Multi strand copper PVC Insulated wire with orange strip / Poly Cab FRZH / RR Kabel (HFFR ) / Anchor

(HFFR) / L&T/KEI as per ISI 1554 / IS 694 in 19mm dia. ISI , Low Halogen, S.F.T, Rigid PVC conduit /Casing capping conduit of PRECISION/AVON Plast

/ VIP make of color Ivory/Grey as required, depending upon site condition as directed by Engineer in charge / consultant/ confirming IS 9537, Part-3 including necessary conduit accessories, run open on wall/ ceiling/ concealed/surface conduit wiring with rawl plugs, saddles & brass screws at every point 0.75 ME distance, including supply, fixing, testing and commissioning of Crabtree pica dilly/

ABB / MDS Mosaic modular/Siemens / Anchor Woods

10AX 1 way switch with indicator concealed metal box, (as per site condition) with Stripe front plate/equivalent as approved, inner plate & also providing 3 plate Ceiling rose / Hylam plate of 3mm thick on metallic junction box. This job work also involves chipping & refinishing

the wall surface/ floor area as per site condition as directed by consultant These are additional light points as per site requirement which is other than Land lord’s scope. Note: I. Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants. 2. Front plate with colour & specification has to be approved by the Consultant / Architect / Bank authorities. Different front plates for lighting,

UPS & raw power points to be used. 3. This includes one independent light point of the

PT

12


Sl. No.


Amount (In Rs.)


ATM. 1.a Repair, servicing & maintenance of already land

lord provided point wiring by using 2 runs of 1.5

Sq.mm and 1 run of 1 sq.mm ISI FRLS -FLAME Guard

Finolex (Code:10104 & 10103) Copper Multi strand copper PVC Insulated wire with orange strip / Poly Cab FRZH / RR Kabel (HFFR ) / Anchor

(HFFR) / L&T/KEI as per ISI 1554 / IS 694 in 19mm dia. ISI , Low Halogen, S.F.T, Rigid PVC conduit /Casing capping conduit of PRECISION/AVON Plast

/ VIP make of color Ivory/Grey as required, depending upon site condition as directed by Engineer in charge / consultant/ confirming IS 9537, Part-3 including necessary conduit accessories, run open on wall/ ceiling/ concealed/surface conduit wiring with rawl plugs, saddles & brass screws at every point 0.75 ME distance, including supply, fixing, testing and commissioning of Crabtree pica dilly

ABB/ MDS Mosaic modular/Siemens / Anchor Woods

10AX 1 way switch with indicator concealed metal box, (as per site condition) with Stripe front plate/equivalent as approved, inner plate & also providing 3 plate Ceiling rose / Hylam plate of 3mm thick on metallic junction box. This job work also involves chipping & refinishing

the wall surface/ floor area as per site condition as directed by consultant

PT

08

2 Providing additional dependent Plug socket point (to be housed on light point switch board) by supply & fixing 02 No’s. of Crabtree pica dilly/

Siemens / MDS Mosaic Modular / Anchor Woods 6 / 13 A Universal Socket + 02 No. above mentioned make Modular 10 AX 1 way Switch with indicator, concealed metal box as per site condition) with front plate, inner plate in the existing Lighting Switch Board including internal connections........... Note:-1. Front plate with colour & specification has to be approved by the Architect / Bank

Set

05


Sl. No.


Amount (In Rs.)


authorities. 2. Each Set = 2Nos. of Switches + 02 Nos. of Sockets 3. Each switch board should have plug point. Surface mounted box should not be used.

3 Providing point wiring same as above [A (1)] for additional Ceiling Fan points but with 01 No of

Siemens / Crabtree pica dilly/ ABB/ MDS Mosaic/ Anchor Woods Modular one way switch with indicator -

with 01 No. of Fan step speed controller including all necessary accessories including Stripes Front plate (colour & specification decided by architect / bank), inner plate Mounting box with base frame including internal connections as mentioned in A (1) above.

No’s

03

4 Providing point wiring same as above [A(1)] for Wall mounted Fan points( without regulator) but with 01 No of Siemens / Crabtree pica dilly/ ABB/

MDS Mosaic/ Anchor Woods Modular one way switch with indicator & with 01 No. 6 / 13 A Universal Socket including all necessary accessories including Stripes Front plate( colour & specification will decided by architect / bank officials), inner plate Mounting box with base frame including internal connections as mentioned in A (1) above

No’s

07

4a. Providing Independent Plug Socket Point inclusive of circuit wiring & point wiring same as above [A (1)] by supply & fixing 02 no’s. of Siemens /

MDS Mosaic / Anchor Woods Modular 6-13 A universal socket + 02 no above mentioned make Modular 10 AX

one way Switch with indicator concealed metal box or (as per site condition) with front plate, (colour & specification to be decided by architect / bank) inner plate including internal connections…. Note: - Each Set = 2Nos. of Switch + 02 Nos. of Socket. No Separate circuit wiring & point wiring measurement. Surface mounted box not to be used.

Set

02


Sl. No.


Amount (In Rs.)


5. Providing & running of 3 Run of 2.5 Sq.mm ISI FRLS- Flame Guard Finolex (Code:10105) PVC Insulated, Copper Multi strand copper wires with Orange strip as per IS 1554/IS 694 RR Kabel

(HFFR) / Poly Cab FRZH / Anchor (HFFR) / L&T/KEI in 19mm dia., ISI, Low Halogen S.F.T rigid casing capping/PVC conduit of PRECISION /AVONPLAST/VIP make Ivory /Grey as directed by the Engineer in charge /consultant as per site condition, confirming IS 9537 Part-3 including necessary conduit accessories , run open on wall ceiling / concealed with rawl plugs, saddles and brass screws, at every 0.75 ME distance Including chipping and refinishing Floor

area & wall surface for Lighting circuits. From the Branch 3-phase control DB to the Switch Boards. Including labeling and tags.................... Note: - It is important to note that load on each lighting circuit which consists of all types of lighting & fans (excluding plug socket points) should be minimum of 800W, failing which circuit will not be considered for any kind of lesser load circuit. Also circuit length should be shortest possible as per consultant direction.

Note: I. Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants.

Mtr.

115

6. Providing same as above [A(5)] as independent

circuit wiring for strong room control ------------- And 6 A DP MCB & 16 A Socket with Plug top as master control to the strong room.—

Mtr

Set

20

01

7. Supply, Installation ,Testing & commissioning of Twin Telephone jack (RJ11) double lines, Siemens /

MDS Mosaic/ Anchor Woods modular with Stripe front

plate, inner plate mounting box & all other accessories as per site conditions, including internal connections & number ferruling.

No’s

07

8. Supply & laying of 0.5mm 2 pair PVC insulated tinned copper conductor for telephones through PVC conduits mentioned same as above (A(1)) including number ferruling &

Mtr

85


Sl. No.


Amount (In Rs.)


terminal connection Make: Finolex / Havells /Dalton.

9. Supply & laying of 0.5mm, 10 pair PVC insulated tinned copper conductor for telephones through PVC conduits same as above (A(1)) including number ferruling & terminal connections. Make: Finolex / Havells / Dalton.

Mtr

25

10. Supply & providing ISI make only approved make by the bank 10 pair Krone box with connector, ferruling & terminal connections including enclosure.

Set

01

11. Providing & running exhaust fan point wiring same as above [A (1)] for toilet & UPS room. Compulsory to provide exhaust fan points with all accessories but without fan regulator.

Pts

03

12. Fixing Testing and Commissioning of Owner supplied Light fitting of recess mounting type / surface mounting type. LED lighting, Cove Lighting, Halogen Lighting,1X36w FTL / CFL, 2X36W FTL/CFL, mirror optics, spot lights, 1x18 or 2x18 CFL down lights etc. of the branch & ATM Note : All additional accessories required for fixing the above light fittings consists of 300mm long standard down rod, GI Chain, Anchor bolt, anchor hook, teak wood round blocks, ball and socket, rawl plugs, and 3 core PVC insulated copper wires etc. are to be supplied by Contractor as per its site conditions as directed by the consultant.

No’s

37

13. Fixing, Testing & commissioning of owner supplied EXHAUST fans with all necessary accessories. All the fixing materials and 3 core PVC insulated copper wires are to be supplied by contractor as per its site conditions. (if required only)

No’s

03

14. Supply & fixing of fan hooks as per consultants direction .Note: U type hook should be welded to ceiling slab or separate clamping arrangements. (Carried out if required only for

No’s

03


Sl. No.


Amount (In Rs.)


strong room)

15. Fixing, testing & commissioning of Owner supplied ceiling fans & walls mounted fans. All the fixing materials should be supplied by the contractor. Note:-Additional down rod’s if required & 3 core PVC insulated multi strand copper wires up to 2 meters long etc. are to be supplied by Contractor as per its site conditions as directed by the consultant.-----------------------

No’s

10

16. Providing 2 Light points (Only LED down lighters

points for both branch & ATM ) controlled by 1 switch same as above [A (1)] for the Mgr. cabins and @ the banking hall (if required only) including fixing of owner supplied 1x18 W or 2x18W CFL down lighters as mentioned in [A (14)] ……… Note: - No Separate circuit wiring for the same. All LED down lighters should be of 2 light points controlled by 1 switch.

Mgr.cabin-01 set, staff back-03set & Customer lobby-02 set, & ATM -02 set i.e. for 2 down lighters

1swich control.

Set

08

17. Providing & running 3 run of 1.0 Sq.mm ISI Flame Guard FRLS (code:10104) 650 / 1100V grade Finolex PVC insulated copper multi strand copper wire RR Kabel (HFFR) / Anchor (HFFR) / L&T/KEI Equivalent Approved HFFR as per IS 1554/IS 694 in 25mm dia., ISI rigid PVC conduit PRECISION/AVONPLAST/VIP make Grey with all necessary conduit accessories run open on wall ceiling, concealed with rawl plugs, saddles & brass screws at every 0.75 ME distance including Siemens / MDS Mosaic / Anchor Woods Modular call bell switch/ with or without

remote and with call bell including lugs & end terminations................... Note: Tune/ Sound of call bell is as per Bank officials/ Architect.

No’s

01


Sl. No.


Amount (In Rs.)


18. Providing & running 2 run of 6 Sq.mm & 1 run of 2.5

Sq.mm ISI Flame Guard FRLS 650/1100V Grade

FINOLEX (Code:10107 & 10105) PVC insulated copper multi strands copper wire with orange strip/ Poly Cab FRZH / RR Kabel (HFFR ) as per IS

1554/IS 694 run in 19mm dia., ISI Low Halogen S.F.T casing capping rigid HDPE blue threaded PVC conduit of PRECISION / Avon Plast/VIP Grey depending upon site condition with all necessary conduit accessories run open on wall/concealed on wall and above false I with rawl plugs, saddles & brass screws at every 0.75 ME distance including chipping and refinishing

the wall/ floor area as per site conditions including labeling & tag.............(glow sign board wiring) Note:- Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants.

Mtr.

10

19. Providing & running 4 run of 10 Sq.mm & 1 run of

4 Sq.mm ISI Heavy duty Finolex (code:14208 & 14206) 650/1100V grade Finolex PVC insulated copper multi strand copper wires as per IS 1554/IS 694 or equivalent Polycab FRZH/ RR Kabel

HFFR in 32 mm dia., ISI, rigid blue threaded PVC conduit PRECISION / AVON PLAST/VIP make Grey with all necessary conduit accessories run concealed / Trays on wall ceiling with rawl pugs, saddles & Brass screws at every 0.75 ME distance from the Land lord panel board up to the Branch main Lighting & UPS control panel board placed near the entrance at Security arm guard

area, including lugs, glands & end terminations. This job works Includes chipping and refinishing

Floor area & wall surface.

This work is to be primarily carried out by Land lord’s scope. If land lord does not carry out only then with the consent from the bank it will be carried.

Mtr.

20


Sl. No.


Amount (In Rs.)


Note: I. Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants. 2. All the wiring care to be drawn through the shortest distance possible as directed by consultant.

20. Providing Master Lighting circuit control @ the branch entrance by using 2x 4 sq.mm+ 1x1.5 sq mm above mentioned copper wires in Lum sum measurement & details of [A1] from 3-phase branch DB including 16 A DPMCB in suitable metal double door IP-43 class protection enclosure. Note:- No Separate circuit wiring measurement Note: - this panel board will be housed @ branch entrance. Make :- DB & MCB’s are of Merlin Gerin / ABB/

Siemens/ Schneider / GE /L&T with 10 KA Capacity with D curve

Set

01

21. Master Lighting & UPS Panel Board: S/I/T/C of 3 ph. 440V, Lighting & UPS distribution board – TPN DB- metal double door IP 43 protection, Merlin Gerin / L&T/ Siemens/ Schneider/ ABB/GE make MS sheet steel enclosure distribution board, surface mounting having 35mm din rail for mounting MCB's neutral bar for each phase, earth bar with IP 43 protection class with powder coated mat finish distribution board consists of following: i) TPN Metal double door DB - 01 No. ii) 63A, TPN MCB, 10kA (incomer) - 01 No. iii) 16A, (2module) RCBO, 300mA (Raw power) ------ 01 No. iv) 63A DP MCB, 10kA (for branch UPS i/p Control) ---01

No. v) 40A/32 DP MCB, 10kA (for ATM UPS i/p Control) ---

01 No. vi) 10A/6A DP MCB, 10kA (for Strong room

Set

01


Sl. No.


Amount (In Rs.)


Control) ---01 No. vii) 25A / 32A DP MCB (for glow sign board Control) ---01 No. ix) 16A DP MCB (for lighting Control)-01No. x) 6A SP MCB (lighting sub ckt’s & Raw power sub circuits) ------ 06Nos. xi) Dummy plates- 04 Nos. As mentioned above MCB’s are with 10 KA capacity & D curve Make :- Merlin Gerin/ L&T / ABB/ Siemens/ Schneider/GE

Note: D.B's, RCBO’s, TP MCB, DPMCB & SP MCB's are of above mentioned make. All the distribution boards should be of MS Sheet steel enclosure metal door, Powder coated Matt finish & D curve 10KA MCB's including earth bar and neutral bar (for each phases) with 35mm DIN rail for mounting MCB's with IP 43 protection class. Use color coded FRLS wires for internal connections including minimum of 45 cm of circuit wiring should be made available inside the distribution board. The D.B including copper lugs, ties & tags & labeling & is of concealed type. Note: - This D.B is placed near the branch entrance @ security arm area.

B. ELECTRIFICATION WORKS OF UPS & COMPUTER SYSTEMS of Branch & ATM:

1. Providing & running 3 Run 2.5 Sq.mm ISI FRLS Flame

Guard Finolex (Code - 10105) PVC insulated copper multi strand wire with orange strip /

Poly Cab FRZH / RR Kabel (HFFR )/ Anchor (HFFR) /

L&T/KEI / as per IS 1554/IS 694 in 19mm dia. ISI Low Halogen S.F.T rigid PVC conduit of PRECISION/A1/ any ISI make (Grey color) as directed by the Engineer in charge/ consultant as per site condition confirming IS 9537 Part -3 including necessary conduit accessories run open on wall ceiling / concealed with rawl plugs, saddles & Brass Screws at every 0.75 ME

Mtr.

110


Sl. No.


Amount (In Rs.)


distance . This job work Includes chipping and

refinishing the wall/floor area as per site conditions for computer terminal plug point wiring including labeling tag and ferrules Note: I. Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants. 2.All the wiring care to be drawn on cable tray/ Floor through the shortest distance possible as directed by consultant Note: - for minimum 3 / 4 computer nodes use one circuit, If less than that circuit wiring will not be considered. Circuit length should be shortest possible as per consultant Floor cutting & refinishing is necessary to draw the circuit for runners/ work stations.

2. S/I/T/C of 1 ph. 230V computer terminal sub distribution board( Branch UPS out put sub DB) of 08 way, metal double door IP 42 protection, Merlin Gerin / Siemens/ Schneider/ ABB/ GE/L&T make MS sheet steel enclosure distribution board, surface mounting having 35mm din rail for mounting MCB's neutral bar for each phase, earth bar with IP 42 protection class with powder coated mat finish distribution board consists of following: For branch UPS output control i) 8 way double door DB - 01 No ii)25A DP MCB (incomer) ---01 No iii) 6A SP MCB ……06Nos Make :- DB & MCB’s are of Merlin Gerin / ABB/ Siemens/ Schneider / GE /L&T with 10 KA Capacity with D curve

Note: D.B's DPMCB, SP MCB's are of above mentioned make. All the distribution boards should be of MS Sheet steel enclosure metal door, Powder coated Matt finish, including earth bar and neutral bar (for each phases) with 35mm DIN rail for mounting MCB's with IP 42 protection class. Use color coded FRLS

Set

01


Sl. No.


Amount (In Rs.)


wires for internal connections including minimum of 45 cm of circuit wiring should be made available inside the distribution board. The D.B including copper lugs, ties & tags & labeling.

3. S/I/T/C of 01 No. of MDS Mosaic modular/Siemens

/ Anchor Woods 16AX 1 way modular 16 Amps one way switch with indicator and 03 no’s of above mentioned Modular 6/16 amps 3 pin combined shutter socket front plate with inner plate, mounting box clipped with base frame including internal connections. Note: - 1.Front plate with colour & specification has to be approved by the Architect / Bank authorities. 2. Different front plates for lighting, UPS & raw power points to be used. 3. Compulsory to use GI Box on wooden paneling/ wooden runners 4. 10 no’s for branch, 3 no’s for E-lobby if required only & 02 no’s for ATM.

Set

15


2.5 Sq.mm ISI 650/1100V Grade FINOLEX (Code:10107 & 10105) PVC insulated copper multistrand wire with orange strip Poly Cab FRZH

/ RR Kabel (HFFR )/ Anchor (HFFR) / L&T/KEI as per IS

1554/IS 694 run in 19mm dia., ISI Low Halogen S.F.T casing capping rigid PVC conduit of PRECISION/Avon Plast/VIP Grey depending upon site condition with all necessary conduit accessories run open on wall/concealed on wall and above false I with rawl plugs, saddles & brass screws at every 0.75 ME distance including chipping and refinishing the wall/ floor area as per site conditions from Main DB to the UPS DB to be placed in the banking hall including labeling & tag ----- Note: I. Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants.

Mtr

26


Sl. No.


Amount (In Rs.)


2.All the wiring care to be drawn on cable tray/ Floor through the shortest distance possible as directed by consultant

5. Supply, Installation Testing commissioning of Industrial type plug - socket D. with 32 A 3 pin Metal Clad type industrial socket, Make: - Merlin Gerin/ L&T / ABB/ Siemens/ Schneider/GE with 20A/32A/25A DP MCB,10kA, D curve all housed in sheet steel enclosure including all internal connections for UPS input & Output & is of surface mounted type.

No’s

03

C. Electrification works of Air Conditioner & Raw power Circuits:-

1. Providing & running 2 run of 6 Sq.mm and 1 run of

2.5 Sq.mm ISI Flame guard FRLS (code:10107 & 10105) 650/1100V grade Finolex PVC insulated copper multi strand wire with orange strip as per IS 1554/Is 694 RR Kabel (HFFR) / Poly Cab FRZH in 25mm dia., ISI Low Halogen S.F.T rigid PVC conduit of PRECISION make black/ Grey depending upon site condition or any other ISI make Low Halogen S.F.T confirming IS 9537 Part-3 including necessary conduit accessories run open on wall / ceiling / concealed, with rawl plugs saddles & brass screws at every 0.75 ME distance. Including chipping and refinishing the wall for AC circuits (1.0TR/1.5TR/2.0TR)

AC1 + AC2-01 Ckt, AC3-01 Ckt,& AC4 + AC5-01 Ckt.

Mtr.

60

2. Supply, Installation Testing commissioning of Industrial type plug - socket D. with 32 A 3 pin Metal Clad type industrial socket, Make: - Merlin Gerin/ L&T / ABB/ Siemens/ Schneider/GE with 20A/32A/25A DP MCB,10kA, D curve all housed in sheet steel enclosure including all internal connections for AC input & is of surface mounted type. (1.00TR -01 No, & 1.5 TR-04 Nos.)

Set

05

3. Raw power requirements : Providing & fixing Raw power socket of make:01 Crabtree Piccadilly modular/ MDS Mosaic


Sl. No.


Amount (In Rs.)


modular/Siemens / Anchor Woods of 01 No.16AX 1 way with indicator of modular type and 02 no 6-16 Amps socket of white front plate with inner plate mounting box & all other accessories including internal connections……………. Note: - 1.Front plate with colour & specification has to be approved by the Architect / Bank authorities. 2. Different front plates for lighting, UPS & raw power points to be used. 3. Compulsory to use GI Box on wooden paneling/ wooden runners 4.Both for branch & ATM.

Set

07

4. Raw power requirements: Providing & running 3 Run 2.5 Sq.mm ISI FRLS Flame Guard Finolex (Code - 10105) PVC insulated copper multi strand wire with orange strip Havells HFFR/ Poly Cab FRZH / RR

Kabel (HFFR )/ Anchor (HFFR) / L&T/KEI / as per IS

1554/IS 694 in 19mm dia. ISI Low Halogen S.F.T rigid PVC conduit of PRECISION/A1/ any ISI make (Grey color) as directed by the Engineer in charge/ consultant as per site condition confirming IS 9537 Part -3 including necessary conduit accessories run open on wall ceiling / concealed with rawl plugs, saddles & Brass Screws at every 0.75 ME distance. Including chipping and refinishing the wall/floor area as per site conditions for raw power plug point wiring including labeling tag and ferrules Note: I. All the wiring care to be drawn on cable tray/ Floor through the shortest distance possible as directed by consultant. 2. For minimum 5 raw power nodes use one circuit to be made, If less than that circuit wiring will not be considered. Circuit length should be shortest possible as per consultant. Floor cutting & refinishing is necessary to draw the circuit for runners/ work stations.

Mtr.

40



Sl. No.


Amount (In Rs.)


4 Sq.mm ISI Heavy duty Finolex (code:14208 & 14206) 650/1100V grade Finolex PVC insulated copper multi strand copper wires as per IS 1554/IS 694 or equivalent Polycab FRZH/ RR Kabel

HFFR in 32 mm dia., ISI, rigid blue threaded PVC conduit PRECISION / AVON PLAST/VIP make Grey with all necessary conduit accessories run concealed / Trays on wall ceiling with rawl pugs, saddles & Brass screws at every 0.75 ME distance from the Land lord panel board up to the Branch 3-phase main AC power control panel board to be placed near the entrance at Security

arm guard area, including lugs, glands & end terminations. This job works Includes chipping and

refinishing Floor area & wall surface.

This work is to be primarily carried out by Land lord’s scope. If land lord does not carry out only then with the consent from the bank it will be carried. Note: I. Bank reserves the right to test all the wires used at the site from the statutory bodies, in presence of Bank Officials/Consultants. 2. All the wiring care to be drawn through the shortest distance possible as directed by consultant.

Mtr.

25

Quotes

Only

21. AC Panel Board: S/I/T/C of 3 ph. 440V, Lighting & UPS distribution board – TPN DB- metal double door IP 43 protection, Merlin Gerin / L&T/ Siemens/ Schneider/ ABB/GE make MS sheet steel enclosure distribution board, surface mounting having 35mm din rail for mounting MCB's neutral bar for each phase, earth bar with IP 43 protection class with powder coated mat finish distribution board consists of following: i) TPN Metal double door DB - 01 No. ii) 63A, TPN RCBO, 300mA10kA (incomer) - 01 No.(incomer)


Sl. No.


Amount (In Rs.)


iii) 16A, SP MCB, 10kA, D curves ------ 01 No.(Manager cabin AC) iv) 25A / 32 A SP MCB, 10kA, D curve - 04 No. V) Dummy plates- 04 Nos. As mentioned above MCB’s are with 10 KA capacity & D curve Make :- Merlin Gerin/ L&T / ABB/ Siemens/ Schneider/GE

Note: D.B's, RCBO’s, TP MCB, DPMCB & SP MCB's are of above mentioned make. All the distribution boards should be of MS Sheet steel enclosure metal door, Powder coated Matt finish & D curve 10KA MCB's including earth bar and neutral bar (for each phases) with 35mm DIN rail for mounting MCB's with IP 43 protection class. Use color coded FRLS wires for internal connections including minimum of 45 cm of circuit wiring should be made available inside the distribution board. The D.B including copper lugs, ties & tags & labeling & is of concealed type. Note: - This D.B is placed near the branch entrance @ security arm area.

Set

01

D. Earthing works:

1. Dedicated Earth providing copper plate earthing as per IS : 3043 – 1987 consists of following : a) TATA class B GI Pipe of 2.5mtrs long, b) 2 run of 19mm x 3 mm copper strip run up

to the top of the GI pipe top (total length of the strip 5 mtr’s.) copper strip tapping terminal watering Funnel.

c) Salt 25KG + charcoal 45 KG. d) PCC chamber & CI frame e) Earth test joint consist of 19 x 3 mm copper

strip mounted on porcelain insulator 1.5 mtrs above the ground level inside the branch.

f) Copper plate 300 x 300 mm x 3.15 mm g) 2 run of 19 mm x 3 mm copper strip in


Sl. No.


Amount (In Rs.)


water PVC conduit run up to the earth test joint (2 x 8) mtrs from the top of the watering funnel

Note: Earthing should be certified from the branch manager / CO Security officer. (UPS Earthing & Lighting & UPS master control panel earthing @ Land lord area.)

Set 01

1.a. Same as above[D1], but without copper plate If Land lord does not carry out only then it will be carried out

Set

01

Quotes

Only

2. Providing earth test joint- copper plate of 80mm long & 40mm X 6mm with provision for fixing copper strips. Earth test joint is to be provided at 1.5 Mtrs from G.L on to the R.C.C Building / or inside the Bank premises …………. Separate for UPS and others

Set

02

3. Supply & laying 8 SWG copper strip / 1Run of

10sq.mm green color multi strand copper conductor as above mentioned makes , PVC insulated wire in HDPE conduit from the earth test joint to various locations @ the branch premises distribution boards & equipments etc.

Mtrs

25

4. Providing detail electrical lay out & wiring: ( separate drawings for A.C, UPS, Raw Power, Lighting & Telephone ) Auto cad drawing of A3 size, each drawing of 02 Laminated copies & soft copy. Also earthing & earthing lay out drawing. All these drawings are to be approved by Consultant

LS

01

E. Supply of LED Lighting Fixtures & Fans: Note: Technical Specifications of the LED lighting as enclosed format to be filled along with bidder’s compliance for the approval before perches & installation

1. Supply of 25W LED luminaries suitable for Armstrong ceiling and grid ceiling complete with HF electronic driver. Supply @ site the 2ft.x2ft.recess mounted, LED


Sl. No.


Amount (In Rs.)


ceiling Panel Lights, 120V-270VAC, 25W or below but not less than 18W, cool white/ Warm white, IP-20 protection, 110-120 degree angle, life hours > 50,000 hours, driver circuit with software, housing is fabricated from CRCA sheet, powder coated in white, with high power LED’s mounted back lifted tray &

Perforated front frame with translucent cover fixed to the housing, including all accessories as complete one set as required. The fitting should get fixed in the existing false ceiling cutting of 2ft.x2ft. Fixture Make:------------------- Discount offered:---------------- LED make:-------------------- Lux:----------------------- Make:- Wipro: (LM11-025-XXX-WH-XX 25 x 1W class LED / LM11-036-XXX-WH-XX 36 x 1W class LED) or

Equivalent Havells/Bajaj/ Crompton Greaves/Philips/Syska/Sun power/ VIN (VIN-

Grille Light 24W /VIN C 2x2 ) or any other approved by Bank

Set

10

Quotes

Only

2. Supply @ site the recess mounted 4W/5W/6W LED Down Lighter consists of recess mounted pressure die-cast aluminum luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and separate

replaceable HF electronic driver with high power LED’s including all accessories as complete one set as required.(for branch) Fixture Make:------------------- Discount offered:---------------- LED make:-------------------- Lux:----------------------- Make: Havell’s: code: ENDURA DL 7W: 7W LED 3K LHEBFUP5IZ1W007 Diffused. Wipro: SPOTZ LD:LD 35: LD35-400-xxx-50 xx Crompton: iLED 5w:LCDR LW-5T Bajaj: 110998 BGSLD(9W) 03 03WH VIN: VIN D6

Set

16

Quotes

Only


Sl. No.


Amount (In Rs.)


Equivalent : Syska/Sun power/Philips or any other approved by Bank

3. Supply of Wall / Ceiling mounted LED batten, extruded aluminum heat sink provided for efficient heat dissipation & integrated HF electronic driver. Supply @ site the Wall/Ceiling mounted LED Lights, 200-240VAC, T8 – 4 feet-16W/20W,Single,cool white/Warm white, of dimension:1200mmx28mm/30mm, driver circuit with software, aluminum material/ housing is fabricated from CRCA sheet, powder coated in white, with high power LED’s including all accessories as complete one set as required. Make: Havell’s: code: 20W LED 6K LHCD01102674

Diffused / equivalent Wipro/ Bajaj/ Crompton/Philips/Syska/Sun power/VIN or any other approved by Bank

Set

04

4. Supply @ site the 1x 40 W FTL surface mounted Patti type fitting with copper choke and 40 W FTL lamps Make: Wipro- WCP / Equivalent Philips/ Thorn/ Bajaj / Asian/ Crompton Greaves Lamp make: OSRAM/ PhilipsSupply @ site the

Set

05

4.a Supply @ site 1x18w CFL Open type- Pin type ordinary for toilets

Set

02

5. Supply @ site the energy efficient 48” ceiling Fan Colour: Ivory white / White as approved by the Consultant. Make: Almonard/ Crompton greaves/ Bajaj/ Usha

Set

03

6. Supply @ Site the energy efficient Wall Mounted Fan Colour: Ivory white / White as approved by the Consultant. Make: Almonard/ Crompton greaves/ Bajaj/ Usha

Set

07

7. Supply @ site the ISI approved cash cabin Fan Set 02


Sl. No.


Amount (In Rs.)


8. Supply @ site the ISI approved exhaust fan 900rpm of approved make

Set 03

9. Supply, installation, testing & commissioning of MS enclosure & key &consists of following: [a] 63A, TPN MCB,10kA-01No.(as master control power at input to the 3-phase copper bus bar)

i. 63A copper bus bar with heat shrinkable sleeves suitably insulated, with proper clearance as per IS.

ii. with terminal extension both at input & output of the TPN MCB by using 63A copper bus bar with heat shrinkable colour coded sheets, Phase barrier, spreader links provision to terminate 4C x 16 sq mm, LT UG copper cable(input) and providing double compression gland of comet make, copper lugs & termination of the input.

iii. 19mmx6mm copper earth bus-01 no. The drawing should be approved from the Consultant. Note: - This will be installed at the land lord’s Energy meter area. If Land lord does not carry out only then it will be carried out

Set

01

10. Safety Accessories:

1) First aid Box – 01 no 2) Shock treatment chart – 01 No Mandatory to be Provide, failing which penalized.

Set

01

Rupees-------------------------------------------------------------------------------------------------------------------- Only

TOTAL: RS.

Contractor’s AUTHORISED SIGNATURE WITH THE SEAL AND DATE

Special Note: 1) The quantities mentioned in the schedule of work are approximate and may vary

and also some of the items may or may not be executed as per the actual site conditions. No claim of what so ever should be made by the contractor on account of variations, omissions, and modifications will not be entertained.


Sl. No.


Amount (In Rs.)


2) Bank reserves the right to award the work as a whole or as a part of the work as may be considered necessary.

3) Conditional tenders will not be accepted. 4) Quotations should be written in both words and figures. Quotations not written in

words are liable for rejection. 5) Test certificate should be produced for wires as mentioned above from

manufacturer with purchase details. 6) Work should complete in all respects within 30 days from the date of work order.

7) Rate quoted should be inclusive of all types of taxes, transportation, labour charges etc.

8) Make & specification should be strictly adhered to. Any variations in the same has to be carried out with the permission of the bank before proceeding of the work failing which the same will be penalized as per the discretion of the bank.

9) No separate laisoning charges will be paid for any kind of work involved towards MESCOM or electrical inspectorate.

10) Lighting fixtures & Fan bill has to be provided from authorized dealer. 11) Contractor has to take written permission from the Premises Manager / Electrical

engineer regarding the nature & directions of the work which consists of Lighting, Raw power, A.C.& UPS requirements.

Contractor’s AUTHORISED SIGNATURE WITH THE SEAL AND DATE

2(A) Schedule of Work : Tender Document Page 1 of 20 Scope...

Documents

Transcript of 2(A) Schedule of Work : Tender Document Page 1 of 20 Scope...