Preventative maintenance fitness equipment ATTIVO

Email: [email protected]

PREVENTATIVE MAINTENANCE

Protect the value of your fitness equipment

The ATTIVO Preventative Maintenance program is a great way to make sure your equipment is

performing in peak condition for your exercisers.

When your Fitness equipment is covered under a Preventative Maintenance Plan, our certified

technician will deliver regular, thorough cleaning, testing, and calibration which amounts to more

uptime for your equipment.

We offer a variety of service schedules to fit your needs. From monthly to annual arrangements, we

are there when you need us to keep your equipment up and running smoothly.

PREVENTATIVE MAINTENANCE

Regularly scheduled Preventative Maintenance visits. Choose: Monthly • Quarterly • Semi-Annual • Annual

Increases uptime of your equipment

Ability to schedule Preventative Maintenance visits at convenient time

Extends the life of the equipment

Reduces risk

Provides members with an optimum experience

Reduces club staffing requirements and/or 3rd party servicer expense

Factory-trained service technician performs comprehensive maintenance

Provides detailed diagnostic report following each Preventative Maintenance visit

ATTIVO INTERNATIONAL Co. Ltd 3rd Floor, HQ Building 193C3, Ba Trieu street,

Hai Ba Trung, Hanoi Tel: 84 435 265 999 www.attivointl.com



PREVENTATIVE MAINTENANCE CHECK LIST

Preventative maintenance is essential to extending the life of your equipment, increasing uptime, and

maintaining warranty coverage. Precor authorized servicers perform the procedures listed below by

equipment type. For more details on Maintenance Procedures refer to your Service Manual.

I. Maintenance Schedule for: TREADMILLS

DESCRIPTION SCHEDULE

Operation verification.

Verify unit sits level on floor.

Turn off power switch/circuit breaker and unplug the power cord from the wall outlet.

Inspect the power cord, make sure it is not damaged or coiled under the treadmill.

Vacuum underneath equipment.

Clean all surfaces.

Use a dry towel to clean the running belt and deck.

Verify the safety lanyard is in place and functional.

Clean the electronic console with a damp lint free cloth and dry completely.

Clean touch screen console (P80) with a diluted solution of one part 91% Isopropyl Alcohol to one part water on a damp lint free cloth and dry completely.

WEEKLY

Verify the stop clip is in place and functional.

Visually inspect the running deck and belt, make sure that the bed or belt is in good condition. Replace if necessary.

Inspect the power cord, make sure it is not damaged or underneath the treadmill. Verify the cord clamp is securely installed.

Perform functional test to verify all features are performing properly.

Clean the treadmill’s frame using a cloth dampened with an approved cleaning solution. Use a soft nylon scrub brush or a towel to clean the running belt.

Clean the floor underneath the Treadmill.

Wipe the surface of the electronic console.

Inspect visible welds, frame and wire connections.

Clean drive belt and pulley with a small wire brush.

MONTHLY


Inspect running belt and deck.

Check the tension, tracking and alignment of the running belt. Re-tension or adjust if necessary.

Check the tension of the drive belt, adjust if necessary.

Remove hood and vacuum the compartment and motor controller fan.

Perform the software diagnostics, check LED function and record the odometer reading.

Functionally test both the wireless and hand held heart rate.

QUARTERLY

*

Check the drive motor brushes, if applicable.

Lubricate lift motor screw.

SEMI-

ANNUAL**

II. Maintenance Schedule for: ELLIPTICALS CROSS TRAINER

IMPORTANT! USE EXTREME CAUTION when the rear cover is removed.

Serious injury could result if fingers are pinched between the flywheel spokes, crank arms, stair arms,

and drive weldment.





Clean all surfaces.

Use soft nylon scrub brush to clean grooves on foot pedals.



WEEKLY


Inspect and lube lift motor screw if necessary.

Remove rear covers and vacuum with a low static vacuum around the electronic board.

Clean drive belts and pulleys.

MONTHLY


Verify the wheels run smoothly on the ramp.

Clean the ramps and wheels with an approved solution.

Inspect the power cord. Ensure that the cord is not pinched under the unit.

Vacuum carpet or “damp mop” the floor underneath the EFX.

Verify the HHHR is operational.

Record the usage hours.

Verify torque setting on crank arm and pillow blocks.

Inspect belts for tension and excessive wear.

Lubricate lift motor screw with a synthetic grease.

QUARTERLY*

Verify the battery voltage. SEMI-ANNUAL**

III. Maintenance Schedule for: ADAPTIVE MOTION TRAINER

IMPORTANT! USE EXTREME CAUTION when the rear cover is removed. Serious injury could result if fingers are pinched between the flywheel spokes, crank arms, stair arms, and drive weldment.





Clean all surfaces.

Clean pedals, stairarms, upper arms and grips.



WEEKLY

Inspect visible welds, frame, and wire connections.

Lube lift motor screw.

Remove covers and vacuum with a low static vacuum around the electronic board.

Inspect tension and excessive wear on all belts and pulleys.

MONTHLY


Clean grooved drive belts and pulleys with a small wire brush.

Verify the pedals move smoothly in the vertical and horizontal axis.

Verify the HHHR is operational.

Record the usage hours.

Check the stability of machine if necessary adjust the leveling feet.

Check the tension of the drives and h-brake belts, adjust if necessary.

Inspect the gas spring shock.

Clean and lube the rear link bearings (AMT 100i only).

Verify the resistance changes through the entire range.

QUARTERLY*

Verify the battery voltage.

Visually inspect the belts for cracks, fraying or excessive wear.

SEMI-ANNUAL**

IV. Maintenance Schedule for: STATIONARY BIKES





Clean all surfaces.


Clean touch screen console (P80) with a diluted solution of one part 91% Isopropyl

Alcohol to one part water on a damp lint free cloth and dry completely.

WEEKLY

Inspect visible welds, frames and wire connections.


Clean drive belts and pulleys with a small wire brush.

Check that pedals turn freely and smoothly at resistance level 1.

Inspect the power adapter (if so equipped). Ensure that the cord is not pinched under the unit.

Verify the seat moves smoothly through the entire adjustment range and the position latch works correctly.

MONTHLY


Check the tension of the drives belts, adjust if necessary.

Verify the seat is secure.

Verify the battery charge voltage.

QUARTERLY*

Verify the battery voltage. SEMI-ANNUAL**

V. Maintenance Schedule for: CLIMBER





Clean all surfaces.


WEEKLY



Wipe down unit.

Check that pedals move freely and smoothly.

Inspect the power adapter (if so equipped). Ensure that the cord is not pinched under the unit.

Verify the HHHR works correctly.

MONTHLY

Inspect stairarms and bumpers for excessive wear.

Verify drive belts has proper tension and adjust if necessary.

Inspect springs.

Check the pedal stops are in good condition.

QUARTERLY*

Visually inspect the belts for cracks, fraying or excessive wear.

Verify the battery voltage.

Check the pedal belt clamps are torqued properly.

SEMI-ANNUAL**


VI. Maintenance Schedule for: STRENGTH

In addition to following the routine maintenance schedule outlined below you will want to do the

following daily:

Inspect cables and cable ends replacing upon any sign of wear.

Check for kinks, frayed wires or deterioration of the cable coating. Look for signs of wear

particularly at crimped ends of the cable and near pulleys.

IMPORTANT! Cables must be replaced immediately if they are damaged to avoid possible injury to

users.





Clean all surfaces.

Lube guide rods, bushings, rod ends, linear bearings, shafts and pop pins.


WEEKLY

Inspect visible welds, frame, and cable connections.


Verify proper tension on all cables.

Inspect upholstery and pads for excessive wear.

Wipe down unit.

Verify the weight stack pin tether is attached.

Verify the instruction placard is attached and intact.

MONTHLY

Check the machine motion to ensure smooth through full range of travel.

Verify the adjustments of seats fully functional and lube.

QUARTERLY*

Verify cable tension.

Inspect all weight pins to ensure they are secure.

SEMI-ANNUAL**

.


VII. Maintenance Schedule for: PERSIONAL VIEWING SCREEN ( PVS)


Wipe the screen with an approved solution. (Do not use acidic cleaners).

Verify the channel up down and volume up down function.

Verify the numeric key pad can be used to change channels.

Verify the headphone jack works.

MONTHLY

Verify the home page is correctly programmed.

Verify the video image is clear on all channels.

Verify the audio matches the video.

QUARTERLY*

Verify the channel lineup matches the facility requirements.

Verify the decorative cable cover is fully intact and properly aligned.

SEMI-ANNUAL**

*Complete all inspections listed under Monthly above plus the following.

**Complete all inspections listed under Monthly and Quarterly above plus the following.

VIII. Maintenance Schedule for: WATER ROWER / CONCEPT II


Remove dust, dirt, sweat, and other substances of cage and blades

Wipe down the entire machine except for the chain

Test the rower and the display console

MONTHLY

Clean and lubricate the chain with a light chain oil QUARTERLY*

Check the battery if the display doesn’t work SEMI-ANNUAL**

*Complete all inspections listed under Monthly above plus the following.

**Complete all inspections listed under Monthly and Quarterly above plus the following.

Preventative maintenance fitness equipment ATTIVO

Technology

Transcript of Preventative maintenance fitness equipment ATTIVO