© 2002 Eaton Corporation. All rights reserved.

Powerware9910-P11 and 9910-P16

High Performance

High Reliability & Availability

Flexible & Configurable

Advanced Communications

Fourth-Generation Online™ topology ensures continuous, clean powerAdvanced Battery Management Plus (ABM Plus™) significantly increases battery lifeExtended Battery Modules (EBMs) prolong backup timesLoad Segments enable scheduled shutdownsTwo-in-One form factor provides versatility2U rack-mount height conserves valuable rack spaceHot-swappable batteries simplify service

Product SnapshotPower Rating: 1000 VA/700 Watt

1500 VA/1050 WattVoltage: 220-240 VacFrequency: 50/60 HzConfiguration: 2U, 19” tower or rackRuntime (in min,): Half/Full load (15/5)Input line cord: IEC-320-C14 Number of outlets: 6 IEC-320-C13 Options: EBM, SNMP, rack kit

and MultiServer

P11 and P16 Features

P11 and P16 ApplicationsThe P11 and P16 were specifically designed, engineered and approved for IBM applications

iSeries and AS/400pSeries and RS/6000xSeries and other eServersStorage and networking devices

9910 UPSs are ideal power protection foriSeries family of servers

9406 7025 7043 7044

P16 with i5 520 Tower

Series 9 Power ProtectionThe P11 and P16 provide double-conversion online power protection from all 9 of the most common power problems that threaten your equipment and data

Power failures High voltage spikes

Power sags Frequency variations

Power surges Switching transients

Brownouts Harmonic distortion

Line noise

Utility Load

Internal Automatic Bypass

Battery

AC to DC Rectifier

DC to AC Inverter

Bi-Directional Power Converter

Filtering

Wide input voltage rangeReduces battery usageReserves batteries for power failures--when you need maximum runtimeExtends UPS service lifeReduces battery replacement costs

EnergyShareUnder extremely poor utility conditions, P11 and P16 models take power from both the utility and batteryReduces battery usageExtends runtime and service life of the battery

P11 and P16 Fourth-Generation Online TopologyTM

Energy Share

EnergyShare range: 120-160V(combined battery and utility)

Battery Power: <120V

Battery Power: >288V

Online voltage regulation: 160-288V

(no battery power needed)

Input Voltage RangeDuring extreme brownouts, the P11 and P16 provide an extra level of protection; the UPS “shares” battery and incoming voltage to continue to provide ±3% of nominal voltage

B CABM® Technology• Doubles battery

service life by charging only when needed

• Optimizes recharge time

• Does not trickle chargeand starve the electrolyte

• Intelligent microprocessor controlled -Only true & automatic battery check (periodic, controlled discharge) for most accurate advanced failure protection

• Sleep Feature - no unnecessary battery “drain”

Compact DesignThe P11 and P16 packs superior power protection in a sleek, compact design.

19”

17”

3.5”

Informative User Interface

On Button(Start-On-Battery)

Overtemperature

Overload

Load Level/Battery LevelBypass Mode

Alarm Silence/Test Button Off Button

Battery Mode

Normal Mode (UPS On)

Site Wiring Fault

Self-Test

Replace Battery (ABM)

Note: rotate 90° for cabinet configuration

Load Segments

Power down sequencing of Load SegmentsExtends runtime for critical devices

Power up sequencing of Load SegmentsOrderly power up of connected devices

Scheduled on/off timesTurn off equipment for security and power conservation

Individual control of two Load Segments

No need to shut down your critical load when replacing batteries

Hot-Swappable Batteries

UPS and two EBMs

Add EBMs to extend backup time

Extended Battery Modules

EBM Connection

EBM #1 EBM #2

P11 Battery RuntimesBattery Runtime (in minutes)*

Standard (Std)Watts Internal Batteries +1 EBM +2 EBMs

140 37 271 546

280 19 142 278

490 9 72 156

595 6 59 124

700 5 48 104

Rack height 2 4 6

* Up to 2 EBMs can be connected to the P11. EBM runtimes include P11 internal batteries. Runtime chart provides typical information. Battery runtimes are approximate and may vary with equipment, configuration, battery age, temperature, etc.

P16 Battery RuntimesBattery Runtime (in minutes)*

Standard (Std)Watts Internal Batteries +1 EBM +2 EBMs +3 EBMs +4 EBMs

280 46 177 331 501 682

490 25 96 180 272 370

595 21 76 142 214 292

700 16 61 115 174 237

875 11 46 87 131 179

1050 8 37 70 106 144

Rack height 2 4 6 8 10* Up to 4 EBMs can be connected to the P16. EBM runtimes include P16 internal batteries. Runtime chart provides typical information. Battery runtimes are approximate and may vary with equipment, configuration, battery age, temperature, etc.

P11 and P16 Rear Panel

REPO/Network Transient ProtectorShut down UPS remotely with REPO port; ideal for rack applications

Network Transient Protector provides protection from “back door” disturbances that travel through phone/network lines

Powerware Extensions Software for IBM Director

Seamless UPS and software integration into IBM Director Network Management System (NMS)Real time monitoring, management and alarm notification of all UPSs in the network: e.g. battery status, battery replacement, load level and metering informationAutomatically launches LanSafe and ConnectUPS Web/SNMP Card applications from within DirectorAvailable on Powerware web FREE-OF-CHARGE

Powerware Software SuiteThe industry’s most comprehensive software bundle, The PowerwareSoftware Suite, is free and included with every P11 and P16.

Software Wizard guides you through software selection and installation. In addition to multimedia demonstrations, product data sheets, and video clips, the Software Suite contains the following power management software:• LanSafe™ Network UPS shutdown and monitoring

software• PowerVision® (30-day trial version) UPS performance

analysis and monitoring software

• Foreseer® (demonstration) facility and data center management software

Power Management Software

Software ApplicationPowerware

Extensions for Application LanSafe NetWatch IBM Director

Single pSeries (serial/TTY) non-LPAR

Single pSeries (network) non-LPAR * *

Single pSeries (LPAR) *

Multiple pSeries (non-LPAR) *

Multiple pSeries (LPAR) *

IBM Director Network Device *

* Co-requisite FC 2934 ConnectUPS Web/SNMP network card.

Note: UPS for iSeries applications utilize OS/400 UPS monitoring functions.

AmbientEmail/ SSL/SSH1 Temperature

Application Monitoring Shutdown GUI SMTP Security Humidity

LanSafe Yes Yes Yes Yes / Yes No/No No/No

NetWatch - Yes - No/No No/No No/No

ConnectUPS Web/ Yes2 Yes3 Yes Yes / Yes Yes / Yes Yes / Yes4

SNMP Card (FC 2934)1SSL = Secure Sockets Layer. SSH = Secure Shell. 2Via Web Browser, LanSafe or Network Management System (e.g. IBM Director, Tivoli). 3In conjunction with NetWatch software. 4With optional FC 2938 EMP (Environmental Monitoring Probe) device attached.

Software Comparison

Software Solution zSeries iSeries pSeries xSeries Storage Networking

LanSafe

LanSafe and ConnectUPS MultiServer card (IBM FC 2933)

NetWatch and ConnectUPS !

Web/SNMP card (IBM FC 2934) LPARs

Powerware Extensions forIBM Director

NetWatch

ConnectUPS Relay card andAS/400 cable (IBM FC 2936)!Use ConnectUPS Web/SNMP/xHub card, IBM FC 2934 to support LPAR (POWER 4 Chip Set) servers. For pSeries configurations, each LPAR needs a network connection and will install Powerware provided NetWatch or LanSafesoftware.

ConnectivityWhat you need by application

P11 and P16 CollateralAdditional information available at www.powerware.com/ibm

Select your region. Click “Products”, click “9910 Solutions” then click “Powerware pSeries” or “Powerware iSeries”

Powerware UPS Hotline for IBM1-800-925-4426

Materials availableData sheetApplication overview chartProduct presentationDocuments (manuals)