Black plate (1,1)

Installation Manual

Smartphone Receiver

SPH-DA120

English

<CRD4800-A>1

Black plate (2,1)

Precautions

Your new product and this manual 3Important safeguards 3

ConnectionPrecautions before connecting the

system 4Before installing this product 4To prevent damage 5

– Notice for the blue/white lead 5Parts supplied 6Connecting the power cord (1) 8Connecting the power cord (2) 10Connecting the system 11Connecting to separately sold power

amp 12Connecting an iPhone with Lightning

connector 13– Connecting via the USB port 13– Connecting via the HDMI port 13

Connecting an iPhone with 30-pinconnector 14– Connecting via the AUX input 14– Connecting via the RGB input 15

Connecting the Android™ device 15– Connecting an Android device with an

HDMI port 15– Connecting an Android device with an

MHL port 16Connecting the MirrorLink™ device 16Securing the High Speed HDMI® Cable 17Connecting a rear view camera 18Connecting the external video

component 19– Using AV input 19– Using an AUX input 19

Connecting an HDMI device 20Connecting the rear display 21

– When using a rear display connected torear video output 21

InstallationPrecautions before installation 22To avoid electromagnetic interference 22Before installing 22Installing this product 23

– Installation notes 23– Parts supplied 24– Installation using the screw holes on

the side of this product 24Installing the GPS antenna 25

– Installation notes 25– Parts supplied 25– When installing the antenna inside the

vehicle (on the dashboard or rearshelf) 26

Installing the microphone 27– Parts supplied 27– Mounting on the sun visor 27– Installation on the steering column 28– Adjusting the microphone angle 28

After installationAfter installing this product 29

<CRD4800-A>2

Contents

En2

Black plate (3,1)

Your new product and thismanual! Do not operate this product, any applica-

tions, or the rear view camera option (if pur-chased) if doing so will divert your attentionin any way from the safe operation of yourvehicle. Always observe safe driving rulesand follow all existing traffic regulations. Ifyou experience difficulty in operating thisproduct or reading the display, park yourvehicle in a safe location and apply theparking brake before making the necessaryadjustments.

! This manual explains how to install thisproduct in your vehicle. Operation of thisproduct is explained in the separate man-uals.

! Do not install this product where it may (i)obstruct the driver’s vision, (ii) impair theperformance of any of the vehicle’s operat-ing systems of safety features, includingairbags, hazard lamp buttons, or (iii) impairthe driver’s ability to safely operate the vehi-cle. In some cases, it may not be possibleto install this product because of the vehi-cle type or the shape of the vehicle inter-ior.

Important safeguardsWARNING

Pioneer does not recommend that you installthis product yourself. This product is de-signed for professional installation only. Werecommend that only authorized Pioneer ser-vice personnel, who have special trainingand experience in mobile electronics, set upand install this product. NEVER SERVICETHIS PRODUCT YOURSELF. Installing orservicing this product and its connectingcables may expose you to the risk of electricshock or other hazards, and can cause da-mage to this product that is not covered bywarranty.

! Read this manual fully and carefully beforeinstalling this product.

! Keep this manual handy for future refer-ence.

! Pay close attention to all warnings in thismanual and follow the instructions care-fully.

! Traffic restrictions and advisories are al-ways more important than guidance givenby a third-party navigation/mapping iPhoneapplication. Always obey current traffic re-strictions, even if the application providescontrary advice.

! As with any accessory in your vehicle’s in-terior, this product should not divert yourattention from the safe operation of yourvehicle as it may result in serious injury ordeath. If you experience difficulty in operat-ing the system or reading the display,please make adjustments while safelyparked.

! Please remember to wear your seat belt atall times while operating your vehicle. Ifyou are in an accident, your injuries can beconsiderably more severe if your seat beltis not properly buckled.

! Certain country and government laws mayprohibit or restrict the placement and useof this product in your vehicle. Please com-ply with all applicable laws and regulationsregarding the use, installation and opera-tion of this product.

<CRD4800-A>3

En 3

English

Section

01Precautions

Black plate (4,1)

Precautions beforeconnecting the system

WARNINGDo not take any steps to tamper with or dis-able the parking brake interlock systemwhich is in place for your protection. Tamper-ing with or disabling the parking brake inter-lock system could result in serious injury ordeath.

CAUTION! If you decide to perform the installation

yourself, and have special training and ex-perience in the mobile electronics instal-lations, please carefully follow all of thesteps in the installation manual.

! Secure all wiring with cable clamps orelectrical tape. Do not allow any bare wir-ing to remain exposed.

! Do not directly connect the yellow lead ofthis product to the vehicle battery. If thelead is directly connected to the battery,engine vibration may eventually causethe insulation to fail at the point wherethe wire passes from the passenger com-partment into the engine compartment. Ifthe yellow lead’s insulation tears as a re-sult of contact with metal parts, short-cir-cuiting can occur, resulting inconsiderable danger.

! It is extremely dangerous to allow cablesto become wound around the steering col-umn or shift lever. Be sure to install thisproduct, its cables, and wiring away insuch so that they will not obstruct or hin-der driving.

! Make sure that the cables and wires willnot interfere with or become caught inany of the vehicle’s moving parts, espe-cially the steering wheel, shift lever, park-ing brake, sliding seat tracks, doors, orany of the vehicle’s controls.

! Do not route wires where they will be ex-posed to high temperatures. If the insula-tion heats up, wires may become

damaged, resulting in a short circuit ormalfunction and permanent damage tothe product.

! Do not cut the GPS antenna cable toshorten it or use an extension to make itlonger. Altering the antenna cable couldresult in a short circuit or malfunction.

! Do not shorten any leads. If you do, theprotection circuit (fuse holder, fuse resis-tor or filter, etc.) may fail to work properly.

! Never feed power to other electronic pro-ducts by cutting the insulation of thepower supply lead of this product and tap-ping into the lead. The current capacity ofthe lead will be exceeded, causing over-heating.

Before installing this product! Use this unit with a 12-volt battery and ne-

gative grounding only. Failure to do so mayresult in a fire or malfunction.

! To avoid shorts in the electrical system, besure to disconnect the (–) battery cable be-fore installation.

<CRD4800-A>4

En4

Section

02 Connection

Black plate (5,1)

To prevent damage

WARNING! Use speakers over 50W (output value)

and between 4W to 8W (impedance value).Do not use 1W to 3W speakers for thisunit.

! The black cable is ground. When instal-ling this unit or power amp (sold sepa-rately), make sure to connect the groundwire first. Ensure that the ground wire isproperly connected to metal parts of thecar’s body. The ground wire of the poweramp and the one of this unit or any otherdevice must be connected to the car sepa-rately with different screws. If the screwfor the ground wire loosens or falls out, itcould result in fire generation of smoke ormalfunction.

Ground wire

Metal parts of car’s body

Power amp

Other devices(Another electronic device in the car)*1Not supplied for this unit.

! When replacing the fuse, be sure to onlyuse a fuse of the rating prescribed on thisproduct.! When disconnecting a connector, pull the

connector itself. Do not pull the lead, asyou may pull it out of the connector.

! This product cannot be installed in a vehi-cle without ACC (accessory) position onthe ignition switch.

ACC ONSTAR

TOFF

ONSTAR

T

OFF

ACC position No ACC position

! To avoid short-circuiting, cover the discon-nected lead with insulating tape. It is espe-cially important to insulate all unusedspeaker leads, which if left uncovered maycause a short circuit.

! Attach the connectors of the same color tothe corresponding colored port, i.e., blueconnector to the blue port, black to black,etc.

! Refer to the owner’s manual for details onconnecting the power amp and other units,then make connections accordingly.

! Since a unique BPTL circuit is employed,do not directly ground the* side of thespeaker lead or connect the * side of an-other side of the speaker lead together. Besure to connect the * side of the speakerlead to the* side of the speaker lead onthis product.

Notice for the blue/white lead! When the ignition switch is turned on (ACC

ON), a control signal is output through theblue/white lead. Connect to an externalpower amp’s system remote control term-inal, the auto-antenna relay control term-inal, or the antenna booster power controlterminal (max. 300mA 12 VDC). The con-trol signal is output through the blue/whitelead, even if the audio source is switchedoff.

! Be sure not to use this lead as the powersupply lead for the external power amps.Such connection could cause excessivecurrent drain and malfunction.

! Be sure not to use this lead as the powersupply lead for the auto-antenna or anten-na booster. Such connection could causeexcessive current drain and malfunction.

<CRD4800-A>5

En 5

English

Section

02Connection

Black plate (6,1)

Parts supplied

This product Power cord

GPS antenna Microphone

Mini-jack extensioncable

USB cable

Lock tie

<CRD4800-A>6

En6

Section

02 Connection

Black plate (7,1)

<CRD4800-A>7

En 7

English

Section

02Connection

Black plate (8,1)

Connecting the power cord (1)

YellowTo terminal supplied with power regardless of ignition switch position.

RedTo electric terminal controlled by ignition switch (12 V DC) ON/OFF.

Orange/whiteTo lighting switch terminal.

Black (ground)To vehicle (metal) body.

With a two-speaker system, do not connect anything to the speaker leads that are not connected to speakers.

When a subwoofer is connected to this product instead of a rear speaker, change the rear output setting in the initial setting. (Refer to Operation Manual.) The subwoofer output of this product is monaural.

Note

Y

ftAc

White Gray

Front speakerFront speaker

White/black Gray/blackLeft Right

Rear speaker or subwoofer (4 Ω)

Rear speaker or subwoofer (4 Ω)

Green Violet

Green/black Violet/black

Green Violet

When using a subwoofer of 70 W (2 Ω), be sure to connect with violet and violet/black leads of this product. Do not connect anything with green and green/black leads.

Green/black Violet/black

Not used. Subwoofer (4 Ω) 2

<CRD4800-A>8

En8

Section

02 Connection

Black plate (9,1)

Audio source will be set to mute or attenuate, while the following sounds will not be muted or attenuated. For details, refer to Operation Manual. — Voice guidance of the navigation— Incoming ring tone and incoming voice of the

cellular phone that is connected to this product via Bluetooth wireless technology

Note

Yellow/black (MUTE)If you use equipment with a mute function, connect that equipment to the Audio Mute lead. If not, keep the Audio Mute lead free of any connections.

Blue/white (SYSTEM REMOTE CONTROL)To auto-antenna relay control terminal or antenna booster power control terminal (max. 300 mA 12 V DC).If the vehicle has a glass antenna, connect to the antenna booster power control terminal (max. 300 mA 12 V DC).

This product

Fuse (10 A)

Power cord

Power supply

<CRD4800-A>9

En 9

English

Section

02Connection

Black plate (10,1)

Connecting the power cord (2)

Violet/white (REVERSE-GEAR SIGNAL INPUT)This is connected so that this product can detect whether the vehicle is moving forwards or backwards. Connect the violet/white lead to the lead whose voltage changes when the shift lever is put in reverse. Unless connected, the sensor may not detect your vehicle traveling forward/backward properly, and thus the position of your vehicle detected by the sensor may be misaligned fromthe actual position.

LIGHT GREEN LEAD AT POWER CONNECTOR IS DESIGNED TO DETECT PARKED STATUS AND MUST BE CONNECTED TO THE POWER SUPPLY SIDE OF THE PARKING BRAKE SWITCH. IMPROPER CONNECTION OR USE OF THIS LEAD MAY VIOLATE APPLICABLE LAW AND MAY RESULT IN SERIOUS INJURY OR DAMAGE.

When you use a rear view camera, please make sure to connect this lead. Otherwise you cannot switch to the rear view camera picture.

Power supply side

Ground side

Parking brake switch

Note

WARNING

Note

This product

Power cordPower supply

Light green (PARKING BRAKE)Used to detect the ON/OFF status of the parking brake. This lead must be connected to the power supply side of the parking brake switch. If this connection is made incorrectlyor omitted, certain functions of this product will be unusable.

The position of the parking brake switch vary depending on the vehicle model. For details, consult your authorized Pioneer dealer or an installation professional.

<CRD4800-A>10

En10

Section

02 Connection

Black plate (11,1)

Connecting the systemThis product

Wired remote inputPlease refer to the instruction manual for the Hard-wired remote control adapter (sold separately).

WARNING· To avoid the risk of accident and the potential violation of applicable laws, this

product should never be used while the vehicle is being driven except for navigation purposes. And, also rear displays should not be in a location where it is a visible distraction to the driver.

· In some countries, the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply they must be obeyed and this product’s video source should not be used.

3.55 m (11 ft. 8 in.)

GPS antenna

Antenna jack

Vehicle antenna

Microphone

4 m (13 ft. 1 in.)

<CRD4800-A>11

En 11

English

Section

02Connection

Black plate (12,1)

Connecting to separately sold power amp

System remote control

Power cord

Blue/white

Power amp(sold separately)

Power amp(sold separately)

Power amp(sold separately)

Front speaker Rear speaker Subwoofer

RCA cables(sold separately)

This product

15 cm (5-7/8 in.)

Rear outputs(REAR OUTPUT)

Front outputs(FRONT OUTPUT)

To system control terminal of the power amp(max. 300 mA 12 V DC).

White, Red (SWL, SWR)

Notes

· You can change the RCA output of the subwoofer depending on your subwoofer system. (Refer to Operation Manual.)

· The subwoofer output of this product is monaural.

Power supply

<CRD4800-A>12

En12

Section

02 Connection

Black plate (13,1)

Connecting an iPhone withLightning connector

Notes

! For details on how to connect an external de-vice using a separately sold cable, refer to themanual for the cable.

! For details concerning the connection, opera-tions and compatibility of iPhone, refer to Op-eration Manual.

Connecting via the USB portThe USB interface cable for iPod / iPhone (CD-IU52) (sold separately) is required for the con-nection.

USB cable1.5 m (4 ft. 11 in.)

USB interface cable for iPod / iPhone(CD-IU52) (sold separately)

This productUSB port 1

iPhone with Lightning connector

USB port 2

Note

Connect the USB cable to USB port 1 when usingApple CarPlay.

Connecting via the HDMI portThe following cables are required for the con-nection.! HDMI interface cable for iPod / iPhone

(CD-IH202) (sold separately)! USB interface cable for iPod / iPhone (CD-

IU52) (sold separately)! Lightning Digital AV Adapter (Apple Inc.

products) (sold separately)

<CRD4800-A>13

En 13

English

Section

02Connection

Black plate (14,1)

USB cable1.5 m (4 ft. 11 in.)

This productUSB port 1

USB interface cable for iPod / iPhone(CD-IU52) (sold separately)

iPhone with Lightning connector

High Speed HDMI® Cable(Type A - A) (supplied with CD-IH202)

HDMI port

Lightning Digital AV Adapter(Apple Inc. products)(sold separately)

Note

! When you connect the High Speed HDMI®

Cable, use the lock tie to fix it securely.= For details, refer to Securing the High

Speed HDMI®Cable on page 17.

Connecting an iPhone with30-pin connector

Notes

! For details on how to connect an external de-vice using a separately sold cable, refer to themanual for the cable.

! For details concerning the connection, opera-tions and compatibility of iPhone, refer to Op-eration Manual.

Connecting via the AUX inputThe USB interface cable for iPod / iPhone (CD-IU201V) (sold separately) is required for theconnection.

This product

USB interface cable for iPod / iPhone(CD-IU201V) (sold separately)

USB cable1.5 m (4 ft. 11 in.)

iPhone with 30-pin connector

AUX input

USB port 1

USB port 2

Mini-jack extension cable2 m (6 ft. 7 in.)

Note

Connect the USB cable to USB port 1 when using“Pandora” as the source.

<CRD4800-A>14

En14

Section

02 Connection

Black plate (15,1)

Connecting via the RGB inputThe USB interface cable for iPod / iPhone (CD-IU201S) (sold separately) is required for theconnection.

USB cable1.5 m (4 ft. 11 in.)

USB interface cable for iPod / iPhone(CD-IU201S) (sold separately)

This productUSB port 1

RGB input

iPhone with 30-pin connector

Connecting the Android™

deviceApp Connectivity Kit (CD-AH200) (sold sepa-rately) is required for the connection.

Notes

! For details on how to connect an external de-vice using a separately sold cable, refer to themanual for the cable.

! For details concerning the connection and op-erations of Android device, refer to OperationManual.

! When you connect the High Speed HDMI®

Cable, use the lock tie to fix it securely.= For details, refer to Securing the High

Speed HDMI®Cable on page 17.

Connecting an Android devicewith an HDMI port

USB cable(supplied with CD-AH200)

This product

Android device

High Speed HDMI® Cable (Type A - A) (supplied with CD-AH200)

USB port 2 HDMI port

USB - micro USB cable(Type USB A - micro USB B)(supplied with CD-AH200)

Adapter cable(HDMI Type A - D)(supplied with CD-AH200)

<CRD4800-A>15

En 15

English

Section

02Connection

Black plate (16,1)

Connecting an Android devicewith an MHL port

USB cable(supplied with CD-AH200)

This product

Android device

USB port 2 HDMI port

High Speed HDMI® Cable(Type A - A) (supplied with CD-AH200)

USB - micro USB cable(Type USB A - micro USB B)(supplied with CD-AH200)

MHL adapter(supplied with CD-AH200)

Connecting the MirrorLink™

deviceThe USB interface cable for use withMirrorLink™ devices (CD-MU200) (sold sepa-rately) is required for the connection.

USB cable(supplied with CD-MU200)

USB - micro USB cable(Type USB A - micro USB B)(supplied with CD-MU200)

This product

MirrorLink device

USB port 2

Note

For details on how to connect an external deviceusing a separately sold cable, refer to the manualfor the cable.

<CRD4800-A>16

En16

Section

02 Connection

Black plate (17,1)

Securing the High SpeedHDMI® CableBe sure to fix the High Speed HDMI® Cablewith the lock tie, when you connect the exter-nal device with the High Speed HDMI® Cable.

1 Insert the High Speed HDMI® Cable intothe HDMI port.

2 Wrap the lock tie around the hookabove the HDMI port and the High SpeedHDMI® Cable, and then tighten it to securethe High Speed HDMI® Cable.

1

2

3

1 Hook2 Lock tie3 High Speed HDMI® Cablep Do not tighten up the lock tie more than

necessary.

<CRD4800-A>17

En 17

English

Section

02Connection

Black plate (18,1)

Connecting a rear view cameraWhen this product is used with a rear viewcamera, it is possible to automatically switchfrom the video to rear view image when theshift lever is moved to REVERSE (R). CameraView mode also allows you to check what isbehind you while driving.

WARNINGUSE INPUT ONLY FOR REVERSE OR MIRRORIMAGE REAR VIEW CAMERA. OTHER USE MAYRESULT IN INJURY OR DAMAGE.

CAUTION! The screen image may appear reversed.! The rear view camera is used as an aid to

keep an eye on trailers, or backing into a tightparking spot. Do not use this function for en-tertainment purposes.

! Objects in rear view may appear closer ormore distant than in reality.

! Please note that the image area shown by therear view camera may differ slightly when full-screen images are displayed when backingand when checking the rear of the vehiclewhile moving forward.

Rear view camera(ND-BC6)

(sold separately)

This product

Brown (BC IN)

RCA cable(supplied with ND-BC6)

Violet/white(REVERSE-GEAR SIGNAL INPUT)

To video output

Power cord

Power supply

For more details about the wiring, refer to Connectingthe power cord (2) on page 10.

Notes

! This mode is available when the rear viewcamera setting is set to “On”. (For details,refer to Operation Manual.)

! Connect this product to the rear view cameraonly. Do not connect to any otherequipment.

<CRD4800-A>18

En18

Section

02 Connection

Black plate (19,1)

Connecting the externalvideo componentUsing AV inputYou can connect an external video componentto this product.

To video outputTo audio outputs

External video component (sold separately)

This product

Red, white (AUDIO INPUT)

RCA cables (sold separately)

Yellow (VIDEO INPUT)

23 cm (9 in.)15 cm (5-7/8 in.)

Note

This mode is available when the setting of AVinput is set to “On”. (For details, refer to Opera-tion Manual.)

Using an AUX input

To video output To audio outputs

External video component (sold separately)

This product

Red, white

RCA cables (sold separately)

Yellow

AUX input

Mini-jack AV cable(CD-RM10)(sold separately)

Mini-jack extension cable2 m (6 ft. 7 in.)

Notes

! This mode is available when the setting ofAUX input is set to “On”. (For details, refer toOperation Manual.)

! When connecting an external video compo-nent using a mini-jack AV cable, use a sepa-rately sold AUX extension cable as necessary.

<CRD4800-A>19

En 19

English

Section

02Connection

Black plate (20,1)

CAUTIONBe sure to use a mini-jack AV cable (CD-RM10)(sold separately) for wiring. If you use othercables, the wiring position might differ resultingin disturbed images and sounds.

OK

GV R

L

GR V

L

L : Left audio (White)R : Right audio (Red)V : Video (Yellow)G : Ground

Connecting an HDMI device

HDMI device(sold separately)

This product

HDMI port

High Speed HDMI® Cable(sold separately)

Notes

! For details concerning the operations of HDMIdevice, refer to Operation Manual.

! When you connect the High Speed HDMI®

Cable, use the lock tie to fix it securely.= For details, refer to Securing the High

Speed HDMI®Cable on page 17.

<CRD4800-A>20

En20

Section

02 Connection

Black plate (21,1)

Connecting the rear display

To video inputTo audio inputs

Rear display with RCA input jacks(sold separately)

RCA cable(sold separately)

Mini pin plug cable(sold separately)

This product

Rear audio output

Yellow (V OUT)

When using a rear displayconnected to rear video output

WARNINGNEVER install the rear display in a locationthat enables the driver to watch the videosource while driving.This product’s rear video output is for connectionof a display to enable passengers in the rearseats to watch the video source.

<CRD4800-A>21

En 21

English

Section

02Connection

Black plate (22,1)

Precautions beforeinstallation

CAUTION! Never install this product in places where,

or in a manner that:— Could injure the driver or passengers if

the vehicle stops suddenly.— May interfere with the driver’s opera-

tion of the vehicle, such as on the floorin front of the driver’s seat, or close tothe steering wheel or shift lever.

! Make sure there is nothing behind thedashboard or paneling when drilling holesin them. Be careful not to damage fuellines, brake lines, electronic components,communication wires or power cables.

! When using screws, do not allow them tocome into contact with any electrical lead.Vibration may damage wires or insulation,leading to a short circuit or other damageto the vehicle.

! To ensure proper installation, be sure touse the supplied parts in the manner spe-cified. If any parts are not supplied withthis product, use compatible parts in themanner specified after you have the parts’compatibility checked by your dealer. Ifparts other than supplied or compatibleones are used, they may damage internalparts of this product or they may workloose and the product may become de-tached.

! It is extremely dangerous to allow cablesto become wound around the steering col-umn or shift lever. Be sure to install thisproduct, its cables, and wiring away insuch so that they will not obstruct or hin-der driving.

! Make sure that leads cannot get caught ina door or the sliding mechanism of a seat,resulting in a short circuit.

! Please confirm the proper function ofyour vehicle’s other equipment after in-stallation of this product.

! Do not install this product where it may (i)obstruct the driver’s vision, (ii) impair theperformance of any of the vehicle’s oper-ating systems or safety features, includ-ing airbags, hazard lamp buttons or (iii)impair the driver’s ability to safely oper-ate the vehicle.

! Install this product between the driver’sseat and front passenger seat so that itwill not be hit by the driver or passenger ifthe vehicle stops quickly.

! Never install this product in front of ornext to the place in the dashboard, door,or pillar from which one of your vehicle’sairbags would deploy. Please refer to yourvehicle’s owner’s manual for reference tothe deployment area of the frontal air-bags.

! Failure to follow all of these precautionsmay result in serious injury or death.

To avoid electromagneticinterferenceIn order to prevent interference, set the follow-ing items as far as possible from this product,other cables or leads:! FM, AM antenna and its lead! GPS antenna and its leadIn addition, you should lay or route each an-tenna lead as far as possible from other anten-na leads. Do not bind, lay or route themtogether, or cross them. Electromagneticnoise will increase the potential for errors inthe vehicle’s location display.

Before installing! Consult with your nearest dealer if installa-

tion requires drilling holes or other modifi-cations of the vehicle.

! Before making a final installation of thisproduct, temporarily connect the wiring toconfirm that the connections are correctand the system works properly.

<CRD4800-A>22

En22

Section

03 Installation

Black plate (23,1)

Installing this productInstallation notes! Do not install this product in places subject

to high temperatures or humidity, such as:— Places close to a heater, vent or air con-

ditioner.— Places exposed to direct sunlight, such

as on top of the dashboard.— Places that may be exposed to rain,

such as close to the door or on the vehi-cle’s floor.

! Install this product in an area strong en-ough to bear its weight. Choose a positionwhere this product can be firmly installed,and install it securely. If this product is notsecurely installed, the current location ofthe vehicle cannot be displayed correctly.

! Install this product horizontally on a sur-face within 0 to 30 degrees tolerance (with-in 5 degrees to the left or right). Improperinstallation of the unit with the surfacetilted more than these tolerances increasesthe potential for errors in the vehicle’s loca-tion display, and might otherwise cause re-duced display performance.

30°

5° 5°

! When installing, to ensure proper heat dis-persal when using this unit, make sure youleave ample space behind the rear paneland wrap any loose cables so they are notblocking the vents.

Leave ample space 5 cm

5 cm

! The cords must not cover the area shownin the figure below. This is necessary toallow the amps to dissipate heat.

Do not cover this area.

! Do not squeeze this product into the holder.It may damage the front panel.

<CRD4800-A>23

En 23

English

Section

03Installation

Black plate (24,1)

Parts supplied

This product Truss head screw(5 mm × 8 mm)

(6 pcs.)

Flush surface screw(5 mm × 9 mm)

(6 pcs.)

Installation using the screwholes on the side of this product% Fastening this product to the factoryradio-mounting bracket.Position this product so that its screw holesare aligned with the screw holes of the brack-et, and tighten the screws at three locationson each side.Use either the truss head screws (5mm ×8mm) or flush surface screws (5mm ×9mm), depending on the shape of the brack-et’s screw holes.

If the pawl interferes with installation, you may bend it down out of the way.

1

2

3

1 Factory radio-mounting bracket2 Dashboard or console3 Truss head screw or flush surface screw

Be sure to use the screws supplied withthis product.

<CRD4800-A>24

En24

Section

03 Installation

Black plate (25,1)

Installing the GPS antenna

CAUTIONDo not cut the GPS antenna lead to shortenit or use an extension to make it longer. Alter-ing the antenna cable could result in a shortcircuit or malfunction and permanent da-mage to this product.

Installation notes! The antenna should be installed on a level

surface where radio waves will be blockedas little as possible. Radio waves cannot bereceived by the antenna if reception fromthe satellite is blocked.

1 2

1 Dashboard2 Rear shelf

! When installing the GPS antenna insidethe vehicle, be sure to use the metal sheetprovided with your system. If this is notused, the reception sensitivity will be poor.

! Do not cut the accessory metal sheet. Thiswould reduce the sensitivity of the GPS an-tenna.

! Take care not to pull the antenna lead whenremoving the GPS antenna. The lead maybecome detached.

! Do not paint the GPS antenna, as this mayaffect its performance.

Parts supplied

GPS antenna Metal sheet

Clamp (3 pcs.) Double-sided tape

<CRD4800-A>25

En 25

English

Section

03Installation

Black plate (26,1)

When installing the antenna inside the vehicle (on the dashboardor rear shelf)

WARNINGDo not install the GPS antenna over any sen-sors or vents on the dashboard of the vehicle,as doing so may interfere with the properfunctioning of such sensors or vents and maycompromise the ability of the metal sheetunder the GPS antenna to properly and se-curely affix to the dashboard.

The metal sheet contains a strong adhesive which may leave a mark on the surface if it is removed.

Note

Make sure the surface is free of moisture, dust, grime, oil, etc., before affixing the metal sheet.

1 2

3

1 GPS antenna2 Metal sheet

Peel off the protective sheet on the rear.3 Clamps

Use clamps to secure the lead where neces-sary inside the vehicle.

Affix the metal sheet on the surface as level aspossible where the GPS antenna faces thewindow. Affix the GPS antenna on the metalsheet using the double-sided tape.

Notes

! When attaching the metal sheet, do not cutit into small pieces.

! Some models use window glass that doesnot allow signals from GPS satellites topass through. On such models, install theGPS antenna on the outside of the vehicle.

<CRD4800-A>26

En26

Section

03 Installation

Black plate (27,1)

Installing the microphone! Install the microphone in a place where its

direction and distance from the drivermake it easiest to pick up the driver’s voice.

! Be sure to turn off (ACC OFF) the productbefore connecting the microphone.

Parts supplied

Microphone Double-sided tape

Mounting on the sun visor1 Fit the microphone lead into thegroove.

1

2

1 Microphone lead2 Groove

2 Attach the microphone clip to the sunvisor.

1

2

1 Microphone clip2 Clamps

Use separately sold clamps to secure thelead where necessary inside the vehicle.

Install the microphone on the sun visor whenit is in the up position. It cannot recognize thedriver’s voice if the sun visor is in the down po-sition.

<CRD4800-A>27

En 27

English

Section

03Installation

Black plate (28,1)

Installation on the steering column1 Detach the microphone base from themicrophone clip by sliding the microphonebase while pressing the tab.

4

1

2

3

1 Microphone2 Tab3 Microphone base4 Microphone clip

2 Mount the microphone on the steeringcolumn.Install the microphone on the steering col-umn, keeping it away from the steering wheel.

1

2

1 Double-sided tape2 Clamps

Use separately sold clamps to secure thelead where necessary inside the vehicle.

Adjusting the microphone angleThe microphone angle can be adjusted.

<CRD4800-A>28

En28

Section

03 Installation

Black plate (29,1)

After installing this product1 Reconnect the negative (–) terminal ofthe vehicle’s battery.First, double-check that all connections arecorrect and that this product is installed cor-rectly. Reassemble all vehicle componentsthat you previously removed. Then reconnectthe negative (–) cable to the negative (–) term-inal of the battery.

2 Start the engine.

3 Change the settings as desired.= For details concerning operations, refer to

Operation Manual.

4 Drive down an unobstructed road untilthe GPS starts receiving the signal nor-mally.

Note

After installing this product, be sure to check at asafe place that the vehicle is performing normal-ly.

<CRD4800-A>29

English

Section

04After installation

Shop the largest selection of reliable car stereos in our online store.