Performa Tv Card

8/2/2019 Performa Tv Card

1/14

2 TV/Video Upgrade Kit

Purpose: This document describes the installationprocedure of an upgrade package for someMacintosh models. The upgrade consists of thevideo input card, a TV tuner card, and an external

video connector. These components provide thecapability to view videotapes and TV broadcastson the computer.

Parts: The parts you need to install the TV/video systemare obtained from the kit for the Apple TV/VideoSystem (part no. 602-1173-A). These are: video input card

TV tuner card attachment screws video software installer diskettes

Video input card

TV tuner card

Attachment screws


2/14

TV/Video Upgrade Kit 3

If your computer did not come with the externalvideo connector, you can get this part from thekit for the Apple External Video System(part no. 5). This system includes:

external video connector metal bracket 2 jacknuts

Tools: small Phillips screwdriverpair of pliers

Special Procedures: The boards are sensitive to damage fromelectrostatic discharge (ESD). Follow ESDprotocols. Do not unwrap the boards until youare ready to install them. Handle the boards onlyby the edges.

External video connector

Jacknuts

Metal bracket


3/14


1. Remove:all cables from

the rear of thecomputer exceptthe power cord.

the 2 retainerscrews.

the rear panel by

pulling gently onthe latch keys

under the case.

2. Pull down the wire

handle on the rearof the logic board.

Use the handle toslide the logicboard out of thecomputer.

Rear panel

Installing the TV Tuner Card

Wire handle attached to

logic board


4/14


3. Locate the ribboncable under the

logic board tray,and attach it to theconnector on theTV tuner card.

4. Slide the TV tuner

card into thechannel under the

logic board tray.Check that thenotches point up.

Connector Ribbon cable plug

TV tuner card

Install the TV tuner card with these

notches pointing upward.


5/14


5. Install anattachment screw

to secure the TVtuner card.

6. Punch out the plug

on the rear panelto clear the port

access hole for theTV tuner.

N014_0007Plug


6/14


7. Remove the plastic

access cover.Compress the tabsand pull it fromthe metal retainer.

8. Remove the metalretainer.

Installing the External Video Connector

N014_0009AC

If the external video connector is installed, advance to step 13.

Plastic access cover

Metal retainer


7/14


9. Insert the newmetal bracket.Check that thebracket engagesthe two hooks.

10. Connect the smallcard on the end of

the external video

connector to themonitor-out sloton the logicboard.

11. Attach the videoconnector to the

metal bracket andsecure it with twojacknuts.

N014_0010AC

Jacknut

External video connector

Metal bracket

The metal bracket is correctly seated when it

engages these two hooks.


8/14

Video input cover


13. Remove the videoinput cover fromthe rear plate of

the logic board toclear the port

access hole.

12. Attach the plasticaccess cover.

Check that thevideo connectorprotrudesthrough theopening.

Installing the Video Input Card

Plastic access cover

Logic board (removed in step 2)


9/14


14. Connect the videoinput card to the

logic board.

15. Secure the video

card to the rearplate using a self-

tapping screw. Donot over-tighten.

N014_00

Logic board

Video input card


10/14


Reset button

16. Insert the logicboard into thechannel but donot yet install it allthe way.

17. Press the red reset

button beforesliding the logicboard back intothe computer.

18. Swing the wire

handle up to thestorage position.

Wire handle attached to

logic board


11/14


19. Install the rear panel and the retainer screws.

20. Start the computer.

21. Check the date and time. If necessary, open the Control Panels toset the current date and time.

22. Insert the Video Software Controller diskette.

23. Launch the Installer application on the diskette.

24. When the Installer is completed, restart the computer.

25. Keep the remaining materials from the installation kits (remotecontrol, software diskettes, publications).

Completing the Installation


12/14

Installation Instructions

Apple

TV/Video Upgrade Kitfor the

Power Macintosh/Performa

5200 series and 5300 series


13/14

Apple Computer, Inc.

1996 Apple Computer, Inc. All rights reserved.

Under the copyright laws, this manual may not be copied, in whole or in part, without the

written consent of Apple. Your rights to the software are governed by the accompanying

software license agreement.

The Apple logo is a trademark of Apple Computer, Inc., registered in the U.S. and othercountries. Use of the keyboard Apple logo (Option-Shift-K) for commercial purposes

without the written consent of Apple may constitute trademark infringement and unfaircompetition in violation of federal and state laws.

Every effort has been made to ensure that the information in this manual is accurate. Appleis not responsible for printing or clerical errors.

Apple Computer, Inc.

1 Infinite LoopCupertino, CA 95014-2084

(408) 996-1010Apple, the Apple logo, Performa, and Power Macintosh are trademarks of Apple Computer,

Inc., registered in the U.S. and other countries.

Published in the U.S.


14/14


C O N T E N T S

Purpose..................................................................................2Parts.......................................................................................2Tools ......................................................................................3Special Procedures ................................................................3Installing the TV Tuner Card.................................................4Installing the External Video Connector...............................7Installing the Video Input Card.............................................9Completing the Installation................................................12

Performa Tv Card

Documents

Transcript of Performa Tv Card