Optical Sensor Product Guide-Lr

8/13/2019 Optical Sensor Product Guide-Lr

1/60

Optoisolation and Optical Sensor Products

Selection Catalog

Your Imagination, Our Innovation

Sense Illuminate Connect


2/60

Optoisolation Products

9 Multi-Channel & Bi-Directional Digital Optocoupler

10 High Speed Digital CMOS Logic Gate Optocoupler

12 20 MBd Logic Gate Optocoupler

13 10 MBd Logic Gate/CMOS Optocoupler16 8 MBd Logic Gate Optocoupler

17 5 MBd Logic Gate Optocoupler

18 1 MBd Transistor Output Optocoupler

19 100 kBd Darlington Transistor Output Optocoupler

20 R2Coupler (High Temperature, Automotive Grade)

24 Digital Isolator

25 Miniature Analog Isolation Amplifier

27 Integrated Gate Drive Optocoupler

30 Intelligent Power Module Interface Optocoupler

32 Isolated Line Receiver

33 Isolated 20 mA Current Loop Transmitter/Receiver

34 Isolated Voltage/Current Detector

35 High Linearity Analog Optocoupler

36 Wideband Analog/Video Optocoupler

37 General Purpose Phototransistor Optocoupler

39 Solid State Relay (Photo MOSFET)

42 Powerline Communication Interface

43 Hermetic High Performance Optocoupler

47 Package Drawings

57 Function vs Application Matrix

Optical Sensors

59 Proximity and Ambient Light Sensors


3/60

3

Avago Technologies offers the

industrys best isolation technologyalong with the industrys leading

CMR performance

Avago Technologies optocouplers can be used in an array of isolation applications ranging

from power supply and motor control circuits to data communications and digital logicinterface circuits.

The primary purpose of an optocoupler is to provide both electrical insulation and signal

isolation. The popularity of Avago Technologies optocouplers is due to cost effectiveinnovations in these areas.

Optocouplers eliminate the effects of electrical noise caused by crosstalk, power glitches andelectrical interference. They provide high voltage isolation allowing safe interface between

high and low voltages in electrical circuits. They are also used for shifting logic levels.Avago Technologies key products include optocouplers with phototransistor output,

digital and analog output, high speed and high gain performance, drivers for isolatedgate transistors and intelligent power modules, smart current sensors, solid state relay

(Photo MOSFET) and other application specific devices.

Avago Technologies offers the industrys best isolation technology along with the industrys

leading CMR performance of up to 40 kV/s in a broad line of packages. Products include

the lowest power dissipation with input current as low as 40 A, high speed digitaloptocouplers operating at up to 50 MBd, propagation delays as low as 22 ns, 3.3 V JEDECcompatible optocouplers. Avago Technologies optocouplers are manufactured with high

quality and reliability and have worldwide safety approvals including the highest maximuminsulation voltage (VIORM) at 2262 V (per IEC/EN/DIN EN 60747-5-2/5).


4/60

4

Avago Technologies offers a broad range of isolation products

that provide performance features and benefits that are

unmatched in the industry for industrial, computing, consumer,communication, medical, military and aerospace markets.

Applications for Avago Technologies Isolation Products

Industrial

The widest portfolio of

optocouplers to meet theextensive requirements

of applications in factoryautomation.

Automated test equipment

Battery operated vehicle

Fieldbus

Industrial communications

Industrial networking

Motor control

PLC input/output isolation

Power distribution systems

Power generation

Renewable energy power

generation

Robotics

Switching panel

Switching power supplies

Test and measurementequipment

Automotive

Avago Technologiesautomotive R2Coupler areAEC-Q100 qualified with

applications in:

Automotive andshipboard system CANBusinterface isolation

Motor inverter drives

DC-DC converters/inverters for batterychargers

Battery/inverter voltagemonitoring

Status/fault signal feedbackisolation interface

Heating, ventilation andair-conditioning

Medical

Avago Technologiesoffers optocouplers with

high linearity and high

resolution for severeisolation requirements to:

Debrillators

ECG/EKG

Endoscopes

Magnetic resonanceimaging

Patient monitoring

Computers and OfficeEquipment

Avago Technologies

optocouplers with CMOScompatibility and high

speed are used to provideinterface isolation for:

Isolated input/outputmodule

Isolated USB hub

Printers and plotters

Communications

Avago Technologiesprovides high speed

optocouplers in both singleand dual surface-mount

packages which are used in:

Automated meteringreading

Digital cross connect

Distributed powerarchitecture

ISDN

Modems

PBX and central oce

Power linecommunication

Power over ethernet

Telephone switchingequipment

Telephone terminalequipment

Wireless base station

Consumer Electronics

Avago Technologiesoffers lower solution costswith highly integrated

optocouplers for manyconsumer applications,

such as:

Air conditioning

Alarm systems Audio and video

equipment

Electronic gaming

Fitness equipment

Induction cookers

Plasma displays

Washing machines

Military and Aerospace

Avago Technologies highreliability optocouplers are

suitable for military andaerospace applications

such as:

Aircraft, satellite and spacesystems

Communications

Computers

Test systems

Defense systems

Avago, Avago Technologes, the A logo, R 2Coupler are trademarks of Avago Technologies in the United States and other countries.


5/60

5

Upgrade Part Feature Benefit

High Voltage Insulation

Improved Isolation/Insulation

Ability to protect surrounding circuitry against physicaldamages resulting from differential voltages.

ACNV family offers highest available working voltageratingswith regulatory approval per IEC/EN/DIN EN 60747-5-2/5 of2262 V peak.

Meets international safety regulations and standards.Provides better isolationand overall safetyperformance.

Noise Isolation

High CMR

Common-mode transient rejection or signal isolation of datathrough suppression of noise transients.

Offers guaranteed CMR performance up to 40 kV/swhich isthe highest available in the market.

Improves system performance, and reliability.More robustsystems and better data integritymeet EMI and ESDrequirements.

Power Consumption

Drive Current, IF

Low Drive Current, LED drive current.

Offers the lowest IF(as low as 40 A)devices in the marketand broadest HCMOS compatibility.

Eliminates additional LED drive circuitry. Improvessystem efficiency and reduces power consumption and LEDdegradation.

Lower Power Supply

Lower power supply (3.3V)

Lower the power consumptionand meets JEDEC low voltagerequirements.

Up to 50%energy saving.

Flexible Supply Voltages(3.3V/5V)

Support a combination of two different supply voltages at theinput and output.

Built-in internal level shifter,eliminate the need of extrapower supply. 3.3V or 5V.3.3V helps to improve the overall power consumption.

Temperature

Temperature

The DC, speed performance and the reliability information isensured at the specific temperature range.

Support up to -40C to 125Ct emperature range. Allow extreme temperature operation.

Speed Benefits

Propagation Delay, tpDescribes how quickly a logic signal can propagate throughthe system.

High speed digital optocouplers to meet wide range ofapplications with tp as low as 22 ns. Increase switching efficiencyand better speed performance.

Upgrade Pulse Width Distortion, PWD

PWD is the difference between tPHLand tPHLand oftendetermines the maximum data rate capability of atransmission system.

The lowest PWD offered by optocoupler is2 ns. To ensure signal data integrityover long bus line.

Package and Space Savings

Multi-Channels,Bi-directional Features

Integrateddual, triple, quadwith bi-directionalchannelsoffers in small SO8 and SO16 package.

The integrated bi-directional channels help in space savingsand ease of designs.

Surface Mount Device

SMD permits more component density than DIP.

Smaller package to deliver the same functionalityas standard DIP.

True surface mount technology and standard footprint.

Lower assembly cost,easier and faster handling as well asbetter solderability.

8mm Clearance/Creepage (C/C) Packages The package is 50% smaller than conventional DIP package.It can withstand high isolation voltages and meet regulatoryrequirements such as IEC/UL/CSA standards.

Provides space savings.Allows high voltage surgeprotection. Meets many IEC/UL/CSA equipment standardsthat call for clearance and creepage of 8mm.

Smaller SO5 Package Smaller SO5package (as compared to existing SO-8 package) Provides greater than 40% space savings.

Quick Guide to Direct Upgrades


6/60

6

Existing Parts Upgrade Parts Upgrade Features Footprint Information

High Speed Family (>12.5MBd)

HCPL-0708 ACPL-071L Flexible supply voltages (3.3V/5V) Lower Propagation Delay (


7/60


8/60

8

Existing Parts Upgrade Parts Upgrade Features Footprint Information

Intelligent Power Module Interface Optocoupler

HCPL-4502HCPL-4503

ACPL-K453 8mm Creepage and Clearance 50% smaller package size

Smaller footprint

HCPL-4504 ACPL-W454 8mm Creepage and Clearance 50% smaller package size

Smaller footprint

ACPL-P454 8mm Creepage 50% smaller package size

Smaller footprint

HCPL-4506 ACPL-W456 8mm Creepage and Clearance 50% smaller package size

Smaller footprint

ACPL-P456 8mm Creepage 50% smaller package size

Smaller footprint

ACPL-4800 ACPL-W480 8mm Creepage and Clearance 50% smaller package size

Smaller footprint

ACPL-P480 8mm Creepage

50% smaller package size

Smaller footprint

HCPL-M452/3/4/6 ACPL-M484 Higher CMR 30kV/s 10MBd speed Totem-pole output, positive logic

Faster speed

HCPL-4502/03/04/06HCPL-0452/53/54/66

ACPL-W484 8mm Creepage and Clearance Higher CMR 30kV/s 10MBd speed Totem-pole output, positive logic

Faster speed

HCNW4502/03/04/06 ACNV4506 13mm Creepage and Clearance Higher Working Voltage Viorm 2262Vpk Higher CMR 30kV/s Totem-pole output, positive logic

Higher Working Voltage

HCPL-M452/53/54 ACPL-M43U Wide temperature (-40C to 125C)

Low LED input drive current IF 10mA

Drop-in replacement

HCPL-M456 ACPL-M46U Wide temperature (-40C to 125C) Drop-in replacement

General Purpose Phototransistor Optocoupler

HCPL-817 ACPL-827ACPL-847

Multi-channel. 2-ch and 4-ch Higher Integrations

HCPL-814 ACPL-824ACPL-844

Multi-channel. 2-ch and 4-ch Higher Integrations

HCPL-181/817 ACPL-217 Smaller package (SO4 half-pitch) CMR 10kV/s (typ) Extended Industrial -55 to 110C Viso 3kVrms (1min)

Smaller footprint

HCPL-354/814 ACPL-214 Smaller package (SO4 half-pitch)

CMR 10kV/s (typ) Extended Industrial -55 to 110C Viso 3kVrms (1min)

Smaller footprint

Note:

Drop-in replacementmeans no PCB board redesign is required,

Pin-to-Pinmeans the footprint is same but requires minimum PCB board redesign (eg. Removing of external resistor)

* Lower speed

^ Advanced information, may subject to changes.


9/60


10/60

10


High Speed Digital CMOS Logic Gate Optocoupler

DescriptionThese optocouplers use the latest CMOS IC

technology to achieve outstanding perfor-mance with very low power consumption.

Serial fieldbuses are used today primarily asthe communication system for the exchangeof information between automation system

and distributed eld devices. PROFIBUS is

the leading open fieldbus system and it has

worldwide acceptance. PROFIBUS is es-sentially a twisted wire pair serial link that

is very similar to RS 485. Profibus speed

standard is either lower speed (1.5 MBd) orhigher speed (12 MBd).

In this isolated multipoint transmissionapplication circuit, two different optoisolators

are utilized (HCPL-0721 and HCPL-061N).The benefits include low input drive current

that maximizes LED lifetime/reliability andoptimizes speed for Profibus and RS-485

applications.

Benefits High speed (up to 50 MBd)

3.3V/5V dual supply voltage available

Wide temperature operation -40C to100C (HCPL-x710)

Low PWD (2ns) & low tp (22ns) to meetDeviceNet and Profibus application

Buer input and CMOS output toeliminate any pull-up resistor

5 kV isolation voltage (HCPL-77xx)

Dual channel device is available to

save space(HCPL-0738) Certied with reinforced insulation

under IEC/EN/DIN EN 60747-5-2

Applications

AC plasma displaypanel level shifting

CAN Bus

CC_Link

Microprocessor

system interface Mutiplexed data

transmission

Switchingpower supply

X

X

X

CC

T

5V ISO 5V

7

1

2

3

4

6

5SHIELD

ACPL-072L

0.01

0.01F

R

1

5V ISO 5V

8

8

7

6

5

3

4

SHIELD

ACPL-072L

0.01

0.01

T

1

2

2

8

7

6

5

3

4

SHIELD

ACPL-061L^

TENABLE

5V

ISO 5V

0.01

680

1M

ISO 5V

REG

0.01

+6

75ALS176D

8

R

7

A

R

D

DE

RE

B

0.01

GND

V1

4

3

2

5

ISO 5V

F

F

F

F

F

F

Typical Profibus Block Diagram


11/60

11


High Speed Digital CMOS Logic Gate Optocoupler Product Selection

Device Part No. Package VDDV

IF(on)mA

Min.

Max DataRate MBd

Min.

tPLHns

Max.

tPHLns

Max.

PWDns

Max.

tPSKns

Max.

CMR - V/s@VCM VISOVRMS

Min.

VIORMV

peakCMRV/s (Min.)

VCMV

Single Channel CMOS Input HCPL-0710 SO8 5 12.5 40 40 8 20 10000 1000 3750 560*

HCPL-0720 SO8 5 25 40 40 8 20 10000 1000 3750 560*

HCPL-0721 SO8 5 25 40 40 6 20 10000 1000 3750 560*

HCPL-0723 SO8 5 50 22 22 2 16 10000 1000 3750 560*

HCPL-7710 300 mil DIP8 5 12.5 40 40 8 20 10000 1000 3750/5000# 630*

HCPL-7721 300 mil DIP8 5 25 40 40 6 20 10000 1000 3750/5000# 630*

HCPL-7720 300 mil DIP8 5 25 40 40 8 20 10000 1000 3750/5000# 630*

HCPL-7723 300 mil DIP8 5 50 22 22 2 16 10000 1000 3750/5000# 630*

LED Input HCPL-0708 SO8 5 10 15 60 60 30 40 10000 1000 3750 560*

Dual Channel LED Input HCPL-0738 SO8 5 10 15 60 60 30 40 10000 1000 3750 560*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL5000VRMS /1 minute Option 020

1

SHIELD

D1

V1

GND1

D

VO

GND

NC

IOED1

VDD

NC

VO

GND

NC 1

2

3

4

8

7

6

5

ANODE

CATHODE

NC

VDD2

VO2

VO1

GND

1

2

3

4

8

7

6

5

ANODE1

ANODE2

CATHODE2

CATHODE1

3.3V/5V Family (15/25 MBd High Speed Digital CMOS Optocoupler)


IF(on)mAMin.

Max.Data RateMBd Min.

tPLHnsMax.

tPHLnsMax.

PWDnsMax.

tPSKnsMax.

CMR - V/s@VCM VISOVRMSMin.

VIORMVpeakCMR

V/s (Min.)VCMV

Single Channel CMOS Input ACPL-072L-000E SO8 3.3/5 25 40 40 6 20 10000 1000 3750 560*

ACPL-772L-000E 300 milDIP8

3.3/5 25 40 40 6 20 10000 1000 3750/5000 #

630*

Single Channel LED Input ACPL-071L-000E SO8 3.3/5 10 15 40 40 25 30 10000 1000 3750 560*

ACPL-W70L-000E StretchedSO6

3.3/5 4 15 55 55 25 40 10000 1000 5000 1140*

ACPL-M75L-000E SO5 3.3/5 4 15 55 55 25 40 10000 1000 3750 560*

Dual Channel LED Input ACPL-074L-000E SO8 3.3/5 10 15 40 40 25 30 10000 1000 3750 560*

ACPL-K73L-000E StretchedSO8

3.3/5 4 15 55 55 25 40 10000 1000 5000 1140*

Notes: * - with IEC/EN/DIN EN 60747-5-2 Option 060, #- with UL 5000V RMS /1 minute Option 020.

8

7

63

HIELD5

2

4

V D1

V1

ND1

VDD2

VO

GND2

NC

OLED1

VO

VDD

GND

1

2

3

5

ANODE

CATHODE

4

VDD

NC

VO

GND

NC 1

2

3

4

8

7

6

5

ANODE

CATHODE

NC

VO

VDD

GND

1

2

3

6

5

4

ANODE

NC*

CATHODE

VDD2

VO2

VO1

GND

1

2

3

4

8

7

6

5

ANODE1

ANODE2

CATHODE2

CATHODE1

VO1

VDD

GND

1

2

3

8

7

5

ANODE 1

CATHODE 1

CATHODE 2

4ANODE 2

VO26

NEW

NEW

NEW

NEW

NEW

NEW

NEW


12/60


13/60

13


DescriptionThis isolated RS-422 circuit uses two

high-speed optocouplers that can switchup to 10 MBd signals. An isolated pow-

er supply VCC2 is required to power theDS 75176A driver/receiver integrated circuit.

The main benef it i s preventing common-mode transients from interfering with thesignal.

Avagos new range of 3.3 V/5 V optocouplersare the first commercially available optocou-plers designed to meet the JEDEC specifica-tion for 3.3 V LVTTL/LVCMOS logic, therebysimplifying the implementation of isolationin systems utilizing 3.3 V logic circuits.

A typical Power over Ethernet powersource equipment (PSE) block diagram usestwo 15 MBd 3.3 V optocouplers to isolatebetween the 13 W 48 V power supply and

the inter-integrated chip (I2C) control bus.

Benefits

Provides high data rate transmission. Italso offer high CMR for signal isolationfrom common mode transient noises

Applications

Computer-peripheralinterface

Instrument input/outputisolation

Isolated line receiver

Microprocessor systeminterface

Switching power supply

Typical RS-422 Interface Block Diagram

10 MBd Logic Gate/ CMOS Optocoupler

Typical Power over Ethernet Power Source Block Diagram


14/60


15/60

15


3.3V/5V Family (10 MBd CMOS Optocoupler)


IF(on)mA

Min.

Max.Data Rate

MBd Min.

tPLHns

Max.

tPHLns

Max.

PWDns

Max.

tPSKns

Max.


Min.

VIORMV

peakCMRV/s (Min.)

VCM

V

Single Channel LED Input ACPL-061L-000E^ SO8 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*

ACPL-C61L-000E^ StretchedSO8

3.3/5 2.5 10 110 110 40 40 20000 1000 3750 1140*

ACNW261L-000E^ 400 mil DIP 3.3/5 2.5 10 120 120 50 40 20000 1000 3750 1414*

ACPL-W61L-000E StretchedSO6

3.3/5 1.6 10 80 80 30 30 20000 1000 5000 1140*

ACPL-M61L-000E SO5 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*

ACPL-M62L-000E ^ SO5 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*

Dual Channel LED Input ACPL-064L-000E SO8 3.3/5 1.6 10 80 80 30 30 20000 1000 3750 560*

ACPL-K64L-000E StretchedSO8

3.3/5 1.6 10 80 80 30 30 20000 1000 5000 1140*

Notes: * - with IEC/EN/DIN EN 60747-5-2 Option 060, #- with UL 5000V RMS /1 minute Option 020, ^ - Advanced Information, may subject to changes.

VO

VDD

GND

1

2

3

5

ANODE

CATHODE

4

VO

VDD

GND

1

3

4

6

ANODE

CATHODE

5

VO

VDD

GND

1

2

3

5

ANODE

CATHODE

4

VDD

VE

VO

GND

NC 1

2

3

4

8

7

6

5

ANODE

CATHODE

NC

VDD

VE

VO

GND

NC 1

2

3

4

8

7

6

5

ANODE

CATHODE

NCSHIELD

VDD2

VO2

VO

GND

1

2

4

6

5

ANODE1

ANODE2

CATHODE1

V D 2

O

VO

GND

1

2

3

4

6

5

ANODE1

ANODE2

CATHODE2

CATHODE1

NEW

NEW

NEW

NEW

NEW


16/60

16


DescriptionThe circuit shows a CMOS interface circuit

for 8 MBd applications. Over the tempera-ture range a CMOS CD4050 Hex Buffer

can source about 0.7 mA (minimum), whichis sucient to drive the HCPL-2300 opto-coupler. The 20 pF capacitor allows peaking

currents to assist the LED in turning on andoff quickly.

These optocouplers utilize a simple interfacerequiring low power consumption.

Benefits Oers low power consumption

8 MBd Logic Gate Optocoupler Product Selection

Device Part No. Package IF(on)mAMin.

tPLHsMax.

tPHLsMax.


VIORMVpeakCMR V/s (Min.) VCM

V

Single Channel HCPL-0300 SO8 0.5 0.16 0.2 100 50 3750

HCPL-2300 300 mil DIP8 0.5 0.16 0.2 100 50 3750 630*

Notes:

* - with IEC/EN/DIN EN 60747-5-2/5 Option 060

1

4

8

7

6

5

VCC

VD

RL

GND

2

3

Anode

Cathode

Applications


Digital isolation forA/D, D/A conversion

High speed, long

distance isolatedline receiver

Level shifting

RS 232C interface

Typical CMOS Interface Block Diagram

8 MBd Logic Gate Optocoupler


17/60

17


DC Bus

ontrol

Circuit

PWM

Controller

Gate

Driver

Power

Switch

Digital

Optocoupler

Output(AC-DC)

DC Output

Output

Recti er

Trans ormer

DescriptionThe circuit shown in the typical TTL interface

block diagram is an interface between twoTTL gates using an active output (totem

pole) optocoupler, the HCPL-2201. A seriesswitching circuit drives the optocouplerLED. The active output HCPL-2201 can be

directly connected to a TTL gate, and nopull-up resistor is required. The HCPL-2201

can sink enough current to handle up to16 LSTTL or 4 TTL loads.

Typically, the 5 MBd logic gate optocoupler

is used in the Isolated High-Low Gate Driveinterface block diagram as shown below.

Benefits Pull up resistor not required at the

optocoupler output

Low power on the optocoupler inputcircuit

Wide operating supply voltagesup to 20V

Built-in Schmitt Triggers for better signalintegrity and accuracy in a noisy network/circuits.

5 MBd Logic Gate Optocoupler Product Selection

Device Part No. Package IF(on)mAMin.

tPLHsMax.

tPHLsMax.


VIORMVpeakCMR V/s (Min.) VCM

V

Single Channel HCNW2201 400 mil DIP8 1.6 0.3 0.3 1000 50 5000 1414HCNW2211 400 mil DIP8 1.6 0.3 0.3 10000 1000 5000 1414HCPL-0201 SO8 1.6 0.3 0.3 1000 50 3750 560*HCPL-0211 SO8 1.6 0.3 0.3 10000 1000 3750 560*HCPL-2219 300 mil DIP8 1.6 0.3 0.3 2500 400 3750 630*

HCPL-2200 300 mil DIP8 1.6 0.3 0.3 1000 50 3750 630*HCPL-2201 300 mil DIP8 1.6 0.3 0.3 1000 50 3750 630*HCPL-2211 300 mil DIP8 1.6 0.3 0.3 10000 1000 3750 630*HCPL-2202 300 mil DIP8 1.6 0.3 0.3 1000 50 3750 630*

HCPL-2212 300 mil DIP8 1.6 0.3 0.3 10000 1000 3750 630*

Dual Channel HCPL-2231 300 mil DIP8 1.8 0.3 0.3 1000 50 3750

HCPL-2232 300 mil DIP8 1.8 0.3 0.3 10000 1000 3750

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060

7

1

2

3

4 5

6

8NC

ANOD

ATHODE

NC ND

V C

O

HIELD

ANODE

ATHOD

NC ND

V C

1

2

3

4 5

8ANODE

ANODE 2 GND

VCC

VO1

VO2

SHIELD

Isolated High-Low Gate Drive Interface Block Diagram

Typical TTL Interface Block Diagram

Applications


Ground loop

High speed line receiver

Microprocessor

system interface Pulse transformer

replacement

5 MBd Logic Gate Optocoupler


18/60

18


1 MBd Transistor Output Optocoupler

DescriptionThe circuit in the level shifting/TTL interfaceblock diagram shows how a 0 to 5 V logicsignal can be level shifted to a -15 to 0 Vsignal. This circuit can safely be used forlevel shifting up to 800 V. The circuit usesan open collector output logic gate, the74LS405, to drive the LED of the 6N135/6optocoupler. The 6N135/6 also has an open-collector output. The designer chooses RINto agree with the equation shown in the

schematic. This equation sets the value ofthe optocoupler LED forward current. Theoutput of the 6N135/6 requires a pull-upresistor, RL. The current-transfer ratio (CTR) ofthe optocoupler determines the maximumamount of current the optocoupler outputcan sink while maintaining the outputvoltage (between pins 5 and 6) of 0.5 V or less.

The benefit of the application is that itreduces the transient immunity problem andit is a convenient way of replacing the pulsetransformer for high-voltage level shifting.

Benefits

Allow level shiftingcapability

High current transfer ratio

Applications

Analog signalground isolation

High speed logicground isolation

Line receivers

Replace pulsetransformers

Replace slowphototransistorisolators

Typical Level Shifting/TTL Interface Block Diagram

IF

7

5

6

8

2

3

4

1INR

74LS05

INR = 5 - VF

HCPL-050L

+5 V

IF

LR

OLV

-15 V

IO (min) = IF CTR (min)

R L (min) = 15 VOL

IO(min) + I IL

IILIO

V IN

VOUT

1 MBd Transistor Output Optocoupler Product Selection

Device Part No. Package VDDV MaxVDDV

IF(on)mAMin.

CTR tPLHsMax.

tPHLsMax.


VIORMVpeak

%Min.

%Max.

IFmA

CMRV/s (Min.)

VCMV

Single Channel 6N135 300 mil DIP8 5 15 16 7 50 16 2.0 2.0 1000 10 3750/5000 # 630*6N136 300 mil DIP8 5 15 16 19 50 16 1.0 1.0 1000 10 3750/5000 # 630*HCNW135 400 mil DIP8 5 15 16 5 16 2.0 2.0 1000 10 5000 1414HCNW136 400 mil DIP8 5 15 16 19 50 16 1.0 1.0 1000 10 5000 1414HCPL-050L SO8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750 560*HCPL-0500 SO8 5 15 16 7 50 16 2.0 2.0 1000 10 3750 560*HCPL-0501 SO8 5 15 16 19 50 16 1.0 1.0 1000 10 3750 560*HCPL-250L 300 mil DIP8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750/5000 # 630*HCPL-2502 300 mil DIP8 5 15 16 15 22 16 0.8 0.8 3750/5000 # HCPL-2503 300 mil DIP8 5 15 8 15 8 2.5 1.5 3750/5000 #

ACPL-M50L-000E SO5 3.3/5 24 3 80 200 3 1.0 1.0 15000 1000 3750 560*

ACPL-W50L-000E^ Stretched SO6 3.3/5 24 3 53 200 3 1.0 1.0 15000 1000 5000 1140*

Dual Channel HCPL-053L SO8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750 560*HCPL-0530 SO8 5 15 16 7 50 16 2.0 2.0 1000 10 3750 HCPL-0531 SO8 5 15 16 19 50 16 1.0 1.0 1000 10 3750 HCPL-253L 300 mil DIP8 3.3/5 15 16 15 50 16 1.0 1.0 1000 10 3750/5000 # 630*HCPL-2530 300 mil DIP8 5 15 16 7 50 16 2.0 2.0 1000 10 3750/5000 # HCPL-2531 300 mil DIP8 5 15 16 19 50 16 1.0 1.0 1000 10 3750/5000 # HCPL-2533 300 mil DIP8 5 15 8 15 8 2.5 1.5 3750 ACPL-054L-000E SO8 3.3/5 24 3 53 200 3 1.0 1.0 15000 1000 3750 560*ACPL-K54L-000E^ Stretched SO8 3.3/5 24 3 53 200 3 1.0 1.0 15000 1000 5000 1140*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL 5000V RMS/1 minute Option 020, ^ - Advanced information, may subject to changes.

NCAnode

athode V

GND

8

7

6

5

2

3

4

C

C

1

no e 1

at o 1

at o

no e

2

8

7

6

5

1

2

3

4

6

5

4

1

3

6

5

4

1

2

3

NEW


19/60

19


m . . I L

1

1

4

1

1

.

IF

100 kBd Darlington Transistor Output Optocoupler Product Selection


IF(on)mAMin.

CTR tPLHsMax.

tPHLsMax.


VIORMVpeak%

Min.%Max.

IFmA

CMRV/s (Min.)

VCMV

Single Channel 4N45 300 mil DIP6 5 0.5 200 1000 10 500 50 3750 630

4N46 300 mil DIP6 5 0.5 200 1000 10 500 50 3750 630

6N138 300 mil DIP8 5 0.5 300 2600 1.6 50 15 1000 10 3750/5000 #

6N139 300 mil DIP8 5 0.5 400 5000 0.5 90 2 1000 10 3750/5000 # 630*

HCNW138 400 mil DIP8 5 0.5 300 1.6 70 11 1000 10 5000 1414

HCNW139 400 mil DIP8 5 0.5 400 0.5 11 11 1000 10 5000 1414

HCPL-070A SO8 5 0.04 800 25000 0.04 25 60 1000 10 3750 560*

HCPL-070L SO8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750 560*

HCPL-0700 SO8 5 0.5 300 2600 1.6 50 15 1000 10 3750 560*

HCPL-0701 SO8 5 0.5 400 5000 0.5 10 2 1000 10 3750 560*

HCPL-270L 300 mil DIP8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750/5000 # 630*

HCPL-4701 300 mil DIP8 5 0.04 800 25000 0.04 90 25 1000 10 3750/5000# 630*

HCPL-M700 SO5 5 0.5 300 2600 1.6 35 20 1000 10 3750 HCPL-M701 SO5 5 0.5 400 3500 0.5 10 2 1000 10 3750

Dual Channel HCPL-073A SO8 5 0.04 800 25000 0.04 130 25 1000 10 3750

HCPL-073L SO8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750 560*

HCPL-0730 SO8 5 0.5 400 5000 0.5 35 20 1000 10 3750

HCPL-0731 SO8 5 0.5 400 5000 0.5 35 20 1000 10 3750

HCPL-273L 300 mil DIP8 3.3/5 0.5 400 5000 0.5 90 30 1000 10 3750/5000 # 630*

HCPL-2730 300 mil DIP8 5 0.5 400 5000 0.5 35 20 1000 10 3750/5000#

HCPL-2731 300 mil DIP8 5 0.5 400 5000 0.5 60 20 1000 10 3750/5000#

HCPL-4731 300 mil DIP8 5 0.04 800 25000 0.04 90 25 1000 10 3750/5000#

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL 5000V RMS /1 minute Option 020

100 kBd Darlington Transistor Output Optocoupler

DescriptionThis differentially driven circuit can use upto eight 6N138 optocouplers at variousreceivers along the 90 m line. All stationsare isolated. The first station would drawapproximately 2.7 mA current, and the laststation 1.8 mA of LED drive current. Theoutput grounds of the optocoupler may beelectrically separate.

The benefit of the application is its simple,low-cost, multidrop circuit for low signal-ing rates.

Benefits

High CTR with low input current

Low power consumption

Typical Multidrop Line Receiver Block Diagram

GND

C

out

no e

a t o e

6

4

1

GND

VCC

V01

Anode 1

Cathode1

Cathode2

Anode2

V02

8

7

6

5

1

2

3

4

Applications

Digital logic groundisolation

FIA RS-232C line receiver

Low power systems andground isolation

Telephone ring detector

VO

VB

GND

1

2

3

6

5

4

ANODE

CATHODE

VCCNC

NC

ANODE

CATHODE

VE

VO

GND

8

7

6

5

1

2

3

4


20/60

20


R2Coupler (High Temperature, Automotive Grade)

DescriptionProven Quality and Reliability Track Record

Avago Technologies R2Coupler isolation prod-ucts are designed to meet the stringent re-quirements for the automotive market. Build-ing upon 35 years of optocoupler expertise,the automotive parts are manufactured in a TS16949 certified manufacturing facility and arePPAP supported. Robustness is demonstratedthrough qualification in accordance to AEC-Q100 Grade 1 guidelines. Avago optocouplershave been used extensively in long life andmission critical isolation applications such aslocomotive transportation, aerospace, militaryand industrial automation. Since the intro-duction of R2Coupler products in 2006, theseautomotive grade products have seen wideadoption by many automotive suppliers withmillions of units operating in the field.

Technology Leader

Avago Technologies is the first supplier to intro-duce 125C plastic optocouplers for automo-tive applications, with the largest portfolio ofoptocouplers ranging from IGBT gate drivers,isolation amplifier, high speed and low power

digital isolation and analog feedback isola-tion. Advanced LED technology enabled thebest-in-class performance over lifetime and athigh temperature. These optocouplers main-tain their very high voltage ratings with robustand reliable galvanic isolation technology withinternational component safety certifications(UL1577, IEC 60747-5-5, CSA Component Notice5). Optocouplers demonstrate superior EMIand common mode noise immunity.

Applications

Automotive IPM and gatedriver for inverters, DC-DCconverter and on-boardchargers

Automotive bus voltageand current/voltagesensing in inverters,converters and on-boardchargers

Automotive CANbus,UART, LIN and otherdigital communications

Isolated wake-up andstatus control andfeedback

Analog feedback in AC-DCand DC-DC converters

Low power digital

isolation in batterymanagement systems

Benefits Qualied to AEC-Q100 Grade 1 guidelines

TS 16949 manufacturing facility withPPAP support

Wide operating temperature (-40C to125C)

High CMR (30 kV/s at VCM=1kV)

Reinforced Reliability suitable forautomotive applications

Low input LED drive current

Worldwide Safety Approval (UL1577,IEC60747-5-5, CSA)


21/60

21


Automotive CANBus Block DiagramTypical Intelligent Power Module/Electric MotorInverter Block Diagram

CANTransceiver

BusInterface

OtherDevices

UARTNetwork

Controller

Tx Rx

ACPL-M61T/M71T/M72T

OtherDevices

Micro-Controller

Controlled Devices, e.g.Air-Compressor,

Lighting Control, BatteryManagement System,

etc.

at

o

e

cc

out

roun

no

e

at

o

e

Vcc

Vout

round

Anode

Automotive 10MBd Logic Gate Optocoupler

Device Part No. Package VISO(1min)VRMS

VIORMVpeak

OperatingTemperatureC

VCCV

ILEDmA

dV/dtmA

tPLHMax.ns

tPHLMax.ns

PWDMax.

tPSKMax.

CMRdV/dtkV/s

VCMV

Single Channel

Anode

Cathode

VDD

VO

GND

6

5

4

1

3

ACPL-M71T SO5 4000 560 -40 to 125 3.0 to 5.5 4 to 15 1.5 35 35 12 15 15 1000

ACPL-K71T^ SSO8 5000 1140 -40 to 125 3.0 to 5.5 4 to 15 1.5 35 35 12 15 15 1000

ACPL-M72T SO5 4000 560 -40 to 125 3.0 to 5.5 4 to 15 1.5 100 100 50 60 25 1000


Dual Channel LED Input

1

2

3

4

8

7

6

5

Anode1

Anode2

Cathode 1

Cathode 2

V 2DD

V 1D

VD2

GND



no e

atho e

C6

5

4

1

SHIELD

ACPL-M61T SO5 4000 560 -40 to 125 4.5 to 5.5 5 to 15 10 100 100 35 40 15 1000

Note: ^ - Advanced information, may subject to changes.


22/60

22


Automotive Analog Optocoupler

Device Part No. Package VISOVRMS

VIORMVpeak


VCCV

ILEDmA

CTRMin.%

(TA= 25 C) BWTyp.kHz

CMRdV/dtkV/s

CMRVCMVTyp.

%Min.%

6

5

4

1

3

ACPL-M43T SO5 4000 560 -40 to 125 20 5 to 15 20 45 32 1000 15 1500

ACPL-K43T^ SSO8 5000 1140 -40 to 125 20 5 to 15 24 65 32 1000 15 1500

ACPL-M49T SO5 4000 560 -40 to 125 20 4 to 10 20 45 32 15 1500

ACPL-K49T^ SSO8 5000 1140 -40 to 125 20 4 to 10 24 58 32 15 1500

Automotive Gate Drive Optocoupler

Device Features Part No. Package VISOVRMS

VIORMVpeak


VCCV

ILEDTyp.mA

lo_peakMax.A

ICCMax.mA

tPHLMax.ns

tPHLMax.ns

PWDMax.ns

tPSKMax.ns

CMRdV/dtkV/s

CMRVCMV

FAULTSHIELD

SHIELD

D

R

I

V

E

R

VCC1

GND1

RESET

VIN+VIN

2

3

4

5

1

13

10

14

9,12

16

15

DESAT

UVLO

LED1

LED2

11

FAULT6

7 8

VLED1+

VLED1 V

CC2VC

VOUT

VEE

VE

VLED2+

DESTAT

Desat,UVLO,FaultFeedback

ACPL-38JT SO16 5000 1230 -40 to 125 15 to30

Buered 2.5 1.5 500 500 300 350 15 1500

VCC

VO

N/C

Anode

Cathode

N/C

VO

VEE

8

7

6

5

1

2

3

4

UVLO ACPL-312T DIP8 3750 630 -40 to 125 15 to30 7 to 16 2.5 5 500 500 300 350 15 1500


Automotive 1MBd Transistor Output Optocoupler

Device Part No. Package VISOVRMS

VIORMV

peak

OperatingTemperature

C

VCCV

ILEDmA

CTRMin.

%

CTRTyp.

%

tPHLMax.

s

tPHLMax.

s

PWDMax.

s

tPSKMax.

s

CMRdV/dt

kV/s

CMRVCM

VSingle Channel

no e

atho e

C6

5

4

1

ACPL-M46T SO5 4000 560 -40 to 125 4.5 to 30 10 to 20 44 90 0.55 0.55 0.45 0.45 15 1500

6

5

4

1

3

ACPL-M43T SO5 4000 560 -40 to 125 20 5 to 15 20 45 1 1 0.45 0.5 15 1500

ACPL-K43T^ SSO8 5000 1 140 - 40 to 1 25 20 5 to 15 24 65 1 1 0.45 0.5 15 1500

ACPL-M49T SO6 4000 560 -40 to 125 20 4 to 10 20 58 100 100 0.45 0.5 15 1500

ACPL-K49T^ SSO8 5000 1 140 - 40 to 1 25 20 4 to 10 24 58 100 100 0.45 0.5 15 1500

ACPL-K23T^ SSO8 5000 1 140 - 40 to 1 25 20 0.8 to 10 19 130 20 20 15 1500

Dual Channel

1

2

3

4

8

7

6

5

Anode1

Anode2

Cathode1

Cathode2

VCC

VD1

VD2

GND

ACPL-K44T^ SSO8 5000 1 140 - 40 to 1 25 20 5 to 15 20 65 1 1 0.45 0.5 15 1500

ACPL-K24T^ SSO8 5000 1 140 - 40 to 1 25 20 0.8 to 10 19 130 20 20 15 1500


23/60

23


Extended Temperature R2Coupler

Device Part No. Pack-age


IOUTA(MAX)

IFmA

CTR tPLHs

Max.

tPHLs

Max.

PWD

ns

Max.

tPSKns

Max.


VIORMV

peak%Min.

%Max.

CMRV/s(Min.)

VCMV

ACPL-M43U-000E SO5 -40 to 125 NA 10 32 80 1.0 1.0 850 NA 15000 1500 3750 567

ACPL-M46U-000E SO5 -40 to 125 NA 10 44 90 0.4 0.6 450.0 NA 15000 1500 3750 567

ACPL-M61U-000E S05 -40 to 125 NA 5 NA NA 0.1 0.1 35 40 15000 1000 3750 567

ACPL-312U-000E DIP6 -40 to 125 2.5 7 N/A N/A 0.5 0.5 300 350(PDD)

25000 1500 3750 630NEW

NEW

NEW

NEW6

5

4

1

3

no e

a t o e

CC

GND

1

3 SHIELD

ATHODE

ANODE V C

GND

VO

6

5

4

VCC

VO

N/C

Anode

Cathode

N/C

VO

VEE

8

7

6

5

1

2

3

4

Automotive Miniature Analog Isolation Amplifier

Device Features Part No. Package VISOVRMS

VIORMV

peak

OperatingTemperature

C

VDDV

InputRange

Typ.V

GainTyp.

V/V

GainTol

Max.%

NonLMax.

%

Off-set

Max.mV

BWTyp.

kHz

CMRdV/dt

kV/s

CMRVCM

V

1

2

3

4

8

7

5

IDD1VDD1

IN+II

VINII

ND1

IDD2VDD2

V UT+

V UT

ND2

+

SHIELD

2% GainAccuracy

ACPL-782T DIP8 4000 891 -40 to 125 4.5 to5.5

0.2 8 2 0.35 4 100 10 1000

1

2

3

4

8

7

6

5

VDD1

VIN

SD

GND1

VDD2

VOP

VON

GND2SHIELD

DC VoltageSensing,Shut-downControl

ACPL-C87AT^ SSO8 5000 1140 -40 to 125 4.5 to5.5

0 to 2 1 1 0.3 100 10 1000

ACPL- C87BT^ SSO8 5000 1140 -40 to 125 4.5 to5.5

0 to 2 1 0.5 0.3 100 10 1000



24/60

24


ri ge + erial ata ut

-

HCPL-902J

-

Isolation

Barrier

erial Data In

Data Clock

Chip Select

r i g e

o

DescriptionThe ACML-74xx series of CMOS digital iso-

lators utilizes magnetic coupling throughthick insulation to provide high speed, high

insulation performance yet consuming lowpower at high data rates.

The HCPL-90xx/-09xx series CMOS digitalisolators integrated with giant magneto-resistive (GMR) technology enable high

speed performance and excellent transientimmunity specifications.

All devices operate at 3.3 V or 5 V supplyvoltages, boasting low power consumption.

They are able to withstand high common

mode voltages, 25kV/s at Vcm=1000V, and

meet UL 1577 and IEC 60950-1, IEC 61010-1

and IEC 60601-1 safety ratings.

Benefits

High insulation: UL1577 (5.6kVrms 1 minrating) and IEC 60950-1 and IEC 61010-1working voltage (up to 1132Vpeak)

High speed (100MBd), low PWD (3ns)and low Tp (18ns)

Wide temperature operation

(-40C to 105C)

Buer input and CMOS output(eliminate input/output resistors)

Multi-channel (1, 2 & 4-ch)

Low power consumption

Typical IsolatedA/D ConversionBlock Diagram

Digital Isolator

Digital Isolator ACML-74XX, HCPL-09XX AND HCPL-90XX Product Selection

Device Part No. Channel Package Max .Data Rate

MBd

Min.

tPLH& tPHL(VCC=5.0V)

ns

Max.

tPLH& tPHL(VCC=3.3V)

ns

Max.

PWDnsMax.

tPSKnsMax.


CMRV/s(Min.)

VCMV

HCPL-0900 Single SO8 100 15 18 3 6 15000 1000 2500

HCPL-9000 Single 300 mil DIP8 100 15 18 3 6 15000 1000 2500

HCPL-0930 Dual SO8 100 15 18 3 6 15000 1000 2500

HCPL-9030 Dual 300 mil DIP8 100 15 18 3 6 15000 1000 2500

HCPL-0931 Dual, Bi-Dir SO8 100 15 18 3 6 15000 1000 2500

HCPL-9031 Dual, Bi-Dir 300 mil DIP8 100 15 18 3 6 15000 1000 2500

ACML-7400 Quad SO16 Wide Body 100 32 36 2 5 25000 1000 5600

HCPL-090J Quad SO16 Narrow Body 100 15 18 3 6 15000 1000 2500HCPL-900J Quad SO16 Wide Body 100 15 18 3 6 15000 1000 2500

ACML-7420 Quad, 2/2, Bi-dir SO16 Wide Body 100 32 36 2 5 25000 1000 5600

HCPL-091J Quad, 2/2 Bi-dir SO16 Narrow Body 100 15 18 3 6 15000 1000 2500

HCPL-901J Quad, 2/2 Bi-dir SO16 Wide Body 100 15 18 3 6 15000 1000 2500

ACML-7410 Quad, 3/1, Bi-dir SO16 Wide Body 100 32 36 2 5 25000 1000 5600

HCPL-092J Quad, 3/1 Bi-dir SO16 Narrow Body 100 15 18 3 6 15000 1000 2500

HCPL-902J Quad, 3/1 Bi-dir SO16 Wide Body 100 15 18 3 6 15000 1000 2500

DD1

I

NC

2

U

VDD2

V E

8

63

4GalvanicIsolation

V

I

I

GND

U

V

U

alvanic

solation

4

12

13

4

16VDD1

3

4

1 GND

U 4

U

U 2

OUT

V

Ga

lvanicIsolation

3

4

6 11

14

V

IN

IN

U

U 4

2

I 4

I

U 2

U

V

alvanicIsolation

1

2

4

5

14

V

GND

I

I 2

IN

U 4

GND 2

IN

U 3

U

U

GND

V

GalvanicIsolation

I

U

GND

I 2

OUT7

54GalvanicIsolation

NEW

NEW

NEW

Applications

Digital eldbus isolation

Multiplexed datatransmission

Computer peripheralinterface

High speed digital systems

Isolated data interfaces

Logic level shifting


25/60

25


DSP

SOLAR PANEL

CHARGE CONTROLLER /

DC-DC CONVERTERINVERTER DC-AC

GATE

DRIVERS

CURRENT

SENSOR

ACPL-C79B/

C79A/C790

CURRENT

SENSOR

VOLTAGE

SENSOR

GATE DRIVER

ACPL-H342/K342

GATE DRIVERS

ACPL-H342/K342, 4X

VOLTAGE SENSOR

ACPL-C79B/C79A/C790

TO

POWER

GRID

PWM PWM

HV

HV+

ACPL-M61L,

2X

FIELD BUS COMMUNICATION

DescriptionThe ACPL-C79B/C79A/C790 isolation

amplifiers were designed for currentand voltage sensing in electronic power

converters in applications including motordrives and renewable energy systems.

Based on sigma-delta analog-to-digitalconverters, the new isolation amplifiers

feature high gain accuracy, low temperaturedrift of -50ppm/C, 3.3V/5V output supply

operation and a wide -40 to +105C

operating temperature range. Thesefeatures are delivered in a SSO-8 packagethat has a footprint 30% smaller than thestandard DIP-8 package. When mounted on

a PCB, it occupies a space that is a fractionof that for a traditional Hall Effect current

transducer.

The series is implemented with a fullydifferential circuit with gain accuracy of

0.5% (ACPL-C79B), 1% (ACPL-C79A), and3% (ACPL-C790). With a 200kHz bandwidth

and 1.6s response time, the ACPL-C79xcaptures transients during short circuitand overload conditions. Operating from

a single 5V supply, the isolation amplifierseries features an excellent nonlinearity of

0.05% and a SNR of 60dB.

Miniature Analog Isolation Amplifier

Example Application: Block diagram of a micro-inverterwith simplified DC-DC-AC topology.

Benefits

Compact packagesuitable for high volumeproduction process

Cost-eective solution

Reinforced insulation

Applications

Motor phase and railcurrent sensing

Data acquisition systems

Inverter current sensing

General purpose currentsensing and monitoring


26/60

26


Isolated Sigma-Delta Modulator

Device Part No. Package OperatingTemperatureC

Gain Errorat 25C% Max.

INLLSBTyp.

ENOBBitsTyp.

VDD2V

CMR - V/s@VCM ClockMHzTyp.

VISOVRMSMin.

VIORMVpeakCMR

V/s(Typ.)

VCMV

VDD2

GND2

NC

MCLKIN

GND2

NC

MDAT

VIN

VDD1

VIN+

MOD.

DATA

OUT

CLK

DET.

CLK

IN

GND1

NC

GND1

VDD1

NC

NC

1

2

3

4

5

6

7

8

16

15

14

13

12

11

10

9

L

ACPL-796J-000E SO16 -40 to +105 1 3 12 3 - 5.5 25000 1000 5 - 20,External

5000 1230*

211

NCNC

NCDAT

0NC C

9GND1 ND2

6

15

DD1

VIN+

GND2

C

14VIN VDD2

4 3NC CLKSIGMA-DELTAMOD./

HCPL-786J SO16 -40 to +85 2 3 11 4.5 - 5.5 20000 1000 10, Internal 5000 1230

1

2

4

8

7

6

VDD1

IN+

V N

DD2

MCLK

MDAT

GND2SHIELD

ISOLATION

DECODE

-T

.

ACPL-C797-000E Stretched SO8 -40 to +105 1 3 12 3 - 5.5 25000 1000 10, Internal 5000 1230

ACPL-7970 DIP8 -40 to +105 1 3 12 3 - 5.5 25000 1000 10, Internal 5000 891

HCPL-7860 DIP8 -40 to +85 1 (Matching) 3 11 4.5 - 5.5 20000 1000 10, Internal 3750 891

HCPL-7560 DIP8 -40 to +85 5 64 8 4.5 - 5.5 20000 1000 10, Internal 3750 891*

1

11

A 1

MCLK2 THR1

CO -

VERSION

INTER-

FACE

C O G .

INTER-

FACE

0MDAT2 1

9GND RESET

1 1

1A A

4CDAT SCLK

41 A

C 1

C

-

HOLD

C

&

HCPL-0872 SO16 -40 to +85 Dual, Programmable Digital Filterwith SPI Interface

4.5 - 5.5 NA NA ModulatorClock

NA NA

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes, - VDD

NEW

NEW

Miniature Isolation Amplifier

Device Part No. Package OperatingTemperature

C

Gain Errorat 25C

% Max.

Non-linearity

% Typ.

Band-width

kHz Typ.

VDD2V

CMR - V/s@VCM OutputConfigura-

tion

VISOVRMS

Min.

VIORMV

peakCMRV/s(Typ.)

VCMV

1

2 7

DD1V D1

VN+

IN

GND1

IDD2VDD2

VOUT+

VOUT

ND2SHIELD

ACPL-C78A-000E Stretched SO8 -40 to +85 1 0.0037 100 4.5 - 5.5 15000 1000 Differential 5000 1230*

ACPL-C780-000E Stretched SO8 -40 to +85 3 0.0037 100 4.5 - 5.5 15000 1000 Differential 5000 1230*

ACPL-C784-000E Stretched SO8 -40 to +85 5 0.0037 100 4.5 - 5.5 15000 1000 Differential 5000 1230*

ACPL-782T-000E R2Coupler DIP8 -40 to +125 2 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891

ACPL-C79B-000E Stretched SO8 -40 to +105 0.5 0.05 200 3 - 5.5 15000 1000 Differential 5000 1230

ACPL-C79A-000E Stretched SO8 -40 to +105 1 0.05 200 3 - 5.5 15000 1000 Differential 5000 1230

ACPL-C790-000E Stretched SO8 -40 to +105 3 0.05 200 3 - 5.5 15000 1000 Differential 5000 1230

ACPL-790B DIP8 -40 to +105 0.5 0.05 200 3 - 5.5 15000 1000 Differential 5000 891

ACPL-790A DIP8 -40 to +105 1 0.05 200 3 - 5.5 15000 1000 Differential 5000 891

ACPL-7900 DIP8 -40 to +105 3 0.05 200 3 - 5.5 15000 1000 Differential 5000 891

HCPL-7800A DIP8 -40 to +85 1 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891

HCPL-7800 DIP8 -40 to +85 3 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891

HCPL-7840 DIP8 -40 to +85 5 0.0037 100 4.5 - 5.5 15000 1000 Differential 3750 891*

VIN+

V - 23

5

7

8

15

14

12

10

9

CHCL

VDD1

VDD1 DD2

DD2

REF

VOUT

BSVAL

AULT

ND ND

ND

VLED+

HCPL-788J SO16 -40 to +85 3 0.06 30 4.5 - 5.5 25000 1000 Single-ended 5000 1230

ACPL-785J-000E SO16 -40 to +85 5 0.06 30 4.5 - 5.5 25000 1000 Single-ended 5000 1230*

1

2

3

4

8

7

6

I D1D1

VN+

IN

I D2VDD2

VOUT

VREF

+

SHIELD

HCPL-7510 DIP8 -40 to +85 3 0.06 100 4.5 - 5.5 15000 1000 Single-ended 3750 891*

HCPL-7520 DIP8 -40 to +85 5 0.06 100 4.5 - 5.5 15000 1000 Single-ended 3750 891*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information.

NEW

NEW

NEW

NEW

NEW

NEW


27/60

27


Integrated Gate Drive Optocoupler

DescriptionIn typical motor drive and renewable

energy power conversion systems, there areseveral signals between the power devices

and the micro-controller that need isolationand additional customized functionssuch as gate drive and current/voltage

sensing. Avago Technologiesgate drive andisolation amplifier products provide low

cost, high performance solutions for suchapplications.

High performance motor drives require

precision timing for turning on and offthe power devices on the inverter whilerenewable energy inverter needs to bereliable and e cient when converting DC-

link voltage to usable AC power output. Themicrocontroller that controls these functions

needs to be isolated from the high voltageinverter side. Avago Technologies offers

a variety of optocouplers that have built-in gate drive capability. These gate driveoptocouplers come in wide range of output

current from 0.4A to 5A, and selected parts

with integrated protection features such asActive Miller Clamp, under voltage lockout,

fault Status feedback and desaturationdetection. For solutions that require lower

output power capability, IPM interfaceoptocouplers will meet the need.

Benefits

Rail-to-rail output voltage for reliableIGBTs drive

Integrated fault protection and feedbackto reduce component count and solutioncost

Short propagation delay for fasterswitching

Fast IGBT switching for improvede ciency

Low power consumption for bootstrapoperation

High common mode transient rejectionensures reliable operation under noisyenvironment

Direct drive of high power IGBTs


Typical Motor Drive Block Diagram

Applications

Isolated IGBT/MOSFETgate drive

AC and brushless DCmotor drives

Renewable energy

inverters Industrial inverters

Switching power supplies

Uninterruptible powersupplies (UPS)

MICRO CONTROLLER

RECTIFIER

AC-DC

CHARGE CONTROLLER /

DC-DC CONVERTERINVERTER DC-AC

M

R

S

T

CURRENT SENSOR

ACPL-C79B/C79A/C790

CURRENT

SENSOR, 3X

VOLTAGE

SENSOR

GATE DRIVE

ACPL-332J

GATE DRIVE

ACPL-332J

VOLTAGE SENSOR

ACPL-C79B/C79A/C790


28/60

28


Integrated Gate Drive Optocoupler Product Selection

Device Part No. Package IF(on)mA

Min.

lOUTA

Min.

lOUTA

Max.

tPLHs

Max.

tPHLs

Max.

PDDs

Max.

VCCV

Max.


Min.

VIORMV

peak

CMR

V/s (Min.)

VCM

V

Single Channel

VCC

VOUT

N/C

VEE

1

2

3

4

8

7

6

5

CATHODE

ANODE

N/C

N/C

ACNW3430-000E^ 400 mil DIP 7 3.0 4.0 0.35 0.35 0.2 30 40000 1500 5000 1414

VCC6

VOUT5

VEE4

2N/C

1ANODE

4CATHODE

ACPL-P343-000E Stretched SO6 7 3.0 4.0 0.20 0.20 0.1 30 35000 1500 3750 891*

ACPL-W343-000E Stretched SO6 7 3.0 4.0 0.20 0.20 0.1 30 35000 1500 5000 1140*





VCC

VOUT

VCLAMP

VEE

1

2

3

4

8

7

6

5

CATHODE

NC

ANODE

NC

VCLAMP

ACPL-H342-000E Stretched SO8 7 2.0 2.5 0.35 0.25 -0.2 30 40000 1500 3750 891*

ACPL-K342-000E Stretched SO8 7 2.0 2.5 0.35 0.25 -0.2 30 40000 1500 5000 1140*

VCC

VO

N/C

Anode

Cathode

N/C

VO

VEE

8

7

6

5

1

2

3

4

ACPL-312U-000E 300 mil DIP 7 2.0 2.5 0.5 0.5 0.35 30 25000 1500 3750 630

SHIELD

SHIELD

D

R

I

V

E

R

VE

DESAT

VCC2

VOUT

VCLAMP

VEE

VCC1

VS

FAULT

ANODE

CATHODE

VCLAMP

VLED

6,7

5,8

2

3

1,4

13

11

14

9,12

10

16

15

DESAT

UVLO

LED1

LED2

ACPL-330J-000EACPL-331J-000E

SO16 8 1.0 1.5 0.25 0.25 0.35 30 15000 1500 5000 1230

1.5A Highly Integrated Gate Drive Optocoupler with Active Miller Clamp, Over-Current Protection and Fault Feedback Under Voltage Lock-Out Protection (UVLO) with Hysteresis

Automatic Fault Reset after xed delay time (for ACPL-330J-000E only)

ACPL-332J-000EACPL-333J-000E

SO16 8 2.0 2.5 0.25 0.25 0.35 30 15000 1500 5000 1230

2.5A Highly Integrated Gate Drive Optocoupler with Active Miller Clamp, Over-Current Protection and Fault Feedback Under Voltage Lock-Out Protection (UVLO) with Hysteresis Automatic Fault Reset after xed delay time (for ACPL-333J-000E only).

1

3

2

4

8

6

7

5

ACPL-H312-000E Stretched SO8 7 2.0 2.5 0.5 0.5 0.35 30 15000 1500 3750 891*

ACPL-K312-000E Stretched SO8 7 2.0 2.5 0.5 0.5 0.35 30 15000 1500 5000 1140*

61

52

43

ANODE

N.C.

CATHODE

VCC

VO

VEESHIELD





VO

VEE

1

3

2

4

8

6

7

5SHIELD

CATHODE

ANODE

N/C

N/C VCC

VEE

ACNW3190-000E 400 mil DIP8 10 4.0 5.0 0.5 0.5 0.3 30 15000 1500 5000 1414

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW

NEW


29/60

29


Integrated Gate Drive Optocoupler Product Selection


Min.

lOUTA

Min.

lOUTA

Max.

tPLHs

Max.

tPHLs

Max.

PDDs

Max.

VCCV

Max.


Min.

VIORMV

peak

CMR

V/s (Min.)

VCMV

1

3

SHIELD

2

4

8

6

7

5

/C

CATHODE

ANODE

/C

V C

V

N/C

V E

ACNW3130-000E 400 mil DIP8 10 2.0 2.5 0.5 0.5 0.35 30 40000 1500 5000 1414

ACPL-3130-000E 300 mil DIP8 7 2.02.5

0.5 0.5 0.35 30 40000 1500 3750 630*

ACPL-J313-000E 300 mil DIP8 7 2.02.5

0.5 0.5 0.35 30 40000 1500 3750 1230^

ACPL-T350-000E 300 mil DIP8 7 2.02.5

0.5 0.5 0.35 30 15000 1500 3750 630*

HCNW3120 400 mil DIP8 10 2.02.5

0.5 0.5 0.3 30 25000 1500 5000 1414

HCPL-J312 300 mil DIP8 7 2.02.5

0.5 0.5 0.35 30 25000 1500 3750 1230^

HCPL-J314 300 mil DIP8 8 0.40.6

0.7 0.7 0.5 30 25000 1500 3750 891

HCPL-T250 300 mil DIP8 7 0.5 1.5 0.5 0.5 30 5000 600 3750 630*

HCPL-T251 300 mil DIP8 8 0.1 0.4 1.0 1.0 30 10000 600 3750

HCPL-0302 SO8 7 0.2 0.4 0.7 0.7 0.5 30 10000 1000 3750 566*

HCPL-0314 SO8 8 0.4 0.6 0.7 0.7 0.5 30 25000 1000 3750 566*

HCPL-3020 300 mil DIP8 7 0.2 0.4 0.7 0.7 0.5 30 10000 1000 3750 630*

HCPL-3120 300 mil DIP8 7 2.0 2.5 0.5 0.5 0.35 30 25000 1500 3750 630*

HCPL-3140 300 mil DIP8 8 0.4 0.6 0.7 0.7 0.5 30 25000 1000 3750 630*

HCPL-3150 300 mil DIP8 7 0.5 0.6 0.5 0.5 0.35 30 15000 1500 3750 630*

HCPL-3180 300 mil DIP8 10 2.0 2.5 0.2 0.2 0.09 20 10000 1500 3750 630*

6

5

4

13

2

1

0

12

3

4

6

7

8

VEVLED2+

ESAT

VCC2

VC

VOUT

VEE

VEE

VN+VIN-

VCC1

GND1

RESET

FAULT

VLED1+

VLED1-

HCPL-316J SO16 2.0 2.5 0.5 0.5 0.3 30 15000 1500 5000 1230 2.0 A Highly Integrated Gate Drive Optocoupler with over-current Protection and Fault Feedback CMOS compatible Under Voltage Lock-Out Protection (UVLO) with Hysteresis

Dual Channel1

3SHIELD

2

8

6

4

9

/C

ATHODE

ANODE

/C

VCC

VEE

VO

VEE

7

6

0

1

ATHODE

ANODE

VO

VCC

SHIELD

HCPL-314J SO16 8 0.4 0.6 0.7 0.7 0.5 30 25000 1500 5000 1230

HCPL-315J SO16 7 0.5 0.6 0.5 0.5 0.35 30 15000 1500 5000 1230

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, ^ - Advanced Information, may subject to changes.


30/60

30


Intelligent Power Module (IPM) Based Inverter Block Diagram

DescriptionThe ACNV/HCNW/HCPL-45xx and ACPL-

48xx series optocouplers are designedfor Intelligent Power Module (IPM)

drive applications such as inverters andmotor control systems. These high speedoptocouplers have high CMR performance

that helps to reject common mode noise in

such high voltage systems. The output of

HCNW/HCPL-45xx devices is conventionalopen-collector; the output of ACPL-48xx

devices came with totem pole output stage

eliminates the necessity of using the pull-upresistor and allows direct drive to the IPM.ACNV45xx devices allow very high workingvoltage for use in Renewable Energy Supply

system.

In addition to Intelligent Power Moduledrive, the ACNV/HCNW/HCPL-45xx and

ACPL-48xx series optocouplers can be usedin general purpose isolation applications

like high speed logic ground isolation,isolated line receivers, and microprocessorsystem interfaces.

Benefits

Short propagation delay for fasterswitching

Fast IGBT switching for improved

e ciency High Common Mode Transient Rejection

ensures reliable operation under noisyenvironment

Wide operating temperature range


Intelligent Power Module Interface Optocoupler

Applications

Intelligent power module

Inverter/Motor control

Power switch design

General purpose digitalisolation

Typical Level Shifting/TTL Interface Block Diagram

SHIELD

20K

ACNV4506 +15V

NOTE: FOR BEST CMR PERFORMANCE, CONNECT PIN 6 TO PIN 7

1

2

3

5

10

9

8

6

4 7

+5V

74LS05

RIN

RINIF

VIN

IF

VOUTVOL

ILIO

5 - VF=

IO (min)= IF CTR (min)

VOL= 15 RL {IO(min) + IIL}

=15-RL {IF CTR (min) + IIL}

CURRENT SENSE

M

MCUANDPWMGENERATOR

VCC

VCC

IN_UH

GND

IPM HV

U

V

W

U V W

HV+

IN_UL

ACPL-M484/P484/W484, OR

ACPL-M483/P483/W483

FOR PHASES U, V AND W

COMMON 15V TO 20V

POWER SUPPLY

HVICGATEDRIVE

+

HVICGATEDRIVE

HVICGATEDRIVE


31/60

31



Min.

CTR tPLHs

Max.

tPHLs

Max.

PDD

s

Max.


VIORMV

peak%Min. %Max. IF

mA CMRV/s (Min.) VCM

V

Single Channel ACPL-M483-000E^ SO5 4 0.10 0.10 0.10 20000 1000 3750 567*

ACPL-P483-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 3750 891*

ACPL-W483-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 5000 1140*

ACPL-M484-000E^ SO5 4 0.10 0.10 0.10 20000 1000 3750 567*

ACPL-P484-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 3750 891*

ACPL-W484-000E^ Stretched SO6 4 0.10 0.10 0.10 20000 1000 5000 1140*

ACNV4506-000E 500 mil DIP10 10 44 10 0.55 0.40 0.50 30000 1500 7500 2262*

7

1

2

3

4 5

6

8NC

Anode

Cathode

DNGCN

NC

SHIELD

V

V

CC

O

ACPL-4800-000E 300 mil DIP8 6 0.35 0.35 0.25 30000 1000 3750 630*

6

5

4

1

3

ACPL-M43U-000E SO5 10 32 80 10 1 1 0.9 15000 1000 3750 567*

Ano e

a t o e

CC

O

6

4

1

H L

ACPL-M46U-000E SO5 10 44 90 10 0.4 0.55 0.45 15000 1000 3750 567*

ACPL-P456-000E Stretched SO6 10 44 >90 10 0.55 0.45 0.45 15000 1500 3750 891*

ACPL-W456-000E Stretched SO6 10 44 >90 10 0.55 0.45 0.45 15000 1500 5000 1140*

ACPL-P480-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 3750 891*

ACPL-W480-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 5000 1140

ACPL-P481-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 3750 891*

ACPL-W481-000E Stretched SO6 6 0.35 0.35 0.25 20000 1000 5000 1140*

V

NC

NC

NC

Anode

Cathode

SHIELD

V

ND

8

7

54

C

ACPL-K453-000E Stretched SO8 16 19 50 16 1.00 1.00 1.00 15000 1500 5000 1140*

V

NC

Anode

Cathode

V

ND

5

4

2

3

O

HIELD

ACPL-P454-000E Stretched SO6 12 26 65 12 1.14 1.00 1.30 15000 1500 3750 891*

ACPL-W454-000E Stretched SO6 12 26 65 12 1.14 1.00 1.30 15000 1500 5000 1140*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000VRMS/1 minute Option 020,^ - Advanced information, may subject to changes.

NEW

NEW

NEW

NEW

NEW

NEW

NEW

Intelligent Power Module Interface Optocoupler Product Selection


32/60

32



Min.

CTR tPLHs

Max.

tPHLs

Max.

PDD

s

Max.


VIORMV

peak%Min. %Max. IF

mA CMRV/s (Min.) VCM

V

V

NCnode

athode V

GND

1

4

O

HCNW4502 400 mil DIP8 16 19 50 16 1.0 1.0 1000 10 5000 1414

HCNW4503 400 mil DIP8 16 19 50 16 1.0 1.0 15000 1500 5000 1414

HCNW4504 400 mil DIP8 12 25 65 12 1.4 1.0 1.3 15000 1500 5000 1414

HCPL-0452 SO8 16 19 50 16 1.0 1.0 1000 10 3750 560*

HCPL-0453 SO8 16 19 50 16 1.0 1.0 1.0 15000 1500 3750 560*

HCPL-0454 SO8 12 26 65 12 1.4 1.0 15000 1500 3750 560*

HCPL-4502 300 mil DIP8 16 19 50 16 1.0 1.0 1000 10 3750/5000 # 630*

HCPL-4503 300 mil DIP8 16 19 50 16 1.0 1.0 1.0 15000 1500 3750/5000 # 630*

HCPL-4504 300 mil DIP8 12 26 65 12 1.4 1.0 1.3 15000 1500 3750/5000 # 630*

HCPL-J454 300 mil DIP8 12 21 65 12 0.7 0.5 1.3 15000 1500 3750 891

V C

V

NC

NC

Cathode

Anode

V

GND

8

72

3

SHI L

k W

HCNW4506 400 mil DIP8 10 44 >90 10 0.55 0.40 15000 1500 5000 1414

HCPL-0466 SO8 10 44 >90 10 0.55 0.48 0.45 15000 1500 3750 560*

HCPL-4506 300 mi l DIP8 10 44 >90 10 0.55 0.40 0.45 15000 1500 3750/5000 # 630*

HCPL-J456 300 mi l DIP8 10 44 >90 10 0.55 0.40 0.45 15000 1500 3750 891

VAnode

Cathode

V

GND4

O

SHIELD

HCPL-M452 SO5 16 20 50 16 1.0 1.0 1000 10 3750 567*

HCPL-M453 SO5 16 20 50 16 1.0 1.0 1.0 15000 1500 3750 567*

HCPL-M454 SO5 12 26 65 12 1.4 1.0 1.3 15000 1500 3750 560*

Anode

athode

VCC

VO

GND

5

4

1

SHI L

HCPL-M456 SO5 10 44 >90 10 0.55 0.40 0.45 15000 1500 3750 560*

Dual Channel

V

V01

node1

Cathode

Cathode 2

node

V

ND

2

3

HCPL-0534 SO8 16 19 50 16 1.0 1.0 15000 1500 3750 560*

HCPL-4534 300 mil DIP8 16 19 50 16 1.0 1.0 15000 1500 3750/5000 # 630*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, # - with UL 5000VRMS/1 minute Option 020,^ - Advanced information, may subject to changes.

Intelligent Power Module Interface Optocoupler Product Selection


33/60

33


DescriptionThe HCPL-2602/12 have input current

regulators and integrated high gain photodetectors. The input regulator serves as a

line terminator for line receiver applications.The higher LED threshold voltage providesimproved immunity to differential noise and

the rejection internally shielded detector

provides better common-mode rejection

with no sacrifice in speed.

The diagram below illustrates an unbalanced

line receiver using the integrated voltage-

clamp input optocoupler, HCPL-2602.TTL data is converted to a differentialsignal viathe differential line driver, andtransmitted over twisted-pair wire. The

Schottky diode helps to improve the turn-on and turn-off delays.

Benefits Line termination included no extra

circuitry required

Isolated Line Receiver

Typical Block Diagram

8

7

6

5

.01.0F

390

15 pF

R

1

2

3

4HCPL-2602/12

HABT-5400

1

2

4

3

BELDEN 8777

l

VCC

GND

5

6

7

16

+5V

8

1/2 9614

VO

+5V

VN

Line Receiver Product Selection

Device Part No. Package Output Collector OutputmA Max.

tPLHsMax.

tPHLsMax.

CMR - V/s@VCM VISOVRMSMin.CMR

V/s (Min.)VCMV

HCPL-2602 300 mil DIP8 50 100 100 1000 50 3750

HCPL-2612 300 mil DIP8 50 100 100 3500 300 3750

40 ns max propagation delay skew (part to part)Line termination circuitry included

1

2

3

4

8

7

6

5

IN

IN+

GND

V

VCC

O

VE

NC

CATHODESHIELD

Applications

Isolated line receiver


Microprocessor systeminterface

Digital isolation for A/D,D/A conversion

Current sensing

Instrument Input/Outputisolation

Ground loop elimination

Pulse transformerreplacement

Power transistor isolationin motor drives


34/60

34


20 mA Current Loop Transmitter/Receiver Product Selection

Device Part No. Package Data Rate

kBd @ (meters)

tPLHsMax.

tPHLsMax.

CMR - V/s@VCM VISOVRMSMin.CMR

V/s (Min.)VCMV

Transmitter HCPL-4100 300 mil DIP8 20 (400) 1.6 1.0 1000 50 3750

CMOS compatible data input for HCPL-4100

Receiver HCPL-4200 300 mil DIP8 20 (1400) 1.6 1.0 1000 50 3750

CMOS compatible data input for HCPL-4200

VNC

NC

C

C

C

+

-

V

ND

8

7

6

5

1

2

3

4

VCC

VO

I+

I-

VE

GND

8

7

6

5

1

DescriptionData transmission between electronic

equipment which are physically separatedby a distance of more than a few feet

can be achieved by using the HCPL-4100 (transmitter) and the HCPL-4200(receiver) optocouplers. These devices

include specialized circuits for 20 mAdigital current loop applications, and are

designed to easily interface TTL and CMOSlogic systems to current loop systems.

20 mA current loop systems conventionally

signal a logic high state by transmitting20 mA of loop current, and signal a logic low

state by allowing no more than few milli-amperes of loop current. Optical coupling

loops break ground loops and provide

very high immunity to common mode

interference. These devices are simple to use

in a data transmission system for industrialapplications and maintainintegrity.

Benefits

Direct control of the 20 mA current loop

High noise immunity

Isolated 20 mA Current Loop Transmitter/Receiver


Applications

Isolated 20 mA currentloop transmitter in:

Industrial controlequipment

Computer peripherals

Data communicationsequipment

GND

SHIELD

V

IE

VO

IO

7

5

62

VI

1I +

I -

I

8 V

ICC

HCPL-4100 Transmitter

IO

I

VO

IO

I

+

SHIELD 4

3

CC

GND

ICC

VI

5

I


35/60

35


DescriptionIn the implementation of an interface from

an electrically noisy environment into logicsystems, it is often desirable to establish

some current or voltage switching pointor input switching threshold the HCPL-

3700 optocoupler provides such a solution.

This device combines an AC or DC voltageand/or current detection function with

high sensing input buffer ICs which permitcontrol of threshold levels over a wide range

like sensing industrial control systems, and

ring detection in telephone system micro-processor interfacing.

The HCPL-0370/3700/3760 threshold-sens-ing optocoupler can be used for sensing the

AC/DC power on/off condition. At the

Isolated Voltage/Current Detector


Isolated Voltage/Current Detector

Device Part No. Package Input Threshold Current HysteresismAtyp

tPLHsMax.

tPHLsMax.


VIORMVPEAK

mA CMRV/s (Min.)

VCMVMin. Max.

ACPL-K370-000E Stretched SO8 1.96 3.11 1.2 40 15 600 140 3750/5000# 1140*

ACPL-K376-000E Stretched SO8 0.87 1.56 0.6 40 15 600 140 3750/5000# 1140*

HCPL-0370 SO8 1.96 3.11 1.2 40 15 600 140 3750 567*

HCPL-3700 300 mil DIP8 1.96 3.11 1.2 40 15 600 140 3750 630*

HCPL-3760 300 mil DIP8 0.87 1.56 0.6 40 15 600 140 3750 630*

Notes: * - with IEC/EN/DIN EN 60747-5-2/5 Option 060, #- with UL 5000VRMS/1 minute Option 020, ^- Advanced information, may subject to changes.

A

+

-

A

Applications

Limit switch sensing

AC/DC voltage andcurrent detector

Relay contact monitor

Relay coil voltage monitor

User congurablevoltage/current limitdetection

Microprocessorinterfacing

L

R /2

K

AC INPUT CONFIGURATION

L

AC

+

-

AC

V

GND

DC UP TO

1140 V

I

GND

DC+

INPUT

I

DC INPUT

I

8

DC+

DC- V

I I I

I

optocoupler input, only a pair of seriesresistors RX/2 are required to limit the

current. The AC signal can be filteredwith a capacitor at either the input or the

output of the optocoupler. The value of RXdetermines the threshold sensing voltage.

HCPL-0370/3700/3760s low threshold

current reduces power dissipation and itsbuilt-in diode bridge and hysteresis circuit

reduces the number of external compo-nents used.

Benefits Low threshold current reduces power

dissipation

Hysterisis circuit reduces externalcomponents and PCB size


36/60


37/60

37


DescriptionThe HCPL-4562 and HCNW 4562 are

recommended for very high bandwidth(up to 15 MHz) AC analog designs such as

coupling audio or video signals.

This circuit, with the HCPL-4562 wideband

analog/video optocoupler, is optimized forvideo signal coupling. The peaked responseof the detector circuit helps extend the

frequency range over which the gain isrelatively constant. The number of gain

stages, the overall circuit topology, and the

DC bias point are all chosen to maximizethe bandwidth.

HCPL-4562 provides simple and cost effec-tive solutions for coupling audio and video

signals.

Benefits

Optimized for video signal coupling

Simple design for audio and videocoupling

Cost eective


Wideband Analog/Video Optocoupler


8

7

6

5

2CC1

2

3

4

V

OUT

HIGHIMPEDANCELOAD

Q Q = 2N39041 4

Q4

Q3

R9

750R6

9.1 K

R11

470

2

R8

1.0 K

R10

100

22

R7

15 K

Q2

R2

1.0 K

R1

6.8 K

1N4150

D1

500

51

R3

100

C1

47 F

Q1

VE

R4

= POTENTIOMETER+51RESISTOR

1CCV

IN

GV= VOUT/VIN

Wideband Analog/Video Optocoupler Product Selection

Device Part No. Package BandwidthMHztyp

DC Non-Linearity%Max.

CTR%typ

IMRRdBtyp

VISOVRMSMin.

VIORMVpeak

HCNW4562 400 mil DIP8 9 0.15 52 119 5000 1414

HCPL-4562 300 mil DIP8 17 0.25 45 122 3750/5000# 630*

0.3% / C gain temperature coecient

Notes:

* - with IEC/EN/DIN EN 60747-5-2/5 Option 060

# - with UL 5000V RMS /1 minute Option 020

7

1

2

3

4 5

6

8NC

ANODE

CATHODE

NC

VCC

VB

VO

GND

Applications

Video isolation for thefollowing standards/formats:

NTSC, PAL, SECAM, S-VHS,ANALOG RGB

Low drive currentfeedback

Element in switchingpower supplies:ISDN networks

A/D converter signalisolation

Analog signal groundisolation

High voltage insulation


38/60


39/60

39


General Purpose Phototransistor Optocoupler DC Input Product Selection

Device Part No. Package Absolute

Max. IFmA

CTR VCE(sat) tr/tfstyp

BVCEOVMin.

VF VISOVRMSMin.

Note

%Min.

%Max.

IFmA

VCEV

VMax.

IFmA

ICmA

VMax.

IFmA

Single Channel-4 pin ACPL-217-500E

(Half pitch)

SO4 50 50 600 5 5 0.4 8 2.4 2/3 80 1.4 20 3000 1

HCPL-181-000E# SO4 50 50 600 5 5 0.2 20 1 4/3 80 1.4 20 3750 1

HCPL-817-000E* 300 mil DIP4 50 50 600 5 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3

Single Channel-6 pin 4N25-000E 300 mil DIP6 80 20 10 10 0.5 50 2 3/3 30 1.5 10 2500 1/2/3

4N35-000E 300 mil DIP6 60 100 10 10 0.3 50 2 3/3 30 1.5 10 3550 1/2/3

CNY17-1-000E 300 mil DIP6 60 40 80 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3

CNY17-2-000E 300 mil DIP6 60 63 125 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3

CNY17-3-000E 300 mil DIP6 60 100 200 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3

CNY17-4-000E 300 mil DIP6 60 160 320 10 5 0.3 10 2.5 5/5 70 1.7 60 5000 1/2/3

Dual Channel-8 pin ACPL-227-500E(Half pitch)

SO8 50 50 600 5 5 0.4 8 2.4 2/3 80 1.3 20 3000 1

ACPL-827-000E @ 300 mil DIP8 50 50 600 5 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3

Quad Channel-16 pin ACPL-247-000E(Half pitch)

SO16 50 50 600 5 5 0.4 8 2.4 2/3 80 1.3 20 3000 1

ACPL-847-000E 300 milDIP16

50 50 600 5 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3

Anode

Cathode

4

3

1

2

Collector

Emitter

Base

Collector

Emitter

Anode

Cathode

6

5

4

1

2

3

1 2 3 4

8 7 6 5

1 2 3 4

8 7 6 5

ll

1 2 3 4

16 15 14 13

5 6 7 8

12 11 10 9

1 2 3 4

16 15 14 13

5 6 7 8

12 11 10 9

ll

NEW

NEW

NEW

NEW

NEW

General Purpose Phototransistor Optocoupler AC Input

Device Part No. Package Absolute

Max. IFmA

CTR VCE(sat) tr/tfs

typ

BVCEOV

Min.

VF VISOVRMSMin.

Note

%Min. %Max. IF

mA VCE

V VMax. IF

mA IC

mA VMax. IF

mA

Single Channel-4 pin ACPL-214-500E

(Half pitch)SO4

+/-5020 400 5 5 0.4 8 2.4 2/3 80 1.4 20 3000 1

HCPL-354-000E SO4 +/-50 20 400 1 5 0.2 20 1 4/3 35 1.4 20 3750 1

HCPL-354-00AE SO4 +/-50 50 150 1 5 0.2 20 1 4/3 35 1.4 20 3750 1

HCPL-814-000E 300 mil DIP4 +/-50 20 300 1 5 0.2 20 1 4/3 35 1.4 20 5000 1/2/3

HCPL-814-00AE 300 mil DIP4 +/-50 50 150 1 5 0.2 20 1 4/3 35 1.4 20 5000 1/2/3

Dual Channel-8 pin ACPL-224-500E(Half pitch)

SO8 +/-50 20 400 1 5 0.4 8 2.4 2/3 80 1.4 20 3000 1

ACPL-824-000E 300 mil DIP8 +/-50 20 300 1 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3

Quad Channel-16 pin ACPL-244-500E(Half pitch)

SO16 +/-50 20 400 1 5 0.4 8 2.4 2/3 80 1.4 20 3000 1

ACPL-844-000E 300 milDIP16

+/-50 20 300 1 5 0.2 20 1 4/3 70 1.4 20 5000 1/2/3

Notes:

1 - IEC/EN/DIN EN 60747-5-2/5 Option 060 available, 2 - 0.4 Lead Spacing Option W00 available, 3 - Gull Wing SMD option available

* CTR rank with Option 000E, 00AE, 00BE, 00CE, 00DE and 00LE available, # - CTR rank with option 000E, 00AE, 00BE, 00CE and 00DE available

@ CTR rank with Option 000E, 00BE and 00CE available

CTR rank with option 500E, 50AE, 50BE, 50CE and 50DE available,

CTR rank with option 500E, 50BE, 50CE

- CTR rank with option 500E and 50AE available.

Collector

Emitter

nodeCathode

nodeCathode

4

3

1

1 2 3 4

8 7 6 5

1 2 3 4

1 6 1 5 1 4 1 3

5 6 7 8

1 2 1 1 1 0 9

NEW

NEW

NEW

NEW

NEW


40/60

40


Solid State Relay (Photo MOSFET)

DescriptionAvago Technologies new ASSR Series arehigh-speed optically isolated MOSFET-output solid-state relays that featureperformance that has been qualified overa wide industrial temperature range of-40C to +85C. They are Form A (normallyopen) single-pole single-throw relays inindustry-standard 6-pin and 8-pin dual-in-line (DIP) packages, and 4-pin small outline(SO) packages. Their output ratings rangefrom 60V to 600V maximum load voltageand from 40mA to 2.5A continuous output

current. Their transient immunity of morethan 1kV/s and excellent noise rejectionbetween input-output as well as betweenopen terminals on the output will eliminateundesirable transient effects. Reinforcedinsulation of 3.75kV with fast switchingspeed makes them suitable for a wide rangeof industrial, consumer and automotiveapplications.

Compared to electromechanical relays,the ASSR Series offer distinct advantages,including the elimination of contact bounce,and problems due to shock, vibration, or

mounting position. They have no wearout mechanism limiting the number ofoperations, and require no minimumcontact wetting current. They are alsofree from magnetic fields, do not generateelectrical noise, and are not sensitive toelectromagnetic interference.

Benefits Superior to traditional electromechanical

relays (EMR)

Lower power consumption

Faster switching speed with hightransient immunity

Smaller size

Much better reliability

High reinforced insulation in miniatureSO-4 package

Qualied performance over- 40Cto +85C

Expanding portfolio to address diversiedmarket

Low R(ON )for less insertion loss

Low COFF)for better isolationperformance

High current capability with low R(ON)

General Purpose

The ASSR-14xx, ASSR-32xx and ASSR-41xxare designed for a wide variety of indus-trial and consumer electronics applica-

tions which includes telecommunicationsswitching, data communications, automaticmetering, medical system, security system,battery monitor, digital home appliances,set top boxes, etc.

Security Equipment Application Diagram

Applications

Telecommunicationsswitching

Data communications

Industrial control

Medical system

Security system

Automatic test equipment

Data acquisition system

Measuring instruments

EMR/reed relayreplacement

ASSR-xx20

Receiver / Alarm

Sensor / Detector Interface

ASSR-1218

Controller/Processor

Drive

Circuit

Sensor/Detector

(Motion,Sm

oke,

Light,etc.)

Sensor/Detector

(Motion,

Smoke,

Light,etc.)


41/60

41


Low C(OFF)R(ON)

The ASSR-xxxC and ASSR-xxxR Series arespecifically designed for fast switchingapplications, commonly found in test and

measurement applications such as pinelectronics, data acquisition, multiplexers

and matrix cards, and switching in theanalog circuits of parametric measurement

unit (PMUs). The low output capacitance,

low on-resistance, and low output off-stateleakage current of the ASSR Series provide

higher system throughput and reduce

system errors. In addition to their fastswitching speeds, the ASSR Series providereinforced insulation of 3.75kV, which is

often required in industrial environments.

High Current

The ASSR-15x0, ASSR-1611 and ASSR-5211

are specifically designed for high currentapplications, commonly found in the

industrial applications. In programmablecontrollers, input and output modules

allow microprocessors to sense and controlvarious loads. An AC output module allows

logic-level voltages to control a switch thatturns AC loads on and off. For example,

the output module of a process controllermight be used to cont

Optical Sensor Product Guide-Lr

Documents

Transcript of Optical Sensor Product Guide-Lr