Operation Manual - M-B Companies, Inc. c mb msv3 operator manu… · Operation Manual M-B...
Transcript of Operation Manual - M-B Companies, Inc. c mb msv3 operator manu… · Operation Manual M-B...
0615B
Operation ManualM-B Multi-Service Vehicle (MSV)
PN 904-183303
MSV DivisionM-B Companies, Incorporated
1615 Wisconsin AvenueNew Holstein, Wisconsin 53061
800.558.5800www.m-bco.com
MSV
M-B Multi-Service Vehicle • 2 • Table of Contents©2014 M-B Companies Inc. All Rights Reserved
Table of Contents
Safety ............................................................................. 7Hazard Definitions ..................................................... 7Identification of Safety Labels ................................... 7General Safety .......................................................... 8Pre-Start-Up Safety ................................................... 8Pressurized Systems Safety ..................................... 8The Manual ............................................................... 9Required Operator Training ....................................... 9Work Area .................................................................. 9Maintenance Safety ................................................... 9
General Information .....................................................10Introduction ................................................................10Machine Identification ................................................10Customer Service ......................................................10
Ballast Calculations .....................................................11Vehicle Information ......................................................12
Introduction ................................................................12
Operation ..................................................................... 13Introduction .............................................................. 13Operator Cab Controls ............................................ 13Steering Column ...................................................... 15Radio Console ......................................................... 16Circuit Breakers ....................................................... 16Heater Bypass ......................................................... 16Monitor Diagnose-Control (Plus+1®) ...................... 17Open Screen ........................................................... 17Main Menu Screen.. ................................................ 18Transport Mode Screen........................................... 19Transport Screen Icons............................................ 20Work Mode Screen .................................................. 21Work Mode Screen Icons......................................... 22Joystick Setup Screen..... ........................................ 23Front Input Screen ................................................... 24Front Output Screen ................................................ 25Front MVEC Screen ............... ................................. 26Calibration Screen.................................................... 27Attachment Selection Screen ................................... 28Password Screen..................................................... 30Rear Input Screen ................................................... 31Rear Output Screen ............................................... 32Rear MVEC Screen ................................................ 33Weight Transfer Screen ........................................... 34Faults Screens ......................................................... 35
Maintenance ................................................................
48Preventative Maintenance .......................................
48Replacement Parts / Warranty ...................................
49
Attachment Selections Examples ............................ 37Weight Transfer Example ....................................... 41Advanced Engine Diagnostics ................................. 43Joystick Layout ........................................................ 43Pre-Start Up ............................................................. 44Start Up Procedure .................................................. 44
Cold Weather Starting .............................................. 44Safety Link .............................................................. 45Front Attachment Connections ................................. 46Rear Hydraulic Connections..................................... 47
Quick Reference User Guide......................................... 3Quick Reference User Guide..................................... 3Quick Reference User Guide (remove)...................... 5
M-B Multi-Service Vehicle • 3 • Reference Guide©2014 M-B Companies Inc. All Rights Reserved
Quick Reference User Guide
Up - Aux 4ADown - Aux 4B
Shift Forward/ReverseThrottle Up/Down
Float mode On/O�
Aux 3A
Aux 3B
Forward - Front Hitch Down Backward - Front Hitch Up
Left - Aux 1ATrigger Up - Aux 2A
Right - Aux 1ATrigger Down - Aux 2B
Up - Aux 5ADown - Aux 5B
HOW TO START• Sit in seat, fasten seatbelt and insert key.• Turn key to ON. Wait for screen to display STARTUP (10 seconds).• Place foot on brake and turn key to START position.• Hold key in START position for a couple of seconds to start the engine.
If key is turned to START too soon, the tractor will not start. The key must then be reset by turning it to OFF - leave off for 5 seconds and then back to ON.
SHUTDOWN• Turn off PTO.• Turn off hydraulics.• Turn key to OFF and release
seatbelt to exit tractor.
PARKING BRAKE• Engages/Disengages
automatically when pressing and releasing accelerator pedal.
FORWARD/REVERSE• Using the joystick, push the
3rd toggle switch from the left UP for forward or DOWN for reverse.
THROTTLE (Work Mode)• Use the 2nd toggle switch
from the left on joystick to throttle UP (push upward) or to throttle DOWN (pull downward).
RAISE/LOWER FRONT ATTACHMENT
• While tractor is running, pull back on joystick to raise front attachment.
• Lower attachment by pushing forward on joystick.
ON/OFF REAR ELECTRICAL/HYDRAULIC ATTACHMENTS
• Turn rear electrical attachment (IE Sprayer) ON and OFF with 1st toggle switch on left.
• Turn rear hydraulic ON and OFF with 1st toggle switch on right.
Parking BrakeON/OFF
Switch between Work and
Transport mode
ForwardNeutralReverse
Right Turn Signal
Left Turn Signal
Headlight High Beam
Indicates Non-Critical Fault
Indicates Engine Fault
GREENwhen PTO engaged
M-B Multi-Service Vehicle • 5 • Reference Guide©2014 M-B Companies Inc. All Rights Reserved
Quick Reference User GuideThis page can be removed and kept in the operator’s cab.
Up - Aux 4ADown - Aux 4B
Shift Forward/ReverseThrottle Up/Down
Float mode On/O�
Aux 3A
Aux 3B
Forward - Front Hitch Down Backward - Front Hitch Up
Left - Aux 1ATrigger Up - Aux 2A
Right - Aux 1ATrigger Down - Aux 2B
Up - Aux 5ADown - Aux 5B
HOW TO START• Sit in seat, fasten seatbelt and insert key.• Turn key to ON. Wait for screen to display STARTUP (10 seconds).• Place foot on brake and turn key to START position.• Hold key in START position for a couple of seconds to start the engine.
If key is turned to START too soon, the tractor will not start. The key must then be reset by turning it to OFF - leave off for 5 seconds and then back to ON.
SHUTDOWN• Turn off PTO.• Turn off hydraulics.• Turn key to OFF and release
seatbelt to exit tractor.
PARKING BRAKE• Engages/Disengages
automatically when pressing and releasing accelerator pedal.
FORWARD/REVERSE• Using the joystick, push the
3rd toggle switch from the left UP for forward or DOWN for reverse.
THROTTLE (Work Mode)• Use the 2nd toggle switch
from the left on joystick to throttle UP (push upward) or to throttle DOWN (pull downward).
RAISE/LOWER FRONT ATTACHMENT
• While tractor is running, pull back on joystick to raise front attachment.
• Lower attachment by pushing forward on joystick.
ON/OFF REAR ELECTRICAL/HYDRAULIC ATTACHMENTS
• Turn rear electrical attachment (IE Sprayer) ON and OFF with 1st toggle switch on left.
• Turn rear hydraulic ON and OFF with 1st toggle switch on right.
Parking BrakeON/OFF
Switch between Work and
Transport mode
ForwardNeutralReverse
Right Turn Signal
Left Turn Signal
Headlight High Beam
Indicates Non-Critical Fault
Indicates Engine Fault
GREEN when PTO engaged
M-B Multi-Service Vehicle • 7 • Safety©2014 M-B Companies Inc. All Rights Reserved
WARNINGG�Read this manual and any attachment owner’s manuals before using this equipment. Failure to do so can result in serious injury or death. Call your dealer if you have any questions.
HAZARD DEFINITIONSFor your safety, and to assure the long life of your equipment, be sure you understand the following signal words which will be seen throughout this manual:
• DANGER: Alerts you to an immediate hazard, which will always result in severe personal injury and possible death if it is not avoided.
• WARNING: Alerts you to a hazard which will result in a serious personal injury or possible death in some cases, if not avoided.
• CAUTION: Alerts you to a potential hazard which may result in a serious personal injury if not avoided. It also alerts against an unsafe practice that will permanently damage equipment or property.
• IMPORTANT: Points out a proper use that will avoid damage to the machine, and/or will extend the life of its parts.
• NOTE: Suggests how to use or adjust the equipment for best product results.
IDENTIFICATION OF SAFETY LABELSSafety labels are strategically located around the vehicle to prevent potential hazards. The labels are a permanent part of the equipment. If they become separated from the product or illegible, contact M-B Companies Inc. for replacements. Understand the information the labels are communicating before operating or maintaining the equipment.
Avoid Abrupt Maneuversand Excessive Speed
Travel at Low SpeedWhen Turning
Always Wear Safety Belt
390-172409
WARNING: HIGHER ROLLOVER RISK
DANGER
HOT FLUID UNDERPRESSURE
390-152998
DANGER
CUTTING/SEVERING OFFINGERS OR HAND - FAN
390-152993
DANGER
390-157201
To prevent serious injury or deathfrom pinching:
• Keep all persons and objects clear while any part of this machine is in motion.
DANGER
ROTATING DRIVELINE HAZARDTo prevent serious injury or death fromrotating driveline:• Keep all guards in place when operating.• Keep hands, feet, hair and clothing away from moving parts. 390-157202
EMERGENCYPUSH TO STOPPULL TO RUN
390-134607
DANGER
DO NOT GO NEARHYDRAULIC OIL LEAKS
When checking for hydraulic systemleaks, observe only.
Never use your hands to check forleaks.
Hydraulic oil from a pin hole leakcan puncture your skin and causeserious injury, gangrene, or death.
If injured by hydraulic oil underpressure, seek medical attentionimmediately.
Oil can be hot and can cause severeburns.
390-152995
WARNING
Uneven terrain at higher speeds may cause vehicle to become unstable
390-157200
WARNING
HOT SURFACE390-152994
WARNING
NO RIDERS OR HANGERS ON
390-152996
Safety
M-B Multi-Service Vehicle • 8 • Safety©2014 M-B Companies Inc. All Rights Reserved
GENERAL SAFETY• This manual should be available during operation.• Extra copies of this manual are available for
purchase through M-B Customer Service.• To avoid serious injury or death, do not modify
equipment. Any modifications made to equipment can be dangerous and can void equipment warranty.
• Never defeat a safety device to make a task easier.• Never deface or remove factory-installed safety
labels. If a label ever becomes lost, damaged, or illegible, report this condition to a supervisor and obtain a replacement label from the Customer Service department of M-B Companies, Inc.
• Always wear proper apparel when operating equipment; safety glasses, face shield or goggles, ear protection, and dust mask. Tie hair back. Never wear loose clothing or jewelry that could get caught in moving parts.
• Never operate equipment with covers or guards removed. Rotating parts can cause severe injury. Keep hands, feet, hair, jewelry and clothing away from all moving parts.
• Understand the operation of hydraulic and pneumatic controls.
• Understand which adjustments are operator and which are maintenance adjustments.
• Always shut OFF equipment when left unattended.• Never operate or work around equipment if under
the influence of alcohol, drugs or medications.
Figure 1 • Always use the safety link whenever transporting
or performing work on the vehicle. Closing the safety link will prevent unexpected movement of the articulation joint.
WARNINGG�Batteries give off flammable fumes that can explode resulting in personal injury.Electrolyte is an acid and can cause personal injury if it contacts skin or eyes.
PRE-START-UP SAFETY• Install any covers or guards which may have been
removed for shipping purposes or maintenance.• Before starting equipment, walk around equipment,
making a visual inspection that all safety devices are properly installed and secured.
• Check that all hardware, fasteners, hydraulic fittings, etc. are in good condition and properly fastened. Replace any fatigued or damaged items with proper replacements.
• Personnel who are not required to be in the work area should be kept away. Never start the equipment unless you are absolutely certain that everyone in the area is clear of the machine and aware it is being started.
• Follow the manufacturer’s recommended start-up procedure.
PRESSURIZED SYSTEMS SAFETY• Do not disassemble a pressurized system unless
properly trained and equipped with adequate tooling.
• Familiarize yourself with the proper method of relieving pressure from pneumatic or hydraulic systems. Never perform maintenance on, or disassemble, pressurized systems without first locking out power to these systems and then relieving pressure to them.
• Oils and fluids can be very hot under pressure. Use caution and allow the system to cool before beginning maintenance work.
• Never operate or pressurize one of these systems with worn or damaged components. Replace hoses, fittings, valves or other components which appear defective.
• Never adjust pressurized systems beyond recommended levels to achieve higher operating pressures.
M-B Multi-Service Vehicle • 9 • Safety©2014 M-B Companies Inc. All Rights Reserved
THE MANUALIt is the purpose of this manual to provide complete instructions for the operation of the M-B Multi-Service Vehicle.
Directional ReferenceAll reference to left, right, front, or rear are given from the operator in the operator position and facing the direction of your unit.
REQUIRED OPERATOR TRAININGOriginal purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by someone other than original purchaser; loaned, rented or sold, ALWAYS provide this manual and any needed safety training before operation.The Operator Must Understand:
• How to operate all controls• The functions of all controls• How to STOP in an Emergency• Speed Ranges
WORK AREA• ALWAYS check overhead and side clearances
carefully before operation. ALWAYS be aware of traffic when operating along streets and curbs.
• Keep area of operation clear. Stay alert for hidden hazards.
• DO NOT run engine in an enclosed area. Always provide good ventilation.
• Abnormal Vibrations are a warning of trouble. Striking a foreign object can damage unit. Stop unit and engine. Wait for all moving parts to stop. Inspect unit and make any necessary repairs before restart.
• Protect eyes, face, and head from objects that may be thrown from unit. Wear appropriate hearing protection.
• Avoid Sharp Edges. Sharp edges can cause serious injury. Wear gloves to service unit when handling sharp edges.
• ALWAYS keep hands and feet away from all moving parts during operation. Moving parts can cause serious injury or death.
• Be aware of the surroundings. Look for blind spots from which pedestrians or vehicles may suddenly appear.
• Locate the emergency stop on the vehicle.• Do not operate in crowded pedestrian areas. This
equipment may cause serious injury or death if safety rules are not followed.
• The M-B Multiple Service Vehicle (M-B MSV) uses a level gauge. The gauge helps the operator determine the angle or slope of the surface being driven on. The gauge shows percent of grade.
WARNINGG�During normal operation the M-B MSV must not exceed 30% grade to either side. Adding any attachment to the M-B MSV will affect the safe maximum grade.
Figure 2
MAINTENANCE SAFETY• Do not remove guards while operating. After
maintenance work, be sure all guards and other safety devices are installed and in proper working order.
• Never clean, lubricate, or adjust equipment while it is moving, has the potential to move or when engine is running.
• Always release pressure from pressurized systems before disassembling.
• Allow ample time for heated components to cool before working on or working close to them. Use temperature sticks or other appropriate devices to test temperatures.
• ALWAYS maintain unit in safe operation condition.• Check the conditions of the unit at the end of each
day and repair any damage or defects.• Keep all fasteners properly torqued and in safe
operating condition.• Before maintenance, adjustments, or service
(except where specifically recommended), shut off engine, and secure from moving.
StorageALWAYS clean and lubricate equipment before extended storage. Disconnect the battery cables. Clean and lubricate equipment every 6 months during prolonged storage.
M-B Multi-Service Vehicle • 10 • General Information©2014 M-B Companies Inc. All Rights Reserved
INTRODUCTIONThank you for choosing M-B Companies, Inc. as your equipment manufacturer and supplier. As part of our commitment to total customer satisfaction, we have strived to ensure that the information contained within this manual is complete and representative of the equipment you have purchased. The manual cannot, however, anticipate every possible contingency to be met in the installation, operation and maintenance for your equipment. If you require additional information not included in this manual, please contact our Service Department at:
Customer Service Department c/o M-B Companies, Inc.
1615 Wisconsin Ave. PO Box 200
New Holstein, WI 53061 Phone: 1-888-558-5801 or 1-800-558-5800
Fax: 920-898-4588
MACHINE IDENTIFICATIONEach machine manufactured by M-B Companies, Inc. has an identification plate mounted to it as shown in Figure 3. This plate contains the serial number of your M-B equipment. Copy the information from the plate on your equipment into the appropriate space in Figure 3. This information is important to have available when communicating with M-B.
Vehicle Certification Label
Figure 3
CUSTOMER SERVICEThe serial number on your equipment is essential for proper service support. When contacting M-B Companies regarding service support, always provide the product serial number. This number is located on the identification plate mounted on your equipment, and should also have been recorded in the Machine Identification section.
Customer Service Department c/o M-B Companies, Inc.
1615 Wisconsin Ave. PO Box 200
New Holstein, WI 53061 Phone: 1-888-558-5801 or 1-800-558-5800
Fax: 920-898-4588
General Information
M-B Multi-Service Vehicle • 11 • Ballast Calculations©2014 M-B Companies Inc. All Rights Reserved
Ballast CalculationsBallast Calculations Adding Attachments will affect the stability, performance, characteristics, and reduces safe operating grades. Never exceed the max rating of the weakest component: GVWR, max axle ratings, or tire capacity. Never operate with less than 25% of the total load on the front axle. All calculations should be verified by weighing the MSV with the attachments on a certified scale. Attachments such as sanders and sprayers should be checked when filled with desired particulate. A scale must be used to determine axle weights when using a dump body. Ballast Types include: Fluid filled tires, wheel weights, or another attachment.
NOTE: All weights in pounds; all dimensions in inches. CW= Curb Weight for MSV-100501; 6620 lbs, Front-2140 lbs, Rear-4480 lbs TW =FA+RA including attachments and or ballast. WB = Wheel Base; 81in for MSV TFA= Total Front Axle Weight TRA= Total Rear Axle Weight CgF= Weight at the center of gravity of front attachment or ballast CgR= Weight at the center of gravity of rear attachment or ballast FA = Front Axle RA = Rear Axle dF = dimension from center of front axle to Center of gravity on front attachment or ballast dR = dimension from center of rear axle to Center of gravity on rear attachment or ballast
If unsure of calculations, contact M-B Customer Support 1-800-558-5800
M-B Multi-Service Vehicle • 12 • Vehicle Information©2014 M-B Companies Inc. All Rights Reserved
INTRODUCTIONThis section provides information that is specific to the M-B MSV. Each sub-section describes a component or system to give the reader a reasonable understanding of the topic. If a more in-depth knowledge is needed, contact M-B Companies Customer Support.
Vehicle Information
M-B Multi-Service Vehicle • 13 • Operation©2014 M-B Companies Inc. All Rights Reserved
INTRODUCTIONThis section of the manual describes the function of the controls typically provided with the MSV. Because of the unique and complex nature of this equipment, this document may not be an exact representation of the controls on your equipment.Controls which are not part of the standard or optional M-B controls package, but which are unique to an individual attachment may not be listed. Separate manuals are created for attachments.M-B Companies Inc. reserves the right to modify the function or location of the operator controls. Please call our Customer Service Department before operating the machinery if you have any questions regarding the controls on your MSV.
OPERATOR CAB CONTROLSThe operator cab has several controls that are used to operate the M-B MSV. This section details the controls that the operator uses to provide comfort and safety. The joystick and the Plus+1® interface are described in another section.
Operator SeatThe seat is cushioned by an airbag that absorbs bumps and vibration. The firmness of the cushion is adjusted using a knob located at the front of the seat and below the operators legs (Figure 4).
Adjust Seat Air Cushion
Seat Back
Forward/Back
Figure 4
With the engine running, the firmness is adjusted by rotating the knob up for firmer or down for less firm. When the engine is off rotating the knob down releases air.Two levers on the side of the seat control forward/back and seat back position.Move the front lever to release the seat and move the seat to the new position. Release the lever to lock.Lift the rear lever to release the seat back. Reposition the seat back and release the lever to lock.The cab also has a cup holder, document storage compartments and a flip down armrest (Figure 5).
Document Storage
Cup Holder
Flip Down Armrest
Figure 5
Air VentsThere are several air vents throughout the cab. The vents can be rotated and the blades move to direct airflow (Figure 6).
Rotating Ring
Figure 6
Operation
M-B Multi-Service Vehicle • 14 • Operation©2014 M-B Companies Inc. All Rights Reserved
SunroofThe sunroof can be opened by flipping the rear latch and pushing up on the back half of the window (Figure 7).
Figure 7 The window can be removed completely. The two front latches are opened by pulling down on the center piece (Figure 8).
Clip Open
Figure 8 Open the rear latch. Pull down sharply on the end attached to the roof. The latch will pull free from the connection leaving the post (Figure 9).
Figure 9 Remove the window and store in a safe place.
To replace the window, position it on top of the opening seal.
CAUTIONG�The seal must be in proper location or it will leak.
Move the latches into position. Secure the front two by snapping the levers into the hinge point. The rear latch should be positioned so the open clip is over the post. Then push that end onto the post. Open the window and inspect the seal. The front edge of the window must lay flat on the seal (Figure 10).
Seal Correct
Seal Pushed Out
Figure 10 With the window open the seal can be pulled into position.
M-B Multi-Service Vehicle • 15 • Operation©2014 M-B Companies Inc. All Rights Reserved
STEERING COLUMNSeveral controls are located on the steering column. The left side has controls for; windshield squirter, horn, wiper, headlight high beams and the steering wheel tilt (Figure 11).The right side and the top end of the column have controls for; fan, keyswitch, lights, hazard lights and air conditioning (Figure 11).
Key SwitchVery similar to an automotive key switch, there are three positions; OFF, ON, and START. When the key switch is OFF, all vehicle functions except the horn are off. After the engine is started the keyswitch releases to ON (run).IMPORTANTG� The engine will not start unless Plus+1®
is ready. Turn the key to ON and wait for Plus+1® to start up (approximately 15 seconds). If the key is turned to START before Plus+1® is ready, the key must be reset. Turn the key to OFF, wait 5 seconds, then back to ON. When Plus+1® is ready the engine preheater will be ready. The engine can then be started.
To start the engine the operator must be in the seat and the seat belt must be fastened. The Plus+1® must be showing the main operating screen.
Windshield SquirterThe ring at the end of the lever activates the windshield squirter. Press in on the ring. Washer fluid will be pumped as long as the ring is pressed. The wipers will start moving then stop when the ring is pressed. See Figure 11.
HornThe horn will work regardless of the key switch position. Press in on the button at the end of the lever. See Figure 11.
WiperRotating the barrel of the lever will activate the wipers. From the off position rotate the barrel up (clockwise) one notch for low speed. Rotate two notches for high speed wipers. Rotate the barrel down (counterclockwise) for intermittent wipers. See Figure 11.
Headlight High BeamsWhen the headlights are on, push down on the lever to change between low and high beam settings. See Figure 11.
FanThe fan pulls air through the filter cartridge and into the cab. Rotating vents distribute the air. The switch has four positions; OFF, LOW, MEDIUM, and HIGH. See Figure 11.
Push outer ring for windshield washer
Steering Column Tilt/Telescope
Air Conditioning: Off On
Key Switch: Off On Start
Fan: Off Low
Medium High
Hazard Flashers: Off On
Exterior Lights: Off Running Headlights
Rotate for Wipers: High
Low Off Intermittent
Push center for horn
Push down for headlight
high beams
Figure 11
M-B Multi-Service Vehicle • 16 • Operation©2014 M-B Companies Inc. All Rights Reserved
Steering Column Tilt/TelescopeThe steering column can be tilted and telescoped toward or away from the operator. Hold the steering wheel with one hand. Move the lever to unlock. Tilt or telescope the steering column to a comfortable position. Release the lever to lock the column in the new position. See Figure 11.
SwitchesThere are switches for the exterior lights, hazard flashers and air conditioning. These rocker switches are located at the top of the steering column. See Figure 11.
• Air Conditioning - On/Off• Hazard Flashers - On/Off
When the lights are flashing, the turn signal arrows on the Plus+1® display will flash.
• Exterior Lights - Off/Running/Headlights When the switch is moved to a position it will stay until it is pushed again.
RADIO CONSOLEThe radio is on the right side of the steering column. Another feature is a 12 volt 10 amp power point socket. It is similar to an automotive outlet where accessories can be plugged in. See Figure 12.
Accessory Plug-in12 volt10 amp
Figure 12
CIRCUIT BREAKERSLocated under the right armrest are push-to-reset circuit breakers (Figure 13).If a circuit breaker trips or trips repeatedly, maintenance personnel should be notified. A circuit breaker that needs to be reset more than once is an indication of an electrical problem that requires repair.
Figure 13
HEATER BYPASSIn front of the joystick is an adjustment for bypassing the heater. When this knob is rotated the temperature of incoming air is raised or lowered. Opening the valve increases heat.IMPORTANTG� This adjustment should be closed
when the air conditioning is on.
Figure 14
M-B Multi-Service Vehicle • 17 • Operation©2014 M-B Companies Inc. All Rights Reserved
Open Screen
Operation - Plus+1® Controls
M-B Multi-Service Vehicle • 18 • Operation©2014 M-B Companies Inc. All Rights Reserved
Main Menu Screen
Button Function
Access Transport Mode (Refer to Page 19 )
Access Work Mode (Refer to Page 21 )
Access Joystick Setup (Refer to Page 23)
Access Front Inputs, Outputs, and MVEC Status Screens - Use Up and Down arrows to access each section (Refer to Pages 24-26)
Access Calibration Screen (Refer to Page 27)
Access Attachment Selection Screen (Refer to Pages 28-29)
Access Password Screen - If showing “PW OK” Password access has be granted (Refer to Page 30)
Access Rear Inputs, Outputs, and MVEC Status Screens - Use Up and Down arrows to access each section (Refer to Page 31-33)
Up and Down arrow keys will cycle through the screen functions as well.
2
3
4
5
6
7
8
1
M-B Multi-Service Vehicle • 19 • Operation©2014 M-B Companies Inc. All Rights Reserved
Transport Mode Screen
Button Function
Turns on cruise control function of MSV. To engage cruise control press “OK”. To disengage press brake pedal or “OK” button again. To return to foot pedal throttle (FP Throttle) arrow down. Pressing okay will activate joystick throttle control.
Actives low speed, pressing again will return to high speed mode
Access to faults screens (Refer to page #)
Brings MSV to idle. Pressing again brings MSV back to last RPM level
Access to work screen mode – may have to reduce speed
NOT USED
Returns to Main Menu
Activates beacon light controls. Pressing “OK” turn on/off beacon light.Arrow down again to access rear work light controls. Pressing “OK” will turn on /off the rear work lights, if equipped.
3
4
5
6
7
8
2
Icons in uppers left corner of screen will light up red when a warning has occurred. A beep with occur every minute when a warning light is illuminated.
M-B Multi-Service Vehicle • 20 • Operation©2014 M-B Companies Inc. All Rights Reserved
Left Signal Indicator Low Fuel Warning
High Engine Temperature
Service Hydraulic Filter
Oil Pressure Warning
Low Batttery Voltage
High Hydraulic Oil Temperature
Parking Break Engaged
Seat Belt
Engine Fault
System Faults
System receiving signal fromengine ECM
Fuel Gauge
Engine Coolant Guage
Engine Oil Gauge
Low Battery Gauge
Hydraulic Oil
Current horsepower load being used by engine
Right Signal Indicator
Vehicle Drive Status
Headlight High Beam Indicator
Hour Meter
Alarms Display
Engine RPM
Vehicle Speed
Glow Plugs
Main Menu
Cruise
Foot Pedal Throttle
Hi/Low Range Selection
Lights - select to turn on
Indicates when in High Speed
Quick Stop - Quick Idle
Vehicle Ground Drive
Operator is present
Transport Screen Icons
M-B Multi-Service Vehicle • 21 • Operation©2014 M-B Companies Inc. All Rights Reserved
Work Mode Screen
Button Function
Press to select creep mode, press “OK” to engage creep mode. Utilize creep mode to connect attachments.Press again to select diff lock mode, press “OK” to engage. Diff lock is used to reduce wheel slippage, use only under 7 MPH.
Turns on cruise control function of MSV. To engage cruise control press “OK”. To disengage press brake pedal or “OK” button again.Press again to activate foot pedal throttle, press “OK” to engage
Energizes PTO icon. Press “OK” to activate PTO icon. MSV must be under 1200 RPM to activate
Access to faults screens (Refer to pages 35-36)
Brings MSV to idle. Turns off any attachment. Pressing again will return MSV to previous RPM and turn back on the attachments that were previously on.
Access to transportation screen mode
Access to weight transfer setup screen. Must have weight transfer function selected.(Refer to page 34)
Returns to Main Menu
Activates beacon light controls. Pressing “OK” turn on/off beacon light. Arrow down against to access rear work light controls. Pressing “OK” will turn on /off the rear work lights, if equipped.Arrow down again to active weight transfer function (Refer to page 34)
2
3
4
5
6
7
8
1
M-B Multi-Service Vehicle • 22 • Operation©2014 M-B Companies Inc. All Rights Reserved
Left Signal Indicator
Parking Break Engaged
Seat Belt connected (green)
Seat Belt not connected
Engine Fault
System Faults
Current horsepower load being used by engine
Right Signal Indicator
Vehicle Drive Status
Headlight High Beam Indicator
Alarms Display
Engine RPM
Vehicle Speed
Creep Mode ON (green)
Diff lock engaged (green)
Main Menu
Pressure level to ground drive
Cruise engaged (green)
Foot Pedal Throttle active (green)
PTO RPM
PTO engaged (green)
Amount of weight on front hitch
Lights - select to turn on (green)
Weight Transfer engaged (green)
Adjustment for Weight Transfer
Function being operated by joystick
Current front and rear attachment selection
Quick Stop - Quick Idle
Vehicle Ground Drive
Spray/Spreader on (green)Speader Speed 0-6
Setup Weight Transfer
Aux 3A on (green)
Hitch in Float Mode (green)
Voltage
Fuel Level
Speed too high. Switch to Work Mode. Must stop to switch modes.
Work Screen Icons
M-B Multi-Service Vehicle • 23 • Operation©2014 M-B Companies Inc. All Rights Reserved
Joystick Setup Screen
Button Function
Returns to Main Menu
Cycle through each function. Press “OK” to select function. Press up/down again to place the position of the function. Function must not be active on other selections. Place NA on the functions you do not want to use. Functions 3, 4, 5 and 6 cannot be moved.
8
The numbers on the left side of each function are the default numbers. Place the number in the right to set back factory default. Functions 19, 20, and 21 are bonus functions that must be assigned an unused number.
M-B Multi-Service Vehicle • 24 • Operation©2014 M-B Companies Inc. All Rights Reserved
Front Input Screen
Button Function
Returns to Main Menu
Press to highlight Front Inputs
Cycle through Front Inputs, Outputs and MVEC
Press to access highlighted option
8
Displays the status of the front inputs.
OK
4
M-B Multi-Service Vehicle • 25 • Operation©2014 M-B Companies Inc. All Rights Reserved
Front Output Screen
Displays the status of the front ouptuts and what voltage or current it is modulating.
Button Function
Returns to Main Menu
Press to highlight Front Inputs
Cycle through Front Inputs, Outputs and MVEC
Press to access highlighted option
8
OK
4
M-B Multi-Service Vehicle • 26 • Operation©2014 M-B Companies Inc. All Rights Reserved
Front MVEC Screen
Displays the status of the front MVEC.
Button Function
Returns to Main Menu
Press to highlight Front Inputs
Cycle through Front Inputs, Outputs and MVEC
Press to access highlighted option
8
OK
4
M-B Multi-Service Vehicle • 27 • Operation©2014 M-B Companies Inc. All Rights Reserved
Button Function
Resets foot pedal settings. Allows you to recalibrate foot pedal
Resets hydraulic filter notice
Cycles between slow, medium and high ground drive ramping
Cycles between slow, medium and high ground drive ramping
Resets steering cylinders
Returns to Main Menu
Change screen brightness
Change tire size
2
3
4
5
8
1
Calibration Screen
M-B Multi-Service Vehicle • 28 • Operation©2014 M-B Companies Inc. All Rights Reserved
Button Function
Front attachment selectionArrow up/down to cycle through attachments. Press and hold “OK” for three seconds to select attachment
Press and hold to reset front attachment
Rear attachments selectionArrow up/down to cycle through attachments. Press and hold “OK” for three seconds to select attachment
Press and hold to reset rear attachment
Access attachment setup screen. This function is only accessible with password clearance from the main menu screen.
Returns to Main Menu
2
5
6
7
8
1
Each selection illuminate in red when a fault is registered.
Attachment Selection Screen
M-B Multi-Service Vehicle • 29 • Operation©2014 M-B Companies Inc. All Rights Reserved
Once you have your attachment selected on the attachment selection screen you can access the attachment setup screen only with password clearance from the main menu screen.
Attachment Selection Screen
M-B Multi-Service Vehicle • 30 • Operation©2014 M-B Companies Inc. All Rights Reserved
Button Function
#1
#2
#3
#4
#5
#6
#9
#0
Submit Password
Returns to Main Menu
2
3
6
7
8
OK
esc
1
Only accessible when password has been provided by M-B
Password Screen
M-B Multi-Service Vehicle • 31 • Operation©2014 M-B Companies Inc. All Rights Reserved
Displays the status of the rear input and frequency.
Button Function
Returns to Main Menu
Press to highlight Rear Inputs
Cycle through Rear Inputs, Outputs and MVEC
Press to access highlighted option
8
OK
4
Rear Input Screen
M-B Multi-Service Vehicle • 32 • Operation©2014 M-B Companies Inc. All Rights Reserved
Displays the status of the rear output and frequency.
Button Function
Returns to Main Menu
Press to highlight Rear Inputs
Cycle through Rear Inputs, Outputs and MVEC
Press to access highlighted option
8
OK
4
Rear Output Screen
M-B Multi-Service Vehicle • 33 • Operation©2014 M-B Companies Inc. All Rights Reserved
Displays the status of the rear MVEC.
Button Function
Returns to Main Menu
Press to highlight Rear Inputs
Cycle through Rear Inputs, Outputs and MVEC
Press to access highlighted option
8
OK
4
Rear MVEC Screen
M-B Multi-Service Vehicle • 34 • Operation©2014 M-B Companies Inc. All Rights Reserved
Button Function
Reset weight transfer configuration by holding for two seconds
Save settings
Return to work mode screen
Decrease weight transfer
Increase weight transfer
2
3
1
Weight Transfer Screen
M-B Multi-Service Vehicle • 35 • Operation©2014 M-B Companies Inc. All Rights Reserved
Button Function
Access to Engine Faults
Access to Front MVEC Faults
Access to Front Control Faults
Access to Rear MVEC Faults
Access to Rear Control Faults
Access to Return to Main Menu
2
3
6
7
8
1
Faults Screen
M-B Multi-Service Vehicle • 36 • Operation©2014 M-B Companies Inc. All Rights Reserved
Rear Control Faults ScreenWhen highlighted in RED shows an active fault
Front Control Faults ScreenWhen highlighted in RED shows an active fault
Front MVEC Faults ScreenWhen highlighted in RED shows an active fault
Rear MVEC Faults ScreenWhen highlighted in RED shows an active fault
Faults Screens
M-B Multi-Service Vehicle • 37 • Operation©2014 M-B Companies Inc. All Rights Reserved
The following examples apply once the initial attachment setup has been performed by M-B or a factory trained MSV dealer.This setup includes adjusting outputs to the optimum levels.
Selecting the Ribbon Snow Blower AttachmentConnect the Ribbon Snow Blower and the hydraulic hoses to the desired auxiliary hydraulics.
Operation - Attachment Selection Examples
Button Function
Attachment Selection screen6
Button Function
Press and hold for two seconds to reset front attachment
Front attachment selection
Press two times to highlight MSV PTO Ribbon Blower
Press and hold for three seconds to set attachment
Return to Main Menu
2
8
OK
1
M-B Multi-Service Vehicle • 38 • Operation©2014 M-B Companies Inc. All Rights Reserved
Selecting the Ribbon Snow Blower attachment (continued)
Button Function
Enter Work Mode2
Button Function
Select PTO, Engine RPM must be below 1200 RPM to activate PTO.
Press “OK” to use PTO (engages Impeller), PTO RPM shows above PTO icon. Increase PTO RPM’s by increasing engine RPM’s.
User Defined Press user defined button on joystick to turn on Aux 3A function to engage ribbon.
3
OK
Increase engine RPM to desired speeds and begin using attachments.
M-B Multi-Service Vehicle • 39 • Operation©2014 M-B Companies Inc. All Rights Reserved
The following examples apply once the initial attachment setup has been performed by M-B or a factory trained MSV dealer.This setup includes adjusting outputs to the optimum levels.
Selecting the Rear Spreader AttachmentConnect the Rear Spreader and the hydraulic hoses.
Operation - Attachment Selection Examples
Button Function
Attachment Selection screen6
Button Function
Press and hold for two seconds to reset rear attachment
Rear attachment selection
Press three times to highlight MSV Spreader
Press and hold for three seconds to set attachment
Return to Main Menu
6
8
OK
5
M-B Multi-Service Vehicle • 40 • Operation©2014 M-B Companies Inc. All Rights Reserved
Selecting the Rear Spreader Attachment (continued)
Button Function
Enter Work Mode
Button Function
User Defined Press user defined button to engage Aux 4A to turn on rear spreader.
2
Increase engine RPM to desired speeds and begin using attachments.
M-B Multi-Service Vehicle • 41 • Operation©2014 M-B Companies Inc. All Rights Reserved
The following examples apply once the initial attachment setup has been performed by M-B or a factory trained MSV dealer.This setup includes adjusting outputs to the optimum levels.
Initial set up of the Weight Transfer featureAfter your attachments are connected and set up follow these steps. Steps need to be done when switching between attachments.
Operation - Weight Transfer Example
Button Function
Work mode screen2
Button Function
Arrow down three times
Press “OK” to turn on Weight Transfer
Access Weight Transfer setup screen7
OK
M-B Multi-Service Vehicle • 42 • Operation©2014 M-B Companies Inc. All Rights Reserved
Initial set up of the Weight Transfer feature (continued)
Button Function
Decrease weight transfer (decreases weight on front wheels)
Increase weight transfer (increases weight on front wheels)
Increase engine RPM to desired speeds and begin using attachments.
Button Function
Hold for two seconds to reset weight transfer
Joystick Forward Push joystick forward to activate weight transfer
Press multiple times until attachment begins to raise
Press until attachment stops rising. This sets 100% of the attachment weight on the hitch.
Press to save settings
Return to Work Mode screen
1
2
3
M-B Multi-Service Vehicle • 43 • Operation©2014 M-B Companies Inc. All Rights Reserved
ADVANCED ENGINE DIAGNOSTICSThe engine has diagnostic information that can be viewed using the Plus+1® displays. The engine manufacturer provides a second level of diagnostic information. Refer to the engine documentation for hardware requirements and access to that level. The communication port is located below the right side arm rest (Figure 35).
Diagnostic Port
Figure 35
JOYSTICK LAYOUTThe Joystick Layout screen is used to display all current joystick functions. Some functions will change depending on the Attachments selected. The layout shown results when None is selected in the Attachment Selection screen.
Up - Aux 4ADown - Aux 4B
Shift Forward/ReverseThrottle Up/Down
Float mode On/O�
Aux 3A
Aux 3B
Forward - Front Hitch Down Backward - Front Hitch Up
Left - Aux 1ATrigger Up - Aux 2A
Right - Aux 1ATrigger Down - Aux 2B
Up - Aux 5ADown - Aux 5B
Figure 36
Operation
M-B Multi-Service Vehicle • 44 • Operation©2014 M-B Companies Inc. All Rights Reserved
PRE-START UPWARNINGG�
Before performing any of the following inspections, make sure that the vehicle engine is shut down, the ignition key is removed, and all personnel in the work area are aware that the equipment is being inspected and must not be started.Never check for hydraulic leaks by hand. Hydraulic fluid under pressure can penetrate skin.
Inspect all hydraulic lines for evidence of leaking, loose fittings, and frayed or damaged hoses.Check hydraulic cylinders for broken or loose parts, especially cotter pins on the hydraulic cylinders.Check the hydraulic oil level. A sight gauge is located on the side of the reservoir for this purpose. Add fluid as necessary.
All access doors are secured in place.
Visually inspect for fluid leaks under the vehicle.
Check engine fluids.
Check for faults on screen.
Inspect attachments for damage and proper connection.
START-UP PROCEDURE
Key SwitchThe key switch on the steering column is used to initialize Plus+1® controller and start the engine. The engine will not start until Plus+1® has booted up and the intake manifold heater has properly warmed.To start the MSV the operator must be seated. Turn the key switch to the on position. Watch the screen of Plus+1®. After an M-B splash screen the start up screen will appear. Turn the key to start the engine.IMPORTANTG� The engine will not start unless
Plus+1® is ready. Turn the key to ON and wait for Plus+1® to start up (approximately 15 seconds). If the key is turned to START before Plus+1® is ready, the key must be reset. Turn the key to OFF and back to ON. When Plus+1® is ready the engine preheater will be ready. The engine can then be started.
Trying to start the engine prior to the Startup screen appearing may cause delays. Engine will not crank until manifold heater is at starting temperature. Colder temps will cause delays. 1. Start the engine.2. Use Plus+1® to determine if the correct attachments
are configured in the controls3. With the engine idling, operate the attachments until
the system warms up.4. Return to the main screen for operation.
COLD WEATHER STARTING
Before Starting the EngineNOTEG� Do not use a torch to heat a compartment.
This causes fires, burns wiring, gaskets and seals, or melts protective plastic. When using canvas covers, do not install them near exhaust systems. This helps to prevent fires.
Manually Sprayed Ether Starting Aids
DANGERG�Do not use manually sprayed Ether starting aids. Using a spray type starting aid may cause the air intake to explode and cause personal injury.
Intake Air HeaterThe engine has a grid heater in the air intake tube just before the intake manifold. This heater is controlled as needed by the engine electronics. Do not bypass or force the heater on.
M-B Multi-Service Vehicle • 45 • Operation©2014 M-B Companies Inc. All Rights Reserved
AFTER STARTING ENGINEWhenever a machine has been parked for a long period of time, some of the systems will cool to below normal operating temperatures. Always warm the machine systems before operating the machine at full operationDamage to engine valve control components can result from engine operation for short intervals during operation in very cold weather conditions. If the engine is not allowed to warm completely, the engine can be damaged by repeated starting and stopping.To avoid damage, always run the engine until the coolant temperature is at least 180°F (82°C).After the engine is warm, warm up the other systems. Start with the hydraulics. Run the engine at less than one-third throttle, and slowly move the control lever to lift the attachment. Initially, lift the control lever for a few inches (centimeters). Lower the attachment slowly. Continue the sequence: raising, lowering, extending, and retracting. Extend the travel during each cycle. Perform this operation for all hydraulic circuits. Alternate between all of the attachments.Exercise the transmission and the power train. If you cannot move the control for the transmission, perform the following steps:
• Engage the parking brake or apply the brake pedal.• Run the engine slightly above LOW IDLE.• Shift the transmission several times from
FORWARD to REVERSE.Release the brake. Move the equipment forward and backward for several feet (meters). Exercise the machine for several minutes.To reduce the total warm up time, start exercising the entire machine before you complete the hydraulic warm up time.Operate under light load until the systems reach normal operating temperatures.If the engine temperature is not high enough enclose the engine and block the radiator. A thermostat that opens at a higher temperature will not increase the engine temperature if the engine is not under load.To prevent seal damage and gasket damage, keep the engine crankcase breather pipe clear of blockage.In extreme conditions, use a canvas over the engine compartment. Heat the engine area with a space heater. This will aid in starting the engine. Extending the canvas over the hydraulic components will provide initial warming of the components.
Multigrade lubricants (10W30) may be used successfully at ambient temperatures below the pour point of the oil. However, in order to use this oil, you must leave the engine running at low idle. This helps keep lubricants and compartments warm for the engine and for the transmission. Running the engine at low idle will not keep the hydraulic systems warm.
SAFETY LINKThe chassis for the MSV articulates or pivots in the middle. This is used to help maneuver the MSV and provides a smaller turning radius.During maintenance it is advisable to lock-out the articulation of the chassis.To lock the Chassis:1. Pull straight ahead to align the chassis.2. Locate the safety link on the frame behind the cab
(Figure 37 Safety Link Open).3. Pull out the removable pin (Figure 38).4. Swing the link to meet the back half and insert the
pin.When the safety link is not in use, it should be stored against the front frame.
Removable Pin
Safety Link
Figure 37 Safety Link Open
Figure 38
M-B Multi-Service Vehicle • 46 • Operation©2014 M-B Companies Inc. All Rights Reserved
FRONT ATTACHMENT CONNECTIONS
Front Hitch ConnectionsIMPORTANTG� For best performance each
attachment must be setup by M-B or your authorized MSV dealer prior to use.
The attachment hitch has two hooks with hitch clamps. Up and down movement is supplied by two hydraulic cylinders.The hitch hooks will slide side-to-side to align with various attachments.
CAUTIONG�If the attachment is not centered on the vehicle damage may occur. Keep the hitch hooks tightened in place. The hydraulic hoses must be kept clear from all interference points.
Clamp Lock
Hook
Locking Bolt
Lock Pin
Open
Figure 39To connect an attachment:1. Pull the MSV close to the attachment.2. Adjust the hooks side-to-side as needed using the
locking bolt on the back side. Pull the handle forward to open the clamp locks.
3. Drive the MSV forward with the hooks lowered. Putting the MSV in Creep Mode will assist in this.
4. The hooks should fit into the arms of the attachment. Lift the hitch in position so the hooks engage and lift the attachment.
5. Push the clamp locks back completely. 6. Insert the safety pins. Most attachments will have
a top link as a third connecting point. This link is normally used to level the attachment.
Some attachments may be different. Review the instructions with each attachment. Hydraulic, PTO, and electrical connections may also be needed for proper attachment use.
Front Power Take Off (PTO)The front attachment PTO is accessed thru a panel under the operators feet (Figure 40).
WARNINGG�Turn the engine off before opening the access panel.
Remove the panel.
PTO Access Panel
Figure 40The drive spline is visibleNOTEG� The spline (Figure 41) should have a coating
of grease before attaching the PTO shaft.
Drive Spline
Locking Groove
Figure 41The PTO shaft is inserted from the front of the MSV (Figure 42).Line the universal joint up with the spline and push together. Make sure the locking device or universal joint has compressed in groove of PTO shaft (Figure 43).
PTO Shaft
Figure 42
M-B Multi-Service Vehicle • 47 • Operation©2014 M-B Companies Inc. All Rights Reserved
PTO Spline
Universal Joint of PTO Shaft
Figure 43Replace the access panel before starting the engine.
Hydraulic ConnectionsAt the front of the MSV there are three pair of connections. Each pair has a line out and a line in. The connections are matched for each pair. Attachments are connected and Plus+1® controls are set to control the proper auxiliary ports. See Attachment Manual for proper connections. Also refer to Plus+1® Controls section in this manual.
Aux 1B Quick Disconnect
Aux 1A Quick Disconnect
Aux 2B Quick Disconnect
Aux 2A Quick Disconnect
Aux 3A Quick Disconnect
Case Drain Quick Disconnect
Electrical Plug
Aux 3B Quick Disconnect
Figure 44
Rear Hydraulic Connections (Optional)The rear of the MSV may have two pair of optional hydraulic connections (Figure 45). Each pair has a line out and a line in. Attachments are connected and Plus+1® controls are set to control the proper auxiliary ports (See Plus+1®).NOTEG� Some attachments will require these
connections to make them operational.
Aux 4A
Aux 4B Aux 5A
Aux 5B
Figure 45
M-B Multi-Service Vehicle • 48 • Maintenance©2014 M-B Companies Inc. All Rights Reserved
Maintenance
Preventative maintenance is a daily responsibility. The following charts provide a checklist of areas that should be inspected on a regular schedule.
PREVENTATIVE MAINTENANCEFrequency
As R
equired
Before Each U
se
Daily
Monthly
Annually
Inspect all hydraulic lines for evidence of leaking, loose fittings,
and frayed or damaged hoses.
X
Check hydraulic cylinders for broken or loose parts, especially
cotter pins on the hydraulic cylinders.
X
Check the hydraulic oil level. The Plus+1® will display an alarm if the level becomes low. A sight
gauge is located on the side of the reservoir for this purpose. Add fluid
as necessary.
X
Visually inspect that all access doors and panels are secured in
place.
X
Visually inspect for leaks under the vehicle.
X
Check Plus+1® for any active alarms before operating vehicle.
Service or repair as needed.
X
Frequency
EngineA
s Required
Before Each U
se
Daily
Monthly
Annually
Clean cooler intake. X
Inspect fuel filters; replace as necessary.
X
Drain moisture from fuel/water separator.
X
Check engine oil. X
Inspect air filter X
Frequency
Hydraulic System
As R
equired
Before Each U
se
Daily
Monthly
Annually
Check hydraulic fluid level; add fluid as required.
X
Frequency
Ground Drive
As R
equired
Before Each U
se
Daily
Monthly
Annually
Check tire pressure. X
Check connections for fluid leaks X
Frequency
Electrical
As R
equired
Before Each U
se
Daily
Monthly
Annually
Check battery terminals for corrosion.
X
Electrical guards in place. X
Inspect vehicle for loose or damaged wires
X
M-B Multi-Service Vehicle • 49 • Warranty©2014 M-B Companies Inc. All Rights Reserved
Replacement Parts / Warranty
For a complete listing of replacement parts, refer to the Parts Manual 904-183260.
Manufacturer’s Limited WarrantyThe M-B Companies, Inc. warrants all its M-B MSV products to be free from defects in materials and workmanship for 12 months, to begin with the delivery of said product to its original owner. This warranty is not transferable without the written consent of M-B.M-B will, at its own expense and without expense to the owner, replace all failed parts for and make all repairs that may be required by reason of workmanship or material in any part of the assembly of the product and associated components.Upon notice in writing, M-B will promptly repair or replace all defective or damaged items delivered under the contract. The batteries, tires, rubber materials, brushes and material normally consumed in operation, and major components such as engines, air compressors, and hydraulic pumps and motors are excluded from this warranty but shall, in any event, be guaranteed by M-B to the extent of any warranty received from its supplier.Any components replaced under warranty will be warrantied for the remainder of the original warranty. Replaced components do not restart the warranty period.If requested by M-B, products or parts for which a warranty claim is made are to be returned, transportation prepaid, to M-B’s factory. Any improper use, operation beyond capacity, or substitution of parts not approved by M-B, or alteration or repair by others in such a manner as in M-B’s judgement materially and/or adversely affects the product shall void this warranty.This warranty does not apply to defects caused by damage or unreasonable use while in the possession of the owner, including but not limited to: failure to provide reasonable and necessary maintenance, normal wear, routine tune-ups or adjustments, improper handling or accidents, operation at speed or load conditions contrary to published specifications, improper or insufficient lubrication, or improper storage.The M-B Companies, Inc. shall not be liable for consequential damages of any kind, including, but not limited to, consequential labor costs or transportation charges in connection with the replacement or repair of defective parts, or lost time or expense which may have accrued because of said defect. THE M-B COMPANIES DO NOT MAKE ANY WARRANTY OF MERCHANTABILITY OR OF FITNESS FOR A PARTICULAR PURPOSE. THE ONLY WARRANTY MADE BY M-B COMPANIES IS AS SET FORTH HEREIN. THIS WARRANTY CANNOT BE EXTENDED, BROADENED OR CHANGED EXCEPT IN WRITING BY AN AUTHORIZED OFFICER OF M-B COMPANIES, INC. (M-B’s total liability hereunder in no event shall exceed the purchase price of the product.)
CALIBRATION SCREEN 2
SEPARATE GROUND
DRIVE RAMP UP RANGE
SEPARATE GROUND
DRIVE RAMP DOWN RANGE
ADJUST THE PERCENTAGE OF SPEED IN WORK
MODE.
WE ADDED TWO LEVELS OF PROTECTION TO THE SCREENSTo get into the normal screens password is “501”This will allow you to move through the screens to verify different settings and calibrations. To make changes to the hydraulic flows the password “500” will have to be typed in after “501 “ was entered.We also added a scrape function and ride control. Currently are working on these option and will be available in the fall as an option. The software has been installed for these upgrades.