Students Dictionary

- 1 -

KELİME ÖRNEK CÜMLE

ABOUT The glue requires about 3 hours at room temperature to set sufficiently for the joint to be handled.

Hakkında, etrafında, civarında

ABSORB

The landing gear absorbs energy during taxiing, takeoff and landing.

Emmek, Soğurmak, Söndürmek, Susturmak. Telafi etmek,

ACCELERATION The accelerometer provides the Flight Data Recorder (FDR) with acceleration data from a three axis sensor.

Hız Artırma, Süratlenme, Hızlandırma, İvme

ACCEPT Check Moisture Vapor Prevention (MVP) cover to ensure it is in proper position to accept engine.

Kabul Etmek,Almak, Onaylamak

ACCESS These bolts are particularly useful for applications where access is limited or difficult.

Erişme, giriş, ulaşma

ACCIDENTAL The fire pull handles are normally locked to prevent accidental activation of the system.

Kazara, Yanlışlıkla

ACCOMPLISH Accomplish A-Check every 500 flight hours.

Yapmak, Başarmak, Başarıya Ulaşmak, Başarıyla Sonuçlandırma

ACCUMULATION Ice accumulation on the probe will result in a decrease of the resonant frequency.

Birikme, Yığılma, Yığma, Toplanma, Oluşma,

ACCURATE ACCURACY

To obtain accurate hydraulic quantities, the system being checked must be pressurized with either the engines or a hydraulic mule.

Hassas, Doğru Tam, İnce. Doğruluk, tamlık

- 2 -

ACHIEVE Adjust aileron trim cable tension as required to achieve cable tension.

Sağlamak, Ulaşmak, Elde Etmek. Başarmak,

ACOUSTIC The underwater locator beacon transmits an acoustic signal to aid in locating aircraft underwater following a crash.

Akustik, Ses.

ACROSS The molten metal is transferred across the arc gap to fuse with the workpiece.

Karşıda, karşıya, boyunca

ACTION Further cutting must not be executed in one continuous action

Hareket

ACTIVATE Solenoid Valve is activated by either of the two overspeed circuits.

Harekete Geçirmek, Devreye Sokmak, Etkili hale getirmek.

ACTUAL In Table 501, calculate error between actual fuel load and aircraft fuel system indications.

Mevcut, Güncel, Olan.

ACTUATE ACTUATOR

The valve contains a jet ejector pump and an air shut-off solenoid to actuate the valve open.

Hareket sağlamak Getirmek, İşletmek, Hareket Ettirmek

ADD / ADDITION ADDITIONAL

Conductive flooring is used when additional control of Electrostatic Sensitive Discharge is required.

İlave etmek, ilave, Eklenmiş.

ADDITIVE The following fuel additives are approved and subject to limitations stated.

Katkı maddesi.

ADEQUATE

Only an adequate procedure similar to the described procedure used for the preferred weights.

Yeteri Kadar,Yeterli, Uygun, Elverişli.

- 3 -

ADHESIVE This section includes general information for bonding and applying sealer and adhesives.

Yapıştırıcı.

ADJACENT However, it is possible for seepage or an allowable leakage to collect in a cavity of a unit or depression in adjacent structure over a period of time and falsely indicate excessive leakage.

Çok Yakın, Bitişik, Komşu.

ADJUST NOTE: If rig pins are tight or show signs of binding, it may be necessary to adjust force sensors.

Ayarlamak, Düzeltmek, Uydurmak, Alıştırmak ,

AFFECT The closeness of the terrain to the aircraft position affects the density and color of the dots.

Tesir Etmek,Etkilemek, Etki.

AGAIN Refer to Figure 28 again.

Tekrar

AGAINST Wearing the protective googles when removing safety wire can protect aginst eye injury.

E Karşı, E Doğru, E Zıt Yönde, E Değecek Şekilde

AGENT Rotating fire handle discharges a fire extinguishing agent into its associated engine.

Madde, Malzeme (Söndürme Tüpü İçindeki Söndürücü Madde).

AID This chapter describes standard maintenance practices to aid in maintaining the aircraft.

Yardım, Yardımcı ,Destek

AIRBORNE Compressed air can create airborne particles that may enter eyes or penetrate skin.

Havada Uçmak, havada Taşınmak.

- 4 -

AIRFOIL

The elevator trim tab is a movable airfoil located on the inboard trailing edge of the right elevator.

Hava kanatçığı, Kanatçık, İnce hava kanatçığı.

AIRFRAME Left / right air conditioning packs are attached to the airframe by six mounting points which allow the packs to be interchangeable.

Uçak Gövdesi

ALIGNMENT Do not use excessive force to obtain proper alignment of the tube and fitting.

Hizaya Getirmek, Ayarlamak, İstenen Konuma, Getirmek-Kurmak

ALLOW

WARNING: Allow APU cool. Before working on or near it. Hot components of APU can cause injury to persons.

Beklemek, Müsaade Etmek Olmasını Beklemek,

ALLOY The hinge forks are constructed of titanium alloy.

Alaşım: Halita, Maden Karışımı, Maden Halitası.

ALMOST The extent of corrosion attack is almost always inversely proportional to frequency of cleaning.

Hemen Hemen, Nerdeyse

ALONG Small cracks normally occur along the length of a rib or ribs.

Boyunca

ALSO A rotary disc cutter can also be used to cut a hole in sheet metal.

Keza , de, dahi

ALTERNATING For this reason, protection of all parts subject to alternating stress is particularly important, even in environments that are only mildly corrosive.

Değişken, Ardı Ardına, Değişimli, Değişik, Değişen

- 5 -

ALTHOUGH THOUGH EVENTHOUGH

-e rağmen

AMBER When the readout is outside of defined range, the numerals are depicted in amber.

Kehribar Rengi,

AMBIENT The remover shall be at ambient temperature.

Dış, Harici, Çevredeki, Çevreyi Saran

AMOUNT Use torque wrench to measure amount of torque required to overcome self-locking feature of each nut.

Değer, Miktar, Tutar

AMPLIFY The function of the amplifier is to amplify signal to a power output sufficient to operate the servo air pressure regulator.

Yükseltmek, Artırmak.

ANALOG The analog inputs on the fuel tank temperature are transmitted at a 200 msec update rate and a range of -70°C - 300°C.

Voltaj Değerli Sinyal, İbreli Gösterge,

ANGLE Ensure Angle Of Attack probe covers are removed and personnel stay clear of the probes or serious burns and demage to the aircraft may occur.

Açı, Bakış Açısı, Açı Yapmak

ANNULUS The locking keys are engaged in an annulus integrally machined into the outer cylinder.

Halka.

ANNUNCIATION

If emergency battery pack fails, a BAT FAIL annunciation will be displayed.

Yazı, İkaz, Bildirim,

ANOTHER Transfer may have failed due to system file could not be opened due to lack of disk space or file being locked by another user.

Bir başkasi, Baskasi, Başka biri

- 6 -

ANTISEIZE Apply a thin coat of antiseize compound to the threads of new bolts

Yapışmayı Sıkışmayı Önleyen, Kir, Pas Tutmasını Engelleyen

ANTISKID Check antiskid control unit, located in Right Electronic Equipment Rack (REER), for faults

Kaydırmaz: Kaymaya Engel

ANY Such bearings will not require any further lubrication during service.

Herhangi, her, hiç, hiç bir

APPEAR Pitting corrosion also appears in other types of metal alloys.

Gözükmek, görünmek, Varmak, Gelmek, Gibi Görünmek

APPLICABLE If leaks are found, disassemble leaking component or tire as applicable. This procedure is not applicable to aircraft having 1159SCC500-3 horizontal stabilizer actuator.

Uygun, Müsait, ygulanabilir, Tatbik edilebilir, kullanılabilir, Yapılabilir,

APPLICATION A filleting gun is used for the application of fillet seals.

Sürmek, Uygulama, Tatbik, Kullanıma Sokma.

APPLY 1. Apply electrical power to aircraft. 2. Wear personal protective equipment when applying and rinsing cleaning compound.

Vermek, Uygulamak, Kullanmak

APPROACH Flaps are used on take off to decrease ground run and on approach and landing to decrease stall speed, slow approach speed and shorten ground run.

Yaklaşmak, Yakına Gelmek

APPROPRIATE When left or right engine fuel pressure reaches 55 psi, the appropriate relay 291K1 or 291K2 closes and provides 28 VDC to the FDR power relay 107K3.

Uygun, Ayırmak, Tahsis Etmek, Kendine Mal Etmek

- 7 -

APPROVE(D) Mixing of engine oils is not recommended, but approved brands may be mixed if operational essential.

Onaylamak, Onaylı, Onaylanmış, Kabul Görmüş

APPROXIMATELY Keep treated area wet with alodine for approximately 3 to 5 minutes until a yellow color develops.

Yaklaşık Olarak,

AREA Leave the work area in a tidy and orderly manner and ensure that the equipmentis properly stowed.

Alan, saha

ARM Attach front adapter arm to forward end of engine lifting sling with pin and safety clip.

Kol, Kurmak, Kurulu Hale Getirmek,

AROUND Tools with plastic or insulated handles should not be used around Electrostatic Discharge (ESD) sensitive devices.

Civarinda, Etrafında,

ARRANGE ARRANGEMENT

Laminate composites can be designed to have fibres arranged along different directions.

Düzenlemek, düzenleme

ARROW Make sure the arrow on the valve body is pointed in the direction of flow.

Ok İşareti, Ok, Yön Belirtmekte Kullanılan Ok İşareti

ASH Wash entire aircraft to remove ash from fuselage skin, control surfaces, windshields and cabin windows.

Kül

ASSEMBLE ASSEMBLY

Assemble battery. Place cells back in case using care to place polarity marks in correct position.

Toplamak, Bir Araya Getirmek, Monte Etmek,Yerine Takmak. Montaj

ASSIST Under normal conditions, APU bleed air pressure is greater than the operating engine bleed air pressure, thus APU bleed air would be used to assist in the second engine start.

Desteklemek, Yardım Etmek.

- 8 -

ASSISTANCE The person performing a software load must determine software is correct and latest version. If unsure, contact Gulfstream Technical Operations for assistance.

Yardım, Destek

ASSOCIATE Pressurize air conditioning packs and inspect for leakage and security of air conditioning packs, associated equipment,.

İlgili, Bağlantılı,

ASSUME This procedure assumes engine is already being supported by engine lifting sling.

Varsaymak, zannetmek, Hesaba Katmak, Üstüne Almak, Farzetmek,

ATTACH Attach engine lifting sling to engine as follows.

Takma, Birleştirme, Ekleme

ATTACHMENT These connections permit the attachment of an external hydraulic test stand to operate the hydraulic subsystems of the aircraft.

Bağlama, Bitiştirme, Katma,Alma, Ek

ATTACK Ensure engine controls and Angle of Attack (AOA) probes operate freely.

Hücum, Saldırı,

ATTEMPT Verify portable water fire extinguisher is not pressurized before attempting disassambly.

Kalkışmak, teşebbüs etmek, denemek.

ATTITUDE Three Inertial Reference Systems (IRS) uses sensor data to calculate aircraft attitude, true and magnetic heading, angular and velocity.

Davranış, uçuş vaziyeti, uçuş durumu, duruş, uçağın uçuşta yaptığı hareketler,

AUDIO Comply with check of Audio Control Panels (ACP) as follows.

Ses. işitsel, duyma, radyo sinyalleriyle iletilen, yayılan, akustik,

- 9 -

AURAL This system supplies an aural warning and a crew alerting system message when a preset four letter code is received by one of the aircraft HF and VHF radios.

Kulakla ilgili, işitme yeteneğine ait , işitsel , duyulabilir

AUTHORITY Record all maintenance actions in accordance with current governing authority.

Talimat, Emir, yetki, yetkili, makam, nüfuz; hükümet.

AUTHORIZED Formula 409 cleaner has corrosive properties and is not authorized for use on aircraft.

Müsaadeli, Yetkili, Onaylı.

AUXILIARY The hydraulic actuator has pressure supplied from the left, right and auxiliary hydraulic systems.

Yardımcı, Yedek

AVAILABLE Above 35,000 feet, air is also available for electronic equipment rack cooling.

Mevcut, Hazır, Elde Edilebilir, Kullanışlı, Elde Mevcut

AVOID Use solvents in well ventilated areas only. Always wear adequate personal protective equipment and avoid breathing fumes. Keep away from spark producing devices and open flame.

Kaçınmak, Uzak Durmak, Yanaşmamak, Kaçmak, Kurtulmak, Önlemek, Engel Olmak

AVOIDANCE

The Traffic Alert and Collision Avoidance System (TCAS) is an auxiliary Air Traffic Control (ATC) system.

Sakınma, Kaçınma, Korunma

AWAY In some instances it will be necessary to cut away the damaged material and dress back the surrounding structure.

Uzakta, uzağa

AXIS AXIAL

it is recommended that the lateral axis be level and nose positioned so that it is pitched down.

Eksen Eksenle ilgili

- 10 -

AXLE Install bolt, washer and nut in axle fitting.

Aks, Çark Mihveri, Dingil, Mil, Mihver

BALANCE The purpose of the aileron trim tab is to balance aircraft roll around the longitudinal axis while in flight by slight movements of the aileron trim tab.

Denge, Kuvvet Dengesi, Muvazene

BALL

The pressure differential in the pilot valve moves the ball to its seat and closes off the entry of cabin pressure.

Bilya, Top , Küre , Yumak

BASE Mix together equal volumes of base component and catalyst component. - This assembly is made up of three parts; the lid, the base and the front plate.

Ana, Öz, Temel, Doğru içerik, Baz Gövde, Ana gövde Üs, merkez,

BASED

Each channel of the FCU consists of an identical microprocessor based controller with identical software.

Tabanlı, Temelli

BASIC

Troubleshooting the windshield alcohol anti-ice system requires the basic knowledge of electrical circuits.

Temel, Ana, Esas;

BATTERY When the battery is used, the flaps will not move until the EMER STAB button is selected to ARM

Pil, Batarya, Akü

BEACON Verify aircraft bottom beacon light is flashing.

Radyofar , Nirengi feneri, Far

- 11 -

BEAD Apply a bead of sealant to thread joint between cylinder nut and cap.

Küçük damla,

BEAM Inspect left and right wing rear beams for corrosion, paying particular attention to all connectors and components.

Kiriş, Direk, Mertek, Terazi kolu Araba veya Saban oku, Işın

BEARING Avoid direct rinsing of all bearings, bushings, electrical connectors and electrical components.

Yatak, Bilyalı, rulman

BECOME The catalyst or hardener only becomes active when it is heated.

Olmak, bir halden, durumdan diğerine geçmek, dönüşmek

BEHIND The observer seat is stowed behind the pilot when not inuse.

Arkasında.

BELL (CRANK) Adjust bell crank mechanism adjustment tube until there is no load on bell crank mechanism.

Hareketli, Dirsekli kol Manivela, Çan, Zil, Boru ağzı, Sütun başı,

BELT Timing belts are positive transfer belts and can track relative movement.

Kemer, kayış

BEND Handle fiber optic cable with care. Excessive bending of optic cable will cause demage to optical fiber core.

Bükme, Kavis, Kıvrım, Köşe; Viraj, Dönemeç

BETWEEN Each press of the pushbutton alternates the display between the two options.

Arasında,

BEYOND NOTE: Do not tighten fiber optic connectors beyond finger tight.

Daha Fazla, Daha çok, Daha ileri, Ötesinde, İlerisinde,

- 12 -

BINDING Perform a visual inspection during operational or functional tests and correct any binding or other problems as required.

Sıkışma, Katlanma, Birbirine Dolanma, Sarılma, Bağlama, İliştirme, Katlama

BIT (Built In Test) (ECU) Electronic Control Unit safely shuts down APU when a voluntary shut-down signal or a protective shut-down signal caused by Built-In Test (BIT) is received.

Test , İç Denetim Testi, Sistem Başlangıç Testi

BLADE After combustion gasses flow through blades of second stage rotor, they then flow out the exhaust.

Kanat, Pervane kanadı, Pal, pale, Keskin taraf ağız

BLANK This page is intentionally left blank.

Boşluk, Boş,

BLANKET A leaded plastic blanket is installed between and over the insulation to provide additional sound dampening.

Örtü, Battaniye,

BLEED The delivered conditioned bleed air used for cabin air conditioning is also used for cabin pressurization.

Motordan Alınan Hava, Kanatma Havası

BLOCK A spruce reinforcing block is usually glued to the inside of the splice if there are no uprights in the rib.

Blok, engel, kütük,

BLOWER Wear cotton clothing instead of wool or synthetics and use an ionized air blower to dissipate charges from nonconducting items.

Üfleyici, Fan

BOARD Over cleaning with abrasive materials may damage the resin surface of the laminate board.

Tahta, borda

BOND Allow bonded assembly to dry for a minimum of 30 minutes before inflating.

Yapıştırma, Bağlama, Ekleme, Demet Haline Getirme, İrtibatlama

- 13 -

BONDING

Whether direct or indirect, all electrical bonding must reflect high maintenance standards to maintain electrical integrity.

Bağlantı,Topraklama, Toprak, Bağlama, Bir Araya Getirme,

BOOM Cap strips may be known as booms

bumba

BOOT Cut safety wire and loosen both clamps on flexible boot.

Kauçuk, Lastik, Bot Şeklinde.

BOTTOM Do not tighten one screw at a time. Ensure to alternate between top and bottom screws

Dip, Alt, Esas, Kaynak, Temel kıç, popo. Dibine İnmek, Ulaşmak.

BOUNDARY A delamination area characterized by an irregular or jagged boundary indicates the separation of the vinyl and glass is not uniform.

Sınır, Hudut. Çevresini Oluşturan Çizgi, Hat, İz

BOWL Drain filter bowl into sampling bottle.

Çanak ,Yuvarlak Kâse, Tas, Küvet,

BRACE A brace link between the yoke and the pylon holds the yoke in a vertical position.

Dikme, Destek, Güçlendirmek,Desteklemek

BRACKET Remove mounting bolts with washers on each side of bracket assembly.

Mesnet, Köşebent, Dirsek

BRAKE When checking aircraft brakes for leakage, refer to Petlas Component Maintenance Manual.

Fren

BRAND It is desirable to keep to one brand of oil, but approved brands may be mixed if operationally essential.

Marka

- 14 -

BREAK Visually inspect pneumatic connections on top of Pressure Relief Valve for breaks or cracks.

Kesmek, Kırılmak, Parçalanmak, Ara, Mola ,

BREATHER Remove engine gearbox oil breather outlet plug.

Havalandırma Deliği

BRIGHTNESS

The DISPLAY BRIGHTNESS panel provides the flightcrew a means to control brightness for the four Display Units.

Parlaklık.

BRUSH Wash wheel wells and wing rear beams by manual washing methods such as scrubbing with a nylon brush.

Fırça.

BUBBLE

Secure a fluorescent light to sight glass to facilitate viewing of air bubbles.

Hava Kabarcığı,

BUILDUP The low limit valve is opened to prevent and remove ice buildup in the turbine ducting and condenser.

Oluşum, Gelişme, Çoğalma, Yığılma, İnşa etme, Birikme,

BULB Push in on bulb and rotate to remove or install bulb.

Lamba, Ampul, Çiçek Soğanı,

BUS Two Bus Power Control Units (BPCU) are provided for protection and control of the ac and dc buses.

Elektrik Takat Dağıtım Noktası.

BUSHING Exercise care around landing gear joints and bushings so the protective cover of old grease is not removed.

Yüksük, Kovan, Yatak, Ana Yatak, Burç, Bilezik, Ağızlık

- 15 -

CALCULATE The ECU also uses input from the speed sensor during flight to calculate the air inlet door position

Hesaplamak , Planlamak , Hesaplanan

CALL CALLOUT

Specific application areas and intervals are called out in the applicable maintenance manual sections.

Aramak, Demek, isimlendirmek, Bahsetmek, Belirtmek, Söylemek

CAP Remove protective caps and covers from the following connectors.

Kapak, Tapa,

CAPABLE (OF) For ground test and checkout procedures, an external hydraulic test stand capable of supplying 3000 psi may be used.

Yapabilme, Verebilme, Edebilme Yetenek ve Kaabiliyetinde Olmak, Yapılması Mümkün, Kabiliyetli.

CAPACITY The working capacity of the hydraulic systems is 4.8 gallons for LEFT system and 1.6 gallons for RIGHT system.

Hacim, İstihap Haddi. Kapasite , Yetenek , Durum

CAPTIVE Loosen captive screws securing panel to console.

Kapalı, Sabit, Hapsolmuş, Esir

CARE

Oil, grease and solvents may burn or explode spontaneously when in contact with pressurized oxygen. Extreme care must be taken to avoid any contamination of oxygen systems and components.

Hassiyet, Özen, Dikkat, Çaba, Bakım, İlgi, Aldırmak,

CARRY CARRIER CARRY OUT

SRM provides the information to carry out most of the repairs encountered in normal service.

Taşımak, nakletmek, taşıyıcı, İcra,ifa etmek

CART Disconnect pressure fill cart from pressure fill fitting and install dust cap

Cihaz, Taşımak , Götürmek

- 16 -

CARTRIDGE The engine fire bottle cartridges are installed on the left and right engine fire bottles.

Katriç,

CASE Remove safety clip and pin that attach front adapter to intermediate case.

Kasa, Çerçeve, İskelet, Gövde, Göbek, Durum, hal

CAUSE

Forcing aileron trim knob beyond its mechanical stops may cause demage to trim system.

Sebep, Sebep Olmak, Yol Açmak

CAVITY Carefully work the two electrical connectors onto the control wheel cavity.

Bosluk, Oyuk, Çukur

CELL The left and right wings are divided into eight cells with each cell having 1 - 4 fuel probes.

Hücre, Gözenek, Pil

CENTRAL The radio management and control subsystem supplies a central control for all radio systems.

Merkezi, Ana, Temel, Uygun, Kolayca Ulaşılan,

CERTAIN Certain areas of all aircraft are sealed or to prevent corrosion by sealing against the weather.

Belirli, bazı

CHAIN The biggest threats to chain drive systems are dust and rüşt.

Zincir, zincir halkası

CHAMBER When the differential pressure exceeds a calibrated set point, the metering sections open to modulate the control chamber pressure.

Hazne, Oda , Kabin , Kamara

CHANGE The output voltage of the speed sensor changes as the gear teeth move through the speed sensor magnetic field.

Değişmek, Değiştirmek, Değişiklik

- 17 -

CHANNEL The dual channel controller controls the rate of change of cabin pressure as well as the level of cabin pressure.

Hat, Kanal, Mecra, Yatak (nehir vs.)

CHAPTER This chapter describes standard maintenance practices to aid in maintaining the aircraft.

Bölüm , Kısım ,

CHARGE If battery voltage falls below level, perform top charge in accordance with Component Maintenance Manual.

Yükleme, Doldurmak, Şarj etmek, Talimat

CHEMICAL Corrosion is the deterioration of a metal by a chemical or electrochemical reaction within its environment.

Kimyasal.

CHIP

Inspect for dents, chips, nicks, pitting and gouges.

Çapak, Talaş, Yonga, Çentik.

CIRCUIT BREAKER CIRCUT

Ensure the following Circuit Breakers (CB) are depressed:

Devre Kesici, Sigorta Devre

CLAMP Remove screws nuts and washers from both bonding clamps on forward end of silencer.

Kelepçe, Kelepçelemek,

CLEARANCE If there are indications of rubbing, the clearance should be increased still further.

Aradaki Boşluk, Aralık, Boşluk, İki Şey Arasındaki Mesafe

CLIMB Cabin rate of climb indicator displays a value more negative than that recorded in Step 1.B.(7).

Tırmanış, Tırmanma

CLOCKWISE Rotate left fire pull handle clockwise and hold.

Saat istikameti, soldan sağa doğru,

- 18 -

CLOSE Close tolerance holes and fasteners ensure more equal load distribution

Kapatmak, kapalı, yakın

CLOSEOUT Upper and lower closeout ribs are rivet bonded in place between the left and right leading edge.

Zemin, Tavan. Kapak

COAT

Apply a thin coat of Loctite to threads of screws.

Tabaka, Kat, Kaplama

COATING If there is dry film lubricant coating, remove the coating locally from the front face of fan disc.

Tabaka, Katman, Kaplama, Kaplamak, İnce Yağlamak, Örtü

COEFFICIENT The coefficient of friction is ind ependent of the shape of the belt

Katsayı

COIL

Bobin, halka, kangal

COLLECT The cleaning solution that drains out of fuel tanks should be collected.

Toplamak

COLLISION When the alerts are on, areas of terrain that satisfy the terrain collision alert conditions are displayed in solid red on the terrain display.

Çarpışma

COLUMN For parts prices, see the unit price column of the tables.

Sütun

COMBINATION

Corrosion may proceed at a rapid or slow rate. The rate depends on the metal or combination of metals, undergoing attack, the environment, the concentration of reactants and the prevailing temperature.

Karışım, Bileşim,

COMBINE Placing aircraft in air mode or pulling combined WOW circuit breaker with APU running will cause an overtemperature condition.

Birleşmek, Birleştirmek

- 19 -

COMBUSTIBLE Skydrol type IV Phosphate ester hydraulic fluid is combustible and can be a health hazard. Inhalation of vapor and contact with skin and eyes should be avoided.

Yanabilir, Alev Alabilir.

COMBUSTION The purpose of the engine system is to convert heat energy from combustion of a fuel / air mixture into shaft power.

Yanma,Tutuşma

COMMAND When the air shut-off solenoid is commanded open, the secondary vacuum flow draws air from the control chamber.

Kumanda Vermek, Etmek, İdare Etmek, Kumanda, Komut,

COMMERCIAL A number of commercially available cleaners and other products used as cleaners.

Ticari Olarak

COMMON

After having been cooled, conditioned and dehumidified, the air is discharged to a common cold air manifold.

Ortak, Genel, Bilinen.

COMMONLY Electrostatic Discharge (ESD), commonly known as static electricity, seems harmless, but it can damage electronic components and assemblies.

Genel, Genellikle. Ortaklaşa

COMMUNICATION (with) Communication with another TCAS equipped aircraft is supplied by the onboard transponders.

İletişim, Haberleşme, Haber, Mesaj

COMPARE Compare corrected capacitance value to acceptable capacitance value.

Kıyaslamak, Karsilaştirmak, Mukayese Etmek,

COMPENSATE The left system reservoir has a 0.8 gallon expansion capability to compensate for hydraulic fluid thermal expansion.

Telafi Etmek, Karşılığını Ödemek.

- 20 -

COMPLETE All maintenance should be completed before operation of air distribution ducts to protect system components.

Tamamlamak, Tam

COMPLETELY Slide heat shrink tubing over connector to completely cover connector junction.

Tamamen , Bütünüyle

COMPLIANCE (WITH)

It is the sole responsibility of the user to ensure protection from injury or exposure; safe application of materials; and compliance with any federal, state or local regulations regarding the use of any of the materials specified.

Uygun Davranmak, Uyma, İtaat

COMPLY Do not comply with any software load checks until all CDs are loaded.

Yapmak, Uygun Olarak Yapmak, Uygulamak, İsteneni Yapmak,

COMPONENT Ensure air conditioning system has been shut down and components have had sufficient time to cool.

Parça, Eleman, Cihaz

COMPOUND Apply Type III corrosion inhibiting compound to connector mating surfaces.

Pas önleyici, koruyucu Yağ, Bileşik,

COMPRESS COMPRESSION

Stretch tape 25% to 50% to ensure good compression around connector body and backshell.

Sıkıştırmak, kısaltmak, özetlemek, Sıkıştırma, Basınçlandırma,

CONCERNING Material Safety Data Sheets shall be consulted for all materials to determine the manufacturers reccomendations concerning occupational exposure precautions.

İle İlgili/hakkında, E dair

- 21 -

CONDENSER Check relief valve in aft end of separator condenser for freedom of movement.

Yoğunlaştırıcı.

CONDITION

Components in a static condition are allowed a maximum leakage of two drops per seal or packing a day.

Durum. şart, koşul,

CONDUCTIVE Before assembly, the joints are treated with a conductive film that prevents corrosion of the bonding surface.

İletken.

CONNECT Caution: Electrical power shall be off when connecting and disconnecting electrical connectors to prevent arching between pins.

Takmak, İrtibatlamak, Bağlamak,

CONNECTION If continuity is satisfactory, connect the cable connection at the opposite end of the loop.

Bağlantı, İlişki, Bağ, Müşteri Aktarma,

CONSIDER The use of corrosion inhibiting compounds on control cables is not considered a suitable substitute for cleaning and corrosion protective procedures

Dikkate Almak

CONSIST (OF) Silicone Sealing Compounds generally consist of one component, which cures by reaction with moisture in the air.

İçermek Sahip olmak, Oluşmak, (in ile) Bağlı Olmak,Dayanmak

CONSTANT CONSTANTLY

A supply regulator is attached to the cylinder to reduce high cylinder pressure to a lower constant line pressure.

Devamlı, Sabit Devamlı bir şekilde

CONSTRUCT CONSTRUCTION

Components constructed of composite materials are used throughout aircraft structure.

Yapmak, İmal Etmek Yapı

- 22 -

CONSULT

Before using solvents, consult Material Safety Data Sheet (MSDS) for special precautions or warnings.

Bakmak, Danışmak, Başvurmak.

CONSUMABLES Refer to the specific chapter for consumables: Safety wire, Lubricating oil, Cotter pin, etc.

Sarf Malzemeler

CONTACT Do not breathe vapor or allow liquid to contact skin. Wear protective clothing, rubber gloves and a face mask.

Temas Etmek, Bağlantılı Olmak, Temas Halinde Olmak,

CONTAIN Each error message displayed to user contains a general description of problem along with an associated error code.

İçermek, Sahip Olmak, Kapsamak, Bünyesinde Barındırmak

CONTAMINATE Disconnect the hose assembly from the bottle and the valve, taking care not to contaminate the sample.

Kirletmek.

CONTAMINATION Do a visual check of the engine oil in the oil-level sight glass for contamination.

Kirlilik, kirlenme, pislik, gaz/radyasyon bulaşması.

CONTINUE If one of hydraulic systems fails, the rudder actuator will continue to operate and send a single rudder message.

Devam etmek,

CONTINUITY The voltmeter shall indicate continuity from zero to 28 degrees,

Süreklilik ,Devamlılık.

CONTINUOUS Type IV compound is to be applied directly from container in a thin continuous film by brush, knife or spatula.

Sürekli Devamlı

CONTOUR

The wheel and tire are faired into the lower contour of the wing.

Dış yüzey, Diş Hat, Çevre,

- 23 -

CONTROL Slowly adjust the appropriate control valve to the required pressure.

Kontrol etmek, idare, kontrol,denetlemek,denetim

CONVENTION Carbon is necessary for the hardening of conventional high tensile steels.

Geleneksel, basmakalıp,

CONVERT

Each converter is capable of converting the ac alternators output into 23 kVA, 115 / 200 volt, 400 Hz, three-phase.

Çevirmek, Dönüştürmek.

CONVERTER The converters, in turn, supply 23 kVA, 115 / 200 volt, 400 Hz, three-phase ac power to the ac buses.

Dönüştürücü, Çevirici.

COOLER/COOLING Put a container in position below Fuel Cooled Oil Cooler.

Soğutucu, Soğutma Tertibatı, Soğutma Cihazı, Soğutucu Radyatör

CORD The wrist strap incorporates a 1 megohm current limiting resistor in series with the ground cord to protect the wearer from electrical shock.

Kordon, Kablo, Fiş Kordonu, Sicim İp, Halat,

CORE The corrosion effects continue like threads to all sides as 'filiform corrosion' but do not enter the core.

İç, öz, dahil

CORRECTION For temperature corrections, add 1% pressure for each 5°F above 70°F,

Düzeltme., Doğru Hale Getirme,

CORRECT CORRECTLY

Make sure that installed sealing rings are not twisted and are correctly installed in the groove.

Doğru Olarak, Doğru Uygun Biçimde

CORRESPONDING Verify cabin differential pressure indicator agrees with corresponding psig for test altitude.

Karşılık Gelen, Uygun Olan, Uygun.

- 24 -

CORROSION Apply Corrosion Inhibiting Compound to axle fitting as follows:

Pas,

CORROSIVE At normal atmospheric temperatures, metals do not corrode appreciably without moisture, but the moisture in the air is usually enough to start corrosive action.

Paslanma, Paslandırıcı, Çürütücü, Aşındırıcı, Kemirici

COUNTERCLOCKWISE Clockwise rotation of oil pressure regulator adjusting screw increases and counterclockwise rotation decreases the regulated pressure.

Saat yönünün tersine.

COUPLE COUPLING

Connector coupling rings should be lock-wired to aircraft structure. Do not lock-wire from coupling ring to backshell.

Birleştirmek, bağlamak, bağlantı, çiftleşme

COURSE In the present course the views are arranged by the first angle projection method.

Ders, kurs, seyir, rota, yön, gidişat

COVER Cover sensing port to prevent contaminants from entering tube.

Örtmek, Üstünü Kapatmak, Örtü, Koruma Kapağı, Kapak

CRACK Cracks can be located by visual inspection or the magnetic particle method.

Çatlamak, çatlatmak, kırmak, çatlak

CRANE Remove engine lifting sling from overhead lifting crane.

Vinç, Kaldıraç, Calaskal,

CRITERIA This criteria is applicable to all in service aircraft hydraulic system components.

Kural

CRITICAL it is critical the correct sealant be chosen for a specific area / situation and be applied correctly.

Önemli, Ciddi, Tehlikeli, Eleştirel

- 25 -

CROSS Vertical movement feature lets display remain in an easily readable and flyable position during high crosswinds.

Çapraz, Yan, Çarpı/Artı İşareti Geçmek, Kesişmek

CROSSOVER Using tensiometer, verify crossover speed brake cable tension in main wheel well is 45 pounds ± 5 pounds at 70°F.

Çapraz Olarak Üstten, Alttan vs. Geçmek, Geçit, Köprü

CURE Allow sealant to cure a minimum of 72 hours before pressurizing the airplane.

Kurumak (Conta, Macun vs.) İyileştirmek, Tedavi Etmek,

CURRENT GOVERNING AUTHORITY

Record all maintenance actions in accordance with current governing authority.

Mevcut Emir ve Talimatlar

CURSOR Using SCROLL knob, place cursor on WX and press trigger to select.

Yer göstergeci, Yer İmleci, Yer Belirleyici, Yer Seçici

CUSTOM Error Codes can be reviewed by Gulfstream Customer Support to aid in determining best course of action to complete download operation.

Müşteri, Gelenek, Alışkanlık, Âdet, Gümrük,

CUSTOMER At customers discretion and responsibility, the following procedure is to be performed by a certified repairman.

Müşteri.

CUT Inspect grounding cables and bonding straps periodically to ensure they are free of corrosion, fraying or cut.

Kesmek , esik

CUTOUT Ensure area around cutouts are clean and free of sealant.

Kesmek, Durdurmak, Kesip Çıkarmak, Kesit, Kesilerek Şekil Verilmiş ey,

- 26 -

CYCLE Dissipate hydraulic system pressure by cycling flight controls several times.

Harmanlamak, İçinde Dolaşmak Dönme, Dönüş, Devir Yapmak,

DAMAGE The damage must be classified into one of the following categories.

Hasar

DAMP This substance is noncorrosive, nontoxic and nonirritating and can be wiped away with a clean damp cloth.

Nemli, Rutubetli, Islaklik

DASH Right fuel flow indication momentarily displays amber dashes followed by amber slashes.

Tire İşareti, Kesik Çizgi.

DATABASE If the calculated values do not agree with the data in the database, the EGPWS causes an aural alert.

Veri Tabanı

DEACTIVATE Deactivate the thrust reverser before you do work on or around it.

Durdurmak, Çalışmasına Son Vermek, Susturmak,

DEACTIVATION Circuit breakers have to be reset after completion of deactivation procedure of the system.

Devre Dışı Bırakma, Kapatma, Etkisiz Hale Getirme.

DEATH WARNING: Failure to remove electrical power from APU may result in serious injury or death.

Ölüm,

DEBRIS Surfaces to be joined shall be wiped clear of dirt, dust or foreign debris.

Kalıntı, Döküntü, Kırıntı.

DECREASE When the engine is stable at maximum EPR value, decrease the engine speed to 85 percent.

Azaltmak, Azalmak.

- 27 -

DEDICATE A dedicated Generator Control Unit for each generator provides voltage regulation over /undervoltage protection over/underfrequency protection, speed control (IDG only)

Tahsis Etmek, Emrine/ Kullanımına Vermek, Adamak, Vakfetmek.

DEEP DEPTH

The characteristic of solder flowing and its penetration depth is influenced by the type of solder and the fluxing agent.

Derin, derinlik

DEFECT Discard check valve if corrosion remains after cleaning and / or if pitting, nicks, dents or other defects are present which would affect operation of the valve.

Hasar, Kusur, Noksan, Eksiklik.

DEFINE DEFINITION

The basic principle of effective troubleshooting is to clearly define and inte et threported symptom and then proceed to a logical and systematic method of diagnosis.

Belirtmek, tarif etmek

DEFUEL It is not necessary to defuel the aircraft prior to biocide treatment.

Yakıt Boşaltmak.

DEFUELING Disconnect fuel feed line just downstream of defueling valve and install protective caps and covers on open end.

Yakıt Boşaltma, Yakıt Boşaltmak,

DEGREASE MIL-PRF-680 or equivalent dry cleaning solvent is used to degrease and clean tubing and fittings.

Yağdan Arındırmak, Çözmek, Temizlemek

DEGREE When the angle-of-attack has decreased by one degree or more, the solenoid valve de-energizes.

Derece.

DEICING Chemical means is the use of spraying of deicing fluids which may be used hot or cold.

Buz Çözücü, Buza Mani

- 28 -

DELAMINATION Windshield delamination can occur between the glass core ply and glass inner ply.

Katmanlaşma, Kabarma, Kat kat olma, Yapraklanma, Katmerlenme

DELAY Batteries alone provide power only for a limited amount of time. Do not delay in performing following checks.

Gecikme Yapmak, Gecikmek,Geciktirmek, Ertelemek, Gecikme

DENT Dent is a depression with rounded edges having no sharp bends or edges.

Ezik, Vuruk, Oyuk, Çukur, Çökük, Göçük, Göçürmek, Yamulmak

DENSE DENSITY

The density is determined by weighing and measuring the volume of a sample cut from the plank.

Yoğun, yoğunluk

DEPEND To remove ducts in this area, it may be necessary to start at the forward end depending upon completion. Normally start at the rear if removal of all ducts are not required.

Bağlı Olmak,

DEPLOY Left flight spoilers may deploy slightly when control wheel is rotated clockwise.

İntikal Etmek, Haraket Etmek

DEPLOYMENT Each container has an extinguishing agent deployment tubes to supply the extinguishing agent to either the left engine or the right engine.

Sevk, İletim, Yollama, Gönderme, İntikal, Nakletme, Yayılma, Açılma

DEPRESS Remove safety clips, tags and depress circuit breakers pulled in Step 1

Basmak, Bastırmak, İttirmek,

DEPTH Engineering will advise on depth of pitting, whichmay be sanded out.

Derinlik

- 29 -

DESCEND WARNING: do not exceed 1000 feet per minute rate of descent.

Alçalma.

DESCRIBE DESCRIPTION

System Description

Açıklama, Tanıtım, Betimleme

DESIGN Materials must be selected primarily for structural efficiency. Corrosion resistance is necessarily a secondary consideration in design.

Dizayn, Plan, Fikir, Model,

DESIRE The desired temperature is selected by rotating the COLD / HOT rheostats on the TEMP CONTROL panel.

Arzu etmek, İstemek, Arzulamak, Arzu, İstek,

DETACH The ladder can be detached from the tail compartment and used to access other locations on the aircraft.

Alıp Götürmek, Ayırmak.

DETAIL DETAILED

Detailed Inspection

Ayrıntı, detay, Ayrıntılı, Detaylı

DETECT

If a malfunction is detected during the self-test, a Cockpit Voice Recorder Fail advisory message is displayed on the crew alerting system and the red fault indicator on the CVR control unit comes on.

Bulmak, Ortaya Çıkarmak, Tespit Etmek,

DETECTION Built-in test provides fault detection for internal failures within the ECU as well as external failures in any APU components

Tespit, Bulma, Ortaya Çıkarma

DETECTOR Inspect engine front chamber Magnetic Chip Detectors

Toplayıcı, Bulucu, Keşfedici, Hissedici,

- 30 -

DETENT Open printer front cover to first detent and observe the following indicator lights are lit:

Durak noktası, tahdit, sınır, tutma, durdurma tetiği, mandalı

DETERMINE Perform Step 3 on both systems to determine if excessive friction is forward of elevator actuator.

Belirlemek, Karar Vermek, Niyetlenmek, Kararlaştırmak,

DEVIATE DEVIATION

If error message displayed, file size may be invalid or content may be invalid due to deviation from expected format.

Dışına Çıkmak, Sapmak, Ayrılmak, Yoldan Çıkma Sapma

DEVICE Tools with plastic or insulated handles should not be used around ESD sensitive devices.

Cihaz, Parça, Eleman, Alet,

DIAGNOSE BITE check can assist in determining failed component when a loop is diagnosed as faulty.

Belirlemek, Teşhis Etmek, Fark Etmek, Kanaatine Varmak, Bulmak,

DIAGRAM Using schematic diagram, connect test wires to detection loop electrical connector pin A and pin D.

Çizim

DIAMETER Safety wire diameter shall be between 1/3 and 3/4 of hole diameter.

Çap

DIAPHRAGM Flow regulation is established by pressure differential across diaphragm of Differential Pressure servo.

Zar, Diyafram, Körük.

DIFFERENCE The corrosion attack, which is electrochemical in nature, ensues because of differences in the concentration of ions or of dissolved gases.

Farklılık, Değişiklilik, Fark, Değişiklik,

- 31 -

DIFFERENT The Auto Pilot pitch control system controls the aircraft when climbing or descending to a different altitude to ensure a smooth and safe altitude change.

Farklı, Ayrı, Başka, Değişik, Çeşitli

DIFFERENTIAL The Pressure Relief Valve (PRV) contains two fully independent positive pressure relief metering sections which sense differential pressure between the cabin and the atmosphere.

Fark,

DIGITAL The cabin and cockpit temperature control is provided by a digital electropneumatic control system.

Sayısal, Sıfırdan Dokuza Kadar Olan Sayılar,

DIMENSION If delamination is found, the exact dimensions of damaged area must be determined by use of ultrasonic or X-ray equipment.

Ebat, Çap, Boyut

DIRECTION Finish polish in a radial direction.

Yön,Kontrol, İdare, Yönetim Talimat, Yönerge

DIRT Cap all fittings opened by removal of oxygen cylinder to prevent dirt from entering and contaminating system.

Pislik, Kir, Toz

DISABLE

To prevent false alarms, the lightning sensor is disabled.

Devre Dışı Bırakmak, Hariç Tutmak , Mahrum Etmek

DISASSEMBLE Inspect battery for the following conditions: If any exists, completely disassemble battery.

Sökme, Parçalara Ayırma.

DISCARD Remove O-rings from unions and tee. Discard O-rings.

Atmak, Çöpe Atmak,

DISCHARGE If the compressor discharge pressure is less than the inlet pressure, the air will bypass the compressor section.

Çıkış, boşaltım hattı, boşaltmak

- 32 -

DISCOLORATION Clean the area until there is no discoloration on the drying cloth.

Renk bulaşması, Atması, Renk Bozulması, Değişmesi,Solması,

DISCONNECT NOTE: Do not disconnect launch cable from optical light source until test is complete.

Ayırmak, Bağlantısını Çıkartmak, Devreden Çıkartmak. Sökmek,

DISCOVER If damage is discovered, window must be repaired or replaced.

Tespit Etmek, Bulmak, KeşfetmekOrtaya çıkartmak

DISCREPANCY NOTE: If there is a discrepancy in cable lengths, contact Gulfstream Technical Operations.

Sorun, Uyuşmazlık, Arıza, Ayrılık, Zıtlık, Başkalık,

DISCRETE Both channels drive their discrete outputs, but only the active channel drives the valve via its own dedicated motor.

Ayrık, Ayrı, Farklı

DISENGAGE If removing aft section of duct, cut cable ties and disengage ducts from sleeves

Birbirinden Ayırmak, Ayırmak, Kurtarmak

DISPLACE This material has the ability to penetrate into extremely small cavities and to displace water.

Yer Değiştirmek , Yerinden Çıkarmak , -in Yerine Geçmek

DISPLAY Cockpit duct temperature displays approximately same temperature as recorded in Step 1.

Göstermek, Görünmek, Ekrana Yansıtmak, Ekran

DISPOSAL Discard old battery in accordance with federal and local hazardous material disposal regulations.

Elden Çıkarmak, Atmak, Çöpe Atmak, Atık

DISSIPATE Each person handling ESD sensitive components must wear a grounding strap to dissipate bodily electrostatic charges.

Üzerinden Atmak, Dağıtmak, Dağılmak, Harcamak

- 33 -

DISTANCE Measure distance between upper cowl door and inlet cowl .

Mesafe, Uzaklık

DISTORTION Shorten linkage until door closes completely without distortion of door or structure and without causing failure of the gear uplock.

Zarar vermek, Çarpıtmak, Çarpıklık, Çarpılma, Bükülme, Bozulma, Biçim Yitimi

DISTRIBUTION The cockpit conditioned air distribution system controls conditioned air throughout the cockpit area for maximum comfort.

Dağıtım, Dağıtma, Yayılma, Yaygın Olma

DIVIDE The manifold is divided into four sections for removal of contaminants from the left hydraulic system.

Ayırmak, Bölmek, Bölünmek

DOT The RUN mode is indicated by two fixed dots located between hours digits and minutes digits.

Nokta

DOUBLE In Control Panel window, double click Network and Dial-up Connections icon to select.

Çift, İki.

DOWNLOCK The side brace actuator incorporates an internal downlock mechanism located in the lower end of the cylinder.

Altta Kilitlenen, Alt kilit

DOWNSTREAM

Check valves and other hydraulic components may have static pressure dowstream or upstream of lines being opened or removed. Use approved splash googles or face mask and gloves when opening hydraulic lines that may have pressure in their respective system

Çıkış, çıkış hattı,

- 34 -

DRAG The flaps increase wing area and camber as they extend aft and down, resulting in increased lift and drag.

Çekme, direnç, geri çekme(hızla) sürükleme, sürüklenen şey, engel, sürüklemek,

DRAIN (Plug) TO DRAIN

Remove safety wire and drain plug from the fuel line and allow all fuel to drain

Boşaltma (Tıpası), Boşaltmak, Dışarı Akıtmak

DRAW DRAWING

Marking-out is e transfer of drawing dimensions onto the workpiece.

Çizmek, çekmek, Çizim

DRILL Some are coded to indicate a drilled or undrilled head

Alıştırma, talim, Matkap,delmek

DRIVE DRIVEN

The ECU is an electrically driven, digital computer based controller which is programmed to control all APU electrical functions.

Sürücü, Sürmek, Hareket Vermek, Hareket Aktarmak, çalıştırmak,Çakmak

DROP

Wipe surface clean and place a drop of hydraulic fluid on area.

Damla, Düşüş, Düşmek, Koymak,

DRUM Lower control head and control rods assembly and insert control rods into cable drums.

Tambura, Sarma Makarası

DRY If there is dry film lubricant coating, remove the coating locally from the front face of fan disc.

Kuru, kurutmak, kurumak

DUAL The engine ignition system is a dual igniter system requiring a DC power input of 10 to 30 volts for operation.

İkili, İki Eş Parçalı, Çift, İki Yanlı

DUCT If tube or duct is aluminum, apply alodine solution to bonding surface with a clean sponge, brush or cloth.

Kalın, Geniş Boru

- 35 -

DUE This filter is a time change item and should be changedwhen the system functional test is due.

Zamanı Gelmek, Yapılması Gerektiği, Olacağı Zaman/Tarih

DUE (TO) Pressure washing of aircraft is not recommended due to the adverse effects on aircraft components.

-den dolayı, Sebebiyle, Vasıtasıyla, Vakti Gelmek,

DUMP The lavatory servicing access door provides access to the lavatory dump and servicing receptical.

Boşaltmak, Atmak.

DURING The trim tab adjusts the position of the ailerons during flight.

Boyunca, Esnasında

DUST Disconnect dust cap from coupling and examine both for contaminants and damage.

Toz , Toprak , Çöp

EACH Swaged end fittings are used at each end oft he cable to transmit and actuate the required movement.

Her, herbiri

EARTH The neutral cable is connected to earth potential by the electricity supply authority

EASILY Type I and II Corrosion Inhibiting materials are durable materials not easily removed by normal use.

Kolayca, Rahatlıkla. Kolay Kolay, Kolaylıkla

EDGE Inspect pulleys for roughness, sharp edges, material embedded in grooves and wear.

Kenar,

- 36 -

EFFECT

Actuation of cockpit switch has no effect at idle RPM and above.

Etki, Sonuç, Anlam

EFFECTIVE An understanding of the function of the components and circuit is necessary to perform effective troubleshooting.

Etkin, Etkili, Tesirli, Yürürlükte Olan,

EFFICIENT EFFICIENCY

Belts provide an efficient load transfer between shafts on a wide variety of applications.

Etkili, etkinlik

EITHER The power supply for shielded metal arc welding may be either AC or DC.

Ya,yada, her iki

EJECTOR The valve contains a jet ejector pump and an air shut-off solenoid to actuate the valve open.

Püskürtme, Püskürtme Memesi, Ucu, Püskürtücü Meme, Uç,

ELABORATE Surface cleaning and elaborate access procedures may be required.

Ayrıntılı, Özenli, Detaylı

ELBOW

At flow regulator, loosen lock nut then remove elbow and O-ring.

Dirsek, Boru Dirseği, Zaviye Parçası.

ELECTRICALLY The static dischargers should be connected electrically to the main aircraft structure.

Elektriki çalışan , Elektriki

ELEMENT Check filter housing for damage and inspect filter element for presence of dust, dirt and other contamination.

Gövde, Eleman, Unsur, Öğe

ELEVATION ELEVATOR

If the landing altitude data is not inputted via the selector knobs, the landing field elevation retained in memory shall be used for computation

Deniz Seviyesine Göre Yükseklik, İrtifa Asansör

EMPENNAGE Flight controls are moveable surfaces attached to wings and empennage structures that modify aerodynamic forces.

Kuyruk takımı , Dümen

- 37 -

ENABLE The purpose of the portable fire extinguishers is to enable the crew to extinguish cabin fires.

İmkan Tanımak, Olanaklı Kılmak , Elverişli Olma

ENCLOSURE The APU is installed within a fireproof titanium enclosure, located in the tail section.

Kapalı Alan, Hazne, Zarf İçine Konulan Şey, İlişikte Olan Şey

ENCOUNTER During course of data loading, user may encounter problems at various stages of software loading process.

Karşılaşmak, Rast Gelmek, Denk Gelmek,

ENERGIZE

If both power levers are in the idle position, the power lever relays are energized, connecting power to the GND SPLR.

Enerjilemek

ENGAGE Lower engine until transit stand trunnions engage and are horizontal in the front support clamp blocks.

Birbirine Geçirmek, Tutturmak Saldırmak, Hücum Etmek

ENHANCE Fuel Quantity Signal Conditioner receives inputs from two densitometers to enhance the accuracy of the fuel quantity processing.

Artırmak, Çoğaltmak

ENOUGH Apply enough locking compound to fill all space between parts.

Yeteri kadar, Yeterince , Yeterli,

ENSURE Each operator should evaluate the environment of the aircraft, inhibitor used and application interval to ensure adequate corrosion protection.

Emin Olmak , Kesinleştirmek, Sağlamak

ENTER The cooler compressed air enters reheater portion of the reheater and condenser.

Girmek, İçeri Girmek,

ENTIRE A malfunction of any one of the three parts requires removal and replacement of entire unit.

Tüm, Bütün.

ENTRANCE Prevent entrance of moisture into the nacelle internal areas.

Giriş Yeri, Kapı, Girme, Giriş, Giriş Hakkı

- 38 -

ENTRY Ensure main entry door is open

Giriş

ENVIRONMENT The immediate environment surrounding ESD sensitive components and equipment must be free of electrostatic fields or must have a suitable static shielding

Çevre, Çevre Şart ve Etkileri, Ortam.

ENVIRONMENTAL The flight environment data system senses environmental conditions to determine and display aircraft attitude and direction.

Çevresel, Ortamsal,

EQUAL Upper and lower aileron trim cables should have an equal number of wraps on aileron trim actuator drum.

Eşit

EQUIP, EQUIPPED, EQUIPMENT

The aircraft is equipped with a Standby Electrical Power (SEP) system consisting of a Hydraulic Motor Generator.

Teçhiz etmek, donatmak. Donatılmış Teçhizat, donanım

EQUIVALENT Antiseize compound, C5-A or equivalent, can be used to coat small diameter threads of igniter adapters.

Muadili, Eşiti, Eşit Muadil Eşit Miktarda,

ERASE The pushbutton allows the pilot to erase flight plan, reference or waypoint information or insert waypoints into flight plans.

Silmek, Gidermek, Yok Etmek.

EROSION Verify no evidence of erosion on painted surfaces of radome, forward fuselage and/or nose landing gear doors.

Aşınma, Erozyon.

ERROR An error code will be set when a signal from the N1 probe of channel A is out of limits.

Hata, Yanlış, Yanlışlık, Yanlış Kanı, Yanlış Düşünce

ESSENTIAL It is essential that parts are installed as a set.

Önemli, Gerekli, Şart, Başlıca, Esaslı, Esas

- 39 -

ESTABLISH Three levels of sensitivity classification are established for electrostatic discharge sensitivity devices.

Sağlamak, Tesis Etmek.

EVEN The lower temperature allows oil quenching, or even gas quenching with a protective atmosphere.

Hatta, bile, dahi, eşit, düz, düzlem

EVERY After activation, the ELT transmits a signal every 50 seconds for 520 milliseconds.

Her, Herbir.

EVIDENCE A detailed inspection searches for evidence of irregularity using adequate lighting and where necessary, inspection aids such as mirrors, hand lens, etc.

İbare, İz, Kanıt, Delil

EXAMINATION A detailed inspection is an intensive visual examination of a specified detail, assembly or installation.

Kontrol, inceleme, muayene, sınav,İmtihan

EXAMINE Disconnect dust cap from coupling and examine both for contaminants and damage.

Kontrol etmek, İncelemek , Gözden Geçirmek , Sınamak

EXAMPLE

For example, an aluminum fastener in contact with a relatively inert titanium structure may corrode severely,

Örnek

EXCEED

When the atmospheric pressure exceeds the cabin pressure, the atmospheric pressure acts on the valve poppets balance diaphragm which causes the valve poppet to raise off of the poppet seat.

Aşmak, Geçmek,

EXCEPT Double twist safety wire method is required for all safety wiring except when single wire method is specified.

Hariç Bırakmak, Dışında Bırakmak, Hariç, Dışında

- 40 -

EXCESS

All traces of excess lubricant and oil should be wiped from IDG to prevent being mistaken for leaking oil.

Aşırı , Fazla , Aşmak

EXCESSIVE Remove excess corrosion inhibiting compound from moving parts with a clean dry rag. Excessive buildup could harden at love temperatures and cause operating difficulties.

Fazla , Aşırı

EXCHANGER Care must be taken not to drop anything into the heat exchanger.

Değiştirici

EXHAUST Make sure that fuel which has become gas can be seen as it comes from the exhaust.

Egzoz, Tüketmek, Çok Yormak

EXIST When the aircraft is on the ground and the outflow valve is full open, the Pressure Valve opens to ensure a minimal differential pressure exists across the pressurized area.

Mevcut Olmak, Var Olan.

EXISTING Insert shaft assembly through existing bushings on each side of flow divider

Var Olan, Mevcut

EXPOSE Failure to remove residual Skydrol from exposed surfaces may result in demage to aircraft and equipment

Maruz Kalma, Temas Etme, Açmak, Korunmasız Bırakma

EXPOSURE İt is the sole responsibility of the user to ensure protection from injury or exposure to dangerous materials.

Maruz Olma, Açık Olma Maruz Kalma, korumasız

EXTEND The elevators are constructed from epoxy graphite and they extend from Butt Line (BL)5 - BL 200.

Uzanmak, Boydan Boya Uzatmak, Germek, Yayılmak, Çıkıntı Yapmak

EXTENSION This section covers the use of adapters or extensions when torquing aircraft tubing and fitting assemblies.

Ara-Uzatma Kolu-Çubuğu, uzatma, Uzanma, Yayma, Genişletme

- 41 -

EXTERIOR Static can build up over the entire exterior of the aircraft.

Dış, Harici, Dışarıdan gelen, Dışarıda Olan, Dış Görünüş

EXTERNAL Shut down both engines or if external hydraulic power is used, disconnect external hydraulic power.

Harici, Dış

EXTINGUISH Verify a fire extinguisher is present and serviceable,

Yangın Söndürücü: Yangın Söndürme Aleti

EXTINGUISHER Install safety wire on emergency equipment (guarded switches, fire extinguishers, oxygen regulators, etc.)

Söndürücü, Yangın Söndürücü

EXTRACTOR Remove defective display using extractor, P/N 540345-001 or equivalent.

Sökücü, Çıkarıcı, Bir Şeyi Çekip Çıkarmak İçin Kullanılan Takım

EXTREME Under extreme conditions of humidity, temperature and atmospheric conditions due to geographical location, the frequency of corrosion inspections may vary.

Aşırı.

EYE Injuries to eyes can happen if proper eye protection is not used.

Göz.

FABRIC In aircraft construction, reinforcing fabric is generally available in 3 styles.

Kumaş, bez

FACE Use eye protection and a face mask during this operation.

Yüz, çehre, görünüş, şekil, bakmak, karşılamak, örtmek, kaplamak

- 42 -

FACILITATE Removal of covers or floor panels may be required to facilitate maintenance on other airplane components in the tailcone.

Kolaylastırmak, rahatlatmak, yardım etmek

FACING Seats installed in seat positions 7 and 8 are always forward facing and seats installed in position 9 and 10 are always aft facing.

Bakmak, bir yöne bakmak, yüzünü dönmek, yüz, yüz yüze, kaplama

FACTOR An air leak in the main entrance door seal system may be a contributing factor of low pneumatic supply pressure.

Etken, unsur

FAIL

Too much sealant results in fastening problems and extensive cleanup, where as too little sealant will fail to provide adequate squeeze out required.

Sağlayamamak, başaramamak, yapamamak, arıza yapmak,

FAILURE Failure to install proper protective caps and plugs on electrical connectors may result in damage to equipment.

Takmamak, yapmamak, etmemek, ihmal etmek, hata, arıza

FALL Ensure hardware does not fall into APU air intake when removing air inlet.

Düşmek, Dökülmek

FAR Install bonding clamps as far away as possible from end of ducts.

Uzak , uzağa , öte , çok , bir hayli

FASTENER A bond is an electrically conductive joint. Bonds are assembled either directly, using fasteners and / or clamps or indirectly by using bonding straps or bonding wire.

Bağlama parçası, tutturucu, bağlayıcı, Perçin, vida, tespit,

FATIGUE Normal fatigue occurs when metal becomes weaker under repeated stress.

Yorgunluk, yorulma

- 43 -

FAULT The built-in test system reports any major fault, such as loss of an antiskid component, directly to the flightcrew.

Arıza, hata, kusur, eksiklik, sorun,

FEATURE The nose landing gear safety features are used to prevent inadvertent retraction of the landing gear.

Özellik

FEED This fuel then flows through fuel feed lines to the APU and the engine low-pressure fuel pumps.

Beslemek, yerleştirmek

FEEDBACK The engine speed control system uses feedback from the sensors to provide the ECU information necessary to control the systems and subsystems of the APU.

Geri besleme, sinyal, bilgi,

FIELD A defect or interruption in or close to the surface causes a disturbance in the magnetic field lines.

Alan, saha, dal

FILE Any load errors present will be displayed below file. Contact surfaces of cell terminals may be polished with fine file or emery paper.

Dosya, Eğe.

FILL FILLER

Fill the wash tank with the washing solution.

Doldurmak, dolmak, kaplamak, Dolgu malzemesi

FILTER ELEMENT Examine fuel filter element for contamination. If contamination is found, replace dirty element.

Süzgeç, süzmek, süzülmek, süzgeçten geçirmek, geçmek,

FIND/FOUND The technician will often find such items as rivets, nuts, bolts and plumbing fittings referred to as 'AN parts'.

Bulmak, bulunan

FINE Molybdenum gives a fine grain structure and makes the steel stronger without affecting ductility or workability.

İyi, ince, keskin, yıllanmış

- 44 -

FIT FITTING

Do the general visual inspection of the fuel tubes and fittings.

Uymak, tam oturmak, Bağlantı, tertibat, tesisat, uygun, doğru

FIX Fix any conditions noted when inspecting ribbon heater installation in Step 1.B.

Düzeltmek, Tamir etmek, düzenlemek, sabitleştirmek,

FLAME

Solvents shall be considered flammable and shall not be exposed to flame or spark under any circumstances.

Alev, yalaz

FLARE The close fit between the inside of the flared tube and the flare cone of the male fitting provides the actual seal.

Havşa, parlama, ışık

FLAT A flat heat blanket should not be used on a curved surface.

Düz

FLEXIBLE Thermoplastic materials are generally flexible and relatively soft.

Esnek, elastik

FLOAT The lighter slag floats on top of the iron.

Uçuşmak, yüzeyinde dolaşmak, yüzmek

FLOOR Conductive flooring areas must be free of all wax or other nonconducting coatings.

Taban, döşeme, yer, zemin,

FLOORBOARD NOTE: Adjacent floorboard may be removed if interior outfitting prohibits opening 1C floorboards.

Zemin, duvar veya yer kapağı, kaplama, döşeme, taban, yer,

FLOW The electron flow is from anode through metal path to cathode as described previously.

Akmak, akıntı, akım, akış

- 45 -

FLUID All flammable fluids should be kept in a secure flameproof store.

Sıvı, akışkan

FLUSH Flush heat exchanger primary internal passages with hot water (100°F minimum) for 15 minutes.

Bol/basınçlı su ile yıkama fışkırma , fışkırtma,

FOAM Apply the foam uniformly over the surface to be cleaned.

Köpük, köpürmek

FOLLOW FOLLOWING

The following pages show an extract of Chapter 51 of the 'Strnctural Repair Manual’.

Takip etmek, müteakip, takip eden

FORCE CAUTION: Using too much force when installing connector can cause demage to connectors and or pins.

Güç, kuvvet, zorlama,

FORM On a connection utilizing any form of stop nut (elastic or otherwise), amend torque value as follows:

Biçim, görünüş şekil, biçim verme, şekillendirme,

FORMAT The CVR converts the analog signals to a digital format and stores the data in solid state memory.

Biçim, şekil.

FORWARD Tighten forward bolt and torque to 270 inch-pounds

Ön, öndeki, ileri, ileriye, öne doğru,

FRAME Insert bolt and washer through inboard frame and bolt and sleeve through outboard frame.

Çerçeve, iskelet, gövde, çerçevelemek

FRAY Check for belt fraying or damage which would cause belt function to be in doubt.

Yıpranma, kavga, arbede, çekişme, yarışma, tartışma, yıpranmak, aşınmak

- 46 -

FREE The fuel filter element supplies contamination free fuel to the high-pressure pump,

Arındırılmış, muaf, serbest, rahat, temiz, özgür

FREELY If ball is damaged or does not move freely, replace or repair valve as necessary.

Serbestçe, rahatlıkla, özgürce,

FREQUENCY As explained previously, the extent of corrosion attack is almost always inversely proportional to frequency of cleaning.

Sıklık, zaman aralığı, salınım, frekans

FRICTION Bungee will be safetied during friction test.

Sürtünme.

FUELING NOTE: Fuel pit is preferred, but a fueling truck can also be used.

Yakıt doldurmak, yüklemek

FUNCTION The function of the turbine section system is to create and then convert heat energy into mechanical (rotational) energy,

İşlev, görev,

FUNCTIONAL Perform Landing Gear -Functional Test

Çalışma, faaliyet, işlevsellik,

FURNISH The hydraulic system furnishes hydraulic fluid under pressure to operate components such as landing gear, flight controls and brakes.

Vermek, sağlamak, döşemek, donatmak

FURTHER If aileron travel readings agree, the rigging has not been disturbed and no further rigging is required.

Daha fazla.

FUSE Check for spare fuses and current limiters in a bag on the inside of the junction box cover.

Sigorta, devre koruyucu,

- 47 -

FUSELAGE The external hydraulic power ground test connections are located between Fuselage Station (FS) 709 and FS 810,

Gövde, uçak gövdesi,

GAGE/GAUGE The measuring tools may include an optical micrometer, ultrasound, depth gages, etc.

Gösterge, (Basınç, vb.) ibreli gösterge, ölçme aleti, ölçer,

GAIN ACCESS Gain access to battery switch on outside of aircraft through access door 113AL.Lift antenna up to gain access to disconnect electrical connector on antenna.

Ulaşmak, erişmek, yer kazanmak, yer açmak yer sağlamak, ACCESS: giriş,

GALLEY The potable water system is an air pressurized system suppling water to the lavatories and galleys.

Mutfak , lavabo

GAP The filler is applied to all gaps and voids on the LP ( low Pressure) compressor case Assembly A.

Boşluk, aralık, yarık

GASKET Form-in-place gaskets are gaskets formed with sealant between a fixed and removable part.

Conta

GEAR GEARBOX

A 40 kVa generator is mounted on the APU gearbox for use on the ground or in flight when a primary electrical power source is not available.

Dişli, Dişli kutusu,

GENERATE Electrostatic discharge is a release of stored electrostatic charge, which has been generated by actions such as contact, rubbing or separating materials.

Üretmek, oluşturmak.

- 48 -

GENERATION During normal operations, the IDGs are the primary power generation sources.

Üretim; meydana getirme, kuşak, nesil,

GENERATOR Start Auxiliary Power Unit (APU) and apply electrical power to aircraft using APU generator.

Üreteç, üretici

GENERIC The following generic information is provided to assist the maintenance technician.

Genel, kendi cinsine ait, özgün

GLAND A buildup of lubrication in the O-ring glands may prevent the O-ring from sealing properly.

Etli kısım, kenar, bilezik, tozluk, kapak.

GLARESHIELD Verify annunciator on left glareshield and left flight panel are on full bright.

Glareshield (pilot mahalli ön cam eteği)

GLIDE The Glide Slope receiver is the part of the ILS (Instrument Landing System) that supplies vertical guidance in relation to the glide path of an aircraft approach.

Süzülme.

GLOBAL The SDU has a system table in memory that contains the global positions of all network satellites.

Küresel

GLOVE Be careful if you must do work on hot components. Use approved gloves and protective clothing.

Eldiven

GRAVITY CENTER OF GRAVİTY

Adjust engine lifting sling as necessary for proper center of gravity of entire engine, taking into account engine configuration

Yer Çekimi , Ağırlık , Önlem Ağırlık Merkezi

- 49 -

GREASE Lightly coat packing with silicone grease and sensorthreads with thread compound.

Gres, katıyağ, Yağlamak

GREAT Glass fibres and mat have great strength for their weight, but lack rigidity.

Büyük, meşhur, ala

GROOVE Install O-ring on coupler body O-ring groove.

Yiy , oluk , kanal.

GUARD Remove APU FIRE EXT switch guard.

Koruma, koruma kapağı, emniyet,

GUIDANCE The automatic flight control system supplies flight guidance in pitch and roll to recover from a wind shear condition.

Yönlendirme, rehberlik etme, yardım, sevk ve idare eden,

GUIDE This procedure will give only general guide lines for assembling and disassembling a Gamah coupler.

Kılavuz, rehber,

HALF Adjust borescope insertion tube to examine walls of top half of combustor

Yarım , yarı

HANDLE WITH CARE The static tester should be handled with care to prevent demage to equipment.

Özenle davranmak, sap, ustalıkla kullanmak, taşımak, kol, kulp,

HANDSET Location of installation and color of the handset is optional.

Ahize,

- 50 -

HARD The impact switch is factory calibrated to close in excess of 2.5 G in order to ignore nuisance trips from hard landings.

Sert, sıkı.

HARDOVER A detectable jerk is felt in control wheel as actuator hydraulic pressure is shut off automatically by hardover prevention system hydraulic valves.

Sıkışma, yavaşlatma fonksiyonu

HARDWARE Check all circuit breaker connecting hardware and ensure it is tightened securely.

Donanım, bilgisayar aksamı, silah, madeni parça-eşya, hırdavat,

HARNESS Control wheel electrical harness runs through washer and nut.

Kablo demeti.

HAZARD Aircraft structures, equipment, and personnel are protected from hazards of lightning discharges.

Tehlike.

HEADSET The VOICE mode supplies high quality audio signals for the headsets and flight compartment speakers.

Kulaklık

HEAT HEATER

Remove floor heater mats, if installed.

Isı, Isıtıcı, ısıtma,

HIGH HEIGHT

Use hoist to lift inlet cowl to correct height.

Yüksek, Yükseklik.

HINGE Shut off valve consist of a main valve housing, two semicircular flappers hinged on a pin.

Menteşe ile tuturmak, menteşe, dayanak noktası, destek,

HOIST Remove rudder hoist from rudder.

Kaldıraç, vinç: Pervane indirme ve bindirmede kullanılan aygıt.

- 51 -

HOLD While holding backing nut, remove bolts, lock washer, washer and electrical cables from current limiter,

Tutmak, taşımak, bulundurmak.

HOLE

Align the slots of the shaft with the holes of the compressor disc.

Delik, oyuk.

HONEYCOMB Use care not to direct high pressure air on honeycomb surfaces.

Petek, petekli doku- yapı, uçak kaportasında kullanılan balpeteği yapı.

HOOK Make sure the hook is installed correctly, then hand tighten the fasteners.

Çengel, kanca, asmak, çengellemek,

HORIZON The standby horizon is an electrically driven gyro whose vertical attitude is maintained by a mechanical erection system.

Ufuk, ufki durum göstergesi

HORIZONTAL Lower engine until transit stand trunnions engage and are horizontal in the front support clamp blocks.

Yatay, ufuk çizgisine paralel

HORN The selftest uses the Main Landing Gear horn tone.

Korna, boynuz.

HOSE The optimum fueling hose pressure should be between 35 and 55 psi.

Su hortumu, hortum, hortumla sulamak,

HOUSING The probe housing has a hermetic seal that protects the internal sensor from contamination.

Yuva,

HOWEVER However it may deteriorate if attacked by fungus or it may be damaged by insects.

Ancak, ama, oysa, halbuki

- 52 -

HYPER Pressurizing the aircraft on the ground, turns the aircraft into a hyperbaric chamber.

Aşırı, yüksek basınç

ICE / ICING Icing conditions can be expected to occur when visible moisture is present such as cloud or fog with low visibility, rain, snow, sleet etc.

Buz, Buzlanma

IDENT Identify and tag tubes attached to pressure relief valve before disconnecting.

Belirlemek, tanımak ve isimlendirmek, teşhis,

IDENTICAL Operation of the precheck valves for the left and right tanks is identical.

Aynı, aynı şekilde, benzer.

IDENTIFY If installing a new switch, identify wires and attach to switch terminals with screws

Tanıma, teşhis etme, belirleme bulma, tespit etme, etiketlemek

IDLE Operate the engine at idle speed for 5 minutes.

Boşta, yüksüz çalışma, rölanti

IGNITER Do not touch or remove igniter plugs leads at least 2 minutes after electrical power is removed from APU. İgnition exciter can hold electrical charge during this time.

Ateşleyici, tutuşturucu, yemleme barutu, tutuşturma tertibatı

IGNITION Do not use the lubricant near sources of ignition.

Ateşleme, kontak, tutuşma, tutuşturma

ILLUMINATE Use a portable light to illuminate the air/oil cooler transfer tubes when checking for leakage.

Açıklamak, aydınlatmak, ışıklandırmak

- 53 -

IMMEDIATELY During this check it is possible engine operation can become unstable. Decrease engine power immediately if this condition occurs.

Derhal, hemen

IMPACT Inspect engine upper cowl door forward and aft edges for delamination and impact damage.

Çarpma, vuruş, darbe, vurma, etki, şok,

IMPROPER Check only cool tires at least two to three hours after a flight. Use an accurate gage; inaccurate gages are a major cause of improper inflation.

Yanlış, uygunsuz, hatalı, uygunolmayan, yakışıksız, çirkin.

IN ACCORDANCE WITH Record all maintenance actions in accordance with current Federal Aviation Regulations.

Uygun olarak, e göre, bağlı olarak

IN CONJUNCTION WITH The following procedure is used in conjunction with Fig.1

ile bağlantılı olarak, ile birlikte,

IN THE EVENT OF A manual release button will permit the handles to be pulled in the event of a selenoıd failure.

Olması durumunda, takdirde halinde

INBOARD Install transit stand trunnions on inboard and outboard sides of engine.

İç, iç gövde, iç kısım

INCLUDE This section includes general information and procedures for the application of external hydraulic power.

İçermek, kapsamak, dahil etmek, hesaba katmak,

INCORPORATE The wrist strap incorporates a 1 megohm current limiting resistor in series with the ground cord to protect the wearer from electrical shock.

İçinde barındırmak, dahil etmek , kapsamak, birleştirmek.

- 54 -

INCORRECT If pressure incorrect, service cylinder to 6 psig, using a dry air or nitrogen servicing cart with a regulated pressure output not to exceed 12 psi.

Doğru olmayan, hatalı, yanlış

INCREASE When the engine has stabilised at MIN IDLE slowly increase the engine speed to 65 percent.

Yükseltmek, arttırmak, çoğalmak, yükselmek, artırmak, çoğaltmak,

INCREMENT If oil level is not visible in sight glass, add oil in ½ pint increments until level registers, then fill tank.

Arttırma, kademe kademe ekleme, artış, artma

INDEPENDENT Both Air Condition Controllers contain two independent zone control channels to control the temperature.

Bağımsız.

INDEX Make an index mark on rudder and aileron control rods on the forward face.

Yer belirleme, yer gösterme, tanıtma,

INDICATE Verify all three temperature displays indicate approximately 33°F - 42°F.

Göstermek, belirtisi olmak, göstergesi olmak, sinyal vermek

INDICATION If amber or red temperature indication is noted, the rheostat should be returned to the previous position immediately.

İkaz, uyarı, görüntü, işaret.

INDICATOR Landing gear position is provided by indicators on the landing gear control panel.

Gösterge,

INDIVIDUAL From the cold air manifold, the air is available for delivery to the individual outlets and overhead gaspers.

Her biri, ayrı, kendi,bireysel, kişisel, özel, tek tek,münferit

INDUCE High stresses can be induced by binding of the spring on the arbor.

Indüklemek

- 55 -

INERTIAL Remove the handset and inertial reel assembly.

Atalet, hareketsiz, durağan

INFORMATION The drawing is the most important means of information and communication used in engineering.

Bilgi, malumat

INHIBIT Apply coat of corrosion inhibiting compound to bolt and washer prior to installation.

Engellemek, önlemek, tutmak, bırakmamak, mani olmak.

INHIBITION Apply corrosion inhibiting compound to the exterior of mated connector.

Önleme, yasaklama, engelleme.

INITIAL Initially it will be about 28 Vdc and current will be about 38 amps.

İlk , başlangıç , birinci, ilk anda

INITIATE Pressurization controller will initiate a test on channel 1 first, there will be a slight delay, then it will initiate a test on channel 2.

Başlamak , başlatmak

INJURY Warning: Faılure to remove hydraulic and electrical power from aircraft may result in serious injury or death.

Yaralanma

INLET Install inlet cover on compressor inlet duct and attach with tape.

Giriş

INNER The window assembly has a heater grid bonded to its inner surface to eliminate the formation of condensation or ice on the window.

İç, içerdeki, merkeze en yakın

INNERLINE Innerline heaters protect the supply and drain lines from freezing conditions.

İç kısım, iç hat, dahili hat.

- 56 -

INPUT Steering control inputs come from the tiller assembly and either set of rudder pedals.

Veri, bilgi, girdi, giriş

INSERT Hold gasket and check valve in place and insert screws with washers from forward side.

İçeri sokmak, yerleştirmek, ortasından, geçirmek,

INSIDE Wrinkles are acceptable along the inside radius of bent / formed tubing, providing the depth of the wrinkles do not exceed the maximum depth.

İç, iç kısım, İçerde, içeriye, İçerisine, içinde

INSPECTION NOTE: Inspect Pressure Relief Valve (PRV) in accordance with manufacturer’s inspection periods.

Teftiş etme, muayene etme, kontrol etme, denetleme, bakım

INSTALL INSTALLATION

The wings are installed and the attachment bolts are torqued to the specified limits.

Kurmak, yerleştirmek, monte etmek, takılı, monteli

INSTRUCTION Do not do electrical checks into the Electronic Equipment Controller. If you do not obey this instruction, damage to the EEC can occur.

Öğretim, talimat, yönerge.

INSTRUMENT These hoses are used on instrument systems, vacuum systems and autopilots.

Gösterge, aygıt, alet, cihaz, Belge

INSULATION Insulation material is applied to conductors by one of two basic methods; extrusion and wrapping.

Yalıtım, tecrit, yalıtım maddesi, malzemesi

INTAKE The minimum safety distance in front of the air intakes is 6 m (during start up) or 4 m with the engines at idle.

içeri alınan miktar yada giriş , alık

INTEGRATE The hand pump pressure tester on the top is a typical hose tester with integrated reservoir.

Bütünleşmek, kaynaşmak, katmak, kaynaştırmak

- 57 -

INTEGRITY These tests are designed to assure the operational integrity of the unit.

Bütünlük, tutarlılık, güvenilirlik.

INTEND This procedure is intended to aid the technician in configuring the aircraft for safe ground maintenance.

Niyetiyle oluşturmak, tasarlamak, planlamak, niyetinde olmak,

INTENSIVE A detailed inspection is an intensive visual examination of a specified detail, assembly or installation.

Yoğun , yoğunluk

INTERFACE Ensure all electrical and electronic interfaces between aircraft, APU and APU electronic control unit are correctly installed.

İçiçe geçen bağlantılar, Birbirine geçen bağlantı noktaları,

INTERFERENCE Check entire length of cables to insure correct routing and no interference with other cables.

Engelleme, karışma, müdahale. çatışma , engel, girişim

INTERMEDIATE Attach forward end of engine lifting sling to intermediate case with pin and safety clip.

Arada bulunan , ara ,orta

INTERNAL As the electrical current increases, the internal flapper moves to increase the supply area and reduce the vent area.

Dahili, iç,

INTERVAL A 15 minute interval is necessary to allow starter to cool. Starter must not be operated again until 15 minute interval is complete.

Ara, mola, aralık

INTRODUCE INTRODUCTION

A common standard screw thread agreed and introduced by Britain,

Takdim etmek, takdim, tanıtım

- 58 -

INVALID If input data becomes invalid, the last inputs are retained in memory until the data is changed by the use of selector knobs

Hatalı , hükümsüz , geçersiz

INVERTER The 50 amps dc power is used to power the E-inverter for essential ac loads.

DC takatı AC takata çeviren cihaz.

IRREGULARITY Inspect for evidence of irregularity, damage or deterioration.

Bozukluk, Düzensizlik, aksaklık, düzensizce ,dengesiz

ISOLATION Continue breaking the circuit until the defect can be isolated down to loop or aircraft wiring.

Ayırt etmek, yalıtım, ayırmak, tecrit etmek, (arıza) bulma, ayırt etme

ISSUE Periodically, the manufacturer shalll issue an index of service bulletins (SBI).

Göndermek, yayınlamak, Dagıtmak, Sorun, konu

ITEM Illustrated Parts Catalogue shows items considered to be replaceable during the service life of the aircraft.

Madde, parça,

JAM The flap actuators contain mechanical force limiters which protect the flap actuators and flaps in the event of a mechanical jam

Sıkışıklık, tıkanıklık, Bastırmak (Radyo mesajını) bozmak

JOINT Exercise care around landing gear joints and bushings so the protective cover of old grease is not removed.

Eklem, mafsal, birleşim noktası, eklem yeri, bağlantı noktası, yeri

- 59 -

JUMPER Install a jumper wire between connectors on any one of thermal sensors.

Kısa devre , köprü

KEEP To prevent grabbing, keep a firm grip on the saw handle at all times.

Muhafaza etmek, korumak

KNOB Fully exercise rudder system using rudder trim control knob.

Düğme, kumanda topuzu, anahtar

KNOW / KNOWN Semi - rigid pipes are also known as tubes or tubing and can be bent to shape and are often flared for connectors.

Bilmek/ Bilinen

LABEL When you remove an Magnetic Chip Detectors, you must attach a label to show the position from which it was removed.

Etiket, etiketlemek, tanımlamak, yapıştırmak, nitelendirmek

LADDER Damage to tail compartment ladder may result if door is not properly secured during aircraft towing.

Merdiven; el merdiveni.

LAMP Heat can be applied by using infrared lamps or heated air.

Lamba

LARGE The large washer is installed next to the bell crank and the small washer is installed next to the nut.

Geniş.Büyük

- 60 -

LATCH Connect latching devices to hooks on front of DFDR and tighten securely.

Kapı kilidi, kapı mandalı kilitlemek, mandallamak

LATERAL The autoflight system receives computed lateral (roll) and vertical (pitch) steering commands from the FD system for the autopilot and for display on the Primary Flight Display.

Yanal, Yandan gelen, yana doğru

LAVATORY Areas subjected by battery acids, lavatory spills, smoke and exhaust fumes require closer attention and more frequent maintenance.

Hela , tuvalet , lavabo

LAYER Minor scratches in the tempered glass outer layer are common on windshields due to erosion.

Katman, tabaka, kat

LEAD Laboratory examination of engine filter elements will often give a useful lead to the source of breakdown

Rehber, rehberlik önderlik etmek, ara kablosu, kurşun, kılavuzluk,

LEAD LEADING EDGE

Failure to remove restrictor support tube could lead to an unsafe condition and serious or fatal injury to person.

Yol açmak, meydana getirmek, Hücum kenarı, ön kenar, ön kısım

LEAK Dripping leaks from accessible seals shall be cause for seal replacement.

Sızıntı, sızdırmak, ızmak

LEAST

T h e l i n e r m u s t b e s m o o t h t o o f f e r t h e least r e s i s t a n c e t o f l o w , a n d r e m a i n f l e x i b l e t h r o u g h o u t a n e n t i r e r a n g e o f o p e r a t i n g t e m p e r a t u r e s .

En az,

LED This LED will go off when the input voltage falls below 94 Vac or for a fault within the charger.

Led lamba

LENGTH Install the tying cord at least every 2.00 in along the length of the harness.

- 61 -

Uzunluk, boy, parça

LEVEL Table 202 identifies some typical electrostatic charge levels and actions that can produce electrostatic charge.

Seviye, düz, yatay

LEVER A fulcrum is the support arround which a lever rotates.

Kol, manivela,kaldıraç

LIFT Lift the engine from the transit stand, then pull the transit stand clear of the engine.

Kaldırmak, yükseltmek Asansör, kaldırıcı kuvvet,

LIFTING Make sure the hoist is installed to the correct lifting eye.

Taşıma, kaldırma, kaldırıcı

LIGHTNING The Lightning Protection diodes are replaced by types that have a higher voltage.

Şimşek, Yıldırım

LIMIT Make sure the dimensions of the dry film lubricant are in limits.

İstenilen sınır, uç, sınır, kısıtlamak, sınırlandırmak

LIMITATION There is no limitation on duration of wing anti-ice operation during flight.

Tahdit etme, sınırlama

LINE Draw a thin line approximately in the middle of the board along the aligned rule.

Hat, çizgi, bağlantı

LINEAR In setting and checking control surfaces, either linear or angular position of surface may be measured.

Doğrusal.

LINK The butterfly plate is directly linked to the actuator assembly through the actuator linkage.

- 62 -

Bağlamak, tutturmak, bağlantı, irtibatlamak

LINKAGE The elevators are controlled by a direct linkage from the pilot or copilot control columns.

Bağlantı, irtibat çubukları, mafsal, dizi, silsile.

LINT Wipe all parts and surfaces with a clean, lint-free cloth.

Pamukçuk, iplik, keten tiftiği, sargı bezi

LIQUID These materials are volatile liquids which may be sprayed or brushed on the surfaces to be treated.

Sıvı, mayi, seyyal, akıcı, su gibi akan, akışkan, akar.

LOAD If the tanks are fueled with one wing lower than the other, the fuel load in the wing tanks may not be balanced.

Yük, yüklemek, doldurmak,

LOCAL It is recommended that local tower be notified when testing air traffic control system outside hangar.

Yakın çevre, civar, bölgesel, yerel, mahalli (piyasa, satın alma)

LOCATE TEMP CONTROL panel is located in the cockpit overhead panel.

Yerleşmek, yerleştirmek, Yerini bulmak

LOCK The lock spring automatically disengages when the union nut is unscrewed.

Kilit, Kilitlemek

LOGIC The BPCU also supplies power and control logic for most of the ac and dc contactors.

Mantık

LONG LENGTH

Holding that temperature long enough allows constituents to enter into solid solution.

Uzun Uzunluk

LOOP The ends are cut to suit and twisted together to tension the loop.

- 63 -

Döngü, düğüm, ilmik, ilik

LOOSE NOTE: If left wing cable is not being removed, only loosen left wing cable turnbuckle.

Gevşetmek, gevşek,

LOOSEN These safety devices are used on components that may loosen due to vibration or changes in temperature.

Gevşek, gevşetmek, çözmek, açmak, salıvermek

LOSS A material is considered to be heat-resistant if there is no significant loss of strength up to temperature of approx. 600 °C.

Kayıp

LOW Stainless steal conducts heat at a lower rate, which makes welding more difficult.

Düşük, alçak

LUBE Align previously lubed flexible boot to top of ram air duct.

Yağ, makina yağı, Yağlamak , yağlama

LUBRICANT Install new O-ring, lubricate with lubricant and install on vent valve.

Kayganlaştırıcı madde, yağ,

LUBRICATE The APU generator is cooled and lubricated by oil from the APU gearbox.

Yağlamak

LUBRICATION The lubrication system is a full flow recirculatory oil system.

Yağlama

MACHINE MACHINING

In the building of machines and apparatus, screws and bolts are the most used components.

- 64 -

Makine, işleme

MAGNETIC When only inspecting for presence of magnetic particles on magnetic plug of chip detector, remove only magnetic plug.

Mıknatıs tarafından çekilmek, çekilmek, mıknatıslı, mıknatıs, çeker, çekici

MAINTAIN MAINTENANCE

Sealing pressurized areas maintain cabin pressure at a minimum predetermined level under all flight conditions.

Sürdürmek, devam ettirmek, bakmak; idame ettirmek, muhafaza etmek. Bakım, idame

MAINTAINABILITY The use of a nonpressurized gearbox decreases the complexity and increases maintainability of the system.

Sürdürülebilirlik, idame, bakım yapılabilme durumu, imkanı.

MAJOR The distribution of dc power is accomplished by four major electrical buses.

Ana, esas, büyük , temel

MANAGEMENT Flight Management System (FMS) Data Management Unit (DMU)

Yönetmek, yönetim, idare Uçuş Yönetim Sistemi Bilgi Yönetim Sistemi

MANIFOLD Crack open the drain valve from the manifold block to ensure that all the air is vented from the pump.

Dağıtım borusu, kopya, çoğaltma

MANUAL Pilots should not exceed the flight manual limitations and should exercise great care during landing and taxiing.

Manuel, elle yapılan, kitapçık, el kitabı

MANUFACTURE MANUFACTURER

If sealant is to be mixed, it must be mixed by manufacturer’s instructions.

Üretmek, Üretici, imalatçı, imalatçı firma

MAP The system also identifies the contour of the ground (terrain) with a ground map function.

Harita

MARK Battery terminals, which have permanent marks for polarity, have different diameters and thus are not interchangeable.

- 65 -

İşaret,çizgi, belirti, iz, not, numara, etiket, numaralandırmak

MARKER Make a temporary mark on nose cone and nose cone fairing, with temporary marker to identify angular position of nose cone fairing and nose cone.

İşaret kalemi, işaretleyen şey, İşaretleiyci

MASKING Remove masking tape from around door frame.

Maskeleme, örtme, saklama gizleme

MASS The molten mass is only then allowed to flow into the compression mold.

Kütle, kitle

MAST Visually inspect overboard vent / ram air inlet mast from outside of aircraft for damage, cracks and corrosion.

Direk

MASTER A master minimum equipment list contains a listing of the allowable minimum serviceable equipment and systems.

MATING Push controller until electrical connector is fully engaged with mating electrical connector on mounting tray.

Birbiriyle eşleşen öpüşen, örtüşen, çiftleşen, birleşen

MEANS The flang attach the nuts to the movable table by means of nut tenons.

Araç, vasıta, vesile

MEASURE If excessive loss is measured in one direction only, it is probably a faulty connection.

Ölçü, miktar, oran, derece.

MEASUREMENT In some cases, leakage measurement becomes a problem because of location of component in aircraft does not permit direct observation.

- 66 -

Ölçüm, ölçü

MEDICAL In case of eye contact, flush with water and seek medical attention.

Tıbbi, tıbba ait, iyileştirici

MEMBER All fittings which require safety wiring shall be wired to mating part or an adjacent member.

Parça , unsur, mesnet , çubuk

MEMORY The Inertial Reference Navigation contains a magnetic variation topographical map in its memory.

Hafıza.

METAL Direct electrical bonds are frequently used for metal to metal joints.

Metal, maden

METER Fiber transition loss at the optical power meter is negligible because this output is presented directly to the detector of the meter, not to a fiber.

Ölçer, Ölçme aleti, metre, ölçü aleti, gösterge.

METERING The metering sections open to modulate the control chamber pressure.

Düzenleme, ayarlama, ölçme

METHOD This method identifies an ac source as it automatically comes on line.

Usul, yöntem.

MINOR Minor scratches in the tempered glass outer layer are common on windshields due to erosion.

Küçük, minik.

MIRROR Use the inspection lamp and the inspection mirror to examine all the anti-icing air duct connections.

Ayna, yansıtmak, aksettirmek

MISALIGNMENT Premature wear of control cables indicates a requirement for a misalignment check.

- 67 -

Yanlış ayarlama, yalnış hizalama

MISMATCH Ensure sealant completely fills gaps or surface mismatches.

Uyumsuzluk

MISSING Visually inspect fan inlet housing sheet metal for missing rivets. If rivets are missing, refer to Approved Repairs.

Kayıp, yitik, eksik, akıbeti bilinmeyen, namevcut,

MIX MIXTURE

For de-icing, a mixture of water and de-icing fluid is sprayed over the appropriate surfaces.

Karıştırmak, Karışım

MODE In the longitudinal wave mode, the particles vibrate in the direction of propagation.

Mod, tarz, biçim

MODULATION The anti-ice air modulating valve is a 1.5 inch butterfly-type shut-off and modulation valve.

Ayarlama, istenen duruma getirme,

MOISTURE At normal atmosphere temperatures, metals do not corrode appreciably without moisture.

Rutubet , nem

MOMENTARILY Momentarily depress switch if light is on and verify switch light goes off.

Anlık, geçici.

MONITOR Zone temperatures are monitored and controlled by the controller via zone supply duct temperature sensors.

İzlemek, takip etmek, gözlemek, gözetlemek

MOTION Wear in the throttle linkage results in lost motion and can cause low power and/or throttle stagger.

Devinim,hareket, işaret, işleme, çalışma, işaret etmek

MOUNT A 40 kVa generator is mounted on the APU gearbox for use on the ground or in flight.

- 68 -

Takmak; irtibatlamak, yerleştirmek, mesnet

MOVEMENT NOTE: Movement of control surfaces is required to ensure flow of hydraulic fluid through components.

Hareket, eylem, faaliyet, bölüm, kısım, mekanizma

MOVING Type VIII will serve as a lubricant for slow moving components.

Hareketli , haraket ettirmek

MULTIFUNCTION The pilot can override these values by making entries on the multifunction control display unit.

Çok fonksiyonlu

NACELLE The purpose of the nacelle subsystem is to house the engine and minimize aerodynamic drag of the engines while in flight.

Yuva, ev, motor yuvası, kaporta, kapalı gövde

NECESSARY If necessary, open landing gear doors using auxiliary hydraulic pump ground service handle.

Gerekli, lüzumlu,

NEED To meet these needs, stainless steels, titanium alloys and composite materials have come into being and are now serving as structural materials.

Gerekmek, ihtiyaç duymak, ihtiyacında olmak, gereksinim

NEUTRAL Pull control columns aft to neutral position and hold.

Nötr: Normal bir durumda ne pozitif, ne de negatif olan.

NEXT A new cable must be installed at the next shop visit.

Bir sonraki, en yakın, en bitişik, bundan sonra, onra

NICK Remove nick by blending, scalloping and/or hand polishing

- 69 -

Çentik, sıyrık, çentmek, sıyırmak

NOISE Note any unusual engine noise during engine operation.

Ses, gürültü, patirti,

NOMENCLATURE Vendor code numbers are used in the nomenclature column to identify the manufacturer of a part.

Malzeme ve teçhizata verilen resmi isimlerin listesi

NORMALLY The left IDG normally powers the left main ac bus and the right IDG normally powers the right main ac bus.

Normalde , genelde , normal olarak

NOSE Landing will become critical because of the nose-down tendency.

Burun

NOW

Şimdi

NOZZLE If Monobromotrifluoromethane is released accidentally, it will not cause damage to engine or cause a blockage in the nozzle.

Püskürtme memesi, boru ucu, hortum başı, başlık

NUT Surface rust can develop on steel nuts, bolts and other fasteners.

Somun

OBEY Obey all Electrostatic Discharge (ESD) safety precautions.

İtaat etmek, uymak

OBSERVE General engine operating limitations, oil system limitations and fuel system limitations are presented below and are to be observed during all engine runs.

Gözlemlemek, gözetlemek, Gözlemek, dikkatle takip

- 70 -

etmek, bakmak

OBSERVER Control all cockpit related aircraft audio services from the pilot, copilot and observer stations.

Rasıt, gözetleme yapan şahıs, gözetleyici, gözcü, gözlemci

OBTAIN To obtain proper required torque, install washers under the bolt head.

Elde etmek, sağlamak

OBVIOUS A general visual inspection is an inspection for obvious unsatisfactory conditions / discrepancies.

Görülen, gözle tespit edilen, bariz, açık, aşikar

OCCUPATIONAL Many of the materials specified here have significant occupational safety, health or environmental requirements.

İş, işle ilgili, işe dair, çalışamaya bağlı

OCCUR Galvanic corrosion occurs when dissimilar metals are in contact and external circuit is provided by presence of moisture.

Meydana gelmek, oluşmak

OFFSET Both sets of fins are offset periodically in the flow direction to increase flow turbulence and improve heat transfer.

Dengelemek, denkleştirmek, denge meydana getirmek

OFTEN Electronic systems very often employ racks and panels to house the components of the system.

Sık sık

OMNIDIRECTIONAL

Very High Frequency Omnidirectional Range (VOR) system contains components that may be damaged by Electrostatic Discharge (ESD).

Çok yönlü,

ONCE Once released, verify shoulder harness moves freely again.

ğinde, inde, bir kez , bir kere, bir zamanla

ONLY

- 71 -

Sadece, yanlızca

OPENING Inject sealant into wire bundle immediately behind connector backshell or through any openings in the backshell.

Boşluk, açıklık, delik, yarık, başlangıç, açılış kapı, açma, açış

OPERATE Differential pressure between duct inlet and duct venturi provides capability to operate valve actuator.

Çalıştırmak, harekete geçirmek

OPERATIONAL When replacing a module, operational software must first be loaded into other modules as follows:

Kullanıma hazır, kullanılabilir, faal, çalışır durumda

OPPOSITE If control rod is to be replaced, measure length of control rod from center of rod end to center of opposite rod end.

Diğer, çapraz, karşıt, zıt, karşı, diğer, karşısında

OPTION There are 3 options for viewing messages, they are as follows:

Seçenek, yol,

OPTIONAL Setting the parking brake is optional. If the parking brake is not set, the airplane can be relocated without entering airplane.

İsteğe bağlı, size bağlı,

ORDER The fan blades are to be fitted in the exact same order.

Sıra, düzen, tertip, durum, hal, Sipariş, kural, sınıf, tür, çeşit

OTHER

Diğeri, öteki, başkası

OTHERWISE This level of inspection is made from touching distance unless otherwise specified.

Tersi, aksi, olmadığı takdirde, aksi taktirde , başka türlü

OUTBOARD Remove trunnion blanking cover on outboard side of engine.

- 72 -

Dış, dış gövde, dış kısım

OUTER Inspect outer structure of heat exchanger for dents, cracks or discoloration.

Harici, dış, dıştaki.

OUTLINE Clean area around suspected leak. Allow 30 minutes to 1 hour for leak to wet exterior surface, then blow talcum powder on area. NOTE: Talcum will outline wet area clearly.

Ana hatlarını belirlemek, Çevresinde çizgi oluşturmak. Çevrelemek, taslak, ana hat.

OUTPUT The usual range of output voltages from the ignition exciter is 2000 -3000 Vdc

Çıkış, çıktı

OVERBOARD if the temperature of the cylinder reaches 225°F, the regulator will vent the cylinder overboard.

Gövde dışı , drenaj

OVERHAUL The oil chamber of a new or overhauled strut may be filled prior to the installation of the gear assembly.

Büyük bakım, gereken onarımı yapmak için elden geçirmek.

OVERHEAD Differential pressure on overhead panel should display less than 0.1 psi.

Tavan, baş üstü,

OVERHEAT Install all items removed to gain access to overheat thermostats.

Aşırı ısınma , hararet

OVERRIDE The aural warnings from other avionics systems that are more important will override the TCAS aural warnings.

Bastırmak, devre dışı bırakmak, üstün gelmek, önceliği almak,

OVERSPEED The GCU also provides fault protection for under / overfrequency, under / overvoltage and overspeed.

Aşırı dönüş, aşırı sürat, aşırı hız , aşırı devir

- 73 -

OVERTEMPERATURE When taxiing with a flat tire. Do not use excessive engine thrust. Also, monitor the interturbine temperature (itt) indicator for possible engine overtemperature.

Aşırı ısınma, aşırı sıcaklık, aşırı hararet,

OWN Each metal has its own re-crystallisation (or: annealing) temperature,

Sahip olmak, malik olmak, kendine ait, kendi

PAD Clean bonding and grounding surfaces thoroughly with a nonmetallic abrasive pad, fine or medium grade, then wipe clean with dry cloth.

Bez, Tampon, yastık, altlık, takoz, minder

PAGE The page numbering system used throughout the structural repair manual consists of the 3-element number plus the page number.

Sayfa

PAINT Remove all paint or lacquer from electrical bonding surface with MPK.

Boya , boyamak

PANE Completely cover outboard surface of window pane with masking tape.

Cam, Pencere camı,

PARAMETER Check engine parameters to see if engine surge occurs again

Değer, Parametre

PART PARTICLE

Do not use abrasives such as carbon steel, stainless steel or iron oxide sandpaper as they leave particles imbedded in surface or scattered in area causing corrosive action.

Bölüm, parça. Parça, zerre, tane

- 74 -

PARTICULAR Particular care should be taken to avoid splashing of fluids on the skin.

Özel, ayrıntılı.

PASSAGE Back flush heat exchanger primary internal passages with hot water (100°F) for 30 minutes.

Geçiş, geçmek

PASSENGER Pressure control system provides control, regulation and monitoring of cabin pressure to ensure maximum passenger comfort and safety.

Yolcu,

PATH Electrical power returns should be direct with the shortest possible path from the operating equipment to the ground.

Yol , hat, istikamet,

PEDAL Dissipate hydraulic system pressure by cycling flight controls and operating the brake pedals several times.

Ayaklık, pedal

PENETRATION Solvent penetration to cable core washes out lubricant and permits rapid wear and corrosion.

İçine işleme, nüfuz etme, girme; etki, tesir; feraset,zekâ, anlayış.

PERCENTAGE Speed is given as a percentage (%) of low-pressure shaft turning speed.

Yüzde.

PERFORM The Electronic Control Unit (ECU) performs four primary functions:

Yapmak,

PERFORMANCE Connectors will be inspected, cleaned, repaired or replaced for conditions that will impair connector performance.

Sağlamlık, dayanıklılık, güç, işlerlik, verim,

- 75 -

PERIPHERY Proper maintenance of the weather sealant around periphery of windshield will prevent moisture penetration.

Dış kenar, dış çerçeve, çevre, civar,

PERMANENT The depression will return to its original smooth surface with no permanent damage.

Sürekli, daimi

PERMIT If high vibration occurs and operational circumstances permit, one engine at a time may be quickly retarded to idle,

İzin vermek, müsade etmek, uygun görmek, bırakmak

PERPENDICULAR A closed valve shows the line in the circle perpendicular to the system line.

Dik, dikey, dikey çizgi, dikey, dikme

PHASE A 40 kVa generator produces three-phase, 400 Hz, 115 Vac power.

Faz, safha, evre, aşama

PIECE It is acceptable to place a piece of tape over shaft opening in resolver housing to prevent shaft rotation.

Parça, kısım

PILLOW Pay particular attention to areas around flap tracks, flap actuator fittings and pillow block support structures.

Yastık, yastık vazifesi görmek

PITCH The flight control system provides aircraft pitch, roll and yaw control around the three axis (lateral, longitudinal and vertical) in all phases of flight.

Yunuslama hareketi yapmak, diş açıklığı, oluk, kanal, yarık, kertik.

PIVOT The horizontal stabilizer pivots to change angle of incidence as flaps are extended or retracted. Angle of incidence; Geliş açısı.

Mil veya eksen üzerinde dönmek-mil üzerine yerleştirmek, Saplama, mil, eksen, muylu, destek, dayanak

PLACARD Interior placards are installed throughout aircraft and identify components, exits and other aircraft equipment.

Bilgi levhası, levha, afiş, ilan, pankart, poster, etiket

- 76 -

PLACE If an amber or red temperature indication is noted, immediately place the rheostat in the full cold position.

Konumuna, durumuna getirmek, koymak, yerleştirmek, yer

PLANE Adjust engine lifting sling until engine is nose down (slightly), relative to horizontal plane.

Düzlem.

PLATE Corrosion will be less on painted, aluminum coated or aluminum plated surfaces than on unprotected surfaces;

Levhalama, levha, sac veya metal ile kaplamak, sac, disk, kaplama

PLUNGER The micro plunger switches are adjustable and are so well adjusted that the lamp will not receive 28-volt DC power until the landing gear door is fully open.

Saplama, çubuk, dalgıç pompa pistonu, dalma pistonu, hareketli göbek

PNEUMATIC Disconnect pneumatic line from shut-off valve.

Pnömatik , havalı

POINT The size of washer is another point to consider in bolted connections.

Nokta, konu, dikkat edilmesi gereken nokta, mesele, uç, sivri uç

POINTER The indicator pointer will reflect the relative position of the valve butterfly as it is moving.

İbre, Gösterge

POISONOUS Engine oil is poisonous and can be absorbed into body.

Zehirli

POP If red indicator button does not pop, filter is satisfactory.

Dışarı yukarı doğru yuvasından atmak, sigorta v.b. nin atması.

- 77 -

POPPET The spring closes the poppet valve and valve O-ring engages the valve body to stop fuel flow.

Konik, by-pass butonu.

PORT There are six primary flow duct connections and two low limit valve sense ports.

Hat, hatta yönlendirmek

PORTABLE The aircraft is equipped with two portable fire extinguishers.

Portatif, seyyar, taşınabilir, nakli mümkün

PORTION If friction levels remain out of limits,It may also be necessary to isolate portions of the individual, left and right systems.

Bölüm, parça, kısım, Oran, mukayese, karşılaştırma, nispet

POSSIBLE POSSIBLY

This section identifies various known types of corrosion, causes and possible consequences if corrosion is allowed to continue without corrective action.

Muhtemel, olası, olanaklı, mümkün, makul, akla yakın

POST The two NO GND SPLRS lights are located on the cockpit windshield center post.

Direk, kiriş, yerleştirmek, dikmek.

POTABLE The potable water system is designed to store, dispense and drain 30 gallons of fresh water used in lavatories and galleys.

İçilebilir, içmeye uygun,

POWERPLANT The powerplant system is a single-shaft constant speed gas turbine engine which starts with aircraft or ground dc power, then operates on aircraft supplied fuel.

Güç, enerji santrali, Uçak motoru

PRACTICE Prepare aircraft for safe ground maintenance. See Safe Ground Maintenance Procedure, 20-00-00, Maintenance Practices.

Uygulama, fiilen icra etmek, yapmak, çalışmak, uygulamak, tatbik etmek, talim etmek, kendini alıştırmak, tatbikat

- 78 -

PRECAUTION Before using solvents, consult the Materials Safety Data Sheet (MSDS) for special precautions or warnings.

Alınacak tedbir, önlem,

PRELIMINARY The aircraft should be given a preliminary inspection when first removing the inspection covers.

Başlangıç, ilk, ön, ön hazırlık

PREPARE Prepare aircraft for safe ground maintenance.

Hazırlamak, uygun hale getirmek.

Uçağı emniyetli yer bakımı hazırlayınız.

PRESENT If corrosion is present, replace bungee.

Var olmak, mevcut olmak, göstermek , şimdiki

PRESERVATION The envelopes provide preservation, protection, identification and cure date.

Saklama, muhafaza etme, koruma, korunma.

PRESET The system also holds the aircraft to a manual heading or returns it to a preset heading when necessary.

Önceden ayarlamak, Önceden ayarlanmış

PRESSURIZATION Them main entrance door must remain open during the following procedures to avoid accidental pressurization of the aircraft.

Tazyikleme, tazyiklenme, Basınçlandırma, Basınçlı hava verme

PRESSURIZE The detector's sensor tube contains a special core of material and pressurized helium gas.

Tazyiklemek

PREVENT (from) Cable block must be installed to keep cables tight and prevent cables from coming off of pulleys.

Önlemek, engellemek olmasına mani olmak

PREVENTION Humidity need not be controlled beyond the prevention of moisture collecting on the unit.

Önleme, engelleme, önüne geçme

- 79 -

PREVIOUSLY Inspect surface areas which were repaired previously.

Önceden , öncelikle

PRIMARY During normal operation, the steering system has four primary modes of operation.

Ana, ilk, birinci, asıl, önemli,en önemli

PRIMER If assembly was originally protected by primer, prime surface area and apply original finish as required.

Astar, astar boya,

PRINCIPAL This procedure contains the necessary reporting information which is to be used whenever a principal structural element inspection is accomplished.

Ana, baş,başlıca, büyük, asıl, en mühim,

PRINCIPLE The pip-pin quick-release fastener operates on a push-pull principle.

İlke, prensip

PRIOR TO Remove AC and DC electrcal power prior to performing maintenance on AC and DC power receptacles.

Önce, öncesinde

PRIORITY When placing a call, the system will select the first available channel based on the configured priority.

Öncelik.

PROBE This error code will be set when a signal from the shared N1 probe is out of limits.

Hissedici, sonda, araştırma, ölçüm aleti cihazı

PROCEDURE If error occurred during target load, restart procedure.

İşlem, talimat, usül,

PROCEED Corrosion may proceed at a rapid or slow rate. The rate depends on the metal, undergoing attack, the environment,

İlerlemek, yürümek, devam etmek, sürdürmek

- 80 -

PROCESS These tools can carry a static charge, which does not readily discharge during the grounding process.

Süreç, gidiş, seyir , işlem

PROCESSOR The processor unit contains all of the logic circuitry for the system.

İşlemci, işlem yapıcı, işlem birimi

PRODUCE Improper wire stripping can produce a potentially hazardous condition.

Meydana getirmek. Oluşturmak, üretmek,

PRODUCTION To prevent a fire hazard and the production of minor amounts of phosgene gas, do not use a flame-type leak detector.

Ortaya çıkartma, oluşma, ortaya koyma, oluşturma, üretme, üretim, yapim, imal,

PROPER NOTE: Visually inspect retaining ring for proper seating in coupler body.

Tam, uygun, doğru

PROPERLY NOTE: A buildup of lubricant in the O-ring glands may prevent the O-ring from sealing properly.

Uygun, düzgün bir şekilde, gerektiği gibi, hakkıyla

PROPERTY Over inflation of the tire can cause injury to personnel and/or damage to property

Malzeme, mal, parça, cihaz, sahip olunan madde, eşya v.s.

PROPULSION Rotor blades generate the aerodynamic lifting forces as well as the propulsion of the helicopter.

İtme, itki

PROTECT Removing all ac and dc power from the aircraft protects against accidental serious injury.

Önlemek, korumak, kollamak

PROTECTION To prevent injury, use correct personal protection when working with compressed air.

Koruyucu (koruyucu teçhizat), Koruma,

- 81 -

PROVIDE The cabin temperature control system provides the temperature control of the forward and aft cabin zones.

Sağlamak, temin etmek

PROVISION (FOR) Provisions for an optional portable seat may be installed in the aft cargo compartment area.

İhtiyacı karşılamak için, saglama, edinme, vemek, donatmak

PROXIMITY Take a temperature reading in proximity of each sensor (in following order) and record reading at each location.

Yakınlık, etraf, civar

PULLEY A maximum of three broken wires per inch is allowed in any length of cable passing over pulleys and drums.

Makara, kasnak

PULSE High wattage, pulse transmitting avionics equipment shall not be operated in the vicinity of the fueling/defueling operation.

Sinyal, titreşim, vurum darbe, atım, nabız, nabız gibi atan,

PUMP With bath or pump lubrication, check oil level and add oil if needed.

Pompa, pompalamak

PURCHASE This book may be purchased from the following address.

Satın almak

PURGE Purge procedure not required if leak is downstream of system check valves.

Arındırma, temizlik, temizlemek , arıtmak

PURPOSE The purpose of the ac generation system is to provide 115 / 200 Vac, 400 Hz power.

Amaç, gaye, maksat , kararlılık

PUSH Push piston assembly into cylinder until piston head and snubber valve are entirely out of opposite end of cylinder.

İttirmek, bastırmak, basmak,

- 82 -

PUSHROD The control wheel operates a sector actuated pushrod to control flight spoiler functions.

İtme çubukları, itme çekme çubukları, hareket iletme kolu)

QUALITY When in doubt of the sealant quality, the overaged sealant should be compared with the same type of sealant.

Nitelik, iyilik, kalite, vasif; özellik

QUANTITY The compressor rotor turns at high speed and pulls in a large quantity of ambient air through compressor inlet duct.

Miktar,

QUENCH Rapid quenching allows the alloying constituents to be retained in supersaturated solution heat treatment.

Söndürmek, Soğutmak

QUICK Rapid movement of throttle levers can cause engine temperature to change quickly. This will decrease engine life.

Çabucak, çabuk, hızlı bir şekilde.

RADIUS Do not bend cable at less than a 2” radius.

Yarıçap

RAIL When the engine is to be moved by railway or sea, make sure CP30597 is installed.

Demiryolu, ray,

- 83 -

RAISE Using overhead lifting crane, carefully raise lifting sling over engine.

Kaldırmak, yükseltmek, dikmek

RAM The ram air also flows through cold air manifold into cabin and cockpit for emergency cabin ventilation.

Harici, atmosfer

RANGE The weather radar system operates at 9375 MHz (– 40) andhas a range of 300 nm.

Menzil, alan, erim, uzaklık, atış yeri, mesafe,

RAPIDLY Particular attention should be directed toward areas where moisture does not evaporate as rapidly as in other locations more directly exposed to sun and air.

Hızlı, süratli, hızlı bir şekilde,

RATCHET Support mount link and using extension spanner and 1/2 inch drive ratchet wrench, unscrew retaining nut.

Cırcır, dişli çark mandalı, kastanyola, mandal, kilit

RATE RATIO

The oil transfer rate should be slowed to allow the oil time to settle.

Oran, nispet, Derece, çeşit Oran, rasyo

RAY To extend life of Cathode Ray Tube (CRT) displays, it is reccomended to reduce the brightness level of CRTS in the aircraft when not in use.

Işın.

READING Take a temperature reading in proximity of each sensor in following order and record reading at each location.

Değer, okuma, okunan değer, bir aletin gösterdiği sayısal değer

READOUT Thirty seconds after flaps and flap handle reach 0°, flap handle position digital readout on Flight Control synoptic page is not displayed.

Ekranda görüntülenen değer, rakam v.s. Mesajda yazılan değeri okumak

- 84 -

READY Certain types of sealants are available in ready mix kits

Hazır

REAR The aileron position transducers are located at Rear Beam Station (RBS) 409.

Arka, sırt, geri

RECIEVE RECEIVER

The ARINC 429 data bus system has transmitters and receivers connected by shielded twisted wire pairs.

Almak, Alıcı, kabul eden, alan, Ahize, almaç

RECEPTACLE Do not force cabin pressure controller to fit in receptacle on mounting tray. It may result in demage to equipment or bent connector pins.

Elektrik bağlantısı, priz, kap; depo; hazne; havuz; zarf.

RECOMMENDATION All Material Safety Data Sheet recomendations for health and safety precautions shold be followed.

Tavsiye, öğüt, tavsiye mektubu

RECORDER The flight data recorder function is activated by grounding a discrete input pin on the rear connector.

Kayıt, kayıt cihazı, kayıt aygıtı, kaydedici

REDUCE To extend life of Cathode Ray Tube (CRT) displays, it is reccomended to reduce the brightness level of CRTS in the aircraft when not in use.

Düşürmek, azaltmak, indirmek

REDUCER Install O-ring on reducer.

Düşürücü,

REDUCTION The system also employs water separation for humidity reduction.

Azaltmak, düşürmek

- 85 -

REEL Two spring-loaded reels are loaded to hold door in open position without use of any other type of restraining devices.

Makara

REFER (to) Refer to the Structural Repair Manual chapter 51-41-00 for the correct torquing procedures.

Gitmek, bakmak, başvurmak, işaret etmek, göstermek

REFERENCE These classifications may only be determined by reference to the appropriate aircraft SRM.

Referans, örnek, karşılaştırma

REFUELING If automatic refueling has been accomplished since last engine operation, check AUTO REFUEL switch located on systems monitor test panel is OFF.

Dolum

REGARDING Information regarding the engine features necessary for maintenance is contained in the System Description Manual.

Hakkında, ilişkin, hususunda, ile ilgili, yönelik,

REGULATION REGULATOR

Record all maintenance actions in accordance with currentFederal Aviation Regulations.

Kural, Düzenleme, emir,

REJECT If magnet moves laterally along its axis, reject magnetic chip collector.

Reddetmek, kabul etmemek, atmak, bir tarafa atmak

RELATED The flight spoilers are described in detail in the system description for the spoiler system and its related subsystems.

Bağlı, ilgili, ilgisi olan related to; bağlı olarak,

RELATIVE Static electricity can be generated whenever there is relative movement at the interface between two materials or parts,

Kısmi, belli oranda, göre, ilgili, bağlı.

RELAY In order to identify different contacts of one relay or contactor, the terminal numbers may be added.

Röle, Aktarmak, yer değiştirmek

- 86 -

RELEASE The wrist strap must fit firmly against the skin and releasequickly in case of emergency.

Ayrılmak, bırakmak, salıvermek, açmak, açılmak, serbest bırakmak

RELIEF Instructions are provided to relief, dissipate or eliminate static hydraulic pressure in the main hydraulic systems.

Fazla tazyiki atma, Boşaltma rahatlatma, kurtarma, yardım

REMAIN Discard check valve if corrosion remains after cleaning and / or if pitting, nicks, dents or other defects are present which would affect operation of the valve.

Kalmak, arta kalmak, artık, geriye kalan, arta kalan,

REMOTE Connect oil fill remote hose to fitting.

Uzak taraf, iç kısım, ulaşılması zor, uzak,

REMOVE REMOVABLE

Form-in-place gaskets are gaskets formed with sealant between a fixed and removable part.

Çıkarmak, Çıkarılabilir, Taşınabilir , sökülebilir

REPAIR Many major and repetitious repairs may be eliminated by correct and early detection and correction through inspection.

Onarım, tamir, onarmak, tamir etmek,

REPEAT If necessary, repeat the procedure.

Tekrarlamak, yinelemek

REPLACE If leakage is evident, replace complete dust cap.

Değiştirmek,

REPLACEABLE The electric motor is a replaceable component when failure occurs.

Değiştirilebilir

REPLACEMENT Locate near access panels, inspection doors or other accessible areas to permit easy inspection and replacement.

Değiştirme işlemi, değiştirme, yenisi ile değiştirme, yenileme, yerini alan şey, yedek

- 87 -

REPLENISH The magnetic ink should be checked for particle content andcontamination when a fresh quantity is mixed and after each correction or replenishment

Yeniden doldurmak, ikmal etmek

REPORT NOTE: Transponders will not report unless there is 50 knots of airspeed on the aircraft via the pitot / static test set.

Bilgi vermek, sağlamak, iletmek, bildirmek, nakletmek, yazışmak

REPRESENT Error codes contain a unique number that represents a specific problem.

Göstermek, simgelemek, temsil etmek.

REQUIRE The ultrasonic inspection must be done by an approved (NAS410) inspector and requires special equipment

Gerektirmek, istemek , ihtiyaç

REQUIRED Prior training in performing a software load on an aircraft is required.

Gerekli, gerekli olmak, gerekmek ihtiyacı olmak, ihtiyac hissetmek

REQUIREMENT WARNING: The materials in this procedure may have safety, health and environmental requirements related to their use.

Gerktirmek, gerekli tedbir, işlem, özellik, icap, zorunluluk, şart, koşul, istenen şart, gereklilik, ihtiyaç,

RESET If the pop-up indicator has operated and the filter examination is acceptable, reset the pop-up indicator.

Basmak, yeniden kurmak, ayar etmek, eski haline getirmek

RESERVE RESERVED

Main zone 900 is reserved for customizations.

Reserve etmek Ayırmak Rezerv. Ayrılmış

RESIDUAL If the engine has been recently operated, dry motor the engine to remove residual fuel from the engine.

Artan, kalan, artık, kalıntı, tortu

- 88 -

RESIN Phenolic resin is based on phenol and formaldehyde.

Reçine

RESIST RESISTANCE

Under certain conditions, personnel using a grounding strap may need to use a lotion type skin moisture enhancer to provide low resistance conductivity between the wrist and the wrist strap.

Direnmek, dayanmak/ Direnç, mukavemet, dayanma, dayanıklılık

RESOLUTION The brake accumulator display has a range of 0 -4000 psi with a resolution of 10 psi.

Dilim, ölçüm aralığı, hassasiyet, çözünürlük.

RESPECTIVE During normal operations, the IDGs are the primary power generation sources. Each IDG powers its respective main ac bus.

Kendi, kendine ait, ilgili, bağlı, kendine bağlı

RESPECTIVELY The Battery Contactor 1 / 2 connect the output of the left and right main batteries, respectively, to the common battery bus.

Sırasıyla

RESPONSIBILITY

It is the sole responsibility of the user to ensure protection from injury or exposure; safe application of materials; and compliance with any federal, state or local regulations regarding the use of any of the materials specified.

Sorumluluk

RESTORE If the repaired area is not smooth, do the procedure again to restore the aerodynamic profile.

Tekrar oluşturmak, eski haline getirmek, onarmak, yenilemek

RESTRICTOR If a new actuator is to be installed, remove restrictor fitting and union fittings.

Kısıtlayıcı, sınırlandırıcı

RESULT (IN) RESULT

WARNING: Failure to remove alternating current and direct current from Aircraft may result in electric shock.

ile sonuçlanmak, yol açmak, Sonuç

- 89 -

RETAIN Remove screws , retain for reinstallation.

Saklamak, elde tutmak, tutmak , yitirmemek, sahip olmak

RETAINER Attach the retainer ring to the compressor disc assembly with 22 applicable bolts and washers.

Tutucu, bağlayıcı, mesnet bileziği, emniyet bileziği.

RETAINING The retaining ring is made out of two sheet metal plates which are welded together

Tutan, birleştiren, tutucu

RETRACT

The hydraulic power drive unit, located on the torque box in the main landing gear wheel well, actuates the mechanical system that extends and retracts the flaps.

Geri çekmek, içeri çekmek

RETRACTION A single flap handle, located on the pedestal, controls flap extension and retraction.

Toplamak, geri çekmek, içeri almak

RETURN Note direction and number of turns as it may be necessary to return to original position.

Başladığı yere geri dönmek, geri dönmek, geri çevirmek

REVERSE To prevent reverse airflow, check valves are installed in each supply duct prior to the hot and cold air manifolds.

Ters, geri

REVERSION Failure of both the left and right hydraulic systems causes automatic reversion to manual aileron operation.

Geri dönmek, eski haline dönmek.

REVIEW Prior to performing the flap rigging procedure, review paragraph 3.

Gözden geçirmek,

REVISION Any CBs released after publication of this index are active and will be added to this index in the next revision.

Değişiklik, yenileme

RIG Flıght control rigging is prohibited when wind speed is greater than 10 Miles Per Hour.

Ayarlamak, ayar

- 90 -

RIGGING Flight control rigging is prohibited when wind speed is greater than 10 miles per hour.

Ayarlamak, ayar yapmak,

RIGHT Human rights were recognised years ago.

Sağ, Doğru, Hak

RIGID Fluid lines are made of rigid, semi - rigid and flexible tubes, depending on their use.

Sert, sıkı,katı

RING Teflon tape is often used as a thread sealant for oxygen pipe threads and as backing rings for hydraulic seals.

Halka, çember, yüzük, çevrelemek

RINSE Remove turbine bearing from solvent and thoroughly rinse in toluol, isopropyl or butyl alcohol.

Durulamak, bol su ile yıkayarak temizlemek,

RIVET Conventional rivets are not used in composites.

Perçin.

ROD The aileron and rudder trim control head and secondary control rods are located on the pedestal.

Kol, çubuk, değnek

ROLL Roll-type flaring tools are quite popular in aviation maintenance shops because they are entirely self-contained and produce a good flare.

Rulo, silindir, yuvarlanma, döndürme

ROLLER ROLER BEARING

The two rotors are mounted on a common shaft supported with a roller bearing at the drive end and a ball bearing at the antidrive end.

Makara, silindir, ufak tekerlek roller bearing: makaralı yatak.

ROTARY If pin A is energized, the rotary actuator shaft rotates clockwise as viewed from the output shaft end.

Ekseni etrafında dönen, dönebilen

- 91 -

ROTATE The motor will continue to rotate but at a lower power level to the operational characteristics of this type of clutch.

Dönmek,

ROTATION Turn rotating group to view each compressor blade using the engine rotation procedure.

Döndürme, çevirme, dönme, dönüş, devir, değişim,

ROTOR The rotor assembly contains the permanent magnet generator rotor and exciter armature.

Rotor

ROUTE It is preferred, but not required, to route wire above rather than below liquid carrying lines to prevent contamination or saturation of the wiring in the event of leakage.

Dolaştırmak, yönlendirmek, yol, taraf, yön, rota,

RUB Do not rub aircraft surface when removing volcanic ash.

Ovalamak.

RUBBER Corrosion inhibiting compounds can cause silicone rubber to swell.

Lastik, kauçuk

SAME The procedure is the same as for the free-hand rivet drill-out technique.

Aynı

SAMPLE Ship hydraulic fluid sample(s) to vendor or laboratory for analysis.

Numune, örnek.

SATELLITE Iridium Satellite transceiver relays information to ground stations for transfer to the terrestrial phone system.

Uydu,

SCALE Altitude information appears to the right of the vertical deviation scale.

Ölçek, taksimat, bölüntü, ölçü, çap, cetvel, derece, kademe,

- 92 -

SCAVENGE The lube pump assembly is a LRU that supplies lubrication and scavenge functions for generator.

Temizleme.

SCHEDULED You can accept the corrosion and do the repair at the next scheduled maintenance.

Planlı, Belirlenmiş, Programlı, planı önceden yapılmış.

SCORE Inspect outer surface of engine lower cowl door for scores and scratches.

Kertik, çentik

SCRAPER Insert a nonmarking scraper between mirror assembly and windshield side post and carefully pry bracket loose.

Kazıyıcı, sıyırıcı.

SCRATCH Inspect outer surface of engine upper cowl door for scores and scratches.

Çizik, bir yüzey üzerindeki çizgiler, oyuntular, kazıntılar.

SCREEN During movement of the probe look at the structure noise signal on the screen of the ultrasonic flaw detector.

Ekran, elek, süzgeç, örtü, perde, bölme, ayırıcı, sinema ekranı,

SCROLL You can scroll through the BITE indications on the alphanumeric display and identify the defective LRU ( Line Replecable Unit ).

Gezinmek, dolaşmak, ekranda görüntü kaydırmak, liste, cetvel,

SEAL Remove and discard seals and O-rings.

Conta, macun

SEALANT

If sealant has been previously applied, this step may be omitted.

Macun, conta,

SEARCH (FOR) A detailed inspection searches for evidence of irregularity using adequate lighting and where necessary, inspection aids such as mirrors, hand lens, etc.

Bulmaya çalışmak, Bulmak için aramak, araştırmak,

- 93 -

SEAT Ensure controller is seated firmly in mounting tray.

Oturmak, oturtmak, yerleşmek, Koltuk, oturacak yer, yuva

SECOND SECONDARY

The ram air inlet and exhaust system provides cooling airflow across the primary and secondary heat exchangers.

İkinci, ikinci derecede olan, ikinci gelen, ikincil

SECTION The repair section of the aircraft manual will indicate the extent and location of damage

Bölüm

SECURE Secure exhaust duct assembly to rack with screws and washers.

Sabitlemek, emniyete almak, sıkılaştırmak

SECURITY Before you start the test, check all connections for security to prevent the possibility of local leaks.

Sağlamlık, sıkılık, güvenlik, emniyet, koruma, güvence,

SEGMENT It may be necessary to loosen or remove both duct segments above bleed air augmentation valve in order to remove valve assembly.

Kısım, parça. Segman. Kısımlara ayırmak, bölmek.

SELECT Verify or select the following switch configuration on BLEED AIR panel.

Seçmek,

SELECTION For usual engine starts on the ground the EEC makes an automatic selection of one channel and one igniter plug.

Seçme,Seçim

SELECTOR Remove screw from selector handle.

Seçici, Yön tayin edici, ayırıcı İdare kolu

- 94 -

SEMI The windshield heating system is designed to accomplish semi-automatic anti-icing of the cockpit windows.

Yarı.

SENSE Both engine fire detection loops sense a fire or overheat condition.

Duyu, duyum, anlam, akıl, genel düşünce, yön, hissetmek

SENSITIVE The relief valve is a spring loaded valve sensitive to pump delivery pressure.

Duyarlı, hassas, narin

SENSITIVITY To set sensitivity level, push MKR SENS line select key.

Hassasiyet.

SENSOR When the temperature sensor senses an air temperature of 160°F or greater, an amber message will be displayed.

Hissedici

SEPARATE The air conditioning pack will need to be separated into two pieces in order to fit through aircraft tail compartment door.

Ayrılma, dağılma, kademelenme

SEQUENCE When performing full load with all CDs, loading sequence is as follows:

Sıra, silsile, takip, sıralı, zincirleme.

SERIOUS Faılure to ensure all personnel and equipment are clear of flight control surfaces before operating flight controls may result in serious injury or death.

Ciddi,

SERVICE/SERVICEABLE Maintain tools in good serviceable condition. Using wrong equipment or worn tools may be dangerous.

Hizmet, servis Kullanılılabilir, faal, iyi durumda, işe yarar, elverişli,

- 95 -

SET Set flow at 22.5 gpm and 3000 psi.

Ayarlamak, istenen konuma getirmek, kurmak, oluşturmak / Set, takım

SETTING Turn rheostat to comfortable temperature setting.

Ayarlama , ayar yapmak

SEVERAL Click START LOAD and verify the following message is displayed after several minutes.

Birkaç, çeşitli, muhtelif, başka münferit, tek, severally birer birer,

SEVERE Failure to depressurize air conditioning and allow components to cool prior to performing maintenance could result in severe burns to personel.

Sert, haşin, katı

SHAFT The powerplant system section consists of an impeller and a flow turbine wheel, both mounted on a common shaft.

Mil, kol, sap, araba oku,

SHAKE The stick shaker becomes fully functional when the aircraft becomes airborne.

Titretmek. sarsmak, sallamak,

SHAPE Files exist in different shapes: as flat, triangular, square, half-round and round files.

Şekil, biçim

SHEAR To obtain good shear resistance, the fibres must also be stacked along the ± 45° orientations.

Biçmek, kırpmak, kesmek

SHEET The life of a Critical Part is recorded in the module log sheet.

Defter, kağıt yaprağı, tabaka , levha, sac

SHELF SHELF LIFE

The shelf life of a synthetic rubber part is calculated from its cure date.

Raf, Raf ömrü

- 96 -

SHIELD Visually inspect igniter leads for broken, frayed or other damage to shielding.

Koruyucu sargı, örtü, kalkan, siper, koruyucu, korumak,

SHIM Remove bolts, washers and shims.

İnce levha, pul, yassı çubuk,

SHOW The CLOSE / OPEN indicator shows valve moving toward OPEN position.

Göstermek, görünüş

SHRINK Shrink the sleeving over the chafed area beginning at the connector continuing toward the cable using heat gun.

Büzüştürmek, büzdürmek.

SHUTDOWN Make sure that the engine has been shutdown for not less than 5 minutes.

Susturmak, durdurmak, kapatmak,

SHUTOFF Baggage compartment shutoff valve reset switch is located on the smoke evacuation panel.

Durdurmak; kapamak

SHUTTLE Nitrogen is also released in to the shuttle valve on each sidebrace actuator, door actuators and uplock actuators.

Mekik. Araç

SIDE The glue is spread on one side of the joint using a thin wooden spatula.

Yan, taraf, kenar

SIGHT GLASS If the hydraulic test stand has been modified to incorporate a sight glass in the suction hose, then the another hose assembly with sight glass is not necessary.

Kontrol camı, inceleme camı,

- 97 -

SIGN SIGNAL

If rig pins are tight or show signs of binding, it may be necessary to adjust force sensors.

İşaret, belirti İşaret, sinyal

SIGNIFICANT The numbers also turn amber when a significant oil pressure difference exists between the engines.

Önemli, anlamlı, değerli, ciddi,büyük,

SIGNS Remove covers and inspect top of cells for signs of seepage.

Emare, ibare, işaret, belirti , iz

SIMPLE Most quick release fasteners utilise a simple method to indicate when they are in a locked or unlocked position.

Basit, sade

SIMILAR Pitting on aluminum alloys is first noticeable as a white or gray powdery deposit, similar to dust.

Benzer, aynı türden

SIMULTANEOUSLY If both wing tanks are to be defueled simultaneously, provide sufficient equipment.

Aynı anda, aynı zamanda, birlikte, eş zamanlı

SINCE Areas where dissimilar metals are in contact must be closely inspected, since an electric current is generated andflows from one metal to the other.

Diği için, den dolayı

SITUATION It is the ultimate responsibility of the technician to ensure the aircraft is configured for safe ground maintenance as the situation requires.

Durum, vaziyet

SIZE If error message displayed, file size may be invalid or content may be invalid due to deviation from expected format.

Boyut, miktar

- 98 -

SKID The auxiliary hydraulic fluid flows through one of the antiskid valves for each landing gear.

Kaymak, yana kaymak,

SKIN The wrist strap must fit firmly against the skin and release quickly in case of emergency.

Deri, cilt, kabuk, dış kaplama

SLACK Ensure cables for antenna and electrical connector have appropriate amount of slack.

Gevşeklik, boşluk

SLEEVE Remove couplings from tube assemblies. Slide sleeves onto tube assembly.

Bilezik, rondela, duy, içi boş mil, gömlek, fiş gövdesi, kablo kılıfı.

SLIDE Slide beacon into right bracket.

Kaydırmak, sürmek, sürgü, Kızak, kayma, kayış.

SLIGHTLY Left flight spoilers may deploy slightly when control wheel is rotated clockwise.

Hafifçe, birazcık.

SLING Operate the crane to tighten the straps of the sling and to hold the weight of the thrust reverser.

Askı, iple asmak, halatla kaldırmak, asmak,

SLIP Cut and remove cable ties and slip both sleeves toward silencer and lift silencer free.

Kaydırmak, kaymak, sıvışmak, yerinden çıkmak,

SLOPE The aural alerts are two different sounds related to the position of the aircraft below the glide slope.

Açı, eğim.

- 99 -

SLOT Position valve (1) and bracket (6) as high in tank as slot adjustment will allow.

Yarık, yiv, oluk.

SMOKE The fire and smoke detection system is made up of a smoke detector and controller located in the baggage compartment.

Duman, sis

SMOOTH Make bonding or grounding connections to clean, smooth surfaces.

Düzgün, Pürüzsüz.

SNUBBER The lower door has a gas spring snubber installed on the forward side.

Amortisör yayı, valfi, kelepçesi dikmesi,

SLOT Position valve (1) and bracket (6) as high in tank as slot adjustment will allow.

Yarık, yiv, oluk.

SMOKE The fire and smoke detection system is made up of a smoke detector and controller located in the baggage compartment.

Duman, sis

SMOOTH Make bonding or grounding connections to clean, smooth surfaces.

Düzgün, Pürüzsüz.

SNUBBER The lower door has a gas spring snubber installed on the forward side.

Amortisör yayı, valfi, kelepçesi dikmesi,

SO SO THAT

Both turrets are synchronised so that they rotate together.

Bu yüzden, Böylece

SOLDER SOLDERING

Instead of soldering, in most cases crimping technology is used.

Lehim, Lehimleme

- 100 -

SOLENOID Movement of solenoid ports allows fully regulated pressure to actuator closing chamber driving butterfly plate to fully closed position.

Manyetik bobin, solenoid, sarmal bobin

SOLID When prepolymer and the accelerator thoroughly mixed, the catalyst cures the prepolymer to a rubbery solid.

Sertlik, kıvam, katı, yoğun, içi dolu, üç boyutlu, sağlam, som,

SOLUTION Alodine solution should have an amber color. If solution is coffee colored, it has become contaminated.

Çözelti, karışım, eriyik, solüsyon.

SOUND Do not rely on fuel boost pump sound to determine cavitation.

Ses, seda, avaz

SOURCE If oil leakage is found, run APU test to find source of leak.

Kaynak, geldiği yer

SPACE Determine if space is available in the left or right fuel tank to accept the quantity of fuel to be transferred.

Boş alan, boş yer, boşluk, alan

SPACER With duct in place, install screws, washers and spacers attaching duct to brackets.

Ara burcu, ara yüksüğü, burca benzeyen özel pul, ara bileziği,

SPAR At the joint of the wing spar box with the wing rib, inspect the following components for distortion, cracks, pulled or torn fasteners.

Seren, direk

SPARK The number of cables required for a system corresponds to the number of spark plugs.

Kıvılcım, ateşleme

SPECIAL Special tools and test equipment.

Özel

- 101 -

SPECIFY SPECIFIED SPECIFIC

Many of the materials specified here have significant occupational safety, health or environmental requirements.

Belirlemek,Belirtilen, Bahsedilen, Belirli

SPEED Bleed air may be used immediately after APU operating speed exceeds 99% for at least 2 seconds.

Hız, Sürat

SPILL Hydraulic fluid can damage paints, rubber, and plastic materials. Care must be taken to prevent spillage from remaining on surfaces or damage may result.

Dökmek, dökülmek

SPLICE A standard cable splice is used to connect the launch cable to the cable under test set.

Ekleyici, ek, eklemek, bağlantı yeri, uçları birbirine bağlamak.

SPLINE Carefully insert transducer shaft into spline opening on housing assembly.

Kama, dil, şaft , mil

SPLIT Adjust both engines identically to prevent splits in engine acceleration / deceleration and flight idle rpm.

Uyumusuzluk, farklılık, ayrışma, ayrılma, bölünme

SPLITTER The cockpit distribution duct extends left and right from the supply duct splitter under the aft cockpit.

Dağıtım, ayırma, bölme, dağıtıcı. ayırıcı, çoğaltıcı

SPRING, SPRING-LOADED

This regulator is a spring-loaded open, pneumatically operated, pressure regulating and relief valve.

Germek/Yay Yay yüklü,

SQUARE Monitor cabin pressure to ensure pressure does not exceed 9.8 pounds per square inch.

Kare (alan biriminde kulanılır).

STABILIZE Select APU BLEED AIR switch ON and permit bleed air pressure to stabilize for 1 minute before start of leak checks.

Dengesini, durulmasını sağlamak, dengelemek,

- 102 -

STABILIZER The horizontal stabilizer pivots to change angle of incidence as flaps are extended or retracted.

Dengeleyci, stabilizer

STAGE Visually examine the LP stage 2 turbine blades for damage.

Kademe, basamak, safha, durum, derece, mertebe, toplamak, hazırlamak.

STALL Compressor stall can occur when the airflow through a compressor is low in relation to its rotational speed.

Durmak,

STANDBY The standby rudder system, which utilizes the auxiliary hydraulic system, can be used to supply hydraulic power to the rudder hydraulic actuator.

Yedek, hazır, cihazın çalışma, hazırlık safhası, hazırda beklemek,

STATE Depending upon state of battery charge, amps could be 35 – 5 maximum while charging.

Durum,hal, mevki, İfade etmek, açıklamak

STATIC The bungee is to be extended mechanically, but must return to a static state without assistance.

Durağan, sabit, hareketsiz, Static state: eski haline dönmek

STATIONARY Install the removable part to stationary part.

Sabit, durağan.

STATOR The combustion gasses continue through second stage stator and then hit and turn blades of second stage turbine rotor.

Sabit, dönmeyen.

STATUS The color of the REV message provides the status of the system.

Durum, hal, mevki, statü

- 103 -

STEADY The aircraft must be stationary or held at a steady attitude and velocity during this test.

Sabit, düzenli, değişmeyen.

STEEL If corrosion deposits are evident, use a firm bristled or stainless steel brush to remove deposits.

Çelik, sertleştirmek, katılaştırmak

STEM Lubricate pedestal landing gear control valve stem (area routed through fitting) with MIL-S-8660.

Kol, sap, kök , dip kısım,

STEP When performing the following steps, allow 3 minutes for the temperature to stabilize.

Basamak, çıkıntı , işlem sırası

STERILIZER Install water sterilizer fillter to sterilizer.

Arıtma cihazı, temizleyici, arındırıcı, arıtıcı,

STICK Removal and installation procedures for left and right stick shaker is similar. Only left procedure is given.

Lövye

STILL After one engine is running, APU bleed air can still be used to start the second engine.

Hala, Buna rağmen, Sabit, haraketsiz , Kıpırdamadan.

STORAGE Put the removed blade in to an applicable storage box.

Kutu, sandık, kutulama, saklama kabı, depolama

STORE Disconnect electrical connector, install protective device and store safely.

Yüklemek; kaydetmek , muhafaza etmek , depolamak

- 104 -

STRAIGHT

Pull controller straight out of mounting tray until electrical connector on unit is free from mounting tray.

Dümdüz, düz bir şekilde, Doğruca, dosdoğru, düz.

STRAP Each person handling ESD sensitive components and equipment must wear a grounding strap to dissipate bodily electrostatic charges.

Bileklik, kayış, şerit, bant, kayışla bağlamak

STRENGTH The rivet pitch of a joint will depend on the type and structural strength of the joint.

Güç, kuvvet, dayanıklılık, direnç

STRESS Cold working or straining, quenching in heat treatment, grinding or welding may produce internal stresses on metals.

Baskı, tazyik, gayret,

STRINGER Remove nut, washer and lock washer securing jumper cable to ground stud on wing stringer.

Kiriş.

STRIP Check pH of surfaces using standard laboratory pH test strips and continue rinsing until surfaces are within a pH range of 6.0 - 8.0.

Şerit, bant. sıyırmak, soymak

STROKE The forward stroke is carried out with pressure, the return stroke without pressure.

Darbe, çarpma, okşama, inme, felç

STRUCTURAL Thick structural sections are subject to corrosive attack because of possible variations in their composition.

Yapısal,

STRUCTURE Inspect outer structure of heat exchanger for dents, cracks or discoloration.

Yüzey, gövde, yapı, cephe, iskelet, kuruluş, bir kuvvetin yapısı.

- 105 -

STRUT Ensure rear support struts are held in position when disengaged from the rear adapter assemblies.

Dikme, iniş takım dikmesi, destek, kolu, destek elemanı, payanda

STUD A maximum of four wire terminals may be installed on an individual grounding stud.

Sabit tespit cıvatası, tespit tapası, saplama, destek, vida

SUB In addition to the major buses, there are eight sub-buses.

Alt., ikincil

SUBJECT TO Thick structural sections are subject to corrosive attack because of possible variations in their composition,

Maruz kalmak,

SUBMENU Comply with the following to access configuration submenu.

Alt Menü

SUBSEQUENT The subsequent increase in temperature causes the gases to expand and accelerate rearwards.

Sonradan ortaya çıkan, sonradan gelen, sonraki, sonuç,

SUBSYSTEM The engine will operate in association with appropriate aircraft subsystems.

Tali sistem, alt sistem

SUCH SUCH AS

A detailed inspection searches for evidence of irregularity using adequate lighting and where necessary, inspection aids such as mirrors, hand lens, etc.

Böyle, öyle. Gibi

SUCTION Disconnect hydraulic test stand pressure and suction lines.

Emiş, emme, massetme, havasını alma, vakum, alt basınç.

- 106 -

SUFFICIENT Check that ELT antenna is radiating sufficient power as follows.

Yeterli,

SUITABLE The use of corrosion inhibiting compounds on control cables is not considered a suitable substitute for cleaning and corrosion protective procedures in maintenance manual.

Uygun, yerinde, elverişli

SUMMARY Operational summary:

Özet, Kısa

SUMP A water sump, drain port and temperature sensing port are located on the outlet duct assembly.

Toplama/Atık haznesi. Depo, hazne

SUPPLEMENTAL The aircraft includes supplemental heating beneath the carpet.

Ek, ilave

SUPPLY NOTE: Compressed air source shall supply clean, oil free, silicone free, moisture free, filtered air.

Sağlamak , vermek, temin etmek, tedarik etmek, ikmal

SUPPORT Carefully and slowly adjust overhead lifting crane until full weight of engine is supported by engine transit stand.

Binmek, ağırlığını çekmek, taşımak, desteklemek, tutmak,Destek, dayanak

SURFACE Ensure all personnel and equipment are clear of flight control surfaces before operating the system.

Yüzey, satıh.

SURGE When engine speed stabilizes at maximum Engine Pressure Ratio in less than 1 second, move power lever back to MIN IDLE position. Ensure engine does not surge.

Aniden artış yapmak, artmak, dalgalanmak, ani kabarma.

- 107 -

SURROUNDING Examine the line fittings and the surrounding area for evidence of hydraulic fluid.

Çevreleyen, çevredeki, etraftaki, civardaki,

SWING Right door will swing open.

Salınmak, sallanmak, sallamak, salınım, aniden geriye dönmek,

SWIVEL Visually inspect all hydraulic lines, fittings and swivels on affected main landing gear strut.

Döner bağlantı, mil veya dingil üzerinde dönen, döndürmek,

SYMBOL All ESD sensitive components and equipment should be marked appropriately with an ESD symbol

İşaret, rumuz, alamet, sembol.

SYNOPTIC Verify AC Power synoptic page is displayed with the following information:

Sinoptik

TAG Pull tag and install safety clip on the following Circuit Breaker (CB):

İkaz bayrağı, etiketlemek, kimlik belirten işaret, etiket

TAIL Inspect length of cables in tail compartment for broken wires, corrosion and areas of wear or damage.

Kuyruk,

TAP Periodic rinsing with tap water should be accomplished as necessary to prevent deterioration of aircraft surfaces.

Musluk

- 108 -

TAPER Taper the edge of the disc to allow it to fit into the joint seam.

Pahlamak, Uca dogru inceltmek, sivriltmek, koniklik vermek

TARGET In the weather radar mode, the Central Display System shows weather radar data in different video levels to reflect the specific target intensity of the weather conditions.

Hedef, amaç

TASK Hydraulic power is not required unless this task is done in conjunction with Aileron HOPS - Operational Check.

Görev, iş kartı

TEE Remove fuel hose assembly from tee.

T bağlantısı, T şeklinde bağlantı,dirsek.

TEMPORARY If temporary fasteners were installed in the outer pane, make sure they are removed.

Geçici, deneme amaçlı,

TENSION TENSILE

Safety cable shall be applied in such a manner that cable is put in tension when parts tend to loosen.

Gerginleşmek, gerilmek, gerginlik, Gerilme

TERMINAL Remove nuts, flat washers and lock washers securing wires to battery charger terminals, then remove wires.

Uç, bağlantı, kutup, uçta veya sonda olan veya bunlara ait

TERRAIN The tilt control on the weather radar controller is turned downuntil the satisfactory amount of terrain is displayed.

Arazi, alan, saha

TERTIARY İt is necessary that tertiary lock can always operate.

Üçüncü

- 109 -

TESTING The FCU protects systems by doing operational status testing with Built-In Test (BIT) and functional fault monitoring.

Test yapmak,

THERMAL Normally open thermal switches are installed near the bleed air ducting that passes through the pylons.

Isı, termik, hararete ait, sıcağa ait, sıcakla ilgili

THEREFORE/THUS A double flare is smoother and more concentric than a single flare and, therefore, provides a better seal.

Bundan dolayı, Bu nedenle

THICKNESS Apply Type IV and VII compounds at a wet film thickness of 2 mils for a final dry film thickness of 1 mil.

Kalınlık

THIN To prevent damage to O - rings during assembly, apply a thin coat of oil.

İnce, inceltmek, zayıf

THOROUGHLY Thoroughly wash contaminated clothing and shoes before reuse.

Baştan aşağı, tamamen, iyice

THREAD Closely inspect all threaded surfaces for evidence of over torquing. Replace parts showing evidence of over torquing.

Civata dişi, vida, yiv, diş. İp, sicim

THREADED Do not apply grease to the threaded area of the bolt.

Dişli, Vida dişi açılmış

THRESHOLD As vacuum in the control chamber is evacuated beyond a threshold value, the control chamber acts upon a diaphragm that pulls open a normally closed poppet valve.

Başlangıç, kapı eşiği, eşik, girecek yer, başlangıç,

- 110 -

THROUGH Copilot cockpit lighting is provided through four circuit breakers on the right main 28 Vdc bus:

Üzerinden, tarafından, içinden, içinden geçmek Vasıtasıyla, yoluyla

THROUGHOUT This controls conditioned air throughout the cabin for maximum comfort.

Her yer, her taraf, tamamen, baştan başa, tüm, boyunca

THROW Move elevators full up. Record throws.

Hareket mesafesi, atma, sapma mesafesi, sapma , atma , fırlatma

THRUST They develop thrust which results in heavy movement of the air behind the engine outlet.

İtmek, sokmak, saplamak İtki, itiş, itme

THUS Under normal conditions, APU bleed air pressure is greater than the operating engine bleed air pressure, thus APU bleed air would be used to assist in the second engine start.

bu şekilde, böyle, böylece, bu sebepten dolayı

TIGHT Torque swing bolt nuts to 109 foot-pounds (147.78 Nm) and tighten lock nuts.

Sıkmak.

TIGHTEN Install bolt, washers and nut. Tighten and safety with cotter pin.

Sıkmak,

TILT After initial test flight, it may be necessary to adjust tilt angle of control wheels.

Eğim, meyil, yerine oturtmak,

TIMER When the APU air inlet door has been fully closed, a 5 minute timer is activated.

Zamanlayıcı.

- 111 -

TIP Typical airframe components made of bent solid wood include wing-tip bows, rib cap strips and fuselage stringers.

Uç, nokta

TIRE Measure and record minimum distance between tire and door with door in the open free position.

Lastik, tekerlek.

TOGETHER Fasten parts together and verify squeeze out is present along entire edge of parts joined.

Birbiri, birlikte, biraraya, beraber.

TOLERANCE Correct any condition that is out of tolerance.

Kabul edilebilir değer, fark, boşluk, kabul edilebilir hata,

TOOTH/TEETH The depth of a tooth space below, or inside of, the pitch circle is dedendum.

Diş

TOP A top coat provides a coloured surface.

Üst, zirve

TOTAL The total height of a tooth or the total depth of a tooth space.

Toplam, tutar, tüm, bütün

TOW TOW BAR TOW VEHICLE

The aircraft can be towed forward or be pushed backward on hard surfaces using a Gulfstream approved towbar and towing vehicle or towing vehicle not requiring a towbar.

Çekmek; yedekte çekmek, Çeki Demiri Uçak Çeker

TOWARD Operator should position themselves to spray in direction where mist will not drift towards him.

O yöne doğru, -e doğru.

TRACK Time to be tracked from the earliest compliance date of the above listed codes.

Takip etmek , izlemek , ray, klavuz

- 112 -

TRAILING TRAILING EDGE

Adjust borescope insertion tube to examine leading edges and trailing edges of compressor blades.

Arka, sırt, geri, Arka kısım, arka kenar-yüzey

TRAIN TRAINING

For training purposes only

Eğitmek, eğitim yapmak, eğitim

TRANSFER Transfer 10 ml of distilled water into a clean vial.

Aktarım, aktarmak, geçirmek, iletmek, geçiş,

TRANSITION If engine speed accidentally stabilized in keep-out zone (66% - 80% N1) or transition through keep-out zone took longer than 10 seconds, perform the following:

Geçiş, intikal,

TRANSMISSION Secure transmission ducts to blowers with clamps.

Geçirme, nakil, intikal, aktarma, gönderme, iletme, taşıma

TRANSMIT Identical data is transmitted at the same time on both buses.

Göndermek, geçirmek, iletmek , yayımlanmak

TRANSMITTER Connect the electrical connector to the oil quantity transmitter of the accessory gearbox oil tank.

Verici, iletici

TRANSPONDER When the antenna is in position, the SDU receives a pilot tone from the satellite transponder.

Verici.

TRAVEL Rotate control wheel fully in both directions and check aileron travel.

Hareket mesafesi. Seyahat hareket

- 113 -

TRAY Install Operational Software CD into laptop computer CD-ROM tray.

Tabla, tepsi,

TREAT TREATMENT

Heat treatment is a series of operations involving the heating and cooling of steel in the solid state.

Davranmak, muamele etmek, tedavi tamir etmek, işlemden geçirmek

TRIGGER Using SCROLL knob, place cursor on WX and press trigger to select.

Tetikleyici , tetiklemek , tetik, mandal

TRIP The test does not check the alarm switch temperature trip points.

Çalışma,geçi

TRUE To obtain a true reading, the applicable hydraulic system must be pressurized to a minimum of 700 psi.

Gerçek, doğru

TRUNNION The thrust trunnion is a matched assembly made of five parts.

Muylu, mil,

TUBE Disconnect air supply tube (which is) attached to jet pump.

Boru, duct'a göre daha ince boru

TUNE The VHF voice communications system is tuned through the radio tuning page on the MCDU.

Ayarlamak.

TUNING The Very High Frequency Omnidirectional Range system is tuned through the radio tuning page on the MCDU.

Ayar, Ayarlamak (frekans vb).

TURN The torque motor flapper will turn from the supply line to thevent with a variable current input.

Dönmek, döndürmek, çevirmek, devir,

- 114 -

TURNBUCKLE Remove safety wire from forward and aft 5/32 inch diameter cable turnbuckles.

Tandör, gergi tokası

TWIST Single wire may be used for parts in electrical systems where accessibility or frequent removal make double twist method impractical.

Kıvırmak, bükmek, sarmak, burmak, birbirine dolamak, örgü yapmak, sarmak,

TYPE The basic characteristic of a truss type structure is that its struts carry only compressive loads.

Tip, tür, örnek

TYPICAL Typical materials used for this purpose are epoxy, polyurethane, silicone rubber, acrylic, varnish, etc.

Tipik, özgün, karakteristik

UNIT Many other units of length measurement have been used in various countries.

Birim, ünite, öğe,

UNION CAUTION: Union must be held firmly in place when disconnecting tube.

Rekor,

UNIVERSAL A control column head universal joint connects the control column to the torque tube through a yoke connection.

Çok yönlü, her yöne dönebilen, genel, yaygın, küresel,

UNLESS The air shut off valve remains closed unless any of the following occurs.

-madıkça , -mezse , medikçe

- 115 -

UNSATISFACTORY When performing the flap system check on airplanes with fuel in the fuel tanks, the cable tension readings may be unsatisfactory.

Uygun olmamak, hoşnut olmamak, memnun olmamak, tatmin etmeyen, yetersiz,

UNTIL, TILL The test piece is loaded until it breaks.

-e kadar,

UNWANTED Loosen the bleed-screw as necessary to release unwanted air.

İstenilmeyen, arzu edilmeyen

UPDATE This section will be updated periodically to share our experiences on the development of inspection techniques and preventative measures.

Güncellemek, güncelleştirme

USE USED

Use rivets of same type which are installed in the area

Kullanmak, kullanım. Kullanılan, kullanılmış.

USER During course of data loading, user may encounter problems at various stages of software loading process.

Kullanıcı, kullanan

USUALLY Cockpit temperature control sensors are usually located on lower cockpit center pedestal.

Genellikle.

VACUUM Remove all unwanted material from the repair area with a vacuum cleaner.

Boşluk, vakum

VALID If the Flight Management System (FMS) data is not valid, the Cabin Pressurization Controller uses an auto schedule for control of the cabin altitude and rate.

Geçerli, uygun,

- 116 -

VALUE Follow torque values posted on power distribution box tray for connector and terminal block.

Değer, kıymet, itibar, önem, ehemmiyet, gerçek değer,

VANE Perform this procedure when oil staining or wetness has been observed in the fan case or on the fan outlet guide vanes.

Kanatçık, küçük pervane. Pale

VAPOR Skydrol type IV phosphate ester haydraulic fluid is combustible and can be a health hazard. Inhalation of vapor and contact with skin and eyes should be avoided.

Buhar

VARIABLE The torque motor flapper will turn from the supply line to the vent with a variable current input.

Değişken, sabit olmayan , ayarlanabilir

VARIOUS The system consists of normally open thermal switches mounted at various locations throughout the aircraft.

Çeşitli, değişik, farklı

VARY Location of temperature control sensors may vary depending on aircraft configuration.

Değişiklik göstermek, değişmek, çeşitli, değişik.

VELOCITY Pressure washing of aircraft is not recommended due to the high velocity water and cleaning agents can force dirt and moisture into the system components.

Hız, sürat

VENDOR Listed below are documents for vendor preservation and storage instructions:

Üretici firma.

VENT Pressure relief valve provides positive differential pressurerelief by venting cabin air through the pressure vent port.

Dışarı atmak, boşaltmak, salmak, delik, çıkış, atılma,

VENTILATION Tank ventilation provides sufficient venting while the aircraft is on the ground and during flight.

Hava dolaşımı, Havalandırma.

- 117 -

VERIFY If you find cracks or unusual marks, use inspection lamp or suitable light source to verify the cracks.

Temin etmek, Doğruluğunu kanıtlamak, doğrulamak

VERTICAL The algorithms determine the necessary vertical movement to prevent a midair or near midair collision.

Dikey, düşey,

VIA Power for the 60 Hz bus can be obtained from an external power source via an external 60 Hz power receptacle.

Vasıtasıyla, aracılığıyla, yolu ile

VIBRATION Increase in engine vibration levels may develop in icing.

Titreşim, sarsıntı

VIEW

Görüş

VISIBLE No damage is visible on entire length of harness spiral wrap.

Görünür, görülebilir

VISION The enhanced vision system alignment will be required after completion of software loading.

Görme , görme gücü , görüş

VISUAL Visually inspect all shock absorber attaching pins, bushings and bolts for wear. Replace as necessary.

Gözle, görsel olarak,

VISUALLY Visually Examine the Stage 2 LP turbine blades.

Göz ile, görerek.

VOICE These subsystems include components which supply voice and data communications.

Ses, düşünce, dile getirmek, söylemek, seslendirmek

- 118 -

VOID This procedure will void warranty on any signal conditioner still under warranty.

Yasal olarak geçersiz bırakmak.

VOLUME Due to the large volume of the fuel tanks, it is not recommended that the aircraft be weighed with full fuel tanks.

Hacim, miktar

VORTEX Vortex generators in this procedure are located forward of the safety valve on right side of aircraft at FS 145.

Hava akımı, girdap

WALL Check clearance between inboard pedals and pedestal walls.

Duvar.

WARNING WARNING: Do not touch windshield or windows with windshield heat ON.

İkaz,ihbar.

WASTE Clean toilets and waste water systems by flushing and draining.

Atık, artık, artık madde, boşa harcamak, ziyan etmek

WAVE Ultrasonic testing uses a high frequency sound wave as a means of detecting flaws in a part.

Dalga

WAY The four basic ways to control static buildup used in Electro Static Discharge control.

Yöntem, yol.

WEAR If wear and erosion of the surface layer lets you see the base metal, the surface layer must be repaired.

Yıpranma, yorma

- 119 -

WEATHER The corrosion preventive compound ,Grade 1, is used for protection of metals when exposed to outdoor weather conditions.

Hava, hava durumu

WEDGE If aircraft is on jacks, WOW wedge is the only authorized tool to place aircraft in ground configuration.

Kama, takım, takoz, araya sıkıştırmak,

WEIGHT Carefully and slowly adjust overhead lifting crane until full weight of engine is supported by engine transit stand.

Ağırlık, yük,

WELDING Therefore most arc welding is shielded from the air.

Kaynak, kaynama

WET A spray nozzle to surface distance of no more than 12 inches is required for wet application.

Yaş , ıslak , nemli

WHEEL A pulley is a wheel, either fixed to a turning axle or carried freely on a stationary one.

Tekerlek, dümen

WIDTH The stands shall be of sufficient height and width to permit working access to the stabilizer from tip to tip.

Genişlik, en

WIND Gusty winds cause large fluctuations of N1 which makes interpretation of test results very difficult.

Rüzgar, yel, sarmak, dolamak, dolanmak

WINDSHIELD The windshield heat switch provides manual control ofwindow heat.

Ön cam,

WINGLET There are vortex generators mounted on the top surface of the outer wing and winglet.

Kanatcık, Kanat ucu çıkıntısı, kanat boynuzu

- 120 -

WIRE WIRING

Tel, Kablo donanımı

WITHIN After a period of1-2 hours, the shock absorber pressure willstabilize down to within required limits.

İçerisinde, içinde

WITNESS Ensure that threads are visible through witness holes in pushrods.

Bakma, görme, şahit olma, tanıklık etmek, şahit olmak.

WOOD Wood screws are employed where wooden parts are connected.

Ahşap, odun

WRAP Wrap electrical harness with spiral wrap.

Sarmak, örtmek, sarılmak, katlamak, ucunu bükmek,

WRIST ANKLE

The human body is a good electrical conductor and electrostatic charges on the body can be dissipated by skin contact with a grounding device such as a wrist or anklestrap.

El Bileği, Ayak bileği,

YAW The flight control system provides aircraft pitch, roll and yaw control around the three axis (lateral, longitudinal and vertical) in all phases of flight

Sağa sola kayış, uçağın yatış yapmadan sağa sola dönmesi, dikey eksen etrafında dönmek,

YOKE A control column head gear set connects the control wheel to the control column torque tube through a yoke and a fork connection.

Boyunduruk, boynuz

- 121 -

ZONE The airflow in the primary zone has a circular flow pattern, which causes the spray of fuel to mix fully with combustion air.

Bölge, bölüm, alan, kısım,