OCE CS9050 Operation Instructions Book
-
Upload
necunoscatorul -
Category
Documents
-
view
230 -
download
0
Transcript of OCE CS9050 Operation Instructions Book
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 1/68
Océ CS9050
Eco Solvent Operation Instructions
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 2/68
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 3/68
Operation Instructions CS9050
AP-40784 - Revision 1.0 3
Copyright notice
COPYRIGHT © 19/6/08 Océ-Technologies B.V.All rights reserved.
Océ-Technologies B.V. reserves the right to modify the information contained in this manual at
any time without prior notice.
This document may not be reproduced by any means, in whole or in part, without written
permission of the copyright owner.
This document is furnished to support the Océ CS9050 series printers. In consideration of
the furnishing of the information contained in this document, the party to whom it is given,
assumes its custody and control and agrees to the following:
The information herein contained is given in confidence, and any part thereof shall not be
copied or reproduced without written consent of Océ-Technologies B.V.
This document or the contents herein under no circumstances shall be used in the
manufacture or reproduction of the article shown and the delivery of this document shall not
constitute any right or license to do so.
19 June 2008
Published: Océ-Technologies B.V.,
St. Urbanusweg 43
Venlo, The Netherlands,
P.O. Box 101, NL 5900 MA Venlo
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 4/68
Operation Instructions CS9050
4 AP-40784 - Revision 1.0
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 5/68
Operation Instructions CS9050
AP-40784 - Revision 1.0 5
Table of contents
Chapter 1 Safety instructions- - - - - - - - - - - - - - - - - - - - - - - - - 9
1.1 Compliance with the following regulations - - - - - - - - - - - - - - 9
1.2 Managing VOCs - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 10
1.3 Handling inks + waste- - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11
1.4 Warnings, cautions and notes - - - - - - - - - - - - - - - - - - - - - - 11
1.5 Safety instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 12
1.6 Warning labels - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 14
Handling the operation procedure labels - - - - - - - - - - - - - - - - - - - 14
Chapter 2 Product overview- - - - - - - - - - - - - - - - - - - - - - - - - 15
2.1 Names of parts and functions- - - - - - - - - - - - - - - - - - - - - - - 15
Front section- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 15
Rear section - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 16
Operation Panel - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
2.2 In-The-Box contents - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Items in the printer box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 22
Items in the Waste fluid tank box - - - - - - - - - - - - - - - - - - - - - - - - - 23
Items in the accessory bag - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 23
Items in the starter kit - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 24
Items in the stand box - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
2.3 Installation requirements - - - - - - - - - - - - - - - - - - - - - - - - - - 26
Installation environmental conditions for installation - - - - - - - - - - 26
Installation space - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 27
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 6/68
Operation Instructions CS9050
6 AP-40784 - Revision 1.0
Chapter 3 Basics - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29
3.1 Power cable connection - - - - - - - - - - - - - - - - - - - - - - - - - - - 29 Connection procedure - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29
3.2 Connecting the printer to PC- - - - - - - - - - - - - - - - - - - - - - - - 31
System requirements - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 31
Preparing cables - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 31
Connecting a network interface cable - - - - - - - - - - - - - - - - - - - - - - 31
3.3 Switching the power ON/OFF - - - - - - - - - - - - - - - - - - - - - - - 33
Switching the power ON - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 33
Switching the power OFF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 33
3.4 Installing ink cassettes for the first time - - - - - - - - - - - - - - - 35
Replacing ink cassettes- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 37
3.5 Disposal of waste fluids - - - - - - - - - - - - - - - - - - - - - - - - - - - 39
Disposal period - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 39
Disposal method - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 39
3.6 Transfer and transportation - - - - - - - - - - - - - - - - - - - - - - - - 40
Transferring the printer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 40
Transporting the printer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 42
3.7 Handling and installing media- - - - - - - - - - - - - - - - - - - - - - - 43
Installing roll media - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 43
Setting roll media- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 45
3.8 Performing a nozzle check - - - - - - - - - - - - - - - - - - - - - - - - - 48
3.9 Head height adjustment - - - - - - - - - - - - - - - - - - - - - - - - - - - 49
3.10 Media feed compensation - - - - - - - - - - - - - - - - - - - - - - - - - - 50
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 7/68
Operation Instructions CS9050
AP-40784 - Revision 1.0 7
Chapter 4 Periodical maintenance - - - - - - - - - - - - - - - - - - - - 55
4.1 Done by end user - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 55 Cleaning the printer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 56
Cleaning the outer case - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 56
Cleaning the inside of the printer - - - - - - - - - - - - - - - - - - - - - - - - - 56
Head cleaning - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 60
Cleaning the cleaning wiper - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 61
4.2 Done by Authorized Océ Technician- - - - - - - - - - - - - - - - - - 64
Periodical replacement of parts - - - - - - - - - - - - - - - - - - - - - - - - - - 64
Periodical inspection part list - - - - - - - - - - - - - - - - - - - - - - - - - - - - 64
Chapter 5 Menu overview- - - - - - - - - - - - - - - - - - - - - - - - - - - 65
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 8/68
Operation Instructions CS9050
8 AP-40784 - Revision 1.0
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 9/68
1
Operation Instructions CS9050
Safety instructions
AP-40784 - Revision 1.0 9
Chapter 1 Safety instructions
This chapter explains the installation of this printer, warning terms that operators need to
know, caution items and warning labels on the printer main unit.
1.1 Compliance with the following regulations
Important
When installing and operating this printer, be sure to follow the directions and
warnings in this guide.
The CE marking is a mandatory European marking for certain
product groups to indicate conformity with the essential health and
safety requirements set out in European Directives.
By affixing the CE marking, the manufacturer, his authorized
representative, or the person placing the product on the market or
putting it into service ensures that the item meets all the essential
requirements of all applicable EU directives and that the applicable
conformity assessment procedures have been applied.
Your product is designed and manufactured with high-quality
materials and components, which can be recycled and reused.
When this crossed-out wheeled bin submenu is attached to a
product, it means the product is covered by the European Directive
2002/96/EC - WEEE regulation.
Please inform yourself about the local separate collection system for
electrical and electronic products.
Please act according to local rules and do not dispose of your old
products with your normal household waste. The correct disposal ofyour old product will help prevent potential negative consequences
for the environment and human health.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 10/68
Operation Instructions CS9050
Safety instructions
10 AP-40784 - Revision 1.0
1.2 Managing VOCs
During the operation of the Océ CS9050 volatile organic compounds (VOCs) will
release originating from the Eco-solvent ink. In order to avoid any health risk the user
needs to take all necessary precautions in accordance with all applicable local, state
and federal regulations.
Océ recommends a minimum ventilation of 150 m3/hr. This means that for a Océ
CS9050 installed in a room with a volume of 50 m3, a ventilation rate of at least 3 times
per hour is necessary i.e. the room volume of 50 m3 has to be refreshed three times
per hour. The recommended ventilation should be applied in case the printer is used at
nominal printing speed (7m2/h) at daily print volumes of 21 m2/day (3 times the
average intended use). In case of more intensive use of the printer, the ventilation
frequency should be increased accordingly.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 11/68
Operation Instructions CS9050
Safety instructions
AP-40784 - Revision 1.0 11
1
1.3 Handling inks + waste
Before handling inks / cleaning fluids and their waste, please read the Material Safety
Data Sheets (MSDS) and the labels for important health, safety and environmental
information carefully. All safety data sheets are periodically updated. These sheets and
their translations can be found on the MSDS CD.
Only use original manufacturer’s ink and appropriate cleaning liquid. Before installing an ink
holder, shake it gently. Doing so will preserve print quality.
When ink is moved from a cold place to a warm place, keep the ink for three hours or more
in the new printing environment before printing.
Do not disassemble ink holders. Otherwise, ink may get in your eyes or on your skin. A
disassembled ink holder can not be used either.
When refilling ink, use original manufacturer’s ink. Our Océ printers are designed to use
original ink.
If you use ink which are not produced by the original manufacturer:
Printing might become blurred and the end of the ink in the holder might not be
detected correctly.
Any problems caused by using an ink holder other than those recommended above will
not be covered by the warranty, and repair expenses will be paid by the customer.
For handling waste: refer to section 13 on the MSDS-sheet.
Inks / Waste
General advice: wear safety glasses and gloves especially when handling the waste
ink.
After spill: remove contaminated clothing.
After inhalation: if difficulties occur after vapour / aerosol has been inhaled, remove to
fresh air and seek medical attention.
After skin contact: wash thoroughly with soap and water.
After eye contact: wash affected eyes for at least 15 minutes under running water while
the eyelids are held open.
After swallowing: rinse mouth and drink plenty of water. Never induce vomiting.
1.4 Warnings, cautions and notes
Safety terms in this manual and the contents of warning labels attached to the printer are
categorized into the following three types, depending on the degree of risc (or the scale of
accident).
Read the following explanations carefully and follow the instructions in this manual.
Safety terms Details
Important Must be followed carefully to avoid death or serious bodily injury.
CautionMust be observed to avoid bodily injury (moderate or light) or damage to
your equipment.
NotesContains important information and useful tips on the operation of your
printer.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 12/68
Operation Instructions CS9050
Safety instructions
12 AP-40784 - Revision 1.0
1.5 Safety instructions
Machines must be installed according to Océ’s Installation Guide also after moving
machines to another location; maintenance needs to be done according to the
maintenance manual.
To prevent fire or electrical shock, never use a power supply source other than the one
rated for the product in the country where you purchased the product.
To prevent fire or electrical shock, machines must be connected to a properly grounded
electrical power outlet. Do not connect the power cable to a power strip or a power source
shared by other electrical devices.
Make sure that no foreign substances such as dust etc. are stuck to the power plug.
Make sure that the power plug is firmly inserted to the edge of the power socket.
Use only the provided power cable. To prevent fire or electrical shock, follow theinstructions below when handling the power cable:
Do not cut or modify the cable.
Do not put heavy objects on the cable.
Do not bend, twist, knot or pull the cable.
Do not wire the cable near equipment that generates heat.
Do not use the cable with any other electrical device.
Do not handle the cable with wet hands.
Be aware of all caution and warning labels to avoid potentially hazardous situations.
Do not disable any safety precautions systems.
Do not operation the unit unless all parts are mounted.
Do not stand on or place heavy objects on your machine. Doing so may result in the
machine tipping or falling over and causing injury.
Do not place the machine in humid and dusty areas or in areas exposed to flammables.
Doing so may result in electrical shock or fire.
Do not place the machine in the following areas. Doing so may result in the machine
tipping or falling over and causing injury.
Unstable surfaces
Sloping floors
Areas subject to vibration by other equipment.
Do not cover the ventilation hole of your machine with cloth, such as a blanket or tablecloth. Doing so could obstruct ventilation and cause fire.
Do not insert or drop metal or inflammable objects into openings, such as ventilation
outlets. Doing so may result in electrical shock and fire.
Do not touch the media guide during printing. It is hot and may cause a burn.
Do not touch the media feed slot, platen or media guide while heaters are operating. They
are hot and may cause a burn.
Keep the machine horizontally during transportation.
To prevent back pains and other injuries, always work with at least 4 people to unpack or
move the machine.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 13/68
Operation Instructions CS9050
Safety instructions
AP-40784 - Revision 1.0 13
1
Stop using your machine if a liquid has been spilled into it. This may cause electrical shock
or fire. Switch the machine off as soon as possible, unplug the power cord, and contact
your local Océ representative.
Be sure to power OFF the machine and unplug the power cable from the outlet before
cleaning the machine. Use a damp cloth to clean the machine. Do not use thinner,
benzene, alcohol or other active agents. Doing so may result in damage or paint peeling
from the casing.
Do not bend or pull the waste fluid tube. Doing so may cause waste fluid to leak out and
malfunction of the product.
Do not tilt the machine, place it against a wall or turn it upside down. Doing so may cause
ink to leak inside the machine. Movement after transport is also not covered by the
warranty.
When cutting roll media, be careful of the following. Incorrect handling can result in injury
to the hands and fingers from the razor blade.
When holding the media, do not place fingers over the media cut groove.
Move the razor blade slowly along the media cutting groove.
Do NOT transport the machine to another room without contacting your local Authorized
Océ representative.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 14/68
Operation Instructions CS9050
Safety instructions
14 AP-40784 - Revision 1.0
1.6 Warning labels
A warning label is used on parts of the printer which especially needs your attention.
Understand the locations and the descriptions of the danger associated with each label
before operating the printer.
1.6.1 Handling the operation procedure labels
Be sure to read and understand the safety warnings before handling the printer.
N° Description
1
2
3
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 15/68
2
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 15
Chapter 2 Product overview
This chapter explains the features of the printer along with the names and functions of each
part.
2.1 Names of parts and functions
This section explains the names and functions of each part.
2.1.1 Front section
Be sure to read and understand the safety warnings before handling the printer.
N° Description Function
1 Media loading lever Used to release or fix the media
2 Operation panelOperation condition setting, printer display and various
function settings are performed.
3 Front cover
Used to prevent that a user comes in contact with the
driving mechanism during the print operations. It is
normally closed
4 Stand To install the printer on a level floor.
5 Book holder Quick reference manual etc. can be stored here.
6 Media guide
Used to feed media smoothly when the media is set or
printed. The printer has also an incorporated heater (after
heater) to dry ink.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 16/68
Operation Instructions CS9050
Product overview
16 AP-40784 - Revision 1.0
2.1.2 Rear section
7 Media cut grooveInstalled inside of the front cover. Used to cut media
straight.
8 Pressure rollersInstalled inside of the front cover.
Press and hold the media when printing.
9 PlatenInstalled inside of the front cover.
The heater (platen heater) to dry ink is installed.
N° Description Function
N° Description Function
1 AC inlet Used to connect the power cables
2 Network interface connector Connects a network interface cable
3 USB connector Not used in this printer
4 Scroller receiver Set the scroller when roll media is used.
5 Media feed slot Used to feed media
6 Ink cassette slot Insert the ink cassette
7 Media guide
Used to feed the media smoothly through.
The heater (pre heater) to warm media is
installed
8 Waste fluid tankUsed to collect waste ink discharged from the
printer.
9 Waste fluid valve
Open and close when discharging the waste
fluid from the waste fluid tank. the default
position is closed.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 17/68
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 17
2
2.1.3 Operation Panel
Note
The operation keys are assigned with different functions and names depending
on the printer status(Normal or Setup menu display)
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 18/68
Operation Instructions CS9050
Product overview
18 AP-40784 - Revision 1.0
Operation keys
N° Key Normal Setup menu display
1 [Menu] keyShifts to the Setup
menu.Shifts from Setup menu display to Normal.
2
[Enter] keyRestarts printing
during printing.
Shifts to the selected menu
The setting is determined and saved.
[Cleaning] key
Press and hold this
key for two seconds
or more to clean the
print head.
—
3 [Cancel] key
When printing:
Forcefully
terminates printingand deletes one
file of the
remaining data.
When receiving or
analysing:
Deletes data that
are already
received and
analysed, and
delete the next
data.
Returns to the previous menu hierarchy.
Changes made in the setting are
discarded.
Shifts from Setup menu display to
Normal.
4
[<] key —The following menu changes the set value.
Origin menu
[Nozzle Check]
key
Press and hold this
key for two seconds
or more to perform
Nozzle Check
printing.
—
5 [>] key
Sets Cleaning Mode.
The lamp of Cleaning
Mode lights up in
green.
Down the menu level in the directory tree.
6
[Backward↑] keyMedia is fed in the
reverse direction.—
[+] key —
Changes to the previous item in the
displayed menu.
The setting is changed to the forward
direction.
The numeric value is increased during
numerical input.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 19/68
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 19
27
[Forward↓] keyMedia is fed in the
forward direction.—
[–] keyPause to print during
printing.
Changes to the previous item in the
menu.
The setting is changed to the reverse
direction.
The numeric value is decreased during
numerical input.
8 [Power] keySwitches the printer
ON and OFF.Switches the printer ON and OFF.
N° Key Normal Setup menu display
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 20/68
Operation Instructions CS9050
Product overview
20 AP-40784 - Revision 1.0
Display section
N° Name Color Status Description
9 Power lamp Green
Lamp
ONPower ON.
Lamp
blinks
An error has occurred.
Error content is displayed on the LCD.
Lamp
OFFPower OFF.
10 Data lamp Orange
Lamp
ON
Analysing received data.
Under printing.
Lamp
blinks
Receiving data.
Lamp
OFFData is not received and analysed.
11 High lamp Green
Lamp
ONThe head height is set to High.
Lamp
OFFThe head height is set to Low.
12 Low lamp Green
Lamp
ONThe head height is set to Low.
Lamp
OFFThe head height is set to High.
13 Wave lamp Green
LampON
The Effect menu is set to Wave or Fuzz.
Lamp
OFFThe Effect menu is set to None.
14Fine &S.Fine
lampGreen
Lamp
ONThe Effect menu is set to Fine or Super Fine.
Lamp
OFF
The Effect menu is set to Wave or Fuzz.
When the Wave lamp is switched OFF, the
Effect menu is set to None.
15 Strong lamp Green
Lamp
ON
Cleaning Mode is set to Strong.
When the Normal lamp is also switched on,Cleaning Mode is set to Economy.
Lamp
OFFCleaning Mode is set to Normal.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 21/68
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 21
216 Normal lamp Green
LampON
Cleaning Mode is set to Normal.
When the Strong lamp is also switched on,
Cleaning Mode is set to Economy.
Lamp
OFFCleaning Mode is set to Strong.
17LCD display
section— —
Displays operation status of the printer or an error
message.
N° Name Color Status Description
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 22/68
Operation Instructions CS9050
Product overview
22 AP-40784 - Revision 1.0
2.2 In-The-Box contents
2.2.1 Items in the printer box
2
5
1
43
N° Description Qty
1 Printer main body 1
2 A0 Scroller 3 inch 1
3 Waste fluid tank box 1
4 Accessory bag 1
5 Power cable 1
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 23/68
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 23
2
2.2.2 Items in the Waste fluid tank box
2.2.3 Items in the accessory bag
1 2
3
N° Description Qty
1 Waste Fluid tank 1
2 Waste fluid tank holder 1
3 Waste fluid tank holder stabilizing screws 4
3 4
1 2
N° Description Qty
1 Operation manual CD 1
2 Quick reference 1
3 Installation manual 1
4 Poly-knit wiper 10 sheets
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 24/68
Operation Instructions CS9050
Product overview
24 AP-40784 - Revision 1.0
2.2.4 Items in the starter kit
N° Description Qty
1 Power cable EU 4.5m rightangle 1
2 Power cable UK 4.5m rightangle 1
3
Ink starter kit
Cleaning cassettes
Ink cassettes
1
4
4
4 User’s Guide (Océ Europe version) 1
5 Installation guide 1
6 Wave stitching documentation 1
7 Polyknit wiper 30
8 PE gloves 100 Pcs
9 Eco-Solvent cleaning 250 ml
10 CD with Océ manuals 1
11 Océ CS9050 name plate 1
12 Powered by “Onyx” decall 1
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 25/68
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 25
2
2.2.5 Items in the stand box
1 2
4
3
76
8 9
5
N° Description Qty
1 Left support 1
2 Right support 1
3 Caster section (left, right) 2
4 Central beam 1
5 Stabilizer 1
6 Book holder 1
7 Hexagon socket head cap screw 12
8 Butterfly bolt 2
9 Hexagon wrench 1
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 26/68
Operation Instructions CS9050
Product overview
26 AP-40784 - Revision 1.0
2.3 Installation requirements
2.3.1 Installation environmental conditions for installation
Note
Do not open the front cover during printing.
If the front cover is opened, printing will be interrupted.
Printing restarts if you close the front cover. However, you are not guaranteed
to have high print quality.
Be sure to read and understand the safety warnings before handling the printer.
Floor strength of the installation place More than 2940 Pa (300 kg/m²)
Power specifications
Power supply AC 90 V - 120 V
Frequency range 50/60Hz
Power capacity 10A or more
Environmental
conditions
Operative conditionTemperature: 20°C to 32°C
Humidity: 40% to 60%, No condensation
Guaranteed range of
printing accuracy
Temperature: 20°C to 32°C
Humidity: 40% to 60%
Change rateTemperature: Within 2°C per hour
Humidity: within 5% per hour
Archiving
environment
Temperature: -20°C to 60°CHumidity: 20% to 80%
no condensation
Note
Concerning temperature and humidity, avoid:
Places where temperature or humidity may rapidly change, even though within the
required conditions.
Places that receive direct sunlight, increased illumination or direct air, for example
from an air conditioner.
To keep the temperature and humidity constant, install this product in alocation where the air condition is adjustable.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 27/68
Operation Instructions CS9050
Product overview
AP-40784 - Revision 1.0 27
2
2.3.2 Installation space
Install the printer on a levelled floor which has enough strength to support the weight of theentire machine.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 28/68
Operation Instructions CS9050
Product overview
28 AP-40784 - Revision 1.0
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 29/68
3
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 29
Chapter 3 Basics
3.1 Power cable connection
This section explains power cable connection.
3.1.1 Connection procedure
Step 1: Make sure that the printer is switched OFF.
Note
Be sure to use the power cable supplied with the printer.
Using other power cables can cause an electric shock or fire.
Do not use a damaged power cable. It could lead to an electric shock and fire.
Be sure to read and understand the safety warnings before handling the printer.
Note
The power is ON when the [Power] key of the operation panel is pressed in.
Press the key once again to switch OFF the power.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 30/68
Operation Instructions CS9050
Basics
30 AP-40784 - Revision 1.0
Step 2: Connect the power cable to the AC inlet on the back of the printer.
Step 3: Insert the power cable plug firmly in the socket.
N° Description
1 AC inlet
2 Power cable
Note
If a power cable is damaged, contact your local Océ representative.
Note
If you cannot use earth terminals nor find any of them, contact your local Océ
representative.
Do not unplug the power cables when the printer is ON. If the power cables
have been unplugged, leave the printer for at least 1 minute before plugging
the cables back in.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 31/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 31
3
3.2 Connecting the printer to PC
3.2.1 System requirements
The following are the system requirements for this printer and software server RIP (optional).
3.2.2 Preparing cables
The printer is equipped with a network interface to connect with a PC.
You need a network interface cable to connect a PC with this printer.
Prepare the cable depending on the PC that it will be connected to.
3.2.3 Connecting a network interface cable
Step 1: Switch OFF both the printer and PC.
Step 2: Insert the connector of the network interface cable into the network interface
connector located in the back of the printer.
Operating system Windows 2000 Professional, Windows XP
CPU Pentium III processor 1 GHz or more
Memory (RAM) 512 MB or more
Hard disk free space 10 GB or more
Note
The required memory varies depending on the application software or the print
data type.
A large hard disk and memory are recommended.
N° Description
1 Network interface cable
2 Network interface cable connector
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 32/68
Operation Instructions CS9050
Basics
32 AP-40784 - Revision 1.0
Step 3: Fix the network interface cable to the cable clamp.
Step 4: Connect the other connector of the network interface cable to your PC.
N° Description
1 Network interface cable
2 Cable clamp
Note
For network setting on the side of the printer, refer to “the Panel setup menu”
in the User’s Guide.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 33/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 33
3
3.3 Switching the power ON/OFF
3.3.1 Switching the power ON
Step 1: Press the [Power] key on the operation panel to switch ON the printer.
The Power lamp on the operation panel lights up in green.
The printer starts initial operation.
When the initial operation is complete, the printer enters Normal.
3.3.2 Switching the power OFF
Step 1: Verify the following regarding the operational condition of the product.
Printing or other operations are not in progress.
The operation panel display is Normal.
The Low lamp on the operation panel lights up in green.
Step 2: Press the [Power] key on the operation panel to switch OFF the printer.
The Power lamp on the operation panel switches OFF.
"Power OFF" is displayed on the operation panel.
Note
If there is a problem during the initial operation, a message is displayed on the
operation panel and the printer may stop operating.
In case the operation stops, refer to the “Troubleshooting” chapter in theUser’s Guide.
Be sure to read and understand the safety warnings before handling the printer.
Note
If the [POWER] key is pressed or the power indication light lights up green, the
power is ON.
Press the key once again and switch OFF the power.
Note
If the head height is set to High, "Change Head Gap Low" is displayed on the
operation panel and the procedure to switch the power OFF stops.
To restart the procedure, return the head height to Low.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 34/68
Operation Instructions CS9050
Basics
34 AP-40784 - Revision 1.0
All the lamps on the operation panel and the LCD monitor are switched OFF.
The printer automatically switches the power OFF.
Step 3: When not using the printer for a long period, push the media loading lever to the
back.
Note
If there is a problem during the power OFF operation, a message is displayed
on the operation panel and the printer may stop operating.
In case the operation stops, refer to the troubleshooting chapter in the User’s
Guide.
After switching OFF the printer, wait for 10 seconds or longer to switch it ON
again.
N° Description
1 Media loading lever
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 35/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 35
3
3.4 Installing ink cassettes for the first time
Step 1: Switch the unit ON.
The printer starts the initializing operation.
The operation panel displays “[Start ink charge ==> E]”, press Enter.
The operation panel displays “during washing”.
The shipping liquid is being flushed out.
If the operation panel displays “Wash retry?” select Yes. (Repeat “Wash retry”until cleaning liquid is coming through to the tank, then select ‘NO’.
The operation panel displays “insert cleaning cartridges”.
Step 2: Take a cleaning cassette out of the bag.
Note
When filling ink in the machine, use the ink of original product manufacturer.
This printer has been adjusted for the use of genuine ink cassettes. In case of
using ink cassettes which are not a product of the original manufacturer,
Printing might become blurred and end of ink in the cassette might no longer be
correctly detected.
The problems caused by doing so will not be covered by the warranty and repair
expenses will be paid by the customer.
Do not shake the ink cassettes strongly, this to avoid ink leaking out of the
cassette.
Do not disassemble the ink cassette. A disassembled ink cassette cannot be
used.
Make sure to use a dedicated cleaning fluid.
Before installing the ink cassette, shake it gently. Doing so will preserve
printing quality.
When storing the ink cassettes in a cold room, be sure to take them out of
stock at least 3 hours before using them.
Insert or remove the ink cassettes not more than 10 times.
If the ink cassette is inserted or removed 10 times or more, it cannot be used
even if there is some remaining ink inside.
A dedicated smart chip is included with the ink cassette for this printer. If you
insert or remove the ink cassette during printing, information contained in the
smart chip may be damaged and the ink cassette may be obsolete.
Be sure to read and understand the safety warnings before handling the printer.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 36/68
Operation Instructions CS9050
Basics
36 AP-40784 - Revision 1.0
Step 3: Install the cleaning cartridge into the ink cartridge slot.
Keep the mark of the cleaning cartridge facing up and insert it into the slot of the
printer. Insert the cleaning cartridge all the way to the end of the slot.
The printer starts filling cleaning fluid.
Step 4: After the cleaning fluid is filled, take out the cleaning cartridge.
"During washing" is displayed on the operation panel and the printer starts Head
washing.
After the Head washing is complete, "Insert InkCartridges" is displayed on the
operation panel.
Step 5: After the Head washing is complete, take out the ink cartridge from the bag and
shake it gently two to three times.
Slots for ink cartridges are specified depending on the colours of the ink
cartridge.
Match the mark on each slot with the color of the ink cartridge.
Keep the mark of the ink cartridge facing up and insert it into the slot of the
printer.
Insert the ink cartridge all the way to the end of the slot.
“Ink Refill//%” is displayed on the operation panel and ink replenishment starts.
Ink replenishment takes about 4 minutes.
Ink filling operation and pause operation are repeated during the inkreplenishment.
When “100%” is displayed, the ink replenishment is complete.
N° Description
1 Cleaning cassette
2 ink cassette slots
Note
Do not perform the following operations during ink filling.
Do not switch the printer OFF.
Do not unplug the power cable.
Do not open the front cover.
Do not push the media loading lever backward.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 37/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 37
3
After the ink replenishment is complete, "Media End" is displayed on the
operation panel.
3.4.1 Replacing ink cassettes
Replacement time
When “[****] InkNearEnd” is displayed on the operation panel.
This message is displayed when there is a small amount of ink remaining in the ink
cassette.
The alarm buzzer sounds.
To stop the buzzer, press the [ENTER] key on the operation panel.
Replace with the new ink cassette.
When “[****]InkEnd” is displayed on the operation panel.
This message e is displayed when there is no ink remaining in the ink cassette.
The alarm buzzer sounds.
To stop the buzzer, press the [ENTER] key on the operation panel.
Immediately replace the empty cassette with a one.
Type
Our genuine ink cassettes which can be used with the CS9050 are as follows.
Note
If the printer perform the nozzle check printing immediately after initial ink
replenishment is complete, the following results may occur.
Printed lines become blurred.
The data is partially not printed.
In such cases, refer to “Head cleaning” in the User’s guide" and refill a small
amount of ink. Then, check the printing result.
If there is no improvement in the print result even after refill a small amount of
ink, leave the printer unused for an hour or more. Then, refill a small amount of
ink again and check the print result.
If there is still no improvement, contact your local Océ representative.
Description Model N°
IJC930 Eco-Solvent ink cartridge Black 0.22l 29952249
IJC930 Eco-Solvent ink cartridge Cyan 0.22l 29952250
IJC930 Eco-Solvent ink cartridge Magenta 0.22l 29952251
IJC930 Eco-Solvent ink cartridge Yellow 0.22l 29952252
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 38/68
Operation Instructions CS9050
Basics
38 AP-40784 - Revision 1.0
Replacement steps
Step 1: Verify that the printer has been switched ON.
Step 2: Remove the empty ink cassette from the ink cassette slot.
Step 3: Unpack the next ink cassette and insert it into the cassette slot.
Step 4: Verify that the printer returns to the Normal mode.
Note
Do not shake ink cassettes. Doing so may cause ink leakage
Do not disassemble the ink cassette. A disassembled ink cassette cannot be
used.
When an ink cassette is moved from a cold place to a warm place, keep the ink
cassette unused for 3 hours or more in the printing environment.
Do not refill the ink cassettes.
Doing so may result in incorrect printing.
Insert or remove the ink cassette at the time of replacement only.
Inserting or removing ink cassettes except at the time of replacement may
result in incorrect printing.
Note
Do not replace ink cassettes when the printer is switched OFF. Doing so may
result in incorrect detection of the remaining ink and result in abnormal
printing behaviour.
Note
A used ink cassette should be put in a vinyl bag or a bag used for this kind of
waste. Disposal of an ink cassette has to be done in compliance with the
regulations and instructions of the local authorities.
Note
Open the ink cassette solvent resistant blister just before attaching the ink
cassette into the cassette slot. Leaving the ink cassette open for a long time
may result in an abnormal print.
Replace the ink cassette within 6 months after installing it into the printer.
Insert or remove the ink cassette not more than 10 times. This to prevent that
the smart chip or its reader would be worn out and malfunction in this way. If
inserted or removed more than 10 times the ink cassette could malfunction
even if there is some ink remaining.
Note
The printer resumes printing when you have replaced (and) ink cassette(s)
after an ink end occurred during printing.
Be sure to read and understand the safety warnings before handling the printer.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 39/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 39
3
3.5 Disposal of waste fluids
3.5.1 Disposal period
Dispose of waste fluids in the following cases:
When the waste fluid tank is more than half full.
When “Waste Ink Tank Full” is displayed on the operation panel.
3.5.2 Disposal method
Step 1: Ready an empty container such as a supply waste fluid bottle, to contain the waste
fluid.
Step 2: Lay a protective material on the floor under the waste fluid tank.
Step 3: Open the waste fluid valve, and transfer the waste fluid to the container.
Step 4: After Transferring the waste fluid to the empty container, close the waste fluid valve
securely.
Step 5: Wipe the opening of the waste fluid valve with a cloth, etc.
Step 6: Dispose of the waste fluid as an industrial waste product.
Important
The waste fluid from the printer is industrial waste.
Proper waste fluid disposal according to industrial waste disposal laws andordinances of you local government is required.
Consign disposal of waste fluids to a specialized processor.
Note
When transferring the waste fluid to the empty container, the waste fluid may
splash. When transferring the waste fluid to the empty container, put the container
underneath and close the waste fluid valve afterwards.
N° Description
1 Waste fluid valve
2 Empty container
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 40/68
Operation Instructions CS9050
Basics
40 AP-40784 - Revision 1.0
3.6 Transfer and transportation
3.6.1 Transferring the printer
When using the dedicated stand, transfer the printer according to the procedure below.
Pre-transfer steps
Step 1: Dispose of waste fluid
Refer to Disposal of waste fluids on page 39.
Step 2: Make sure that the printer is switched OFF.Step 3: Check that the butterfly bolts (2) attaching the stand and the printer are not loosen.
Step 4: Check that the printer head is in the rightmost position
Step 5: Bind the CR belt in the centre section of the printer by fastening the CR belt clip
around it.
Step 6: Remove the scroller.
Step 7: Remove all the cables, such as the power cable.
Be sure to read and understand the safety warnings before handling the printer.
N° Description
1 CR belt
2 CR belt clip
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 41/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 41
3
Step 8: Release the lock of the caster and transfer it.
Reinstalling the printer
Step 1: After moving the printer, follow the procedure below to set it ready for use.
Step 2: Select a suitable place for installation
Refer to “Installation requirements on page 26.
Step 3: Move and install the printer to the location.
Step 4: Check the butterfly bolts (2) fixing the stand and the printer are well fixed.
Step 5: Attach all needed cables.
Step 6: Perform a nozzle check, and then confirm that there is no clogging in the print head.
Refer to “Performing a nozzle check on page 48”
Step 7: Perform Alignment.
Note
The casters supplied with the dedicated stand are manufactured for little
movement in flat indoor areas, not for transporting equipment.
When moving the printer outdoors in places with big step differences, move
the stand and the printer separately.
N° Description
1 Caster
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 42/68
Operation Instructions CS9050
Basics
42 AP-40784 - Revision 1.0
3.6.2 Transporting the printer
Pre-transportation procedure
Step 1: Switch ON the unit
Step 2: Confirm that the printer functions correctly.
Step 3: Remove all ink cassettes.
Step 4: Switch OFF the printer.
Step 5: Dispose of waste fluid
Refer to Disposal of waste fluids on page 39.
Step 6: Check that the printer head is in the rightmost position
Step 7: Bind the CR belt in the centre section of the printer by fastening the CR belt clip
around it.Step 8: Remove the scroller.
Step 9: Remove all the cables, such as the power cable.
Step 10: Remove the printer from the stand.
Step 11: Repack the printer.
Post-transportation procedure
Step 1: Perform unpacking, assembling and setting the printer as described in the
installation guide.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 43/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 43
3
3.7 Handling and installing media
3.7.1 Installing roll media
This section explains how to load roll media.
Use the exclusive scroller included with this printer for loading roll media.
Follow the procedure below to load roll media.
Step 1: Load roll media to the scroller so that it is rolled in an anti clockwise direction whenviewed from the fixed flange.
Step 2: Push the roll media until its core hits the right edge of the fixed flange.
Note
It is recommended to use tested and compatible media for this printer.
Note
The following roll media can be set on the scroller included with this printer.
Media tube diameter: three inches, outside diameter of media: 150 mm or less,
weight: 19 kg or less
Caution
Load roll media on an even surface such as a desk.
If you load roll media with the scroller standing vertical, there is a possibility
that the scroller might get damaged.
N° Description
1 Fixed flange
2 Roll media
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 44/68
Operation Instructions CS9050
Basics
44 AP-40784 - Revision 1.0
Step 3: Attach the movable flange firmly to the roll media core.
Step 4: Set the scroller to the scroller receiver facing the fixed flange to the side of the ink
cartridge slot.
N° Description
1 Movable flange
2 Roll media
N° Description1 Scroller
2 Fixed flange
3 Ink cassette slot
4 scroller receiver
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 45/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 45
3
3.7.2 Setting roll media
This section explains how to set roll media.Step 1: Switch ON the unit.
The printer starts the initializing operation.
"Media End" is displayed on the operation panel.
Step 2: Push the media loading lever to the back.
"Lever Up" is displayed on the operation panel.
Step 3: Set the roll media to the media feed slot.
Step 4: Open the front cover, and pull out the roll media.
Caution
Do not operate the media loading lever during initial operation.
The print head portion may touch the pressurizing roller portion, and cause
a malfunction
Note
If the roll media end gets loose, roll up the media again and load it.
N° Description
1 Roll media
2 Media feed slot
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 46/68
Operation Instructions CS9050
Basics
46 AP-40784 - Revision 1.0
Step 5: Holding the front edge of the roll media, roll it back using the scroller to remove a
bend and slant.
Step 6: Pull the media loading lever forward.
Step 7: Close the front cover.
The Media type setup menu is displayed on the operation panel.
Step 8: Press the [+] key or [–] key to select the type of the loaded media.
Step 9: Press the [Enter] key on the operation panel.
The media type is set.
"Media Initial" is displayed on the operation panel and media initial operation
starts.
After media initial operation is complete, "Ready to Print" is displayed on the
operation panel and the display shifts to Normal.
N° Description
1 Roll media
2 Scroller
Note
When loading the new roll media, cut the front edge of the media if it is not
straight.
Note
If the following operations are performed in the media type setup menu, the
printer starts media initial operation without specifying a media type.
Pressing the [Cancel] key on the operation panel.
No keys on the operation panel are pressed for 10 seconds.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 47/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 47
3
Step 10: Wind the roll media around the scroller to remove slack.
This completes media loading.
N° Description
1 Roll media
2 Scroller
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 48/68
Operation Instructions CS9050
Basics
48 AP-40784 - Revision 1.0
3.8 Performing a nozzle check
If the nozzle check result indicates that the checked points are blurred or missing, clean the
print head.
Step 1: Switch ON the printer and load the roll media. Refer to: Setting roll media on page 45
Step 2: Confirm that the printer functions normally.
Step 3: Press the [Nozzle Check] key on the operation panel for at least 2 seconds.
Perform the nozzle check printing.
Step 4: Check the print sample and confirm that the checked points are blurred or missing.
Step 5: If the nozzle check result indicates that the checked points are blurred or missing,
clean the head. Refer to: perform a head cleaning in the user’s guide.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 49/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 49
3
3.9 Head height adjustment
When used?
Use the head height adjustment feature to prevent the print head from touching the media,
when printing at high speeds or when using strongly curved media.
Procedure
Step 1: Open the front cover.
Step 2: Change the head height by moving the head height adjustment lever (orange).
The High lamp on the operation panel lights up in green.
Step 3: Close the front cover.
Note
If the head height adjustment lever is raised, high print quality will not be
guaranteed.
Do not open the front cover nor change the head height during printing. If the
head height is changed, the head alignment will be changed and high print
quality will not be guaranteed.
N° Description
1 Head height adjustment lever
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 50/68
Operation Instructions CS9050
Basics
50 AP-40784 - Revision 1.0
3.10 Media feed compensation
After every printed swat, the media is fed a certain distance. Depending on the kind of media
(weight, backing) another media feed compensation has to be set. This to avoid the following
phenomenon:
Printed swats overlap
White lines between every swat.
In such cases, follow the procedure below and adjust the media feed compensation value.
Step 1: Display the Media feed compensation menu on the operation panel.
Press the [Menu] key on the operation panel
“Menu1: Setup>] is displayed on the operation panel.
The operation panel shifts to the Setup menu display.
Press the [>] key on the operation panel.
“Set1: MediaType” is displayed on the operation panel.
Press the [ENTER] key on the operation panel.
“Media: Type1” is displayed on the operation panel.
Press the [+] key or [-] key on the operation panel to select the media type to
use.
Press the [ENTER] key on the operation panel.
“**>1: Print Mode” is displayed on the operation panel.
Press the [+] or [-] key to select “**2: PF Adjust”.
Press the [>] key on the operation panel.
“PF1: Initial Print” is displayed on the operation panel.
Proceed to Media feed compensation menu.
Step 2: Perform an initial adjustment print.
Press the [ENTER] key on the operation panel.
“FeedLength: 250mm” is displayed on the operation panel.
Note
The length of media that is fed for the initial adjustment print is normally set to
250 mm.
If you increase the feeding length, the accuracy of the media feedcompensation improves.
To change the feeding length, press the [+] or [-] key on the operation panel and
change the set value.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 51/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 51
3
Press the [ENTER] key on the operation panel.
“Printing” is displayed on the operation panel.
Start Initial adjustment printing.
When the initial adjustment printing is complete, the printer enters the Normal
status.
After the initial adjustment printing, cut the media.
Step 3: Measure the distance between the two pluses in the initial adjustment print using a
ruler.
Step 4: Sets up Initial Adjust Change.
Press the [+] key or [–] key on the operation panel to select "PF2: Initial Change".
Press the [Enter] key on the operation panel.
"Init.: 250.0/250 mm" is displayed on the operation panel.
Press the [+] key or [–] key on the operation panel and enter the measured value
in step 3.
Press the [Enter] key on the operation panel.
The initial adjustment value is saved.
"PF2: Initial Change" is displayed on the operation panel.
Step 5: Performs confirm print.
Press the [+] key or [–] key on the operation panel to select "PF3: Confirm Print".
Press the [Enter] key on the operation panel.
"Feed Length: 250 mm" is displayed on the operation panel.
N° Description
1 Feed length
2 Media feeding direction
Note
The length of media that is fed for the initial adjustment print is normally set to
250 mm.
If you increase the feeding length, the accuracy of the media feed
compensation improves.
To change the feeding length, press the [+] or [-] key on the operation panel and
change the set value.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 52/68
Operation Instructions CS9050
Basics
52 AP-40784 - Revision 1.0
Press the [ENTER] key on the operation panel.
"Printing" is displayed on the operation panel.
Start Confirmation adjustment printing.
When the Confirm Print is complete, the printer enters Normal.
After the confirmation adjustment printing, cut the media.
Step 6: Measure the distance between the two pluses in the confirmation adjustment print
using a ruler. Then, confirm that the distance matches the feeding length when
printing.
If the distance does not match the feeding length, follow the procedure from Step
1 to Step 5 and readjust.
If the distance matches the feeding length, proceed to step 7.
N° Description
1 Feed length
2 Media feeding direction
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 53/68
Operation Instructions CS9050
Basics
AP-40784 - Revision 1.0 53
3
Step 7: Perform Micro adjustment printing.
Display the Media feed compensation menu on the operation panel in the same
way as in step 1. Press the [+] key or [–] key on the operation panel to select "PF4:Micro Print".
Press the [Enter] key on the operation panel.
"Printing" is displayed on the operation panel.
Start Micro adjustment printing.
After the micro adjustment printing is completed, "PF4:Micro Print" is displayedon the operation panel.
Step 8: Refer to the illustrations below and check the printing result.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 54/68
Operation Instructions CS9050
Basics
54 AP-40784 - Revision 1.0
Step 9: Sets up Micro Adjustment Change.
Press the [+] key or [–] key to select "PF5:Micro Change".
Press the [Enter] key on the operation panel.
"Micro: 0pulse" is displayed on the operation panel.
Press the [+] key or [–] key and enter the micro adjustment value according to
the printing result in Step 7.
Press the [Enter] key on the operation panel.
The micro adjustment value is saved.
"PF5:Micro Change" is displayed on the operation panel.
Press the [Cancel] key on the operation panel several times.
The operation panel returns to Normal.
Step 10: The adjustment of media feed compensation value is complete.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 55/68
4
Operation Instructions CS9050
Periodical maintenance
AP-40784 - Revision 1.0 55
Chapter 4 Periodicalmaintenance
4.1 Done by end user
This section describes the periodical services requited on a CS9050 series printer. The
periodical maintenance ensures stable printout quality of the machine. In the periodical
maintenance, some service parts need to be checked, cleaned ore replaced.
Perform periodical inspections according to the table below.
Available articles for the end user and the order number
Important
Be sure to wear gloves when working with inks or cleaning liquid.
N° ction Frequency
1 Clean the wiper Weekly
2 Clean around the bottom of the head Weekly
3 Replace the spitting box sponges bi-monthly
Note
"Do not insert or drop metal or other objects through openings of the printer. It
could lead to an electric shock and / or fire.
"When substances or liquids such as water entered the printer, do NOT use the
printer. It could lead to an electric shock and/or fire. Immediately
Switch OFF the printer.
Disconnect the power plugs from the electric sockets.
Contact your local Océ representative.
N° Description part N°
1 PE gloves Handygrip (100 Pcs) 00000018
2 Swabs & Applicator foam (50 Pcs) 29800023
3 Eco solvent cleaning 250 ml 29952273
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 56/68
Operation Instructions CS9050
Periodical maintenance
56 AP-40784 - Revision 1.0
4.1.1 Cleaning the printer
Periodic cleaning is necessary to use the printer in good condition.
4.1.2 Cleaning the outer case
This sub-section describes how to clean the outer case.
Wipe out dust and dirt attached to the outer case by using a soft cloth.
4.1.3 Cleaning the inside of the printer
This sub-section describes how to clean the inside of the printer.
Follow the procedure below.
Step 1: Open the front cover.
Step 2: Remove paper powder and dust attached to the pressure rollers using a soft brush.
Be sure to read and understand the safety warnings before handling the printer.
Note
Do not blow paper powder inside the printer using tools such as an air duster.
It may cause an abnormal noise from the inside of the printer.
N° Description
1 Pressure roller
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 57/68
Operation Instructions CS9050
Periodical maintenance
AP-40784 - Revision 1.0 57
4
Step 3: Apply a damp and tightly squeezed soft cloth to wipe out paper powder and ink
attached to the platen and media guide.
Step 4: Apply a damp and tightly squeezed soft cloth to wipe off the dirt of the unpainted
(silver colour) area in the centre of the grid roller.
N° Description
1 Platen
2 Media guide
N° Description
1 Grid roller
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 58/68
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 59/68
Operation Instructions CS9050
Periodical maintenance
AP-40784 - Revision 1.0 59
4
Clean the P-rear sensor surface
Step 1: Open the front cover Step 2: clean the P-rear sensor surface with a swab.
N° Description
1 P-rear sensor
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 60/68
Operation Instructions CS9050
Periodical maintenance
60 AP-40784 - Revision 1.0
4.1.4 Head cleaning
If printed data is blurred or lacks part of it, clean the print head surface and nozzles (Headcleaning).
Follow the procedure below to perform Head cleaning.
Step 1: Confirm that the operation panel is Normal.
Step 2: Confirm that the media loading lever is returned to the front.
Step 3: Press the [>] key on the operation panel to select the cleaning mode.
Step 4: Press the [Cleaning] key on the operation panel for at least 2 seconds.
"Cleaning **%" is displayed on the operation panel.
Start Head cleaning.
After Head cleaning is complete, the operation panel shifts to Normal.
Note
When not using the printer for a long period (one week or more), perform a
Head cleaning once a week.
If not performing a Head cleaning, the print head is clogged. Doing so will
preserve print quality.
Remove media when cleaning.
Cleaning with media loaded may lead head crashes
Note
If blurs or lacking parts in printed media do not disappear with one time of
Head cleaning, perform Strong cleaning.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 61/68
Operation Instructions CS9050
Periodical maintenance
AP-40784 - Revision 1.0 61
4
4.1.5 Cleaning the cleaning wiper
This sub-section describes how to clean the cleaning wiper.
Cleaning time
Once a week, or when blurs or lacking parts appear on printed media after Head cleaning.
Cleaning method
Follow the procedure below to clean the cleaning wiper.
Step 1: If the printer is switched ON, make sure that:
Printing or other operations are not in progress.
The operation panel display is Normal.
Step 2: Display the CR Maintenance menu on the operation panel.
Press the [Menu] key on the operation panel.
"Menu 1: Setup>" is displayed on the operation panel.
The operation panel shifts to the Setup menu display.
Press the [>] key on the operation panel.
"Set1: MediaType" is displayed on the operation panel.
Press the [+] key or [–] key to select "Set20: CR Maintenance". Press the [Enter] key on the operation panel.
"CR Mainte.: Start" is displayed on the operation panel.
The display enters the CR Maintenance menu.
Step 3: Press the [Enter] key on the operation panel.
Maintenance starts.
The print head moves to centre.
"CR Maintenance: End" is displayed on the operation panel.
Note
Use the poly-knit wiper to clean the cleaning wiper.
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 62/68
Operation Instructions CS9050
Periodical maintenance
62 AP-40784 - Revision 1.0
Step 4: Open the front cover.
Step 5: Use the poly-knit wiper to remove the ink and dust on the cleaning wiper.
Cleaning wiper front side:
Remove the ink and dust to right and left.
Caution
While cleaning the cleaning wiper
Do not touch the cleaning wiper and head cap unit.
Head cleaning may not be performed correctly because of oil from your hands.
Make sure to wipe the print head with a dry poly-knit wiper.
A wet poly-knit wiper may cause the print head to clog.
N° Description
1 Cleaning wiper
2 Poly-knit wiper
3 Head cap unit
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 63/68
Operation Instructions CS9050
Periodical maintenance
AP-40784 - Revision 1.0 63
4
Cleaning wiper back side:
Remove the ink and dust upward.
Step 6: Close the front cover.
Step 7: Press the [Enter] key on the operation panel.
The print head returns to its original position.
"CR Mainte.: Start" is displayed on the operation panel.
Step 8: Press the [Cancel] key on the operation panel.
The printer enters Normal.
Cleaning of the cleaning wiper is complete.
N° Description
1 Cleaning wiper
2 Poly-knit wiper
3 Head cap unit
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 64/68
Operation Instructions CS9050
Periodical maintenance
64 AP-40784 - Revision 1.0
4.2 Done by Authorized Océ Technician
This section describes the periodical part replacement and the periodical inspections required
for this printer. Theses periodical services ensure the stable printing quality of this printer.
4.2.1 Periodical replacement of parts
Perform periodical replacements according to the table below. These replacements should be
replaced by an authorized Océ technician.
4.2.2 Periodical inspection part list
Perform periodical inspections according to the table below and perform cleaning and part
replacement as necessary.
Part Timing
Maintenance station Once a year
Wiper Once a yearDamper Once a year
Part Timing Check point
Media guide
Sub platen front surface
Several times a yearMedia dust accumulationForeign objects
Damages
Timing fence (CR encoder detection slit plate)
Several times a yearMedia dust accumulationForeign objectsDamages
Rail on the CR guide frame Several times a year Foreign objects
P_REAR sensor front surface Several times a yearMedia dust accumulationForeign objectsDamages
Clean pressure rollers Several times a yearMedia dust accumulationForeign objects
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 65/68
5
Operation Instructions CS9050
Menu overview
AP-40784 - Revision 1.0 65
Chapter 5 Menu overview
Setup
To Setup menu diagram (Ready to Print)(3/3)
Flushing menu
Return Count
Roll Length menu
Roll Kind
MediaType
Effect
Flushing
Side Margin
Media Initial
Media Width
(When Media Initial menu is "Off")
MediaWidth
(When Media Initial menu is not "Off")
TakeUp
Origin
Prev. Stick
Media Cut
CR Movement
Overwrite Cnt
Overwrite Wait
Slant Check
Auto Cleaning
Ink StatusRoll Length
Head Wash
CR Maintenance
Initialization
Life Times
IP Address
Subnet Mask
Gateway
Front Interlace
Temporary
1Cnt to <5Cnt> to 999Cnt
1m to <30m> to 99m
To Setup menu diagram (Ready to Print)(2/3)
None 1
None 2
Wave 1
Wave 2
Fuzz 1
Fuzz 2
<Fine&Wave 1>
Fine&Wave 2
Fine&Wave 3
Fine&Wave 4
A-S.Fine&Wave
B-S.Fine&Wave
Origin
<On Media>
<3mm> to 25mm
Off
Top&Width
<Width>
150mm to <1,000mm> to 1,351mm
<Off>
Type 1
Off
<On>
<Off>Manual
<Data>
Machine
<1Cnt> to 9Cnt
<0.0sec> to 0.1sec to 5.0sec
Off
<On>
Off/1h/2h/3h/4h/5h/<6h>/9h/12h/18h/24h
K/C/M/Y<Off>
Roll1
Roll2
Roll3
ALL
Media Type
Except Media Type
Head
Pump
CR Motor
PF Motor
000.000.000.000 to <192.168.001.253> to
255.255.255.255
000.000.000.000 to <255.255.255.000> to
255.255.255.255
000.000.000.000 to <192.168.001.254> to
255.255.255.255
Off<On>
A
B
A
B
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 66/68
Operation Instructions CS9050
Menu overview
66 AP-40784 - Revision 1.0
To Setup menu diagram (Ready to Print)(2/3)
<Type 1> to Type 30
PF Adjust menu
Initial Print
Initial Change
Confirm Print
Micro Print
Micro Change
Print Mode
PF Adjust
Pre Heater
Platen Heater
After Heater
Standby Heating
Vacuum Fan
100mm to <250mm> to 500mm
200.0mm to <250.0mm> to 300.0mm
100mm to <250mm> to 500mm
-20pulse to <0> to 20pulse
Quality 1
Quality 2
Quality 3
Quality 4Graphics 1
<Graphics 2>
Banner 1
Banner 2
Banner 3
Banner 4
Off/<30 > to 50
Off/<30 > to 50
Off/<30 > to 50
10min. to <60min.> to 240min.
Low/<High>
A
A
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 67/68
Operation Instructions CS9050
Menu overview
AP-40784 - Revision 1.0 67
5
To Setup menu diagram (Ready to Print)(3/3)
Test Print
Adjust Print
Cleaning
Selection
Version
Sleep Mode
Nozzle Check
Mode Print
Set List
ALL Set List
PaletteConfirm
Bi-D Quality
Bi-D Normal
Economy
Normal
Strong
LittleCharge
MediaType
Effect
Flushing
Side Margin
Media Initial
Media Width
Take-up
Feed
Origin
Prev. Stick
Media Cut
CR Movement
Overwrite Cnt
Overwrite Wait
Slant Check
Auto Cleaning
Ink Status
Roll Length
Head Wash
CR Maintenance
Initialization
Life Times
IP Address
Subnet Mask
Gateway
Front Interlace
ALL On
ALL Off
Main
Controller
Set Timer
Start
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
<Off>
On
<Off>
Off
<On>
Off<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off
<On>
Off<On>
Off
<On>
Off
<On>
Off
<On>
1h/2h/3h/4h/5h/<6h>/9h/12h/18h/24h
8/11/2019 OCE CS9050 Operation Instructions Book
http://slidepdf.com/reader/full/oce-cs9050-operation-instructions-book 68/68
Operation Instructions CS9050
Menu overview
PrintStartTemperature
Pre HeaterPlaten Heater
After HeaterPF Micro Adj.Backup
Pre Heater
Platen HeaterAfter Heater
Off/30 to 50Off/30 to 50
Off/30 to 50-20pulse to 0 to 20pulse