NVR3000 InstallationTutorial

NVR3000 Installation tutorial

Sales & Marketing Department

Surveon Technology 2014

Before You Start – Network Bandwidth Check

Browser

NVR3000

Windows based PCGbE Switch

VMS Remote Client

100Mbit network, check?

Cameras

The Network bandwidth will effect the quality.Please guarantee the Network bandwidth first!Go Next Step!

Click!


Browser

NVR3000


VMS Remote Client

GbE network, check?


Click!


Browser

NVR3000


VMS Remote Client GbE network, check?


Click!


Browser

NVR3000


VMS Remote Client

100Mbit network, check?

Cameras


Click!

Before You Start – Installation Scenario

DHCP Server presented No DHCP Server

DHCP Server presented Case 1 Case 3

No DHCP Server Case 2 Case 4

Customer Field Site

Your Office / Lab

* The network bandwidth between camera and NVR is 100Mbit or higher.

* The network bandwidth between remote client and NVR is 1Gbit or higher.* The total power budget of your PoE switch is enough for all cameras.

* Please make sure you already check all the pre-condition and meet all requirements

Please click the scenario which is matched your case.

Case 1




Customer Field Site

Your Office / Lab

You have DHCP server in LAB.

Your customer has DHCP server.

8Case 1 - NVR3000

: Your LAB

: Customer site

DHCP Server

Cameras

NVR3000

Your LAB

Installation Procedure: 1. No need to pre-configure in your LAB.Notice: 1. It is highly recommended to setup the system directly at customer site.2. If you have configured the cameras in your office, please remember to delete all cameras

in NVR3000 before you go to customer sites.


9Case 1 – IP Camera

: Your LAB

: Customer site

DHCP Server

Cameras

NVR3000

Your LAB

Installation Procedure: 1. No need to pre-configure in your LAB.

Notice: 1. It is highly recommended to setup the system directly at customer site.2. Cameras will all get the IP automatically in your customer’s site.


10Case 1 – Field Site Installation

: Your LAB

: Customer site

DHCP Server

Cameras

NVR3000

Your Customer Site

Installation Procedure: 1. Bring all products to your customer site.2. Install all cameras, and power on all cameras.3. Attach the network cables to LAN1 on NVR3000 4. Set DHCP mode to NVR3000 in Installation Wizard.5. Add cameras into NVR3000.6. Done

Notice: 1. It is highly recommended to setup the system directly at customer site.2. Remember to attach the cable to LAN1 on NVR3000.3. Cameras will all get the IP automatically.4. If you have configured the cameras in your office, please remember to delete all cameras



Back to Index

Case 2




Customer Field Site

Your Office / Lab

You DO NOT have DHCP server in LAB.


12Case 2 - NVR3000

: Your LAB

: Customer site

DHCP Server

Cameras

NVR3000

Your LAB

Installation Procedure: 1. No need to pre-configure in your LAB.Notice: 1. It is highly recommended to setup the system directly at customer site.2. If you have configured the cameras in your office, please remember to delete all cameras




: Your LAB

: Customer site

DHCP Server

Cameras

NVR3000

Your LAB

Installation Procedure: 1. No need to pre-configure in your LAB.

Notice: 1. It is highly recommended to setup the system directly at customer site.2. Cameras will all get the IP automatically in your customer’s site.



: Your LAB

: Customer site

Installation Procedure: 1. Bring all products to your customer site.2. Install all cameras, and power on all cameras.3. Attach the network cables to LAN1 on NVR3000 4. Set DHCP mode to NVR3000 in Installation Wizard.5. Add cameras into NVR3000.6. Done

Notice: 1. It is highly recommended to setup the system directly at customer site.2. Remember to attach the cable to LAN1 on NVR3000.3. Cameras will all get the IP automatically.4. If you have configured the cameras in your office, please remember to delete all cameras



Back to Index

DHCP Server

CamerasNVR3000

Your Customer Site

Case - 3




Customer Field Site

Your Office / Lab


Your customer DO NOT have DHCP server.

16Case 3 – NVR3000

: Your LAB

: Customer site

DHCP Server

CamerasNVR3000

Your LAB

Installation Procedure:1. Get the field site IP list of all devices.2. Attach the network cables to LAN1 on NVR3000.3. Power on the NVR3000, run the Installation wizard.4. Configure the IP of NVR3000 in the wizard according to field site IP list.

Notice: 1. Remember to attach the cable to LAN1 on NVR3000.2. Please skip the “step8: Add Camera”, we will add camera later.



DHCP Server

Cameras NVR3000

Your LAB

Installation Procedures: 1. Get the field site IP list of all devices.2. Power on and connect all cameras to a PoE switch in your LAB.3. The PoE switch should connect with you LAB network.4. Use Surveon IP utility to find all cameras.(On Windows PC)5. Login and change the IP of all cameras according to field site IP list.6. Login NVR3000, and use the local client to add all cameras into NVR3000.

Notice: 1. Surveon IP Utility: https://www.dropbox.com/s/ih1z7wwu6pt4j41/IP%20Utility_1.3A01.20140124.zip?dl=0

2. You need a windows-based PC, installed with IE10 or before.


Windows PC + IP Utility

https://www.dropbox.com/s/ih1z7wwu6pt4j41/IP Utility_1.3A01.20140124.zip?dl=0


: Your LAB

: Customer site

CamerasNVR3000

Your Customer Site

Installation Procedure: 1. Bring all products to your customer site.2. Install all cameras, and power on all cameras.3. Done


Back to IndexNotice: 1. If possible, please keep the network independent, and being used only for the NVR and cameras.2. Make sure the network bandwidth of customer’s site is guarantee.

Private and Independent Network

Case 4




Customer Field Site

Your Office / Lab



20Case 4 – NVR3000

: Your LAB

: Customer site

DHCP Server

CamerasNVR3000

Your LAB

Installation Procedure:1. Get the field site IP list of all devices.2. Attach the network cables to LAN1 on NVR3000.3. Power on the NVR3000, run the Installation wizard.4. Configure the IP of NVR3000 in the wizard according to field site IP list.

Notice: 1. Remember to attach the cable to LAN1 on NVR3000.2. Please skip the “step8: Add Camera”, we will add cameras later.



Cameras NVR3000

Your LAB

Installation Procedures: 1. Get the field site IP list of all devices.2. Find a windows PC, and change its network configuration to 192.168.88.1/243. Connect and power on only one camera to switch.4. Use the PC to login camera, the camera IP will be 192.168.88.10/24.5. Change the IP address of cameras according to your field site IP list.6. The camera will reboot.7. Repeat 7~10 until all cameras get the correct IP.8. Add cameras into NVR3000.

Notice: 1. Surveon IP Utility: https://www.dropbox.com/s/ih1z7wwu6pt4j41/IP%20Utility_1.3A01.20140124.zip?dl=0

2. You need a windows-based PC, installed with IE10 or before.

Windows PC

You DO NOT have DHCP server in LAB. : Your LAB

: Customer site

https://www.dropbox.com/s/ih1z7wwu6pt4j41/IP Utility_1.3A01.20140124.zip?dl=0


: Your LAB

: Customer site

CamerasNVR3000

Your Customer SiteInstallation Procedure: 1. Bring all products to your customer site.2. Install all cameras, and power on all cameras.3. Done


Back to IndexNotice: 1. If possible, please keep the network independent, and being used only for the NVR and cameras.2. Make sure the network bandwidth of customer’s site is guarantee.

Private and Independent Network

Questions & Answers

23

NVR3000 InstallationTutorial

Technology

Transcript of NVR3000 InstallationTutorial