Package

Overview

Installation

1

2

3

4

Warning and Caution

■ If the product does not work properly, please contact your dealer

or the nearest service center. Never attempt to disassemble the

camera yourself. (We shall not be responsible for any problems

caused by unauthorized repair or maintenance.)

■ Keep away from liquid while in use.

■ In the use of the product, you must be strict compliance with the

electrical safety regulations of the nation and region. When the

product is mounted on wall, the device shall be firmly fixed.

■ Do not use camera beyond specified voltage range.

■ Do not drop the camera or subject it to physical shock.

■ Avoid touching the camera lens.

■ If cleaning is necessary, please use clean cloth to wipe it gently.

If the device will not be used for a long time, please cover the lens

cap to protect the device from dirt.

■ Do not aim the camera at the sun or extra bright place.

■ Do not place the camera in extremely hot, cold (the operating

temperature shall be -10˚C~45˚C), dusty or damp locations, and do

not expose it to high electromagnetic radiation.

■ To avoid heat accumulation, good ventilation is required for

operating environment.

Quick Start Guide

Network Camera

Camera

Drill template

Quick start guide CD

2 tapping screws 2 plastic plugs■ Please read this instruction carefully before using the product and

keep it for further reference.

■ All the examples and pictures used here are for reference only.

■ The contents of this manual are subject to change without notice.

5

11

6

12

13

15

14

16

1

7

2

8

3

9

4

10

STATUS LINK ALARM

ALARM

DC12V

RST

IGO

LAN

1

3

2

4

5

6

7

8

9

10

11

12

14

15

16

13

Lens

IR LED ( ON: visible)

Microphone

PIR (Passive Infrared) sensor

Power indicator

Network indicator

Alarm indicator

Light sensing

Ethernet connector & PoE

Speaker

Alarm I/G/O

Power connector

Reset or WPS

Micro SD card slot

3-axis bracket

Mounting base

● Alarm Connections:

I: Alarm input interface; O: Alarm output interface; G: Grounding

Alarm input: Connect the cables of the sensor to I and G interfaces.

Alarm output: Connect the cables of the alarm output device to O and G

interfaces.

230°

71°

360°

● Indicators

Power indicator: Green: the camera is started successfully.

Network indicator: Flashing blue: the camera is connected

to the wired network successfully.

Alarm indicator: Red: alarms are triggered.

● Reset

Press RST about 10s when the camera is powered on to

restore the default settings.

● 3-axis Bracket Adjustment

The camera can be placed on the desktop or installed on the wall.

Please make sure the wall is strong enough to withstand 3 times the

weight of the camera. The steps of wall mounting are as follows.

① Attach the drill template to the place where you want to fix the

camera. Then drill the screw holes on the wall according to the drill

template.

② Peel off the drill template and then insert the plastic plugs and

screws into the screw holes. Please leave a little clearance between

the wall and the screws.

● WPS

WPS (Wi-Fi Protected Setup): Press the WPS button on the router

and then press the RST button on the camera within 120s to quickly

connect the Wi-Fi. Pressing the RST button on the camera and then

pressing the WPS button on the router will work as well. The red

alarm indicator will flash if the Wi-Fi is connected.

Network Connection5

MENU

Camera Network Cable Network Cable

Switch

Router Computer

● Access the Camera Through the Wired Network

Device Network Search

Immediate Refresh

name

name

name

IPC

IPC

IPC

unknown

unknown

unknown

192.168.226.201

192.168.1.2

192.168.1.3

80

80

80

9008

9008

9008

255.255.

255.255.

255.255.

Modify Network Parameter

Mac Address

IP Address

Modify

CE :98 :23 :75 :35 :22

192 .168 . 226 . 201

255 . 255 . 255 . 0

192 .168 . 226 . 1

i Tip: Enter the administrator password, andthen modify the network parameters.

Total Device: 3 Local IP Address:192.168.1.4 Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS：210.21.196.6

Device Name Device Type IP Address Http Port Data Port SubnetProduct Model

About

Subnet Mask

Gateway

Restore IPC Default Configuration

③ Modify the IP address. The default IP address of this camera is

192.168.226.201. Click the information of the camera listed in the

above table to show the network information on the right hand.

Modify the IP address and gateway of the camera and make sure its

network address is in the same local network segment as the

computer’s . Please modify the IP address of your device according

to the practical situation. After modification, please enter the

password of the administrator and click “Modify” button to modify

the setting.

The default password of the administrator is “123456”.

④ Double-click the IP address listed in the IP-Tool or manually enter the

IP address in the address bar of the web browser to connect the camera.

Then follow directions to download and install the applicable plug-in.

After that, enter the user name and password in the login interface.

● Access the Camera Through Wi-Fi

The default username is admin; the default password is 123456.

① Make sure that the camera and the PC are connected via LAN.

② Find the IP-Tool from the CD and then install it in the computer.

After that, run the IP-Tool as shown below.

② Run the IP-Tool and then find the IP address of the camera.

The default IP address of this camera is 192.168.226.201. Double

click it. This will bring you to the login interface of the camera.

Enter the default username and password to log in.

③ Click “Config”→ “Network”→ “WIFI” to go to the following

interface.

① Connect the camera to the LAN through the network cable.

450043001237 A0

③ Route and connect the cables.

④ Hook the mounting base to the screws and ensure that the

camera is fixed firmly. Then adjust the angle of the bracket.

⑤ Remove the protection films of the lens and the IR LED cover.

Lens

IR LED Cover

④ Enable WIFI and click “Search” to search wireless routers.

Select the desired router, enter the key number and select encryption

type. After that, select “Obtain an IP address automatically” or

manually enter the IP address by clicking “Use the following IP

address”.

⑤ Pull the network cable out of the camera.

⑥ Run the IP-Tool and find the camera through IP address or MAC

address. Then double click it listed in the IP-Tool or enter the IP

address of the camera in the address bar of the web browser to

access the camera.

∅7.5 12.2

4.534.5

mm

Plastic plug

Screw

A: You can quickly connect Wi-Fi through WPS function (See 3

Overview--WPS for more details).

B. You can also follow the steps below to connect Wi-Fi.

Enable

Index SSID Working Mode Security Mode Channel Signal Mbps Connection

1 HUAWEI-WLAN Manage WPA2-personal 2 50 150 Unconnected

WI-FI

SSID

Security Mode

Key 1

Encryption Type

Wi-Fi Networks Search

HUAWEI-WLAN

WPA2-personal

AES