Navi 1 Navi Xt User Guide 1.06

8/11/2019 Navi 1 Navi Xt User Guide 1.06

1/33

This document is available at HTTP://WWW.FALCOM.DE/.

FALCOM NAVI-1/XT

(Bluetooth

GPS Receivers)

Users guide

Version: 1.06


2/33

NAVI-1/NAVI-XT VERSION 1.06

Contents

0 INTRODUCTION ..............................................................5

0.1 GENERAL ABOUTNAVI-1........................................................ ...................................................... 50.2 PACKAGE CONTENTS .................................................... ........................................................... ....... 6

1 SECURITY .........................................................................8

1.1 GENERAL INFORMATION......................................................... ........................................................ 81.2 RESTRICTED USE........................................................... ........................................................... ....... 81.3 CHILDREN........................................................... ........................................................... ................. 81.4 DRIVING AND SAFETY................................................... ........................................................... ....... 81.5 BATTERY SAFETY ......................................................... ........................................................... ....... 9

2 PREPARING TO USE YOUR FALCOM NAVI-1 .......10

2.1 HOW DOES THE FALCOM NAVI-1 WORK? ........................................................ ......................... 10

3 SOFTWARE INTERFACE.............................................12

3.1 NMEA OUTPUT MESSAGES..................................................... ...................................................... 12

4 TECHNICAL DESCRIPTION .......................................13

4.1 BLUETOOTH GPS RECEIVER ARCHITECTURE .................................................. ......................... 134.2 TECHNICAL SPECIFICATIONS................................................... ...................................................... 134.2.1 Electrical Characteristics ............................................................. ................................................ 134.2.2 Physical................................... ................................................................ ..................................... 154.2.3 Software............ ........................................................... .......................................................... ...... 154.2.4 Technical data............................................................... ......................................................... ...... 154.3 INTERFACES........................................................ ........................................................... ............... 164.3.1 On/Off button .............................................................. .......................................................... ...... 164.3.2 LEDs..................................................... ........................................................... ........................... 164.3.3 Power jack .................................................... ........................................................... .................... 164.3.4 Interface for an external antenna................................................................................... ............... 164.3.5 Charging & Discharging the included battery .......................................................... ................... 17

5 OPERATION GUIDE......................................................19

5.1 INSTALLATION INSTRUCTIONS .......................................................... ............................................ 195.2 PC/LAPTOP ANDNAVI-1 BLUETOOTH CONNECTION ......................................................... ..... 205.2.1 How to evaluate the NAVI-1 connected to PC/Laptop......................... ....................................... 245.3 POCKED PCS BLUETOOTH CONNECTION ......................................................... ......................... 285.3.1 Using the Bluetooth GPS Receiver.............................................................. ............................ 31

6 TROUBLESHOOTING...................................................32

7 HOUSING .........................................................................33

This confidential document is the property of FALCOM GmbH and may not be copied or circulated without permission.

Page 2


3/33


Version history:

Version number Author Change

1.00 Fadil Beqiri Initial version

1.01 Fadil Beqiri Chapter 0.2 Package contents updated.The GPS indicator updated

1.02 Fadil Beqiri Chapter 0.2 Package contents updated (the ordername of AC/DC power adapter changed).

1.03 Fadil Beqiri Indicator LEDof internal battery updated.Bluetooth connection updated (pairingadded)In the Chapter 5.3,item 7 updated

1.04 Fadil Beqiri New accessories POWER-SETE(A) for

NAVI-1 are now available upon request.Sections 1.5, 4.2.3 and 4.3.5 with its sub-sections added.In the section 5.2.1,the sub-point 3)(v)added.

1.05 Fadil Beqiri Chapter 0.2 updated. New device (namedNAVI-XT) is available upon request.Chapters 4.3.5and 5.1 updated.The user guide applies to the NAVI-1 and

NAVI-XT.

1.06 Fadil Beqiri Due to the added features of NAVI-XTequipment the chapters 0.2, 4.3.5 and 5.1

updated.


Page 3


4/33


Cautions

Information furnished herein by FALCOM are accurate and reliable.However, no responsibility is assumed for its use.Please, read carefully the safety precautions.If you have any technical questions regarding this document or the

product described in it, please contact your vendor.General information about FALCOM and its range of products areavailable at the following Internet address: http://www.falcom.de/

Trademarks

Some mentioned products are registered trademarks of their respectivecompanies.

Copyright

The NAVI-1 users guide is copyrighted by FALCOM GmbH with allrights reserved. No part of this user guide may be produced in any formwithout the prior written permission of FALCOM GmbH.

FALCOM GmbH.

No patent liability is assumed with respect to the use of the informationcontained herein.


Page 4
http://www.falcom.de/http://www.falcom.de/


5/33


0 Introduction

0.1 General about NAVI-1

Dear customer, we are pleased that you have decided to purchase anintelligent navigation device such as the Falcom NAVI-1. In order quicklyto start and immediately and comprehensive to use all functions of Falcom

NAVI-1 on your utilization, we recommend you to take yourself a fewminutes to read the following references and suggestions for using your newnavigation device.The NAVI-1 is a new GPS receiver, integrated with Bluetoothtechnology. With its ultra-low power consumption, it is an outstandingquality and performance as well an excellent navigational and positioningaid tool when used with a GPS Mapping software installed on Bluetooth-

enabled devices, such as PC, laptop, or Pocked PC.The FALCOM NAVI-1 has an integrated temperature compensated crystaloscillators (TCXO). Due to the higher stability of frequency it offers a high-improved performance. Additionally, the integrated TCXO accepts thecondition for use the SiRFXTrac firmware. The FALCOM NAVI-1 usesSiRFXTrac firmware that makes it possible to track the GPS signals at farlower signal levels than is currently possible with competitive autonomousGPS solutions. Therefore, you have a high-capacity navigation system,which connects your Bluetooth-enabled device with the performance ofan intelligent and dynamic destination guidance. The embedded Class 2Bluetooth transceiver is capable of communicating with any Serial PortProfile Bluetooth device, within a 10m radius. The FALCOM NAVI-1 incommunication with your installed GPS Mapping software on theBluetooth-enabled device points you the way comfortably and reliablyfrom the current location A to your desired destination B. In this way youalso stay for longer distances always on the optimal course and arrive yourdestination point comfortable and ease. Although your receiver is fullycompatible with any GPS Mapping software running on different hardware

platforms. The embedded high-sensitivity internal GPS and Bluetoothantenna allow you to navigate freely without the hassle of messy wireconnections.

The FALCOM NAVI-1 is an equipment that can be used in a variety ofapplications including:

Navigation and positioning

Finding streets and routes

Travel planning

Safety and security

Fleet tracking and management and many others .


Page 5


6/33


0.2 Package contents

Check the contents of the package. The following items should be included.

In case of damaged or missing any item, please contact your dealerimmediately.There are two devices with the same design and software specification.Concerning the hardware specification of NAVI-XT, it comes with updatedversion of the Bluetooth chipset and new features added. However, both

NAVI-1 and NAVI-XT communicate with Host Platform via Bluetooth(Class 2) Serial Port Profile. For more information see updated chapters4.3.5and 5.1.

Description Quantity

FALCOM NAVI-XT 1

FAL 700/3.7 (Removable battery) 1

FALCOM NAVI-1 1

FAL 700/3.7 (Removable battery) 1


Page 6


7/33


Table and figures below show the accessories for FALCOM NAVI-1, whichare available by Falcom upon request.

POWER-SET-E FAL-ANT-3-MCX POWER-SET-A

FAL 700/3.7

Order name Description

FAL-ANT-3-MCX External active antenna with MCX plug connector

FAL 700/3.7 Lithium ion rechargeable battery

POWER-SET-E*

Wall charger with European outlet plugand Cigarette Lighter Adapter.(Output voltage: +5 V DC 5%

MAX. = 450 mA, MIN. = 150 mA)Cable extension and adapter connector for NAVI-1

POWER-SET-A*

Wall charger with American outlet plugCigarette Lighter Adapter.

(Output voltage: +5 V DC 5%MAX. = 450 mA, MIN. = 150 mA)

Cable extension and adapter connector for NAVI-1

* The accessories POWER-SET-E(-A) allow you to have anywhere accessto a power source such as: Car Cigarette Lighter. to any European or American (depend on the required POWER-

SET) socket-outlet. to any USB port on your computer.


Page 7


8/33


1 Security

This chapter contains important information for the safe and reliable use ofthe NAVI-1. Please read this chapter carefully before starting to use the

NAVI-1.

1.1 General information

The Global Positioning System uses satellite navigation, an entirely newconcept in navigation. GPS has become established in many areas, forexample, in civil aviation or deep-sea shipping.The GPS system is operated by the government of the United States ofAmerica, which also has sole responsibility for the accuracy andmaintenance of the system. The system is constantly being improved andmay entail modifications effecting the accuracy and performance of the GPS

equipment.

1.2 Restricted use

Certain restrictions on the use of the NAVI-1 may have to be observed onboard a plane, in hospitals, public places or government institutions,laboratories etc. Follow these instructions.

1.3 Children

Do not allow children to play with the NAVI-1. It is not a toy and children

could hurt themselves or others. The NAVI-1 consists of many small partswhich can come loose and could be swallowed by small children.Thoughtless handling can damage the NAVI-1.

1.4 Driving and safety

Do not place (mount) the device and the external antenna (if it is connected)on the parts which will obstruct the sight of the driver.Do not place (mount) the device and the external antenna (if it is connected)on the parts which block any safety device (such as the Airbag, pedals,accessory controls and any others) in your vehicle.

Your own personal judgment has always priority while you driving, if theuser of FALCOM NAVI-1 feels that the instructions of navigation software

place you in an unsafe area, then use your personal judgment according totraffic regulations and do not follow those instructions.The NAVI-1 is designed to be installed inside the vehicle. Do not place orinstall the NAVI-1 on the vehicle roof (outdoor).Please, do not handle the NAVI-1 while driving.Safety to traffic has always priority! Please use the FALCOM NAVI-1 onlyin such a way that you always keep control of your vehicle in all trafficconditions, especially when the vehicle is moving.


Page 8


9/33


1.5 Battery safety

Mistreating the battery may cause the battery to get hot, crack, or inflameand cause serious injury. In order to avoid any damage and extend the lifeexpectancy of battery, please follow the safety rules listed below before

using the NAVI-1 device: Do not place the battery on, in or near fires, apparatus which provide

heat, or other high-temperature locations. Do not place the battery indirect sunshine, or use or store the battery inside cars in hot weather.Doing so may cause the battery to generate heat, crack, or inflame. Usingthe battery in this manner may also result in a loss of performance.

Do not connect the positive pole and the negative pole of the battery toeach other with any metal object.

Do not pierce the battery with nails, strike the battery with a hammer,step on the battery, or otherwise subject it to strong impacts or shocks.

Do not solder onto the battery contacts.

Do not allow the battery to get wet.

Do not disassemble or modify the battery.

Immediately discontinue use of the battery if, while using, charging, orstoring the battery, the battery emits an unusual smell, feels hot, orappears abnormal in any other way.

Do not place the batteries in microwave ovens, high-pressure containers,or on induction cookware.

In case of the battery drips and the fluid gets into ones eye, do not rubthe eye. Rinse well with water and immediately look for medical care. Ifleft untreated the battery fluid could cause damage to the eye.


Page 9


10/33


2 Preparing to use your FALCOM NAVI-1

Read this manual in order to begin using your FALCOM NAVI-1 and tounderstand its operations, functions, and common features.

You must first install a GPS Mapping software (if none is installed) on yourPC, laptop, PDA, or other handheld devices.In order to have a Bluetooth connection with your Falcom NAVI-1,secure that the control device is a Bluetooth-enabled one.For more information about software installation, please refer to chaptersdescribed below.

2.1 How does the FALCOM NAVI-1 work?

The FALCOM NAVI-1 using SiRFXTrac software offers high positionaccuracy and fast Time-To-First-Fix (TTFF) than is currently possible with

other autonomous GPS solution. This means that the NAVI-1 will continueto determinate its positions or obtain an initial fix in places previously not

possible. In other word the NAVI-1 can be used in environments previouslydeemed inaccessible environments such as:

severe urban canyons, parking garages, dense foliage, multi-level freeways, under bridges and overpasses, and, in many cases, indoors. Coverage - Single Story Office Block

When the GPS receiver is initially turned on, it begins to determinate itscurrent positions, velocity and time which will be calculated from trackingthe GPS signals an extremely small level by 16 dBHz. While trying tocalculate a position fix, the receiver needs to be locked-on to at least foursatellites. In order to calculate quickly its current location, the receiver usesthe current received signals from in view satellites, simultaneously holds thestored data from its memory (SRAM).

Figure 1: Signal processing of NAVI-1


Page 10


11/33


When the required data are completely collected, then satellite signals aretracked continuously and the position is calculated from time to time. Whenthe received data from satellites is considered valid then the FALCOM

NAVI-1 is available for navigation. The validity of these data stored inSRAM is kept due to RTC keeps running from external battery and these

data may still be valid form the previous operation.As above the initial state of the NAVI-1 GPS receiver refers to the laststatus of the receiver in memory (SRAM). This primarily determines thelength of time it will take for your FALCOM NAVI-1 to obtain a GPS fix.Your position can be extremely quick fixed within 4 seconds from a "hot-start" state, and within 45 seconds from a "cold-start" state. The FALCOM

NAVI-1 stores data about where the satellites are located at any given time.The data is called almanac. Occasionally, when the FALCOM NAVI-1 has

been turned off for a long time, the almanac may get out-dated or cold sothe NAVI-1 performs a cold start. Otherwise, if the time and position areknowledge, as well the almanac data are also valid then the FALCOM

NAVI-1 performs a Hot start.The NAVI-1 uses the satellite signals to calculate its exact current location

by calculating its distance from the satellites. The position data within thereceiver is then converted into latitude and longitude coordinates which areusually provided in the geodetic datum on which the GPS is based (WGS84)and transmitted via integrated Bluetooth transceiver direct to theBluetooth-enabled device (PC, laptop or Pocked PC).


Page 11


12/33


3 Software interface

The NAVI-1 evaluation receiver is capable of outputting data in the NMEA-0183 format as defined by the National Marine Electronics Association

(NMEA), Standard for Interfacing Marine Electronic Devices, Version 3.00,January 1, 1997.

3.1 NMEA output messages

The table below shows all NMEA output messages supported by NAVI-1 aswell as a brief description of each output message.For more detailed information about the output message list, please refer tothe SiRFstarII message set specification available in sectionservice/downloads/manuals on Falcoms Website: www.falcom.de.

Option DescriptionGGA Time, position and fix type data.

GLL Latitude, longitude, UTC time of position fix and status.

GSAGPS receiver operating mode, satellites used in the position solution and DOP

values.

GSVThe number of GPS satellites in view satellite ID numbers, elevation, azimuth and

SNR values.

RMC Time, date, position, course and speed data.

VTG Course and speed information relative to the ground.

Table 1: NMEA Output Messages

Info:Please note that all supported NMEA messages of the NAVI 1 can beconfigured via the SiRFdemo software (See chapter 5.2.1). All userdefined settings are kept into the SRAM memory as long as theinternal rechargeable battery is connected.


Page 12
http://www.falcom.de/http://www.falcom.de/


13/33


4 Technical Description

4.1 Bluetooth GPS Receiver architecture

The NAVI-1 OEM GPS receiver from FALCOM is a new OEM GPSreceiver product that features the SiRFstarII-Low Power chipset. Thiscomplete 12 channel, WAAS-enabled GPS receiver provides a vastlysuperior position accuracy performance in a much smaller package. TheSiRFstarII architecture builds on the high-performance SiRFstarI core,adding an acquisition accelerator, differential GPS processor, multipathmitigation hardware and satellite-tracking engine. The NAVI-1 deliversmajor advancements in GPS performance, accuracy, integration, computing

power and flexibility. The delivered data from GPS receiver will sent viaBluetooth antenna to the control device (connected Bluetooth device).

Figure 2: The architecture of NAVI-1 Bluetooth GPS receiver

4.2 Technical specifications

4.2.1 Electrical Characteristics

4.2.1.1 General

Frequency L1, 1575.42 MHzC/A code 1.023 MHz chip rateChannels 12

4.2.1.2 Accuracy

Position 10 meters CEP without SAVelocity 0.1 meters/second, without SATime 1 microsecond synchronized to GPS time


Page 13


14/33


4.2.1.3 DGPS Accuracy

Position 1 to 5 meters, typicalVelocity 0.05 meters/second, typical

4.2.1.4 Datum

WGS-84

4.2.1.5 Time to First Position

Hot start < 4 sec., averageWarm start < 35 sec., averageCold start < 45 sec., average

4.2.1.6 Sensitivity *

Tracking 16 dBHzHot Start 23 dBHzWarm Start 28 dBHzCold Start 32 dBHz

* The sensitivity value is specified at the correlator. On a NAVI-1 Evaluation Receiverusing SiRFXTrac firmware with the supplied antenna, 32 dBHz is equivalent to -142dBm or -172 dBW.

4.2.1.7 Dynamic Conditions

Altitude 18,000 meters (60,000 feet) max.

Velocity < 515 meters/second (1000 knots) max.Acceleration 4 g, max.Jerk 20 meters/second, max.

4.2.1.8 DC Power

Power Built-in rechargeable Lithium-Ion batterywith +5V DC input charging circuit (700mA).

Operating time Default: 5-6 hours after full charge.

4.2.1.9 Bluetooth Serial Port

Connection : Communicate with Host Platform viaBluetooth (Class 2) Serial Port Profile.

Protocol messages: SiRF binary position, velocity, altitude,status and control.

NMEA, Msg.: GGA, GLL, GSA, GSV,RMC and VTG

Serial port settings: Baud Rate: up to 115200 bps (defaultsetting 38400 bps)

Data bits: 8

Parity: NOStop bit: 1Flow control: NO


Page 14


15/33


4.2.2 Physical

dimensions: 85 mm x 59 mm x 25 mm (L x B x H)

weight: 70 gr.

4.2.3 Software

Software Update: A firmware update is not possible on theNAVI-1 because the XTrac firmware doesnot support any function to set the Boot-pinof GPS receiver to HIGH via software.

4.2.4 Technical data

Bluetooth range: 10 m

Battery: Lithium-Ion 700 mAh/3.7V

Temperature limits

Charging temperature: 0 ~ +45Operation

Discharging temperature: 0 ~ +60C

Transportation -20 to +70 C

1 month ( 20 ~ +60)

3 month ( 20 ~ +45)Storage

1 year ( 20 ~ +25)

C

Table 4: Temperature range

4.2.4.1 TCXO-Specification

Typical phase noise density 1 Hz offset -57.0 dBc/HzTypical phase noise density 10 Hz offset -88.0 dBc/HzTypical phase noise density 100 Hz offset -112.0 dBc/HzTypical phase noise density 1 kHz offset -130.0 dBc/HzTypical phase noise density 10 kHz offset -140.0 dBc/HzLoad sensitivity 10% load change 0.2 ppmLong term stability Frequency drift over 1 year 0.5 to 2.0 ppm


Page 15


16/33


4.3 Interfaces

4.3.1 On/Off button

To turn on the NAVI-1, press the On/Off button for circa 2 seconds. In orderto turn it off again, press the On/Off button for approx. 2 seconds. Thereby,a short acoustic signal (peep) will be generated each time.

4.3.2 LEDs

Following status indicators are integrated on the top side of NAVI-1:

Indicators Description

Yellow (labelled GPS) indicates the state of GPS part

Red/Green (labelled BAT) indicates the state of internal battery

Blue (labelled BT) indicates the state of Bluetooth part

4.3.3 Power jack

In order to recharge the internal battery the 3,5 mm power jack allowsyou to connect either a car adapter cable (KA-NAVI-1-PS) or a power

charger (PS-003) to an DC electrical outlet. Both accessories are availableupon request (refer to chapter 0.2).

4.3.4 Interface for an external antenna

There is no active antenna included in the delivery packing, so the usershave to purchase one. For more information please contact one of ourdistributors.The order name is: FAL-ANT-3-MCX.The NAVI-1 provides a MCX-connector for an external active antenna. Anexternal antenna can be used instead of the NAVI-1s internal antenna. The

operation of internal GPS antenna will be deactivated if this one isexternally connected.


Page 16


17/33


4.3.5 Charging & Discharging the included battery

Your NAVI-1 is powered by a rechargeable battery, an alarm will warn youwhen the battery reaches the low level (< 3.6 V).Once the battery is clipped in the NAVI-1, plug one of the cable charger

(not supplied with NAVI-1, however, available upon request, see chapter0.2), into the corresponding power jack interface of NAVI-1. Plug thetransformer unit into a main AC power socket or vehicle power outlet (itdepend on the purchased cable charger, see chapter 0.2)with easy access.As far as the temperature limits is recognised, please refer to the table 4 andchapters 4.3.5.1and 4.3.5.2.The extreme temperatures have an unfavourable influence on therechargeable batteries. The capacity and life cycle of the batteries arereduced if they are kept at cold or warm places, e.g. in a closed car atsummer or winter conditions. Try always to keep the included battery atnormal temperatures between 15C and 25C. The GPS receiver with a too

cold or too warm battery does not temporarily operate sometimes, even ifthe battery is completely charged. Especially, the achievement of battery isstrongly reduced at temperatures under the freezing point.During the charging time the indicator LED (labelled BAT) on the top sideof NAVI-1 lights green (if the equipment is switched off). Charging will beterminated after the battery reached full capacity (4.2V/700 mAh) whichapproximately takes 2-3 hours. During this time the NAVI-1 can also beused, but note that, the batterys capacity has to be higher then 3.8 V.Keeping the cable charger plugged to the equipment when the battery isfully charged does not damage the battery, but it is recommended to unplugfrom the power source. To optimise battery capacity, you should allow the

battery to fully discharge every now and then. If you do not intend to useyour NAVI-1 for several days, we recommend you to disconnect it from the

battery. The NAVI-1 can also be used while it is on charge.

New feature for NAVI-XT, only

The NAVI-XT can also operate without the need of the internal battery.However, it must be always connected via one of the cable charger(available upon request, see chapter 0.2)to an external power source duringthe operation. Keep in mind the validity of GPS data stored in SRAM is nomore available if the internal battery of the NAVI-XT is removed and it is

disconnected from the external power source. That means, the NAVI-XTallways performs a cold start after each power on procedure.

4.3.5.1 Safety precautions while charging the battery

Be sure to follow the rules listed below while charging the battery. Failureto do so may cause the battery to become hot, rupture, or ignite and causeserious injury.

When charging the battery, either use one of the aforementioned batterycharger or otherwise insure that the battery charging conditions specified

by Falcom are met. Do not attach the NAVI-1 to a power supply plug or directly to a cars

cigarette lighter (an adapter cable has to be used).


Page 17


18/33


Do not place the NAVI-1 into direct sunlight. When the battery becomeshot, the built-in safety equipment is activated, preventing the batteryfrom charging further, and heating the battery can destroy the safetyequipment and can cause additional heating, breaking, or ignition of the

battery.

The temperature range over which the battery can be charged is 0C to45C. Charging the battery at temperatures outside of this range maycause the battery to become hot or to break. Charging the battery outsideof this temperature range may also harm the performance of the batteryor reduce the batterys life expectancy.

4.3.5.2 Safety precautions while discharging the battery

Do not discharge the battery using any other device except for the FalcomNAVI-1. The temperature range over which the battery can be discharged is-20C to 60C. Use of the battery outside of this temperature range may

damage the performance of the battery or may reduce its life expectancy.


Page 18


19/33


5 Operation Guide

Before using the NAVI-1, make sure to prepare the following items:

GPS software is properly installed on your Bluetooth-enableddevice (PC, laptop, Pocked PC, or other handheld devices).

The Bluetooth GPS Receiver is fully powered (i.e. internalbattery is full charged) and operational.

Check that the Bluetooth GPS Receiver is ON.

This section will outline the necessary procedures for the Bluetooth GPSreceiver to run smoothly with the GPS Mapping software.

5.1 Installation instructions

In the delivery package the FAL 700/3.7 battery for NAVI-1 is separatelypacked, just take it out from its package, open the cover cap on theunderside of the NAVI-1 and insert the FAL 700/3.7 in it. The four contact

pads of the NAVI-1 and battery have to be in the same direction andopposite to each other, finally close the cover cap. In order to recharge the

battery one of the aforementioned adapters has to be used. Place yourFalcom NAVI-1 in a location (e.g. vehicles dashboard) and turn it on by

pressing for approx. two seconds the On/Off button. In order to turn it offagain, press for approx. 2 seconds the same button. Thereby, a short acousticsignal (peep) will each time be generated.The position of the NAVI-1 mounting is crucial for its optimal performance.

Place the NAVI-1 in a way that the receiving side of the internal GPSantenna which is placed on the top of NAVI-1 to have direct view to the skyThe Bluetooth connection between the Falcom NAVI-1 receiver and yourmobile phone/PDA/PC or laptop has to be established.

The following information will be indicated via 3 corresponded LEDs onthe top side of NAVI-1.

1. Left LED (blue), Bluetooth optical indicator:

Blinking, the equipment is ready for a Bluetooth connection.

Continually light, the connection between devices is created andready for use.

2. Middle LED (red/green), State of charge optical indicator:Continually red, the equipment is switched on and the internal

battery is fully charged.Blinking red, the voltage of internal battery is under 3.5 V, youhave to recharge it.Continually green, the internal battery is in charging phase and theequipment is switched off.Green off (connected to power charger), the internal battery now iscompletely charged.

3. Right LED (yellow), GPS optical indicator:

Blinking, the GPS-Mouse is searching for satellites

Continually light, the valid GPS data are being received.


Page 19


20/33


The following information will be indicated via 3 corresponded LEDs onthe top side of NAVI-XT:

1. Left LED (blue), Bluetooth optical indicator:

Blinking, the equipment is ready for a Bluetooth connection.

NOTE: The NAVI-XT will be turned off without any warning, if abluetooth connection between the NAVI-XT and the hostdevice is not made within 20 minutes after the NAVI-XTis turned on (it is a feature of power saving). If the deviceis turned off, to turn the NAVI-XT on again, press theON/OF button (see chapter 4.3.1)

Continually light, the connection between devices is created andready for use.

2. Middle LED (red/green), State of charge optical indicator:

Blinking red, the voltage of internal battery is under 3.5 V, youhave to recharge it.

Continually green, the internal battery is in charging phase and theequipment is switched off.Green off (connected to power charger), the internal battery now iscompletely charged.This LED is turned off, if the equipment is switched on and theinternal battery is fully charged (power saving feature).

3. Right LED (yellow), GPS optical indicator:

Blinking, the NAVI-XT is searching for satellitesContinually light, the valid GPS data are being received.

Please, refer to the corresponding chapter as far as the Bluetoothconnection is concerned.

5.2 PC/Laptop and NAVI-1 Bluetooth Connection

To set up a connection between PC (in this case running Windows 2000,WIDCOM Bluetooth software Rev. 1.4.1 as well as a TyphoonBluetooth USB adapter) and the NAVI-1, please follow step by step theinstructions below.1. If the Bluetooth software is not installed in your control device yet,

please install it, plug your Bluetooth USB adapter into one of the USBfree COM port before you begin the next steps.

2. If your NAVI-1 is turned off, please turn it on. Once the Bluetoothreceiver is turned on, the internal LED will appear as shown:


Page 20


21/33


Blue LED flashes every one second (the Bluetooth is on, and readyfor connection).

3. Activate Bluetooth on your PC. Open the Bluetooth installdirectory and double-click on its icon. If the Bluetooth icon on the

bottom right-hand corner of the PC screen is blue-red, you will need to

activate Bluetooth. Click on the icon, and a pop-up menu will appearin the display. Select Enable Bluetooth Ratio. The colour of theBluetooth icon will be changed from blue-red to blue-white,signifying that it is turned on. As shown in figures below:

4. Click Start button, point to Settings, Control Panel and click theBluetooth configuration, a screen will appear in the display. Select

the Hardwarepage and check if your USB Bluetooth device is foundand it works properly, as shown below.

5. Close appearing screen. Search for the FALCOM NAVI-1. Rightmouse click the Bluetooth icon on the bottom right-hand corner of thePC screen. On the next pop-up that appears, select Explore My

Bluetooth Placesitem.

Double-click on the marked icon to find the Bluetooth devices in theBluetooth neighbourhood.


Page 21


22/33


6. After a few seconds, a list of Bluetooth devices will appear on yourscreen. You will see the FALCOM NAVI-1 appear in the ServiceSelection. Select the FALCOM NAVI-1 icon. In order to discover theservices offered the FALCOM NAVI-1 click the link click here on the

left side of opened window.

7. The service appears below allows the users to establish a virtual serialport. Right-click on the ... FALCOM NAVI-1 icon, on the appearingpopup menu click the Connect to Bluetooth Serial Port item. TheLED blue light constantly (means Bluetooth connection is created).Secure Connection:

As far as the Secure Connection for NAVI-1 is concerned there is no

security entered i.e. there is no device pairing required if the SecureConnection option is disabled for a Bluetooth service or application.Please check the software configuration to disable the SecureConnection (e.g. go to Start>Settings>Control Panel and click theBluetooth configuration, a Bluetooth configuration screen willappear in the display. Select the Client Application tab, then double-click on the Application Name Bluetooth Serial Port anddeactivate its Security Connection on the next appeared dialog box).In order to pair two devices with each-other the Secure Connectionoption has to be enabled for a Bluetooth service or application (e.g. goto aforementioned directory and activate its Security Connection). After

inquiry process, the pairing process needs a valid PIN which for NAVI-1is 1111 pre-defined.


Page 22


23/33


For more details about Bluetooth, please refer to the software manualthat you are currently using.

8. The aforementioned icon will change its colour from grey to green asshows in the figure below. The service which the NAVI-1 offers is alsoshown below.

9. In order to see the signal strength of Bluetooth connection, right-clickon its icon, on the next appeared pop-up menu select the Status item.The signal strength is at the bottom of the appeared screen indicated. Tryexperimenting with your Bluetooth GPS receiver to see how far itneeds to be before the blue bar reaches. If the user right-clicks the iconagain and selects the Propertiesitem an available COM Port is selected.


Page 23


24/33


5.2.1 How to evaluate the NAVI-1 connected to PC/Laptop

After the Bluetooth connection is established, please download theSiRFdemo software which is free available on Falcoms Website:

www.falcom.de>downloads>SiRF>SiRFdemo.zip1) Run the SiRFdemo software by double clicking the SiRFdemo.exe file.

The SiRFdemo program will be automatically installed onto yourcomputer.

2) To start the SiRFdemo software, either double-click on theSiRFdemo.exe installed file or if you have created a shortcut on yourdesktop, double-click the SiRFdemo.exe.

3) The SiRFdemo software will be appeared as follow:(i) Before running the software, make sure that your PC isrecognizing the NAVI-1 properlyOn the activated Data Source Setup window, select the COM(e.g. COM9) for SiRFdemo program and set the baud rate e.g. to4800 bps. See figure below:


Page 24


25/33


(ii) Click the icon on toolbar by the up-down button (marked buttonin figure below) the program will automatically detect theselected COM port and starts evaluating.


Page 25


26/33


(iii)The output messages can be displayed in the Development Datascreen. For a description of NMEA messages please downloadfrom Falcoms Website the SiRFmessages.pdf file. Thevalid/invalid protocols can be recognized on the $GPRMC

protocol as shown in figure below. The capital letter A means,incoming protocols are valid and the capital letter V means,incoming protocols are invalid.


Page 26


27/33


(iv) If the NAVI-1 is receiving valid GPS positions, click the icon ontoolbar by the up-down button (see marked button in figure

below), the user can see the updated data of longitude, latitude,altitude, date time etc. For more detailed information about the

using of SiRFdemo software, please download the SiRFdemo.pdfmanual, which is also available on our web page.

(v) In order to set the desired update rate of the supported NMEAprotocols, click the Actionmenu on the Main Menu, then selectthe item Switch to the NMEA Protocol . The dialog box

below will appear. Now select the required update rate in thecorresponding box of protocol and click the Send button. Theresult will be displayed on the Development Data screen.


Page 27


28/33


5.3 Pocked PCs Bluetooth Connection

In order to set up a connection between your Pocket PCs and the NAVI-1,please, follow step by step the instructions below.

HINT: Perform a Bluetooth device discovery on your Pocked PCs tofind the Bluetooth GPS Receiver. Refer to the userdocumentation of your Bluetooth device for instructions, too.

1. If the Bluetooth software is not installed in your Pocked PCs yet,please, install it before you begin the next steps.

2. If the internal battery is not full charged, connect your NAVI-1 to theaforementioned power supply via one of the aforementioned adapters.When the charge procedure has been completed (refer to the batteryindicator and its description) then turn the NAVI-1 on by pressingapprox. 2 sec. the On/Off button. Once the Bluetooth receiver isswitched on, the LEDs will appear as shown:

The GPS indicator blinking every one-second (i.e. the GPS receiveris searching for satellites), no GPS fix is obtained.Note:For best results, you should also perform a GPS fix now. The

GPS indicator will light steadilywhen a GPS fix is performed.If there is trouble during acquire a GPS fix, replace the location of

NAVI-1 or switch it off and on again.

The battery indicator permanently green (i.e. battery full charged)

The Bluetooth indicator flashes every one second (the Bluetoothis on, and ready to establish a Bluetooth connection)

3. First, you must turn on the enabled Bluetooth device (in our exampleiPAQ 38xx Bluetooth device). Check the Blue Manager's icon on theright-bottom screen. If the icon is grey i.e. the Bluetooth is turned off.In order to turn the Bluetooth on, tab on the Bluetooth icon onright-down corner of your Pocked PCs device display, a pop-up menuwill appear. Select Enable Bluetooth Ratio. The colour of theBluetooth icon will be changed from grey to blue-white (it depend onthe installed Bluetooth software), signifying that it is turned on.


Page 28


29/33


4. Search for the FALCOM NAVI-1. Open the Bluetooth popup menuon the right-bottom screen. Tab on the Bluetooth Manager.

5. If you have not searched for devices since last search, tap Search menuat bottom (below right). After search is completed, a list of foundBluetooth devices will appear on your screen. Check the FALCOMNAVI-1 found (below left) and tap Save. Then tab OK on the following(below right) screen.

6. You will be returned to the Bluetooth Manager screen. Tab the

FALCOM NAVI-1 icon to get the device information.


Page 29


30/33


7. Tap on Actions menu and "Connect to GPS_NMEA .." (below left).This will take a short time to be completed (below right). Now tap OKto return to Devices list.

8. Your last step is to find which serial port is connected to. At the mainBluetooth Manager screen, tap Tools Menu and "Settings for AllDevices" (below left).On the Settings screen, tap "Serial Port" tab. Note the entry for"Outbound Com Port" (COM8 in screenshot below right) and InboundCom Port (COM7 in screenshot below right).As far as the Secure Connection for NAVI-1 is concerned, please, referto the chapter 5.2 (click here). If the option Passkey is required isselected, see figure right below, then enter 1111 when asked for a

passkey for the device.For more details about Bluetooth, please refer to the software manual

that you currently use.


Page 30


31/33


When the FALCOM NAVI-1 Bluetooth GPS receiver is connected tohandheld device, the Bluetooth indicator on the NAVI-1 BluetoothGPS receiver will be steadily on.

5.3.1 Using the Bluetooth GPS Receiver

As soon as you have installed and configured the Falcom NAVI-1 on yourmobile equipment (Pocked PCs), the inserting of navigation is anymore inthe way. You have just to run the installed GPS Mapping software. TheBluetooth connection for the installed GPS Mapping software must be setto the correct COM port (please refer to the user documentation of theinstalled GPS Mapping software for instructions). Determine which COM

port number your Bluetooth device uses for serial COM port connections(in our example is COM 7). The FALCOM NAVI-1 communicates to a

Bluetooth serial port with following settings: up to 115200 bps, 8 DataBits, NONE parity, 1 Stop Bit. Depending on the device you use forBluetooth connectivity, you may or may not need to modify the COM

port setting. If necessary, refer to the user documentation of yourBluetooth device. In order to navigate to your destination, please, refer tothe user documentation of installed GPS Mapping software for instructions.There you will find exactly explained the methods for setting the destinationand following the navigation instructions to travel to your destination.We wish you much fun and have a good trip with your FALCOM NAVI-1.

!!Please remember that:Safety to traffic has always priority! Please use the FALCOM NAVI-1 onlyin such a way that you always keep control of your vehicle in all trafficconditions.


Page 31


32/33


6 Troubleshooting

Q: The installed software does not seem to establish any connections

with NAVI-1. How do I make it work?

A: Make sure that your Pocked PC has found the "FALCOM NAVI-1"Bluetooth device. Follow the instructions in the Connection sectionto make sure that your Pocked PC has recognized the Bluetooth GPSreceiver properly. If so, you will need to connect with the device bygoing to the Bluetooth Manager and tab on the on Actionsbutton andthen "Connect to GPS_NMEA ..".

Q: I have established a blutooth connection but the NAVI-1 does not

seem to have any GPS fix, what should I do?

A: Shutdown the FALCOM NAVI-1 and turn it on again. Change thelocation of NAVI-1 (maybe poor signals are received), but inaccordance with the capability of Bluetooth communication.

Q: The FALCOM NAVI-1 seems to have a GPS fix (GPS indicator issteadily light), but unable to establish a connection between the

NAVI-1 and my Pocked PC. How can I perform a connection?

A: Go to the Bluetooth ManagerAll devices on your Pocked PC. TapActionsmenu and then "Remove this Device".

Next, shutdown your FALCOM NAVI-1 by pressing the On/Off buttonapprox. 2 second. Then perform a soft reset on your Pocked PC.Once your Pocked PC has finished resetting itself, go back to theBluetooth Manager screen and perform the typical setup andconnection procedures for your Bluetooth receiver (for help withconnection, please review the Connection section).Finally, run the installed GPS Mapping software, select the assignedCOM Port from Bluetooth connectivity, set the baud rate up to115200 bps (you may or may not need to modify the COM port setting,it depend on your using Bluetooth device), and click Open Port. Thecurrent position will appear on the GPS Mapping software.


Page 32


33/33


7 Housing

A

B

C

D

E

F

G

1 2 3 4 5 6 7 8

A

B

C

D

E

F

H

G

1 2 3 4 5 6 7 8 9 10 11

Savetydue to DIN 34 DIN 16 901

class:Tolerance

Date Name

created

checked

std check

Colour

Material Surface

Name

Dwg No.

file Sheet1/1

130

Version

CL-No.

Scale

Dimensions

inmm Weight

RAL

VDI 3400ref.

01972501.slddrw

mold tech

1 : 1

PANTONE

g

mm^3

GPS-BT-Mouse FPKonzept

Volume xxx

xxx

Arend10.09.03

Project

xxx

FlamebilityUL94

0197 25 01xxxGPS BTMouse

12

A

E

E-E (2 :1)

85.3

0mm

58.80 mm 25.10 mm

Navi 1 Navi Xt User Guide 1.06

Documents

Transcript of Navi 1 Navi Xt User Guide 1.06