Mobile workshop solution sample

download Mobile workshop solution sample

of 12

  • date post

    17-Jul-2015
  • Category

    Automotive

  • view

    38
  • download

    0

Embed Size (px)

Transcript of Mobile workshop solution sample

  • 1

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    MOBILE WORKSHOP SOLUTION CONTAINER BASED

    By:

    Bahrain, Juffair 27th December 2013

    INCLUDED IN:

    20 container conversion in to a Mobile Workshop Solution

    a. Isolated 20 foot steel container with TwistLocks b. Wing double doors at back side c. Single side doors at the right side d. Air Condition 220V e. Ladder rack with Aluminium ladder 13m f. Mono rail crane 1000 kg g. Trail Blazer (all in one: generator 13kW, air compressor, welding and jump starter/battery

    charger h. High pressure hot water washer i. Trolley EasyClick with drawers for service tools j. Workbench with drawers and spare part top compartment with boxes and vice 140mm. k. Work office table with chair and additional shelves and drawer l. Rack for spare tires 12pcs. m. Shelves and slide outs for spare parts n. ALU ramps for loading and unloading o. Jack Trolley p. Acetylen and Oxygen trolley q. Space for two Oil barrels with lashing rails and lashing belts r. Two foldable beds with special mattress L+R s. Hose and cable holders t. 220V lights with NEON lamps u. 12V Emergency lights-connected to Trail Blazer battery

  • 2

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    v. First aid kit in case w. Fire extinguisher 3x x. Wall hanged cases with small colored boxes for small material 4x y. Perforated ALU wall panels for quick tools and material

    INSULATED DRY BODY CONTAINER

    -External Dimensions: L 6058 x W 2438 x H 2591mm -20 foot new container (fitted with corner blocks and fork pockets) -One man door on side, steel / insulated -Container existing plywood floor finished with 3mm thick aluminium checkered plate -Internal wall and ceiling insulated with 60mm sandwich panel, one side aluminium foil and Finish -side 2mm steel plate powder coated sheet (exterior of the container is 1.6mm corrugated panel), joints are covered with aluminium profiles. -Installed monorail of 250mm high with sliding mechanism as shown below -Recessed power supply box, power sockets with changeover switch, as shown below in Sample (Picture 3) -Recessed condenser space on top left corner -Steel step ladder, sliding into container floor -Exterior painted with color of your choice -Supply and install 24000BTU split Air conditioner -Roof will be specially reinforced for sliding rail -1x aluminium folding ladder rack with ALU ladder 13m on top of the container -1x electrical distribution box with 6 breakers (3x 15 Amp + 3x 10 Amp) -2x electrical 3pin socket (one inside and one outside) -1x float switch as exchanger (outsourcing or/to inner generator) -Body of the container will be colored to your company color -1x Split air conditioner for the container 220V on the roof -One year warranty for any kind of manufacturing defects of the body. However the warranty will not cover defects due to mishandling. Sample picture of container

  • 3

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    Technical Drawings of container:

  • 4

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

  • 5

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    Conception drawings of Mobile Workshop Solution

  • 6

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

  • 7

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

  • 8

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

  • 9

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

  • 10

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    Trailblazer 302 Air Pak The all-in-one tool that delivers multiprocess output for welding, plasma cutting, gouging, air tools, and12/24-volt battery charger/jump starter.

    Welder/generator/air compressor/battery charger is warranted for 3 years, parts and labor. Engine is warranted separately by the engine manufacturer.

    Trailblazer 302 Air Pak Features Size and Weight Takes only half the bed space of a separate engine-driven air compressor and welder, freeing up to 50 % more room on your truck for equipment and supplies. Plus decreases axle weight up to 25 %. Independent Weld and Generator Advantages 13,000 watts of voltage-regulated power No interaction between grinders, power tools, etc. and the welding arc Generator power is independent of weld Four-pole weld generator produces the best arc quality

    Output Range Welding DC Stick 25 300 A DC TIG 10 300 A AC TIG/Stick 10 225 A MIG/FCAW 13 35 V, 350 A

    Generator Power Output Rated at 104 F (40 C) Peak: 13,000 W Continuous: 11,000 W

    Industrial Rotary-Screw Air Compressor Runs most air impact wrenches at idle Produces 31 CFM of air at 100 percent duty cycle Delivers 80 160 PSI of air with no storage tank Gives 100 percent deliverable air Compressor is warranted by Miller for three years

    Battery Charger/Jump Starter Provides selectable 12- or 24-volt battery charging capability Provides up to 450 amps of battery jump-starting capability Convenient front panel battery charger/jump starter access 25-foot battery jumper cables available (#300 422)

  • 11

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    AR Blue 1550 Washer

    Hot water high pressure washer MAX pressure 110bar/1600psi Flow rate 370lt/h Power input 1.8kW Supply 230V / 50Hz / 1ph RPM 2800 Weight 44kg Outer dimensions: 40 x 61 x 94 (L x W x H) cm

    Additional accessories for compressor

    Inflating gun with gauge and aluminium body with PVC hose 30 cm long Aluminium blowing gun TCS-210NR Air Hose reel with 10 meter hose Air high pressure hose 50m Impact wrench Jacking trolley - Hand pallet truck

    Details MITSHUBISHI MBF 25 Ergonomic rubber handle offers comfort, safety and high productivity Compact design combined with a 210-degree steering angle gives maximum manoeuvrability Sturdy fork design with welded construction gives extra strength and durability 2500 kg capacity Weight 65 kg

  • 12

    H&H Villa, Building 417 | Road 41 | Al Shabab Avenue | Block 340 | Juffair, Manama | Kingdom of Bahrain

    Aluminium Ladder Rope operated extension ladder

    Ergonomic Specifically for heavy duty use within tough and rigorous environments These ladders are produced to BS2037 Class 1. With a Class 1 Rating, the highest ladder rating available These ladder will safely support a maximum static load of 175kg Fitted with rope operation, these ladders can be easily extended with a smooth operation and minimum amount of effort The heavy duty round rungs are securely fitted into the ladder stiles and offer a safe and secure Foothold