20-06983-00 Rev. G © Hydro Systems Company, Inc. 2012 HydroSystemsCo.com Toll Free: 1.800.543.7184 1

Installation Reference: Wall Mount

Meteor™ Dish Machine Dispenser

!WARNING:Do not exceed 140° water temperature.

ADVERTENCIA: La temperatura del agua no debe sobrepasar 140°F / 60°C

Installation Reference: Top Mount

Wall Anchors

Mounting Screws

Inlet Tube (not supplied)

Bowl Assembly

Tie Wraps

PVC Tube

Bulkhead Fitting

Rubber Washer

7/8” Hole (back of machine)

Plastic Washer

Nut

Water Level

Water Level

Inlet Tube (not supplied)

Bowl Assembly

Rubber WasherPlastic WasherNut

7/8" Hole (top of machine)

Reference View

Note: To prevent rotation of the bowl, drill a hole in this location and secure with a stainless sheet metal screw.

20-06983-00 Rev. G © Hydro Systems Company, Inc. 2012 HydroSystemsCo.com Toll Free: 1.800.543.7184 2

Replacement Parts Listing

Vacuum Breaker Valve, Plastic1/4” Fittings01-06971-00

Vacuum Breaker Valve, Metal1/4” Fittings01-06971-01

Spray Tube27-06909-00

Arm / Retainer, Kit15-07015-00

Arm / Retainer, Kit15-07015-00

Nozzle(see assortment in Accessory Kit)

Bowl(not sold separately)

50 Deg. OC Nozzle, Kit (4 PK)15-07011-52- - -70 Deg. OC Nozzle, Kit (4 PK)15-07012-72- - -90 Deg. OC Nozzle, Kit (4 PK)15-07013-92- - -90 Deg. OC Nozzle, Kit (4 PK)15-07013-94

Accessory Kit15-06968-00

Hose41-06985-00

20-06983-00 Rev. G © Hydro Systems Company, Inc. 2012 HydroSystemsCo.com Toll Free: 1.800.543.7184 3

Nozzle Selection and Replacement

Suggested Nozzle Application Guide-94 OC (Black): Encapsulated powder (use screen cap)-92 OC (Lt. Gray): Encapsulated powder (use screen cap) or solid (use

open mouth capsule), high feed rate-72 OC (Lt. Blue): Encapsulated solid (use open mouth capsule)-52 OC (Red): “Tall Bottle” solid (use open mouth)

Nozzle Replacement (Detailed Instructions on Page 4)1. Turn off electrical power and water supply.2. Depress retaining arm and remove screen.3. Continue to depress retaining arm (or remove metal safety spring)

to access nozzle.4. With 3/8" socket driver or nut driver, remove and reinstall nozzles.

Do not overtighten.5. (If removed, replace safety spring) and snap screen firmly in place.

Retaining ArmNozzle(Metal safety spring retracted)

Screen

20-06983-00 Rev. G © Hydro Systems Company, Inc. 2012 HydroSystemsCo.com Toll Free: 1.800.543.7184 4

1. TURN OFF ELECTRICALPOWER AND WATERSUPPLY (while metalsafety spring is stillcovering nozzle).

2. Depress retaining arm toretract metal safetyspring.Use hook tool to detachand remove screen.

3. Insert hook tool nearsafety spring andbegin lifting screen.

4. Continue lifting screenat each rib locationuntil screen is no longersnapped under ribs.

5. Slide screen off ofsafety spring and setscreen aside.

6. Continue to depressretaining arm to accessnozzle (or removemetal safety spring).

7. Use 3/8”socket driver(or nut driver)to removeold nozzle.

8. Lift out old nozzle andscrew in new nozzle.Use 3/8” socket driver(or nut driver) totighten new nozzle.Do not overtighten.

9. With new nozzlesecurely in place,locate slot onunderside of screen.blank line(If metal safetyspring was removed,replace it now.)

10. Using hook tool, slidescreen onto the metalsafety spring, thensnap screenunder ribs.blank lineIMPORTANT:Secure screenunder each rib bypressing firmly withfingers until screensnaps into place.

11. Release retainingarm. Metal safetyspring slides backinto place and coversnew nozzle.

12. Restore electricalpower & water supply

Nozzle Replacement