Partial Discharge Characteristics in LLDPE-Natural Rubber ...
Mechanochromic LLDPE Films Doped with NIR Reflective ...
Transcript of Mechanochromic LLDPE Films Doped with NIR Reflective ...
HAL Id: hal-03043710https://hal.archives-ouvertes.fr/hal-03043710
Submitted on 7 Dec 2020
HAL is a multi-disciplinary open accessarchive for the deposit and dissemination of sci-entific research documents, whether they are pub-lished or not. The documents may come fromteaching and research institutions in France orabroad, or from public or private research centers.
L’archive ouverte pluridisciplinaire HAL, estdestinée au dépôt et à la diffusion de documentsscientifiques de niveau recherche, publiés ou non,émanant des établissements d’enseignement et derecherche français ou étrangers, des laboratoirespublics ou privés.
Mechanochromic LLDPE Films Doped with NIRReflective Paliogen Black
Cosimo Micheletti, Pierpaolo Minei, Marco Carlotti, Virgilio Mattoli,Francesco Muniz- Miranda, Anna Perfetto, Ilaria Ciofini, Carlo Adamo,
Giacomo Ruggeri, Andrea Pucci
To cite this version:Cosimo Micheletti, Pierpaolo Minei, Marco Carlotti, Virgilio Mattoli, Francesco Muniz- Miranda,et al.. Mechanochromic LLDPE Films Doped with NIR Reflective Paliogen Black. Macromolecu-lar Rapid Communications, Wiley-VCH Verlag, 2020, pp.2000426. �10.1002/marc.202000426�. �hal-03043710�
1
Mechanochromic LLDPE Films doped with NIR
Reflective Paliogen Black
Cosimo Micheletti,1 Pierpaolo Minei,
1 Marco Carlotti,
2 Virgilio Mattoli,
2 Francesco Muniz-
Miranda,3 Anna Perfetto,
3 Ilaria Ciofini,
3 Carlo Adamo,
3,* Giacomo Ruggeri,
1 Andrea
Pucci1,*
1 Dipartimento di Chimica e Chimica Industriale, Università di Pisa, Via Giuseppe Moruzzi
13, 56124 Pisa, Italy
2 Center for Micro-BioRobotics @SSSA Istituto Italiano di Tecnologia Viale Rinaldo Piaggio
34, 56025 Pontedera, Italy
3 PSL University, École nationale supérieure de chimie de Paris, CNRS, Institute of
Chemistry for Life and Health Sciences (i-CLeHS), FRE2027, 11, rue Pierre et Marie Curie,
F-75005 Paris, France;
Corresponding author:
Prof. Andrea Pucci, Department of Chemistry and Industrial Chemistry, University of Pisa,
Via Giuseppe Moruzzi 13, 56124 Pisa, Italy. Email: [email protected]
Prof. Carlo Adamo, Institute of Chemistry for Life and Health Sciences (i-CLeHS),
FRE2027, 11, rue Pierre et Marie Curie, F-75005 Paris, France. Email:
2
Abstract
The perylene bisimide derivative Paliogen Black (P-black) has been proposed as a new
chromogenic probe which shows visible (VIS) and near-infrared (NIR) responses after
mechanical solicitations of host linear low-density polyethylene (LLDPE) films. P-black has
been reported to display strong absorption in the VIS spectrum and unusual reflective and
cooling features in the NIR region. Uniaxial deformation of the 2.5, 5 and 10 wt% P-
black/LLDPE films yields a dichroic absorption under polarized light with color variations
attributed by the computational analysis to the distinct anisotropic behavior of the transition
dipole moments of P-black chromophores. When LLDPE films are deformed, P-black
aggregates reduce their size from ∼30-40 μm to ∼5-10 μm that, in turn, causes reflectivity
losses of about 30-40% at the maximum elongation. This gives rise to warming of 5-6 °C of
the locally oriented film placed in contact with a black substrate under the illumination with
an IR lamp for 5 seconds. These features combined with the high sensitivity of the VIS-NIR
response towards mechanical solicitations render P-black as a new solution to detect uniaxial
deformations of plastic films through both optical and thermal outputs.
3
1. Introduction
Nowadays, smart materials with chromogenic features are widely employed in the detection
of external stimuli such as deformation, temperature alterations, and light exposure.[1]
Such
optical sensors are based on the predictable relationship between the presence of the relevant
stimulus and changes in the wavelength of light absorbed and/or emitted by the sensing
system. The introduction of chromogenic species into polymers in the form of dispersed or
covalently bonded chromophores have been reported as the most exciting and versatile
procedure for conferring color features that are strongly depending on the environment
variations.[2, 3]
Moreover, the possible formation of dye aggregates opens a wealth of exciting
opportunities for the development of polymers with targeted chromogenic features. Notably,
molecular aggregates can display entirely new features with respect to the isolated dye
molecules and result extremely sensitive to external solicitations thus supporting smart
materials as sensitive optical sensors.[4]
Polymers that respond to mechanical stimuli through
variations of their optical features are called mechanochromic. Mechanochromism in
polymers was reported for the first time by Weder in 2002[5]
and it has been supported by
using diverse polymeric materials and different classes of aggregachromic dyes and
fluorophores.[6-11]
Notably, the optical responses towards mechanical solicitations are
consistent with variations in the absorption and/or emission of these dye/polymer assemblies
due to modifications of their interphase interactions and chromophore orientation towards the
stress direction.[2, 3, 7, 12, 13]
Many practical applications can be predicted, e.g. mechano- and
pressure sensors,[14, 15]
indicators of mechano-history, security plastics and papers and data
storage devices.[16-20]
and new solutions are provided everyday.[21-27]
Among the different
chromogenic dyes, perylene bis-imide derivatives (PBIs) are one of the most investigated
since their optical features result strongly depending on molecular packing among the
chromophoric units.[4, 28-30]
The disaggregation phenomena of PBIs assemblies triggered by
4
polymer deformation causes a clear modification of the their optical features with very
evident changes especially in emission.[7, 31]
Dyes embedded into plastic films are also
reported to display a well-defined dichroic pattern in polarized light owing to the oriented
chromophore assemblies towards the drawing direction of the film.[8, 32]
Very recently, there has been a growing interest in the application of PBIs as Near-Infrared
(NIR) transparent and reflective organic pigments for the development of cool organic
coatings for different surfaces.[33-36]
Painting building roofs with coatings based on cool
pigments, is indeed one of the most accessible solutions to reduce the warming effect caused
by the sunlight exposure, which is mainly due to the absorption of the NIR contribution of the
solar spectrum. This approach has been recently reported to reduce the energy demand and
therefore beneficial for downgrading the urban heat island (UHI) phenomenon.[37]
One of the
most effective PBIs with NIR reflective features is Paliogen® Black L0086 (P-black, Figure 1
left panel up) that is distributed by BASF as pigment for solar heat management in paints.[38]
P-black mimics the transparent and NIR reflective features of certain green plants[39]
thanks
to the high-symmetry of PBI that favors the formation of crystalline supramolecular
assemblies promoted by the intermolecular π-π interactions among perylene nuclei.[34, 36, 40-43]
Its supramolecular structure preserved within the polymer coatings allowed NIR reflectances
close to 50% and consistent cooling effects.[33, 44]
Being the NIR reflective features strongly
depending on the supramolecular packing, polymer drawing may promote the exfoliation of
the dispersed PBIs aggregates, thus causing the loss of NIR reflection that in turn
substantially reduces the cooling effect of film surfaces.
In this work, we propose for the first time the use of P-black as a pigment for low-density
polyethylene (LLDPE) aimed to endow the derived films with a responsive behavior to
mechanical deformations both in the visible and in the NIR region of the spectrum of light.
The external stress applied to the LLDPE film is thus detectable as color variations in the
5
visible and reflectance reduction in the NIR, this last causing a prompt temperature variation
of the film surface under IR irradiation.
2. Experimental part
2.1 Materials
Paliogen® Black L0086 (P-black) was provided by BASF and used without further
purification. Linear low density polyethylene (LLDPE, Dowlex SC 2107, Melt flow index,
190 °C/2.16 kg 2.3 g/10 min, d = 0.917 g/cm3) was supplied by Dow Plastics, USA. The
remaining chemicals were obtained from Sigma-Aldrich.
2.2 P-black/LLDPE film preparation
A desired amount of P-black was dispersed under vigorous stirring in a 5 wt.% LLDPE
solution in toluene at 80 °C. After sonication for 5 min at 400 W and 24 kHz with Hielscher’s
UP 400 S probe, the solvent was removed by rotary evaporation and the obtained solid blend
eventually compression molded at 180 °C for 5 min into thin film with a thickness between
120 and 150 μm.
2.3 Methods
The thickness of the LLDPE films was measured with a CM1S dial indicator (Borletti, Milan,
Italy) with ruby movement bearing. Differential scanning calorimetry (DSC) was performed
on LLDPE films under nitrogen atmosphere by using a Mettler Toledo StarE System,
equipped with a DSC822c module and following the procedure reported in the literature.[45]
Solid-state drawings of the binary films were performed on a thermostatically controlled hot
stage at 90 °C. The draw ratio (Dr), defined as the ratio between the final and the initial
length of the samples, was determined by measuring the displacement of ink-marks printed
6
onto the films before stretching. UV-Vis spectra of P-black/LLDPE films were recorded at
room temperature over the wavelength range of 350–800 nm in polarized light with the help
of a Perkin-Elmer Lambda 650 equipped with motor-driven Glan-Taylor linear polarizers.
UV–Vis–NIR reflectance measurements of P-black/LLDPE films were recorded at room
temperature over the wavelength range of 350–2500 nm by using an Agilent Cary 5000
spectrophotometer equipped with a 150 mm integration sphere. A commercially available
100W IR lamp (Kerbl, Buchbach, Germany) was used for the heating tests. The P-
black/LLDPE films were placed over the black surface of a Leneta® checkerboard chart and
irradiated at a distance of 20 cm for 5 seconds and the temperature measured by means of a
FLIR™ E6 infrared thermo-camera (FLIR, Wilsonville, OR, USA). The thermal images were
opened by the FLIR Tools software (version 2.1) by using the iron palette image setup. The
optical microscope analysis was accomplished on a Nikon Eclipse Ni-E equipped with a
Thorlab LPVISE200-A polarizer and a Nikon DS Ri2 camera. Particle analysis was
performed using the public domain ImageJ 1.52k software version image analyzer program
developed by the National Institutes of Health (USA) and available on Internet at
https://imagej.nih.gov/ij/index.html.
2.4 Computational details
P-black molecules have been investigated computationally to analyze and interpret their
optical and structural features. We adopted various models to elucidate the available
experimental data in both solvent/vacuum medium and in condensed phases.
2.4.1 Solvent/vacuum calculations
The molecular structure of P-black molecules has been relaxed in the ground electronic state
(GS) using the Gaussian 16 package,[46]
adopting the B3LYP exchange and correlation
functional[47, 48]
in conjunction with 6-31+G(d,p) basis set and Grimme’s D3-BJ dispersion
7
correction:[49]
this level of theory proved to be suitable in a previous investigation of some of
us on a similar system (dye Paliogen Red)[41]
. All relaxed structures are potential energy
minima, as all normal modes have a positive frequency. Calculations of electronic excited
states have been performed with the TD-DFT approach using the range-separated exchange
and correlation functional CAM-B3LYP,[50]
to better describe charge-transfer transitions and
the spectral shape. Solvent effect was simulated using an implicit solvation model
(polarizable continuum model).[51]
2.4.2 Crystal-embedded calculations
Periodic calculations have been carried out with the Crystal 17[52]
code at the B3LYP-D3
level with a modified all-electron 6-31+G(d,p) basis set to match that of non-periodic
calculations. Numerical DFT integration has been performed considering 75 radial points and
974 angular points, ensuring an error on the integrated electron density to an accuracy of 10–5
e per unit cell. The Coulomb and exchange series were truncated with threshold values of 10–
7, 10
–7, 10
–7, 10
–7, and 10
–21. A tolerance of 10
–7 a.u. has been used for the convergence of the
self-consistent field procedure. Cell parameters and atomic positions have been let free to
relax during structural optimization. Convergence was determined from the root mean square
and absolute value of the largest component of the forces and displacements, considering
default values (0.00045 and 0.00067 au for the forces, and 0.0018 and 0.0027 a.u. for the
displacements, respectively). The crystalline structure of P-black belongs to the triclinic P1
space group, with flat perylenetetracarboxylic diimide portions packed in stacks through π–π
interactions, with experimental lattice parameters of a = 4.09 Å, b = 9.71 Å, and c = 17.11 Å,
α = 98.82°, β = 91.07°, γ = 101.58°.[53]
The optimized lattice parameters obtained are a = 3.99
Å, b = 9.78 Å, c = 16.96 Å, α = 96.72°, β = 90.04°, and γ = 101.67°. In addition, the flat
portions of neighboring molecules are found at about 3.49 Å apart, with respect to an
8
experimental value of 3.59 Å. To create a more cubic-like box, we adopted a 7 × 3 × 2
monoclinic supercell, resulting in a simulation box of volume ∼28 × 29 × 34 Å3.
Starting from the optimized crystal structure obtained, a large supercell was built and
partitioned into three zones, according to the SC-Ewald approach.[54]
At the inner first zone
treated at the QM level, two different clusters with either one, two, or three P-black
molecules have been considered. The intermediate second zone consisted of point charges
fixed at the value of the Mulliken atomic charges of the periodic calculation, while the point
charge values of the outer third zone have been adjusted to impose the exact Madelung
potential of the infinite periodic system on the first two zone sites. Further details can be
found in ref 51.[55]
Vertical TD-DFT calculations with the aforementioned models (embedded
monomer and dimer of P-black) have been carried out with Gaussian 16, thus including the
effects of the crystal environment. The embedded dimer model was also used to test the
dependence of computed spectra on the intermolecular distance and relative translation. All
calculations (both embedded and not) have been carried out using the Pople’s 6-31+G(d,p)
basis set, and dispersion forces were modeled employing Grimme’s D3-BJ correction.
3. Results and discussion
P-black is an insoluble PBI pigment that was dispersed by ultrasonication in toluene
containing the 5 wt% of linear low-density polyethylene (LLDPE). LLDPE films containing
different concentrations (2.5, 5 and 10 wt%) of P-black were prepared by compression
molding of the respective LLDPE mixtures. The presence of P-black did not substantially
altered the thermal properties of LLDPE films, whose crystallinity and melting point were
only slightly enhanced at the highest pigment content of 10 wt% (Table S1). No thermal
transitions attributed to P-black were detected up to 300 °C in agreement with the thermal
9
behavior of PBI pigments.[43, 56]
The UV-Vis spectra P-black/LLDPE films show absorption
maxima centered at 430 and 680 nm (Figure S1a), which correspond to that displayed in
toluene dispersion. Those bands progressively widen with concentration until reaching almost
a continuous contribution all over the visible spectrum at the highest pigment content of 10
wt%. Absorbance flattening at the highest P-black content was attributed to saturation
phenomena. Moreover, P-black/LLDPE films did not display any emission behavior, thus
suggesting the de-excitation pathways was mainly governed by the typical aggregation-
caused quenching phenomenon of PBI insoluble pigments.[57]
Calculations were employed to investigate the nature of the electronic transitions that
originate the P-black color as a function of the local environment (solution, embedded in
matrix). To this end, we have simulated P-black molecules in vacuo, in trichlorobenzene
(TCB) solvent, and in an electrostatic field that mimic a crystal environment, refer to
Computational detail for the technical part. In Figure 1 (left panel) we report the computed
shapes of the optical spectra obtained from a two-molecules model. This latter model has
been chosen as it is able to describe not only absorption from a single molecule but also to
include in the simplest way excitonic effects, if they are present. This two-molecules model
has been proven to be relevant in the case of a similar compound (Paliogen Red).[41]
Of note
the calculations including the electrostatic field of the crystal environment (hereafter referred
to as embedded model) are here considered as the simplest model to simulate absorption
within the LLDPE matrix since micro-crystalline aggregates are formed in this matrix and the
effect of the low polarity polymer matrix on the absorption properties of this micro-crystal is
expected to be negligible.
The calculations carried out in gas and solution phases yield very similar spectral shapes,
with just a hypsochromic shift observed when going from vacuum to solution. The
corresponding transitions have a local character, without any appreciable inter nor intra
10
molecular charge-transfer (Figure 1, right panel), as measured also according refined
quantum descriptors.[58]
Figure 1. Left panel up: chemical structure of Paliogen® Black L0086 (P-black). Left panel
down: computed optical spectra at the TD-CAM-B3LYP level of theory in TCB (black),
vacuo (red), and embedded into the crystal field (blue); the curved are smoothed with
Lorentzian functions of half width at half height of 0.33 eV, while vertical lines are actual
vertical Sn←S0 transitions. Right panel: main orbitals involved into the first (I) and second
(II) calculated band, for the solution/gas calculations (black) and the crystal-embedded one
(blue).
Two main peaks can be located, around ~610 nm and ~410 nm for the solution phase: these
values are within 0.2 eV from the observed peaks in solid phase, in agreement with the
accurate level that may be expected from TD-DFT calculations and in agreement with the
known tendency of the CAM-B3LYP functional to overestimate excitation energies.[59]
A
more detailed analysis of the computational data in vacuum and in solution can be found in
the Supporting Information (see Figures S8-S12). The model expected to reproduce the
absorption behavior in an aggregate phase, referred to as crystal-embedded and described in
the computational details in the crystal embedded calculation section, yields instead a less
structured spectrum, with significant absorption in the 300 – 700 nm range of wavelengths,
thus spanning a large portion of the visible range (as expected from a black material). The
11
nature of the first excitation (I* in Figure 1) is also different, with a more pronounced inter-
molecular charge-transfer character, a behavior found also in the TD-DFT study of so-called
Paliogen Red molecule (or Pigment Red 179)[41]
when simulated embedded into a crystal.
The DCT[58]
quantum descriptor for charge transfer suggests an hole-electron distance of
~3.15Å, to be compared with an intermolecular distance between P-black molecules in the
crystal of ~3.4 Å. Models which include just a single P-black molecule or do not take into
account the effect of the environment yields a vanishing value for the DCT descriptor. A more
detailed description of the embedded model can be found in the Supporting Information (see
Figures S13-S14 and Table S1-S2).
3.1 UV-Vis response to mechanical drawing
The P-black/LLDPE films were then oriented by uniaxial drawing at different draw ratios up
to a maximum of 6 (elongation = 500%). The anisotropic behavior of the stretched films was
evaluated by UV-Vis spectroscopy in polarized light (Figure 2), i.e. at different polarization
angle with respect to the drawing direction of the film.
12
Figure 2. UV-vis absorption spectra as a function of the polarization angle for P-
black/LLDPE oriented films containing a) 2.5 wt%, b) 5 wt%, c) 10 wt% of pigment; d)
photos of the same 5 wt% P-black/LLDPE oriented film taken by superimposing a linear
polarized oriented parallel (0°) and perpendicular (90°) with respect to the drawing direction.
Dr = 6 in all cases.
The mechanical drawing of the P-black/LLDPE films conferred to the plastic materials a
well-defined dichroic behavior under polarized light. It was worth noting that by varying the
direction of the polarization angle with respect to the drawing direction of the films the
absorption bands experienced an opposite behavior (Figure 2a-c). Notably, the band at 430
nm increased its intensity whereas that at longer wavelengths (i.e., 680 nm) decreased its
contribution, flanked by the existence of a clear isosbestic point at about 570 nm, thus
supporting the existence of two different populations of chromophoric assemblies. The
behavior was confirmed for all the films investigated, therefore suggesting that dichroic
assemblies of pigment molecules were generated also at the highest pigment content of 10
wt%, notwithstanding the reduced absorbance variations caused by possible signal flattening
a)
c)
b)
d)0° 90°
2.5 wt% 5 wt%
10 wt%
13
due to saturation phenomena (Figure 2c). We did not find such behavior in unstretched
samples (Figure S1b), only negligible absorbance variations were detected in polarized light
and possibly attributed due to uneven orientation of P-black aggregates during film formation
by compression molding.
Notably, the mechanochromic response was clearly visible simply by observing the oriented
portions of the LLDPE films under a linear polarizer (Figure 2d). The color changed
accordingly to the absorption variations from yellow-green (0°) to dark-cyan (90°).
The effect provided by the P-black content and the draw ratios on the chromogenic behavior
was also studied in terms of the absorbance variation ΔA (Table 1 and Figure S2).
14
Table 1. Absorbance variations at 430 and 680 nm for P-black/LLDPE films at different
pigment content and draw ratio (Dr). ΔA = A90°-A0°
Entry Dr = 3 Dr = 4 Dr = 6
ΔA430 ΔA680 ΔA430 ΔA680 ΔA430 ΔA680
2.5 wt% P-
black/LLDPE 0.43 -0.30 0.51 -0.40 0.43 -0.30
5 wt% P-
black/LLDPE 0.20 -0.18 0.63 -0.41 0.78 -0.45
10 wt% P-
black/LLDPE 0.16 -0.10 0.18 -0.12 0.22 -0.16
The data reported in Table 1 revealed that the dichroic phenomenon was already obtained at
the smallest deformation extent (Dr = 3) and particularly evidenced in the LLDPE films
containing the lowest 2.5 wt% content, i.e. reaching absorbance variations of 0.43. P-
black/LLDPE films containing the 5 wt% of the pigment revealed as the most sensitive
towards mechanical drawing, with ΔA values progressively raising with draw ratio. Notably,
a maximum of ΔA ∼ 0.8 was reached at the highest Dr = 6. Conversely, LLDPE films
containing the 2.5 and 10 wt% of P-black showed lower sensitivity towards uniaxial drawing
with ΔA values mostly similar for all the draw ratio investigated. This phenomenon could be
possibly attributed for the former to a maximum chromophore orientation already gathered
during the early stages of uniaxial deformation and for the latter to the difficulties of
orienting the large content of P-black assemblies (i.e., 10 wt%) along the drawing direction
and confined in the amorphous phase between polymer crystallites even at the highest Dr = 6.
Nevertheless, absorbance flattening caused by saturation phenomena in LLDPE films
containing the 10 wt.% of P-black cannot be excluded, thus affecting ΔA linear variations.
It was worth noting that the absorption band at about 430 nm appeared more sensitive to
uniaxial deformation than that at about 680 nm for all the P-black/LLDPE films investigated.
This behavior was firstly attributed to the absorbance flattening issue, since the absorption
band at higher wavelength was also the more intense. Nevertheless, such phenomenon can be
15
traced back to the transition dipole moments of the optical excitations. Considering as the
simplest model to simulate absorption of P-black within the LLDPE the embedded crystal
model, since micro-crystalline aggregates are formed in this matrix and the effect of the low
polarity polymer matrix on the absorption properties of this micro-crystal is expected to be
negligible, we analyze the transition dipole moments of all the most intense Sn←S0
transitions. Here it is worth to recall that even if the computed transitions energies are
expected be overestimated (i.e., predicted at shorter wavelengths with respect to what
experimentally observed) due to known well documented limitations of the employed level of
theory (i.e., the CAM-B3LYP exchange-correlation functional used which overestimates
transition energies due to its high content of Hartree-Fock exchange) the nature of the
electronic transition is expected to be correctly reproduced. Therefore dipole moments,
depending on ground and excited state densities are expected to be qualitatively reliable.
The computed dipole moments show a certain extent of variability as reported in Table S3 of
the Supporting Information. In particular, transitions #11 and #27 expected to contribute to
the higher energy band show significantly different absorptions if oriented differently in a
single crystal. In fact, this anisotropy increases when a translation is made along the x-axis
(see Tables S3 and S4 of the Supporting Information), suggesting that the second band of the
spectrum is more sensible to the orientation with respect to incoming light when subject to a
lateral stress, as experimentally observed.
Optical microscopy taken on pristine and oriented P-black/LLDPE films (e.g., those
containing the 5 wt% of P-black, Figure S3) revealed that the mechanical drawing was
particularly effective in reducing the size of P-black aggregates from about 30-40 μm to 5-10
μm and in orienting them towards the drawing direction. Notably, microscopy images taken
on oriented films at Dr = 6 and in polarized light (Figure S4) confirmed the results gathered
from UV-Vis spectroscopy (Figure 1). It was worth noting that all the oriented samples
16
displayed color variations in absorption as a function of the polarization angle (i.e., 0° and
90°) with P-black 5-10 μm-sized aggregates mostly oriented towards the orientation direction
of the film. The dichroic behavior appeared more evident for the oriented P-black/LLDPE
film containing the 2.5 and 5 wt% of pigment and in agreement with the data reported in
Table 1. The highest P-black content of 10 wt% strongly affected the light transmission of the
film and rendered difficult the determination of the aggregates anisotropy throughout the film
sample.
Nevertheless, notwithstanding the high absorption of the films, optical microscopy was
effective in revealing the dichroic behavior of P-black/LLDPE films at the early stages of
mechanical deformation and containing the highest pigment content (10 wt% of P-black,
Figure S5). Notably, the uniaxial elongation corresponding to Dr = 1.2 conferred LLDPE
film a chromogenic response in polarized light, thus suggesting that even at very small
LLDPE deformations the supramolecular structure of P-black assemblies resulted effectively
affected. This result was particularly relevant since it demonstrated the sensitivity of the
designed P-black/LLDPE system in providing a prompt mechanochromic response towards
uniaxial deformation.
3.2 NIR response to mechanical drawing
We then investigated the influence of the P-black content and the polymer uniaxial drawing
on the film reflectivity in the visible and NIR region. In agreement with literature data, the
reflectance spectra were dependent on the optical features of the P-black chromophoric unit,
i.e. a strong absorption in the visible region and maximum reflectivity around 800 nm flanked
by a long tail throughout the NIR region (Figure 3).[34, 42]
17
Figure 3. UV–VIS-NIR reflectance spectra of P-black/LLDPE films at different P-black
content. The black dashed lines delimit the visible region (400–700 nm).
Notably, reflectance values progressively raised from 10% to about 51% on passing from the
neat LLDPE film (gray line) to that doped with the 10 wt% of pigment (red line) thanks to
the NIR reflective features of P-black aggregates.[33, 44]
NIR reflectances close to 50% are
particularly beneficial for the development of dark organic coatings with cooling
characteristics since the affected wavelength region represents about the 25% of the total
solar energy.[36]
Visible reflectances of the pigment doped films (i.e., from 400 to 750 nm)
were lower than that of the neat LLDPE due to the strong absorption of P-black aggregates.
50
40
30
20
10
Re
fle
cta
nce
(%
)
2400200016001200800400
wavelength (nm)
LLDPE 2.5 wt.% 5.0 wt.% 10 wt.%
18
Figure 4. UV–VIS-NIR reflectance spectra of P-black/LLDPE films at different P-black
content before (pristine) and after uniaxial deformation at Dr = 6. Thermal images of the
same films with temperatures recorded for the oriented and unoriented portion of the films
after 5 second exposure to an IR lamp (nominal power 100W, distance from the sample 20
cm)
The mechanical drawing of the P-black/LLDPE films (Dr = 6) effectively affected the
reflectance of the films with decreasing of about 30-40% at around 800 nm. This
phenomenon might be possibly addressed to a combination of effect: the first resides on the
fact that uniaxial drawing caused P-black dilution throughout the oriented film portion; the
second consist on the partial exfoliation of the pigment aggregates during deformation as
revealed by optical microscopy (Figure S3). The reduction of the average aggregate size of P-
black assemblies has been recently reported to adversely affect pigment reflectivity and, in
turn, the pigment cooling characteristics.[44]
33.6 °C
39.3 °C
33.0 °C
39.2 °C
32.2 °C
37.9 °C
2.5 wt%
5 wt%
10 wt%
50
40
30
20
10
Re
flecta
nce
(%
)
2400200016001200800400
wavelength (nm)
pristine Dr = 6
50
40
30
20
10
Re
flecta
nce (
%)
2400200016001200800400
wavelength (nm)
pristine Dr = 6
50
40
30
20
10
Re
fle
cta
nce
(%
)
2400200016001200800400
wavelength (nm)
pristine Dr = 6
19
The films were then placed over the black surface of a Leneta® checkerboard chart and
irradiated by means of an IR lamp for 5 seconds to investigate the different cooling features
of the oriented and pristine portions of the P-black doped LLDPE films. Thermal images
taken during lamp irradiation revealed consistent temperature raising of the oriented LLDPE
film of about 5-6 °C and in agreement with reflectance variations. In summary, the addition
of P-black endowed LLDPE film with NIR-reflective and cooling characteristics as
demonstrated by the progressive temperature reduction from 38.7 °C to 32.2 °C on passing
from the neat LLDPE film (Figure S6) to that doped with the 10 wt% of pigment (Figure 4).
As soon as the mechanical drawing was applied to the films, reflectance reduction of about
20-30% caused temperature raising close to 6 °C. Thickness variations occurred during film
drawing supposedly contribute to the thermal response specifically for the highly oriented
LLDPE samples. Anyway, temperature variations were also detected for the initially
oriented 10 wt% P-black/LLDPE film (Dr = 1.2) with the deformed film portion 4.5 °C
warmer than the pristine counterpart (Figure S7).
4. Conclusions
This work enabled the use of P-black as an unique pigment that once embedded into LLDPE
films provided combined optical variations in the visible and reflectivity response in the NIR
after mechanical uniaxial deformation. Notably, LLDPE films containing the 2.5-10 wt.% of
P-black showed a dichroic absorption profile in linearly polarized light with clear isosbestic
points and color variations from yellow-green to dark-cyan. This feature was addressed by
density functional theory calculations to the different anisotropic behavior of the transition
dipole moments of the P-black chromophoric assemblies within the oriented LLDPE matrix.
Mechanical drawing was also responsible in reducing the average size of P-black aggregates
from ∼30-40 μm in the pristine film to ∼5-10 μm after maximum film deformation at Dr = 6,
20
thus also causing substantial reflectivity decrease of ∼30-40% due also to the concomitant P-
black dilution all over the oriented portion of the LLDPE film. Such reflectivity loss was
ingeniously exploited since the oriented film in contact with a black substrate displayed a
noteworthy warming of 5-6 °C maximum when illuminated with an IR lamp for 5 seconds.
Both optical and thermal outputs revealed very sensitive to mechanical drawing thus opening
a new avenue for the direct determination of mechanical deformations of plastic films.
Acknowledgements
This work was supported by the MIUR-PRIN 20179BJNA2. This project has also received
funding from the European Research Council (ERC) under the European Union’s Horizon
2020 Research and Innovation Program (grant agreement no. 648558 STRIGES CoG).
References
[1] P. Bamfield, M. Hutchings, "Chromic Phenomena: Technological Applications of Colour
Chemistry, 3rd Edition", Royal Society of Chemistry, 2018, p. 782 pp.
[2] A. Pucci, G. Ruggeri, Journal of Materials Chemistry 2011, 21, 8282.
[3] F. Ciardelli, G. Ruggeri, A. Pucci, Chemical Society Reviews 2013, 42, 857.
[4] F. Würthner, T. E. Kaiser, C. R. Saha-Möller, Angewandte Chemie - International Edition
2011, 50, 3376.
[5] C. Lowe, C. Weder, Advanced Materials 2002, 14, 1625.
[6] A. Pucci, Sensors 2019, 19, 4969.
[7] F. Donati, A. Pucci, C. Cappelli, B. Mennucci, G. Ruggeri, Journal of Physical Chemistry
B 2008, 112, 3668.
[8] G. Prampolini, F. Bellina, M. Biczysko, C. Cappelli, L. Carta, M. Lessi, A. Pucci, G.
Ruggeri, V. Barone, Chemistry - A European Journal 2013, 19, 1996.
[9] D. W. R. Balkenende, S. Coulibaly, S. Balog, Y. C. Simon, G. L. Fiore, C. Weder,
Journal of the American Chemical Society 2014, 136, 10493.
[10] C. Calvino, E. Henriet, L. F. Muff, S. Schrettl, C. Weder, Macromol. Rapid Commun.
2020, 41, 1900654.
[11] C. Calvino, Y. Sagara, V. Buclin, A. P. Haehnel, A. del Prado, C. Aeby, Y. C. Simon, S.
Schrettl, C. Weder, Macromolecular Rapid Communications 2019, 40, 1800705.
21
[12] A. Pucci, R. Bizzarri, G. Ruggeri, Soft Matter 2011, 7, 3689.
[13] F. Martini, S. Borsacchi, M. Geppi, G. Ruggeri, A. Pucci, Polymer Chemistry 2014, 5,
828.
[14] M. Zhang, L. Zhao, R. Zhao, Z. Li, Y. Liu, Y. Duan, T. Han, Spectrochim. Acta, Part A
2019, 220, 117125.
[15] R. Zhao, L. Zhao, M. Zhang, Z. Li, Y. Liu, T. Han, Y. Duan, K. Gao, Dyes Pigm. 2019,
167, 181.
[16] M. Karman, E. Verde-Sesto, C. Weder, Y. C. Simon, ACS Macro Lett. 2018, 7, 1099.
[17] C. Calvino, L. Neumann, C. Weder, S. Schrettl, Journal of Polymer Science, Part A:
Polymer Chemistry 2017, 55, 640.
[18] G. I. Peterson, M. B. Larsen, M. A. Ganter, D. W. Storti, A. J. Boydston, ACS Applied
Materials and Interfaces 2015, 7, 577.
[19] Q. Wang, G. R. Gossweiler, S. L. Craig, X. Zhao, Nature Communications 2014, 5,
4899.
[20] D. R. T. Roberts, S. J. Holder, Journal of Materials Chemistry 2011, 21, 8256.
[21] P. Zhang, X. Shi, A. P. H. J. Schenning, G. Zhou, L. T. de Haan, Advanced Materials
Interfaces 2020, 7, 1901878.
[22] K. Suenaga, K. Uemura, K. Tanaka, Y. Chujo, Polymer Chemistry 2020, 11, 1127.
[23] K. Kawasaki, D. Aoki, H. Otsuka, Macromolecular Rapid Communications 2020, 41,
1900460.
[24] C. Calvino, E. Henriet, L. F. Muff, S. Schrettl, C. Weder, Macromolecular Rapid
Communications 2020, 41, 1900654.
[25] C. Calvino, Y. Sagara, V. Buclin, A. P. Haehnel, A. del Prado, C. Aeby, Y. C. Simon, S.
Schrettl, C. Weder, Macromolecular Rapid Communications 2018, 40, 1800705.
[26] Y. Sagara, M. Karman, E. Verde-Sesto, K. Matsuo, Y. Kim, N. Tamaoki, C. Weder,
Journal of the American Chemical Society 2018, 140, 1584.
[27] C. Calvino, A. Guha, C. Weder, S. Schrettl, Advanced Materials 2018, 30, 1704603.
[28] A. Nowak-Król, F. Würthner, Organic Chemistry Frontiers 2019, 6, 1272.
[29] D. Görl, X. Zhang, F. Würthner, Angewandte Chemie - International Edition 2012, 51,
6328.
[30] Z. Chen, A. Lohr, C. R. Saha-Möller, F. Würthner, Chemical Society Reviews 2009, 38,
564.
[31] F. Donati, A. Pucci, G. Ruggeri, Physical Chemistry Chemical Physics 2009, 11, 6276.
[32] A. Pucci, C. Cappelli, S. Bronco, G. Ruggeri, Journal of Physical Chemistry B 2006,
110, 3127.
[33] P. Minei, M. Lessi, L. Contiero, S. Borsacchi, F. Martini, G. Ruggeri, M. Geppi, F.
Bellina, A. Pucci, Solar Energy 2020, 198, 689.
[34] M. Mazhar, M. Abdouss, K. Gharanjig, R. Teimuri-Mofrad, M. Zargaran, Journal of
Coatings Technology and Research 2017, 14, 207.
[35] J. Qu, Z. N Zhang, W. D Shi, Y. X Zhang, T. Xue, X. Zhang, R. P Zhang, J. Qin, J.
Song, Z. Song, W. Zhang, Y. Shi, T. Zhang, X. Xue, R. Zhang, Z. Hongqiang, Z. Zhang, X.
Wu, "The Optical Properties of Black Coatings and Their Estimated Cooling Effect and
Cooling Energy Savings Potential", 2014, p. 68.
[36] B. Kaur, S. N. Bhattacharya, D. J. Henry, Dyes and Pigments 2013, 99, 502.
[37] A. Muscio, Climate 2018, 6, 12.
[38] BASF, "Paint it cool! Pigments for solar heat management in paints".
[39] H. Akbari, M. Pomerantz, H. Taha, Solar Energy 2001, 70, 295.
[40] F. Mahmoudi Meymand, M. Mazhar, M. Abdouss, J. Coat. Technol. Res. 2019, 16, 439.
[41] F. Muniz-Miranda, P. Minei, L. Contiero, F. Labat, I. Ciofini, C. Adamo, F. Bellina, A.
Pucci, ACS Omega 2019, 4, 20315.
22
[42] M. Mazhar, M. Abdouss, K. Gharanjig, R. Teimuri-Mofrad, Progress in Organic
Coatings 2016, 101, 297.
[43] F. Martini, M. Geppi, G. Barcaro, S. Monti, L. Contiero, G. Ruggeri, M. Lessi, A. Pucci,
F. Bellina, S. Borsacchi, The Journal of Physical Chemistry C 2020.
[44] F. Martini, P. Minei, M. Lessi, L. Contiero, S. Borsacchi, G. Ruggeri, M. Geppi, F.
Bellina, A. Pucci, Dyes and Pigments 2020, 179, 108401.
[45] M. Carlotti, G. Gullo, A. Battisti, F. Martini, S. Borsacchi, M. Geppi, G. Ruggeri, A.
Pucci, Polymer Chemistry 2015, 6, 4003.
[46] M. J. Frisch, G. W. Trucks, H. B. Schlegel, G. E. Scuseria, M. A. Robb, J. R.
Cheeseman, G. Scalmani, V. Barone, G. A. Petersson, H. Nakatsuji, X. Li, M. Caricato, A. V.
Marenich, J. Bloino, B. G. Janesko, R. Gomperts, B. Mennucci, H. P. Hratchian, J. V. Ortiz,
A. F. Izmaylov, J. L. Sonnenberg, Williams, F. Ding, F. Lipparini, F. Egidi, J. Goings, B.
Peng, A. Petrone, T. Henderson, D. Ranasinghe, V. G. Zakrzewski, J. Gao, N. Rega, G.
Zheng, W. Liang, M. Hada, M. Ehara, K. Toyota, R. Fukuda, J. Hasegawa, M. Ishida, T.
Nakajima, Y. Honda, O. Kitao, H. Nakai, T. Vreven, K. Throssell, J. A. Montgomery Jr., J.
E. Peralta, F. Ogliaro, M. J. Bearpark, J. J. Heyd, E. N. Brothers, K. N. Kudin, V. N.
Staroverov, T. A. Keith, R. Kobayashi, J. Normand, K. Raghavachari, A. P. Rendell, J. C.
Burant, S. S. Iyengar, J. Tomasi, M. Cossi, J. M. Millam, M. Klene, C. Adamo, R. Cammi, J.
W. Ochterski, R. L. Martin, K. Morokuma, O. Farkas, J. B. Foresman, D. J. Fox, "Gaussian
16", Wallingford, CT, 2016.
[47] C. Lee, W. Yang, R. G. Parr, Physical Review B 1988, 37, 785.
[48] A. D. Becke, The Journal of Chemical Physics 1993, 98, 5648.
[49] S. Grimme, S. Ehrlich, L. Goerigk, Journal of Computational Chemistry 2011, 32, 1456.
[50] T. Yanai, D. P. Tew, N. C. Handy, Chemical Physics Letters 2004, 393, 51.
[51] J. Tomasi, B. Mennucci, R. Cammi, Chemical Reviews 2005, 105, 2999.
[52] R. Dovesi, A. Erba, R. Orlando, C. M. Zicovich-Wilson, B. Civalleri, L. Maschio, M.
Rérat, S. Casassa, J. Baima, S. Salustro, B. Kirtman, WIREs Computational Molecular
Science 2018, 8, e1360.
[53] M. C. R. Delgado, E.-G. Kim, D. A. d. S. Filho, J.-L. Bredas, Journal of the American
Chemical Society 2010, 132, 3375.
[54] M. Klintenberg, S. E. Derenzo, M. J. Weber, Computer Physics Communications 2000,
131, 120.
[55] L. Wilbraham, C. Adamo, F. Labat, I. Ciofini, Journal of Chemical Theory and
Computation 2016, 12, 3316.
[56] B. Kaur, N. Quazi, I. Ivanov, S. N. Bhattacharya, Dyes Pigm. 2012, 92, 1108.
[57] J. Mei, N. L. C. Leung, R. T. K. Kwok, J. W. Y. Lam, B. Z. Tang, Chemical Reviews
2015, 115, 11718.
[58] T. Le Bahers, C. Adamo, I. Ciofini, Journal of Chemical Theory and Computation 2011,
7, 2498.
[59] F. Muniz-Miranda, M. C. Menziani, A. Pedone, The Journal of Physical Chemistry C
2014, 118, 7532.