Manuel Noblesse VOIP

GB - 1

TABLE OF CONTENTS

INSTALLATION ............................................................................................................. 2HANDSET ..................................................................................................................... 3BASE UNIT ................................................................................................................... 4INFORMATION ON THE LCD-DISPLAY ...................................................................... 4SETTINGS FOR USE OVER THE FIXED TELEPHONE LINE .................................... 5USE OF THE PHONE OVER THE FIXED TELEPHONE LINE ................................. 10REGISTERING HANDSET TO THE BASE UNIT ...................................................... 13THE PHONEBOOK-MEMORY ................................................................................... 15CALLER ID (CLIP) ...................................................................................................... 18DIRECT CALL ............................................................................................................. 19USE OF THE TELEPHONE VIA THE PC ................................................................... 20SETTINGS FOR USE VIA THE PC .............................................................................. 22SKYPE™ ...................................................................................................................... 23SKYPE™ CALL LIST .................................................................................................. 27SKYPE™ VOICEMAIL ................................................................................................. 27MSN® MESSENGER / WINDOWS LIVETM MESSENGER ........................................... 30SJ-PHONE / NET2PHONE ........................................................................................... 31VOIPBUSTER, NETAPPEL, VOIPSTUNT & OTHERS ................................................ 32TROUBLESHOOTING .................................................................................................. 35IMPORTANT SAFETY MEASURES ............................................................................. 37

m_NoblesseVOIPSingle_GB_.pmd 09.11.2006, 11:071

GB - 2

INSTALLATION

INSTALLATION OF THE HANDSET

see Illustration I

• Remove the battery compartment door.• Insert 2 AAA Ni-MH batteries in the battery compartment.• Close the battery compartment door by pushing it back on the handset.

! When replacing the batteries, ALWAYS use good quality Ni-MH rechargeable batteries. Never use otherbatteries or conventional alkaline batteries! The use of wrong batteries can cause irrevocable damage toyour appliance!

Important!Before you start using your cordless phone definitely, it first has to be charged during 16 hours. Youshould do this without connecting it to the telephone line.

• To charge the handset you can place it on the base unit.• The battery-indicator on the display indicates the status of the battery capacity.• The battery capacity is 5 days in Standby-mode and 13 hours conversation.

INSTALLATION OF THE BASE UNIT

see Illustration II

• Click the plug of the adaptor in the connection plug on the backside of the base unit (1) and plug the adaptor into the wall socket.• Click one end of the telephone cord in the connection point on the backside of the base unit (2) and the other end in the

telephone plug.• This telephone plug can now be plugged into the wall socket of your telephone connection point.


GB - 3

Important!If you install the NOBLESSE VOIP correctly, a connection between the handset and the base unit willbe made automatically.On the LCD-display appears the number of the base unit (BU-1) and of the handset (HS-1).

HANDSETsee Illustration III

1. • To call and to answer a call.

2. • To go through the different steps of the Programming menu.• Could also be used as FLASH-key.

3. • To adjust the voice volume during a call.4. • Switches the microphone temporarily off during a call.

• To delete numbers or characters.• Goes to the previous position in the Programming menu.• During programming you can always go back to Standby-mode by keeping this key pressed during 2 sec.

5. • To display the numbers of the Phonebook.

6. • To switch off the keypad lock.7. Keypad.8. • To make and to answer calls via your normal fixed telephone line.9. • Activates programming and confirms the settings after changes.

• Activates intercom communications (with use of multiple handsets).10. • Redial.

• Could also be used as PAUSE-key.11. • To go through the different steps of the Programming menu.

• To take a look at the numbers of the Caller ID memory.• To switch the ‘Speakerphone’ function of the handset on/off.

12. LCD-display.


GB - 4

BASE UNIT

see Illustration IV

1. Charge-Led This led lights during charging and flashes during calling.

Important!If the handset is being placed on the base unit, this led ALWAYS should light. If it does not light, this meansthat the handset was not placed correctly on the base unit or that the AC adaptor was not installed properly,so that the handset can not be charged.

2. Handset-search-button To locate the registered handset. Is also used to register a new handset (with use of multiplehandsets).

3. Charge-contact points Keep them clean and dust-proof to make charging possible.

INFORMATION ON THE LCD-DISPLAY

Indicates that you are active in the Phonebook.Indicates that you are active in the Programming menu.Indicates the capacity of the battery.Flashes when the capacity of the battery is starting to get low.Indicates when the ringertone volume for external calls via the normal fixed line ánd for PC calls is switched off.Indicates a conversation via the normal fixed telephone line.Flashes when you receive a call.

x Indicates that the microphone has been temporarily switched off during a call.

Indicates that some numbers are stored in the Caller ID memory.

Flashes when a new call that you have not seen yet, has been stored.This function only works if you have subscribed it with your telephone company.


GB - 5

)) Indicates that the ‘Speakerphone’-function is active.

Indicates that the handset is within effective range of the base unit.Flashes when the handset is too far out of range of the base unit.

PC Indicates a VOIP/PC conversation.Flashes when you receive a PC call.If somebody leaves a message in your mailbox, this icon will appear.This function only works if you have subscribed it with your telephone company.

SETTINGS FOR USE OVER THE FIXED TELEPHONE LINE

Important!This chapter only describes the settings for the NOBLESSE VOIP phone with use over the normal fixedtelephone line (analogue/PSTN line).

GENERAL GUIDELINES

• The phone always needs to be in Standby-mode before you can start programming.• To exit the Menu, you can use the key.

LANGUAGE

Press the key. � Press the key until “SETTING “ appears on the display. � Press the key. � Press the key againuntil “LANGUAGE “ appears on the display. � Press the key. � Use the key until the required language appears on thedisplay. � Finally press the key once again to confirm the language. [You will hear a confirmation beep.]

DATE & TIME

Press the key. � Press the key until “SETTING ” appears on the display. � Press the key. � Press the key againuntil “DATE/TIME ” appears on the display. � Press the key. “YEAR ” appears on the display. � Enter the right number of the year(f.e. 06 for 2006). � Press the key to confirm. “MONTH ” appears on the display. � Enter the right month. � Press the


GB - 6

key to confirm the month. “DAY ” appears on the display. � Enter the right day. � Press the key to confirm. “HOUR ” appearson the display. � Enter the right hour. � Press the key to confirm. “MINUTE ” appears on the display. � Enter the rightminutes. � Press the key to confirm. [You will hear a confirmation beep.]

RINGER MELODY

You can choose from 9 different ringer melodies and 9 polyphonic ring tones.Press the key. � Press the key until “RING SEL ” appears on the display. � Press the key. “EXTERNAL ” appears on the

display. � Press the key. “MELODIES ” appears on the display. � Press the key once again and use the and key

to search the required melody. � Press the key to confirm your favourite melody for all external calls. [You will hear aconfirmation beep.]

RINGER VOLUME

You can choose from 10 different ringer volume levels.Press the key. � Press the key until “RING SEL ” appears on the display. � Press the key. “EXTERNAL” appears on thedisplay. � Press the key and then the key. “VOLUME” appears on the display. � Press the key and then use the

& key to search the required ringer volume. � Finally press the key to confirm the right external ringer volume. [You willhear a confirmation beep.]

Important!If you choose for volume-level ‘0’, the ringer tone will be switched off completely.

DIALING WITH OR WITHOUT SOUND SIGNAL

Press the key. � Press the key until “KEY SETUP” appears on the display. � Press the key, the key and finallythe key again. � Use the key to make your choice: “CLICK ON” or “CLICK OFF”. � Finally press the key to confirm yourchoice. [You will hear a confirmation beep.]

LOCKING AND UNLOCKING THE KEYPAD

Press the key. � Press the key until “KEY SETUP” appears on the display. � Press the key and then use the key


GB - 7

until “KEY LOCK” appears on the display. � Press the key and then use the key to make your choice: “LOCK” (to lock thekeypad) or “UNLOCK” (to unlock the keypad). � Finally press the key to confirm your choice. [You will hear a confirmation beep.]

Remark:You can unlock the keypad by keeping the key pressed during 2 seconds.

HANDSET NAME

Press the key. � Press the key until “SETTING” appears on the display. � Press the key and then the until“HS NAME“ appears on the display. � Press the key. � Enter the required name. � Press the key to confirm the handsetname. [You will hear a confirmation beep.]

PROGRAMMING A PIN-CODE

A number of functions, like f.i. “Blocking numbers” of the NOBLESSE VOIP only can be programmed with a PIN-Code.PIN-Code with delivery = ‘0000’.

How to change this PIN-Code?Press the key. � Press the key until “SETTING” appears on the display. � Press the key and then the key until“PIN-CODE” appears on the display. � Press the key once again. � Enter your old PIN-Code (with delivery = ‘0000’) followed

by . � Enter now your new PIN-Code (max. 8 numbers) followed by the key. � Enter your new PIN-Code once againfollowed by . [You will hear a confirmation beep.]

BLOCKING NUMBERS

You can block several numbers with the NOBLESSE VOIP. The number you blocked has a max. of 5 numbers.Examples of possible blocked numbers are:• ‘00’: international numbers can not be dialed if ‘00’ is programmed as a blocked number.• ‘06’ or ‘0475’: mobile numbers that begin with f.i. ‘06’ of ‘0475’ can not be dialed if they are programmed as blocked numbers.• ‘0900’: can also be programmed as a blocked number.


GB - 8

HOW TO BLOCK A NUMBER?

Press the key. � Press the key until “SETTING” appears on the display. � Press the key and then the key until“BARRING” appears on the display. � Press the key and enter your PIN-Code (with delivery = ‘0000’). � Press the keyagain and enter the number that you would like to block. � Press the key and enter 1. � Press the key to confirm theblocking. [You will hear a confirmation beep.]

To program multiple blocked numbers (max. 5), you proceed the same way as written above. Only after entering your PIN-Code you press the key to block the next number. On the display appears “BAR NUM 2”. Then you proceed with the differentsteps as written above.

HOW TO DELETE A BLOCKED NUMBER?

Press the key. � Press the key until “SETTING” appears on the display. � Press the key and then the key until

“BARRING” appears on the display. � Press the key and enter your PIN-Code (with delivery = ‘0000’). � Press the keyonce. � Now simply use the key to delete the programmed blocked numbers. � Press the key to confirm. [You will heara confirmation beep.]

TONE/PULSE ( * )

Press the key. � Press the key until “SETTING” appears on the display. � Press the key. � Press the key onceagain until “DIAL MODE” appears on the display. � Press the key. “TONE” appears on the display. � Use the key to makeyour choice: “TONE” or “PULSE”. � Finally press to confirm your choice. You will hear a confirmation beep.

(*) This setting is NOT used in the majority of the European countries where only “TONE” dialling is available.

FLASH-KEY

The FLASH-key offers the possibility to use various services of your telephone company or can be used as through-connectkey when the NOBLESSE VOIP is connected to a PBX.


GB - 9

Remark:The flash-time is different for each country. Check the correct setting with your local telephonecompany before programming the flash-time.

Press the key. � Press the key until “SETTING” appears on the display. � Press the key. � Press the key until“RECALL” appears on the display. � Press the key. � Use the key to make your choice: you can choose 100ms (SHORT)

or 300ms (LONG). � Press the key to confirm. [You will hear a confirmation beep.]

‘RESET’ OF THE APPLIANCE

This action makes it possible to undo all the changes and to go back to the default settings (ringer volume, ringer melody, language,keytones, blocked numbers,…).Press the key. � Press the key until “SETTING” appears on the display. � Press the key. � Press the key onceagain until “RESET” appears on the display. � Press the key and enter your PIN-Code (= ‘0000’ with delivery). � Press the

key once again to confirm the “RESET“. [You will hear a confirmation beep.]

Important!• This way you can not recover the forgotten PIN-Code.• The memory of the Phonebook is not being erased.• The handset will not be deregistered.

DEFAULT SETTINGS

Key lock UnlockKey click Click onEarpiece volume Level 3External ringer Melody 1External ringer Volume 5Language EnglishPIN code Unchanged


GB - 10

COMPLETE RE-INSTALLATION

With the NOBLESSE VOIP it is possible to re-install your telephone completely, without having to use the PIN-Code.

Important!• The original PIN-Code will be recovered (=’0000’ with delivery).• All default settings will be recovered.• The memory of the Phonebook will be erased.• The handset will be de-registered and therefore needs to be registered once again.

Remove the batteries from the handset. � Keep the key pressed and put the batteries back in the handset until the handset

rings continuously and the display lights. � Release the key and press the key. � You will hear a beep tone. �

Press the key shortly. � “RESET” appears on the display. � Press the key to confirm or remove the batteries to

cancel. � “RESET OK” appears on the display. [You will hear a confirmation beep.] � “NOT SUB” appears on the display. Now youcan register the handset once again.

USE OF THE PHONE OVER THE FIXED TELEPHONE LINE

Important!This chapter only describes the use of the NOBLESSE VOIP phone over the normal fixed telephone line(analogue/PSTN line).

SWITCHING ON/OFF

While installing the NOBLESSE VOIP and placing the battery, the telephone is automatically being switched on!If you wish to switch a handset completely off, you can do this as following:Press the key and use the key until “POWER OFF?“ appears on the display. � Press to confirm. [The handset willnot ring and the last dialed numbers will be erased from the memory.] � To switch the handset back on after switching it off,press any key. � Your telephone is back in Standby-mode.


GB - 11

CALLING

Two possibilities:1. Press and enter the required telephone number.2. Enter the required telephone number and press .

If you enter a wrong number, press the key once to delete 1 number and for a few seconds to delete the whole number.

RECEIVING AND ENDING A CALL

When you receive a call, you will hear a sound signal on the handset:Press to answer the call. � Press the key again to end the call.

ADJUSTING THE VOICE VOLUME

During a call you can adjust the voice volume.Press . The current voice volume appears on the display. � Choose a level from 1 to 5 by using the keypad. � Press toconfirm.

‘MUTE’-KEY

During a call, press the key to switch the microphone off. � x appears on the display. [The person on the other end of the line cannot hear you, but you can hear the person on the other end of the line.] � Press the key to switch the microphone back on.

‘SPEAKERPHONE’-KEY

With this key you can switch on the Speakerphone of the handset to make a completely handsfree call.

Press . � On the display appears )). � Press again to switch off the microphone and to continue your conversation

without Speakerphone via the handset. � Press to finally end the call.

Remark:During a call you can adjust the volume of the speakerphone as indicated above in the chapter“Adjusting the voice volume”.


GB - 12

REVIEWING AND DIALING THE LAST DIALED NUMBERS

With the NOBLESSE VOIP you can review the 5 last numbers that were dialed with this phone.Press the key. “REDIAL“ appears on the display. � Press the key: the last dialed number appears on the display. � Press

again to review the previous number. � Finally press to dial the number that is now showing on the display.

CALL DURATION

The telephone automatically shows the duration of the calls.This remains on the display during a few seconds after the call, before it turns back to Standby-mode.

Remark:The call duration automatically starts counting after pressing the key, even when there is no connection.

HANDSET-SEARCH-BUTTON

Press the key of the base unit very shortly to page the handset that has gone missing. � The handset beeps for a moment.� Press any key of the handset to stop the beeping.

USING PREFIX DIALING

The NOBLESSE VOIP allows you to set a Prefix Number, which will always be dialed out automatically before you enter the telephonenumber you want to dial. This number will also be dialed when you call numbers from the phonebook memory, redial memory etc.Example:Prefix number - 1609Telephone number - 0123456789Prefix dialing sequence - 16090123456789

SETTING A PREFIX NUMBER

Press the key. � Press the key until “PREFIX“ appears on the display. � Press the key. � Enter the required prefix

number. This prefix number will always be dialed out automatically. � Press the key to confirm. [You will hear a confirmationbeep.] � Press the key to return to Standby mode.


GB - 13

Remark:The prefix number will not appear on the display.

DELETING A PREFIX NUMBER

Press the key. � Press the key until “PREFIX “ appears on the display. � Press the key. � Press the key to delete theprefix number. � Press the key to confirm. [You will hear a confirmation beep.] � Press the key to return to Standby mode.

DIALING WITHOUT PREFIX NUMBER

The prefix number will always be dialed out automatically (also when you call numbers from the phonebook memory, redial memory etc.).When you want to dial a number without prefix number, but you don’t want to delete the prefix number you have set in the phone,you can do this as following:Enter the required telephone number or select the number you want to dial in, for example, the Redial memory. � Press andhold the key for 3 seconds. � The requested number will now be dialed without prefix number.

REGISTERING HANDSET TO THE BASE UNIT

Handset 1: in Standby-mode you read from the display: “BU-1 HS-1“.If f.i. by pressing a wrong key appears that the handset is not registered to the base unit anymore, you can still do the following:

How to proceed?Press during 10 sec. of the base unit. � The red LED on the base unit starts to flash. � Press of the handset you would like

to register. � Press until “BASE SUB“ appears on the display. � Press followed by the base unit number. � The icon

flashes and on the display appears “SEARCHING“ followed by a code. � Press again and enter the PIN-Code (with delivery =‘0000’). � Press . � If registering has succeeded, you will hear a confirmation beep.

Important!The base unit stays during 3 min. in registering-mode.If registering the handset has not gone well, you could better start all over again.


GB - 14

DEREGISTERING THE HANDSET FROM THE BASE UNIT

As described above you can, if necessary, registering the handset again to the base unit. With use of multiple handsets you canalso deregister them.

How to proceed?Press the key of the handset you do not wish to deregister. � Press the key until “SETTING“ appears on the display. �

Press the key and then the key until “REMOVE HS“ appears on the display. � Press the key and enter the PIN-Code(= ‘0000’ with delivery). � Press the key and enter the handset number that you would like to delete. � Press the key.� If deregistering was successful, you will hear a confirmation beep. If this is not the case, you will hear 3 short beeps that indicatethat you have entered a wrong digit.

SELECTING A BASE UNIT

If your handset is registered to multiple base units, you can choose with which base your handset needs to communicate. Youhave 2 possibilities:

1. “MANUAL“: Choose the required base unit manually. You can make a choice between all base units to which the handset is registered.2. “AUTO“: Choose the required base unit automatically. The handset will automatically search for the base unit with the best connection.

Selecting manuallyPress the key. � Press the key until “SETTING“ appears on the display. � Press the key and then the key until

“BASE SEL“ appears on the display. � Press the key. � Press the key until “MANUAL“ appears on the display. � Press the key. � Enter the number of the required base unit. � Press the key to confirm. � “SEARCHING“ appears on the display. �

If the base unit is found, you will hear a confirmation beep.

Selecting automaticallyPress the key. � Press the key until “SETTING“ appears on the display. � Press the key and then the key until“BASE SEL“ appears on the display. � Press the key. � Press the key until “AUTO“ appears on the display. � Press the

key. � “SEARCHING“ appears on the display. � If the base unit is found, you will hear a confirmation beep.


GB - 15

THE PHONEBOOK-MEMORY

You can store 200 names and numbers in the Phonebook of the NOBLESSE VOIP.

STORING A NUMBER AND NAME IN THE PHONEBOOK-MEMORY

Press the key. � Press the key until “PHONE BOOK“ appears on the display. � Press the key. “SEARCHING“ appears onthe display. � Press the key until “ADD NEW“ appears on the display. � Press the key. “NAME“ appears on the display. �

Enter the name you would like to store. Use the keypad to program the name. � Press the key to confirm the name. �Enter the telephone number that you would like to store accordingly. � Press the key to confirm the telephone number. [Youwill hear a confirmation beep.]

OR

The phone is in Standby-mode. � Enter the number that you would like to store. � Press and hold the key during 2

seconds. “NAME“ appears on the display. � Enter the name that you would like to store. � Press and hold the key during2 seconds to confirm. [You will hear a confirmation beep.]

Use of the keypad

Key Press 1 Press 2 Press 3 Press 4 Press 5 Press 6 Press 7 Press 8 Press 9 Press 10 Press 11 once time times times times times times times times times times times

1 space # & ( ) * , - . / 1 2 A B C 2 3 D E F 3 4 G H I 4 5 J K L 5 6 M N O 6 7 P Q R S 7 8 T U V 8 9 W X Y Z 9 0 space _ 0


GB - 16

Remark:• To delete a wrong input, press the key.• Press the key to change a character from a small character to a capital and vice versa.

SELECTING SPECIFIC LANGUAGE CHARACTERS

The NOBLESSE VOIP offers you the possibility to choose specific language characters to enter data in the phonebook. You canchoose between following input languages:• “CHAR. SET 1“: English• “CHAR. SET 2“: Latin• “CHAR. SET 3“: Greek• “CHAR. SET 4“: RussianPress the key. � Press the key until “PHONE BOOK“ appears on the display. � Press the key. � Press the keyuntil “SET CHAR“ appears on the display. � Press the key. � Press the key until the required language charactersetting appears on the display. � Press the key to confirm. [You will hear a confirmation beep.]

SEARCHING A NUMBER IN THE PHONEBOOK

Press the key. � Press the key until “PHONE BOOK“ appears on the display. � Press the key. “SEARCHING“ appears onthe display. � Press the key. � Enter the first letter(s) of the name that you would like to search. � Press the key. The

first name that begins with these letters appears on the display. � Use the and key to scroll through the completephonebook memory.

OR

Press and hold the key during 2 seconds. � Use the and key to scroll through the complete phonebookmemory.

CALLING A NUMBER OF THE PHONEBOOK

2 possibilities:


GB - 17

1. The phone is in Standby-mode. � Press and hold the key during 2 seconds and use the and key to scroll

through the Phonebook-memory. � Press when the required number appears on the display.

2. The phone is in Standby-mode. � Press . � Press and hold the key during 2 seconds and use the and

key to scroll through the Phonebook-memory. � Press when the required number appears on the display.

DELETING A NUMBER AND NAME FROM THE PHONEBOOK-MEMORY

Press the key. � Press the key until “PHONE BOOK“ appears on the display. � Press the key. “SEARCHING“ appears

on the display. � Press the key once again until “DELETE“ appears on the display. � Press the key. � Use the and

key to scroll through the Phonebook-memory. � Press the key when the number that you would like to delete appears

on the display. “DELETE?“ appears on the display. � Press the key to confirm. [You will hear a confirmation beep.]

OR

The phone is in Standby-mode. � Press and hold during 2 seconds and use the and key to scroll through the

Phonebook-memory. � Press the key when the number that you would like to delete appears on the display. “DELETE?“appears on the display. � Press the key to confirm. [You will hear a confirmation beep.]

EDITING A NUMBER AND NAME OF THE PHONEBOOK-MEMORY

Press the key. � Press the key until “PHONE BOOK“ appears on the display. � Press the key. “SEARCHING“ appears onthe display. � Press the key once again until “EDIT” appears on the display. � Press the key. � Use the and

key to scroll through the Phonebook-memory. � Press again when the number that you would like to edit appearson the display. � Edit the name and in order to do this you can use f.i. the key. � Press to confirm the correct name.� Edit the number. � Press to confirm the correct number. [You will hear a confirmation beep.]


GB - 18

CALLER ID (CLIP)

Important!This chapter only describes the Caller ID function of the NOBLESSE VOIP phone over the normal fixedtelephone line (analogue/PSTN line).

Before you can use this service, you first have to take a Caller ID-subscription with your telephone company.• With Caller ID you can see, before you pick up the phone, the number of the person that is calling you on the display of the

NOBLESSE VOIP.• If this number already has been stored in your Phonebook, the name also appears on the display. If this is not the case,

“NO NAME” appears on the display.• If the caller has blocked the CLIP-function, “WITHHELD“ appears on the display.• With Caller ID you can also see all the numbers that called you during your absence.• You can call these numbers directly and/or store them in the Phonebook.• The NOBLESSE VOIP has a Caller ID memory of 30 numbers.

REVIEWING NUMBERS

flashes: new calls have been stored in the Caller ID memory.

stops flashing as soon as you have seen all the new calls.

Press . “CLIP” appears on the display. � Press the key. The name and number of the last received call appear on the

display. � Press the key to review the date and the time of the call. � Press the key to go the previously stored call and

use the key to receive some extra information. � This way you can review the complete Caller ID memory. � Use the key to exit the list.

CALLING NUMBERS FROM THE CALLER ID LIST

Press to enter the Caller ID list. “CLIP” appears on the display. � Press the key. � Press until the required numberappears on the display. � Press the key. The number is dialed.


GB - 19

STORING NUMBERS FROM THE CALLER ID LIST IN THE PHONEBOOK

Press to enter the Caller ID list. “CLIP” appears on the display. � Press the key. � Press until the required number

appears on the display. � Press and hold the key during 2 seconds. � Press the key to store the number. � To add aname to the number, you proceed the same way as described in the chapter “Editing a number and name of the Phonebook-memory”.

DELETING NUMBERS FROM THE CALLER ID LIST

Delete 1 numberPress to enter the Caller ID list. “CLIP” appears on the display. � Press the key. � Press until the number that youwould like to delete appears on the display. � Press the key to delete the number. “DELETE?” appears on the display. � Pressthe key to confirm [You will hear a confirmation beep] or press the key to cancel.

Delete all numbersPress to enter the Caller ID list. “CLIP” appears on the display. � Press the key. � Press and hold the key until “DELETE

ALL” appears on the display. � Press the key to confirm [You will hear a confirmation beep] or press the key to cancel.

DIRECT CALL

WHEN DO YOU USE THIS FUNCTION?

If you program a number under “Direct Call” and turn it ON, this number will be automatically dialed out if you press any key.Example: If your child is home alone and you wish to be reachable in a very easy way, you can program under “Direct Call” yourmobile phone number for instance. This number will then be dialed out immediately by pressing any key of the NOBLESSE VOIP.

PROGRAMMING THE DIRECT CALL NUMBER

Press the key. � Press the key until “DIRECT” appears on the display. � Press the key again. “NUMBER” appears

on the display. � Enter the Direct Call number. � Press the key to confirm. � If necessary, you can always delete orchange the currently programmed number by using the key.


GB - 20

TURNING THE DIRECT CALL NUMBER ON

Press the key. � Use the key until “DIRECT” appears on the display. � Press the key for 2 seconds until “DIRECT

ON” appears on the display. [You will hear a confirmation beep.] � This Direct Call number will now be dialed out automaticallyif you press any key. � To end the conversation, press the key.

TURNING THE DIRECT CALL NUMBER OFF

Press the key twice. [You will hear a confirmation beep.] � The NOBLESSE VOIP will return to Standby-Mode.

USE OF THE TELEPHONE VIA THE PC

MINIMUM SYSTEM REQUIREMENTS

To use your NOBLESSE VOIP telephone as optimal as possible, you need to have the following minimum systemrequirements:• PC with Windows 2000 or Windows XP;• 64 MB free memory;• 128 MB free space on the hard disk;• Internet connection of 64 Kbps or higher.

INSTALLING THE SOFTWARE

Important!• Please note that the PC driver software is compatible with your Windows 2000/XP computer. In case

you have installed any other VOIP driver software, please remove it before installation of the PremierNoblesse VOIP driver software.

• Wait to plug the USB cable in the PC connection. Do this only after installing the software and restartingyour PC.

• Start your PC and activate your Internet connection.


GB - 21

• Make sure one of the following programs is installed:- Skype™: http://www.skype.com/download- MSN® Messenger / Windows LiveTM Messenger: http://messenger.msn.com- SJ-Phone : http://www.sjlabs.com/sjp.html- Net2Phone: http://web.net2phone.com- VoipBuster: http://www.voipbuster.com- NetAppel: http://www.netappel.fr- VoipStunt: http://www.voipstunt.com- VoipDiscount: http://www.voipdiscount.com- poivY: http://www.poivy.com- SIPDiscount: http://www.sipdiscount.com- VoipCheap: http://www.voipcheap.com- InternetCalls: http://www.internetcalls.com- SparVoip: http://www.sparvoip.de- FreeCall: http://www.freecall.com- WebcallDirect: http://www.webcalldirect.com

• Insert the software-CD in your CD-romstation.• If the program doesn’t start automatically, go to “Start” and choose “Run”. Enter D:\CD_Setup.exe. If the letter of your CD-

romstation isn’t D, replace the D by the correct letter of your CD-romstation.• Follow the different steps as indicated by the installation wizard.• Reboot your PC after finalizing the installation process.• Plug one end of the USB cable in the connection point at the back side of the base unit of the NOBLESSE VOIP and the other

end in the USB-port of your PC.• Windows will install the proper USB-driver for your telephone.• If a screen appears with the Windows Logo Test, click ‘Continue’. If this screen doesn’t appear, nothing needs to be

done.• Select the required VOIP telephone program for Skype™, MSN® Messenger, Windows LiveTM Messenger, SJ-Phone,

Net2Phone, VoipBuster, NetAppel, VoipStunt, VoipDiscount, poivY, SIPDiscount, VoipCheap, InternetCalls, SparVoip,FreeCall or WebcallDirect.

• Open the required VOIP telephone program.


GB - 22

SETTINGS FOR USE VIA THE PC

Important!This chapter only describes the settings for the NOBLESSE VOIP phone with use over the Internet (VOIP).

RINGER MELODY

You can choose from 9 different ringer melodies and 9 polyphonic ring tones.Press the key. � Press the key until “RING SEL” appears on the display. � Press the key. � Press the keyuntil “PC RING” appears on the display. � Press the key. “MELODIES” appears on the display. � Press the key once

again and use the and key to search the required melody. � Press the key to confirm your favorite melody forall PC calls. [You will hear a confirmation beep.]

RINGER VOLUME

You can choose from 10 different ringer volume levels.Press the key. � Press the key until “RING SEL” appears on the display. � Press the key. � Press the key

until “PC RING” appears on the display. � Press the key and then the key. “VOLUME” appears on the display. � Press

the key and then use the and key to search the required ringer volume. � Finally press the key to confirmthe right PC ringer volume. [You will hear a confirmation beep.]

Important!If you choose for volume-level ‘0’, the ringer tone will be switched off completely.

Please make sure that only 1 VOIP telephone program is in use. Please close all other VOIP telephoneprograms in order to avoid technical difficulties between them.


GB - 23

ADJUSTING THE VOICE VOLUME

During a PC call you can adjust the voice volume.Press . The current voice volume appears on the display. � Choose a level from 1 to 5 by using the keypad. � Press toconfirm.

‘MUTE’-KEY

During a PC call, press the key to switch the microphone off. � x appears on the display. [The person on the other end of theline can not hear you, but you can hear the person on the other end of the line.] � Press the key to switch the microphone back on.

PC-TIME

When you activate the PC-time setting, each call will be stored according to the date and time settings of your PC-clock.Press the key. � Press the key until “SETTING“ appears on the display. � Press the key. � Press the key

once again until “PC-TIME“ appears on the display. � Press the key. � Use the key to make your choice: “ON” or “OFF”.� Finally press the key to confirm your choice. [You will hear a confirmation beep.]

SKYPE™

Important!This chapter only describes the operation of the NOBLESSE VOIP phone with use of SkypeTM.

Important!• Make sure that you are using Skype™ version 1.2.8 or higher.• Make sure that Skype™ is selected as VOIP telephone program in the NOBLESSE VOIP program.


GB - 24

• In Standby mode your net status appears on the display of the NOBLESSE VOIP (online, away, etc).• “NO CONNECT” appears on the display if the VOIP telephone program is not opened or if the USB-

connection failed.

SETTING THE NET STATUS

You can set your net status via your NOBLESSE VOIP handset.Press the key. � Press the key until “NET STATUS“ appears on the display. � Press the key. � Press the keyuntil the required net status appears on the display. � Press the key to confirm. [You will hear a confirmation beep.]

Remark:If your net-status is “Offline” or “Do not disturb” the handset will not ring with an incoming Skype™ call.

ALARMLIST

If you activate the “Alarmlist”, a notification will appear on your display when the net status of one of your contact personschanges.Press the key. � Press the key until “SETTING” appears on the display. � Press the key. � Press the key

until “LIST ALERT“ appears on the display. � Press the key. � Use the key to make your choice: “ON” or “OFF”. � Finallypress the key to confirm your choice. [You will hear a confirmation beep.]

CALLING VIA THE ONLINE FRIENDSLIST

The online friendslist is the list with your personal Skype™ contact persons.


GB - 25

Press the key. The Skype™ nickname of the first contact person in your friends list appears on the display. � Use the

and the key to scroll through your online friends list. � Press the key to view the corresponding ID-name ofyour contact person. � Press the key once again to go back to the Skype™ nickname of your contact person. � Press

the key to call the required contact person.


With an incoming Skype™ call the Skype™ nickname of the caller appears on the display of your NOBLESSE VOIP.

Press the key to answer the call. � Press the key once again to end the call.

Remark:When you have a Skype™ subscription, the number of the caller will appear on the display during aSkypeIn call.

MAKING A SKYPEOUT CALLSkypeOut makes it possible to make cheap calls via the PC to fix and mobile numbers over the whole world.

Important!• Before being able to use this service, you first have to buy some SkypeOut credits.• When you want to dial a number using SkypeOut, you always have to enter “+” or “00”, followed by

the international country code, before the number that you want to call (f.e. 0032 for Belgium). Thisalso applies for national calls.

Enter the required telephone number. � Press the key. � Press the key once again to end the conversation.

Note:With the NOBLESSE VOIP you can review the 5 last dialed numbers that were dialed with this phone viaSkype™. The last dialed SkypeOut numbers will also be saved here.


GB - 26

REVIEWING AND DIALING THE LAST DIALED NUMBERS

With the NOBLESSE VOIP you can review the 5 last dialed numbers that were dialed with this phone.Press the key. � Press the key until “PC-OUT“ appears on the display. � Press the key: the Skype™ nicknameof the last contact person that you called, appears on the display. � Press again to review the previous number. �

Press the key to view the corresponding ID-name of your contact person. � Press the key to view the date and time

of the call. � Finally press the key to dial the number that is now showing on the display.

SWITCHING BETWEEN SKYPE™ CALLS AND NORMAL PSTN CALLS

Important!When you receive a call via the normal fixed line and a Skype™ call at the same time, the first call willappear on the display. You can answer one of these calls by pressing the corresponding key: for theSkype™ call, for the normal PSTN call.

Incoming Skype™ call during PSTN conversationWhen a Skype™ call comes in during a normal conversation over the normal fixed line, the Skype™ nickname of the secondcaller appears on the display and you will hear a beep. The PC icon flashes on the display.

Press the key to end the first call. � The handset starts to ring. � Press the key to answer the Skype™ call.

OR

Press the key. � Press the key until “SWITCH” appears on the display. � Press the key. The PSTN call will be puton hold and you will be connected with the Skype™ call. � To switch back to the PSTN call, you repeat the different steps

described above. � Press the corresponding keys to end both calls: for the Skype™ call, for the normal PSTN call.

Incoming PSTN call during Skype™ callWhen a PSTN call comes in during a Skype™ call, the number and the name of the caller appear on the display (If CallerID is available).

Press the key to end the first call. � The handset starts to ring. � Press the key to answer the PSTN call.


GB - 27

OR

Press the key. � Press the key until “SWITCH” appears on the display. � Press the key. The Skype™ call will beput on hold and you will be connected with the PSTN call. � To switch back to the Skype™ call, you repeat the different steps

described above. � Press the corresponding keys to end both calls: for the Skype™ call, for the normal PSTN call.

SKYPE™ CALL LIST

The NOBLESSE VOIP has a memory of 30 Skype™ calls.

REVIEWING NUMBERS

Press the key. � Press the key until “PC-IN” appears on the display. � Press the key. The Skype™ nickname

of the contact person that last called you, appears on the display. � Press the key to view the date/time of the call andthe net status of the contact person. � Use the key to scroll through the call list.

Note:The symbol after “PC-IN” indicates that there is a new call that you have not seen yet. This symbol willdisappear as soon as you have seen all the new calls.

CALLING NUMBERS FORM THE CALL LIST

Press the key. � Press the key until “PC-IN“ appears on the display. � Press the key until the required call

appears on the display. � Press the key.

SKYPE™ VOICEMAIL

Before you can use this service, you first have to subscribe to Skype™ Voicemail.

�


GB - 28

LISTENING TO RECEIVED VOICEMAIL MESSAGESWhen you have received a voicemail message, the icon appears on the display. � Press the key. � Press the key. “VOICEMAIL” appears on the display. � Press the key. “INBOX” appears on the display. � Press the key. � TheSkype™ nickname of the last contact person who left a message will appear on the display. If this is a message that you havenot played yet, the icon will also be shown on the display. � Press the key to view the corresponding ID-name of yourcontact person. � Press the key once again to go back to the Skype™ nickname of your contact person. � Press the

key to view the date/time of the call and the net status of the contact person. � To play the received voicemail message,press the key. � To stop playing the voicemail, press the key once again.

Note:• By pressing the key for a few seconds in Standby-mode, you can access the voicemail menu

directly. “INBOX” appears on the display. Then you proceed with the same steps as described above.• The upload of the voicemail messages from the PC to the NOBLESSE VOIP takes a short period. Please

wait until the upload is complete to access the “INBOX” menu. If the upload has not been completedyet, “––“ will appear on the display and the handset will return to the “INBOX” menu.

• If you have not pressed the key to stop playing the message, the NOBLESSE VOIP will automaticallyreturn to the “INBOX” menu when the voicemail message has been played completely.

• When you have listened to a voicemail message, the icon will disappear after the Skype™ nicknameof the person who left the message. The Skype™ nickname will remain in the list of received voicemailmessages. Go to the “INBOX” menu as described above and use the key to scroll through this list.

• If you use the � icon on your PC to play the voicemail message, the Skype™ nickname of the personwho left the message appears on the display of your Noblesse VOIP. � Press the key to listen to thevoicemail through your handset. � Press the key once again to stop playing the message.

DELETING RECEIVED VOICEMAIL MESSAGES

If you don’t want to listen to a voicemail message, you can only delete this message using your PC.Open Skype™. � Go to “CALL LIST” and click on the voicemail icon. � Select the voicemail message that you wantto remove. � Click on the dustbin icon to delete the message. � The icon disappears from the display of yourNOBLESSE VOIP.


GB - 29

SENDING VOICEMAIL MESSAGES

Press the key. � Press the key. “VOICEMAIL” appears on the display. � Press the key. “INBOX” appears on the

display. � Press the key. “OUTBOX” appears on the display. � Press the key to open the list of all your online and

offline Skype™ contacts. � Use the and the key to scroll through the list. � Press the key to view the

corresponding ID-name of your contact person. � Press the key once again to go back to the Skype™ nickname of your

contact person. � Press the key when the name of the contact person to whom you want to send a voicemail message

appears on the display. You can now start recording your voicemail. � Press the key once again to end the recording.� Your handset returns to the “OUTBOX” menu and your voicemail message will be sent to the selected contact person.

Note:• By pressing the key for a few seconds in Standby-mode, you can access the voicemail menu

directly. “INBOX” appears on the display. Press the key. “OUTBOX” appears on the display. Then youproceed with the same steps as described above.

• While viewing the friendslist, you can enter the first letter of the name to search quickly.• When you select a contact person on your PC and choose “Send Voicemail”, the Skype™ nickname of

this person appears on the display of your NOBLESSE VOIP. � Press the key to record your voicemailmessage. You will hear the greeting message of your contact person, followed by a “beep”, afterwhich you can enter your message. � Press the key once again to end the recording and send themessage.

• If you have not subscribed to Skype™ Voicemail, you can also send voicemail messages, but only tocontact persons who have subscribed to the Skype™ Voicemail service. In this case, only the names ofthese contact persons will appear in the “OUTBOX” menu.


GB - 30

MSN® MESSENGER / WINDOWS LIVETM MESSENGERImportant!This chapter only describes the operation of the NOBLESSE VOIP phone with use of MSN® Messenger /Windows LiveTM Messenger.

Important!• Make sure that MSN® Messenger is selected as VOIP telephone program in the NOBLESSE VOIP program.

• The connection between MSN® Messenger / Windows LiveTM Messenger and your NOBLESSE VOIP onlyworks if MSN® Messenger / Windows LiveTM Messenger is opened and minimalized in the application tray.

CALLING

Press the key to open the list with contact persons. � Use the and key to scroll through the list of contactpersons. � Press the key to call the required contact person.


With an incoming call you will only get a notification on your PC screen that you are being called.Press the key to open the list with contact persons. � Use the and key to find the caller. � Press the keyto answer the call. � Press the key once again to end the call.


GB - 31

Important!On your PC a separate window will appear showing the following question:If you close this window, the current conversation will be ended. Would you like to proceed?Click ‘Yes’ to confirm the ending of your call. If you do not confirm the ending of your call on your PC, thecall will not be ended.

SJ-PHONE / NET2PHONEImportant!This chapter only describes the operation of the NOBLESSE VOIP phone with use of SJ-Phone andNet2Phone.

Important!Make sure that SJ-Phone or Net2Phone is selected as VOIP telephone program in the NOBLESSE VOIPprogram.

CALLINGEnter the required telephone number. � Press the key.

RECEIVING AND ENDING A CALLWith an incoming call “EXT” appears on the display of your NOBLESSE VOIP and the PC icon starts to flash.Press the key to answer the call. � Press the key once again to end the call.


GB - 32

VOIPBUSTER, NETAPPEL, VOIPSTUNT & OTHERS

Important!This chapter only describes the operation of the NOBLESSE VOIP phone with use of VoipBuster. The othertelephone services operate more or less the same way as VoipBuster.

Important!• Make sure that you are using VoipBuster version 2.11 or higher.• Make sure that VoipBuster is selected as VOIP telephone program in the NOBLESSE VOIP program.

ALARMLIST

If you activate the “Alarmlist”, a notification will appear on your display when the net status of one of your contact personschanges.Press the key. � Press the key until “SETTING ” appears on the display. � Press the key. � Press the key

until “LIST ALERT ” appears on the display. � Press the key. � Use the key to make your choice: “ON ” or “OFF ”. � Finallypress the key to confirm your choice. [You will hear a confirmation beep.]

CALLING VIA THE ONLINE FRIENDSLIST

The online friendslist is the list with your personal VoipBuster contact persons.


GB - 33

Press the key. The VoipBuster nickname of the first contact person in your friends list appears on the display. � Use the

and the key to scroll through your online friends list. � Press the key to view the corresponding ID-name of yourcontact person. � Press the key once again to go back to the VoipBuster nickname of your contact person. � Press the

key to call the required contact person.


With an incoming VoipBuster call the VoipBuster nickname of the caller appears on the display of your NOBLESSE VOIP.

Press the key to answer the call. � Press the key once again to end the call.

MAKING AN EXTERNAL CALLWith VoipBuster it is also possible to make cheap calls via the PC to fix and mobile numbers over the whole world.

Important!• Please check the website of the VOIP telephone service for more information.

Important!• Before being able to use this service, you first have to buy some credits.• When you want to dial an external number, you always have to enter “+” or “00”, followed by the

international country code, before the number that you want to call (f.e. 0032 for Belgium). This alsoapplies for national calls.

Enter the required telephone number. � Press the key. � Press the key once again to end the conversation.

SWITCHING BETWEEN VOIPBUSTER CALLS AND NORMAL PSTN CALLS

Important!When you receive a call via the normal fixed line and a VoipBuster call at the same time, the first call willring. You first have to answer the first call before being able to answer the second one by pressing thecorresponding keys: for the VoipBuster call, for the normal PSTN call.


GB - 34

If the first call comes via the normal fixed line:- The icon will flash.- The callers number and name (if stored in the phonebook) will appear on the display.- You will hear the ringer melody for fixed calls.- You have to press the key to answer the call.

If the first call is a VoipBuster call:- The PC icon will flash.- The callers number and name (if stored in the phonebook) of the call via the normal fixed line will appear on the display.- You will hear the ringer melody for VoipBuster calls.- You have to press the key to answer the call.

Incoming VoipBuster call during PSTN conversationWhen a VoipBuster call comes in during a normal conversation over the normal fixed line, the VoipBuster nickname of thesecond caller appears on the display and you will hear a beep. The PC icon flashes on the display.

Press the key to end the first call. � The handset starts to ring. � Press the key to answer the VoipBuster call.

ORPress the key. � Press the key until “SWITCH ” appears on the display. � Press the key. The PSTN call will beput on hold and you will be connected with the VoipBuster call. � To switch back to the PSTN call, you repeat the different

steps described above. � Press the corresponding keys to end both calls: for the VoipBuster call, for the normalPSTN call.

Incoming PSTN call during VoipBuster callWhen a PSTN call comes in during a VoipBuster call, the number and the name of the caller appear on the display (If CallerID is available).

Press the key to end the first call. � The handset starts to ring. � Press the key to answer the PSTN call.


GB - 35

ORPress the key. � Press the key until “SWITCH ” appears on the display. � Press the key. The VoipBuster call willbe put on hold and you will be connected with the PSTN call. � To switch back to the VoipBuster call, you repeat the different

steps described above. � Press the corresponding keys to end both calls: for the VoipBuster call, for the normalPSTN call.

TROUBLESHOOTING

Problem Cause Solution

No indication on the display. The batteries are empty. � Check the position of the batteries.� Charge the batteries.

No tone. Bad connection of the telephone. Check the connection of yourtelephone.

There is a tone, but a call is The wrong dialing mode is set. Change the setting of the dialingimpossible. mode.

The icon flashes. � The telephone is too far away � Take your handset closer to from the base unit. the base unit.� The base unit has no power. � Check the connection of your

base unit.� The handset is not registered. � Register the handset.

The FLASH key doesn’t work. The wrong FLASH time is set. Change the setting of the FLASHtime.


GB - 36

No audio sound for PC calls � The audio device is not selected � Go to “Control Panel” and selectin the NOBLESSE VOIP phone. in Windows to “USB telephone” or “Sounds and Audio devices”.

“C-media USB headset”.· Select “Voice” accordingly. Check if the Voice playback. and recording are set to “C-media USB headset”.

� Skype™ doesn’t use the telephone � Open Skype™ and select “Tools” as audio device.· and “Options” accordingly.

Choose under “Privacy”-settings for “Manage other programs’ access to Skype™” and check if only NOBLESSE VOIP is shown.·

� The audio devices of Skype™ are � Open Skype™ and select “Tools” not set to the USB telephone. and “Options” accordingly. Check

under “Sound devices” if all devices are set to “C-media USB headset”.

The PC doesn’t give a sound The audio device for “Audio” is not Go to “Control Panel” and selectwhen you use other applications. correctly set in Windows for your “Sounds and Audio devices”.

PC-sound card. Select “Audio” accordingly. Checkif the sound playback andrecording is set for your PC-soundcard.

For more FAQ, please visit thecorresponding website (seepage 21).


GB - 37

IMPORTANT SAFETY MEASURES

• When you charge this product, a certain amount of heat will be produced.Do not put this product on antique, veneered or wooden surfaces to avoid damage.

• To avoid interference with other electronic appliances, such as a TV, radio or PC, you should place this product at least 1 meteraway.

• The effective range of this product is dependent on the local environment, such as building materials, the proximity ofdense trees, ponds, lakes or the sea.

• Do not use this product near water or in a damp environment, such as a bathroom.• Do not expose this product to fire, direct sunlight or intense heat.• For safety measures do not use this product near a gas-leak that you found and want to report.• Clean this product with a damp anti-static cloth.

Do not use fluid detergents or sprays.


Manuel Noblesse VOIP

Documents

Transcript of Manuel Noblesse VOIP