MALIN INTERNATIONAL SHIP REPAIR DRYDOCK, INC. · PDF fileMALIN INTERNATIONAL SHIP REPAIR &...

MALIN INTERNATIONAL SHIP

REPAIR & DRYDOCK, INC.

320 77TH Street

Galveston, TX 77554

Office: (409) 740‐3314

Fax: (409) 7218

www.malinshiprepair.com

Pier 41 Facilities

MISR’s main yard located in Galveston, TX is easily accessible via land and water and

offers a variety of amenities and services in a secure environment suitable for any

marine application. The facilities at Pier 41 include a 5,300 square foot covered

fabrication area, over 2,600 feet of available berthing space to 36 feet deep, 8 acres of

lay‐down area as well as private on‐site office space available for customer utilization.

Utilities conveniently located throughout the yard include freshwater, electrical, and

compressed air connections.

CERTIFICATIONS/CONTRACTS

Contract GS‐21F‐0148W

PROJECTS

US Government Contracts

Agency: US Coast Guard POC: Kyle Kagami

Telephone No: 409‐766‐5690 Vessel: USCGC Harry Claiborne

Period of Performance: 03/09/09‐03/20/09

Description of Work:

Install a new inclined ladder

Remove existing vertical ladder from 02 to 03 level

Install one (1) new aluminum inclined ladder

Remove sections of rail on 03 level in way of new inclined ladder

Install vertical stanchions to support free ends of rails

Perform non‐destructive testing (NDT) on all new welds

Agency: US Coast Guard POC: Albie D. Evans

Telephone No: 757‐628‐4665 Vessel: USCGC Harry Claiborne



Complete all welding and covering of cutter’s seabay system

Removed and replaced port and starboard Sea Chest vent lines and valves

Provided underwater videotaping of repair

Agency: Maritime Administration POC: Janice Marshall

Telephone No: 202‐366‐1744 Vessel: M/V “Barbara Lois”



Crop out, renew, and install a stern bulwark

Fender system on the bulwark

Fender system installed on the stern hull

Replace six (6) ballast vents on the stern of the vessel

Commercial Marine Repair

Agency: Well Ops – A Helix Company POC: Richard Scott

Telephone No: 281‐848‐6559 Vessel: Drilling Rig: Q‐4000



Replacement of two propulsion pods

Approximately 100 feet of 3” pipe

renewals

Mud pump piping renewals

Added gusset plates and stiffeners in

the moon pool

Double pads and pipe stanchions on

the MPT tower

Agency: REM Offshore POC: Arild Skram

Telephone No: +47 7008 08 95 Vessel: REM FORZA



Removal and installation of hull inserts

above summer load waterline utilizing

½”, 3/8” ABS plate and ½” X 6” flat bar.

Renew brackets connected between

tank top plate and side shell plate

between frames in ballast water tank.

Ultrasonic, dye, and vacuum box testing

of welds approved by DNV.

Repaired dented hull insert

Change vessel’s main crane rams

Agency: Canyon Offshore – A Helix Company POC: Danny Cook

Telephone No: 713‐996‐4020 Vessel: Northern Canyon



Assisted in the installation of trencher sub‐frame

Gussets, extension beam supports, and grating

Fabrication of access stairway to trencher platform

Removal of pads Installation of level wind and winch, and

Construction of frame for HPO unit Removed and reinstalled satellite dome Crane to haul container from stern of vessel

Installed aft port side and forward starboard wing walls into place

Sea fastened equipment.

Agency: CGG Veritas POC: Lenny Stanley

Telephone No: 835‐351‐8491 Vessel: CCG LAURENTIAN



Installed replacement starboard ships service diesel generator

Measurements performed to ensure the adequate coupling size

Machined coupling to fit the replacement generator and engine

Cut 5 x 5 opening in vessel side shell and through the tank bulkhead into the engine room to installed generator

Renewed side shell using 7/16” ABS plate in accordance with the owner’s direction

Agency: Western Geco POC: Lawrence Howard

Telephone No: 832‐868‐7172 Vessel:M/V STONES RIVER



Removed Containers and equipment Cut container foundations loose from deck

Added angles and flat bar to secure deck boards

Removed wire and wireways Cut down port and starboard exhaust

stacks

Installed rope guard after fabrication Reinstalled stainless steel bulwark

Welded and prepped for paint Removed fuel from tanks and stored in

order to perform hot work repairs

Fuel pumped back into tanks after hot work was completed

Agency: PGS Geophysical POC: Hans‐Peter Waldner

Telephone No: 281‐509‐8376 Vessel: M/V Ramform Valiant



Removal and installation of both

starboard and port side thrusters

Fabrication of antenna platform and

installation

Removal of twisted anchor chain from

locker

Renewal and fabrication of cooling pipe

and fittings

Repair of cracks and adding of stiffeners

in ballast tank bulkhead

Agency: Martin Midstream POC: Dwain Bankston

Telephone No: 281‐842‐3911 Vessel:M/V PONCIANA



Removed existing condenser and

refrigeration system

Fabrication of Cargo Piping Spools

Installed new cargo piping and exchangers

Marine Repair

Agency: Columbia University Lamont‐Doherty Earth Observatory

POC: Richard Beaudoin

Telephone No: 212‐854‐2331 Vessel:M/V MARCUS G. LANGSETH

Period of Performance: 3/16/2007‐ 9/02/2007


Removal and installation of gun rails

All star hydraulic work and welding

Repair of overhead in seismic lab

High seas net (Dome GPS) installation

Agency: Edison Chouest POC: Willie Danos

Telephone No: 985‐601‐4128 EXT: 51615 Vessel: M/V C‐LEGEND

Period of Performance: 04/2009


Performed work on ballast tank

Repaired cracked 8 ¾” ID x 14 ¾” OD

ballast pipe (overboard discharge line)

Installed double plate

Re‐welded both sides of bulkhead


Telephone No: 985‐601‐4128 EXT: 51615 Vessel: M/V GECO PEGASUS



Executed pipe work on CO2 system

Removal and installation of an 8 ft piece of

½ in galvanized pipe

Original piping was cut in half and

removed

New piping was cut and threaded in (2)

sections, then reinstalled with a ½ in union

Agency: Interocean American Shipping POC: Odd Helgas

Telephone No: 609‐502‐3732 Vessel: M/V HONOR



Removal of lagging and framing from

around base to access boiler

Repair cracks in lining

Reinstallation of lagging and framing

Repairs were also completed on the deck

lift

All star hydraulics were removed and

repaired

Removed and repaired clutch slave

cylinder for one of the deck lift trucks

Commercial Outside Machine/Fabrication

Agency: Crowley Maritime POC: Carly Remm

Telephone No: 904‐727‐2131 Vessel: M/V ATB RESOLVE



Removal of motor to pump couplings,

Drilling of locking set screws and

setting of mechanical seals

Reinstallation of couplings

Repaired and tested fire suppression

system

Removed, disassembled, and

reassembled system’s pneumatic

actuators

Removed and installed new cooler

from the starboard side aft engine

room overhead

Machining of aluminum engine covers

and in‐shop fabrication of new vacuum

tank.

Agency: Crowley Maritime POC: Trent Skladany

Telephone No: 904‐727‐2448 Vessel: Tug Integrity/Barge 650‐4



Removed heat exchanger

Fabricated heat blankets

Reinstalled new heat exchanger

Fabricated new insulation blankets at

MISR shop

Fabricated and installed copper nickel

spool pieces and supply and return

lines.


Telephone No: 985‐601‐4128 EXT: 51615 Vessel:M/V GECO PEGASUS

Period of Performance: December 2009


CO2 Pipework

removal and installation of 8 ft piece of ½

in galvanized pipe

cut and threaded new piping in (2) sections

Installed ½ in union

Agency: Odfjell POC: Rune Fanebust

Telephone No: +47 55 27 44 58 Vessel: M/V BOW PRIMA

Period of Performance: October 2008


Stern Tube Bearing Renewal

Controllable Pitch Propeller Repair

Tail Shaft Load Testing

Commercial Inside Machine/Fabrication


Telephone No: 985‐601‐4128 EXT: 51615 Vessel: M/V C‐PIONEER

Period of Performance:


Designed drilling fixture to allow the

drilling and tapping of a stripped out bolt‐

hole in stainless steel aft shaft coupling

Fabricated fixture and drilled and tapped

for larger 30mm bolts

machined opening in dog bones to

accommodate 30mm bolt

installed dog bone on shaft coupling

applied specified torque to coupling bolts

Agency: Secunda Marine Services POC:

Telephone No: 902‐463‐7678 Vessel: M/V BOLD ENDURANCE

Period of Performance: 8/18/08


Reconditioning of engine

Installation of new liner kits, rods, and

main bearings

Engine resealed with new gaskets and o‐

rings

Installation of oil pump, W‐water pump

and F‐water pumps

Agency: Gulf Sulphur Services POC:

Telephone No: 409‐765‐1206 Vessel: Turbine Sulfur Pump



Exterior Sandblasting of Turbine Pump

Bushing and seal Inspection

Fabrication of stainless steel pump shaft

Installed piping heat shield

Agency: Odfjell POC: Jan Magnus Hestdal

Telephone No: +47 55 27 45 42 Vessel:M/V BOW SPRING

Period of Performance: July 2008


Cylinder head resurfacing

Agency: Secunda Marine Services POC:

Telephone No: 902‐463‐7678 Vessel:M/V BOLD ENDURANCE



Fabricated (2) Stainless Steel Pump Shafts

(14 3/16 Long X 2.883 OD with 3” Long X

2.360 OD step and flanged end with 3 1/2”

holes drilled 120 degrees apart)

Phenolic Bushing Fabrication

Drilling and tapping of broken bolts

Agency: Seabulk Tankers, Inc. POC: Harvey J. Mott

Telephone No: 954‐627‐5259 Vessel: Seabulk Trader

Period of Performance: October 2009


Pressure Vacuum Valve Repair

Flame Screen Installation

PV Valve Repacking

Commercial Crane

Agency: Canyon Offshore – A Helix Company POC: Danny Cook

Telephone No: 713‐996‐4020 Vessel: Northern Canyon



Removed the launch and recovery system from vessel’s back deck

Reinstall level wind and trencher winch

Set containers on the ship’s deck that could not be reached by the vessel’s crane

Agency: Boa Marine Services POC: Tim Redland

Telephone No: 832‐466‐4250 Vessel: M/V BOA SUB C

Period of Performance: 2/5/2010 ‐


Mounted a 500 ton spool of wench cable to a shore‐side spooling apparatus

Utilized both 650 ton and 500 ton cranes in tandem

Agency: Con‐Dive POC: Kevin Bernard

Telephone No: 713‐591‐0556 Vessel:



Utilized 750 Ton shore crane to unload/load

100 Ton ship crane components

Fabricated 6 x 16 Lifting frame

Hoisted components and reel from dockside

to barge deck

Agency: PGS Geophysical POC: Hans‐Peter Waldner

Telephone No: 281‐509‐8376 Vessel: M/V RAM FORM VALIANT



Starboard and Port Side Thruster Removal/

Installation

Utilization of 500 Ton Crane

Agency: TTS Marine POC: Torsten Paas

Telephone No: +1 954 493 6405 Vessel:M/V CAP ORTEGAL



Crane Boom repair

Fabricated Boom Jig Fixture

Alignment Plate installation

Fabricated transition pieces and center

brace

Ultrasonic weld testing

Replaced (4) Pad eyes and (2) Sheaves

Applied Primer and Paint

Agency: Well Ops‐ A Helix Company POC: Richard Patton

Telephone No: 281‐848‐6559 Vessel: Drilling Rig: Q‐4000



Heavy lift of Propulsion Pods

Placed Pods shore‐side on prefabricated

cradles

Agency: Dockendale Shipping Company, LTD. POC: D’sa J. Eddy

E‐mail: [email protected] Vessel:M/V DS VANGUARD



Crane Pedestal Removal

Slewing Bearing Replacement

Jib Bearing replacement

Load Testing

Agency: Clipper Elite Carriers S.A. POC: Niels Giltrup

Telephone No: 713‐953‐2242 Vessel:M/V CARRIBEAN CARRIER

Period of Performance: March 2008


Removed/Reinstalled Crane Jib

Removed damaged sections of jib

Fabricated new jib sections

Ultrasonic weld testing

Crane and Jib load testing

Re‐spooled Crane Cable

Agency: Texas Department of Transportation POC:

Telephone No: Vessel:



Assisted the Texas Department of Transportation

incident response and recovery services up righting of overturned vehicles removal of large obstructions from

roadways removal of boats from the Galveston

Causeway

Agency: Western Geco POC: Keith Graham

Telephone No: 713‐689‐6589 Vessel: Geco Pegasus

Period of Performance: 2009‐Present


Provide crane service

Trash Removal

Load Vessel Supplies

Fabrication

Agency: Dow Chemical POC:

Telephone No: Project: Stainless Steel Pressure Vessel

Period of Performance:


Fabricated stainless steel pressure

vessel to the customer’s specs, within

the required timeline.

Agency: Tool Inc. POC: Cathy Busbey

Telephone No: Project: Mud Production Tanks

Period of Performance: September 2010


Constructed (3) mud production

tanks.

Utilized plate‐ roll to fabricate tank

walls.

Welded and pressure tested vessels

to customers standards.

Agency: Schlumberger Technology Corporation POC: Rod Shampine

Telephone No: 281-285-8479 Vessel:



Fabricated Pressure Vessel

Repaired and Modified existing Pressure

Vessels

Agency: Boa Marine Services POC: Tim Redland

Telephone No: 832‐466‐4250 Vessel:M/V BOA SUB C



Fabricated Spooling Tower Support Skid

Attached skid to Spooling Towers

Agency: Odfjell Management AS POC: Jan Magnus Hestdal

Telephone No: +47 55 27 45 42 Vessel:M/V BOW ATLANTIC

Period of Performance: June 2009


Fabricated Engine Room Vent Silencer

using 1/8” carbon steel plate rolled into

52.5” OD

Installed 2” of sound insulation

Sandblasted and coated 1/8” galvanized

perforated metal with zinc primer

Agency: Helix POC: Richard Patton




Fabricated 30 Ton 33’ X 33’ Carousel Base at

MISR yard

Coatings

Agency: Helix Energy Solutions POC: Richard Patton

Telephone No: No: 281‐848‐6559 Vessel: Q‐4000

Period of Performance: 10/15/10‐ 10/25/10


Coated 18” 90 degree pipe with flame sprayed

coating to extend overboard discharge piping

life.

Agency: Schlumberger Technology Corporation POC: Rod Shampine

Telephone No: 281-285-8479 Vessel:



Applied Powder‐Coating to Pressure Vessel

Agency: American Cargo Transport Corp. POC:

Telephone No: 206‐243‐1800 Vessel:M/V AMERICAN TRADER

Period of Performance: May 2009


Sandblasted (2) 11’ x 26’ and 11’ x 40’

cargo ramp doors

Applied (3) Coat Paint System (Bar‐Rust

235, Catha Coat 302, T‐10 Thinner)

Agency: Western Geco POC: Lawrence Howard

Telephone No: 832‐868‐7172 Vessel:M/V STONES RIVER



Prepping and painting in way of deck

boards wireways

Applied bulwark coating

Agency: Helix POC: Richard Patton




Sandblasting

Applied 3 part epoxy coating to carousel

base

Agency: Lott Ship Agency POC: Bill Lott

Telephone No: 251‐433‐1621 Vessel:M/V ACERGY POLAR QUEEN

Period of Performance: May 2009


Hydro‐blasted original paint from heli‐deck

Cleaned Prepped and laid out area to be

painted

Applied multiple paint coatings to heli‐

deck; approved by ship’s inspector

Agency: ID Wallem POC:

Telephone No: Vessel: OBELIX BULKER



Removed twisted rudder stock

Fabricated 10’ x 18’ x 20’ cofferdam

Installed cofferdam and inspected rudder

for damage

Machined new key way in rudder stock

Reinstalled rudder stock

Removed, aligned, and reinstalled steering

gear

Agency: Superior Energy POC: Nick Mayon

Telephone No: 337‐364‐9704 Vessel: DB Superior Performance

Period of Performance: Dec. 2010


De‐rig of SAT system

Disposed of vessel waste

Removal of fairleads, cow‐catchers, and

tender work

Provided logistics support

Installed equipment to make vessel ready

for Panama Canal passage

MALIN INTERNATIONAL SHIP REPAIR DRYDOCK, INC. · PDF fileMALIN INTERNATIONAL SHIP REPAIR &...

Documents

Transcript of MALIN INTERNATIONAL SHIP REPAIR DRYDOCK, INC. · PDF fileMALIN INTERNATIONAL SHIP REPAIR &...