MagellanTM 3200VSi · series, MagellanTM 8500 series, MagellanTM 9500 series, MagellanTM 9800i...

MagellanTM 3200VSiOmni-Directional Imaging Scanner

Quick Reference Guide

Datalogic ADC, Inc.959 Terry StreetEugene, OR 97402USATelephone: (541) 683-5700Fax: (541) 345-7140

© 2010 - 2013 Datalogic ADC, Inc.An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”). Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not remove or alter any proprietary notices, including copyright notices, contained in this documentation and shall ensure that all notices appear on any reproductions of the documentation.Should future revisions of this manual be published, you can acquire printed versions by contact-ing your Datalogic representative. Electronic versions may either be downloadable from the Data-logic website (www.datalogic.com) or provided on appropriate media. If you visit our website and would like to make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.

DisclaimerDatalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time with-out prior notice.Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. All other brand and product names may be trademarks of their respective owners.Magellan is a registered trademark of Datalogic ADC, Inc. in many countries, including the U.S.A. and the E.U.

This product may be covered by one or more of the following patents:Utility patents: EP1307854B1 ; EP1425704B1 ; GB2346474 ; GB2346475 ; US5481098 ; US5837983 ; US6012639 ; US6073849 ; US6129279 ; US6578765 ; US6705527 ; US6877663 ; US7201322 ; US7204422Additional patents pending.

Quick Reference Guide i

DATALOGIC ADC, INC. MAGELLANTM END USER LICENSE AGREEMENT

Notice to End User: The Datalogic Product you have acquired contains embedded Soft-ware, which is integral to the product's operation. This Software is being provided toyou under license, subject to the terms and conditions of this Agreement. If you use theDatalogic Product, you will be deemed to have accepted the terms and conditions of thisAgreement. If you do not intend to be bound to the terms of this Agreement, Datalogic isnot willing to license the Software to you, you may not use the Datalogic Product or theSoftware, and you must contact the party from whom you acquired the Datalogic Productfor instructions.

This End User Software License Agreement ("Agreement") is a legally binding agreement gov-erning the licensing of the Software and Documentation by Datalogic Holdings, Inc. and its sub-sidiaries and affiliates ("Datalogic") to the entity or person who has purchased or otherwiseacquired a Datalogic Product ("End User"). For purposes of this Agreement, any software thatis associated with a separate end-user license agreement is licensed to you under the terms ofthat license agreement. Datalogic and End User hereby agree as follows:

1. Definitions.

1.1 "Documentation" means materials such as user's guides, program reference guides,quick reference guides, manuals, or similar materials associated with or related to theDatalogic Product, whether in printed, "online", or other form.

1.2 "Proprietary Information" means: (a) source code, object code, software, documentation,and any related internal design, system design, data base design, algorithms, technol-ogy, technical data or information, implementation techniques, and trade secrets relatedto the Software, (b) any other trade secrets marked appropriately or identified as proprie-tary or confidential, and (c) any information that End User, under the circumstances,should recognize as confidential. Proprietary Information does not include any informa-tion that the receiving party can establish was (1) in the public domain, (2) already in thereceiving party's possession or rightfully known prior to receipt, (3) rightfully learned froma third party not in violation of any other's proprietary rights, or (4) independently devel-oped without access to Proprietary Information.

1.3 "Datalogic Product" means the Datalogic MagellanTM 800i, MagellanTM 1000i series,MagellanTM 1100i series, MagellanTM 1400i series, MagellanTM 2200VS series, Magel-lanTM 2300HS series, MagellanTM 3200VSi series, MagellanTM 3300HSi series, Magel-lanTM 8100 series, MagellanTM 8200 series, MagellanTM 8300 series, MagellanTM 8400series, MagellanTM 8500 series, MagellanTM 9500 series, MagellanTM 9800i series and/orMagellan SLTM series scanner and/or scanner/scale product, including all embeddedSoftware in and all Documentation related to such product, which has been purchased orotherwise acquired by End User, whether obtained directly or indirectly from Datalogic.

1.4 "Software" means any software or computer programs of Datalogic or its third party licen-sors in machine readable form which is embedded in the Datalogic Product, whetherobtained directly or indirectly from Datalogic, including any replacement, update,upgrade, enhancement or modification.

2. Scope Of License Granted.

2.1 Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to usethe Software, solely on the Datalogic Product in which it is embedded ("designated Data-logic Product"), in machine-readable form only, solely for End User's internal businesspurposes. This Agreement does not convey ownership of the Software to End User.Title to the Software shall be and remain with Datalogic or the third party from whom Dat-alogic has obtained a licensed right. As used in this Agreement, the term "purchase" orits equivalents when applied to the Software shall mean "acquire under license." EndUser is not entitled to receipt or use of the source code to any Software.

2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwisereproduce or remanufacture the Software, whether modified or unmodified, nor sell,assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to anyother person or organization, for purposes other than as expressly provided in this

ii MagellanTM 3200VSi

Agreement, without Datalogic's prior written consent.

3. Transfers, Support.

3.1 Any copying, installing, reproduction, remanufacture, reverse engineering, electronictransfer, or other use of the Software on other than the designated Datalogic Product willbe a material breach of this Agreement. However, Datalogic may elect not to terminatethis Agreement or the granted licenses, but instead may elect to notify End User that EndUser is deemed to have ordered and accepted a license for each breaching use. EndUser shall pay Datalogic the applicable list price for such licenses as of the date of suchbreach.

3.2 End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise trans-fer the Datalogic Product to any third party unless such third party agrees with Datalogicin writing to be bound by the terms and conditions of this Agreement. Any such transferof the Datalogic Product absent such agreement shall be null and void.

3.3 End User may obtain support for Software from Datalogic at Datalogic's standard sup-port fees and under Datalogic's standard support terms and conditions in effect at thetime the support is requested.

4. Intellectual Property.

End User acknowledges that the Software constitutes valuable trade secrets of Datalogic orDatalogic's third party licensors and that the Software is protected by intellectual property lawsand treaties. The license set forth in this Agreement does not transfer to End User any owner-ship of Datalogic's or its third party licensors' copyrights, patents, trademarks, service marks,trade secrets, or other intellectual property rights and End User shall have no right to com-mence any legal actions to obtain such rights. End User shall not remove, modify, or take anyother action that would obscure any copyright, trademark, patent marking, or other intellectualproperty notices contained in or on the Datalogic Product.

5. Proprietary Information.

5.1 End User acknowledges that Proprietary Information is the confidential, proprietary, andtrade secret property of Datalogic and Datalogic's third party licensors and End Useracquires no right or interest in any Proprietary Information.

5.2 End User shall not disclose, provide, or otherwise make available the Proprietary Infor-mation of Datalogic or its third party licensors to any person other than End User's autho-rized employees or agents who are under confidentiality agreement, and End User shallnot use the Proprietary Information other than in conjunction with use of the DatalogicProduct exclusively for End User's internal business purposes. End User shall takesteps to protect the Proprietary Information no less securely than if it were End User'sown intellectual property.

5.3 The provisions of this Proprietary Information Section shall survive and continue for five(5) years after the termination of this Agreement.

6. Limited Warranty.

6.1 Datalogic warrants that, under normal use and operation, the Datalogic Product will con-form substantially to the applicable Documentation for the period specified in the Docu-mentation. During this period, for all reproducible nonconformities for which Datalogichas been given written notice, Datalogic will use commercially reasonable efforts to rem-edy nonconformities verified by Datalogic. End User agrees to supply Datalogic with allreasonably requested information and assistance necessary to help Datalogic in reme-dying such nonconformities. For all defects reported to Datalogic within the warrantyperiod, Datalogic's liability is limited to providing End User with one copy of corrections orresponding to End User's problem reports according to Datalogic's standard assistancepractices. Datalogic does not warrant that the product will meet End User's requirementsor that use of the product will be uninterrupted or error free, or that Datalogic's remedialefforts will correct any nonconformance. This limited warranty does not cover any prod-uct that has been subjected to damage or abuse, whether intentionally, accidentally, or byneglect, or to unauthorized repair or unauthorized installation, and shall be void if EndUser modifies the product, uses the product in any manner other than as established inthe Documentation, or if End User breaches any of the provisions of this Agreement.

6.2 EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PRO-VIDED "AS IS" AND DATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESSOR IMPLIED, WRITTEN OR ORAL, WITH RESPECT TO THE PRODUCT, AND SPE-CIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND

Quick Reference Guide iii

FITNESS FOR A PARTICULAR PURPOSE.

7. Infringement.

7.1 Datalogic will defend End User against any claim in a lawsuit that the Datalogic Productfurnished hereunder infringe a United States patent or copyright of a third party and Dat-alogic will pay any damages finally awarded against End User by a court of competentjurisdiction that are attributable to such claim or will pay End User's part of any settle-ment that is attributable to such claim, provided, that 1) End User notifies Datalogicpromptly in writing of the claim, 2) Datalogic controls the defense or settlement of theclaim, and 3) End User cooperates fully with Datalogic in such defense or settlement. Allnotices of a claim should be sent to Datalogic Holdings, Inc., Legal Department, 959Terry Street, Eugene, OR 97402.

7.2 In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure forEnd User the right to continue using the Datalogic Product, 2) modify the Datalogic Prod-uct so that it becomes non-infringing, 3) replace the Datalogic Product with an equivalentproduct not subject to such claim, or 4) provide End User an opportunity to return theDatalogic Product and receive a refund of the purchase price paid, less a reasonableallowance for use.

7.3 Datalogic shall have no liability to End User for claims of infringement based upon 1) theuse of any Datalogic Product in combination with any product which Datalogic has noteither furnished or authorized for use with such Datalogic Product 2) the use of any Dat-alogic Product designed, manufactured, or modified to the specifications of End User, or3) End User's modification of the Datalogic Product without written authorization fromDatalogic.

7.4 THE FOREGOING STATES DATALOGIC'S COMPLETE AND ENTIRE OBLIGATIONCONCERNING CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUALPROPERTY INFRINGEMENT, CANCELS AND SUPERSEDES ANY PRIOR AGREE-MENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNINGSUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CON-TEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THEPARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTUREWRITING SIGNED BY BOTH PARTIES.

8. Limitation Of Liability.

EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANYCLAIMS AGAINST END USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'SLIABILITY FOR DAMAGES, IF ANY, WHETHER BASED UPON CONTRACT, TORT (INCLUD-ING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHERBASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PROD-UCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER ORANY THIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS ORSERVICE, OR FOR ANY OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT,INCIDENTAL, PUNITIVE, EXEMPLARY, OR OTHER SIMILAR DAMAGES, EVEN IF DATA-LOGIC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

9. Government Restricted Rights; International Use.

9.1 Use, duplication, or disclosure of the Software by the U.S. Government is subject to therestrictions for computer software developed at private expense as set forth in the U.S.Federal Acquisition Regulations at FAR 52.227-14(g), or 52.227-19 or in the Rights inTechnical Data and Computer Software clause at DFARS 252.227-7013(c)(1)(ii), which-ever is applicable.

9.2 If End User is using the Datalogic Product outside of the United States, End User mustcomply with the applicable local laws of the country in which the Datalogic Product isused, with U.S. export control laws, and with the English language version of this Agree-ment. The provisions of the "United Nations Convention on International Sale of Goods"shall not apply to this Agreement.

10. Termination.

10.1 Either party may terminate this Agreement or any license granted under this Agreementat any time upon written notice if the other party breaches any provision of this Agree-ment.

10.2 Upon termination of this Agreement, End User immediately shall cease using any non-embedded software and shall return to Datalogic or destroy all non-embedded software

iv MagellanTM 3200VSi

covered by this Agreement, and shall furnish Datalogic with a certificate of compliancewith this provision signed by an officer or authorized representative of End User. Forembedded software, End User agrees to sign a waiver prepared by Datalogic concerningfurther use of the embedded Software. End User's resumed or continued use of theembedded Software after termination shall constitute End User's agreement to be boundby the terms and conditions of this Agreement for such use.

11. General Provisions.

11.1 Entire Agreement; Amendment. This document contains the entire agreement betweenthe parties relating to the licensing of the Software and supersedes all prior or contempo-raneous agreements, written or oral, between the parties concerning the licensing of theSoftware. This Agreement may not be changed, amended, or modified except by writtendocument signed by Datalogic.

11.2 Notice. All notices required or authorized under this Agreement shall be given in writing,and shall be effective when received, with evidence of receipt. Notices to Datalogic shallbe sent to the attention of Contract Administration, Datalogic Holdings, Inc., 959 TerryStreet, Eugene, OR 97402, or such other address as may be specified by Datalogic inwriting.

11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agreementshall not prevent the party's later enforcement of such terms and conditions.

11.4 Governing Law; Venue: This Agreement and the rights of the parties hereunder shall begoverned by and construed in accordance with the laws of the State of Oregon U.S.A,without regard to the rules governing conflicts of law. The state or federal courts of theState of Oregon located in either Multnomah or Lane counties shall have exclusive juris-diction over all matters regarding this Agreement, except that Datalogic shall have theright, at its absolute discretion, to initiate proceedings in the courts of any other state,country, or territory in which End User resides, or in which any of End User's assets arelocated.

11.5 Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions ofthis Agreement, the prevailing party shall be entitled to reasonable attorneys' fees, bothat trial and on appeal.

- END -

Table of Contents

Quick Reference Guide v

China RoHS ................................................................................................. vi

Quick Reference......................................................................................... 1

Labeling and Nomenclature ................................................................. 1

Installation ................................................................................................... 2Power Supply ....................................................................................3

How to Scan ................................................................................................ 3

Troubleshooting........................................................................................ 4

Productivity Index Reporting™ Option.............................................. 5Scanner Push Button ......................................................................5

LED and Beeper Indicators..................................................................... 7

Error Codes .................................................................................................. 9

WEEE Statement ..................................................................................... 10

Going Green............................................................................................. 11

Bar Code Mask......................................................................................... 12

Programming .......................................................................................... 13

FCC Statement ........................................................................................ 16

Compliance Statement ........................................................................ 16

vi MagellanTM 3200VSi

China RoHS

PA

RT

部

件名

称

Lea

d

(Pb

) M

erc

ury

(H

g)

Ca

dmiu

m

(Cd

) H

exa

vale

nt

Chr

omiu

m

(Cr(

VI)

)

Pol

ybro

min

ate

d bi

ph

enyl

s (P

BB

)

Po

lyb

rom

ina

ted

d

iph

eny

l eth

ers

(PB

DE

)

有毒有

害物

质或元

素

铅

汞

镉

六价铬

多溴

联苯

多溴

二苯醚

P

owe

r su

pply

电

源

X

O

O

O

O

O

C

able

电

缆

X

O

O

O

O

O

P

CB

Ass

embl

y,

Bac

k Ill

umin

atio

n

印刷电

路板组装

，

后向照

明

X

O

O

O

O

O

P

CB

Ass

embl

y,

Mai

n

印刷电

路板组装

，主

板

X

O

O

O

O

O

P

CB

Ass

embl

y,

Con

tro

l Pan

el /

Illum

ina

tion

印刷电

路板组装

，

控制面

板/照

明

X

O

O

O

O

O

A

ssy,

Im

agin

g 组

装，

成像

X

O

O

O

O

O

A

ssy,

Mou

nt

Ris

er

支架组

件

X

O

O

O

O

O

O:

代表此

种部件

的所有均

质材

料中

所含的

该种有毒

有害物

质均低于

中华

人民共

和国信息

产业

部所颁

布的

《电子

信息产品

中有

毒有害

物质的限

量要

求》(SJ

/T 11363-2006) 规定的

限量

。

X:

代表

此种

部件所用

的均

质材料

中, 至少

有一

类材料

其所含的

有毒

有害

物质高

于中

华人民

共和国信

息产

业部所

颁布的

《电子

信息产品

中有

毒有害

物质的限

量要

求》(SJ

/T 11363-2006) 规定的

限量

EF

UP

de

term

ine

d b

y “L

ook-

up M

eth

od”

(sc

ann

er)

. 环

保使

用期

限取决

于“

查表

法”（扫

描仪

）

Quick Reference Guide 1

Quick ReferenceUse this guide to quickly complete your installation and begin using your scanner. For more details, including programming information, reference the Product Reference Guide (PRG), which is available for viewing and download from the Datalogic website listed on the back cover of this manual.

Labeling and Nomenclature

1. Back Cover 8. P/N Label

2. Scanner Push Button 9. USB/SD Cover

3. Camera Push Button 10. USB Test Port

4. Scan Window 11.SD Card Slot

5. Cable Connector Cover 12. Host (blue) Port

6. Checkpoint EAS Wire Cavity 13. Auxiliary (yellow) Port for handheld scanner, etc.

7. Serial Number/Regulatory Label

65

1

9

7

8 13121110

2

3

4

2 MagellanTM 3200VSi

InstallationConnect the scanner to the host (terminal) using the interface (I/F) cable as shown below. A cable from an older existing installa-tion can be re-used if it uses Power Off the Terminal (POT), unless it is a USB POT cable. If external power is used/needed, plug the AC Adapter into the AC wall outlet, then connect it to the I/F cable as shown in ‘b’ and ‘c’ of the illustration.

Scan some known-good bar code samples to verify correct opera-tion. The scanner should beep and/or flash its good read LED1 and send the bar code data to the host or terminal. If not, use the Troubleshooting section of this guide to identify any problems.

Scanner installation is complete.

1. Be aware that beeper and LED behavior may have previously been configured as “disabled” by another user.

USB

U

SB

RS-232

IB

M or...

or...

Terminal (PC)

To Terminal (PC)

To Terminal (PC)

Other Non-POT CablesPowered by AC Adaptervia short adapter cable

RS-232

a

b

c

Power Offthe Terminal(POT)

Keyboard Wedge, RS-232and USB Cables

Powered by AC Adapter

KeyboardWedge


Power SupplyModels require1 either a Listed class II or class III with a Limited Power Source (LPS). For the safety certification to be valid, class III input power sources must be IEC/EN60950-1 (EN 60335-series, EN 60065 or relevant) approved.

Input: 100 - 240 VAC Output: 12 VDCMax. Current: 1.5 A Max. Power: 18 W

How to ScanBar codes can either be presented to the scanner’s window or pushed past it using a “sweep” technique. The scanner can altena-tively be programmed to initiate a scan of a cell phone or other LCD bar code object, or an image capture upon pushing the Camera Push Button. See the PRG for more details.

1. Power Off the Terminal (POT) units do not require a power supply.

1. Product 4. Sweeping motion

2. Scan Window 5. Presentation motion

3. Bar code

1

2

3

45

1

2

3

Atención

Características de lafuente de alimentación

eléctrica.

Entrada: 100 - 240 Vca 600mA 50/60 HzSalida: +12 VDC 1500mA. (-) Negativo al centro

Utilice en su red solo fuentes certificadasen Argentina.El uso de fuentes de alimentación nocompatibles puede resultar en riesgo deincendio o de choque eléctrico para elusuario.


TroubleshootingUse this table to resolve common problems.

PROBLEM SOLUTION

Scanner does not power-onExchange the power supply with a known good power supply and retest operation.

No communication with the host

Consult your technical support personnel or refer to your host system manual to verify the proper interface type, cable and con-nection port(s) for the scanner. Verify the interface cable is securely attached to the host and the scanner.

The scanner will not read bar codes at all, or reads poorly

Make sure the window is clean. Check that the barcodes are of sufficient quality to be recognized by the scanner. Wrinkled, smudged, or torn labels can cause the scanner to not read at all. Scan known-good labels of an active symbologya to check the scanner's read operation.

a. Reading of the various barcode symbologies can be independently enabled or disabled in the scanner.

If the scanner still does not function properly, consult the Product Reference Guide (PRG) or contact your local supplier or Datalogic Customer Support Services.


Productivity Index Reporting™ Option

Your scanner may be equipped with the optional Productiv-ity Index Reporting™ feature. This feature allows for data collection on the readability index of bar codes scanned by the scanner. This data may be transmitted to the POS Ter-minal where it may be easily sorted for action by the MIS department to improve bar code quality at the front end.For additional information on how to enable Productivity Index Reporting in your scanner, please refer to the Product Reference Guide (PRG)

Scanner Push ButtonThe Scanner Push Button also performs multiple functions depending upon the duration of time it is pressed:

NOTE

Volume changes made using the Volume/Tone PushButton are lost when the scanner is powered-downand are reset to the configured setting. If you wish topermanently change the volume, use the specialprogramming labels in the Product Reference Guide.

Table 1. Scanner Push Button Functions

PRESSDURATION

FUNCTION COMMENT

Momentary (when scanner is asleep)

Wakes scanner from Sleep Mode

Alternatively, the scanner can be awakened by:- Moving an object through the scan zone.- Scanning with an attached aux-iliary scanner.


Momentary (when scanner is awake)

Increments volume

Press the push button momen-tarily to increase speaker vol-ume. When the loudest volume is reached, a repeated press of the push button cycles volume back to the lowest setting, then volume increases on subsequent press(es). Four volume levels are available.

Hold, then release when the beeper sounds

Increments tone

Press the push button for approximately 2 seconds, then release. Each time this is done, the beeper will sound at one of three tones. Stop when the desired tone (high, medium or low) is sounded.

4 SecondsScanner Diagnostics Modea

This mode allows system sup-port personnel to troubleshoot problems with the scanner and is used to determine if it can read bar codes. Press the button for eight seconds or cycle power to exit Scanner Diagnostics Mode and reset the scanner.

8 Seconds Resets Scannerb Only system support personnel should perform a reset.

a. By standard default, this function is normally disabled to prevent accidental activation by users.

b. Users should not perform scanner resets except under the direction of trained systems support personnel.

Table 1. Scanner Push Button Functions

PRESSDURATION

FUNCTION COMMENT


LED and Beeper IndicatorsThe scanner’s beeper sounds and its green LED illuminates to indicate various functions or errors on the scanner. The tables below list these indications. An exception to the behaviors listed in the tables is that the scanner’s functions are programmable, and may or may not be turned on. For example, certain indica-tions, such as the power-up beep can be disabled using program-ming barcode labels.

Table 2. Green LED Indications

LED INDICATION

INDICATION COMMENT

Power-on indication

Bright green flashIndicates the scanner has finished all its power up tests and is now ready for operation.

Good ReadIndication

Bright green flashIndicates a barcode has been read and decoded.

Scanner Ready

Constant dim green The scanner is ready for operation.

Sleep Mode

Green LED slowly and continuously changes from off to dim to off.

The scanner is in Sleep Mode. To wake the scanner up, move an object in front of its window or press the button atop the unit. This indication is optionally configurable, and may have been pro-grammed to behave differently.

Host Disable

Constant green flash at 1 Hz (100mS on, 900mS off)

The scanner is disabled due to receiv-ing a disable command from the POS terminal.


Diagnostics

Varies (see Error Codes on page 9 for more informa-tion)

The LED can provide diagnostic feed-back if the scanner discovers a prob-lem during SelfTest.

Prog. ModeSee Host Disable above.

The scanner is in Programming Mode.

Table 3. Beeper Functions

BEEPER INDICATION

INDICATION COMMENT

Power On Beep Single beep

The Power-On LED indication is a config-urable feature which can be enabled or disabled. When enabled, this beep indi-cates the scanner has finished all its power up tests and is now ready for oper-ation.

Good ReadIndication

Single beep

The good read beep indication is configu-rable. Options include: Enable/disable, frequency, duration and volume. See the Product Reference Guide (PRG) for more information.

Diagnostics

Varies (see Error Codes on page 9 for more informa-tion)

The Beeper can provide diagnostic feed-back if the scanner discovers a problem during SelfTest.

Programming Mode Indications

Varies depending upon the fea-ture(s) being con-figured.

The Beeper will sound as programming barcode labels are scanned, indicating progress during scanner configuration.

Table 2. Green LED Indications

LED INDICATION

INDICATION COMMENT


Error CodesIf an error is detected, the scanner will sound a long low tone (for three seconds) and flash its LED, indicating a failure. When this occurs, press the Scanner Push button to hear the error code. If it is configured to do so, the scanner will sound a series of beeps corresponding to the error code and/or flash its LED simultane-ous to the beeps. The table below describes what these codes mean and what action should be taken for each.

NUMBER OF LED FLASHES/

BEEPSERROR CORRECTIVE ACTION

1 Configuration

Contact Helpdesk for assistance

2 Interface PCB

4 Imager

6 Main PCB

10 Button Error

11 Hardware ID

12 Model ID

13 CPLD ID


WEEE Statement

EnglishFor information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.datalogic.com.

ItalianPer informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.datalogic.com.

FrenchPour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet www.datalogic.com.

GermanInformationen zur Entsorgung von Elektro- und Elektronik- Altgeräten (WEEE) erhalten Sie auf der Webseite www.datalogic.com.

SpanishSi desea información acerca de los procedimientos para el desecho de los residuos del equipo eléctrico y electrónico (WEEE), visite la página Web www.datalogic.com.

PortuguesePara informações sobre a disposição de Sucatagem de Equipamentos Elétricos e Eletrônicos (WEEE -Waste Electrical and Electronic Equipment), consultar o site web www.datalogic.com.

Chinese有关处理废弃电气电子设备 (WEEE) 的信息，请参考 Datalogic 公司的网站www.datalogic.com/。

Japanese廃電気電⼦機器 (ＷＥＥＥ) の処理についての関連事項は Datalogic のサイト www.datalogic.com をご参照下さい。

Waste Electrical and Electronic Equipment (WEEE) Statement


Going GreenThank you for using the bar code mask on the opposite side of this page. This manual has been formatted to minimize the quan-tity of pages needed to provide all of the programming bar codes available for this product.


Bar Code Mask

Cut a hole in this page and remove it from the manual as indicated to create a sleeve through which bar codes (start-ing on the following page) can be individually viewed and scanned. It is important that only one bar code at a time be presented to the scanner.

1

2

3

1. Bar Code Mask Sheet 3. Manual (folded)

2. Bar Code


ProgrammingUpon completing the physical connection between the reader and its host, proceed directly to the Programming Bar Codes table below to locate the interface type the reader is connected to (for example: RS-232, Keyboard Wedge, USB, etc.).

Use the Bar Code Mask on the preceding page to isolate the bar code you intend to scan. Scan a Start/End bar code once to enter Programming Mode. After selecting (scanning) the interface, scan the ENTER/EXIT barcode a second time, which will then accept your changes, exit Programming Mode and return the reader to normal operation.

You can select other options and customize your reader through use of the instructions and programming barcodes available in the PRG or use the On Screen Programming (OSP) utility available from the website listed on the back cover of this manual.

START / END

PROGRAMMING BAR CODES

RS-232 Standard

RS-232 Wincor-Nixdorf


IBM 4683 Port 5B

IBM 4683 Port 9B

IBM 4683 Port 17

USB-OEM

START / END


USB Keyboard

USB COM Interface

Keyboard Wedge A (PC/XT w/alternate Key Encoding)

NOTE

If other than Keyboard Wedge A with USAkeyboard is needed, see the PRG or OnScreen Programming for additional options.

START / END


FCC StatementThis Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa-tion. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter-ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which receiver is connected

• Consult the dealer or an experienced radio / TV technician for help.

Compliance StatementThis Class B digital apparatus complies with Canadian ICES -003.Cet appareil numérique de la classe B est confrome à la norme NMB-003 duCanada.

LED ClassCLASS 1 LED PRODUCT APPARECCHIO LED CLASSE 1LED KLASSE 1 APPAREIL A LED DE CLASSE 1

IEC / EN 60825-1:2007Max output of LED radiation: 3.21mW per pulse at 100mmPulse duration: 200usEmitted wavelength 625nm

CAUTION

The User is cautioned that changes or modifi-cations not expressly approved by the partresponsible for compliance could void theuser’s authority to operate the equipment.


WarrantyDatalogic warrants to Customer that this product will be free from defects in materials and workmanship for a period of 3 years from product shipment.

Datalogic ADC Limited Factory Warranty

Warranty CoverageDatalogic ADC (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use. The liability of Datalogic under this war-ranty is limited to furnishing the labor and parts necessary to remedy any defect covered by this warranty and restore the product to its normal operating condition. Repair or replacement of product during the warranty does not extend the original warranty term. Products are sold on the basis of specifications applicable at the time of manufacture and Datalogic has no obligation to modify or update products once sold.If Datalogic determines that a product has defects in material or workmanship, Datalogic shall, at its sole option repair or replace the product without additional charge for parts and labor, or credit or refund the defective products duly returned to Datalogic. To perform repairs, Datalogic may use new or reconditioned parts, components, subassemblies or products that have been tested as meeting applicable specifications for equivalent new material and products. Customer will allow Datalogic to scrap all parts removed from the repaired product. The warranty period shall extend from the date of shipment from Data-logic for the duration published by Datalogic for the product at the time of purchase (War-ranty period). Datalogic warrants repaired hardware devices against defects in workmanship and materials on the repaired assembly for a 90 day period starting from the date of shipment of the repaired product from Datalogic or until the expiration of the origi-nal warranty period, whichever is longer. Datalogic does not guarantee, and it is not responsible for, the maintenance of, damage to, or loss of configurations, data, and appli-cations on the repaired units and at its sole discretion can return the units in the “factory default” configuration or with any software or firmware update available at the time of the repair (other than the firmware or software installed during the manufacture of the prod-uct). Customer accepts responsibility to maintain a back up copy of its software and data.

Warranty Claims ProcessIn order to obtain service under the Factory Warranty, Customer must notify Datalogic of the claimed defect before the expiration of the applicable Warranty period and obtain from Datalogic a return authorization number (RMA) for return of the product to a designated Datalogic service center. If Datalogic determines Customer’s claim is valid, Datalogic will repair or replace product without additional charge for parts and labor. Customer shall be responsible for packaging and shipping the product to the designated Datalogic service center, with shipping charges prepaid. Datalogic shall pay for the return of the product to Customer if the shipment is to a location within the country in which the Datalogic service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations. Failure to fol-low the applicable RMA policy, may result in a processing fee. Customer shall be responsi-ble for return shipment expenses for products which Datalogic, at its sole discretion, determines are not defective or eligible for warranty repair.

Warranty ExclusionsThe Datalogic Factory Warranty shall not apply to:


(i) any product which has been damaged, modified, altered, repaired or upgraded by other than Datalogic service personnel or its authorized representatives;

(ii) any claimed defect, failure or damage which Datalogic determines was caused by faulty operations, improper use, abuse, misuse, wear and tear, negligence, improper storage or use of parts or accessories not approved or supplied by Dat-alogic;

(iii) any claimed defect or damage caused by the use of product with any other instrument, equipment or apparatus;

(iv) any claimed defect or damage caused by the failure to provide proper mainte-nance, including but not limited to cleaning the upper window in accordance with product manual;

(v) any defect or damage caused by natural or man-made disaster such as but not limited to fire, water damage, floods, other natural disasters, vandalism or abu-sive events that would cause internal and external component damage or destruction of the whole unit, consumable items;

(vi) any damage or malfunctioning caused by non-restoring action as for example firmware or software upgrades, software or hardware reconfigurations etc.;

(vii) the replacement of upper window/cartridge due to scratching, stains or other degradation and/or

(viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads, touch screen, triggers etc.).

No AssignmentCustomer may not assign or otherwise transfer its rights or obligations under this war-ranty except to a purchaser or transferee of product. No attempted assignment or transfer in violation of this provision shall be valid or binding upon Datalogic.DATALOGIC'S LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, ORAL OR WRITTEN, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITA-TION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NONINFRINGEMENT. DATALOGIC SHALL NOT BE LIABLE FOR ANY DAMAGES SUSTAINED BY CUSTOMER ARISING FROM DELAYS IN THE REPLACEMENT OR REPAIR OF PRODUCTS UNDER THE ABOVE. THE REMEDY SET FORTH IN THIS WARRANTY STATEMENT IS THE CUSTOMER’S SOLE AND EXCLUSIVE REMEDY FOR WARRANTY CLAIMS. UNDER NO CIRCUMSTANCES WILL DATALOGIC BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CON-TINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

Risk of LossCustomer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic’s possession. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.

This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC, Inc. and hereby declares that the apparatus specified below has been tested and found compliant to the following European Council Directives and Harmonized Standards:

A technical construction file for this apparatus is retained at the above Datalogic ADC, Inc. address.

EquipmentType:

Barcode Scanning Equipment

Apparatus: Magellan 3200VSi and Magellan 3300HSiManufactured

by:Datalogic ADC, Inc.959 Terry St. Eugene, OR USA Ph: 541-683-5700

Datalogic Slovakia s.r.o.Prilohy 588/47919 26 Zavar, Slovakia, Ph: 421 33 590 8970

Datalogic Scanning Vietnam LLC.Lot I-4b Saigon High Tech Park,Dist. 9 Ho Chi Minh City, Ph: 84 837 30 8481

Placed into EUService: June 16, 2010, Declaration updated April 2013

CouncilDirectives:

EMC 2004/108/ECLow Voltage 2006/95/ECRoHS 2011/65/EC (8 June 2011)WEEE 2002/96/EC

Standards: EN 55022: 2006,A1:2007AZ/NZS CISPR22:2009EN 55024:1998,A1:2001,A2:2003EN 61000-3-2:2006EN 6100-3-3:1995,A1:2001,A2:2005EN 60950-1:2006, A11:2009+ A1:2010 + A12:2011

EN 60825-1:2007EN 50581:2012

Generic EmissionGeneric EmissionGeneric Immunity - ITEHarmonic Current

Voltage Fluctuation/Flicker

Safety of Information Tecnology EquipmentSafety of Laser/LED ProductsTechnical Documentation for the Assessment of EEE w.r.t. RoHS

EUROPEAN DECLARATION OF CONFORMITY

April 03, 2013Brad West Vice President Global Supply Chain OperationsDatalogic ADC, Inc.

EC-089 Rev.: 2

820055014 (Rev. C) June/2013

www.datalogic.com

© 2010-2013 Datalogic ADC, Inc. • All rights reserved. • Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U.

Datalogic ADC, Inc.959 Terry Street | Eugene |OR 97402 | USATelephone: (1) 541-683-5700 | Fax: (1) 541-345-7140

http://www.datalogic.com

MagellanTM 3200VSi · series, MagellanTM 8500 series, MagellanTM 9500 series, MagellanTM 9800i...

Documents

Transcript of MagellanTM 3200VSi · series, MagellanTM 8500 series, MagellanTM 9500 series, MagellanTM 9800i...