LIGNA S 38 ST x M
1
Data Sheet Access Floor Type Ligna S 38 ST x M 1 Access floor panel with galvanized steel sheet at bottom side 2 Plastic edge trim 3 Pedestal glue 4 Height fixing 5 Gasket Technical Data Point load 1 5 kN Building material class of panel 2 B2 Fire resistance class 3 F 30 Electrostatic conductivity 4 ≥ 10 6 Ω Weight of system 5 30 kg/m² Finished floor heights (FFH) 6 70 – 1250 mm Panel thickness 38,5 mm Pedestal spacing 600 mm 1 test acc. to RAL-GZ 941, meassuring point in the centre of panel 2 B1 on request 3 acc. to DIN 4102, up to 500 mm floor heights, bigger heights with special measures 4 values depending on floor covering 5 floor height 150 mm (FFH), without covering 6 special heights on request acoustic values acc. to DIN 52210 without covering with covering normalized flanking level difference RL,w,P 49 dB 52 dB (VM=28 dB) sound reduction index Rw,P 62 dB - reduction of impact sound pressure level ΔLw,P 16 dB - System Description Panel special high density chipboard panel classified E1, steel sheet at bottom, surrounding edge trim protection against damage and humidity, edges inclined Pedestal precisely height adjustable, from galvanized and yellow chromatized steel, precision threaded bolt, various types according to height requirements Gasket from conductive plastic material, vaulted surface for perfect panel fixing Height fixing securing part or locking glue (alternatively) Pedestal glue placing of pedestal base into pedestal glue Finished floor heights >500 mm use of stringers is recommended for better lateral stability Wall connection pre-compressed foam rubber, as sound barrier and absorption of horizontal movements Subfloor a 2-component epoxy coating is recommended in case of air ventilation normalized flanking impact sound pressure level Ln,w,P 64 dB 52 dB (VM=25 dB) Application Possible Floor Coverings computer rooms and control rooms industry and working rooms training and research rooms office and construction areas linoleum, rubber, PVC, HPL parquet tufting, velour, needlefelt loosely laid covering tiles Access Floor Type Ligna S 38 ST x M page 1 of 1 Rev. 01, 03/2006 Lindner AG, Bahnhofstr. 29, D - 94424 Arnstorf, phone +49 (0) 87 23 / 20-0, fax +49 (0) 87 23 / 20-21 47, www.lindner-holding.de, [email protected] Subject to change without notice. This document is our intellectual property. This document shall not be copied, unauthorised used or distributed for trade or presented to third parties.
-
Upload
mohamed-hassan -
Category
Documents
-
view
275 -
download
2
Transcript of LIGNA S 38 ST x M
Data Sheet
Access Floor Type Ligna S 38 ST x M
1 Access floor panel with galvanized steel sheet at bottom side
2 Plastic edge trim
3 Pedestal glue
4 Height fixing
5 Gasket
Technical Data Point load
1 5 kN
Building material class of panel2 B2
Fire resistance class3 F 30
Electrostatic conductivity4 ≥ 10
6 Ω
Weight of system 5 30 kg/m²
Finished floor heights (FFH)6 70 – 1250 mm
Panel thickness 38,5 mm
Pedestal spacing 600 mm
1 test acc. to RAL-GZ 941, meassuring point in the
centre of panel 2 B1 on request
3 acc. to DIN 4102, up to 500 mm floor heights,
bigger heights with special measures 4 values depending on floor covering
5 floor height 150 mm (FFH), without covering
6 special heights on request
acoustic values acc. to DIN 52210
without covering
with covering
normalized flanking level difference RL,w,P
49 dB 52 dB (VM=28 dB)
sound reduction index Rw,P
62 dB -
reduction of impact sound pressure level ∆Lw,P
16 dB -
System Description
Panel special high density chipboard panel classified E1, steel sheet at bottom, surrounding edge trim protection against damage and humidity, edges inclined
Pedestal precisely height adjustable, from galvanized and yellow chromatized steel, precision threaded bolt, various types according to height requirements
Gasket from conductive plastic material, vaulted surface for perfect panel fixing
Height fixing securing part or locking glue (alternatively)
Pedestal glue placing of pedestal base into pedestal glue
Finished floor heights >500 mm use of stringers is recommended for better lateral stability
Wall connection pre-compressed foam rubber, as sound barrier and absorption of horizontal movements
Subfloor a 2-component epoxy coating is recommended in case of air ventilation
normalized flanking impact sound pressure level Ln,w,P
64 dB 52 dB (VM=25 dB)
Application Possible Floor Coverings computer rooms and control rooms industry and working rooms training and research rooms office and construction areas
linoleum, rubber, PVC, HPL parquet tufting, velour, needlefelt loosely laid covering tiles
Access Floor Type Ligna S 38 ST x M page 1 of 1 Rev. 01, 03/2006
Lindner AG, Bahnhofstr. 29, D - 94424 Arnstorf, phone +49 (0) 87 23 / 20-0, fax +49 (0) 87 23 / 20-21 47, www.lindner-holding.de, [email protected]
Su
bje
ct
to c
ha
nge
with
ou
t n
otice
.
Th
is d
ocum
en
t is
ou
r in
telle
ctu
al p
rop
ert
y. T
his
do
cu
me
nt
sh
all
no
t b
e
co
pie
d,
un
au
tho
rise
d u
se
d o
r d
istr
ibu
ted f
or
tra
de
or
pre
se
nte
d t
o
thir
d p
art
ies.
