Lec. 3 Mat. Cements
-
Upload
sarah-kahil -
Category
Documents
-
view
227 -
download
0
Transcript of Lec. 3 Mat. Cements
-
7/29/2019 Lec. 3 Mat. Cements
1/40
Dental Materials
Types Of the Cements
Introduction
-
7/29/2019 Lec. 3 Mat. Cements
2/40
Silicate Cements
Silicate cements were introduced in 1903 asanterior esthetic filling materials. They aretranslucent .
Silicates are attacked by oral fluids and in timedegrade. The average life of a silicaterestoration is four years.
1- 25 years. Silicates are rarely used nowadays. This is due
to development of better materials likecomposite resin and glass ionomer cements.
-
7/29/2019 Lec. 3 Mat. Cements
3/40
Applications
Esthetic restoration of anteriorteeth
Intermediate restoration incaries active mouths.
-
7/29/2019 Lec. 3 Mat. Cements
4/40
Anticariogenic Properties
The anticariogenic property is due to presenceof 15% flouride. Flouride release is slow andoccurs throughout the life of the restoration.
Mech. Of anticariogenic effect are :
It makes the adjacent tooth structure moreresistant to acid decalcification.
It acts as an antibacterial agent. It acts as anenzyme inhibitor and thus prevents themetabolism of carbohydrates.
-
7/29/2019 Lec. 3 Mat. Cements
5/40
Zinc Phosphate Cement
Applications :
Luting of restorations (cementation)
High strength bases Temporary restorations
Luting of orthodontic bands and
brackets.
-
7/29/2019 Lec. 3 Mat. Cements
6/40
Classification: Type - I: Fine grained for luting, Film
thickness should be 25 um or less. Type-II : Medium grain for luting and
filling, Film thickness should not be morethan 40 urn.
Available As Powder and liquid system . Capsules of preproportioned powder and
liquid.
-
7/29/2019 Lec. 3 Mat. Cements
7/40
Composition
Powder Zinc oxide 90.2%
Principal constituent
Magnesium oxide 8.2%Aids in sintering Other oxides (like bismuth trioxide, calcium oxide, barium oxide,
etc.) 0.2%
Improves smoothness of mix Silica 1.4%
Filler, aids in sintering
-
7/29/2019 Lec. 3 Mat. Cements
8/40
Liquid
Phosphoric acid 38.2%Reacts with zinc oxide
Water 36.0%
Controls rate of reaction
Aluminium phosphate or sometimes zincphosphate 16.2%
Buffers, to reduce rate of reaction Aluminium 2.5%
Zinc 7.1%.
-
7/29/2019 Lec. 3 Mat. Cements
9/40
Setting Time5 to 9 minutes
Control of Setting Time by:
-
7/29/2019 Lec. 3 Mat. Cements
10/40
A/ Manufacturing process:
1. Sintering temperature: The higher thetemperature, the more slowly the cement sets.
2. Particle size: Finer particles react more
quickly as a greater surface area is exposed tothe liquid.
3. Water content of liquid: Presence of excesswater accelerates, whereas insufficient water
retards the reaction.4. Buffering agents: When added slow down
the reaction.
-
7/29/2019 Lec. 3 Mat. Cements
11/40
B/ Factors under control of operator:
Temperature: Higher temperaturesaccelerate the reaction
P/L ratio: More the liquid, slower the
reaction Rate of addition of powder to liquid: the
reaction is slower if the powder is
incorporated slowly. Mixing time: The longer the mixing time
(within practical limits), the slower is therate of reaction
-
7/29/2019 Lec. 3 Mat. Cements
12/40
Properties
Compressive Strength : Zinc phosphate cementis stronger (103.5 MPa) than zinc oxide-eugenolcement but not as strong as silicophosphate. Theset cement gains 75% of its maximum strength in
the first hour. Maximum strength is attained in thefirst day.
The strength of zinc phosphate cement issufficient when used as a base or luting agent.
However, when it is exposed to the oralenvironment, e.g. temporary restorations, itsbrittleness and low strength causes it to fractureand disintegrate.
-
7/29/2019 Lec. 3 Mat. Cements
13/40
Modulus of Elasticity :It is comparatively high . This
makes it stiff and resistant to elasticdeformation. This is necessary when itis employed as a luting agent for
restorations that are subjected to highmasticatory stresses.
-
7/29/2019 Lec. 3 Mat. Cements
14/40
Solubility and Disintegration : This property is
important for cements used for permanentcementation., it shows low solubility (0.06% Wt).
However, in the mouth they show greaterdisintegration over a period of time. This shows
that other factors are involved .
Film Thickness :
For Type I - Film thickness not more than 25 um ,
for Type II - Film thickness not more than 40 um.
-
7/29/2019 Lec. 3 Mat. Cements
15/40
-
7/29/2019 Lec. 3 Mat. Cements
16/40
Thermal Properties: Zinc phosphatecements are good thermal insulators
and may be effective in reducinggalvanic effects.
Adhesion Property : The retention of acemented restoration is by mechanical
interlocking of the set cement withsurface roughness of the cavity andrestoration.
-
7/29/2019 Lec. 3 Mat. Cements
17/40
Biological Properties : Pulp response-moderate. The acidity is high at the time ofinsertion . Three minutes after mixing, thepH is 3.5. It approaches neutrality in 24 to48 hours.
A thickness of dentine as great as 1.5mm can be penetrated by the acid of thecement. If dentine is not protected againstinfiltration of this acid, pulpal injury mayoccur, especially during the first few hours.Pulp protection In deep cavities is needed
Optical Properties :The set cement isopaque.
-
7/29/2019 Lec. 3 Mat. Cements
18/40
Manipulation :
Spatula used Stainless steel. Mixing time 1min. 15 seconds.
Powder-Liquid Ratio: 1.4 gm/O.5 ml :A cool glass slab is used in order to delaythe setting and allow more powder to be
incorporated before the matrix formationoccurs. The liquid should be dispensed justbefore mixing.
-
7/29/2019 Lec. 3 Mat. Cements
19/40
Procedure
-
7/29/2019 Lec. 3 Mat. Cements
20/40
Maximum amount of powder should beincorporated in the liquid to ensure minimumsolubility and maximum strength. Note: An
appropriate consistency is attained by addition ofmore powder to the liquid and not by allowing athin mix to thicken.
-
7/29/2019 Lec. 3 Mat. Cements
21/40
Insertion
The crown should be seatedimmediately and held underpressure till set. Field of operation
should be dry. Varnish is appliedat the margins, where the cementis exposed.
-
7/29/2019 Lec. 3 Mat. Cements
22/40
Zinc Oxide-Eugenol Cement
These cements have been used extensivelyin dentistry since the 1890's. Depending ontheir use they vary widely in theirproperties.
To improve the strength many modifiedzinc oxide-eugenol cements have beenintroduced, e.g. EBA-alumina modified andpolymer-reinforced zinc oxide-eugenolcements.
Recently non-eugenol zinc oxide cementshave become available. They are suitablefor patients sensitive to eugenol
-
7/29/2019 Lec. 3 Mat. Cements
23/40
Classification: 4 Types
Type I ZOE - For temporary
cementation . Type Il ZOE - Permanent cementation
.
Type III ZOE - Temporary filling andthermal insulation .
Type IV ZOE - Cavity liners .
-
7/29/2019 Lec. 3 Mat. Cements
24/40
Composition
Powder Zinc oxide 69.0% Principal
ingredient
White rosin 29.3% To reducebrittleness of set cement Zinc stearate 1.0% Accelerator,
plasticizer Zinc acetate 0.7% Accelerator,
improves strength Magnesium oxide Is added in some
powders, acts with eugenol in a similarmanner as zinc oxide.
-
7/29/2019 Lec. 3 Mat. Cements
25/40
Liquid
Eugenol 85.0 Reacts with zinc
oxide
Olive oil 15.0 Plasticizer.
-
7/29/2019 Lec. 3 Mat. Cements
26/40
Setting Reaction
ZnO + H20 Zn(OH)2
Zn(OH)2 + 2HE ZnE2 + 2H20
Base Acid Salt(Zinc hydroxide) (Eugenol) (Zinc eugenolate)
-
7/29/2019 Lec. 3 Mat. Cements
27/40
Setting Time 4-10 minutes. Thecomplete reaction between zinc oxide
and eugenol takes about 12 hours.This is too slow for clinicalconvenience.
-
7/29/2019 Lec. 3 Mat. Cements
28/40
Factors Affecting Setting Time
1. Manufacture: The most active zinc oxide powdersare those formed from zinc salts like zinc hydroxideand zinc carbonate by heating at 3000C.
2.Particle size: Smaller zinc oxide particles set faster.
3.Accelerators: Alcohol and water.4.Heat: Cooling the glass slab, slows the reaction.
5.Retarders: The set can be retarded with glycol andglycerine
6.Powder to liquid ratio: Higher the ratio, faster theset.
-
7/29/2019 Lec. 3 Mat. Cements
29/40
Properties:Mechanical Properties
Compressive strength:. They arerelatively weak cements. The strength
depends on what it is used for. The compressive strength therefore ranges
from a low of 3 to 4 MPa upto 50-55 MPa.Particle size affects the strength.
In general, the smaller the particle size,the stronger the cement. The strength canalso be increased by reinforcing withalumina-EBA or polymers
-
7/29/2019 Lec. 3 Mat. Cements
30/40
Tensile strength: Ranges from 0.32 to5.3 MPa.
Modulus of elasticity This is animportant property for those cementsintended for use as bases.
-
7/29/2019 Lec. 3 Mat. Cements
31/40
Thermal Properties are approximately thesame as for human dentin
Solubility and Disintegration :Thesolubility of the set cement is highest
among the cements (0.4% wt). Theydisintegrate in oral fluids. This break downis due to hydrolysis of the zinc eugenolatematrix to form zinc hydroxide and eugenol.
Solubility is reduced by increasing the P/Lratio ..
-
7/29/2019 Lec. 3 Mat. Cements
32/40
Film Thickness : The film thicknessof zinc oxide-eugenol cements (25um) is higher than other cements.
Adhesion :They do not adhere well toenamel or dentin. This is one reasonwhy they are not often used for finalcementation of crowns and bridges.
The other reasons are low strengthand high solubility.
-
7/29/2019 Lec. 3 Mat. Cements
33/40
Biological Properties : pH and
effect on pulp: (pH is 6.6 to 8.0). Theyare the least irritating of all cements.
the Bacteriostatic and obtundant
properties: They inhibit the growth ofbacteria and have soothing effect(obtundant) on the pulp in deepcavities, reducing pain.
Optical Properties :The set cementis opaque.
-
7/29/2019 Lec. 3 Mat. Cements
34/40
Manipulation
The bottles are shaken gently.Measured quantity of powder and
liquid is dispensed onto a cool glassslab. The bulk of the powder isincorporated into the liquid andspatulated thoroughly in a circular
motion with a stiff bladed stainlesssteel spatula. Smaller increments arethen added until the mix is complete.
-
7/29/2019 Lec. 3 Mat. Cements
35/40
Setting Time 4-10 minutes.
ZOE cements set quickly in the mouth
due to moisture and heat.
-
7/29/2019 Lec. 3 Mat. Cements
36/40
Modified Zinc Oxide-EugenolCements
EBA-Alumina modified cements
Polymer reinforced.
-
7/29/2019 Lec. 3 Mat. Cements
37/40
EBA-Alumina Modified Cements
Composition
Powder : Zinc oxide-70% & Alumina-
30%.Liquid :EBA 62.5% (orthoethoxy
benzoic acid) Eugenol-37.5%.
Properties :Its properties are betterthan that of unmodified ZOE.
Setting Time 9.5 minutes
-
7/29/2019 Lec. 3 Mat. Cements
38/40
Polymer Reinforced Zinc Oxide-EugenolCement
Uses
1. Luting agent
As base
As temporary filling material and
As cavity liner.
-
7/29/2019 Lec. 3 Mat. Cements
39/40
Composition Powder
Zinc oxide 70%
Finely divided natural or synthetic resins. Liquid
Eugenol
Acetic acid acceleratorThymol antimicrobial
-
7/29/2019 Lec. 3 Mat. Cements
40/40
Properties These cements have improved mechanical
properties and the Pulp response Similar tounmodified ZOE-moderate
Manipulation The proper powder/liquid is dispensed on a
dry glass slab. The powder is mixed into theliquid in small portions with vigorousspatulation.
Working timeThese cements have a longworking time.