Learning how to Weld.
description
Transcript of Learning how to Weld.
![Page 1: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/1.jpg)
Learning how to Weld.
Sit down and be quiet.
Remember there is no such thing as a perfect weld.
![Page 2: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/2.jpg)
Welding defined
Arc welding is one of several fusion processes for joining metals. By applying intense heat, metal at the joint between two parts is melted and caused to intermix – directly, or more commonly, with an intermediate molten filler metal. Upon cooling and solidification, a metallurgical bond is created.
The arc produces a temperature of about 6500 degrees F at the tip of the rod.
![Page 3: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/3.jpg)
Safety
Must wear welding helmet Must wear long sleeve shirt Must wear blue jeans or pants Must wear close toed shoes Must wear welding gloves (both hands) Safety glasses worn (under helmet)
![Page 4: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/4.jpg)
Different types of welding
OFW Oxyfuel Gas Welding SMAW Shielded Metal Arc Welding SAW Submerged Arc Welding GMAW Gas Metal Arc Welding (MIG) FCAW Flux Cored (Wire) Arc Welding GTAW Gas Tungsten Arc Welding (TIG) PAW Plasma Arc Welding
![Page 5: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/5.jpg)
Basic Knowledge
Type of weld joints: T, Butt, Lap, Corner, and Edge Type of welds: Fillet weld or groove weld Fillet weld – A right triangle cross section of filler
metal deposit joining two pieces of base material at or nearly perpendicular to each other.
Groove weld – requires some base material prep work of at least a single bevel face.
![Page 6: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/6.jpg)
Basic Knowledge
Welding Positions: The main key of knowing welding positions is ask what is the weld face in? Below is a list of numeric then alpha meanings:
– 1 stands for flat position– 2 stands for horizontal position– 3 stands for vertical position– 4 stands for overhead position
– F stands for fillet weld– G stands for groove weld
So if you are welding a vertical fillet weld, what numeric alpha position are we welding?
![Page 7: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/7.jpg)
Basic Knowledge
Answer is 3F This knowledge is found on blueprints in or near the
welding symbols.
More symbol reading will be covered in your next year classes.
![Page 8: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/8.jpg)
WeldingPositions
Flat welds are either 1F or 1G
Horizontal welds are either 2F or 2G
Vertical welds are either 3F or 3G
Overhead welds are either 4F or 4G
![Page 9: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/9.jpg)
Welding Rods
What does those numbers mean? The “E” stands for arc welding electrode First two represent the tensile strength
– E60 is 60,000 lbs strength– E110 is 110,000 lbs strength
![Page 10: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/10.jpg)
Welding Rods
Next to last digit indicates position the electrode can be used in.
3 different positions exist:– 1 – is for use in all positions– 2 – is for flat and horizontal only– 3 – is for flat welding only
Last digit represents AC, DC+ (reverse polarity) or DC- (straight polarity)
![Page 11: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/11.jpg)
Welding Rods
Here is a list of the numbers:– 0 DC+ electrode
(reverse polarity)– 1 AC or DC- (straight
polarity)– 2 AC or DC-– 3 AC, DC-, or DC+
– 4 AC, DC-, or DC+ – 5 DC+– 6 AC or DC+– 8 AC, DC-, or DC+
![Page 12: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/12.jpg)
Welding Rods
E6010 rod is used for all position in DC reverse and produces a deep penetrating weld, does not leave a superior weld appearance.
E6011 rod is very similar to 6010, but can be used with AC or DC (both).
E6013 rod can be used in AC & DC and produces a medium penetrating weld with superior weld appearance.
E7018 rod is known as low hydrogen electrode in AC or DC (both). This electrode must be kept really dry, if allowed to get wet, you must dry it before using.
![Page 13: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/13.jpg)
What is polarity?
DC Straight – electrode is negative and the weld will have a faster melt off and deposit rate. The weld will have medium penetration.
DC Reverse – electrode is positive and the weld penetration will be deep.
![Page 14: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/14.jpg)
Welding Angle based on Positions
The next slide will show you the different angle to hold the electrodes based on the welding position you are welding in.
![Page 15: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/15.jpg)
![Page 16: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/16.jpg)
How to setup
Attach your ground clamp to the table or the work piece.
Put the rod in the stinger Get gloves on, welding helmet down Move your rod down to the metal to strike
![Page 17: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/17.jpg)
How to strike the Arc
First, you will drag to start
Do not stab Gently touch and drag Next, you will move
back to start a puddle Puddle up before
starting to move on
![Page 18: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/18.jpg)
Actually Welding
Now that you have your puddle going…
Watch rod/metal relationship
Watch speed of movement
Most important watch your puddle
![Page 19: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/19.jpg)
Welding Pictures
![Page 20: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/20.jpg)
Running your puddle
Here is a great shot of a running puddle
Notice how you can see the path of welding
![Page 21: Learning how to Weld.](https://reader035.fdocuments.net/reader035/viewer/2022062221/568146ea550346895db42392/html5/thumbnails/21.jpg)
Review
Wear proper safety equipment
Lightly drag, do not stab
Watch puddle, rod/metal relationship