KBM 3 18 - kelberg.com · KBM/3/32 Ver.1 | Issued 11/19 Tel: 01869 343 511 Page: 2 Email:...
Transcript of KBM 3 18 - kelberg.com · KBM/3/32 Ver.1 | Issued 11/19 Tel: 01869 343 511 Page: 2 Email:...
Drum SpecificationsModel KBM/3/32
Ver.1 | Issued 11/19
Tel: 01869 343 511Email: [email protected]: 3 Whilst every effort has been made to ensure the accuracy of the information in this spec sheet, some errors may occur. It is important that you do not solely rely upon this information, but that you
check with your dealer any items you feel will affect your decision to purchase this vehicle. No liability for loss or damage resulting from errors or misleading information will be accepted by Kel-Berg Trailers & Trucks Ltd. This specification is for guidance only and does not constitute an offer of sale or guarantee of the specification of this vehicle. All specifications are subject to change without notice and/or verification. E&OE.
Mixer Drive-Line:
Rear Control Station:
PTO
Gearbox
Pump
Cooler
Motor
Oils
Engine
Slumping
Water
Other
GKN shaft from auxiliary drive PCE, 687.15 Series, 670mm W/L, 100 mm DIN Flanges, 6 X M8 Bolt Holes
PMP B6.5 1202.4 hydraulic pump drives the water pump via a sheer coupling.
PMH P90 Pump. Maximum Pressure 450 bar. Axial pistons and variable flow pump. 89.5 cm³ / 89.5cc capacity
ASA oil cooler with temperature control via 59° thermostat, 20 L oil reservoir and filter
PMH M90 Hydraulic Pump. 89.5 cm³ / 89.5cc displacement. Fixed Flow
Hydraulic: SAE7580Gearbox: SAE85W90
3” hydraulic pressure gauge mounted in rear control panel to provide indication of slump.
1” BSP stainless steel control valve and batching meter.
Any other additional options
The mixer is controlled via cable located both at the rear & incab. Engine revs controlled by push buttons.
Photos:
Drum SpecificationsModel KBM/3/32
Ver.1 | Issued 11/19
Tel: 01869 343 511Email: [email protected]: 4 Whilst every effort has been made to ensure the accuracy of the information in this spec sheet, some errors may occur. It is important that you do not solely rely upon this information, but that you
check with your dealer any items you feel will affect your decision to purchase this vehicle. No liability for loss or damage resulting from errors or misleading information will be accepted by Kel-Berg Trailers & Trucks Ltd. This specification is for guidance only and does not constitute an offer of sale or guarantee of the specification of this vehicle. All specifications are subject to change without notice and/or verification. E&OE.
Photos:Water SystemTank Size
Pump
Meter
Valves
Tank Fill
Wash Off
Drain Point
400 Litre maximum capacity aluminium tank with external sight glass.
Direct drive centrifugal pump driven by mixer gearbox PTO featuring sacrificial sheer coupling to protect mixer gearbox in the event of frost.
1-1/4” Maddalena BSP, brass flow-meter with analogue display and reset facility. Each end connected with quick release for ease of change.
1-1/2” BSP stainless steel ball valves, robust with improved stem seal and rugged steel handle
One nearside, one off side front with compressed air style claw coupling.
3/4” hoses with brass nosed to rear at ground level and at ladder platform
1/4” BSP stainless steel ball valve at front, middle and rear. Rear and middle to drain whole system. Front is low and drains pump.
Drum SpecificationsModel KBM/3/32
Ver.1 | Issued 11/19
Tel: 01869 343 511Email: [email protected]: 5 Whilst every effort has been made to ensure the accuracy of the information in this spec sheet, some errors may occur. It is important that you do not solely rely upon this information, but that you
check with your dealer any items you feel will affect your decision to purchase this vehicle. No liability for loss or damage resulting from errors or misleading information will be accepted by Kel-Berg Trailers & Trucks Ltd. This specification is for guidance only and does not constitute an offer of sale or guarantee of the specification of this vehicle. All specifications are subject to change without notice and/or verification. E&OE.
Body FittingsChutes & HoppersCharge Ladder
Platform
Mudwings
Sideguards
Warning Signs
Discharge
Pan-Chute
Spares
Chute Actuation
Single steel piece high flow with wear plate Fixed ladder gives access to wide platform and features anti-slip rungs. Pull out to lower ladder.
Large anti-slip platform with step to right and handrail with auto close anti-fall back barrier.
Three piece thermo-plastic / galvanised steel combination with gloss finish for easy cleaning.
Bolt on galvanised channel with hinged legs and anodised aluminium side rails. Type Approved
Warning badges for “cement burns”, “authorised operator only”, “rotating parts” etc
High capacity discharge hopper with wear liner
3 mm (130cm long) pan chute with wear liner
2 spare plastic chutes which are mounted on top of mudwings each side.
Mechanical screw jack ram for rise and fall of pan-chute with manual rotation with clamping lock.
Drum SpecificationsModel KBM/3/32
Ver.1 | Issued 11/19
Tel: 01869 343 511Email: [email protected]: 6 Whilst every effort has been made to ensure the accuracy of the information in this spec sheet, some errors may occur. It is important that you do not solely rely upon this information, but that you
check with your dealer any items you feel will affect your decision to purchase this vehicle. No liability for loss or damage resulting from errors or misleading information will be accepted by Kel-Berg Trailers & Trucks Ltd. This specification is for guidance only and does not constitute an offer of sale or guarantee of the specification of this vehicle. All specifications are subject to change without notice and/or verification. E&OE.
NOTES:- All materials to be confirmed.- Drawing for costing / prototype only-- NOT FOR MANUFACTURE --
MASS:
LATEST ISSUE:
SIGN. :
DRAWING NUMBER :
REV
DATE
THIS DRAWING MUST NOT BE COPIED WITHOUT KELBERG'S PERMISSION
SURFACE :SCALE :
LATEST ISSUE DATE:NJS
28/05/20191:35
CRPC 2250 01 002
N/A
A
MATERIAL :
Tolerance:Not tolerance target set byDS / ISO 2768-1 "m"+-1,5mm --> 3000 - 7000mm