KA AC SD PALM TREE Kala Palm Tree Stand „Sales Promotion Stand“ KA AC SD 12UKE DISPL Kala 12 Uke Sales Promotion Stand

Kala Palm Tree Stand Kala Sales PromotionStand

Display for retail space,designed as a palm tree.For 9 or more instruments

Display for sale room, � oor stand for 12 Instruments.

Doe

s no

t com

e w

ith u

kule

les

ASSEMBLY INSTRUCTIONS

STEP 1: ASSEMBLE BASE Parts needed:1 – open star (#1 through #12)6 – feetProcess:• Slide feet into star to form base

STEP 4: TOP TRUNK AND FINAL DETAILSParts needed:1 – open star (#25 through # 36)6 – top truck sections6 – fronds9 – ukulele holders20 - screwsProcess:• Insert legs into corresponding

number slots. Add open star to top insuring tab and slot numbers match, and that the numbers are facing up.

• Install star screws before adding fronds

• Add fronds, being certain to match the numbers.

• Install ukulele holders into corre-sponding number slots, and add screws.

• When installing uke holders note that one side is pre-drilled and that should be where you install the screw. Tie ropes into holes in 3 of the fronds so that ukes can be hung.

STEP 2: ADD BOTTOM TRUNKParts needed:1 – closed star (#13 through #18)6 – lower trunk sections (#7 through

#12)12 - screwsProcess: • Insert lower trunk sections into corre-

sponding slot• Add closed star with numbers facing

up• Insert and tighten 12 screws into

countersunk screw areas

Parts Parts

6 Lowersections#7 - #12

18 Trunk pieces (numbers on ends)

6 Middlesections#13 - #18

6 Topsections#19 - #24

6 Fronds(numbers on

ends)

9 Numbered ukuleleholders

4 Stars (numbers on points)

2 - open ends2 - closed ends

6 Feet Ropes,Screws

Kala Palm Tree Stand

STEP 1: Assemble sides and bottom braces: • Install bottom braces (Large

14 ½”, and Thin 14”) into one of the sides.

• Add second side, and secure both braces into both sides

STEP 2: Add medium and small braces, and sign:• Install medium brace into middle section, and secure. • Install small brace into next

section up, and secure

Photo 4, complet “tower” without sign

STEP 3: Secure sign at top

Kala Sales Promotion Stand

STEP 3: ADD MIDDLE TRUNKParts needed:1 – closed star (#19 through #24)6 – middle trunk sections (#13 through

#18)6 - screwsProcess: • Insert legs into corresponding num-

ber slots• Add closed star with numbers facing

up• Insert and tighten screws around

perimeter

TOOLS NEEDED:Small Phillips screwdriver (for set screws)Small ladder or step stoolTWO VERY IMPORTANT NOTES:1) Many of the parts look alike.It is extremely important to connect the parts with their corre-sponding numbers as designed.2) Tree should be assembled in the location you plan to display it in.Height: 230 cm

TOOLS NEEDED:Small Phillips screwdriver (for set screws)Small ladder or step stoolTWO VERY IMPORTANT NOTES:1) Many of the parts look alike.It is extremely important to connect the parts with their corre-sponding numbers as designed.2) Tree should be assembled in the location you plan to display it in.Height: 230 cm

TOOLS NEEDED:Rubber Mallet (for lightly tapping to secure braces)TWO VERY IMPORTANT NOTES:Unit is simple to assemble, but must be built in this exact order for all of the parts to � t correctly.Height: 183 cm

TOOLS NEEDED:Rubber Mallet (for lightly tapping to secure braces)TWO VERY IMPORTANT NOTES:Unit is simple to assemble, but must be built in this exact order for all of the parts to � t correctly.Height: 183 cm

• 1 Kala Sign• 1 Left side• 1 Right side• 1 Thin brace approximately 14”• 1 Small brace approximately 12 1/4”• 1 Medium brace approximately 13 3/8”• 1 Large brace approximately 14 1/2”

Photo 1

Photo 4 Photo 5

Photo 2 Photo 3