JB7-4U...INTRODUCTION ABOUT YOUR SYSTEM 1-1 1.1 Introduction MESOS M4240H is a 4U storage server...

Version: 1.0.0

MESOS Series

M4240HHigh-Density 4U Disk Expansion Unit

User’s Guide

TABLE OF CONTENTS

About the SystemIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3

A Tour of the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4System Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5Storage Drive Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6Front Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6System Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7Power Supply Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

LED Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10Storage Drive Tray LEDs Definition. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10Front Control Panel LED Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10PSM LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11Mini-SAS Port LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12SAS Interface Module Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12Management Port LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13

Installing HardwareSafety Measures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Hot-plug Storage Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Removing a Storage Drive Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Installing a Storage Drive Tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Removing Storage Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Installing Storage Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Install / Replace Storage Drives Configuration. . . . . . . . . . . . . . . . . . . 2-3Recommended Storage Drive Configurations . . . . . . . . . . . . . . . . . . . 2-4

Power Supply Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7

Removing the Power Supply Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7Installing the Power Supply Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9

I

SAS Interface Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11

Removing the SAS Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11Installing the SAS Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12

Configure your systemUsing CLI commands to configure your system. . . . . . . . . . . . . . . . . . . . . . . . . 3-1

CLI Commands List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1exit CLI service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2set DHCP client status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3set static ip, subnet mask, and gateway . . . . . . . . . . . . . . . . . . . . . . . . . 3-3control zoning configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4display and erase system log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5reboot expander . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5reset FRU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6disable FRU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7enable FRU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8display system status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8display and set system SAS address . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10display and set system FAN speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11display and set system date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12display ports information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12display disks information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13display who is the console management. . . . . . . . . . . . . . . . . . . . . . . 3-14display system version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14close TCP/IP session. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15display all CLI command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15

System Firmware Update . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18

Configuring your serial terminal emulation program. . . . . . . . . . . . . . 3-18Configuring your terminal emulation program . . . . . . . . . . . . . . . . . . . 3-20Input the password to enter command line interface (CLI) mode . . 3-22Check your firmware version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23Update your system firmware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24

II

REVISION HISTORY REGULATORY AND COMPLIANCE INFORMATION

Revision HistoryRefer to the table below for the updates made to this technical guide.

CopyrightCopyright © 2014 Quanta Computer Inc. This publication, including all photographs, illus-trations and software, is protected under international copyright laws, with all rights reserved. Neither this guide, nor any of the material contained herein, may be reproduced without the express written consent of the manufacturer. All trademarks and logos are copyrights of their respective owners.

Version 1.0.0 / July 21, 2014

DisclaimerThe information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifi-cally disclaims any implied warranties of merchantability or fitness for any particular pur-pose. Furthermore, the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufac-turer to notify any person of such revision or changes.

For the latest information and updates please see www.QuantaQCT.com

All the illustrations in this guide are for reference only and are subject to change without prior notice.

DATE CHAPTER UPDATES

III

REGULATORY AND COMPLIANCE INFORMATION REVISION HISTORY

About the Book

This guide is written for users who want to know the system featuers.

For the latest version of this guide, see www.QuantaQCT.com.

Intended Application Uses

This product was evaluated as Information Technology Equipment (ITE), which may be installed in offices, schools, computer rooms, and similar commercial type locations. The suitability of this product for other product categories and environments (such as medical, industrial, residential, alarm systems, and test equipment), other than an ITE application, may require further evaluation.

IV

CONVENTIONS

V

ConventionsSeveral different typographic conventions are used throughout this manual. Refer to the following examples for common usage.

Bold type face denotes menu items, buttons and application names.

Italic type face denotes references to other sections, and the names of the folders, menus, programs, and files.

<Enter> type face denotes keyboard keys.

WARNING!Warning information appears before the text it references and should not be ignored as the content may prevent damage to the device.

CAUTION!CAUTIONS APPEAR BEFORE THE TEXT IT REFERENCES, SIMILAR TO NOTES AND WARNINGS. CAUTIONS, HOWEVER, APPEAR IN CAPITAL LETTERS AND CONTAIN VITAL HEALTH AND SAFETY INFORMATION.

Note:Highlights general or useful information and tips.

!

!

Structure of this guide Chapter 1: About the System

“This section introduces the system, its different configuration(s) and the main features.”

Chapter 2: Installing Hardware

“This section provides guidance information to properly service components in the system.”

Chapter 3: Configure your system

“This section provides information regarding the system firmware update, and command line interface (CLI) commands found in the system.”

VI

About the SystemChapter 1

This section introduces the system, its different configuration(s) and the main features.

INTRODUCTION ABOUT YOUR SYSTEM

1.1 IntroductionMESOS M4240H is a 4U storage server specially tailored to meet the scale-out storage needs of diverse datacenters. It features large storage capacity of up to 24 x 6G SAS or 6G/3G SATA hot-plug 3.5” storage drive devices in 4U size, 6 x 6Gb/s mini-SAS ports, 2 x RJ11 console port, 2 x RJ45 management port (2 controller modules), 2 x 760W redundant PSUs.

The MESOS M4240H is a great choice for applications such as highly scalable and high-throughput object storage and distributed file system in cloud datacenters.

Provide Extremely Large Storage in 4U Space

Big Data is getting particularly much attention today because of the growth predictions for data. MESOS M4240H is a standard 4U rackmount system. It amazingly supports up to 24 x 2.5" or 3.5" hot-plug SAS/SATA HDD/SSD bays. It provides unprecedented storage combinations and capacity in a 4U chassis for diverse datacenters. Moreover, the system eliminates unnecessary features and positioned itself as a pure storage server, powered by Quanta MESOS solution.

Bring You the Most Scale Up with Daisy-Chain Design

MESOS M4240H not only lowers the cost, but also highly increases the scale up to 72 stor-age drives (total 3 sets of M4240H systems) because of its daisy-chain design. The excep-tional design makes all components work smoothly together. Plus two redundant 760W power supply modules, the MESOS M4240H can be ranked as one of the most efficient server ever.

Specifications

Table 1.1: System Specifications

SPECIFICATIONS DESCRIPTION

Form factor 4U rack mount

Dimensions (W x H x D)17.52 x 6.88 x 21.93 inches 445 x 174.75 x 557.02 mm

Weight 64.53 lb. (29.33kg)

Controller Module 2x hot-plug SAS Interface Modules (SIM)

External I/O Ports 3x 6 Gb/s mini-SAS ports per SIM

Storage24 x 3.5" or 2.5" 6G SAS and 6G/3G SATA hot-plug HDDs with dual-port access. (SATA drive requires optional Active-Active MUX)

Management Port 1x RJ45 management port

Expansion Support Scalable up to (72) storage drives in cascading (3) M4240H

Power Supply (2) 760W redundant power supplies, input requirements 88 - 264V AC

Fan Total 2+2 redundant in the system, 2 fans in each power supply module

1-1

ABOUT YOUR SYSTEM INTRODUCTION

LED Indicators

Front Control Panel: Power LEDSystem ID / Status LED

Storage Drive Bay:Identify LEDFail / OK LED

PSUAC Power LEDDC Power LEDPower Supply Status LEDCooling Fans Status LED

SAS Interface Module (SIM)Power LEDLocate LEDSAS port status LEDsRJ45 port LEDs

Operating Environment

Operating Temperature: 0°C to 40°C (32°F to 104°F)Humidity: 50% to 93% relative humidityAltitude: 40°C / 3200 MeterShock : [email protected], half-sine shockOperational Vibration: 0.26Grms random vibration 5~350Hz

Table 1.1: System Specifications (Continued)

SPECIFICATIONS DESCRIPTION

1-2

PACKAGE CONTENTS ABOUT YOUR SYSTEM

1-3

1.2 Package Contents (1) M4240H system

(96) 6/4 storage drive screws

(2) power cords (optional)

(1) Console cable

(1) utility CD

(1) rail kit

Note:Note: For exact shipping contents, contact your Quanta sales representative.

ABOUT THE SYSTEM A TOUR OF THE SYSTEM

1.3 A Tour of the System

System Overview

Figure 1-1. System Overview

Figure 1-2. System Overview

1-4

SYSTEM OVERVIEW ABOUT THE SYSTEM

System Front View

Figure 1-3. System Front View

Table 1.2: Front View

NO. NAME DESCRIPTION

1 Storage Drive Bay

Support 24 x 2.5” / 3.5”; 6G SAS / 6G (3G) SATA; HDD / SSD trays. Please follow the sequence below from left to right, top to bottom for device numbers:1 2 3 45 6 7 89 10 11 1213 14 15 1617 18 19 2021 22 23 24

2 Control Panel

Control Panel includes the following: System Identify LED System Status LED System Identify Button

1 2

1-5

ABOUT THE SYSTEM SYSTEM OVERVIEW

Storage Drive Tray

Figure 1-4. 3.5” Storage Drive Tray

Front Control Panel

Figure 1-5. Front Control Panel View

Table 1.3: Storage Drive Tray

NO. ITEM DESCRIPTION

1 Identify LED Display to identify the storage drive for removing

2 Fault / OK LED Display to indicate the status of the storage drive

3 Release button Press to release the handle of storage drive tray

4 Device Number Dedicated for the Storage drive number.

5Handle of storage drive tray

Hold the handle and pull the storage drive tray out with care.

1 2 3 4 5

1

2

3

1-6


System Rear View

Figure 1-6. System Rear View

Table 1.4: Front Control Panel View

NO. ICON NAME DESCRIPTION

1 System Identify (ID) LED Lights when Identify button is pressed.

2 System Fault/OK LED Lights for system status

3 ID Button Push button to light up / off the System Identify (ID) LED.

Table 1.5: Rear Panel View


1 PSMRedundant Power Supply Module (PSM) (optional)Left: PSM1Right: PSM2

2 SIMRedundant SAS Interface Module (SIM) (optional)Left: SIM1Right: SIM2

1

2

1-7

ABOUT THE SYSTEM SYSTEM OVERVIEW

Power Supply Module

Figure 1-7. Power Supply Module Rear View

Table 1.6: PSM rear view


1 Fan Cooling the Power Supply Module (PSM).

2 PSM LEDs Lights for PSM status.

3 Switch Turns the PSM on / off.

4 Socket Connects to power cord.

5 LeverLossen thumb screw, pull out and holding the lever with hands for removing the PSM from chassis bay.

1 2 3

5 4 5

1

1-8


SAS Interface Module View

Figure 1-8. SAS Interface Module View

Table 1.7: SIM View


1SAS-IN connector 1 with status LEDs

Mini-SAS connector. Connects to server system.

2SAS-IN connector 2 with status LEDs


3 LeverLossen thumb screw, pull out and holding the lever with hands when removing the SIM from chassis bay.

4SAS-OUT connector with status LEDs


5 Management port RJ45 connector. Connects to network for remote management.

6 Service port RJ11 connetor. Connects to local system for maintenance or debuging.

7 Status LEDs Lights for SIM status

1 2 3 4 3 75 6

1-9

ABOUT THE SYSTEM LED DEFINITIONS

LED Definitions

Storage Drive Tray LEDs Definition

Figure 1-9. Storage Drive Tray LEDs

Front Control Panel LED Definition

Figure 1-10. Fornt Control Panel LEDs

Table 1.8: Storage Drive Tray LEDs View


1 Identify LEDGreen On, HDD is ready for removingOFF, Normal operation

2 Fault / OK LED

Amber On, HDD FaultBlue On, Ready for accessBlue Blinking, Disks spin up or accessing disksOFF, Normal operation

Table 1.9: Front Control Panel View


1 System Identify (ID) LEDWhite blinking, selected unit IDOFF, no ID requested

1 2

1

2

1-10

LED DEFINITIONS ABOUT THE SYSTEM

PSM LEDs

Figure 1-11. PSM LEDs

2 System Fault/OK LEDAmber On, System FaultGreen On, System is powered onOFF, system OK.

Table 1.10: PSM LEDs


1 AC power LEDGreen On, AC power readyOFF, no AC power

2 Fan status LEDAmber On, Fan fault.OFF, no fault.

3 PSM fault LEDAmber On, PSM fault.OFF, no fault.

4 DC power LEDGreen, DC power readyOFF, no DC power

Table 1.9: Front Control Panel View (Continued)

1

2

4

3

1-11

ABOUT THE SYSTEM LED DEFINITIONS

Mini-SAS Port LED

There are two indicators in each mini-SAS port.

Figure 1-12. mini-SAS port

SAS Interface Module Status LED

There are two indicators in the SAS Interface Module.

Figure 1-13. SAS Interface Module Status LED


1mini-SAS port LED (Green) Green On + Amber Off, mini-SAS ready

Green Off + Amber On, no mini-SASGreen Blinking + Amber On, mini-SAS fault.Green Blinking + Amber Off, no fault.2

mini-SAS fault LED (Amber)


1 System Fault/OK LEDAmber On, System FaultGreen On, System is powered onOFF, system OK.

2 System Identify (ID) LEDWhite blinking, selected unit IDOFF, no ID requested

1-12

LED DEFINITIONS ABOUT THE SYSTEM

Management Port LED

The SIM has one 1G port to support management for remote connection and service.

Each RJ45 connector has two built-in LEDs. See the following illustration and table for details.

Figure 1-14. RJ45 LAN Connector

Table 1.11: RJ45 LED Description

STATUS LINK / ACTIVITY LED SPEED LED

Unplug Off Off

1G Link with Active Green blinking Amber On

100M Link with Active Green blinking Green On

10M Link with Active Green blinking Off

Link/Activity Speed

PIN 1Location

1-13

Installing HardwareChapter 2

This section provides guidance information to properly service components in the sys-tem.

SAFETY MEASURES INSTALLING HARDWARE

2-1

2.1 Safety Measures

WARNING!Always ask for assistance to move or lift the system.

WARNING!Only perform troubleshooting as authorized by the product documentation, or as directed by a service and support team. Repairs not authorized by warranty may void the warranty and damage the system.

WARNING!Always make sure to disconnect the system from the AC electrical source. Powering down the system DOES NOT ensure there is no electrical activity in the system.

WARNING!Server components and circuit boards are easily damaged by discharges of static electricity. Working on servers that are connected to a power supply can be extremely dangerous. Follow the guidelines below to avoid personal injury or damage to the server.

WARNING!Always disconnect the server from the power outlet whenever you are working inside the server case.

WARNING!Wear a grounded wrist strap. If none are available, discharge any personal static electricity by touching the bare metal chassis of the server case, or the bare metal body of any other grounded device.

WARNING!Humid environments tend to have less static electricity than dry environments. A grounding strap is warranted whenever danger of static electricity exists.

WARNING!Do not touch the components on the unless it is necessary to do so. Do not flex or stress circuit boards.

WARNING!Leave all replacement components inside their static-proof packaging until you are ready to use them.

!

!

!

!

!

!

!

!

!

INSTALLING HARDWARE HOT-PLUG STORAGE DRIVES

2.2 Hot-plug Storage Drives

The system supports up to twenty-four (24) hot-plug storage drives.

Figure 2-1. Storage Drive Bay Described

Removing a Storage Drive Tray1. Press the storage drive tray release button (blue) to unlock the tray.

2. Pull the storage drive tray handle open.

3. Pull the storage drive tray assembly out of the system.

Installing a Storage Drive Tray1. Insert the storage drive tray assembly into the chassis.

2. Push the storage drive tray assembly handle to close.

Removing Storage Drives

CAUTION!ENSURE ALL POWER IS DISCONNECTED FROM THE SYSTEM BEFORE PROCEEDING.

WARNING!Repairs should be performed by a certified service technician. Damage to the system or com-ponents due to unauthorized servicing is not covered by the warranty agreement.

CAUTION!STORAGE DRIVE MODULES ARE HOT TO THE TOUCH WHEN REMOVED FROM THE SYSTEM. PROTECTIVE GEAR IS RECOMMENDED TO PREVENT PERSONAL INJURY OR DAMAGE TO THE HARDWARE.

!

!

!

2-2

INSTALLING A STORAGE DRIVE TRAY INSTALLING HARDWARE

1. Remove the storage drive tray assembly from the storage drive bay.

2. Remove the four 6/4 securing screws from the storage drive and tray.

3. Lift the storage drive to remove.

Installing Storage Drives

Note:If using SATA drive, please make sure having Interposer card installed on the back of storage drive tray

1. With the connectors facing the open end of the storage drive tray, align the storage drive over the storage drive tray.

2. Install the tray and secure with the four 6/4 screws.

3. Replace the storage drive tray assembly in the drive bay.

Install / Replace Storage Drives Configuration

SAS and SATA Storage Drive is not recommended mixing in the same system. It’s sug-gested to use the following figures below to plan where you will install the storage drives.

These figures represent fully-loaded system with storage drives.

Figure 2-2. Storage Drive Bay Described

However, the same guidelines apply even if you are filling some of the storage drive slots with blank trays in the mixing storage drive setting.

SATA / SAS #1

SATA / SAS #5

SATA / SAS #9

SATA / SAS #13

SATA / SAS #17

SATA / SAS #21

SATA / SAS #2

SATA / SAS #6

SATA / SAS #10

SATA / SAS #14

SATA / SAS #18

SATA / SAS #22

SATA / SAS #3

SATA / SAS #7

SATA / SAS #11

SATA / SAS #15

SATA / SAS #19

SATA / SAS #23

SATA / SAS #4

SATA / SAS #8

SATA / SAS #12

SATA / SAS #16

SATA / SAS #20

SATA / SAS #24

2-3

INSTALLING HARDWARE INSTALLING A STORAGE DRIVE TRAY

Recommended Storage Drive Configurations

Figure 2-3. Storage Drive Bay Described - All SATA

Figure 2-4. Storage Drive Bay Described - 3 SATA + 1 SAS


SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SAS

SAS

SAS

SAS

SAS

SAS

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

2-4

INSTALLING A STORAGE DRIVE TRAY INSTALLING HARDWARE


Figure 2-7. Storage Drive Bay Described - All SAS

Figure 2-8. Storage Drive Bay Described - 3 SAS + 1 SATA

SATA

SATA

SATA

SATA

SATA

SATA

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SATA

SATA

SATA

SATA

SATA

SATA

2-5

INSTALLING HARDWARE INSTALLING A STORAGE DRIVE TRAY



Note:It’s not suggested to install the SATA and SAS storage drive in the same column for performance. It’s also not suggested to install a column of SATA (SAS) storage drives between two columns of SAS (SATA) storage drives for performance.

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SAS

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SAS

SAS

SAS

SAS

SAS

SAS

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

SATA

2-6

POWER SUPPLY MODULE INSTALLING HARDWARE

2.3 Power Supply ModuleIf your system is configured in a redundant configuration, you can replace a failed or fail-ing power supply without powering down the server. Use the LEDs on the power supply to determine the status of the target PSM.

Each power supply module has the LED above the input connector, see PSM LEDs on page 1-11.

Removing the Power Supply Module

1. Rotate the cable clip around the cable connector and open.

Figure 2-11. Releasing the cable clip

2. Guide the cable tie through the cable clip as shown.

CAUTION!ENSURE ALL POWER IS DISCONNECTED FROM THE SYSTEM BEFORE PROCEEDING.ENSURE THE POWER SUPPLY ON/OFF SWITCH IS IN THE “O” POSITION.!

2

1

2-7

INSTALLING HARDWARE REMOVING THE POWER SUPPLY MODULE

3. Disconnect the power cord from the power supply.

Figure 2-12. Disconnecting the Power Cord

4. Remove the cable tie from the power supply.

5. Lossen both ejection arm captive screws and swing the ejection arms out until fully open.

6. Pull the power supply from the chassis and set it on a clean workspace.

Figure 2-13. Removing a PSM

4

3

2-8

INSTALLING THE POWER SUPPLY MODULE INSTALLING HARDWARE

Installing the Power Supply Module

1. Locate the target power bay.

2. Remove the new power supply from the protective packaging and place it on a clean ESD protected work surface.

3. Align the AC inlet connector on the middle and slide the new power supply module into the power supply bay until it latches in place and flush with the chassis.

4. Fasten the ejection arm captive screws and secure the ejection arms.

Figure 2-14. Installing a PSM

CAUTION!ENSURE ALL POWER IS DISCONNECTED FROM THE SYSTEM BEFORE PROCEEDING.!

2-9

INSTALLING HARDWARE INSTALLING THE POWER SUPPLY MODULE

5. Insert the cable tie to the power supply.

Figure 2-15. Inserting the Power Cord

6. Insert the power cord into the AC receptacle on the power supply

7. Guide the cable tie through the cable clip as shown.

Figure 2-16. Securing the cable clip

8. Rotate the cable clip around the cable connector and close.

9. Switch on the power supply - ensure the power supply on/off switch is in the “l” position.

10. Use the LED on the power supply to confirm that the power supply is functioning.

5

6

7

8

2-10

SAS INTERFACE MODULE INSTALLING HARDWARE

2.4 SAS Interface ModuleIf your system is configured in a redundant configuration, you can replace a failed or fail-ing SAS Interface Module (SIM) without powering down the system. Use the LEDs on the SIM to determine the status of the target SIM.

Each SAS Interface Module has the LEDs on it, see SAS Interface Module Status LED on page 1-12.

Removing the SAS Interface Module

1. Locate the target SAS Interface Module for removing.

2. Disconnecting all cabling from SAS Interface Module.

3. Lossen the ejection arm captive screws and swing the ejection arms out until fully open.

Note:To avoid damaging the SAS Interface Module, support the module with the second hand when pulling out of the chassis.

4. Holding the two ejection arms and pull the SAS Interface Module out from the chas-sis.

CAUTION!TO AVOID SYSTEM OVERHEATING, ALL PROCEDURES ON THIS SECTION SHOULD BE PERFORMED WITHIN 10 MIN-UTES.!

2-11

INSTALLING HARDWARE INSTALLING THE SAS INTERFACE MODULE

5. Pull the SAS Interface Module from the chassis and set it on a clean workspace.

Figure 2-17. Removing a SAS Interface Module

Installing the SAS Interface Module

1. Locate the target SAS Interface Module bay for installing.

2. Remove the new SAS Interface Module from the protective packaging and place it on a clean ESD protected work surface.

3. Align the SAS Interface Module connector on the bottom and slide the new SAS Interface Module into the SAS Interface Module bay until ejection arms latch in place and the SAS Interface Module is flush with the chassis.

4. Push the ejection arms into the closed position until snap in place.

CAUTION!TO AVOID SERVER SYSTEM OVERHEATING, ALL PROCEDURES ON THIS SECTION SHOULD BE PERFORMED WITHIN 10 MINUTES.!

2-12

INSTALLING THE SAS INTERFACE MODULE INSTALLING HARDWARE

5. Fasten the ejection arm captive screws and secure the ejecton arms.

Figure 2-18. Installing a SAS Interface Module

6. Connecting all cabling into the SAS Interface Module.

7. Use the LED on the SAS Interface Module to confirm that the SIM is functioning.

2-13

Configure your systemChapter 3

This section provides information regarding the system firmware update, and com-mand line interface (CLI) commands found in the system.

USING CLI COMMANDS TO CONFIGURE YOUR SYSTEM CONFIGURE YOUR SYSTEM

3.1 Using CLI commands to configure your systemYour system provides a basic command line interface (CLI) commands set as an alternative for configuring the system.

In order to use the CLI, you might use the UART or Ethernet port to communicate with the system. In host side, it’s suggested to use a serial terminal emulation program like Hyper-Terminal / Putty / Tera Term or telnet/SSH application to communicate with your system. In UART port, the baud rate should be set as 115200bps. In Ethernet port, the speed can be 10M or 100M. Before entering CLI, you might need to enter the password 'jbodstorage' in the command prompt.

Note:Please connect to the system through UART port first and assign the ip / subnet mask / Gateway address using the following commands for Ethernet port connec-tion if the ip address’s information is not available.

JBOD> dhcp disable

JBOD> ip IP[a.b.c.d] SubnetMask[a.b.c.d] Gateway[a.b.c.d]

CLI Commands List

================================================================================

Description Command

================================================================================

Quit CLI Service quit

Print/Set DHCP Status dhcp <enable,disable>

Print/Set IP Address ip IP[a.b.c.d] SubnetMask[a.b.c.d] Gateway[a.b.c.d]

Zoning configuration zoning <pp,help>

Get/Clear System log syslog clr(option)

Reboot the expander reboot watchdog(optional)

Reset FRU reset <disk,ps0,ps1,peer,up,down,sda>

Disable FRU disable <disk,ps0,ps1,peer,up,down,sda>

Enable FRU enable <disk,ps0,ps1,peer,up,down,sda>

System status status

3-1

CONFIGURE YOUR SYSTEM CLI COMMANDS LIST

Set/Get SAS address sas_addr base_addr[0xXXXXXXXXXXXXXXXX]

Set/Get FAN RPM rpm level[1(3440) - 2(4765) - 3(5543)]

Show/Set Date date YEAR[00-99] MON[1-12] DATE[1-31]

HR[0-23] MIN[0-59] SEC[0-59]

Port status port

Disk status disks

Show Mastership who

Show FW version ver

Close TCP/IP session exit

CLI Help help command

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

exit CLI service

Syntax Description

None

Display Message

None

Related Commands

exit

ExamplesJBOD:>quit

Syntax

quit

3-2

CLI COMMANDS LIST CONFIGURE YOUR SYSTEM

set DHCP client status

Syntax Description

dhcp enable: Enable DHCP feature.

dhcp disable: Disable DHCP feature.

Display Message

None

Related Commands

ip

ExamplesJBOD:>dhcp enable

Please reboot SIM to let DHCP change become effective.

JBOD:>dhcp

DHCP is enabled

set static ip, subnet mask, and gateway

Syntax Description

IP: Static IP address.

SubnetMask: Network subnet mask.

Gateway: IP address of the default gateway.

Display Message

Syntax

dhcp <enable,disable>

Syntax


3-3


IP Address: Static IP address.

Subnet Mask: Network subnet mask.

Gateway: IP address of the default gateway.

Related Commands

dhcp

ExamplesJBOD:>ip 192.168.36.100 255.255.0.0 192.168.36.1JBOD:>ip

IP Address: 192.168.36.100 Subnet Mask: 255.255.0.0 Gateway: 192.168.36.1

control zoning configuration

Syntax Description

zoning: Display zoning status.

zoning help: Display the help message of zoning.

zoning pp: Toggle physical presence bit.

Display Message

None

Related Commands

None

ExamplesJBOD:>zoning help

Usage:

zoning pp - Toggle physical presence bit.

JBOD:>

Syntax

zoning <pp,help>

3-4


display and erase system log

Syntax Description

syslog: display system log.

syslog clr: Clear all system log.

Display Message

None

Related Commands

None

ExamplesJBOD:>syslog clr

[EmaEepromSyslogFlashStateSet] 0x00000000

Syslog Clear. status:0 (2012/10/29 11:52:17)

Set Syslog Cleared 00 (2012/10/29 11:52:17)

==============================================================================

System Role: SIM1/Master and Dual board

Boot cause : REGISTER_RESET

oooo oooo oooooo oooooooo

88 88 88 88 88 88

88 88ooooo 88 88 88 88

88 88 888 88 88 88 88

o 88 88 888 8o o8 88 88

888 o888ooo88 88oo88 o888oo88

Firmware Version : 1729

Build time : 2011/11/28 10:07:57

Previous Version : 1729

Prev-build time : 2011/11/28 10:07:57

Current time: 2012/10/29 11:52:17

JBOD:>

reboot expander

Syntax

syslog clr(option)

Syntax

3-5


Syntax Description

reboot: Reboot JBOD system.

reboot watchdog: Reboot watchdog

Display Message

None

Related Commands

None

ExamplesJBOD:>reboot

Performing POST for Smart Serial

Performing internal memory error counter checks as part of Internal Memory POST

Internal memory counters after self test are:

Slave0SingleBitCounter = 7ffa0, Slave0DoubleBitCounter = 0

Slave0DoubleBitAddress = 0, Slave1SinbleBitCounter = 0

Slave1DoubleBitCounter = 0, Slave1DoubleBitAddress = 7fffc

Internal memory counters after forced ECC test are:

Slave0SingleBitCounter = 1, Slave0DoubleBitCounter = 1

Slave0DoubleBitAddress = 120, Slave1SinbleBitCounter = 1

Slave1DoubleBitCounter = 1, Slave1DoubleBitAddress = 40120

forcedEccErrStatus = 1

reset FRU

Syntax Description

reset disk <id>: Reset disk.

reset ps0: Reset power supply 0.

reset ps1: Reset power supply 1.

reset peer: Reset peer expander.

reset up: Reset up stream port.

reboot watchdog(optional)

Syntax

reset <disk,ps0,ps1,peer,up,down,sda>

3-6


reset down: Reset down stream port.

reset sda: Reset system startup counter.

Display Message

None

Related Commands

enable, disable

ExamplesJBOD:>reset ps0

disable FRU

Syntax Description

disable disk <id>: Disable disk.

disable ps0: Disable power supply 0.

disable ps1: Disable power supply 1.

disable peer: Disable peer expander.

disable up: Disable up stream port.

disable down: Disable down stream port.

disable sda: Disable system startup counter.

Display Message

None

Related Commands

enable, reset

ExamplesJBOD:>disable peer

Syntax

disable <disk,ps0,ps1,peer,up,down,sda>

3-7


enable FRU

Syntax Description

enable disk <id>: Enable disk.

enable ps0: Enable power supply 0.

enable ps1: Enable power supply 1.

enable peer: Enable peer expander.

enable up: Enable up stream port.

enable down: Enable down stream port.

enable sda: Enable system startup counter.

Display Message

None

Related Commands

disable, reset

ExamplesJBOD:>enable down

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

display system status

Syntax Description

Syntax

enable <disk,ps0,ps1,peer,up,down,sda>

Syntax

status

3-8


None

Display Message

None

Related Commands

None

ExamplesJBOD:>status

==============================================================================| JB7 System Status |

==============================================================================

| JB7 SIM Modules Status |

------------------------------------------------------------------------------

SIM[01] status : [ Present ][Self]

SIM[01] temp[01]: [35] C

SIM[01] temp[02]: [30] C

SIM[01] temp[03]: [51] C

SIM[01] volt[01]: [3285] mV

SIM[01] volt[02]: [5044] mV

SIM[01] volt[03]: [11875] mV

SIM[01] volt[04]: [1015] mV

SIM[01] volt[05]: [1818] mV

SIM[02] status : [ Present ][Peer]

SIM[02] temp[01]: [38] C

SIM[02] temp[02]: [34] C

SIM[02] temp[03]: [60] C

SIM[02] volt[01]: [3285] mV

SIM[02] volt[02]: [5018] mV

SIM[02] volt[03]: [11875] mV

SIM[02] volt[04]: [1015] mV

SIM[02] volt[05]: [1804] mV

------------------------------------------------------------------------------

| JB7 MID Modules Status |

------------------------------------------------------------------------------

MID temp[01] : [34] C

MID temp[02] : [33] C

------------------------------------------------------------------------------

| JB7 SPS Modules Status |

------------------------------------------------------------------------------

PS[01] Present : [ Present ]

PS[01] Revision : [05]

PS[01] AC_OK : [OK]

PS[01] PWR_OK : [OK]

PS[01] PS_FAIL : [OK]

PS[01] Temp. : [33] C

PS[02] Present : [ Present ]

PS[02] Revision : [05]

PS[02] AC_OK : [FAIL]

PS[02] PWR_OK : [FAIL]

PS[02] PS_FAIL : [OK]

PS[02] Temp. : [34] C

------------------------------------------------------------------------------

| JB7 FAN Modules Status |

------------------------------------------------------------------------------

PS[01]FAN[01] Status : [3375] rpm => [OK]




3-9


------------------------------------------------------------------------------

| JB7 DISKS Modules Status |

------------------------------------------------------------------------------

Disk[01] status : [Uninstall][Enabled] SAS_ADDR: 0x0000000000000000

Disk[02] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50000842319

Disk[03] status : [ Present ][Enabled] SAS_ADDR: 0x5000c5000722fbb9

Disk[04] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007d813ed

Disk[05] status : [ Present ][Enabled] SAS_ADDR: 0x5000c500048a3c4d

Disk[06] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50008f7fa75

Disk[07] status : [ Present ][Enabled] SAS_ADDR: 0x5000c500048a31cd

Disk[08] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007d8132d

Disk[09] status : [ Present ][Enabled] SAS_ADDR: 0x5000c500048a4ad9

Disk[10] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007d81185

Disk[11] status : [ Present ][Enabled] SAS_ADDR: 0x5000c5000723005d

Disk[12] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007204c15

Disk[13] status : [ Present ][Enabled] SAS_ADDR: 0x5000c5000722dae1

Disk[14] status : [ Present ][Enabled] SAS_ADDR: 0x5000c500048a5821


Disk[16] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007d7e605

Disk[17] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50008f81209

Disk[18] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50008f7fc59



Disk[21] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50008f7f621

Disk[22] status : [ Present ][Enabled] SAS_ADDR: 0x5000c500048a5819

Disk[23] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007d7eb11

Disk[24] status : [ Present ][Enabled] SAS_ADDR: 0x5000c50007d7e849

------------------------------------------------------------------------------

| JB7 State Status |

------------------------------------------------------------------------------

FRU_Error_status : 0x0000000000000000

Self State : 5

Peer State : 5

Interrupt Counter : 3

Interrupt Workaround Counter : 0

EventCounterAfterPowerOn : 0029

EventEraseCounterAfterPowerOn : 0000

SSPCmdCounterAfterPowerOn : 0000

------------------------------------------------------------------------------

Frontend SAS address:

00:0000000000000000

04:0000000000000000

08:0000000000000000

Master SAS Address : 0x500163600053e87d

Slave SAS Address : 0x111111112222223f

display and set system SAS address

Syntax

sas_addr base_addr[0xXXXXXXXXXXXXXXXX]

3-10


Syntax Description

sas_addr: Display system SAS address.

sas_addr [0xXXXXXXXXXXXXXXXX]: Set system SAS address.

Display Message

None

Related Commands

None

ExamplesJBOD:>sas_addr 0x1234567890123456

Please reboot SIM for change SAS address.

JBOD:>sas_addr

SAS Address: 0x1234567890123456

display and set system FAN speed

Syntax Description

rpm: Display system FAN speed.

rpm [1(3440) - 2(4765) - 3(5543)]: Set FAN speed.

Display Message

None

Related Commands

None Examples

JBOD:>rpm 1

[SPS1] FAN #1 set level 1(3440 rpm)




JBOD:>rpm

[SPS1FAN1] speed=3409.




Syntax

rpm level[1(3440) - 2(4765) - 3(5543)]

3-11


display and set system date

Syntax Description

date: Display system date.

date [00-99] [1-12] [1-31] [0-23] [0-59] [0-59]: Set new system date.

Display Message

None

Related Commands

None

ExamplesJBOD:>date 12 10 29 14 23 10

JBOD:>date

Current time: 2012/10/29 14:23:10

display ports information

Syntax Description

port: Display system port information.

Display Message

None

Related Commands

None

ExamplesJBOD:>port

Syntax

date YEAR[00-99] MON[1-12] DATE[1-31] HR[0-23] MIN[0-59] SEC[0-59]

Syntax

port

3-12


------------------------------------------

|Port|01|02|03|04|05|06|07|08|09|10|11|12|

------------------------------------------

|RDY | | | | | | | | | | | | |

------------------------------------------

|SAS | | | | | | | | | | | | |

------------------------------------------

|SATA| | | | | | | | | | | | |

------------------------------------------

|1.5G| | | | | | | | | | | | |

------------------------------------------

|3.0G| | | | | | | | | | | | |

------------------------------------------

|6.0G| | | | | | | | | | | | |

------------------------------------------

Frontend SAS address:

01:0000000000000000 02:0000000000000000 03:0000000000000000 04:0000000000000000

05:0000000000000000 06:0000000000000000 07:0000000000000000 08:0000000000000000

09:0000000000000000 10:0000000000000000 11:0000000000000000 12:0000000000000000

display disks information

Syntax Description

disks: Display system disk information.

Display Message

None

Related Commands

None

ExamplesJBOD:>disks

------------------------------------------------------------------------------

|Disk|01|02|03|04|05|06|07|08|09|10|11|12|13|14|15|16|17|18|19|20|21|22|23|24|

------------------------------------------------------------------------------

|RDY | | V| V| V| V| V| V| V| V| V| V| V| V| V| | V| V| V| | | V| V| V| V|

------------------------------------------------------------------------------

|SAS | | V| V| V| V| V| V| V| V| V| V| V| V| V| | V| V| V| | | V| V| V| V|

------------------------------------------------------------------------------

|SATA| | | | | | | | | | | | | | | | | | | | | | | | |

------------------------------------------------------------------------------

|1.5G| | | | | | | | | | | | | | | | | | | | | | | | |

------------------------------------------------------------------------------

|3.0G| | | V| V| V| V| V| V| V| V| V| V| V| V| | V| V| V| | | V| V| V| V|

------------------------------------------------------------------------------

Syntax

disk

3-13


|6.0G| | V| | | | | | | | | | | | | | | | | | | | | | |

------------------------------------------------------------------------------

Disk SAS address:

01:0000000000000000 02:5000c50000842319 03:5000c5000722fbb9 04:5000c50007d813ed

05:5000c500048a3c4d 06:5000c50008f7fa75 07:5000c500048a31cd 08:5000c50007d8132d

09:5000c500048a4ad9 10:5000c50007d81185 11:5000c5000723005d 12:5000c50007204c15

13:5000c5000722dae1 14:5000c500048a5821 15:0000000000000000 16:5000c50007d7e605

17:5000c50008f81209 18:5000c50008f7fc59 19:0000000000000000 20:0000000000000000

21:5000c50008f7f621 22:5000c500048a5819 23:5000c50007d7eb11 24:5000c50007d7e849

display who is the console management

Syntax Description

who: who is the console management now.

Display Message

None

Related Commands

None

ExamplesJBOD:>who

System Role: SIM1/Master and Dual board

display system version

Syntax Description

ver: Display system version information.

Syntax

who

Syntax

ver

3-14


Display Message

None

Related Commands

None

ExamplesJBOD:>ver

Boot cause : REGISTER_RESET

oooo oooo oooooo oooooooo

88 88 88 88 88 88

88 88ooooo 88 88 88 88

88 88 888 88 88 88 88

o 88 88 888 8o o8 88 88

888 o888ooo88 88oo88 o888oo88

Firmware Version : 1729

Build time : 2011/11/28 10:07:57

Previous Version : 1729

Prev-build time : 2011/11/28 10:07:57

close TCP/IP session

Syntax Description

exit: close TCP/IP session.

Display Message

None

Related Commands

quit

ExamplesJBOD:>exit

display all CLI command

Syntax

exit

3-15


Syntax Description

help: Display system CLI command.

Display Message

None

Related Commands

None

ExamplesJBOD:>help

================================================================================

Description Command

================================================================================

Quit CLI Service quit

Print/Set DHCP Status dhcp <enable,disable>


Zoning configuration zoning <pp,help>

Get/Clear System log syslog clr(option)

Reboot the expander reboot watchdog(optional)

Reset FRU reset <disk,ps0,ps1,peer,up,down,sda>

Disable FRU disable <disk,ps0,ps1,peer,up,down,sda>

Enable FRU enable <disk,ps0,ps1,peer,up,down,sda>

System status status

Set/Get SAS address sas_addr base_addr[0xXXXXXXXXXXXXXXXX]

Set/Get FAN RPM rpm level[1(3440) - 2(4765) - 3(5543)]

Show/Set Date date YEAR[00-99] MON[1-12] DATE[1-31]

HR[0-23] MIN[0-59] SEC[0-59]

Port status port

Disk status disks

Show Mastership who

Show FW version ver

Syntax

help

3-16


Close TCP/IP session exit

CLI Help help command

3-17

CONFIGURE YOUR SYSTEM SYSTEM FIRMWARE UPDATE

3.2 System Firmware UpdateThe Command Line Interface (CLI) is provided to perform system configuration including firmware update.

It’s suggested to use the UART port to communicate with your system when updating firmware. In host side, you can use a serial terminal emulation program. In UART port, the baud rate should be set 115200bps. Before entering CLI, you will need to enter the pass-word 'jbodstorage'.

Note:It’s suggested to do the firmware update with the support from qualified techni-cian. Please make sure you had read all the following instructions before updating the firmware.

It’s suggested to check the following items before firmware update:

Connecting to M4240H’s management (RJ45) or service (RJ11) port

Connection tool: using HyperTerminal in Windows XP or other terminal emulation tool like Tera Term or Putty to build the connection

Firmware for updating

Configuring your serial terminal emulation program1. Double click the Tera Term icon

2. Select New connection... from File drop down menu

3-18

CONFIGURING YOUR SERIAL TERMINAL EMULATION PROGRAM CONFIGURE YOUR SYSTEM

3. Select Serial... from pop-up window

4. Select Serial port... from Setup drop down menu

3-19

CONFIGURE YOUR SYSTEM CONFIGURING YOUR TERMINAL EMULATION PROGRAM

5. Configuring serial terminal emulation program based on the following settings:

6. The connection to your system is built up:

Configuring your terminal emulation program1. Double click the Tera Term icon

3-20

CONFIGURING YOUR TERMINAL EMULATION PROGRAM CONFIGURE YOUR SYSTEM

2. Select New connection... from File drop down menu

3. Select TCP/IP... from pop-up window

4. Configuring terminal emulation program based on the following settings:

3-21

CONFIGURE YOUR SYSTEM INPUT THE PASSWORD TO ENTER COMMAND LINE INTERFACE (CLI) MODE

5. The connection to your system is built up:

Input the password to enter command line interface (CLI) mode

Your system provides a basic command line interface (CLI) as an alternative for users to configure.

1. Launch serial terminal emulation program and building up the connection to sys-tem

2. Type the password “jbodstorage.”

3. The message “Enter Service Console.” will show.

3-22

CHECK YOUR FIRMWARE VERSION CONFIGURE YOUR SYSTEM

Check your firmware version1. Launch serial terminal emulation program and building up the connection to sys-

tem



4. Type “ver” in command prompt then press enter to list the current revision

Note:If firmware version is 1729 or higher, an update is unneccessary, exit this program.

3-23

CONFIGURE YOUR SYSTEM UPDATE YOUR SYSTEM FIRMWARE

Update your system firmware

Note:If firmware version is less than 1729, an update is neccessary, please check with your service provider first and refer to the following instructions.

1. Launch serial terminal emulation program and building up the connection to sys-tem



4. Type firmware update command: “fdl e1 0 y” in command prompt

5. Follow the on screen instruction

3-24

UPDATE YOUR SYSTEM FIRMWARE CONFIGURE YOUR SYSTEM

6. Select File>Transfer>XMODEM>Send to upload firmware file

7. The browse window will pop up.

3-25

CONFIGURE YOUR SYSTEM UPDATE YOUR SYSTEM FIRMWARE

8. Select the firmware file.

9. Click “Open” to begin uploading the firmware.

3-26

UPDATE YOUR SYSTEM FIRMWARE CONFIGURE YOUR SYSTEM

10. check the status screen as shown.

11. Command prompt will show again when upload process is complete.

12. Type “reboot” to reboot your system with new firmware when firmware update is finished.

3-27

JB7-4U...INTRODUCTION ABOUT YOUR SYSTEM 1-1 1.1 Introduction MESOS M4240H is a 4U storage server...

Documents

Transcript of JB7-4U...INTRODUCTION ABOUT YOUR SYSTEM 1-1 1.1 Introduction MESOS M4240H is a 4U storage server...