Instrument catalog

Surgical Instrument CatalogJuly/2003

Medtronic Ophthalmic Products

OCUTEKTM BrandOphthalmic Instruments NOW Makes Them Available To You!

Centuries of craftsmanship are distilled

into the finest ophthalmic instruments

in the world. Each instrument starts as a

high quality forging. From these forgings,

master craftsmen create the most precise

and reliable surgical instruments that

exceed your highest standards.

Only holders of the coveted

Meisterbrief certificate, which requires an

eight-year apprenticeship, are qualified

to become OCUTEK instrument makers

assuring you the highest quality instruments.

For Over a Hundred years

GermanMasterInstrumentMakershave crafted the finest

Surgical Instruments

In the World.

Medtronic Ophthalmic Instrument Catalog

Care and Handling Instructionsfor OCUTEKTM Brand and other

Medtronic Ophthalmic Surgical Instruments

Description

Manual surgical instruments are intended for use invarious surgical procedures. It is the responsibility of thesurgical team to select the appropriate instruments foreach case. Do not use these instruments for purposesother than intended. Instruments must be cleaned andsterilized prior to first use and before each reuse.

Cleaning:1) Promptly and thoroughly rinse instruments withdeionized water after each use.

2) Disassemble instruments as necessary. Soak in luke-warm (less than 110°F/43°C) mild enzymatic detergent,pH 7.0 8.5, and deionized water for at least 30 seconds.Rinse thoroughly with deionized water and wipe dry.

Additional Cleaning Methods:

Presoak in 3% hydrogen peroxide.

Additional thorough scrubbing with a soft instrumentbrush while the instrument is submerged in cleaningsolution may be warranted.

Additional Cleaning Methods:

The following cycle has been validated by MedtronicSOLAN: Steam Sterilization: Temp.: 250°F (121°C)Time: 30 minutes.

Alternately, any validated steam sterilization processwith temperatures up to 275°F (135°C) may be used.

It is the responsibility of each health care facility to val-idate all sterilization processes with their particularequipment and procedures to assure sterility.

COLD SOAK IN GLUTARALDEHYDE, CHLORINE, ORAMMONIUM SOLUTIONS OR DRY HEAT STERILIZA-TION ARE NOT RECOMMENDED BECAUSE DAMAGETO THE INSTRUMENT FINISH MAY OCCUR.

Repairs and Service:

For repair and service of Medtronic and OCUTEKInstruments, contact the distributor from whom theproduct was purchased or Medtronic Ophthalmics:

Toll Free: 1-800-535-4646 1-904-296-9600


TA B L E O F C ON T E N T SInformation in this catalog is presented in alphabetical order,

first by Product Group, arid then by Product Name within the group.

page 4

Ophthalmic Instrument Catalog


Blade Breakers and Holders . . . . . . . . . . . . pg. 7Calapers, Guages and Rulers . . . . . . . . . . pg. 8Cannulas and Cyctotomes . . . . . . . . . . . . . pg. 10Corneal/ Misc Markers . . . . . . . . . . . . . . . . pg. 15Curettes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 16Forceps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 17

Capsule . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 17Capsulorhexis . . . . . . . . . . . . . . . . . . . . . . pg. 18Cilia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 19Corneal . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 20Dressing . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 22Fixation . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 22Foreign Body . . . . . . . . . . . . . . . . . . . . . . . pg. 24Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 25Jeweler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 28Mosquito . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 29Muscle . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 30Retinal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 30Suturing . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 32Tissue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 32Towel Clamps . . . . . . . . . . . . . . . . . . . . . . pg. 34Tying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 35Tying and IOL . . . . . . . . . . . . . . . . . . . . . pg. 37Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 38Miscellaneous . . . . . . . . . . . . . . . . . . . . . . pg. 38

Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 38Fixation . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 39IOL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 40Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 42Muscle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 44

Knives, Cystotomes, Dissectors . . . . . . . pg. 44Lens Loops and Spoons . . . . . . . . . . . . . . . pg. 47Needle Holders . . . . . . . . . . . . . . . . . . . . . . . pg. 49Nucleus Manipulators / Dividers . . . . . . . pg. 52

Probes and Dialators . . . . . . . . . . . . . . . . . . . . . pg. 52Retina Picks, Hooks, Spatulas . . . . . . . . . . . . . pg. 57Retractors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 58

Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 58Lacrimal Sac . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 58Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 59Orbital . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 59

Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 60Globe Fixation . . . . . . . . . . . . . . . . . . . . . . . . . pg. 60

Sissors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 61Capsulotomy . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 61Corneal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 62Corneal Section . . . . . . . . . . . . . . . . . . . . . . . pg. 63Enucleation . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 65Foreign Body . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 65Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 65Retinal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 67Stitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 67Strabismus . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 67Tenotomy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 68Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 69Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . pg. 70

Scleral Depressors . . . . . . . . . . . . . . . . . . . . . . . pg. 70Scrapers and Polishers . . . . . . . . . . . . . . . . . . . pg. 71Snares and Spoons . . . . . . . . . . . . . . . . . . . . . . . pg. 72 Spatulas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 72Specula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 74Titanium . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 79Trephines and Punches . . . . . . . . . . . . . . . . . . . pg. 85

Punches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 86Trephine Blades . . . . . . . . . . . . . . . . . . . . . . . pg. 86Trephine Handles . . . . . . . . . . . . . . . . . . . . . . pg. 87

Diamond Knives . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 88

Click oninstrument nameto go directly to catalog section.



page 5


To Place an Order

Medtronic ophthalmic products are available worldwide

through exclusive, authorized distributors. (In Canada,

France, the United Kingdom, Australia and Germany,

Medtronic products are available through Medtronic

ophthalmic product representatives.) For the name of the

distributor servicing your area, please contact the

Medtronic Ophthalmics Customer Service Department.

Pricing

Medtronic reserves the right to change prices without

notice. Shipping policy and charges are at the discretion of

the distributor. Please contact your representative or dis-

tributor for price and shipping

Warranty

All Medtronic ophthalmic products are warranted to be

free from defects in material and workmanship. Any

product failing, as a result of such defect, will be repaired

or replaced at the discretion of Medtronic. All returns

should be made to Medtronic or the distributor from

whom the product was purchased. This warranty is void if

the product is abused, altered, modified, or is not used in

the manner for which it is intended. no other warranty is

implied or authorized without the written consent of

Medtronic.

Service and Repair

For service and repair of Medtronic and OCUTEKTM

Instruments, and DIAMONTEKTM Diamond Knives,

contact the distributor from whom the product was

purchased, or Medtronic Ophthalmics Customer Service.

Specifications

Photography and drawings contained in the catalog

are for illustrative purposes only. While every attempt

was made to accurately represent the product, the pho-

tograph or drawing of the product may not be actual size.

Medtronic reserves the right to alter our patterns and

make modifications to any product at any time

without notice.

Customer Service

For further information regarking the use of Medtronic

products or to report any problems, please contact:

Medtronic Ophthalmic Products

Customer Service Department

6743 Southpoint Drive North

Jacksonville FL 32216

800-535-4646 / 800-296-9600

Fax 904-279-2630

International Customer Service

International customers may contact their local Medtronic

Ophthalmic Product office, or local distributor, at the

following numbers:

Australia: . . . . . . . . . . . . . . . . . . . . 800-062-289

Canada . . . . . . . . . . . . . . . . . . . . . 800-217-1617

France . . . . . . . . . . . . . . . . . . . . . . . 0169-187400

Germany . . . . . . . . . . . . . . . . . . . 08105-3755-0

U.K. . . . . . . . . . . . . . . . . . . . . . . . . 01344-750255

G E N E R A L I N F O R M AT ION

MEISTERBRIEFGERMAN PRECISION

The Finest Surgical Instruments in the World

Only holders of the coveted Meisterbrief Certificate,which requires an eight year apprenticeship,

are qualified to become OCUTEK® instrument makers.

� are trademarks and ® are registered marks of Medtronic Opthalmics, a division of Medtronic USA, Inc.

BLADE BREAKERS AND HOLDERS

BARRAQUER BLADE BREAKER AND HOLDER

12mm, straight, smooth, flat jaws. Flat, serrated handle withspring lock. Overall length 108mm.

#1510

CASTROVIEJO BLADE BREAKER AND HOLDER

12mm, super slim jaws. Round handle with end lock. Overalllength 125mm.

#1502

CASTROVIEJO BLADE BREAKER AND HOLDER

Slim Model 12mm, smooth, pointed jaws. Round handle with slidelock. Overall length 120mm.

#1501

OCUTEK MICRO BLADE HOLDER

10mm, smooth, thin, flat jaws. Round handle with twist lock.Overall length 103mm.

#1503

STAINLESS STEEL BREAKABLE BLADES

Double edge, stainless steel blades designed to break cleanly.Individually wrapped. 10 blades per box.

#1511

SWISS BLADE BREAKER AND HOLDER

13mm, conical, smooth jaws. Round handle with end lock. Overalllength 120mm.

#1505


page 7


CALAPERS, GUAGES AND RULERS

CASTROVIEJO CALIPER

Graduated in one millimeter increments from 1mm to 20mm.Thumbscrew holds tips apart at desired setting. Overall length55mm.

#7700 Straight shafts.#7701 Curved shafts.

JAMESON CALIPER

Graduated in one millimeter increments from 0mm to 80mm andin 1/16 inch increments up to 3 inches. Straight shafts. Featuresthumbscrew for locking at desired settings.

#7710

MENDEZ DEGREE GAUGE

Ring gauge calibrated every 10° from 0° to 180°. Flat, serratedhandle. Overall length 108mm. Used for accurate alignment ofcorneal incisions for correction of astigmatism.

#1782

MENDEZ DEGREE GAUGE � TITANIUM

Ring gauge calibrated every 10° from 0° to 180°. Round, knurledhandle. Overall length 108mm. Used for accurate alignment ofcorneal incisions for correction of astigmatism. Made of high-grade, lightweight titanium.

#0536

STAHL CALIPER

Anterior chamber caliper designed for measuring corneal diame-ter.

#7706

STAINLESS STEEL FLEXIBLE RULER

Measures up to 152mm in one millimeter increments and up to 6inches in 1/32 inch increments.

#7720

page 8




CALAPERS, GUAGES AND RULERS

THORPE CALIPER

Graduated in one millimeter increments from 0mm to 80mmand in 1/16 inch increments up to 3 inches. Angled shafts withangled tips. Features thumbscrew for locking at desired setting.Overall length 122mm.

#7712

AIR INJECTION CANNULA

Cannulated shaft angled 5mm from shaft tip. Shaft length23mm.

#6500 30 gauge cannulated shaft.#6502 27 gauge cannulated shaft.

ATKINSON RETROBULBAR NEEDLE

Straight, cannulated shaft with sharp, beveled tip. Shaft length36mm.

#6510 23 gauge.#6511 25 gauge.

BINKHORST IRRIGATING CANNULA

22 gauge, cannulated shaft with �J� shaped, smooth, blunt tip andfront opening. Shaft length 28mm.

#6617 Straight shaft.#6618 Angled right shaft.#6619 Angled left shaft.

BISHOP-HARMON ANTERIOR CHAMBER IRRIGATOR

#6600 Set includes autoclavable silicone bulb, cannula adaptor and 19 gauge angled cannula.

#6610 Silicone bulb for 6600#6615 Cannula adaptor for 6600#6620 19 guage irrigation cannula for 6600.

Shaft length 26mm.


page 9


CANNULAS AND CYCTOTOMES

DANKNER PANARIELLO 12 O� CLOCK CORTEX CANNULA

Curved, 23 gauge, cannulated shaft with 0.4mm side aspiration port. Shaft length 24mm.

#6637 Allows for easy aspiration of 12 o�clock cortex throughside port incision.

DOUGHERTY ANTERIOR CHAMBER IRRIGATOR

Glass irrigating cannula with blue tip. Shaft length 48mm.

#6626

DREWS CYSTOTOME

4mm length from hub to first 80° bend, 3mm length from firstto second 50° bend, 8mm length from second bend to shaft tip. Shaft length 15mm.


GILLS CANNULA

Angled, 25 gauge, cannulated shaft with smooth, blunt tip.

#6633 Angled 5mm from shaft tip.#6634 Angled 7mm from shaft tip.#6635 Angled 8mm from shaft tip.#6636 Angled 10mm from shaft tip.

GILLS-WELSH DOUBLE-BARREL CANNULA

Irrigating-Aspirating CannulaAngled, 25 gauge, cannulated shaft at working end. Cannulashaft length 22mm. Silicone tubing 300mm. Overall length371mm.

#6452

GIMBLE IRRIGATING CANNULA

30 gauge cannulated shaft with �U�-shaped tip. Shaft length 29mm. Ideal for hydrodissection of the lens nucleus.

#6651

JENSEN-THOMAS IRRIGATING-ASPIRATING CANNULA

Double-barreled irrigation-aspiration unit, 23 gauge. Side irriga-tion and aspiration ports. Shaft length 33mm. Silicone tubinglength 379mm. Overall length 445mm.

#6422

page 10





KELLAN HYDRODISSECTION CANNULA

Gently curved, 25 gauge, cannulated shaft with blunt tip. Shaftlength 19mm.

#6643

KELMAN CANNULATED CYSTOTOME

22 gauge, cannulated shaft. Shaft length 32mm.

#6640 Sharp Tip.#6642 Blunt Tip

KNOLLE ANTERIOR CHAMBER CANNULA

Angled 2mm from blunt, shaft tip. Shaft length 21mm.

#6612 30 gauge cannulated shaft.#6613 25 gauge cannulated shaft.#6614 23 gauge cannulated shaft.

KNOLLE-KELMAN CYSTOTOME

22 guage, cannulated shaft with sharp tip. Shaft length 32mm.

#6437

KRATZ CYSTOTOME

22 gauge, formed, cannulated shaft with sharp tip. 5mm lengthfrom hub to angle, 12mm from angle to shaft tip. Shaft length18mm.

#6438

LEWICKY CORTEX EXTRACTOR

Curved, 23 gauge, cannulated shaft with aspiration port set at45°. Shaft length 13mm

#6638 Aspiration port set at 45° right.#6639 Aspiration port set at 45° left.

LIEPPEMAN CYSTOTOME

Micro cystotome with angled 22 gauge cannulated shaft.Supplied with guard to protect sharp, cutting tip. Shaft length11mm.

#6463

MALE TO MALE CANNULA ADAPTOR

DERLIN® male luer adaptor designed to connect aspiration can-nulas with aspiration tubing. Overall length 35mm.

#6698


page 11



MAUMENEE VITREOUS ASPIRATING NEEDLE

18 gauge cannulated shaft with blunt tip. Markings on shaft at5mm, 10mm and 15mm from hub. Length 25mm.

#6608

MCINTYRE ANTERIOR CHAMBER CANNULA

Smooth, blunt tip. Shaft length 18mm.

#6602 Straight, 23 gauge cannulated shaft.#6603 Angled, 23 gauge cannulated shaft.#6604 Straight, 26 gauge cannulated shaft.#6605 Angled, 26 gauge cannulated shaft.#6606 Straight, 30 gauge cannulated shaft.#6607 Angled, 30 gauge cannulated shaft.

MCINTYRE COAXIAL IRRIGATING-ASPIRATING SYSTEM

System includes one each 6464, 6467, and 6469. Overall length65mm.

#6470 Complete.

MCINTYRE INNER CANNULA

23 gauge, cannulated shaft. Shaft length 46mm. Component ofMcIntyre Coaxial Irrigating-Aspirating System (6470).

#6464 0.2mm side port.#6465 0.3mm side port.#6466 Front opening.

MCINTYRE OUTER CANNULA

19 gauge cannulated shaft. Shaft length 17mm. Component ofMcIntyre Coaxial Irrigating-Aspirating System (6470)

#6467 Truncated tip with dual 0.5mm side openings.#6468 Straight, blunt tip with front opening.

MCINTYRE NYLON CONNECTOR

Autoclavable nylon connector designed to couple McIntyre innerand outer cannulas to comprise McIntyre Coaxial I/A System(6470). Overall length 16mm.

#6469

MCINTYRE INFUSION HANDLE

Aspirating or irrigating handpiece made of autoclavable plastic.Luer connector fits all cannula hubs. Narrow connector fits IVtubing. Overall length 76mm.

#6699

page 12





MCINTYRE LACRIMAL CANNULA

23 gauge, cannulated shaft with blunt tip and side port. Shaftlength 46mm.

#6305 Straight shaft. #6306Curved shaft.

NEVYAS DOUBLE SHARP CYSTOTOME

22, gauge, cannulated shaft with sharp front and back edges.Shaft length 34mm.

#6421

NICHAMIN HYDRODISSECTION CANNULA

Angled, cannulated shaft with flattened tip. 28mm.

#6652 25 gauge.#6653 27 gauge.

OCUTEK HYDRODISSECTION CANNULA

Angled, cannulated shaft with �U� shaped tip. Ideal for hydrodis-section of the lens nucleus. Shaft length 28mm.

#6644 25 gauge shaft, angled left.#6645 25 gauge shaft, angled right.#6646 25 gauge shaft, straight.#6647 27 gauge shaft, angled left.#6648 27 gauge shaft, angled right.#6649 27 gauge shaft, straight.

OCUTEK LACRIMAL CANNULA

Straight, 23 gauge, cannulated shaft with blunt tip. 31mm.

#6303

OCUTEK LACRIMAL CANNULA-REINFORCED

23 gauge, reinforced, cannulated shaft. Shaft length 30mm.

#6300 Curved tip. #6301 Straight tip.

OSHER �J� CANNULA

27 gauge, cannulated shaft with �J�-shaped tip. Shaft length27mm.

#6629 Allows for each 12 o�clock cortical cleanup. Equallyeffective with viscoelastics as well as balanced salt solution.


page 13



SCHEIE ANTERIOR CHAMBER CANNULA

Straight, 27 gauge, cannulated shaft with blunt tip. Shaft length20mm.

#6616

SIMOCE CORTEX EXTRACTOR

Curved, 23 ga, cannulated shaft with side aspiration port.

#6428 Shaft length 12mm.#6428L Shaft length 21mm.

SIMCOE DOUBLE-BARRELED

Irrigating-Aspirating Unit23 gauge, double-barreled irrigation-aspiration unit. Thin wallwith 0.3mm aspiration port. 13mm cannula shaft length. Siliconetubing length 300mm. Overall length 355mm.

#6449 Irrigation through mail hub, aspiration through silicone tubing.

SIMCOE REVERSE DOUBLE-BARRELED

Irrigating-Aspirating Unit23 gauge double-barreled irrigation-aspiration unit. Thin wall with0.3mm aspiration port. Aspiration shaft length 17mm, irrigationshaft length 15mm. Silicone tubing length 392mm. Overalllength 427mm.

#6449R Irrigation through silicone tubing,aspiration through mail hub.

THURMOND TWO-WAY AIR BUBBLE REMOVAL CANNULA

Curved, 21 gauge, cannulated shaft at working end. Cannulashaft length 37mm. Silicone tubing length 30 cm. Overall length34.6 cm.

#6433

TROUTMAN ALPHA-CHYMOTRYSPIN CANNULA

Curved, 25 gauge, cannulated shaft with smooth bulbous tip.Shaft length 31mm.

#6400

page 14





WELSH CORTEX EXTRACTOR

25 gauge, cannulated shaft with olive tip. Length 23mm.

#6435 Angled right. Allows for 3 o�clock cortical cleanup.

#6436 Angled left. Allows for 9 o�clock cortical cleanup.#6440 Straight. Allows for 6 o�clock cortical cleanup.

CORNEAL/MISC MARKERS

ANIS SUTURE PLACEMENT MARKER

8 bladed radial marker with 8mm center opening. Flat, smoothhandle. Overall length 105mm.

#2648

HOFFER OPTICAL ZONE MARKER

Ring marker with extra fine cross hairs to provide location of theoptical center. Round, knurled handle. Overall length 103mm.

#1560 3.0mm #1561 3.25mm #1562 3.5mm #1563 3.75mm #1564 4.0mm #1565 4.25mm #1566 4.5mm #1567 4.75mm #1568 5.0mm #1573 6.0mm #1575 8.0mm #1576 5.5mm

OCUTEK RADIAL MARKER

Blade marker with inner blade diameter of 3mm. Round, knurledhandle. Overall length 105mm. Designed to allow marking ofcornea during radial keratotomy with minimal applied pressure.

#7111 8 bladed radial marker.#7112 4 bladed radial marker.

OCUTEK TRIPLE OPTICAL ZONE MARKER

Ring marker with 3 concentric rings measuring 3.0mm, 5.0mmand 7.0mm. Flat, smooth handle. Overall length 100mm.

#1580

THORNTON ARCUATE MARKER

Ring marker with marking blades set at 10° increments. Round,knurled handle. Overall length 96mm. Designed for 6 to 8mmoptical zones. Impresses a 360° line pattern in 10° increments onthe cornea for astigmatic keratotomy. Can be used with MendezDegree Gauge.

#7130 With target.#7131 Without target.


page 15


CORNEAL/MISC MARKERS

THORNTON DOUBLE CORNEAL RULER

Parallel markers with central opening for visual axis alignment.Round, knurled handle. Overall length 99mm. Used to impressa symmetrical pattern of ruled markings on the cornea forplacement of transverse incisions from 0.5mm to 5.0mm inlength.

#7132 6-8mm optic zones.#7133 5-7 optic zones.

THORNTON LOW PROFILE OPTICAL ZONE MARKER

Low profile ring marker with centering pin to provide location ofoptical center. Low profile helps eliminate visual distortion.Round, knurled handle. Overall length 103mm.

#7113 3mm #7114 3.25mm #7115 3.5mm #7116 3.75mm #7117 4.0mm #7121 5.0mm #7122 6.0mm #7123 4.25mm #7124 4.5mm #7125 4.75mm

SINSKEY HOOK II

Angled shaft with 0.2mm, angled tip. Round, knurled handle.Overall length 119mm. Used to mark the visual axis and reopenRK incisions.

#7006

SINSKEY IRIS AND IOL HOOK

Straight shaft with 0.2mm, angled tip. Round, knurled handle.Overall length 117mm. Used to mark the visual axis and reopenRK incisions.

#7616

CURETTES

FOREIGN BODY CURETTE

Flat, smooth handle. Overall length 126mm.

#7140 0.5mm diameter cup.#7141 1.0mm diameter cup

page 16




CURETTES

HEATH CHALAZION CURETTE

Ring style curette. Round Handle. Overall length 131mm.

#7091 Size 1.1mm diameter ring.#7092 Size 2 2mm diameter ring.#7093 Size 3 3mm diameter ring.

MEYERHOFFER CHALAZION CURETTE

Flat smooth handle. Overall length 130mm.

#7100Size 0 1.5mm diameter cup.#7101 Size 1 1.7mm diameter cup.#7102Size 2 2.2mm diameter cup.#7103Size 3 2.5mm diameter cup.#7104Size 4 3.0mm diameter cup.

SKEELE CURETTE

2mm cup with serrated edge. Flat smooth handle. Overall length125mm.

#7090

FORCEPS

ARRUGA CURVED CAPSULE FORCEPS

Standard, curved shafts with 2.75mm x 1.35mm cupped tips.Wide, flat, serrated handle with iris stop. Overall length 108mm.

#3750

CASTROVIEJO CROSS ACTION CAPSULE FORCEPS

45° angled shafts with 2.75mm x 1.35mm cupped tips. Wide, flat,serrated, cross action handle. Overall length 108mm.

#3760

KANSAS NUCLEAR FRAGMENT FORCEPS

Angled shafts with conical, serrated jaws. Standard, fenestratedhandle. Overall length 113mm. Designed for extracting lens nucle-us fragments through a small incision.

#3762

OSHER CAPSULE-FOREIGN BODY FORCEPS

60°angled jaws featuring fine, 8mm platforms. Flat, serratedhandle. Overall length 102mm.

#3764


page 17


FORCEPS

INAMURA CAPSULORHEXIS FORCEPS � TITANIUM

45° angled shafts with angled tips. Flat, serrated, fenestrated,cross action handle. Made of high-grade, lightweight titanium.Overall length 105mm. 2.0mm cross action shaft ideal for workingin small incision environment.

#0129

LEHNER-UTRATA CAPSULORHEXIS FORCEPS

Utrata-like, fine, angled tips with gently curved shaft for per-forming capsulorhexis through tunnel incisions.

#3589 Flat, serrated handle. Overall length 102mm.

#3590 Round knurled handle. Overall length 114mm.

O�GAWA-UTRATA CAPSULORHEXIS FORCEPS

Very delicate, angled tips designed for grasping capsule tissue.Iris stop reduces concern for pinching iris while performing cap-sulorhexis. Round handle for fingertip rotational control. Overalllength 112mm.

#3588

UTRATA CAPSULORHEXIS FORCEPS,

Flat Handle � Titanium45° angled shafts with angled tips. Iris stops 8.5mm from tip.Flat, serrated, fenestrated handle. Made of high-grade, light-weight titanium. Overall length 83mm.

#0128

UTRATA CAPSULORHEXIS FORCEPS,

Round Handle � Titanium45° angled shafts with angled tips. Iris stops 8.5mm from tip.Round, knurled handle. Made of high-grade, lightweight titanium.Overall length 115mm.

#0127

UTRATA CAPSULORHEXIS FORCEPS

Angled shaft with very delicate, angled tips designed for graspingcapsule tissue. Iris stop reduces concern of pinching iris whileperforming capsulorhexis. Overall length 101mm.

#3583 Flat, serrated handle.#3584 Round, knurled handle.

page 18




FORCEPS

BAIRD CHALAZION FORCEPS

Oval, 13mm X 11mm, solid lower plate with oval, 11mm X 8mm(inside dimensions), fenestrated upper plate. Flat, serrated han-dle with locking thumb screw mechanism. Overall length 97mm.

#3875

DESMARRES CHALAZION FORCEPS

Oval, solid lower plate with fenestrated upper plate. Flat, serrat-ed handle with locking thumb screw mechanism. Overall length90mm.

#3870 Large.#3871 Medium.#3872 Small.

ERHARDT LID FORCEPS

14mm X 26mm oval lower plate with 9mm., two pronged, upperserrated jaw. Flat, serrated handle with locking thumb screwmechanism. Overall length 90mm.

#3888

FRANCIS CHALAZION FORCEPS

Oval, 17mm, solid lower plate with oval, 14mm X 12mm (insidedimensions), fenestrated upper plate. Flat, serrated handle withlocking thumb screw mechanism. Overall length 99mm.

#3864

HEATH CHALAZION FORCEPS

Oval, 16mm, solid lower plate with oval, 12mm X 14mm (insidedimensions), fenestrated upper plate. Flat, serrated handle withlocking thumb screw mechanism. Overall length 99mm.

#3868

HUNT CHALAZION FORCEPS

Round, 15mm, solid lower plate with round, 12mm inner diameter,fenestrated upper plate. Flat, serrated handle with locking thumbscrew mechanism. Overall length 99mm

#3866

LAMBERT CHALAZION FORCEPS

Round, 10mm, solid lower plate with round, 8mm inner diameter,fenestrated upper plate. Flat, serrated handle with locking thumbscrew mechanism. Length 92mm.

#3880


page 19




FORCEPS

SNELLEN ENTROPIAN FORCEPS

28mm, solid, lower plate. Open upper plate. Flat, serrated han-dle with locking thumb screw mechanism. Overall length 88mm.

#3881 Left. #3882 Right.

WIES CHALAZION FORCEPS

Stirrup shaped, 15mm wide, solid lower plate. Fenestrated andserrated upper plate with 12mm by 9mm inside dimensions. Flat,serrated handle with locking thumb screw mechanism. Overalllength 96mm.

#3860

BARRAQUER CILIA FORCEPS

Straight shafts with slightly curved, 6mm, platformed tips. Flat,serrated handle. Overall length 103mm.

#3700

GRADLE CILIA FORCEPS

Straight shafts with smooth, squared off, positive gripping jaws.Cross action, spring handle. Overall length 97mm.

#3702

OCUTEK CILIA FORCEPS

Straight shafts with 1mm X 3mm smooth, platformed tips. Flat,serrated handle. Overall length 75mm.

#3706

CASTROVIEJO-COLIBRI CORNEAL FORCEPS

Curved shafts. Angled tips feature 1 x 2, 0.12mm teeth. Wide,serrated handle. Overall length 108mm.

#3212

COLIBRI CORNEAL UTILITY FORCEPS

Curved shafts. Angled tips feature 1 x 2, 0.12mm teeth. Overalllength 75mm.

#3210


FORCEPS

GIRARD CORNEOSCLERAL FORCEPS

Curved shafts with 6mm tying platforms. Angled tips feature 1 x2, 0.12mm teeth. Overall length 102mm.

#3380 Right handed.#3381 Left handed.

GIRARD CORNEOSCLERAL FORCEPS

Straight shafts with tying platforms and smooth tips. Roundhandle. Overall length 104mm.

#3390

HARMS-COLIBRI CORNEAL UTILITY FORCEPS

Straight shafts. Angled tips feature 1 x 2, 0.12mm teeth withtying platforms. Colibri style handle. Overall length 73mm.

#3214

HYDE CORNEAL FORCEPS

Curved shafts. Angled tips feature 2 x 2, 0.12mm teeth withtying platforms. Wide, serrated handle. Overall length 105mm.Also known as University of Kansas Corneal Forceps.

#3215

MAUMENEE-COLIBRI CORNEAL FORCEPS

Curved shafts. Angled tips feature 1 x 2, 0.12mm teeth withtying platforms. Flat, serrated, cross-action handle. Overalllength 102mm.

#3457

POLACK DOUBLE CORNEAL FORCEPS

Curved shafts. Angled tips feature two sets of 1 x 2, 0.12mmteeth separated by 1mm. Flat, serrated handle. Overall length75mm.

#3470

TROTMAN BARRAQUER COLIBRI FORCEPS � TITANIUM

Curved shafts with angled tips. Tips feature 0.12mm, 1 x 2 teeth.Colibri-style, fenestrated handle. Made of high-grade, light-weight titanium. Overall length 78mm.

#0116


page 21


FORCEPS

DRESSING FORCEPS � CURVED

Serrated tips. Flat, serrated handle. Overall length 105mm.

#3262 Slightly curved shafts with delicate tips.#3263 Strongly curved shafts with delicate tips.#3265 Curved shafts with standard tips.

DRESSING FORCEPS � STRAIGHT

Straight shafts with serrated tips. Flat, serrated handle. Overalllength 100mm.

#3260 Delicate tips#3264 Standard tips

ARROWSMITH CORNEAL FIXATION FORCEPS

Tips feature two point fixation with two sets of 1 x 2, 0.12mmteeth. 8mm spread between tips. Wide, flat, serrated handle with lock. Overall length 104mm.

#3028 Straight shafts.#3029 Angled shafts.

BORES CORNEAL FIXATION FORCEPS

Straight shafts. Tips feature two point fixation with two sets of 1x 2, 0.12mm teeth. 3mm spread between tips. Wide, flat, fenes-trated handle. Overall length 105mm.

#3025

BRACKEN FIXATION FORCEPS

Straight shafts. Tips feature 1 x 2, 0.7mm teeth. Flat, serrated handle. Overall length 99mm.

#3247

BRACKEN-FARKAS CORNEAL FORCEPS

Straight shafts. Tips feature 1 x 2, 0.12mm teeth. Flat, serrated handle. Overall length 102mm.

#3249

page 22




FORCEPS

ELSCHNIG FIXATION FORCEPS

Straight shafts. Tips feature 1 x 2, 2.0mm, angled teeth. Flat,serrated handle. Overall length 103mm.

#3244 Narrow handle.#3245 Wide handle.

GRAEFE FIXATION FORCEPS

Straight shafts with flared jaws featuring two rows of fine teeth.Flat, serrated handle. Overall length 111mm.

#3500 4.5mm jaws. Standard handle.#3501 4.5mm jaws. Locking handle.#3504 3.5mm jaws. Standard handle.

GREEN FIXATION FORCEPS

Straight shafts. Tips feature two horizontal rows of opposingteeth. Flat, serrated handle. Overall length 100mm. Ideal forsecure fixation of ocular structures.

#3356 5mm jaws.#3357 10mm jaws.

HOFFMAN POLACK FIXATION FORCEPS � TITANIUM

Curved shafts. Angled tips feature two sets of 1 x 2, 0.12mmteeth separated by 1.6mm. Round, cross-action handle with lock.Made of high-grade, lightweight titanium. Overall length127mm.

#0117

KREMER FIXATION FORCEPS

Tips feature two point fixation with two sets of 1 x 2, 0.12mmteeth. 13mm spread between tips. Wide, flat, serrated handlewith lock. Overall length 107mm.



page 23


FORCEPS

KUHNT FIXATION FORCEPS

Straight shafts. Tips feature 1 x 2, angled teeth. Flat, serratedhandle. Overall length 110mm.

#3354

LESTER FIXATION FORCEPS

Straight shafts with toothed tips. Flst, serrated handle. Overalllength 96mm.

#3350 1 x 2 teeth #3352 2 x 3 teeth

RUBMAN-BORES CORNEAL FIXATION FORCEPS

Angled shafts. Tips feature two point fixation with two sets of 1x 2, 0.12mm teeth. 3mm spread between tips. Wide, flat, ser-rated handle. Overall length 104mm.

#3026

THORPE CONJUNCTIVAL FIXATION FORCEPS

Straight shafts with tying platforms. Tips feature 2 x 3, 0.12mmteeth. Flat, serrated handle. Overall length 94mm.

#3360

OCUTEK INTRAOCULAR FORCEPS

Straight, tubular shaft. Squeeze handle. Overall length 147mm.

#3844 1.5mm oval cupped jaws.#3845 3.0mm serrated jaw.

SCHAAF FOREIGN BODY FORCEPS

Curved shafts with grooved jaws. Flat, fenestrated handle.Overall length 105mm.

#3720

WILSON VITREOUS FOREIGN BODY FORCEPS

Straight, 20 gauge diameter shaft. Three, 2mm prongs with0.1mm angled tips. Squeeze handle. Overall length 84mm.

#3480

Medtronic Ophthalmic Instrument Catalog page 24

Ophthalmic Instrument CatalogOphthalmic Instrument Catalog

FORCEPS

ANIS LENS HOLDING FORCEPS

Angled shafts with smooth tips. Knurled, round, spring handle.Overall length 115mm.

#3033

BARRETT LENS FOLDING FORCEPS � TITANIUM

20° angled shafts. Flat, serrated, fenestrated, cross-action han-dle. Made of high-grade, lightweight titanium. Overall length105mm.

#0132

BARRETT LENS HOLDING FORCEPS � TITANIUM

30° angled shafts with 10mm, curved jaws. Flat, serrated, fenes-trated, reverse, cross-action handle. Made of high-grade, light-weight titanium. Overall length 115mm.

#0133

BECHERT LENS HOLDING FORCEPS

Curved shafts with delicate, flat, smooth tips. Flat, serrated,spring handle. Overall length 119mm.

#3040

BECHERT-MCPHERSON TYING FORCEPS

Angled shafts. Jaws feature 10mm tying platforms and smoothtips. Flat, serrated handle. Overall length 83mm.

#3546

BLAYDES LENS HOLDING FORCEPS

Angled shaft with smooth tips. Flat, serrated, spring handle.Overall length 111mm.

#3032

CLAYMAN LENS HOLDING FORCEPS

Curved shafts with angled tips. Flat, serrated, spring handle.Overall length 128mm.

#3530




page 25


FORCEPS

DODICK INTRAOCULAR LENS FORCEPS

Offset, angled shafts with smooth tips. Flat, serrated handle.Overall length 101mm.

#3543 Angled left. #3544 Angled right.

FAULKNER LENS FOLDING FORCEPS

Angled shaft with smooth, flared tips. Flat, serrated, cross-actionhandle. Designed for folding and inserting of soft IOLs. Overalllength 105mm.

#3620

FAULKNER LENS HOLDING FORCEPS

Round, angled shafts with smooth tips for holding soft IOLS. Flat,serrated handle. Overall length 107mm.

#3621

KELMAN-MCPHERSON TYING FORCEPS

Angled shafts. Jaws feature 7.5mm platforms and smooth tips.Flat, serrated handle. Overall length 84mm.

#3547

KNOLLE-SHEPARD LENS HOLDING FORCEPS

Curved shafts with pegged, serrated jaws. Flat, serrated, fenes-trated, spring handle. Overall length 121mm.

#3039

KRATZ INTRAOCULAR LENS FORCEPS

Curved shafts with smooth tips. Flat, serrated, fenestrated,spring handle. Overall length 120mm.

#3034

LIVERNOIS FOLDING FORCEPS

Angled shafts with concave jaw surfaces. Standard, fenestratedhandle. Designed to pick up and fold IOL in one smooth motion.Overall length 111mm.

#3046

LIVERNOIS HOLDING FORCEPS

Highly polished, conical jaw surface. Standard, fenestrated handle.

#3047 Straight shafts. Overall length 102mm.#3048 Angled shafts. Overall length 100mm.

page 26




FORCEPS

OCUTEK LENS FOLDING FORCEPS � TITANIUM

Angled shafts with conical, paddled tips. Flat, serrated, fenestrat-ed handle. Made of high-grade, lightweight titanium.

#0131

PHACO LENS FOLDING FORCEPS

Designed for holding and folding of soft IOLs. Flat, serrated,spring handle. Overall length 125mm.

#3600

SHEETS-MCPHERSON TYING FORCEPS

Angled shafts. Jaws feature tying platforms with 1mm longcross-serrated tips. Flat, serrated handle. Overall length 86mm.

#3545

SHEPARD II LENS HOLDING FORCEPS

Curved shafts with notched tips. Flat, serrated, spring handlewith lock. Overall length 104mm.

#3526

SHEPARD LENS HOLDING FORCEPS

Curved shafts with duckbill tips. Lower tip is serrated. Flat, ser-rated spring handle. Overall length 117mm.

#3041 Locking handle.#3042 Standard handle

SIMCOE LENS FORCEPS

Straight shafts with one short, blunt and one long, pointed tip.Flat, smooth handle. Overall length 120mm.

#3038

SINSKEY LENS HOLDING FORCEPS

Angled shafts with smooth, delicate T-shaped, lower tip for 3-point fixation. Flat, serrated, fenestrated, spring handle. Overalllength 115mm.

#3044


page 27


FORCEPS

STEINERT IOL FORCEPS

Angled shafts with conically shaped jaws. Flat inside surfaces ofjaws. Standard, fenestrated handle. Designed for folding andinserting soft IOLs. Overall length 100mm.

#3049

THORNTON INTRAOCULAR LENS FORCEPS

Curved shafts with flat, smooth tips. Flat, smooth, cross-action,spring handle. Overall length 86mm.

#3043

BOTVIN IRIS FORCEPS

Angled shafts with angled tips. Flat, serrated handle. Overalllength 74mm.

#3171 1 x 2 teeth. #3172 Serrated tips.

BRACKEN CURVED IRIS FORCEPS

Curved shafts with cross-serrated tips. Flat, serrated handle.Overall length 100mm.

#3250

GILL CURVED IRIS FORCEPS

Curved shafts. Flat, serrated handle. Overall length 73mm.

#3190 1 x 2 teeth #3192 Cross-serrated tips.

GILLS-COLIBRI FORCEPS

Curved shafts with very delicate, angled, pointed tips. Smooth,fenestrated handle. Overall length 75mm.

#3173

page 28




FORCEPS

GRAEFE IRIS FORCEPS

Flat, serrated handle. Overall length 67mm.

#3150 Straight shafts. Tips feature 1 x 2 teeth.#3151 Curved shafts. Tips feature 1 x 2 teeth.#3154 Straight shafts with serrated tips.#3155 Curved shafts with serrated tips.

BONACCOLTO JEWELERS TYPE FORCEPS

Straight shafts with cross-serrated pointed tips. Wide, serratedhandle. Overall length 111mm.

#3730

JEWELERS FORCEPS #1

Straight shafts with fine pointed tips. Flat, smooth handle.Overall length 120mm.

#3251

JEWELERS FORCEPS #3

Straight shafts with extra fine pointed tips. Flat, smooth handle.Overall length 120mm.

#3732

JEWELERS FORCEPS #3C

Straight shafts with extra fine pointed tips. Flat, smooth handle.Overall length 110mm.

#3734

JEWELERS FORCEPS #4

Straight, tapered shafts with extra fine, pointed tips. Flat,smooth handle. Overall length 110mm.

#3736

JEWELERS FORCEPS #5

Straight, delicate tapered shafts with extra fine, pointed tips.Flat, smooth handle. Overall length 110mm.

#3738


page 29


FORCEPS

JEWELERS FORCEPS #5A

Angled shafts with pointed tips. Flat, smooth handle. Overalllength 107mm.

#3252

JEWELERS FORCEPS #7

Curved shafts with pointed tips. Flat, smooth handle. Overalllength 116mm.

#3740

HALSTEAD MOSQUITO FORCEPS

22mm, delicate, serrated jaws. Ring handle with ratchet lock.Overall length 124mm.

#4820 Straight jaws. #4821 Curved jaws.

HARTMAN MOSQUITO FORCEPS

20mm, delicate, serrated jaws. Ring handle with ratchet lock.Overall length 102mm.

#4810 Straight jaws.#4811 Curved jaws.

BERENS MUSCLE CLAMP

Adjustable, angled shaft. 13.5mm tips feature vertically oppos-ing tooth-in-hole configuration. 15mm vertical blade expansion.Round, knurled handle. Overall length 85mm.

#3690

BERKE PTOSIS FORCEPS

Curved shafts with longitudinally grooved jaws. Flat handle withlock. Overall length 102mm.

#3895 20mm jaws.#3896 27mm jaws.

page 30




FORCEPS

GUNDERSON MUSCLE FORCEPS

Angled shafts. 11mm tips feature longitudinal serrations. Flathandle with lock. Overall length 99mm.

#3680

JAMESON MUSCLE FORCEPS � ADULT

Angled shafts with 6 horizontally opposing, tooth-in-hole, 1mmteeth. Flat handle with lock. Overall length 100mm.

#3660 Shaft angled right. #3661 Shaft angled left.

JAMESON MUSCLE FORCEPS � PEDIATRIC

Angled shafts with 4 horizontally opposing, tooth-in-hole, 1mmteeth. Flat handle with lock. Locking handle. Overall length99mm.

#3670 Shaft angled right. #3671 Shaft angled left.

RIZZUTI SUPERIOR RECTUS FORCEPS

45° angled shafts. Curved tips feature 1 x 2 teeth. Flat, serrated,cross-action handle. Overall length 97mm.

#3654

TENNANT-TROUTMAN SUPERIOR RECTUS FORCEPS

45° angled shafts. Tips feature 1 x 2, 0.5mm teeth. Flat, serratedhandle. Overall length 107mm.

#3652

TROUTMAN SUPERIOR RECTUS FORCEPS

45° angled shafts. Tips feature 1 x 2, 0.9mm teeth. Flat, serratedhandle. Overall length 105mm.

#3650


page 31


FORCEPS

OCUTEK RETINAL FORCEPS � TITANIUM

20 gauge shaft. Round, knurled squeeze handle. Made of high-grade, lightweight titanium. Overall length 158mm.

#0280 Smooth, 1.0mm tips. Vertical action.#0281 Smooth, 3.5mm tips. Vertical action.#0282 Smooth, 2.0mm tips. Vertical action.#0283 Smooth, rounded, 2.5mm tips. Horizontal action.#0284 Smooth, rounded, 2.0mm tips. Horizontal action.#0285 2.5mm, cusp style jaws.#0286 2.0mm jaws with 0.7mm platforms.

BONN SUTURING FORCEPS


#3101

BONN SUTURING FORCEPS, LONG


#3157

page 32




FORCEPS

CASTROVIEJO SUTURING FORCEPS

Straight shafts with tyin g platforms. Tips feature 1 x 2 teeth.Standard, flat, serrated handle. Overall length 99mm.

#3257 0.9mm teeth. #3426 0.5mm teeth.

CASTROVIEJO SUTURING FORCEPS, ANGLED

Angled shafts with tying platforms. Tips feature 1 x 2 teeth.Overall length 100mm.

#3258 0.5mm teeth. Standard, flat, serrated handle.#3259 0.3mm teeth. Wide, flat, serrated handle.

CASTROVIEJO SUTURING FORCEPS � TITANIUM

Straight shafts with 6mm tying platforms. Tips feature 0.3mm, 1x 2 teeth. Flat, fenestrated, serrated handle. Made of high-grade,lightweight titanium. Overall length 115mm.

#0114

CASTROVIEJO SUTURING FORCEPS, WIDE HANDLE

Straight shafts with tying platforms. Tips feature 1 x 2 teeth.Wide, flat, serrated handle. Overall length 108mm.

#3158 1.5mm teeth. #3442 0.3mm teeth.#3440 0.12mm teeth. #3444 0.5mm teeth.#3446 0.9mm teeth.

FINE-CASTROVIEJO SUTURING FORCEPS

Straight shafts with tying platforms. Tips feature 1 x 2 teeth.Flat, serrated handle. Overall length 100mm.

#3420 0.12mm teeth. #3422 0.3mm teeth.

KELMAN-MCPHERSON CORNEAL/SUTURING FORCEPS

Angled shafts with tying platforms. Tips feature 1 x 2, 0.2mmteeth. Flat, serrated handle. Overall length 82mm.

#3204

MANHATTAN EYE & EAR SUTURING FORCEPS

Straight shafts with tying platforms. Tips feature 1 x 2, angledteeth. Wide, flat, serrated handle. Overall length 87mm.

#3400


page 33


FORCEPS

MCPHERSON CORNEAL/SUTURING FORCEPS

Shafts feature tying platforms. Tips feature 1 x 2, 0.2mm teeth.Flat, serrated handle. Overall length 84mm.


O�GAWA SUTURING FORCEPS � TITANIUM

Straight shafts with 6mm tying platforms. Tips feature 0.12mm, 1x 2 teeth. Round, knurled handle. Made of high-grade, light-weight titanium. Overall length 109mm.

#0115

SAUER SUTURING FORCEPS

Straight shafts. Tips feature 1 x 2, angled teeth. Wide, flat, ser-rated handle. Overall length 88mm.

#3402

STERN-CASTROVIEJO SUTURING FORCEPS


#3156

BISHOP-HARMON DRESSING FORCEPS

Straight shafts. Jaws feature cross-serrated tips. Fenestrated,easy to grip, flat handle. Overall length 86mm.

#3374

BISHOP-HARMON TISSUE FORCEPS

Jaws feature 1 x 2 teeth. Fenestrated, easy to grip, flat handle.Overall length 84mm.

#3370 Straight shafts. 0.3mm teeth.#3371 Curved shafts. Fine teeth#3372 Straight shafts. 0.8mm teeth.

page 34




FORCEPS

TISSUE FORCEP S, STANDARD

Straight shafts. Tips feature standard 1 x 2 teeth. Flat, serratedhandle. Overall length 100mm.

#3304

TISSUE FORCEPS, DELICATE

Tips feature delicate 1 x 2 teeth. Flat, serrated handle. Overalllength 100mm.


BABY JONES TOWEL CLAMP

Flat, serrated, cross-action handle. Overall length 60mm.

#3255

BACKHAUS TOWEL CLAMP

Ring handle with ratchet lock.

#3253 Overall length 90mm.#3254 Overall length 135mm.

DIEFFENBACK SERREFINE

Serrated jaw with cross-action handle.

#4800 Small. 10mm jaw. Overall length 38mm.#4802 Large. 16mm. Jaw. Overall length 48mm.

ANIS TYING FORCEPS

Extra delicate jaws with smooth tips. Round, knurled, cross-action handle. Overall length 114mm.

#3568 Straight jaws.#3570 Curved jaw.


page 35


FORCEPS

BECHERT-MCPHERSON TYING FORCEPS

Angled shafts with 10mm tying platforms and smooth tips. Flat,serrated handle. Overall length 83mm.

#3546

CASTROVIEJO TYING FORCEPS

Straight shafts with 6mm tying platforms and smooth tips.Wide, flat, serrated handle. Overall length 105mm.

#3560

FINE TYING FORCEPS

Curved shafts with typing platforms and smooth tips. Wide, flat,serrated handle. Overall length 103mm.

#3555

HARMS TYING FORCEPS

Jaws feature 7mm tying platforms with smooth tips. Flat, serrat-ed handle. Overall length 100mm.


HARMS-JAFFE TYING FORCEPS

Very delicate jaws feature tying platforms and smooth tips. Flat,fenestrated handle. Overall length 101mm.

#3552 Straight shafts. #3553 Curved shafts.

KELMAN-MCPHERSON TYING FORCEPS

Angled shafts with 7.5mm platforms and smooth tips. Flat, ser-rated handle. Overall length 84mm.

#3547

KELMAN MCPHERSON TYING FORCEPS � TITANIUM

45° angled shafts with 6mm tying platforms and smooth tips.Flat, serrated, fenestrated handle. Made of high-grade, light-weight titanium. Overall length 82mm.

#0118

page 36





page 37

FORCEPS

MCPHERSON TYING FORCEPS

Jaws feature 4mm tying platforms and smooth tips. Flat, serratedhandle. Overall length 85mm.

#3548 Straight shafts. #3549 Angled shafts.

OCUTEK TYING FORCEPS

Straight, heavy shafts with smooth tips. Wide, flat, serrated han-dle. Overall length 104mm.

#3562

SHEETS-MCPHERSON TYING FORCEPS

Angled shafts with typing platforms and 1mm long cross-serratedtips. Flat, serrated handle. Overall length 86mm.

#3545

SINSKEY TYING FORCEPS

Straight shafts. Very delicate jaws feature tying platforms andsmooth tips. Flat, serrated, cross-action handle. Overall length102mm.

#3566 Straight jaws. #3567 Curved jaws.

TENNANT TYING FORCEPS

Extra delicate jaws feature tying platforms and smooth tips.Round knurled handle. Overall length 102mm.

#3556 Straight shafts. #3557 Curved shafts.

GASKIN FRAGMENT FORCEPS

Angled shaft. Very delicate, 11mm jaws feature tying platformsand smooth tips. Flat, serrated handle. Overall length 103mm.

#3542


FORCEPS

ALABAMA UNIVERSITY UTILITY FORCEPS

Straight shafts. Tips feature 15mm long, grooved platforms. Flat,serrated handle. Overall length 94mm.

#3582

BONACCOLTO UTILITY FORCEPS

Straight shafts. Longitudinally serrated jaws with cross serratedtips. Wide, flat, serrated handle. Overall length 114mm.

#3577 1.2mm wide platforms.#3578 1.7mm wide platforms.

MCCULLOUGH UTILITY FORCEPS

Straight shafts with 15mm by 1.5mm jaw. Flat, serrated handle.Overall length 98mm.

#3580 Cross serrated jaws.#3581 Smooth jaws.

NUGENT UTILITY FORCEPS

Angled shat with 10mm long jaws. Flat, serrated handle. Overalllength 113mm.

#3572 Smooth jaws.#3573 Cross serrated jaws.

WILLS HOSPITAL UTILITY FORCEPS

Straight shafts. Tips feature 15mm platform with finely criss-crossed serrations. Flat, serrated handle. Overall length 111mm.

#3571

BROWN NUCLEUS CRACKER � TITANIUM

Straight shafts with 1.5mm x 1.2mm paddle style tips. Flat, fen-estrated, cross-action handle. Made of high-grade, lightweighttitanium. Overall length 95mm.

#0130

page 38




FORCEPS

DODOCK NUCLEUS CRACKER

Curved shafts with paddled tips. Wide, flat, serrated, cross-action handle. Overall length 110mm.

#3596

MACGREGOR CONJUNCTIVA FORCEPS

Straight shafts. Jaws feature 6mm, serrated platforms. Wide,flat, serrated handle. Overall length 110mm.

#3460

MCDERMOTT NUCLEUS CRACKER

Curved shafts with paddled tips. Wide, flat, serrated, cross-action handle. Overall length 108mm.

#3597

SALZ NUCLEUS CRACKER

Curved shafts with paddled tips. Colibri-style cross-action han-dle. Overall length 74mm.

#3595

THORNTON INCISION SPREADER

Straight shafts. Jaws feature 0.1mm tapered sandblasted tips.Stop prevents overspreading of incision. Flat, serrated handle.Overall length 107mm.

#3045

HOOKS

BURCH FIXATION HOOK

Straight shaft with two-pronged tip. Flat, smooth handle. Overalllength 111mm.

#7635

OCUTEK DOUBLE FIXATION HOOK

Straight shaft with sharp, two-pronged hook. Flat, serrated han-dle.

#7620 Small, 2mm x 1.5mm hook. Length 124mm.#7622 Large, 2.5mm x 2mm hook. Length 129mm.


page 39


HOOKS

SCLERAL TWIST FIXATION CONE

Straight shaft with 2.5mm diameter fixation cone. Round,knurled handle. Overall length 116. Complete with tip protector.

#1778

TWIST FIXATION HOOK

Straight shaft with 0.8mm twist hook. Round, knurled handle.Overall length 110mm.

#7640 Right twist. #7641 Left twist.

BOAT HOOK LENS MANIPULATING HOOK

Straight shaft with dual �Y�-shaped and curved tip. Round,knurled handle. Overall length 111mm.

#7023

CLAYMAN-JAFFE LENS MANIPULATING HOOK

Angled shaft with angled, 0.9mm, blunt tip. Round, knurled han-dle. Overall length 117mm.

#7021

FENZL INSERTION HOOK

0.2mm �T�-shaped tip. Round knurled handle. Overall length120mm.

#7606 Straight shaft. #7607 Angled shaft.

HARRIS-SINSKEY LENS MANIPULATING HOOK

Angled shaft with angled, blunt tip. Flat, smooth handle. Overalllength 113mm.

#7623

JAFFE LENS MANIPULATING HOOK

Straight shaft with angled, 0.15mm, blunt tip. Flat, smooth han-dle. Overall length 115mm.

#7020

JAFFE-MALTZMAN LENS MANIPULATING HOOK

Angled shaft with 0.15mm �V�-shaped tip. Flat, smooth handle.Overall length 120mm.

#7026

page 40




HOOKS

KUGLEN IRIS HOOK AND LENS MANIPULATOR

Push-pull design. Shaft features teardrop-shaped tip.

#7007 Straight shaft. Round, knurled handle. Overall length 111mm.

#7008 Angled shaft. Round, knurled handle. Overall length 110mm.

#7602 Straight shaft. Flat, smooth handle. Overall length 116mm.

#7604 Angled shaft. Flat, smooth handle. Overall length 118mm.

KUGLEN IRIS HOOK LENS MANIPULATOR

Cloverleaf Tip, Straight shaft with cloverleaf tip. Flat, smoothhandle. Overall length 120mm.

#7603

LEWICKY LENS MANIPULATING HOOK

Curved shaft with angled, blunt tip. Flat, smooth handle. Overalllength 115mm.

#7014

MALTZMAN-FENZL LENS MANIPULATING HOOK

.15mm, �V�-shaped tip. Round, knurled handle. Overall length117mm.

#7024 Straight shaft #7025 Angled shaft.

OSHER �Y� HOOK

Straight shaft with �Y�-shaped tip. Round, knurled handle.Overall length 120mm.

#7022


page 41


HOOKS

SINSKEY HOOK II

0.2mm, angled tip. Round, knurled handle.

#7005 Straight shaft. Overall length 110mm.#7006 Angled shaft. Overall length 117mm.

SINSKEY HOOK � TITANIUM

Angled shaft with angled tip. Round, knurled handle. Made ofhigh-grade, lightweight titanium. Overall length 118mm.

#0538

SINSKEY IRIS AND IOL HOOK

Straight shaft with 0.2mm angled tip. Flat, smooth handle.Overall length 117mm.

#7616

SINSKEY MODIFIED HOOK

Curved shaft with 0.2mm hook. Flat, serrated handle. Overalllength 121mm.

#7616M

BONN IRIS HOOK

Straight shaft with blunt hook. Flat, smooth handle. Overalllength 123mm.

#7613

BONN IRIS HOOK, ROUND HANDLE

Straight shaft with blunt hook. Overall length 123mm.

#7626

HIRSCHMAN IRIS �H� HOOK

Angled shaft with �H� shaped hook. Round, serrated handle.Overall length 124mm.

#7027

page 42

Ophthalmic Instrument CatalogOphthalmic Instrument Catalog


HOOKS

HIRSCHMAN IRIS HOOK

Angled shaft with blunt hook. Round, knurled handle. Overalllength 111mm.

#7617

JAFFE IRIS HOOK

Straight shaft with blunt, 1.5mm hook. Flat, serrated handle.Overall length 120mm.

#7612

JAFFE-KNOLLE IRIS HOOK

Angled shaft with small, blunt hook. Round, knurled handle.Overall length 115mm.

#7605

KNOLLE IRIS HOOK

Straight shaft with small blunt hook. Round, knurled handle.Complete with tip protector. Overall length 119mm.

#7002

RAININ IRIS HOOK

Straight shaft with blunt hook. Round, knurled handle. Overalllength 127mm.

#7001

SHEETS IRIS HOOK

Straight shaft with inverted, sharp hook. Round, knurled handle.Overall length 124mm. Complete with tip guard.

#7600

SHEPARD IRIS HOOK

Straight shaft with small blunt hook. Flat, smooth handle.Overall length 124mm.

#7614

TYRELL IRIS HOOK

Straight shaft with sharp, 1.5mm hook. Flat, serrated handle.Overall length 121mm.

#7610


page 43


HOOKS

GRAEFE MUSCLE HOOK

Straight shaft with hook. Flat, serrated handle. Overall length144mm.

#7501 Size #1. 7mm x 1mm hook.#7502 Size #2. 9mm x 1.5mm hook.#7503 Size #3. 10mm x 1.5mm hook.

GREEN MUSCLE HOOK

Curved shaft with 10mm x 2mm tapered hook. Flat, smoothhandle. Overall length 128mm.

#7512

JAMESON MUSCLE HOOK

Curved shaft with bulbous tipped hook. Flat, smooth handle.

#7509 Small, 9mm x 1.3mm hook. Overall length 124mm.

#7510 Large, 10mm x 1.3mm hook. Overall length 130mm.

STEVENS TENOTOMY HOOK

Straight shaft with 5mm x 1mm hook. Flat, smooth handle.Overall length 117mm.

#7520

KNIVES, CYSTOTOMES, DISSECTORS

BARD-PARKER BLADE HANDLE

Overall length 117mm.

#1295 No. 3.#1299 No. 9.

BARKAN GONIOTOMY KNIFE

Straight shaft with 2mm blade. Flat, smooth handle. Overalllength 117mm.

#1165

page 44





DISPOSABLE BLADES

Single use blades. Packaged sterile. 12 blades/package.

#1296 No. 11 blade.

ELLIS FOREIGN BODY SPUD

Lightly curved blade with thin, rounded tip. Flat, smooth handle.Overall length 103mm.

#1476

FRANCIS FOREIGN BODY SPUD

Straight shaft with angled, flag-shaped tip. Flat, smooth handle.Overall length 106mm.

#1475

GILL CORNEAL KNIFE

3.5mm, spoon-shaped blade. Flat, serrated handle. Overalllength 121mm.

#1380 Straight blade. #1381 Curved blade.

GIRARD-SWAN KNIFE NEEDLE

Straight blade. Round, knurled handle. Overall length 108mm.

#1170

GOLF CLUB SPUD

Straight shaft with angled tip. Flat, serrated handle. Overalllength 117mm.

#1474


page 45



MVR STILETTO BLADE

Straight 19 gauge shaft with lancet shaped tip. Round, serrated,chuck handle. Overall length 130mm.

#1175 Chuck handle.#1176 Blade

OPHTHO-BURR SYSTEM

Battery powered handpiece used with 1.0mm, 2.5mm or 5.0mmburs. Designed to aid in the removal of corneal foreign bodiesand corneal rust rings.

#85-50810 1.0mm bur, single use, sterile. Box of 10.#85-50815 Handpiece only.#85-50820 Complete system. Includes one handpiece (85-50815) and one box of ten 1.0mm burs (85-50810).#85-50850 2.5mm diamond bur, reusable.#85-50860 5.0mm diamond bur, reusable.

PAUFIQUE GRAFT KNIFE

Straight shaft with angled, 1.5mm x 3.0mm angled tip. Flat,smooth handle. Overall length 105mm.

#1150

page 46





SPUD AND GOUGE

Double-ended with removable 18mm x 1.25mm gouge tip and4mm x 2mm spud tip. Round, knurled handle. Overall length105mm.

#1485

SWAN KNIFE NEEDLE

Straight, 5mm x 0.3mm blade. Flat, smooth handle. Overalllength 114mm.

#1160

TOOKE CORNEAL KNIFE

Straight, 2mm x 16mm blade. Flat, serrated handle. Overalllength 114mm.

#1360

WHEELER DISCISSION KNIFE

Straight, 1mm x 16mm blade. Flat, smooth handle. Overall length116mm.

#1190

ZIEGLER KNIFE NEEDLE

Straight, sickle-shaped blade. Flat, serrated handle. Overalllength 117mm.

#1153 3mm blade.#1155 5mm blade.

LENS LOOPS AND SPOONS

ANIS IRRIGATING VECTUS

23 gauge cannulated shaft with heart-shaped loop. Loop featuretwo front ports. Shaft length 36mm.

#6455

CULLER LENS SPOON

Straight shaft with spoon. Flat, smooth handle. Overall length133mm.

#7425


page 47



DREW-KNOLLE REVERSE IRRIGATING VECTUS

23 gauge, cannulated shaft with 6mm x 8mm loop. Three irrigat-ing ports at 12, 10 and 2 o�clock. Shaft length 38mm.

#6450

GILLS-WELSH LENS LOOP

Double-ended with 5mm x 7mm loop on one end and a very thinolive tip on the opposite end. Flat, serrated handle. Overalllength 114mm.

#7405

HOFFMAN IRRIGATING VECTUS

Curved, 16 gauge, cannulated shaft with 4mm x 17mm, curvedserrated loop. Three irrigating ports at 12, 3 and 9 o�clock. Shaftlength 38mm.

#6460

KIRBY EXPRESSOR HOOK AND LOOP

Double-ended. 5mm x 10mm loop on one end with a 10mm widemuscle expressor hook on the other end. Round, knurled handle.Overall length 149mm.

#7403

KIRBY LENS LOOP

5mm x 10mm loop. Round, knurled handle. Overall length 135mm.

#7402

KNOLLE-PEARCE IRRIGATING VECTUS

23 gauge cannulated shaft with lens loop. Loop features threeirrigating ports at the 12, 10 and 2 o�clock position. Shaft length38mm.

#6420

LEWIS LENS LOOP

Flat, smooth handle. Overall length 137mm.

#7400 Small loop.#7401 Large loop.

NEW ORLEANS LENS LOOP

10mm x 4mm loop. Flat, smooth handle. Overall length 131mm.

#7410

page 48





SHEETS IRRIGATING VECTUS

21 gauge cannulated shaft with 6mm x 8mm serrated loop. Threeirrigating ports at 12, 9 and 3 o�clock. Shaft length 38mm.

#6441

SIMCOE IRRIGATING LENS LOOP

25 gauge cannulated shaft with strongly curved, finely serratedloop. Loop features two irrigating ports.

#6458 Right. #6459 Left.

SIMCOE LENS LOOP

Double-edged. Elongated loops, left and right, with fine serra-tions. Round knurled handle. Overall length 138mm.

#7119

WILDER LENS LOOP

Serrated, 5mm X 10mm loop. Flat, smooth handle. Overall length133mm.

#7412

NEEDLE HOLDERS

ANIS NEEDLE HOLDER

Extra delicate, 10mm, smooth jaws. Round, knurled handle.Overall length 114mm.

#4180 Straight jaws. #4181 Straight jaws. Locking handle.#4182 Curved jaws.#4183 Curved jaws. Locking handle

BARRAQUER NEEDLE HOLDER

Extra delicate, 9mm, smooth jaws. Round knurled handle. Overalllength 124mm.

#4164 Straight jaws. #4165 Straight jaws. Locking handle.#4166 Curved jaws.#4167 Curved jaws. Locking handle.

BARRAQUER NEEDLE HOLDER � LARGE HANDLE

Fine, 9mm, smooth jaws. Large, round, knurled handle. Overalllength 132mm.

#4168 Curved jaws.#4169 Curved jaws. Locking handle


page 49


NEEDLE HOLDERS

BARRAQUE R NEEDLE HOLDER � TAPERED JAW

Extra delicate, 9mm, smooth, tapered jaws. Round, knurled han-dle. Overall length 134mm.

#4210 Curved jaws. Locking handle. #4211 Curved jaws. #4220 Straight jaws. Locking handle. #4221 Straight jaws.

BARRAQUER NEEDLE HOLDER � TITANIUM

9mm, delicate, curved jaws. Round, knurled handle with hingespring. Made of high-grade, lightweight titanium. Overall length110mm.

#0392 Locking handle. #0393 Standard handle.

CASTROVIEJO NEEDLE HOLDER � DELICATE

Delicate, 9mm, smooth jaws. Flat, serrated handle. Overalllength 140mm.

#4120 Curved jaw. Locking handle.#4121 Straight jaw.#4130 Straight Jaw. Locking handle.#4131 Curved jaw.

CASTROVIEJO NEEDLE HOLDER � STANDARD

Standard, 11mm, smooth jaws. Flat, serrated handle with lock.Overall length 140mm.

#4140 Straight jaw. #4141 Curved jaw.

CASTROVIEJO NEEDLE HOLDER � WIDE HANDLE

Delicate, 9mm, smooth jaws. Wide, flat, serrated handle. Overalllength 126mm.

#4154 Straight jaw. Locking handle.#4155 Straight jaw.#4156 Curved jaw. Locking handle.#4157 Curved jaw.

COHAN NEEDLE HOLDER

Extra delicate, 8mm, curved jaws. Round, knurled handle. Overalllength 115mm.

#4236 Standard handle. #4238 Locking handle.

page 50




NEEDLE HOLDERS

DERF NEEDLE HOLDER

Straight, serrated jaws. Ring handle with ratchet lock. Overalllength 130mm.

#4270

KALT NEEDLE HOLDER

Straight, cross-serrated jaws. Flat, serrated handle. Overalllength 136mm.

#4100 Delicate, 9mm jaws.#4102 Standard, 11mm jaws.

MCINTYRE FISH HOOK NEEDLE HOLDER

Straight, 3mm jaws. Round, serrated handle with lock. Overalllength 125mm.

#4250

MCPHERSON NEEDLE HOLDER

Extra delicate, 9mm, smooth, tapered jaws. Flat, serrated handle.Overall length 103mm.

#4173 Straight jaws. Locking handle#4174 Straight jaws.#4175 Curved jaws. Locking handle#4176 Curved jaws.

OCUTEK MICROPOINT NEEDLE HOLDER

Extra delicate, 7mm, smooth jaws. Round, knurled handle.Overall length 120mm.

#4240 Straight jaws.#4241 Curved jaws.#4242 Straight jaws. Locking handle.#4243 Curved jaws. Locking handle.

OCUTEK NEEDLE HOLDER � TITANIUM

7mm, delicate, curved jaws. Round, knurled handle. Made ofhigh-grade, lightweight titanium. Overall length 107mm.

#0390 Standard handle. #0391 Locking handle.


page 51


Medtronic Ophthalmic Instrument Catalog page 52


NEEDLE HOLDERS

TROUTMAN NEEDLE HOLDER

Very delicate, gently curved, 9mm jaws. Round, serrated handle.Overall length 121mm.

#4184 Curved jaws.#4185 Curved jaws. Locking handle.

TROUTMAN-BARRAQUER NEEDLE HOLDER

Extra delicate, 6mm, curved, smooth jaws. Round, knurled han-dle. Overall length 114mm.

#4161

WEBSTER NEEDLE HOLDER

Straight, smooth jaws. Ring handle with ratchet lock. Overalllength 125mm.

#4274

NUCLEUS MANIPULATORS /DIVIDERS

BECHERT NUCLEUS ROTATOR

Angled shaft with �Y�-shaped tip. Round, knurled handle.Overall length 122mm.

#7645

CLAYMAN NUCLEUS ROTATOR

Angled shaft with 0.5mm, �V�-notched tip. Round, knurled han-dle. Overall length 122mm.

#7648

JAFFE-BECHERT NUCLEUS ROTATOR

Angled shaft with �Y�-shaped tip. Round, knurled handle.Overall length 115mm.

#7646


NUCLEUS MANIPULATORS /DIVIDERS

KANSAS NUCLEUS BISECTOR

Angled, semi-sharp blade. Round, knurled handle. Overall length115mm.

#7662

KANSAS NUCLEUS SUPPORT SPATULA

Straight shaft with curved, 3mm wide spatula blade. Flat, smoothhandle. Overall length 123mm.

#7660 Right handed use. #7661 Left handed use.

KANSAS NUCLEUS TRISECTOR

Three sided resector set on offset shaft. Round, knurled handle.Overall length 110mm. Designed to divide nucleus into three sec-tions for removal during manual, small incision surgery.

#7663 Left handed use. #7664 Right handed use.

KOCH STOP AND CHOP MANIPULATOR

Angled shaft with 1.5mm, angled tip. Round, knurled handle.Overall length 112mm.

#7654

LESTER IOL MANIPULATOR

Hour glass-shaped tip. Round, knurled handle.

#7624 Straight shaft. Overall length 118mm.#7625 Angled shaft. Overall length 117mm.

MINAMI �M� HOOK

Multi-angled shaft with teardrop-shaped tip. Round, knurled han-dle. Overall length 117mm.

#7655

NAGAHARA NUCLEUS CHOPPER

Angled shaft with 60° offset blade and 1.25mm tip. Round,knurled handle. Overall length 103mm.

#7651 Left. #7652 Right.



page 53

NUCLEUS MANIPULATORS/DIVIDERS

NICHAMIN NUCLEUS CHOPPER AND SPATULA

Double-ended. Angled, wedge-shaped chopper with rounded tipon one end with 0.5mm angled spatula blade on the oppositeend. Round, knurled handle. Overall length 140mm.

#7653

OCUTEK NUCLEUS DIVIDER � TITANIUM

Angled shaft with angled, cutting tip. Round, knurled handle.Made of high-grade, lightweight titanium. Overall length124mm.

#0539

ROSEN PHACO SPLITTER

Angled shaft with blunt, wedge shaped, inferior edge tip. Round,knurled handle. Overall length 115mm.

#7656 Standard model.#7657 60° angled tip.

PROBES AND DIALATORS

BODIAN MINI-LACRIMAL PROBES

Set consists of two 1mm diameter, 37mm long, gently curved,blunt probes with 300mm of silicone tubing fastened to eachprobe. Overall length 370mm.

#6188

BOWMAN STAINLESS STEEL LACRIMAL PROBES

Double-ended, malleable, stainless steel probes.

#6170 Size 0000/000. #6171 Size 00/0.#6172 Size1/2. #6173 Size 3/4.#6174 Size 5/6.#6175 Size 7/8.

BOWMAN STERLING SILVER LACRIMAL PROBES

Double-ended, malleable, sterling silver probes.

#6160 Size 0000/000. #6161 Size 00/0.#6162 Size 1/2. #6163 Size 3/4.#6164 Size 5/6.#6165 Size 7/8.

page 54


Obsolete



Obsolete

Obsolete


page 55


CASTROVIEJO LACRIMAL DILATOR

Double-ended with small and medium tapers. Round, knurledhandle. Overall length 138mm.

#6120

CATALANO LACRIMAL INTUBATION SET

Set consists of two 0.7mm diameter, 140mm long, malleablesterling silver, blunt probes with 290mm of silicone tubing fas-tened to each probe. Overall length 570mm.

#6187

HARMS TRABECULOTOMY PROBE

Double-pronged probe with 9mm prongs set at a 90° angle.Round, knurled handle. Overall length 46mm.

#6208 Right. #6209 Left.

INFANT LACRIMAL DILATOR

Delicate taper. Round, knurled handle. Overall length 78mm.

#6110

JACKSON LACRIMAL INTUBATION SET

Set consists of two 20 gauge, 155mm long, malleable stainlesssteel, blunt probes with 300mm of silicone tubing fastened toeach probe. Overall length 610mm.

#6186



MULDOON LACRIMAL DILATOR

Medium, 27mm taper with straight guide at tip. Round, knurledhandle. Overall length 99mm.

#6134

PIGTAIL PROBE TUBING

Pre-cut and formed in 320mm lengths. 4 tubes/package.

#6204

QUICKERT PROBES

Double ended, one end features a Jones taper point while theother a regular Bowman point. Malleable sterling silver. Overalllength 142mm.

#6190 Size 00. #6191 Size 0.#6192 Size 1. #6193 Size 2.#6194 Size 3. #6195 Size 4.

RUEDEMANN LACRIMAL DILATOR

Short 12mm taper with needle-type tip. Round, knurled handle.Overall length 71mm.

#6136

WILDER LACRIMAL DILATOR

Tapered shaft. Round, knurled handle.

#6101 Size 1, fine taper. Overall length 110mm.#6102 Size 2, medium taper. Overall length 110mm.#6103 Size 3, heavy taper. Overall length 110mm.

WORST PIGTAIL PROBE

Double-ended, 0.8mm diameter curved blunt probes. Round,knurled handle. Overall length 149mm.

#6200 Standard pattern. #6202 With eye holes.

page 56




RETINA PICKS, HOOKS, SPATULAS

ECHART RETINAL HOOK

Straight, 44mm long, 20 gauge shaft with 0.5mm, 45° angled tip.Round, knurled handle. Length 136mm.

#8102

FOERESTER RETINAL PICK

Straight shaft with 1mm, 55° angled tip. Round, knurled handle.Overall length 123mm.

#8107

GASS RETINAL DETACHMENT HOOK

Straight shaft with flattened 13mm, fenestrated, hook. Flat,smooth handle. Overall length 118mm.

#8103

LAGUA RETINAL PICK

Straight, 34mm long, 20 gauge shaft with rounded tip. 2mm ver-tical notch in tip. Round knurled handle. Overall length 127mm.

#8101

MEMBRANE RAKE SPATULA

Straight, 20 gauge shaft with rake tip spatula blade. Round,knurled handle.

#8002 Delicate. Overall length 115mm.#8003 Standard. Overall length 130mm.

MEMBRANE SPATULA

Straight, 20 gauge shaft with rounded tip spatula blade. Round,knurled handle. Overall length 130mm.

#8001

OCUTEK ANGLED RETINAL PICK

Straight shaft with 0.5mm, angled tip. Round, knurled handle.Overall length 125mm.

#8104 110° tip angle. #8105 130° tip angle.#8106 150° tip angle.

OCUTEK ANGLED RETINAL SPATULA

Straight shaft with triangular, 0.5mm tip. 4mm flat surface cutinto shaft. Round, knurled handle. Overall length 124mm.

#8004 110° tip angle. #8005 130° tip angle.#8006 150° tip angle.


page 57


RETRACTORS

GRAETHER COLLAR BUTTON

23 gauge, cannulated shaft with side port. Designed for irisretraction and lens manipulation. Roughened posterior surfacemay be used to polish capsule.

#6447 Straight shaft. Shaft length 25mm.#6448 45° angled shaft. Shaft length 23mm.

GRAETHER COLLAR BUTTON ON HANDLE

Round, knurled handle. Overall length 120mm. Designed for irisretraction and lens manipulation. Roughened posterior surfacemay be used to polish capsule.

#7000 Straight shaft. #7001 Angled shaft.

MACKOOL CAPSULE RETRACTOR

1mm hook suspended 0.5mm from distal tip on angled shaft.Round, knurled handle. Overall length 120mm. Ideal for retract-ing anterior capsule flap while guiding superior IOL loop insidebag.

#7016

RIZZUTI EXPRESSOR AND IRIS RETRACTOR

Double ended muscle hook/lens expressor. 2mm wide retractorblade. Round, knurled handle. Overall length 143mm.

#7650

KNAPP LACRIMAL SAC RETRACTOR

Blunt, 5mm long by 8mm wide, four-prong tip Overall length138mm.

#5600

STEVENSON LACRIMAL SAC RETRACTOR

3 x 3, 2mm, curved teeth. Blade spread 20mm. Overall length80mm.

#5550

page 58





page 59

RETRACTORS

CONWAY LID RETRACTOR

Straight shaft with curved, 8mm wide retractor blade. Flat,smooth handle. Overall length 135mm.

#5510

DESMARRES LID RETRACTOR

Straight shaft with curved retractor blade. Flat, smooth handle.

#5500 Size 0. 11mm wide blade. Overall length 140mm.#5501 Size 1. 13mm wide blade. Overall length 140mm.#5502 Size 2. 15mm wide blade. Overall length 140mm.#5503 Size 3. 17mm wide blade. Overall length 143mm.

JAEGER LID PLATE

Autoclavable plastic. Overall length 99mm.

#5700

JAFFE LID RETRACTORS

One pair of 15mm wide, curved, retractor blades. Overall length42mm.

#5108

ARRUGA ORBITAL RETRACTOR

10mm by 18mm cupped retractor blade. Overall length 145mm.

#5520

OCUTEK ORBITAL RETRACTOR

Double ended, thin, �S�-curved, ribbon retractor. Overall length180mm.

#5526 10mm and 14mm wide blades.#5527 16mm and 25mm wide blades.

SCHEPENS ORBITAL RETRACTOR

Smooth, 14mm by 56mm blade with 4.5mm notch in blade.Overall length 148mm.

#5522



RINGS

FLIERINGA FIXATION RING

Stainless steel fixation ring.

#8212 12mm diameter. #8213 13mm diameter.#8214 14mm diameter. #8215 15mm diameter.#8216 16mm diameter. #8217 17mm diameter.#8218 18mm diameter. #8219 19mm diameter.#8220 20mm diameter. #8221 21mm diameter.#8222 22mm diameter.

MCNEIL-GOLDMAN SCLERAL AND BLEPHAROSTAT RING

Fixation ring with loops to retract lids.

#8226 Pediatric size. #8228 Adult size.

THORNTON FIXATION RING

16mm ring with teeth designed for globe fixation. Round, knurledhandle.

#1777

FINE-THORNTON FIXATION RING � TITANIUM

3 / 4, 16mm diameter ring with 9 point fixation. Round, knurledhandle. Made of high-grade, lightweight titanium. Overall length127mm.

#0502

FINE-THORNTON SWIVEL FIXATION RING

Swiveling, open-ended ring with teeth designed for globe fixa-tion. Flat, smooth handle. Overall length 115mm.

#8230 13mm diameter for clear cornea.#8231 16mm diameter for scleral tunnel.

OCUTEK GLOBE FIXATION RING

16mm diameter, open-ended globe fixation ring with concentricgrooves for clear cornea phaco incisions and IOL insertion.Round, knurled handle. Overall length 98mm.

#8233




page 61

SISSORS

GILLS-VANNAS CAPSULOTOMY SCISSORS

Extra thin, 8mm blades with pointed tips. Flat, serrated, springhandle. Overall length 83mm.

#2424 Straight. #2425 Curved.

GILLS-VANNAS CAPSULOTOMY SCISSORS � ANGLED

Extra thin, 7mm, angled forward blades with pointed tips. Flat,serrated, spring handle. Overall length 80mm.

#2426

GILLS-WELSH CAPSULOTOMY SCISSORS

Angled forward blades with pointed tips. Flat, serrated, springhandle.

#2427 5mm blades. Overall length 80mm.#2428 11mm blades. Overall length 86mm.

HOFFER-STERN CAPSULE SCISSORS

Extra thin, 10mm, convexly curved, angled forward blades withpoint tips. Flat, serrated, spring handle. Overall length 105mm.

#2406

OCUTEK CAPSULOTOMY SCISSORS

Extra thin, 10mm, straight, angled forward blades with pointedtips. Flat, fenestrated, spring handle. Overall length 110mm.

#2404

STERN-GILLS CAPSULOTOMY SCISSORS

10mm, angled forward blades with pointed tips. Flat, serrated,spring handle. Overall length 109mm.

#2421

URIBE-STERN CAPSULE SCISSORS

Extra thin, 10mm, concavely curved, angled forward blades withpointed tips. Flat, serrated spring handle. Overall length 100mm.

#2405

VANNAS CAPSULOTOMY SCISSORS

8.75mm blades with pointed tips. Flat, serrated, spring handle.Overall length 84mm.

#2400 Straight. #2401 Curved.


SISSORS

VANNAS CAPSULOTOMY SCISSORS, ANGLED

6mm blades with pointed tips. Flat, serrated spring handle.Overall length 82mm.

#2410 Angled forward. #2420 Angled to side.

AZAR CALIBRATED CORNEAL SCISSORS

Curved, medium blades with 1mm to 6mm calibrations. Flat, ser-rated, spring handle. Overall length 108mm.

#2135

CASTROVIEJO CORNEAL SCISSORS

13mm curved blades. Flat, serrated, spring handle. Overalllength 111mm.

#2124 Right. #2125 Left.

CASTROVIEJO CORNEAL SCISSORS � TITANIUM

5mm, curved blades with blunt tips. Flat, fenestrated, springhandle. Overall length 95mm.

#0401 Right. #0402 Left.

CASTROVIEJO KERATOPLASTY SCISSORS

Side angled blades with blunt tips. Flat, serrated, spring handle.

#2142 Small blades. Overall length 107mm.#2145 Medium blades. Overall length 100mm.

CASTROVIEJO KERATOPLASTY SCISSORS, WIDE HANDLE

12mm, curved blades with blunt tips. Wide, flat, serrated handle.Overall length 125mm.

#2134

page 62





page 63

SISSORS

CASTROVIEJO MICRO CORNEAL SCISSORS

Curved, blunt blades. Flat, serrated, spring handle. Overall length105mm.

#2130 11.5mm blades. #2131 9mm blades.

CASTROVIEJO MINI CORNEAL SCISSORS � TITANIUM

Curved, 6mm blades. Flat, fenestrated, spring handle. Made ofhigh-grade, lightweight titanium. Overall length 116mm.

#0403

CASTROVIEJO STANDARD CORNEAL SCISSORS

15.8mm, curved, blunt blades. Flat serrated, spring handle.Overall length 111mm.

#2120

KATZIN MINI CORNEAL TRANSPLANT SCISSORS

Miniature curved blades. Lower blade longer than upper blade.Flat, serrated spring handle. Overall length 103mm.

#2270 Curved right. #2271 Curved left.

ORNEAL TRANSPLANT SCISSORS

6mm, strongly curved blades. Flat, serrated, spring handle withstop. Overall length 100mm.


AEBLI CORNEAL SECTION SCISSORS

Angled blades with blunt tips. Flat, serrated handle. Overalllength 115mm

#2296 Right. #2297 Left.

BARRAQUER MICRO CORNEAL SECTION SCISSORS

Small, forward angled blades with pointed tips. Flat, serrated,spring handle with stop. Overall length 102mm.

#2106 Right. #2107 Left.


SISSORS

CASTROVIEJO MEDIUM CORNEAL SECTION SCISSORS

Angled blades with blunt tips. 10.5mm lower blade with 10mmupper blade. Flat, serrated, spring handle. Overall length 105mm.

#2110 Right. #2111 Left.

CASTROVIEJO MEDIUM CORNEAL SECTION SCISSORS

Wide HandleAngled blades with blunt tips. 10mm lower blade with 9.5mmupper blade. Wide, flat, serrated handle. Overall length 126mm.

#2114 Right. #2115 Left.

CASTROVIEJO MICRO CORNEAL SECTION SCISSORS

7mm, angled blades with blunt tips. Flat, serrated spring handle.Overall length 101mm.

#2112 Right. #2113 Left.

CASTROVIEJO MINI CORNEAL SECTION SCISSORS

12mm, angled blades with blunt tips. Flat, serrated, spring handle.Overall length 106mm.

#2108 Right. #2109 Left.

CASTROVIEJO STANDARD CORNEAL SECTION SCISSORS

Angled blades with blunt tips. 13.5mm lower blade w/13mmupper blade. Flat, serrated , spring handle. 110mm.

#2100 Right. #2101 Left.

MCPHERSON-CASTROVIEJO CORNEAL SECTIONSCISSORS

Angled blades with blunt tips. 12mm lower blade with 11.6mmupper blade. Flat, serrated, spring handle. Overall length 93mm.

#2104 Right. #2105 Left.

TROUTMAN MINI CORNEAL SECTION SCISSORS

10mm, side-angled, curved blades with blunt tips. Flat, serratedhandle with stop. Overall length 106mm.


TROUTMAN-CASTROVIEJO MICRO CORNEAL

Section Scissors7mm, angled blades with blunt tips. Flat, serrated handle withstop. Overall length 101mm.

#2252 Right. #2253 Left.

page 64




SISSORS

TROUTMAN-CASTROVIEJO MICRO CORNEAL

Section Scissors10mm, angled blades with blunt tips. Flat, serrated handle withstop. Overall length 106mm.

#2250 Right. #2251 Left.

ENUCLEATION SCISSORS

Curved blades with blunt tips. Ring handle. Overall length133mm.

#2801 Medium curve. #2801 Strong curve.

INTRAOCULAR SCISSORS

2mm pointed blades. Squeeze handle. Provided with protectivecap. Overall length 146mm.

#2430 Straight blades. #2431 Curved blades.

WILSON INTRAOCULAR SCISSORS

Straight, 18 gauge diameter shaft featuring straight, 2mm bladeswith blunt tips. Squeeze handle. Overall length 90mm.

#2435

BARRAQUER IRIS SCISSORS

Angled blade with blunt tips. Squeeze handle.

#2320 7mm blade. Overall length 54mm.#2322 10mm blade. Overall length 55mm.

DEWECKER IRIS SCISSORS

8mm, angled blades. Flat, serrated, squeeze handle. Overalllength 111mm.

#2323

IRIS SCISSORS

16mm blades with pointed tips. Flat, serrated, spring handle.Overall length 117mm.

#2300 Straight blades. #2301 Curved blades.


page 65


SISSORS

IRIS SCISSORS, RIBBON HANDLE

Pointed blades. Ribbon handle. Overall length 103mm.

#2554 Straight 13mm blades.#2555 Curved 13mm blades.#2556 Straight, large blades.#2557 Curved, large blades.

MCPHERSON-VANNAS IRIS SCISSORS

11mm, curved blades with pointed tips. Flat, serrated, springhandle. Overall length 84mm.

#2350

MICRO IRIS SCISSORS

10mm blades, pointed tips. Flat, serrated, spring handle. Overalllength 103mm.

#2304 Straight.#2305 Curved.

OCUTEK IRIS SCISSORS

22mm blades with pointed tips. Ring handle. Overall length100mm.

#2580 Straight blades.#2581 Curved blades.

page 66




SISSORS

OCUTEK RETINAL SCISSORS � TITANIUM

20 gauge shaft, Round, knurled, squeeze handle. Made of high-grade, lightweight titanium. Overall length 165mm.

#0290

FINE STITCH SCISSORS

16.5mm, straight, pointed blades. Overall length 134mm.

#2220 Standard spring handle.#2224 Wide spring handle.

WESTCOTT STITCH SCISSORS

21mm, curved blades with pointed tips. Flat, serrated spring han-dle. Overall length 115mm.

#2210

WESTCOTT STITCH SCISSORS, WIDE HANDLE

20mm, curved blades with pointed tips. Wide, flat, serratedspring handle. Overall length 117mm.

#2211

KNAPP STRABISMUS SCISSORS

26mm blades with blunt tips. Ring handle. Overall length 118mm.

#2650 Straight blades.#2651 Lightly curved blades.#2652 Strongly curved blades.

STRABISMUS SCISSORS

25mm blades with blunt tips. Ribbon handle. Overall length102mm.

#2660 Straight blades.#2661 Curved blades.#2662 Strongly curved blades.


page 67


SISSORS

STEVENS TENOTOMY SCISSORS

31.5mm tapered blades with blunt tips. Ring handle. Overalllength 114mm.

#2610 Straight.#2611 Curved.#2620 Straight blades.#2621 Curved blades.

STEVENS TENOTOMY SCISSORS, HEAVY

Heavy model with 12mm, straight tapered blades and blunt tips.Ribbon handle. Overall length 95mm.

#2622

WESTCOTT MEDIUM TENOTOMY SCISSORS

Medium, curved tapered blades. Flat, serrated, spring handle.Overall length 112mm.

#2204

WESTCOTT TENOTOMY SCISSORS

20mm tapered blades with blunt tips. Flat, serrated, spring han-dle. Overall length 117mm.

#2200 Right.#2201 Left.

WESTCOTT TENOTOMY SCISSORS, WIDE HANDLE

20mm, tapered blades with blunt tips. Wide, flat, serrated,spring handle. Overall length 136mm.

#2202 Right.#2203 Left.

EYE SCISSORS

Standard, 27mm blades with pointed tips. Ring handle. Overalllength 110mm.


page 68





page 69

SISSORS

EYE SCISSORS, RIBBON HANDLE

22mm blades with pointed tips. Ribbon handle. Overall length102mm.


OCUTEK EYE SCISSORS

Angled shafts with blunt probe tips. Ring handle. Overall length112mm.

#2730

SHEPARD-CASTROVIEJO SCISSORS

Curved, rounded blades with blunt tips. Serrated upper blade.Flat, serrated, spring handle. Overall length 116mm.

#2294

WILMER CONJUNCTIVAL SCISSORS

13mm angled blades with pointed tips. Right handle. Overalllength 94mm.

#2578


SISSORS

MCPHERSON-WESCOTT CONJUNCTIVAL SCISSORS

Curved blades with blunt tips. Flat, serrated spring handle.Overall length 101mm.

#2205

SCLERAL DEPRESSORS

GASS SCLERAL MARKER

Thimble style marker with 1.5mm trephine-like tip produces aring shaped impression when applied to the sclera. Large size 12,thimble. Marker length 21mm.

#7809

SCHEPENS SCLERAL DEPRESSOR

Thimble style depressor with 8mm wide tip. Overall length43mm, 1.7 inches.

#7806 Size 8, small thimble.#7807 Size 10, medium thimble.#7808 Size 12, large thimble.

SCHOCKETT DOUBLE-ENDED SCLERAL DEPRESSOR

2.5mm teardrop end used to depress sclera while 6mm bar endused for reaching behind globe.

#7800

URETTS-ZAVALIA DEPRESSOR AND FIXATION PICK

Permits rotation of the globe during examination. Overall length123mm.

#7804

WILDER SCLERAL DEPRESSOR

Angled shaft with 2.5mm diameter.

#7802

page 70




SCRAPERS AND POLISHERS

DREWS CAPSULE POLISHER

25 gauge cannulated shaft with 2.5mm ring tip. Cannula port islocated at 12 o�clock on interior portion of right. Sandblastedposterior surface of right. Shaft length 23mm.

#6453

JENSEN CAPSULE POLISHER

Gently curved shaft with sandblasted olive tip.


KNOLLE CAPSULE SCRAPER

2mm, angled, sandblasted tip.

#6624 23 gauge cannulated shaft. Shaft length 22mm.#6625 30 gauge cannulated shaft. Shaft length 19mm.

KRATZ CAPSULE SCRAPER

23 gauge, cannulated shaft with 1mm, angled, sandblasted tip.Shaft length 21mm.

#6623

SIMCOE CAPSULE SCRUBBER

23 gauge, curved, cannulated shaft with sandblasted tip. Shaftlength 13mm.

#6429

SIMCOE POSTERIOR CAPSULE POLISHER

23 gauge, angled, cannulated shaft with sandblasted tip. Shaftlength 16mm.

#6425

SIMCOE POSTER CAPSULE SCRUBBER

23 gauge, curved, cannulated 14mm shaft with reverse aperature.Shaft length 29mm.

#6430


page 71


SNARES AND SPOONS

BUNGE ENUCLEATION SPOON

Flat, smooth handle.

#2950 Small size. 8mm spoon. Overall length 136mm.#2951 Large size. 12mm spoon. Overall length 140mm.

FOSTER ENUCLEATION SNARE

Only to be used with #2959 twisted snare wire.

#2958

OCUTEK TWISTED SNARE WIRE

Designed for use with the Foster Enucleation Snare. Packageincludes 12 stainless steel wires. Overall length 135mm.

#2959

WELLS ENUCLEATION SPOON

21mm diameter, curved, notched spoon. Flat, smooth handle.Overall length 140mm.

#2955

SPATULAS

BARRAQUER CYCLODIALYSIS SPATULA

Angled shaft with 0.5mm by 16mm gently curved blade andpointed tip Overall length 120mm.

#7222

BARRAQUER IRIS SPATULA

Angled shaft with gently curved blade. Short, hexagonal handle.Overall length 95mm.

#7220 0.5mm by 13mm blade.#7221 0.25mm by 13mm blade.

page 72




SPATULAS

CASTROVIEJO DOUBLE-ENDED CYCLODIALYSIS SPATULA

Double-ended spatula with 10mm and 15mm length blades. Flat,serrated handle. Overall length 139mm.

#7258 .25mm width blades. #7260 .50mm width blades.#7262 .75mm width blades.

CASTROVIEJO DOUBLE-ENDED SYNECHIA SPATULA

Double-ended spatula with 0.5mm by 10mm and 0.5mm by 15mmblade lengths. Flat, serrated handle. Overall length 131mm.

#7250

CULLER IRIS SPATULA

1mm wide, sterling silver blade. Flat, smooth handle. Overalllength 128mm.

#7206

ELSCHNIG CYCLODIALYSIS SPATULA

28mm, angled tip with gently curved blade. Flat, smooth handle.Overall length 130mm.

#7212

HIRSCHMAN IRIS LENS SPATULA

10mm, angled blade with notches on sides and tip. Round,knurled handle. Overall length 112mm.

#7619

IRIS SPATULA

1mm wide, malleable, stainless steel blade. Flat, smooth handle.Overall length 129mm.

#7205

IRIS SPATULA, WIDE

2mm wide, sterling silver blade. Flat, serrated handle. Overalllength 132mm.

#7203

JOHNSON SPATULA

0.25mm by 10mm blade. Round, knurled handle. Overall length87mm. Ideal for bimanual phaco procedure.

#7214


page 73


SPATULAS

KELMAN CYCLODIALYSIS CANNULA

19 gauge, flattened and angled, cannulated shaft. Shaft length27mm.

#6412 Right side port.#6413 Left side port.

KIMURA PLATINUM SPATULA

33mm by 3.2mm spatula blade. Flat, smooth handle. Overalllength 156mm.

#7440

KNOLLE LENS NUCLEUS SPATULA

and Anterior Chamber GaugeFlat, curved, 1mm spatula blade with calibrations at 5mm, 6mmand 7mm from tip. Round, knurled handle. Overall length126mm.

#7270

PATON SPATULA AND SPOON

Double-ended. Straight shaft with angled spatula blade on oneend with fenestrated spoon on the opposite end. Flat, serratedhandle. Overall length 143mm.

#7265

RANDOLPH CYCLODIALYSIS CANNULA

Angled, cannulated shaft.

#6410 18 gauge. Shaft length 28mm.#6411 21 gauge. Shaft length 30mm.

SIMCOE NUCLEUS SPATULA

Angled, 25 gauge, cannulated shaft. Shaft length 31mm.

#6427

WHEELER CYCLODIALYSIS SPATULA

Sterling silver, double ended spatula with 1.5mm blades. Flat, ser-rated handle. Overall length 131mm.

#7320

page 74




SPECULA

ALFONSO EYE SPECULUM

Wire speculum for newborn infants. Fenestrated, 5mmblades. Overall length 45mm.

#5107

BARRAQUER EYE SPECULUM

Wire speculum with fenestrated blades.

#5100 Adult size. 14mm blades. 18mm blade spread.#5102 Pediatric size. 11mm blades. 12mm blade spread.

BARRAQUER EYE SPECULUM, HEAVY

Heavy weight wire speculum. 14mm blades. 20mm bladespread

#5109

BARRAQUER EYE SPECULUM, SOLID BLADE

Wire speculum with solid blades

#5103 Pediatric size. 11mm blades.12mm blade spread.#5103 Pediatric size. 11mm blades.12mm blade spread.#5105 Adult size. 14mm blades.17mm blade spread.#5105 Adult size. 14mm blades.18mm blade spread.

CASTROVIEJO EYE SPECULUM

Fenestrated blades with screw controlled spread.

#5160 Small size. 12mm blades. Length 72mm.#5161 Medium size. 14mm blades. Length 78mm.#5162 Large size. 16mm blades. Overall length 82mm.


page 75


SPECULAS

COOK EYE SPECULUM

Solid blades with locking mechanism.

#5181 Infant size. 7mm blades. Overall length 52mm.#5182 Pediatric size. 10mm blades. 27mm blade spread.Overall length 48mm.#5183 Adult size. 15mm blades. 27mm blade spread. Overalllength 55mm.

GUYTON-PARK EYE SPECULUM

Featuring suture posts and canthus bar. Overall length 83mm.

#5125 14mm fenestrated blades. 48mm blade spread.#5126 14mm solid blades. 48mm blade spread.

KNAPP EYE SPECULUM

Open 13mm blades. Screw controlled locking mechanism.Overall length 80mm.

#5180

KRATZ-BARRAQUER EYE SPECULUM

Wire speculum with open blades.

#5104 Adult size. 14mm blades. 18mm blade spread.#5106 Pediatric size. 11mm blades. 12mm blade spread.

page 76




SPECULA

LANCASTER EYE SPECULUM

Solid, 15mm blades. Screw controlled locking mechanism. 35mmblade spread. Overall length 80mm.

#5150

LESTER BURCH EYE SPECULUM

Solid, 21mm blades. Screw controlled locking mechanism.Overall length 85mm.

#5170

LIEBERMAN OPEN WIRE SPECULUM

Adjustable wire speculum with 14mm, open blades and lockingmechanism. 45° angled shaft. Overall length 68mm.

#5144

MAUMENEE-PARK EYE SPECULUM

Featuring suture posts and canthus bar. Blade locking screwsallow blades to be positioned and locked vertically and horizontal-ly. 14mm blades. 45mm blade spread. Overall length 100mm.

#5130 Fenestrated blades.#5131 Solid blades.


page 77


SPECULA

MCPHERSON EYE SPECULUM

Features suture posts and stabilizing disk. 14mm free swingingblades. 35mm blade spread. Overall length 83mm.

#5133

MELLINGER EYE SPECULUM

Self locking mechanism. Overall length 68mm.

#5164 Fenestrated 15mm blades.#5165 Solid 15mm blades.

SAUER EYE SPECULUM, INFANT

Solid blade speculum for infants. 10mm blades. 20mm bladespread. Overall length 30mm.

#5190

TEMPORAL WIRE SPECULUM

Wire speculum with spring toward nasal side leaving temporal sideunobstructed. Overall length 35mm.

#5110 Closed wire blades.#5111 Solid blades.$5112 Open wire blades.

page 78




SPECULA

WILLIAMS EYE SPECULUM

Spring controlled spread of blades with locking mechanism.

#5142 14mm fenestrated blades. Overall length 76mm.#514311mm fenestrated blades. Overall length 69mm.

TITANIUM

BARRAQUER NEEDLE HOLDER, TITANIUM

9mm, delicate, curved jaws. Round, knurled handle with hingespring. Made of high-grade, lightweight titanium. Overall length110mm.

#0392 Locking handle.#0393 Standard handle.

BARRETT LENS FOLDING FORCEPS, TITANIUM

20° angled shafts. Flat, serrated, fenestrated, Cross-action han-dle. Made of high-grade, lightweight titanium. Overall length105mm.

#0132

BARRETT LENS HOLDING FORCEPS, TITANIUM

30° angled shafts with 10mm, curved jaws. Flat, serrated, fenes-trated, reverse Cross-action handle. Made of high-grade, light-weight titanium. Overall length 115mm.

#0133

BROWN NUCLEUS CRACKER, TITANIUM

Straight shafts with 1.5mm x 1.2mm paddle style tips. Flat, ser-rated, Cross-action handle. Made of high-grade, lightweight tita-nium. Overall length 95mm

#0130

CASTROVIEJO CORNEAL SCISSORS, TITANIUM

5mm, curved blades with blunt tips. Flat, serrated, spring handle.Overall length 95mm.

#0401 Right#0402 Left


page 79


TITANIUM

CASTROVIEJO MINI CORNEAL SCISSORS � TITANIUM

Curved, 6mm blades. Flat, serrated, spring handle. Made of high-grade, lightweight titanium. Overall length 116mm.

#0403

CASTROVIEJO SUTURING FORCEPS, TITANIUM

Straight shafts with 6mm tying platforms. Tips feature 0.3mm, 1x 2 teeth. Flat, fenestrated, serrated handle. Made of high-grade, lightweight titanium. Overall length 115mm.

#0114

FINE-THORNTON FIXATION RING, TITANIUM

¾, 16mm diameter ring with 9 point fixation. Round, knurledhandle. Made of high-grade, lightweight titanium. Overall length127mm.

#0502

HOFFMAN POLACK FIXATION FORCEPS � TITANIUM

Curved shafts. Tips feature two sets of 1 x 2, 0.12mm teeth sep-arated by 1.6mm. Round, cross-action handle with lock. Made ofhigh-grade, lightweight titanium. Overall length 127mm.

#0117

INAMURA CAPSULORHEXIS FORCEPS, TITANIUM

45° angled shafts with angled tips. Flat, serrated, fenestrated,cross-action handle. Made of high-=grade, lightweight titanium.Overall length 105mm. 2.0mm cross-action shaft ideal for work-ing in small incision environment.

#0129

MALONEY KERATOMETER � TITANIUM

Concentric rings provide reflection of cornea. Made of high-grade, lightweight titanium.

#0600

page 80




TITANIUM

MENDEZ DEGREE GAUGE � TITANIUM

Ring gauge calibrated every 10° from 0° to 180°. Round, knurledhandle. Overall length 108mm. Used for accurate alignment ofcorneal incisions for correction of astigmatism. Made of high-grade, lightweight titanium.

#0536

O�GAWA SUTURING FORCEPS, TITANIUM

Straight shafts with 6mm tying platforms. Tips feature 0.12mm, 1x 2 teeth. Round, knurled handle. Made of high-grade, light-weight titanium. Overall length 109mm.

#0115

OCUTEK LENS FOLDING FORCEPS, TITANIUM

Angled shafts with conical, paddled tips. Flat, serrated, fenestrat-ed handle. Made of high-grade, lightweight titanium.

#0131

OCUTEK NEEDLE HOLDER � TITANIUM

7mm, delicate, curved jaws. Round, knurled handle. Made ofhigh-grade lightweight titanium. Overall length 107mm.

#0390 Standard handle.#0391 Locking handle.

OCUTEK NUCLEUS DIVIDER, TITANIUM

Angled shaft with angled, cutting tip. Round, knurled handle.Made of high-grade, lightweight titanium. Overall length 124mm.

#0539

OCUTEK RETINAL FORCEPS � TITANIUM

20 gauge shaft. Round, knurled, squeeze handle. Made of high-grade, lightweight titanium. Overall length 158mm.

#0280 Smooth, 1.0mm tips. Vertical action.#0281 Smooth, 3.5mm tips. Vertical action.


page 81


TITANIUM

OCUTEK RETINAL FORCEPS � TITANIUM (CONT.)


#0282 Smooth 2.0mm tips. Vertical action.#0283 Smooth, rounded, 2.5mm tips. Horizontal action.#0284 Smooth, rounded, 2.0mm tips. Horizontal action.#0285 2.5mm, cusp style jaws.#0286 2.0mm jaws with 0.7mm platforms.

OCUTEK RETINAL SCISSORS, TITANIUM


#0290

SINSKEY HOOK � TITANIUM

Angled shaft with angled tip. Round, knurled handle. Made ofhigh-grade, lightweight titanium. Overall length 118mm.

#0538

TROUTMAN BARRAQUER COLIBRI FORCEPS � TITANIUM

Curved shafts with angled tips. Tips feature 0.12mm 1x 2 teeth.Colibri-stye, fenestrated handle. Made of high-grade, lightweighttitanium. Overall length 78mm.

#0116

page 82




TREPHINES AND PUNCHES

GASS SCLEROTOMY PUNCH

Vertical punch designed to create a 1.5mm, clean, cylindrical hold.Rotatable for convenient positioning. Flat handle. Overall length87mm.

#1752

HOLTH CORNEOSCLERAL PUNCH

1mm by 7mm horizontal punch. Flat, serrated handle. Overalllength 87mm.

#1754

IOWA P.K. PRESS

Central platform with integrated neck. Piston assembly fits intoneck of platform utilizing an internal spring to recoil to readyposition after use. Cutting block fits into precision milled cavity inplatform. Accepts disposable trephine blades sized 6.25-9.0mm.Designed for use in the preparation of corneal donor buttons foruse in penetrating karatoplasty.

#1760 Complete set.#1761 Cutting block.#1762 Vacuum suction block.

page 83




KELLY DESCEMET�S MEMBRANE PUNCH

Vertical punch designed to produce a clean, 0.75mm round holewithout tissue tags. Serrated, squeeze handle. Overall length130mm.

#1751

TROUTMAN CORNEAL PUNCH

Adjustable piston accommodates 7-9mm trephine blade.Complete punch includes base place, piston carrier, piston for 7-9mm trephine blades and 18mm diameter TEFLON block.Designed for accurate donor button preparation.

#1728 Complete punch.#1741 Piston for 7-9mm trephine blades.#1742 Piston for 5-7mm trephine blades.#1743 Piston for 9-11mm trephine blades.#9729 Replacement TEFLON block.

SOLAN DISPOSABLE TREPHINE BLADES

Handcrafted, sharp, uniform edges promote a symmetrical andvertical cut of all corneal layers. Single use, packaged sterile.Available sizes 5-17mm.

#00-09701 5.0mm diameter.#00-09703 5.5mm diameter.#00-09705 6.0mm diameter.#00-09706 6.25mm diameter.#00-09707 6.5mm diameter.#00-09708 6.75mm diameter.#00-09709 7.0mm diameter.#00-09719 7.25mm diameter.#00-09711 7.5mm diameter.#00-09722 7.75mm diameter.#00-09710 7.85mm diameter.#00-09713 8.0mm diameter.#00-09727 8.25mm diameter.#00-09715 8.5mm diameter.#00-09723 8.75mm diameter.#00-09717 9.0mm diameter.#00-09721 10.0mm diameter.#00-09725 11mm diameter.#00-09726 12mm diameter.#00-09720 13mm diameter.#00-09728 14mm diameter.#00-09724 15mm diameter.#00-09730 16mm diameter.#00-097301 17mm diameter.

page 84





page 85


SOLAN CALIBRATED TREPHINE HANDLE

Each handle is designed to fit a specific trephine size. Protectivedepth guard. Overall length 73mm without trephine blade. Foruse in performing uniform, free-hand donor buttons.

#1672 5.0mm. #1673 5.5mm.#1674 6.0mm. #1675 6.25mm.#1683 6.5mm. #1676 6.75mm.#1684 7.0mm. #1677 7.25mm.#1685 7.5mm. #1678 7.75mm.#1686 8.0mm. #1679 8.25mm.#1687 8.5mm. #1680 8.75mm.#1688 9.0mm. #1690 10.0mm.

SOLAN OPEN TREPHINE HANDLE

Each handle is designed to fit a specific trephine size.

#9732 5.0mm. #9733 5.5mm.#9734 6.0mm. #9735 6.5mm.#9736 7.0mm. #9737 7.25mm.#9738 7.5mm. #97397.75mm.#9740 8.0mm. #9741 8.2mm.#9742 8.5mm. #97438.75mm.#9744 9.0mm. #974510.0mm.#9746 11.0mm.

SOLAN TREPHINE HANDLE

Each handle is designed to fit a specific trephine size. Overalllength 50mm without trephine blade.

#1700 5.0mm. #1702 5.5mm. #1704 6.0mm.#1706 6.5mm. #1708 7.0mm. #1710 7.5mm.#1712 8.0mm. #1714 8.5mm.#1716 9.0mm. #1720 10.0mm.#1724 11.0mm.

SOLAN TREPHINE WITH HANDLE

Reusable, stainless steel trephine with handle. Overall length53mm.

#9747 1.0mm. #97481.5mm#9749 2.0mm. #97523.5mm.#9753 4.0mm.



TROUTMAN TREPHINE HANDLE

Adjustable trephine handle to fit disposable, stainless steeltrephine blades.

#1735 Fits 5mm � 7mm trephine.#1737 Fits 7mm � 9mm trephines.#1739 Fits 9mm � 11mm trephines.

BEYER RONGEUR

Straight jaws with 2mm bite. Cross-action handle. Overalllength 178mm.

#6724

CITELLI BONE RONGEUR

Straight, 13mm shaft with 1.5mm x 4mm bite. Spring action,squeeze handle. Handle length 85mm.

#6723

FREER LACRIMAL CHISEL

Straight shaft with chisel head. Round, knurled handle. Overalllength 126mm.

#6706 Straight tip.#6707 Curved tip.

FREER PERIOSTEAL ELEVATOR

Double-ended with one blunt end and one semi-sharp end.4.5mm wide blades. Flat handle. Overall length 141mm.

#6700

JOSEPH PERIOSTEAL ELEVATOR

Straight shaft with gently curved tip. Flat, grooved handle.Overall length 129mm.

#6702

page 86





page 87


KERRISON RONGEUR

Straight, 110mm shaft with 9.0mm opening. Spring action,squeeze handle. Overall length 135mm.

#6720 Size 0, 3.5mm bite.#6721 Size 1, 4.0mm bite.#6722 Size 2, 4.5mm bite.

MALLET

Lead filled mallet with flat, grooved handle. Overall length170mm.

#6709

MALONEY KERATOMETER � TITANIUM

Concentric rings provide reflection on cornea. Made of high-grade, lightweight titanium.

#0600

NASAL SPECULUM

Spring action handle. Overall length 134mm.

#6710 Size #1, 28mm blades.#6711 Size #2, 30mm blades.#6712 Size #3, 32mm blades.

WEST LACRIMAL CHISEL

Straight shaft with wide chisel head. Round, knurled handle.Overall length 135mm.

#6704


DIAMOND KNIVES

DIAMONTEK AK KNIFE

Swiss precision, ultra-thin, 15°, triple-edge blade set in straightmount. Titanium handle with high precision micrometer. Highlypolished, parallel footplates. Overall length 113mm. Designed forarcuate or transverse astigmatic keratotomy incisions. Completewith DiamonTek storage and sterilization try (#1064)

#83-90615 1.0mm blade width, 0.2mm thickness.

DIAMONTEK ANGLED CLEAR CORNEA KERATOME

Swiss precision, double-beveled, gem-quality blade with sharpsides set in angled mount. Titanium handle with J-slot retractionmechanism. Overall length 116mm. Ideal for clear cornea incisioninto anterior chamber. Complete with DiamonTek storage andsterilization tray (#1064).

#83-90225 2.5mm blade width, 0.2mm thickness.#83-90230 3.0mm blade width, 0.2mm thickness.#83-90232 3.2mm blade width, 0.2mm thickness.

DIAMONTEK ANGLED KERATOME, DULL SIDES

Swiss precision, double-beveled, gem-quality blade with dull sidesset in angled mount. Titanium handle with J-slot retractionmechanism. Overall length 116mm. Designed for anterior cham-ber entrance. Complete with DiamonTek storage and steriliza-tion tray (#1064).


page 88




KNIVES

DIAMONTEK ANGLED TRAPEZOID KNIFE

Swiss precision, trapezoid shaped, gem-quality blade with sharpsides set in angled mount. Titanium handle with J-slot retractionmechanism. Overall length 115mm. Ideal for clear cornea incisioninto anterior chamber. Complete with DiamonTek storage andsterilization tray (#1064).

#83-90330 Trapezoid blade width measures from 3.0mm at shoulder to 3.33mm at base.

#83-90332 Trapezoid blade width measures from 3.2mm at shoulder to 3.5mm at base.

DIAMONTEK CRESCENT BLADE

Swiss precision, crescent shaped, gem-quality blade with sharpsides set in angled mount. Titanium handle with J-slot retractionmechanism. Overall length 115mm. Ideal for dissection andwound extension. Complete with DiamonTek storage and sterili-zation tray (#1064).


DIAMONTEK ECONO BLADE

Swiss precision, gem-quality blade set in straight mount. 1.0mmblade width, 0.2mm thickness. Titanium handle with J-slot retrac-tion mechanism. Overall length 116mm. Complete with DiamonTek storage and sterilization tray (#1064).

#83-90000 Trifaceted blade designed for scleral groove and tun-nel incision.#83-90045 Single edge, 45 degree blade designed for side portincision and scleral groove.

DIAMONTEK ROUND BLADE

Swiss precision, round shaped, gem-quality blade with sharp sidesset in angled mount. Titanium handle with J-slot retraction mech-anism. Overall length 114mm. Ideal for tunnel incision and woundextension. Complete with DiamonTek storage and sterilizationtray (#1064).



page 89


KNIVES

DIAMONTEK STEP KERATOME

Swiss precision, double beveled, gem-quality blade with sharpsides set in straight mount. Titanium handle with high precisionmicrometer. Preset steps from 150 microns to 66mm. Overalllength 120mm. Ideal for clear cornea incision into anterior cham-ber. Complete with DiamonTek storage and sterilization tray(#1064).


DIAMONTEK STEP KNIFE

Swiss precision, gem-quality blade set in straight mount.Titanium handle with high precision micrometer. Preset stepsfrom 150 microns to 4mm. Overall length 108mm. Completewith DiamonTek storage and sterilization tray (#1064).

#83-90500 Trifaceted blade with single footplate. Designed for creating initial groove, tunneling and stab incisions.

#83-90545 45 degree, double-edged blade with single footplate. Designed for creating initial groove, tunneling and stab incisions.

DIAMONTEK STORAGE AND STERILIZATION TRAY

Lightweight storage and sterilization tray designed to hold onediamond knife. 5� L x 2� W x 0.7� D.

#1064

page 90




Instrument catalog

Health & Medicine

Transcript of Instrument catalog