Increasing Acoustic Performance Why choose Farrat VR16 ...Density BS EN ISO 845 270 Kg/m3 Tensile...
Transcript of Increasing Acoustic Performance Why choose Farrat VR16 ...Density BS EN ISO 845 270 Kg/m3 Tensile...
DATA SHEETDATA SHEET
VERLIMBER VR16 (Cyan)Expanded Polyurethane Vibration Isolation Foam
AVM - VR16 - 14a
Why choose Farrat VR16?Farrat Verlimber is a range of premium grade vibration isolation materials used for low pressure applications. It is produced from high quality polyurethane using an innovative blown expansion method.
Farrat Verlimber VR16 provides excellent low frequency vibration isolation whilst withstanding high repeated strains without loss of performance. This allows very high levels of acoustic performance to be achieved in lightweight structures.
Features❫ High resilience with very good low frequency isolation
and damping performance.
❫ Excellent for repeated compression cycle applications(up to 45% strain)
❫ Long working lifetime (>60 years)
❫ Waterproof and non-absorbing
❫ Available in 270 grade (VR27) and 385 grade (VR38) forhigher pressures
Can be supplied as full sheets, cut to size pads and strips (including holes and slots if required) according to the customer's requirements.
ApplicationsFarrat Verlimber VR16 can be used in a wide range of noise and vibration applications, such as:
Full Area❫ Full building (raft-slab)❫ Soil pressure bearing support❫ Movement joints
Strips❫ Partition loading❫ Corbels❫ Timber frame supports
Pads❫ Bespoke low-load isolation❫ Steel/timber frame isolation❫ General anti-vibration pads
Verlimber VR16 site applications:
Verlimber VR16 used to isolate light-weight timber structuresSee Farrat Application Document AVP-PLAS-14a for more information.
Increasing Acoustic Performance
FARRAT VERLIMBER RANGE:
Increasing Load Bearing Capacity
VR16 VR27 VR38
For more information on using Verlimber VR16 (including standard details), please see the following Farrat Technical Brochures:
Applications - Cinemas Applications - Timber Stadia Seating
Available to download at: www.farrat.com
AVM - VR16 - 17aDATA SHEET
VERLIMBER VR16 (Cyan)Expanded Polyurethane Vibration Isolation Foam
AVM - VR16 - 14a
Why choose Farrat VR16?Farrat Verlimber is a range of premium grade vibration isolation materials used for low pressure applications. It is produced from high quality polyurethane using an innovative blown expansion method.
Farrat Verlimber VR16 provides excellent low frequency vibration isolation whilst withstanding high repeated strains without loss of performance. This allows very high levels of acoustic performance to be achieved in lightweight structures.
Features❫ High resilience with very good low frequency isolation
and damping performance.
❫ Excellent for repeated compression cycle applications(up to 45% strain)
❫ Long working lifetime (>60 years)
❫ Waterproof and non-absorbing
❫ Available in 270 grade (VR27) and 385 grade (VR38) forhigher pressures
Can be supplied as full sheets, cut to size pads and strips (including holes and slots if required) according to the customer's requirements.
ApplicationsFarrat Verlimber VR16 can be used in a wide range of noise and vibration applications, such as:
Full Area❫ Full building (raft-slab)❫ Soil pressure bearing support❫ Movement joints
Strips❫ Partition loading❫ Corbels❫ Timber frame supports
Pads❫ Bespoke low-load isolation❫ Steel/timber frame isolation❫ General anti-vibration pads
Verlimber VR16 site applications:
Verlimber VR16 used to isolate light-weight timber structuresSee Farrat Application Document AVP-PLAS-14a for more information.
Increasing Acoustic Performance
FARRAT VERLIMBER RANGE:
Increasing Load Bearing Capacity
VR16 VR27 VR38
Farrat Isolevel Ltd Balmoral Road, Altrincham, WA15 8HJ, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
Farrat Isolevel Ltd Balmoral Road, Altrincham, Cheshire, WA15 8HJ, England, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
0
2
4
6
8
10
12
14
16
18
20
22
0.00 0.01 0.02 0.03 0.04 0.05 0.06
Def
lect
ion
(mm
)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad 50mm
25mm
12.5mm
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0.00 0.01 0.02 0.03 0.04 0.05 0.06
Nat
ural
Fre
quen
cy (
Hz)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad
12.5mm
25mm
50mm
Static Deflection
Natural Frequency
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0 10 20 30 40 50 60 70 80 90 100
Isol
ator
Nat
ural
Fre
quen
cy (
Hz)
Disturbing Frequency (Hz)
0% 44% 68% 82% (0dB) (-5dB) (-10dB) (-15dB)
90%
94%
97%
98%
99%
(-20dB)
(-25dB)
(-30dB)
(-35dB)
(- 40dB)
Availability
Typical Lead Times
Key
Isolation Efficiency (Transmissibility)
THICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 mm Woven/Woven Bespoke
STOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5mm
25 mm
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Hardness Asker C* 8 (+/-3) IRHD
Density BS EN ISO 845 160 Kg/m3
Tensile Strength ISO 1798:2008 0.55 N/mm2
Elongation at Break ISO 1798:2008 >250 %
Compression Set (70hrs@23¡C)
ISO 1856:2000 <5 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 3.2% per
decade
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness - see graphs
Dynamic to Static Ratio
Determined using in-house test methodology
1.7 N/A
Damping Ratio, C/Cc @ fn 9.4 %
Max Static Pressure [Overload]
0.035 [0.052]
N/mm2
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 ¡C
Operational Life N/A 60 Years* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
Data based on material damping specific, single degree of freedom model.
Model applies to all thicknesses.
Hardness Asker C* 8 (+/-3) IRHD
Density BS EN ISO 845 160 Kg/m³
Tensile Strength ISO 1798:2008 0.55 N/mm²
Elongation at Break ISO 1798:2008 >250 %
Compression Set (24hrs@70°C)
ISO 1856:2000 <5 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 3.2% per
decade
* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness – see graphs
Dynamic to Static Ratio
Determined using in-house test methodology.
Test pad dimensions:75 x 75mm
1.7 N/A
Damping Ratio, C/Cc @ f
n9.4 %
Max Static Pressure [Overload]
0.035 [0.052]
N/mm²
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 °C
Operational Life N/A 60 Years
AvailabilityTHICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 Woven/Woven Bespoke
Typical Lead TimesSTOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5 mm
25 mm
Key
Farrat Isolevel Ltd Balmoral Road, Altrincham, Cheshire, WA15 8HJ, England, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
0
2
4
6
8
10
12
14
16
18
20
22
0.00 0.01 0.02 0.03 0.04 0.05 0.06
Def
lect
ion
(mm
)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad 50mm
25mm
12.5mm
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0.00 0.01 0.02 0.03 0.04 0.05 0.06
Nat
ural
Fre
quen
cy (
Hz)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad
12.5mm
25mm
50mm
Static Deflection
Natural Frequency
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0 10 20 30 40 50 60 70 80 90 100
Isol
ator
Nat
ural
Fre
quen
cy (
Hz)
Disturbing Frequency (Hz)
0% 44% 68% 82% (0dB) (-5dB) (-10dB) (-15dB)
90%
94%
97%
98%
99%
(-20dB)
(-25dB)
(-30dB)
(-35dB)
(- 40dB)
Availability
Typical Lead Times
Key
Isolation Efficiency (Transmissibility)
THICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 mm Woven/Woven Bespoke
STOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5mm
25 mm
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Hardness Asker C* 8 (+/-3) IRHD
Density BS EN ISO 845 160 Kg/m3
Tensile Strength ISO 1798:2008 0.55 N/mm2
Elongation at Break ISO 1798:2008 >250 %
Compression Set (70hrs@23¡C)
ISO 1856:2000 <5 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 3.2% per
decade
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness - see graphs
Dynamic to Static Ratio
Determined using in-house test methodology
1.7 N/A
Damping Ratio, C/Cc @ fn 9.4 %
Max Static Pressure [Overload]
0.035 [0.052]
N/mm2
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 ¡C
Operational Life N/A 60 Years* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
Data based on material damping specific, single degree of freedom model.
Model applies to all thicknesses.
DATA SHEETDATA SHEET
VERLIMBER VR27 (Violet)Expanded Polyurethane Vibration Isolation Foam
AVM - VR27 - 14a
Why choose Farrat VR27?Farrat Verlimber is a range of premium grade vibration isolation materials used for low pressure applications. It is produced from high quality polyurethane using an innovative blown expansion method.
Farrat Verlimber VR27 provides excellent low frequency vibration isolation whilst withstanding high repeated strains without loss of performance. This allows very high levels of acoustic performance to be achieved in lightweight structures.
Features❫ High resilience with very good low frequency isolation
and damping performance.❫ Excellent for repeated compression cycle applications
(up to 45% strain)❫ Long working lifetime (>60 years)❫ Waterproof and non-absorbing❫ Available in 160 grade (VR16) for lower pressures and
385 grade (VR38) for higher pressures
Can be supplied as full sheets, cut to size pads and strips (including holes and slots if required) according to the customer's requirements.
ApplicationsFarrat Verlimber VR27 can be used in a wide range of noise and vibration applications, such as:
Full Area❫ Full building (raft-slab)❫ Soil pressure bearing support❫ Movement joints
Strips❫ Partition loading❫ Corbels❫ Timber frame supports
Pads❫ Bespoke low-load isolation❫ Steel/timber frame isolation❫ General anti-vibration pads
Verlimber VR27 site applications:
Verlimber VR27 used as raft-slab isolation
Verlimber VR27 used as corbel strip isolation
Increasing Acoustic Performance
FARRAT VERLIMBER RANGE:
Increasing Load Bearing Capacity
VR16 VR27 VR38
For more information on using Verlimber VR27 (including standard details), please see the following Farrat Technical Brochures:
Applications - Cinemas Full Building Isolation
Available to download at: www.farrat.com
DATA SHEET
VERLIMBER VR27 (Violet)Expanded Polyurethane Vibration Isolation Foam
AVM - VR27 - 14a
Why choose Farrat VR27?Farrat Verlimber is a range of premium grade vibration isolation materials used for low pressure applications. It is produced from high quality polyurethane using an innovative blown expansion method.
Farrat Verlimber VR27 provides excellent low frequency vibration isolation whilst withstanding high repeated strains without loss of performance. This allows very high levels of acoustic performance to be achieved in lightweight structures.
Features❫ High resilience with very good low frequency isolation
and damping performance.❫ Excellent for repeated compression cycle applications
(up to 45% strain)❫ Long working lifetime (>60 years)❫ Waterproof and non-absorbing❫ Available in 160 grade (VR16) for lower pressures and
385 grade (VR38) for higher pressures
Can be supplied as full sheets, cut to size pads and strips (including holes and slots if required) according to the customer's requirements.
ApplicationsFarrat Verlimber VR27 can be used in a wide range of noise and vibration applications, such as:
Full Area❫ Full building (raft-slab)❫ Soil pressure bearing support❫ Movement joints
Strips❫ Partition loading❫ Corbels❫ Timber frame supports
Pads❫ Bespoke low-load isolation❫ Steel/timber frame isolation❫ General anti-vibration pads
Verlimber VR27 site applications:
Verlimber VR27 used as raft-slab isolation
Verlimber VR27 used as corbel strip isolation
Increasing Acoustic Performance
FARRAT VERLIMBER RANGE:
Increasing Load Bearing Capacity
VR16 VR27 VR38
AVM - VR27 - 17a
Farrat Isolevel Ltd Balmoral Road, Altrincham, WA15 8HJ, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
Hardness Asker C* 13 (+/-3) IRHD
Density BS EN ISO 845 270 Kg/m³
Tensile Strength ISO 1798:2008 1.00 N/mm²
Elongation at Break ISO 1798:2008 >400 %
Compression Set (70hrs@23°C)
ISO 1856:2000 <5 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 1.9% per
decade
* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness – see graphs
Dynamic to Static Ratio
Determined using in-house test methodology.
Test pad dimensions: 75 x 75mm
1.4 N/A
Damping Ratio, C/Cc @ f
n5.5 %
Max Static Pressure [Overload]
0.09 [0.13]
N/mm²
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 °C
Operational Life N/A 60 Years
AvailabilityTHICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 mm Woven/Woven Bespoke
Typical Lead TimesSTOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5 mm
25 mm
Key
Farrat Isolevel Ltd Balmoral Road, Altrincham, Cheshire, WA15 8HJ, England, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
0
2
4
6
8
10
12
14
16
18
20
22
0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14
Def
lect
ion
(mm
)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad
50mm
25mm
12.5mm
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14
Nat
ural
Fre
quen
cy (
Hz)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad
12.5mm
25mm
50mm
Static Deflection
Natural Frequency
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0 10 20 30 40 50 60 70 80 90 100
Isol
ator
Nat
ural
Fre
quen
cy (
Hz)
Disturbing Frequency (Hz)
0% 44% 68% 82% (0dB) (-5dB) (-10dB) (-15dB)
90%
94%
97%
98%
99%
(-20dB)
(-25dB)
(-30dB)
(-35dB)
(- 40dB)
Availability
Typical Lead Times
Key
Isolation Efficiency (Transmissibility)
THICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 mm Woven/Woven Bespoke
STOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5mm
25 mm
* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness - see graphs
Dynamic to Static Ratio
Determined using in-house test methodology
1.4 N/A
Damping Ratio, C/Cc @ fn 5.5 %
Max Static Pressure [Overload]
0.09 [0.13]
N/mm2
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 ¡C
Operational Life N/A 60 Years
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Hardness Asker C* 13 (+/-3) IRHD
Density BS EN ISO 845 270 Kg/m3
Tensile Strength ISO 1798:2008 1.00 N/mm2
Elongation at Break ISO 1798:2008 >400 %
Compression Set (70hrs@23¡C)
ISO 1856:2000 <5 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 1.9% per
decade
Data based on material damping specific, single degree of freedom model.
Model applies to all thicknesses.
Farrat Isolevel Ltd Balmoral Road, Altrincham, Cheshire, WA15 8HJ, England, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
0
2
4
6
8
10
12
14
16
18
20
22
0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14
Def
lect
ion
(mm
)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad
50mm
25mm
12.5mm
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14
Nat
ural
Fre
quen
cy (
Hz)
Pressure (MPa)
MaxWorking
Load
MaxPeakLoad
12.5mm
25mm
50mm
Static Deflection
Natural Frequency
0
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
0 10 20 30 40 50 60 70 80 90 100
Isol
ator
Nat
ural
Fre
quen
cy (
Hz)
Disturbing Frequency (Hz)
0% 44% 68% 82% (0dB) (-5dB) (-10dB) (-15dB)
90%
94%
97%
98%
99%
(-20dB)
(-25dB)
(-30dB)
(-35dB)
(- 40dB)
Availability
Typical Lead Times
Key
Isolation Efficiency (Transmissibility)
THICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 mm Woven/Woven Bespoke
STOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5mm
25 mm
* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness - see graphs
Dynamic to Static Ratio
Determined using in-house test methodology
1.4 N/A
Damping Ratio, C/Cc @ fn 5.5 %
Max Static Pressure [Overload]
0.09 [0.13]
N/mm2
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 ¡C
Operational Life N/A 60 Years
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Hardness Asker C* 13 (+/-3) IRHD
Density BS EN ISO 845 270 Kg/m3
Tensile Strength ISO 1798:2008 1.00 N/mm2
Elongation at Break ISO 1798:2008 >400 %
Compression Set (70hrs@23¡C)
ISO 1856:2000 <5 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 1.9% per
decade
Data based on material damping specific, single degree of freedom model.
Model applies to all thicknesses.
DATA SHEET
For more information on using Verlimber VR16 (including standard details), please see the following Farrat Technical Brochures:
Applications - Cinemas Applications - Timber Stadia Seating
Available to download at: www.farrat.com
AVM - VR38 - 17aDATA SHEET
VERLIMBER VR38 (Graphite)Expanded Polyurethane Vibration Isolation Foam
PERMANENT FORMWORK FOR LATRERAL STABILITY (OPTIONAL) VERLIMBER VR38
VERLIMBER VR38
PERMANENT FORMWORK FOR LATRERAL STABILITY (OPTIONAL) VERLIMBER VR38
VERLIMBER VR38
AVM - VR38 - 14a
Why choose Farrat VR38?Farrat Verlimber is a range of premium grade vibration isolation materials used for low pressure applications. It is produced from high quality polyurethane using an innovative blown expansion method.
Farrat Verlimber VR38 provides excellent low frequency vibration isolation whilst withstanding high repeated strains without loss of performance. This allows very high levels of acoustic performance to be achieved in lightweight structures.
Features❫ High resilience with very good low frequency isolation
and damping performance.❫ Excellent for repeated compression cycle applications
(up to 40% strain)❫ Long working lifetime (>60 years)❫ Waterproof and non-absorbing❫ Available in 160 grade (VR16) and 270 grade (VR27)
for lower pressures
Can be supplied as full sheets, cut to size pads and strips (including holes and slots if required) according to the customer's requirements.
ApplicationsFarrat Verlimber VR38 can be used in a wide range of noise and vibration applications, such as:
Full Area❫ Full building (raft-slab)❫ Soil pressure bearing supports❫ Movement joints
Strips❫ Partition loading❫ Corbels❫ Timber frame supports
Pads❫ Bespoke low-load isolation❫ Steel/timber frame isolation❫ General anti-vibration pads
Verlimber VR38 site applications:
Verlimber VR38 used for block work isolation
Verlimber VR38 used for soil pressure bearing isolation
Increasing Acoustic Performance
FARRAT VERLIMBER RANGE:
Increasing Load Bearing Capacity
VR16 VR27 VR38
For more information on using Verlimber VR38 (including standard details), please see the following Farrat Technical Brochures:
Applications - Cinemas Full Building Isolation
Available to download at: www.farrat.com
DATA SHEET
VERLIMBER VR38 (Graphite)Expanded Polyurethane Vibration Isolation Foam
PERMANENT FORMWORK FOR LATRERAL STABILITY (OPTIONAL) VERLIMBER VR38
VERLIMBER VR38
PERMANENT FORMWORK FOR LATRERAL STABILITY (OPTIONAL) VERLIMBER VR38
VERLIMBER VR38
AVM - VR38 - 14a
Why choose Farrat VR38?Farrat Verlimber is a range of premium grade vibration isolation materials used for low pressure applications. It is produced from high quality polyurethane using an innovative blown expansion method.
Farrat Verlimber VR38 provides excellent low frequency vibration isolation whilst withstanding high repeated strains without loss of performance. This allows very high levels of acoustic performance to be achieved in lightweight structures.
Features❫ High resilience with very good low frequency isolation
and damping performance.❫ Excellent for repeated compression cycle applications
(up to 40% strain)❫ Long working lifetime (>60 years)❫ Waterproof and non-absorbing❫ Available in 160 grade (VR16) and 270 grade (VR27)
for lower pressures
Can be supplied as full sheets, cut to size pads and strips (including holes and slots if required) according to the customer's requirements.
ApplicationsFarrat Verlimber VR38 can be used in a wide range of noise and vibration applications, such as:
Full Area❫ Full building (raft-slab)❫ Soil pressure bearing supports❫ Movement joints
Strips❫ Partition loading❫ Corbels❫ Timber frame supports
Pads❫ Bespoke low-load isolation❫ Steel/timber frame isolation❫ General anti-vibration pads
Verlimber VR38 site applications:
Verlimber VR38 used for block work isolation
Verlimber VR38 used for soil pressure bearing isolation
Increasing Acoustic Performance
FARRAT VERLIMBER RANGE:
Increasing Load Bearing Capacity
VR16 VR27 VR38
Farrat Isolevel Ltd Balmoral Road, Altrincham, WA15 8HJ, UKT. +44 (0) 161 924 1600 F. +44 (0) 161 924 1616 E. [email protected] www.farrat.com
All information in this datasheet is for guidance only based on current knowledge and may be subject to change and correction.
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Hardness Asker C* 24 (+/-3) IRHD
Density BS EN ISO 845 385 Kg/m³
Tensile Strength ISO 1798:2008 1.9 N/mm²
Elongation at Break ISO 1798:2008 >400 %
Compression Set (70hrs@23°C)
ISO 1856:2000 <10 %
Water Absorption Volume Swell - 7 Days* <10 %
Creep ISO 8013:2012* 1.7% per
decade
* Indicates value quoted has been converted from an equivalent standard, or where no standard exists, describes the methodology.
CHARACTERISTICS TEST STANDARD PROPERTIES UNIT
Static Compression Modulus, E
c
Varies with load/thickness – see graphs
Dynamic to Static Ratio
Determined using in-house test methodology.
Test pad dimensions: 75 x 75mm
1.5 N/A
Damping Ratio, C/Cc @ f
n5.7 %
Max Static Pressure [Overload]
0.22 [0.32]
N/mm²
Max Residual Compression After Overload
2.0 %
Standard Sheet Size +/-2% 2000x1000 mm
Operating Temperature N/A -30 to +60 °C
Operational Life N/A 60 Years
AvailabilityTHICKNESS TREAD (Bottom/Top) STOCK
12.5 mm Woven/Woven Non-Stock
25 mm Woven/Woven Stock
Other up to 100 mm Woven/Woven Bespoke
Typical Lead TimesSTOCK 2-3 working days
NON-STOCK 2-3 working weeks
BESPOKE 4-6 working weeks
If cutting is required add +5 days
50 mm 12.5 mm
25 mm
KeyStatic Deflection
Natural Frequency Isolation Efficiency (Transmissibility)