Illuminator User Guide - Complete Fiber Optic and LED Lighting...
Transcript of Illuminator User Guide - Complete Fiber Optic and LED Lighting...
MicroLED Illuminator Range
Models covered by this manual:
UFO MIC1000P
Please read this manual fully before installing, operating or performingmaintenance on the Illuminator unit.
Illuminator User Guide
Issue 1 | Revised: 140114
Universal Fiber Optics6119A Clark Center Avenue | Sarasota | FL34238Tel: 941 343 8115 | 800 UFO 5554www.fiberopticlighting.com
MicroLED Illuminator Range
INTRODUCTIONThank you for purchasing this UFO Illuminator.
Please read these instructions fully before connecting your unit to the electricalsupply, and keep them for future reference.
The UFO MicroLED range of illuminators utilises an RGBW LED array and is suitablefor use with either glass or polymer fiber-optic harness
The MicroLED is powered by a 100-240 VAC remote desktop power supply unit.
IMPORTANTTHIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLEINSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION ANDOPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
2
Universal Fiber Optics 3
INSTALLATION INSTRUCTIONSPOWER SUPPLY REQUIREMENTS
The LED illuminator is powered from a multi-function, multi-voltage, desk top PowerSupply Unit. Remove the SW4047B desk top PSU from its box. This PSU is a multi-plug device catering for UK, European and USA plugs.
Select the correct plug and slide it into the receptacle until it clicks securely intoplace, as shown below:
The plug can be removed by squeezing together the plastic retaining lugs andsliding the plug back out.
Connect the jack plug into the socket in the back, and the illuminator is now readyfor connection.
MicroLED Illuminator Range4
CONNECTION
There are 2 connections required - the fiber port and the mains supply. The fiberport should be connected first. Connect and secure the fiber optic connector intothe front of the unit and secure using the M5 locking screw.
Plug the mains plug into the electrical supply socket. Switch on the power, the LEDindicator will illuminate, and the illuminator will start up automatically. If no light isproduced consult the troubleshooting section.
NOTE: THESE ILLUMINATORS ARE NOT MAINS DIMMABLE.
OPERATION
The LED illluminator has 2 color cycles, each with 3 different speed settings, thecolors are detailed in the table below:
Cycle Color 1 Color 2 Color 3 Color 4 Color 5 Color 6 Color 71 White Red Orange Jade Green Cyan Blue2 Pink Red Orange Jade Green Cyan Blue
The illuminator is controlled using the 2 push buttons on the rear of the unit.The upper button stops and starts the color cycle.The lower button is used to select the cycle speed as follows:
Push the lower button repeatedly until the color white is displayed. The illuminatoris now in Cycle 1 Speed A as detailed in the table below. Each push reduces thespeed. On the third push, the color red will be displayed. The illuminator is now inCycle 2 Speed A.
Cycle Speed A - Fastest Speed B - Slower Speed C - Slowest1 (White Start) Push Once Push Once Push Once
2 (Red Start) Push Once Push Once Push Once
At any time the cycle can be stopped on a color and started again using the upperpush button.
Universal Fiber Optics 5
MAINTENANCE
Date Maintenance Undertaken
Please note that a record of all maintenance MUST be kept in the table below,indicating what maintenance was undertaken and when. This MUST be datedfor warranty purposes.
MicroLED Illuminator Range6
TROUBLESHOOTING
Problem Probable cause(s) Remedy
Unit is dead - LED powerindicator is notilluminated
Mains supply off Check supply and reinstate
Loose mains plugs Check plugs
PSU failed Replace PSU
Unit is dead - no lightoutput but LED powerindicator is stillilluminated
LED array failure Replace LED unit
Poor light output on fiber
Unit needs cleaning
Carefully clean LED Lenswith dry cloth
Clean fiber common end
Fiber port connector notplugged in correctly
Ensure plugged in correctlyand secured with lockingscrew
Stationary on one color
Upper button has beenpressed Press upper button once
LED driver has failed Replace LED unit
Color cycle cannot bestopped LED driver has failed Replace LED unit
Please ensure you have completed the troubleshooting procedures before returning the unit to us.
Universal Fiber Optics 7
TECHNICAL SPECIFICATIONS
Description DetailsPort connector size 1.18” (30mm) diameterFiber type Glass/PMMASupply voltage 110VAC 60Hz / 230VAC 50HzPSU Output 12C DC, 2A, 24W MaximumLED Power 2 - 5W in color cycle modeMin Ambient Temperature 14ºF (-10ºC)Max Ambient Temperature 113ºF (+45ºC)Power Connection 2.1 x 5.5 x 12mmLED Type / Model RGBWLED Life 50,000 hours in ambient 77ºF (25ºC)Material ABSColor Black
Size (L)132mm x(W) 98mm x (H)67mm (L) 5.20” x (W) 3.86” x (H) 2.64”
Universal Fiber Optics6119A Clark Center Avenue | Sarasota | FL34238Tel: 941 343 8115 | 800 UFO 5554www.fiberopticlighting.com